Search Documents

By A. Bleier, E. D. Goddard, R. D. Kulkarni

The influence of the collector structure on the amine (RNH2, R=alkyl) flotation of quartz has been systematically investigated using a modified Hallimond microflotation cell. This study focuses on the effect of varying chain length, branching in the alkyl group R, polyfunctionality of the collector molecule, and alkyl substitution on the nitrogen atom. In addition, adsorption at the solution/air interface and electrokinetic results for the solid/solution interface were employed to further elucidate the role ad the interrelation of the structural parameters in the flotation process. Estimates of an electrical double layer attractive energy between the bubble and the solid particle are made.

Jan 1, 1976

By Samuel Doak

THE utilization of rotary kilns, of the well-known cement type, for the preparation of iron ores, for the blast furnace, has become of considerable economic importance within the past 10 years in certain localities, notably those where the native ores are lean. Such kilns may be used simply for the agglomeration of ores too fine to be charged into the blast furnace (i.e., ores whose loss in the dust catchers is excessive, and whose fineness is detrimental to the working of the furnace), or for the desulphurization of lump and fine ores the sulphur content of which does not exceed 6 or 7 per cent. The desulphurizing action can be combined with that of agglomeration provided the kiln is sufficiently large. Other processes have been developed for the same purpose, but while I am not able to draw a comparison between them by reason of lack of sufficient data, it is safe to say that the kiln, if properly dimensioned for the character of ore to be treated, will compare favorably in its results, both as to economy and quality of product, with any other process. It is not, however, as well adapted for the treatment of flue dust, as is a sintering operation, on account of the large percentage of fine coke contained therein. Any combustible entering the kiln at its feed end renders the process very much more expensive and unsatisfactory on account of the difficulty of controlling the temperature, also because of the rapidity with which long "rings" form, due to the increased heat at the cooler end of the kiln. The greatest value of the kiln at present is in the treatment of pyrites cinder; that is, the residue from pyrites ore after the extraction of the greater part of the sulphur. This cinder, while high in iron content, has too much sulphur remaining in it to be allowed to form a large part of the blast-furnace burden, without further treatment. It will range in metallic iron from 42 per cent., representing a very low-grade cinder, from a domestic pyrites, to 64 per cent. of the residue from the best Spanish ore, and the corresponding silica content will vary from the maximum of about 25 per cent. to 1 ½ per cent. The residual sulphur depends largely on the type of burner used in the original desulphurization. In general, the leanest original ores retain the greatest amounts of sulphur. In

Jan 9, 1915

By C. E. Lesher

THE Disco* process for the production of low temperature coke and its immediate predecessor, the Wisner or Carbocite process have been described in the voluminous literature of low temperature carbonization.1-4 This paper will describe the development of the process from the first attempt at commercial operation by the American Gas and Electric Co. at Philo, Ohio,' in the 1920's to the successful operation in 1949 by the Disco Co., a division of the Pittsburgh Consolidation Coal Co., of the 1000-ton per day Disco plant near Pittsburgh, see Figs. 1-2. In the 1924 coal industry depression following the hectic post World War I expansion, the northern Appalachian, unionized bituminous coal fields were affected first and foremost, and Western Pennsylvania as hard as any. Competitive market pressure was heaviest on the lower grades of steam coals, notably those from the Panhandle district where ash and sulphur are inherently higher than in the same Pittsburgh coal bed to the east along the rivers. The firm structure of Panhandle coal while favoring the prepared sizes, depressed the usefulness and value of the finer sizes. Panhandle slack and nut slack were marketed with difficulty at consistent, and at times considerable, loss. Many solutions were suggested, and the Pittsburgh Coal Co. investigated all. Lower delivered prices through lower mine costs and more advantageous freight rates were obvious goals, but equally obvious were the difficulties of self attainment of either in any substantial measure. Selling Btu's in pipes was abandoned as an idea after a thorough study of the economics of distribution of what was then, and is even now, the only developed continuous process of complete gasification of bituminous coal-producer gas. Although the coal company purchased huge blocks of electric power, it sold not a car of coal to the central power stations. Public utilities controlled the markets for electric current, and it was found that no matter at how low a cost current might be put on the bus bars by the coal company, distribution to its widely scattered coal mines made such an enterprise practically impossible. Consolidation of underground operations and a huge modernization program of mining operations in the 1920's were but preparation for the introduction of mechanical cleaning of the coal for market, particularly the smaller sizes of steam, gas, and by-

