Search Documents

By M. Safiuddin

Within the mining industry, open-pit mining has progressed to a point where a 200-yard walking dragline is as conceivable today as a 35-yard dragline was just a few years ago. This is possible due to the technological advances and efforts of the excavator manufacturers, and the manufacturers of electrical equipment have always stayed abreast with them in meeting their requirements and in making available their experience with the latest control techniques and hardware from various fields for application in the mining industry. An electrician in the coal mines of Pennsylvania who had not heard the word "thyristor" a few years ago now wonders how the old excavators with Rototrols® and magamps could ever work. The thyristors, transistors and operational amplifiers which were considered too fragile and delicate for a rugged and severe application like the mining industry, today constitute the brain of an excavator control taking commands from the operator and giving signals to the muscles of the excavator to move the bucket within a few seconds. A giant 200-yd bucket filled with overburden moves within seconds of the operator's command. Digging cycles for these excavators range from 40 to 60 sec depending on the swing angle. With these tremendous production capabilities of the excavators, the equipment failures and downtime become very expensive, and the loss of return on large capital investment for such machines becomes intolerable. Even though these failures and downtimes cannot be avoided completely, a good preventive maintenance program can help reduce them, thus increasing the machine availability. As we shall see below, the causes for breakdowns and failures of electrical equipment can be analyzed and a good preventive maintenance program can be drawn up to eliminate most of these failures.

Jan 9, 1967

By Granville S. Borden, Frank H. Madison

The fruits of industry are divided between capital, labor, and governments. Capital takes its redemption and remuneration through profits or dividends; labor takes its share through wages; governments take their share through taxes. Each must have a just share, and the question of what is a just share and the question of who shall make the allocation are vital current political and economic issues. Certain political philosophies con- tend that government should take all the fruits and that some dictator or politician should have irrevocable discretion and power to distribute the fruits. Believers in democracy and free enterprise adhere to the view that capital is entitled to redemption and fair remuneration; that labor shall have a fair wage; and that governments shall make equitable levies. But since all human beings, both individually and in groups, are inherently selfish, there are many variable views in regard to the question of what ratios shall be applied in a division of the fruits and who shall have the power to fix these ratios. Perhaps all parties should devote more energy to means of increasing the crop, and not so much time to quarreling over a division of the existing crop. Moreover, all three parties must guard against killing the goose that lays the mineral eggs. For example, if the tax burden becomes oppressive and the taxpayer refuses to carry it, then business stagnates, with consequent unemployment, reduction of profits, and curtailment of government revenue. If a producer assumes the increased tax burden, marginal operations must be closed down, and, again the consequences are increased unemployment and diminished government revenue. Quite often an increase in a rate of tax results in a reduction of government revenue. Perhaps the worst detrimental feature of selfishness and greed on the part of any one of the three distributees of the fruits of industry is the retardation of expansion of the enterprise. Growth means new jobs, more government revenue, better trade, and better standards of living. Explorations and discoveries have resulted in tremendous contributions

Jan 1, 1964

By S. Frederick Ravitz, Kenneth E. Fisher

Four liquids are ordinarily present in the lead blast furnace during lead smelting. At the bottom is the lead bullion, which is metallic lead containing about one per cent of impurities, including gold, silver, copper, bismuth, arsenic and antimony. Above this is the speiss, which consists essentially of arsenides and antimonides of iron and copper. The speiss is followed by the matte, which consists principally of sulfides of iron, copper and lead1. The top layer is the slag, of which the major constituents are silica, lime, alumina, zinc oxide and iron oxide. Similar products are obtained from the dross furnace, which treats the dross obtained in decopperizing lead bullion. The distribution of gold and silver among these various products is of considerable importance in the smelting of lead. In general, the matte and speiss cannot be treated in the lead smelter, and usually are sent to a copper smelter. It is usually desirable, therefore, to keep their gold and silver contents as low as possible, and to collect the precious metals in the bullion. If the bullion, speiss, matte and slag exist together in equilibrium, the gold and silver should distribute themselves among these four liquids in a definite manner, which, other conditions being equal, should depend only on the amounts of gold and silver in the charge to the furnace. It is thus apparent that a knowledge of whether such equilibrium exists is necessary before attempting to study the effects of various compositions of matte and speiss on the distribution of gold and silver among the furnace products2. Moreover, systems consisting of four liquids in equilibrium are very rare, and are of considerable scientific interest. In order to ascertain whether equilibrium existed, the distribution of gold and silver among the four liquids was determined. The speiss,

Jan 1, 1937

El Indio, eighty percent -owned by Compania Minera an Jose Inc., a subsidiary of St. Joe Minerals, and twenty percent-owned by private Chilean investors, will open their new flotation and Carbon -In -Pulp plant near La Serena, 480 km (300 miles) north of Santiago, Chile, in early 1981. The underground mine, at an altitude of 4,270 m (14,000 ft), will produce about 1,270 mt per day (1,400 st per day) of ore containing about 2. 2570 Cu, and gold and silver to the extent of 16 and 254 g per mt (0.47 and 7.4 oz per st) respectively. While construction of the plant was underway, development ore, containing some 1,400 kg (45,000 oz) of gold, was shipped to the United States for recovery in a copper smelter. At El Indio the underground ore is rail-hauled to the mill a short distance from the portal where it is crushed, ground, and floated to produce a copper concentrate containing both gold and silver. The crushing plant also crushes waste for use as mine backfill. Approximately 92% of the copper and 60% of the gold and silver are recovered in the flotation concentrate. Flotation tailings, at a grade of 19 g Au and 116 g Ag per mt (3.4 oz Au and 0.55 oz Ag per st), are cyanided for 72 hours in six Pachucas with auxiliary air lifts for pulp transfer. Lime, cyanide, lead nitrate, and a phosphate are also fed to the cyanidation Pachucas. After cyanidation, the pulp is treated in four air lift Carbon-In-Pulp tanks equipped with external vibrating screens for carbon advance. Loaded carbon is stripped in two pressure vessels in parallel. Pressure stripping must be used because of the high altitude. Stripped carbon is dewatered in a spiral classifier before being reactivated in a rotary kiln and returned to the C. I. P. circuit. Pregnant solution is then sent to four banks of four Zadra cells for gold and silver recovery on steel wool. Zadra cell cathodes.are washed with the slimes being captured in a plate and frame filter. The filter cake and the washed cathodes are then dried on an infrared dryer and smelted in two stages to bullion bars. Published reports indicate that the total investment for this unique operation was in the neighborhood of $80 million.

Jan 1, 1981

SAN FRANCISCO LOCAL SECTION Executive Committee G. HOWELL CLEVENGER, Chairman C. W. MERRILL, Pace-Chairman JAMES C. RAY, Secretary-Treasurer, 1235 Webster St., Palo Alto, Cal. F. W. BRADLEY ANDREW C. LAWSON Meets on the second Tuesday of each month Farewell Dinner to H. Foster Bain H. Foster Bain, Who has gone to London to assume the editorship of the Mining Magazine, was tendered a farewell dinner by the San Francisco Sections of the American Institute of Mining Engineers, the Mining and Metallurgical Society of America, and the Engineers' Club, on the evening of Mar. 9, 1915, at the Hotel Bellevue, San Francisco, 85 members being present. George H. Clevenger acted as Toastmaster and the following toasts were responded to: Bain and the Mining Industry, E. H. Benjamin. Bain, the Geologist, A. C. Lawson. Bain, the Man, F. W. Bradley. Bain, the Friend, C. W. Merrill. Bain, the Schoolboy, C.. F. Tolman. The Frontispiece and Flow sheet from the souvenir program, designed by James C. Ray, Secretary of the Section, are reproduced herewith.

Jan 5, 1915

The first National Industrial Conference was disbanded without accomplishing the results hoped for. A second conference is to be called in the near future. In response to suggestions of members of the Founder Societies, the following telegram was sent, Oct. 29, to the President and each member of his cabinet. "Engineering Council respectfully recommends appointing on new Industrial Conference two or more engineers familiar with industrial problems. Council represents five national societies of professional engineers having forty-one thousand members. Washington office in McLachlen Building."