Jan 1, 1952

By Elmer W. Pehrson

Minerals have played a prominent role in the affairs of man and nations since time immemorial but with the advent of the industrial revolution, expanding use of the products of the mineral kingdom became synonymous with the material progress of mankind. Individuals and business groups have recognized this fact so have been aggressive in searching for and utilizing mineral resources, with notable success. Indeed, their achievements are primarily responsible for the present Machine Age. On the other hand, until recently the body politic has failed to grasp fully the essentiality of minerals although, at times, access to mineral supplies has been an important factor in the political maneuvers of nations. This chapter is concerned primarily with the broader political and economic relationships of mineral resources to the world economy, and with the internal and external actions of nations in the field of minerals. Many factors that condition the mineral economy of regions and the world as a whole, influence the internal and external affairs of individual nations. The more important of these are: 1. The nature of man's dependence on minerals. 2. The problems resulting from the unique characteristics of mineral occurrence. 3. Geopolitical concepts. 4. Minerals and world power. Actions of individual nations affecting their mineral economy seek two basic objectives: 1. Attainment and maintenance of prosperity. 2. Military security. Other objectives may be cited but on careful analysis they become integral parts or extreme phases of the two points noted above. For example, the twentieth century aggressions of the USSR, Germany, Italy, and Japan might be considered as direct bids for world power but they also can be interpreted as exaggerated or mistaken efforts toward military security and peacetime prosperity. Similarly, trade barriers, nationalization of industries, foreign exchange manipulations, taxation, monopolistic prac-

Jan 1, 1964

Jan 1, 1945

By E. A. Hartsook

Since World War II we have all been treated to repeated public and private evaluation of the population explosion. Improvements in medicine and agriculture have brought greater life expectancy and a decreasing infant mortality rate. This has brought boom conditions to some areas-and pressures everywhere for the amenities of life: a little elbow room, a tree or a pot of flowers, space to hike or swim with some freedom have all become premium commodities. With this wish for privacy and attractive surroundings, people are being forced to move to once sparsely populated areas. Suburbs expand or sprawl, depending on the point of view. New country is touched by a freeway and houses and stores spring up overnight. Entire new cities are born to meet the increasing mobility of industry and its work force.

Jan 6, 1965

By R. Venkateswar, G. C. Sresty

Size measurement is important in characterization of fine particles. Commonly employed size measurement techniques such as sieving, microscopy, and sedimentation are discussed in this paper. Operating principles, advantages and limitations of these techniques are discussed based on the published information and working knowledge with several of these instruments at the authors' laboratories. A brief description of the recently developed equipment for fine particle characterization is also included. At the end of the paper, a rationale is presented for selection of the size analysis equipment based on specific requirements.

Jan 1, 1980

By Felix Shay

THE Agua Fria mine is in eastern Honduras at Lat. 140° 06' N., Long. 86° 36' W. Danli, the seat of the local municipal government, is the nearest town. The property is approximately 44 miles east of Teguci-galpa, the terminus of a truck road from the Pacific coast. The mine lies at an altitude of 3300 ft. with surrounding elevations as high as 6000 feet. For 20 years the oxidized croppings of the Agua Fria vein had been worked intermittently when in 1927 an attempt was made to open the property. A shaft was sunk 300 ft. and considerable ore was blocked out, but before a mill could be installed financial difficulties arose and the mine reverted to the original owners. Erle P. Halliburton, of Los Angeles, purchased the property in 1934. At that time a careful consideration of all factors involved showed that air transport was the only practical method of moving the equipment and machinery necessary to commence production. The other alternative was by muleback, which required sectionalizing all equipment to a maximum load of 200 lb., and during the rainy season this type of freighting was subject to serious delays. It was decided to purchase a trimotor Ford powered by three Pratt and Whitney Wasp B motors developing 400 hp. each. There were several reasons for the choice: (1) this type of plane was available at a reasonable price, owing to its replacement by faster models on most of the airlines in the United States; (2) the ship was capable of carrying a pay load of 3000 lb. over the required distance; (3) since this airplane had been widely used there would be no difficulty in securing competent personnel or in purchasing spare parts. It was necessary to rebuild the plane for cargo service. The windows were removed and the fuselage was entirely covered. A hatch was cut in the top of the fuselage to receive heavy crane loads and pieces of freight that were too large or too long to go through the rear door. The seats were removed and the interior of the plane was lined with Duralumin sheets. A heavy-duty landing gear was installed and the floor was reinforced.