Jan 12, 1919

By P. L. Weston, S. E. Khalafalla

A systematic study was made by the Bureau of Mines on the effect of so me hypothesized accelerators for the process of wustite reduction in carbon monoxide. When small concentrations of promoter materials in the order of 0.69 at. pct were added to the reducible charge, the rate of reduction to iron was increased. Promotion phenomenon prediction was made in light of a suyface reduction mechanism with the aid of Vol'kenshtein's effect regarding the propagation of crystal lattice disturbances by small amounts of relatively larger interstitial ions. The acceleration produced by a typical promotor, such as potassiunl, increases with protnoter concentration up to a maximum, beyond which the reduction rate decreases. Concentration for maximum promotion depends on the nature and physicochemical properties of the promoter. The extent of reduction rate enhancement is found to be directly proportional to the atomic volume and electronic charge of the additive. DESPITE the enormous volume of literature on iron oxide reduction, very little is reported concerning additive or impurity effects on this important metallurgical process. The beneficial effect bf calcium compound additions on the reducibility of iron oxide sinters has been reported by Tigerschiold,1 vor dem Esche,2 and Edstrom. Doi and Kasai~ found that the addition of lime or limestone to iron ores helps to break up any unreducible compounds, such as fayalite or ilmen-ite. and thus free the combined iron for reduction. Schenck et al. 5 suggested that the increased reduction rate obtained when adding lime could be accounted for by the instability of wustite in the presence of lime. Acid-base slagging reactions resulted in wustite disproportionation according to The dicalcium ferrite formed will yield iron and calcium oxide during reduction. Regenerated calcium oxide dissociates more wustite. This mechanism has been used by Seths and white7 to explain their experimental results. Recently, Strangway and ROSS' attributed the calcium carbonate acceleration of iron oxide agglomerate reduction to increased porosity, both initial as well as that developed during reduction. Aside from calcium carbonate, or oxide, no other promoter was noted in the literature, except for a brief mention by Barrett and woodg on the effect of sodium carbonate and aluminate as activators for the hydrogen reduction of magnetite at 600°C. The present investigation systematically studied a host of other promoters, including calcium and sodium, in an attempt to elucidate the mechanism by which promotion takes place and to fit the results into a simple chemical model. To attain this goal, the effect of promoter physical properties, such as atomic volume, electronic charge, and concentration are related to wustite reduction kinetics in this paper. Wustite reduction to iron, rather than the overall hematite reduction, was chosen since this reaction is known to be the slowest, and hence the rate-deter mining step for the overall iron oxide reduction process. EXPERIMENTAL PROCEDURE Raw Materials and Their Preparation. The pure or impregnated wustite pellets were prepared from minus 400-mesh chemically pure hematite powders. A known weight of hematite was thoroughly and uniformly mixed with a calculated weight of the additive. The mixed paste containing 35 wt pct water was gradually heated from 400" to 1200° C and fired at 1200°C for approximately 4 hr in an air atmosphere. After cooling, the sinter was pulverized to minus 100 mesh and pelletized into minus 4- plus 5-mesh spheres. Pellets were fired, similarly to the paste mix, air-cooled, sized, and stored. An appropriate weight of the charge (20 g) was placed in a zirconia reduction tube maintaining a uniform oxide bed height of 1 cm and a cross section of 7.1 sq cm for all of the test runs. The samples were supported in the vertical reaction tube by a bed of fragmented insulating firebrick plus 3- to 6-mesh alumina beads. The hematite was then transformed to wustite by reduction with a 30 pct CO2-70 pct CO gas mixture at 1000°C in a globar furnace. Complete conversion to wustite was ascertained by a continuous infrared gas analyzer recording the CO-CO2 content of the effluent gas until no carbon monoxide was absorbed from the inlet gas, and inlet-outlet gas analysis remained constant for 30 min. The wustite sample was then reduced with 100 pct CO at 100WC. From the recorded data, an initial rate of reduction was determined by the initial slope of the graph percent reduction vs time. In order to estimate the accuracy of the data, five separate determinations of the reduction curve of pure wustite, under otherwise identical conditions, were performed. The maximum deviation from the average reduction at 14 min amounted to 2 2 pct reduction. This deviation corresponds to 3.8 pct variation based on the percent reduction of the sample. Aiiy impurity effect below the limits of this maximum deviation was considered a spurious result. If the effect exceeded + 4 pct, then it was considered as a positive one. Considerable care was exercised in determining the initial rate from the slope of the initial segments of the curve. Each reduction curve was examined separately on large graph paper and the best tangent to the curve at zero time was drawn. The slope of this tangent was taken as a measure of the initial fractional reduction per minute. Although the time required to reach 50 pct reduction may be of special practical significance, initial rate measurements are invaluable in fundamental studies. These rates provide a measure of the process kinetics on the initial