Jan 1, 1940

By R. T. Hukki

The purpose of this paper is to present an analysis of the unit operation of grinding and the circulating load, of the unit operation of classification and the circulating load, and of the two superimposed into one operation to clarify the overall trend of events relating the circulating load to the capacity of the closed circuit grinding system, to the specific surface area of the final fine product, and to the energy consumption in the closed circuit grinding process. The capacity of the closed circuit is frequently, if not always, determined by the classifier, not by the mill." With these words a startling idea was expressed in 1934 by Dorr and Anable.1 Today, some 30 years later, grinding in closed circuit is universally accepted. The basic curve presenting the capacity factor versus circulating load by Dorr and Anable has obviously been so convincing that not a single authoritative investigation regarding its validity seems to have been conducted. The only major subject of discussion appears to have been the relative merits of the 'high' and 'low' circulating loads. It seems to be universally agreed that much still remains to be hoped for regarding sharpness of classification. BASIC CURVES FOR CONSTANT MILL LOADING Fig. 1 presents a series of basic curves for constant mill loadings in function of new feed rate and circulating load. The mill loading indicated by each curve is the sum of hourly tonnages of new feed and circulating load. For example, at point 0 where the new feed rate is 100 t/h and the circulating load 300%, or 300 t/h, the mill loading is 400 t/h. In closed circuit grinding, the new feed rate corresponds to the rate of finished classified material produced. Although at this stage the effect of classification is excluded in construction of the basic curves, the trend indicated by these curves is strongly in favor of closed circuit operation under relatively small circulating loads. A study of the curves reveals that, e.g., a mill operating under a load of 200 t/h at point P where the new feed rate is 50 t/h and the circulating load 300% will also operate under the same total load at point Q where the new feed rate is 100 t/h and the circulating load 100%. In other words, a reduction of circulating load from 300% to 100% would lead to doubling of the new feed rate and doubling of the rate of production of finished material, without a change in the total mill loading. The obvious question is, is it also possible by a reduction of the circulating load in a closed industrial grinding circuit to increase the production of finished classified material and, if so, how and to what extent? GRINDING TESTS BY DORR AND ANABLE In a series of open circuit grinding tests reported by Dorr and Anable1 limestone was ground at various feed rates in a 3-ft ball mill. The original data are reproduced in Table I. It can be seen that with the increased feed rate production of -65-mesh material increased and the energy consumption per unit weight of the -65-mesh product decreased in the reverse ratio. The data shown in Table I have been reproduced for our purposes in Table II for a scale corresponding to grinding in a large industrial mill. This reproduction

Jan 1, 1968

By T. Egleston

For several years 1 have been engaged in studying the behavior of iron and steel under varying conditions of tension and compression, as well as of shock and abrasion. Some of these observations have been communicated to the Institute at various times. Within the past year I have been looking at the various observations that I have made as a whole, and have been led to the conclusion that there is a regular law of fatigue and refreshment of metals, and that the change which produces either the fatigue or refreshment, is a. chemical one, which is, however, in almost all cases accompanied by physical and molecular changes at the same time. That metals under conditions that were more or less well understood became worthless, has been known for many years. It has been known to blacksmiths that iron and steel, when improperly treated in their fires, become "burned," as they call it, and could no longer be used, and some of them have had a scrap heap into which such material was thrown. A few of them knew that after a period more or less long the iron or steel recovered some of its original properties and could, with many precautions, again be used, but that these phenomena followed any law has not to my knowledge been announced. My attention was first attracted to the varying conditions under which iron and steel rails break in service. It was not long before I became convinced that there was a general law applicable to all metals which allowed of their being used with safety within certain limits, and caused their rupture when the use extended beyond these limits, and this law I have called the law of fatigue- of metals. When me observe the causes of deterioration in iron and steel rails, we find that they are principally shocks, either slight and frequent, like those produced by the passing of a train over a road-bed in good order, which produces a vibration sensible to the ear laid on the rail, for very long distances, but distinctly audible for only a short one; or from sudden and heavy blows, like the descent of the locomotive and each car successively from a high to a low rail.