Jan 1, 1968

By Albert J. Phillips

LEAD is an inexpensive metal produced and consumed in large quantities with certain chemical and physical properties that permit handling the molten metal in bulk. These properties are its low melting point, resistance to oxidation, and its negligible solvent action on iron and steel. Thus, lead is almost always melted in large iron or steel kettles, heated from beneath, and is seldom melted in either directly or indirectly fired furnaces or electric induction or arc furnaces. Even with a modest operation a kettle holding 2 or 3 tons is employed, and the size will range up to 215 tons in the large lead refineries. The methods of handling tin and its alloys are essentially the same as for lead because of the similarity in melting point and resistance to oxidation, although because of the cost of the metal the scale is more modest. In melting lead and its alloys preliminary to a casting operation it is seldom that the melting unit is completely drained of its contents. The usual procedure is to continuously charge solid metal and continuously remove small amounts of liquid metal, so that the kettle is maintained essentially full at all times. For type metals, linotype machines usually employ automatic means of adding the solid alloy to the melting pot in proportion to the removal of the liquid metal in casting slugs of type. In the casting of grids for storage batteries, frequently automatic means of charging solid metal in direct proportion to the consumption of liquid metal in the casting is used. In the manufacture of bearing alloys, new alloy is charged in direct proportion to the consumption of metal in the bearings being cast, so that at no time does the level of the metal in the melting pot lower to any great extent. Even in the manufacture of bulky commodities such as pipe, cable. sheathing, and slabs for rolled sheet, it is the practice to employ a melting kettle of several times the capacity of the casting being made. A substantial level of liquid metal in the melting kettle is thus maintained even after the casting is poured and the original metal level is quickly restored by promptly charging new metal, even though there is no immediate need to proceed with additional casting. This procedure is permissible because the amount of fuel consumed in keeping the lead molten and immediately available for use is negligibly small and the cost is more than offset by the convenience. However, this convenient procedure necessitates study and control of certain properties of lead and tin alloys that are not of serious consequence in most other alloys and for that reason are not well known. These properties are "drossing rates" and "melting segregation." DROSSING RATE Users of lead long ago observed that the rate of dross formation on the surface of the lead in their kettles or pots varied greatly from time to time. This was particularly common in places where both antimonial lead alloys and commercially pure lead were being handled.

Jan 1, 1946

By F. H. Buttner, H. Udin, J. Wulff

Using a modified Udin, Shaler, and Wulff technique, the surface tension of gold Udin, purified helium was found to be 1400 ± 65 dynes per cm for the temperature range 1017° to 1042°C. IN the original Udin, Shaler, and Wulff technique for measuring the surface tension of copper: variously weighted wires were allowed to extend or contract in a copper cell held at elevated temperatures in vacuum. By plotting stress vs. strain for a wire array in one test, the stress at zero strain is obtained. This is the point where the contractile forces resulting from surface tension are balanced by the applied load, according to the expression: y = e=o r [1] where y is the surface tension in dynes per cm; a,,,, the stress at zero strain in dynes per cm; and T, the radius of the wire in cm. The assumption that the wires deform viscously permits the drawing of a straight line through the points on the stress-strain plot. Justification of the assumption has received further experimental support recently.'-' The presence of grain boundaries in the wires requires a correction to the original expression used." Thus: y = d4=T [l- (dl) (ar)Y1 [2] where, n/l is the number of grain boundaries per unit length, and a, the ratio of grain boundary tension to free surface tension. Alexander, Kuczynski, and Dawson in studying the creep of gold wire in vacuum were unable to obtain reproducible values of the surface tension of gold. In plotting stress vs. strain for progressively longer times, they found that the stress at zero strain drifted with time from positive stress values to negative values. Similarly, for the surface tension of silver, reproducible values were obtained only when a purified helium atmosphere was substituted.' Evidently the evaporation rate of silver in vacuum is too high at the temperatures employed to obtain solid-gas equilibrium even in a similar metal enclosure. Thus reproducibility of results is lost. Experimental Procedure The experimental procedure was much the same as that originally developed by Udin, Shaler, and Wulff with a few modifications and improvements. For greater accuracy in strain measurements, knots gave way to cut gage marks as shown in Fig. 1. These were made with a hand-driven lathe in which razor blades serv'ed as cutting tools. Also a more precise cathetometer with a screw accurate to 0.00015 cm was used. The tests were conducted in an atmosphere of purified .helium rather than in vacuum in order to avoid possible evaporation difficulties. Five mil wire of high purity gold (99.98 pct) was used. After cutting in the gage marks, each wire of a series of about 12 was differently loaded by welding a gold ball to one end. This was done by dipping the end of the wire in a cooling gold droplet, previously melted on a charcoal block with a No. 2 acetylene torch. The other end of the wire was strung through a hole in a gold lid and twisted over the edge to hold the wires fixed and in suspension from the lid. The lid and mounted wires were then dipped in pure ethyl alcohol to dissolve any skin oils and dirt on the surface of the wires due to handling. Finally the lid was put in place on an alundum crucible lined with gold so that the wires hung freely within the gold-lined chamber. This whole assembly was next heated in a quartz nichrome wound tube furnace and heated for a few minutes at 600°C to soften the wires. After this anneal the wires were easily straightened with tweezers. The wire assembly was finally annealed 10" to 25°C above the subsequent test temperature for 2 hr. This treatment allowed the grains to grow to equilibrium size and shape. After the anneal, the lid was mounted in front of the cathetometer. The gage length was measured by sighting the 40 power microscope on the upper lip of the lower gage mark for the first reading, then traveling up to the lower lip of the upper gage mark for the final reading. This procedure was repeated four times to give an average gage length value. In this manner the annealed gage length and the final gage length could be measured to determine the strains. During all measurements, grain counts were made.

Jan 1, 1952

By George Packard

THE shaft of the Raven. mine, at Butte, Mont., is an incline 1,700 ft. in length and dipping at various angles. At the top the dip is 70° from the horizontal, but this is gradually flattened until at the 300-ft. level the inclination is only 47°. This angle continues to the 1,100-ft. level, below which it, curves with a 125-ft. radius to 78°. In addition to these variations in dip, the shaft does not lie in the same vertical plane, with the result that the hoisting rope not only rubs at intervals on both the hanging- and foot-walls, but presses strongly against the west, dividers near the collar, while 300 ft. below it runs close to the east end plates. The early operators used no idlers, and wall plates cut 6 in. deep y the rope resulted. Later operators first attempted to overcome the excessive friction, and the wear of rope and wall plates, by introducing solid cast-iron idlers, 3 in. in diameter. To allow for the travel of the rope from side to side some of these had to be 3 ft. long and were very heavy. Judging from the appearance of the old idlers of this type found at the mine, they often failed to turn in the bearings, which is not surprising when it is considered that they would have to make 1,000 rev.. a minute under ordinary hoisting conditions. The next rolls were made of wood, 6 in. in diameter, with an iron band about each end, and a pintle of 1-in. round steel driven in at the ends to serve as a shaft. These wore rapidly, and were soon replaced by rolls made from water pipe, 5 or 6 in. in diameter, cut to the desired length and fitted with a wooden cylinder into which the pintle was driven. Where the idlers were used on the hanging-wall of the shaft the original bearing was simply a piece of 2 by 1-1 in. strap iron, 10 in. long, turned up at the end in a circle of 18 in. in diameter to receive the shaft. A small hole served for oiling, and common black oil was generally used, although filtered oil from engine bearings and compressor bearings was also used. When the rolls were to be placed on the foot-wall the bearings were made from two pieces of 1 by 3 in. steel, 6 in. long. A half circle was cut on the flat side of each piece and the two half circles together formed a bearing. Oil holes were provided, and in some cases holes were bored through the two pieces so that they could be screwed or spiked to the wall plates.

Jan 8, 1914

The paper relates to the laboratory and pilot plant studies that have been carried out by Sherritt Gordon Mines Ltd., Metallurgical Research Div., in developing the ammonia pressure leach process for extracting Cu, Ni, Co, and S from high grade Ni concentrate produced from Lynn Lake ores and describes in some detail the chemistry of the process. In the leaching stage air, ammonia, and sulphide minerals react in a sequence of inter-related steps to produce soluble amines of Ni, Cu, and Co in a solution containing sulphate, thiosulphate, polythionate, and sulphamate ions and a controlled amount of free ammonia, the iron and other components of the concentrate remaining as an insoluble residue which is separated from the leach solution by filtration. The pregnant solution produced in leaching is further treated by boiling to precipitate and remove Cu as cuprous sulphide, leaving a copper-free solution with a composition suitable for subsequent precipitation of Ni and Cu by H,

Jan 3, 1955

By B. C. Burgess

AFTER many years of close and friendly association with talc and soap-stone, this orthographically distinguished mineral steps forth in this edition, for the first time in a chapter of its own. Pyr, the Greek for fire, and phyllite, a rock or stone, form its name and at the same time refer to the first recorded use of pyrophyllite as firestones or hearthstones. Another derivation of "phyllite" is from the Greek phyllites, "of leaves," alluding to the beautiful white radial crystal aggregates that form when pyrophyllite is heated. Pyrophyllite used by the Chinese for carving is called agalmatolite, from the Greek agolma, meaning an image. COMPOSITION AND PROPERTIES Pyrophyllite has previously been grouped with talc because of the close similarity of the minerals in physical and optical properties. They have the same space group; and chemically they are closely related, pyrophyllite being the aluminum silicate A12Si4010(OH)2 and talc the magnesium silicate Mg3Si4010 (OH) 2. Another arrangement of the pyrophyllite formula is generally given as A12034Si02H20 because it expresses the chemical composition as usually determined (alumina 28.3 pct, silica 66.7 pct, water 5.0 pct). Vanderbilt gives pH values of pyrophyllite 5.6 to 8.4.29 Pyrophyllite usually is white, pale green, cream or pale yellow, buff or light gray. It is found in darker shades and other colors principally due to oxidation of contained iron minerals. It is translucent in thin sections. In hardness it is 1 to 2 in the Mohs scale. Its specific gravity is 2.8 to 2.9. In bulk specific gravity, the powdered mineral ranges from 0.4 to 0.7. Its luster is pearly to dull; it is infusible in the Bunsen burner flame, slightly affected by aqueous solutions of sodium carbonate and hydrochloric acid. It is decomposed by sulphuric acid, with separation of gelatinous silica. It is characterized chiefly by its micaceous structure and cleavage, its softness and greasy feel. Two other varieties occur