Jan 1, 1880

By M. Gangal, B. Paul

It may be seen from Maurer's survey (Maurer,l 1966) that most of the common methods used in rock drilling today depend upon mechanical loading of the rock. In order to predict the behavior of rock under an imposed system of stresses, it is necessary to have a valid criterion which delineates those combinations of stress which cause macroscopic rock failure from those which do not. Admittedly, the conditions under which brittle materials fracture depend very much upon statistically variable local effects such as inclusions, grain boundaries, minute imperfections, etc. However, it is extremely desirable to be able to predict fracture under complex states of stress by means of a stress-criterion of failure, where, for a given material, the effects of the other variables mentioned are incorporated into a small number of experimentally observable parameters. One of the most successful of these "macroscopic stress criteria" has been the Coulomb-Mohr theory 2,3 (also see Jaeger 4 and Terzaghi 5), modified by the addition of tension cutoffs (Paul 6). At first thought it might seem rather odd that a macroscopic theory is capable of predicting fractures which originate at highly localized random imperfections at an atomic level (or more likely at the level of individual mineral grains in rocks). However, Griffith7 showed that fractures originating near the tips of randomly oriented elliptical cracks lead to the macroscopic stress criterion of failure indicated in Fig. 1 (a). Fig. I (a) is to be interpreted in the following way: P and Q represent the maxi mum and minimum principal stresses (compression is considered positive) in a macroscopically isotropic body; fracture will not occur for any combination of principal stresses lying within the 'fracture curve' shown, but

Jan 1, 1967

By G. C. Waterman, W. E. Hawes

Mr. Grieves' paper on "Shaft Sinking Today --A Boring Business Tomorrow" in the Dec. 1981 issue of MINING ENGINEERING is an excellent description of recent improvements in speed and costs of shaft sinking. However, shaft boring techniques are not a recent development. In 1935-36, the Idaho Maryland Co. (gold), Grass Valley, CA, bored the vertical 1.5-m-diam Idaho No. 2 ventilation and supply shaft to a depth of 346 m. The equipment was designed and perfected by Branner Newsome and was, I believe, described in "Transactions." Pickands Mather later bored a 1.8-m-diam shaft to a depth of about 305 m using Newsome's design. The Idaho No. 2 shaft cut through hard gabbro, diabase dikes, soft serpentine, very incompetent ankeritized serpentine and a strong fault zone. The completed shaft did not require timber support; the fault zone was cemented. Equipment consisted of a rotating 1.5-m or 3-m core barrel with a slotted bottom which cut a 76-mm kerf. The cutting agent was chilled steel shot introduced into the slot as needed. The driving mechanism and core barrel were lowered into the shaft, the former secured to the wall and the inshaft "engineer" operated the motors which controlled core barrel rpm and advance. After an advance of 1.5-3 m the equipment was lifted out of the shaft, a half(?) stick of powder cut off the drilled core, and it was hoisted to the surface with a cable attached to an eye bolt at the tope of the core. A "shift" consisted of three men: hoistman, equipment operator (down the shaft), and a surface laborer. Advance was variable as equipment and techniques were perfected. Near the end of the job advance was, as I remember, 1.5-3 m per shift. Costs were, as I recall, about $115/m. Up to 4 m cores were lifted out in one piece and swung to the dump by a stiff leg derrick. The Newsome equipment was relatively inexpensive to build and operate and his method should be (more than?) competetive with the methods described by Grieves.