Jan 1, 1949

By Joseph C. Mead, James R. Cudworth

THE Birmingham district of Alabama has utilized the slag from its blast furnaces consistently since the earliest development of the slag industry. Today there are producers of slag cement who started business in 1900, and who have, under a progressive policy, expanded the number of their products to meet present demands. There are producers of slag aggregates and other crushed slag products who have been successful for periods of over thirty years. There are at the present two companies, Cheney Lime and Cement Co. and the Southern Cement Co., manufacturing puzzolan cement; two companies, Birmingham Slag Co. and Woodstock Slag Co., making slag aggregates and by-products; one company, Tennessee Coal, Iron and Railway Co., a subsidiary of the U. S. Steel Corporation, producing ground open-hearth basic slag for soil conditioning. Two companies, the Sloss Sheffield Steel and Iron Co. and the Woodstock Slag Co., make slag concrete in ready-mix plants and one company, the Superock Company, manufactures fine and coarse slag aggregates under a new granulation process. No Portland cement is made with slag as an ingredient, because dolomite is used so extensively as a blast-furnace flux that the magnesium content of the slag is excessive. Sources Of Slag In the Birmingham district there are 22 blast furnaces, of which the majority are in blast. The present production is 165,000 tons of pig iron monthly; the production in 1935 was 1,297,960 gross tons1. There are also two blast furnaces at Gadsden and one ferroalloy electric furnace at Anniston. From these two sources is obtained slag to approximately 1.1 tons per ton of pig iron.

Jan 1, 1937

By B. S. Gottfried

A generalized mathematical model is presented, which describes the thermal recovery of oil in linear systems with convective external heat loss. Three-phase fluid flow, conduction-convection heat transfer, chemical reaction between oxygen and oil and aqueous phase change are included, making the model applicable to a variety of thermal recovery processes. The complexity of the model requires that numerical solutions be obtained with a digital computer. The numerical approximations of the partial differential equations are presented and the algorithm is discussed in detail. The analysis is applied to the detailed simulation of a forward-combustion laboratory tube experiment. The results of the simulation exhibit with reasonable accuracy all of the principal thermal and bydrodynamic characteristics observed in the laboratory (i.e., the propagation of a combustion zone, a steam plateau, and oil and water banks). Numerical variations in the parameters appearing in the external heat-loss term, the aqueous phase-change term, and the Arrhenius combustion term are examined, and their effects on the predicted temperature profiles, oil and water production histories, and the air-oil ratio are presented. In spite of an oversimplification in the chemical reaction mechanism and the considerable computer time required to obtain solutions, the model represents a major advance in the ability to simulate the phenomena observed in thermal recovery experiments. INTRODUCTION Thermal oil recovery refers to a class of recovery processes where heat is supplied to a reservoir to provide the necessary expulsive energy. This thermal energy can be supplied externally as steam or hot water, or it can be generated in situ by forward or reverse combustion. In either case, however, thermal recovery processes are charac- terized by the simultaneous flow of two or three fluid phases in a variable - temperature field, accompanied by possible chemical reaction or phase-change effects.2-5, 7- 10, 14,16-18,20-22 Although a physical understanding of the thermal recovery processes is far from complete, it is possible to construct mathematical models which describe approximately all of the principal physical and chemical phenomena. However, attempts to solve such models, even with high-speed computers, involve formidable mathematical difficulties. Consequently, theoretical solutions have been obtained only for idealized cases in which important physical phenomena are neglected. For example, consider the process of forward in situ combustion. All such theories which have been developed consider only certain aspects of the process, such as heat transfer, 2-4,8,9,l6,l8 heat transfer with phase change,10 heat transfer with chemical reaction,7 or the hydrodynamics of three-phase flow.21 A general theory including all of the above phenomena has not been developed to date. This paper presents a unified theory of thermal recovery processes in linear systems. A mathematical model is developed which explicitly includes conduction-convection heat transfer with convective external heat loss, chemical reaction between air and oil, aqueous phase change, and the hydrodynamics of three-phase flow. A system of equations is developed which can be solved numerically on a high-speed digital computer, resulting in predicted temperature, pressure, and saturation histories in space and time. The model allows a more detailed simulation of thermal recovery tube experiments than had previously been possible. THEORETICAL DEVELOPMENT Consider the linear flow of gas, water and oil in a homogeneous porous medium. Assume that the oil will react with gaseous oxygen, and that mass is transferred between the water and gas phase by evaporation or condensation. In the absence of hydrocarbon phase change, intraphase diffusion,

Jan 1, 1966

By Michael Tenenbaum

RECENT researches on the reduction of iron ores have stimulated interest in the effect of increased pressures within the iron blast furnace. From a physicochemical viewpoint, it seems logical to suppose that the increased pressure would increase the rate of reduction of the iron ore within the furnace. This increased reaction velocity would in turn be reflected in an increase in the output of the blast furnace. Any sub-stantial effect of elevated blast-furnace pressures should accordingly be of both technical and economic interest to the operator. It is doubtful whether it is possible to increase the pressure in the stack of the blast furnace beyond two or three atmospheres without incurring severe mechanical difficulties. The benefits to be procured by elevations in pressure must therefore be restricted to pressures below two, or at the most, three atmospheres. Within this range it would seem both economically and mechanically feasible to modify the present design of the upper portion of the blast furnace to accommodate these more stringent operating conditions. This investigation was undertaken to study the effect of moderate pressures on the rate of reduction of iron ore with hydrogen. The use of carbon monoxide is contemplated for later work. Although any results that are obtained in the laboratory cannot be interpreted directly in terms of large-scale commercial operations, it is possible, through such an investigation, to ascertain the order of magnitude of the effects of higher pressure. A more quantitative conception of the effects that would result from the use of increased pressures in the modern blast furnace is needed.

Jan 1, 1939

By E. Peters

As in other fields of Extractive Metallurgy, Hydrometallurgy is preoccupied with separation processes and with oxidation-reduction processes. The physical chemistry of each type of process can be described in terms of thermodynamic equilibria and in terms of reaction kinetics. Reaction kinetics are much more important at the low temperatures limiting hydrometallurgical processes than in com- parable pyrometallurgical operations and the number of cases in which the kinetics can be described by simple liquid-phase mass-transfer models are sharply limited. It is convenient to subdivide the applicable rate phenomena into processes in which (a) interface reactions control the rate,(b) mass transfer processes control the rate, (c) solid state process affect the rate, (d) thermodynamically predicted phase changes or molecular reactions fail to take place, (d) metastable substances or supersaturated phases persist, and (elchomogeneous reactions in solution affect the chemistry and the kinetics. Examples are drawn from the unit steps of leaching, cementation, hydrogen reduction, and electrowinning.

Jan 1, 1973

By Geoffrey Gilbert

The Montana Phosphate Products Co., subsidiary of the Consolidated Mining and Smelting Company of Canada, operates three phosphate properties north and northeast of Garrison, Powell County, Mont. Production of all three is from the same phosphate bed, a 3 to 4-ft. member of the Phosphoria formation, whose outcrop is traceable across the mountains of the Garnet Range in a series of southeasterly pitching folds. Because of topographical differences and of variations in the attitude of the bed, each property has its own mining methods and problems. Most of the phosphate rock produced since 1930 has been shipped to the plant of the Consolidated Mining and Smelting Co. at Trail, B.C., where it is treated with sulphuric acid for conversion to phosphoric acid, which in turn is used to produce various fertilizers. History The occurrence of rock phosphate in Montana has been known since 1910, and the Garrison area was mapped by the United States Geological Survey in 1913. In the nineteen twenties William Anderson, owner of a ranch 8 miles north of Garrison, discovered phosphate on his land, and the Montana Phosphate Co., which later became the Montana Phosphate Products Co., was formed to work the deposit. Montana Phosphate Products Co. later obtained United States leases on two adjoining parcels of ground, and this combined property, known as the Anderson mine, has been the main source of Con-solidated's phosphate rock. The mine now includes an adjoining parcel leased from Anaconda and mined from the Anderson workings. In 1940, the Graveley mine, a small privately owned property 6 miles east of the Anderson, was leased from the owner by Montana Phosphate Products Co., and a U. S. lease held by Graveley on some adjoining ground was subleased. In 1943 the Luke mine, on the Mineral Hill property, 1 3/4 miles south-southwest of the Graveley, a U. S. lease, which previously had produced a few thousand tons, was optioned from the lessees by Montana Phosphate Products Co., and is now being developed. At both these mines the rock is appreciably higher grade than at the Anderson mine. Geology The Phosphoria formation is the Permian member of an extensive sequence of Paleozoic and Mesozoic rocks. It is underlain by Pennsylvanian (Quadrant) quartzite and Mississippian limestone, and overlain without any marked unconformity by Jurassic (Ellis) shale and Cretaceous shale and sandstone. In the Garrison area, the Phosphoria itself consists mainly of about 50 ft. of gray to yellow chert. Immediately below the chert is the phosphate, usually 3 to 4 ft. thick. Below the phosphate occur a few

Jan 1, 1948

By Daniel Houdouin

Data is frequently collected in mineral processing plants in order to evaluate operating performance or to model process units. Metal concentrations, circulating loads, products flow rates, classifiers efficiencies, flotation units recoveries, grinding mill efficiencies are typical parameters calculated from plant data. The validity of these calculations depends strongly upon the reliability of the data used for that purpose. The objective of this paper is to illustrate that flowrates, efficiencies and rate parameters of mineral processes are more reliable when calculated from balanced data rather than from raw data. Using variance-covariance matrices of balanced data produced by automatic mass balance packages (including flow rates, concentrations, percentage of solids and size analyses), variances of separator efficiencies (flotation or classification) and of mill grinding rates are derived. The variances are compared with those of variables calculated from raw data. The advantage of using balance data is illustrated with real data from flotation, grinding and classification units.

Jan 1, 1984

By David Cole

THE appearance of the Wilfley table in 1897 marked an epoch in the art of concentration of ores. The table has merited and received an almost unprecedented measure of public approval, lasting through its whole patent life. It has been very little improved in itself, or improved upon by competitors. The new machines bidding for popular favor have been of the Wilfley family, but without ability to do markedly better work than the parent m:-chine, or to (to more work except by the use of superimposed decks, the latter having obvious disadvantages. FIG. 1.-The- Butchart RIFFLE System. During the past three years there has been developed at Morenci a new type or arrangement of riffles applicable to the Wilfley type of concentrating table which corrects many of the objectionable features or limitations of the older system and obviates most of the difficulties encountered with it, particularly when handling ores having a low ratio of concentration. The new type is known as the Butchart1 riffle system, and its general arrangement is shown in Figs. 1 and 2.

Jan 2, 1915

By N. K. Chen, C. H. Mathewson

Single crystals of high purity aluminum of various orientations were carefully documented after plastic extension. Special attention was given to the formation of slip lines, deformation bands, and asterism. An explanation for the geometry and mechanism of formation of deformation bands is considered. WHILE the general process of plastic extension of face-centered cubic metals is well understood,' the accompanying structural changes due to slip and rotation are far more complex than ordinarily assumed. In the case of stretched single crystals of aluminum, the complicated behavior is especially marked by the formation of deformation bands, as first indicated by Collins and Mathewson." Such bands were believed by them and also by others,".'7 who have discussed banded structure in general, to represent one of the important modes of lattice reorientation and to be intimately connected with the recrystallization process. Yet, despite their fundamental importance to the understanding of the mechanism df both plastic deformation and recrystallization, practically no study of the crystallographic features of these bands in their relationship to the conventional slip process has been attempted. This paper describes part of an extensive investigation on the structural behavior during plastic deformation of aluminum single crystals and is especially concerned with the characteristics of deformation bands. The investigation of the subsequent re-crystallization of deformed aluminum single crystals will be discussed in a later publication. Experimental Procedure Single crystal specimens of 99.996+ pct pure aluminum, Yz in. in diam and 5 to 6 in. in length were made both by the Bridgman method5 nd by a modified temperature gradient method.'* Crystals were selected in which the lineage deviation did not exceed 2"; i.e., as determined from the back-reflection Laue X-ray photograms. These crystals were radiographed to insure that no internal porosity was present. The orientations showed good coverage of the whole area of the Taylor and Elam triangle.' Orientations of the crystals were obtained by the back-reflection Laue technique described by Greninger." Crystals so selected were tapered very carefully in a lathe to obtain a linear decrease in diameter from 0.500 to 0.350 in. along a gage length of 3 in. This is considered desirable because it permits a strain gradient to be introduced in a single specimen at one initial orientation. The advantages of tapered crystals for studying the development of slip lines and recrystallized grains have been pointed out by previous investigators." The cold-worked layer resulting from the machining operation was removed by alternate etching in aqua regia and careful polishing with 2/0 emery paper until undistorted Laue back-reflection spots were obtained. A homogenization treatment at 600 °C for 24 hr was then introduced to insure the removal of residual stress. Two of the crystals so prepared were also checked by use of a glancing angle technique. Using a copper target, at 30 kv and 10 microamperes, a monochromatic beam was positioned at right angles to the axis of the crystal about which it rotated. The time of exposure was 24 hr. From these X-ray photograms, it was concluded that the present method of preparation of single crystals is satisfactory. Following this procedure, the crystals were elec-trolytically polished in a 2:l solution of methyl alcohol and concentrated nitric acid. Intermittent

Jan 1, 1952