Jan 1, 1983

By L. W. Saperstein, D. Yeung, L. B. Phelps

Introduction The success of preventive methods for the mitigation of coal mine drainage formation will require a marriage of the minimization of initial coal mine drainage formation, the minimization of toxic fluid formation after toxic material disposal, the minimization of the mobilization and transpor¬tation of formed toxic fluids, and the maximization of the rate of diultion and attenuation of the formed toxic fluids. This paper contributes to the understanding of factors af¬fecting mobilization and dilution and attenuation of formed toxic fluids. When water containing a salt content different from in situ pore water in the soil is passed through a body of soil, the concentration of salts in the outflow will gradually change composition in a manner that depends on the kinds of hydraulic processes that occur in the soil. These processes are molecular diffusion, lateral dispersion, longitudinal dispersion, chemical reactions or exchange, physical adsorp¬tion, and biological retardation. This note considers only the first three processes. These three microscopic processes can be analyzed statistically on a probability basis. Such results, confirmed experimentally, indicate that a tracer introduced instantaneously as a point source will tend to form a Gaussian normal distribution as it moves downstream (Todd, 1964). Dilution During Flow The closed-form soltuion for pulse or instantaneous injec¬tion of a tracer during confined flow in a homogeneous porous medium shows that the maximum tracer concen¬tration at a point in space, x, after the time interval, t*, is given by [ ] where Aa is the effective flow cross-sectional area; A is the column cross-sectional area; a is soil porosity; M is mass of the injected tracer; C is concentration of the tracer in the permeating fluid and is a function of x and t*; D is the longitudinal dispersion coefficient; and va is the interstitial fluid velocity (Klotz and Moser, 1974). Therefore, the following conclusion can be made: • For a medium with a constant longitudinal dispersion coefficient, D, a constant soil porosity, a, a constant cross¬sectional area, A, and a fixed mass of injected tracer, M, Cmax will decrease as the time of peak outflow concen¬tration t* increases. • For a medium with a constant longitudinal dispersion coefficient, D, a constant soil porosity, a, a constant cross¬sectional area, A, a fixed mass of injected tracer, M, and a constant interstitial fluid velocity, va Cmax will decrease as the distance of travel, x, increases. • For a medium of constant cross sectional area, A, con¬stant soil porosity, a, a constant mass of injected tracer, M, and a fixed distance of travel, x, Cmax will decrease as D/va increases. Klotz and Moser (1974) concluded that D is about proportional to no.3 where r) is the kinematic viscosity; D is about proportional to a-3 where a is soil porosity; D in¬creases with increasing grain size; D increases as grains become less spherical; D increases with greater grain rough¬ness and angularity; D increases with increasing uniformity coefficient; and D is significantly affected by grain size and uniformity coefficient. The remaining parameters are not significant. Numerical Simulation Studies Numerical simulation studies were used to investigate the nature of flow and the optimum length of a toxic package within a saturated porous medium of fixed dimensions and configuration (Fig. 1). The width and position of the package was maintained constant (Phelps et al., 1981). Results indicate that if the package extends throughout the length of the model, the flow is vertically downward and

Jan 1, 1984

By R. Adair, W. R. Hudspeth, W. T. McDaniel

D. C. Ralston (U. S. Bureau of Mines, Washington, D. C.)—Flake mica can be beneficiated by a wider variety of methods than almost any known mineral. However, most of these methods are not recorded. It is therefore a pleasure to find a written record of another application of a new method of beneficiation. The fact that the Humphries spiral gives a concentrate containing the mica flake mixed with the slime and small grit has forced a further separation by screening, in which the finest of the flake will pass through. Fine flake has its uses and if mixed with slimes or clay is recoverable reliably only by flotation. This loss must be charged against the spiral. On the other hand, the new muscovite mica paper recently brought out by General Electric Co., can be made only with grit free flake larger than 50 mesh. It is of interest to learn from the authors whether the washing of the flake on a 50 mesh screen can take the grit content below 1 pct, to meet this new demand. Must another degritting process be used on the flake, like electrostatic treatment of the dried material? H. D. Snedden (The Humphreys Investment Co., Denver)—When recovering mica in the spiral, gangue particles coarser than 16 mesh can be rejected more readily when operating at a high pulp density (35 pct solids) or a low volume rate (—15 gpm). A launder screen as used by Lehigh Coal Co. has proved very satisfactory to partially dewater the mica concentrate and to reject any gangue slimes it may contain. Under certain conditions mica cleaning in the spiral can be improved by reagentizing the spiral feed, the object being to insure wetting of the gangue minerals and to agglomerate or prevent wetting of the mica particles. R. B. Adair (authors' reply)—The grit content of the mica recovered on Humphreys Spirals varies with the fineness of the launder screen used to clean the mica product. Normal practice has been the use of 80 mesh screen, which will produce a mica product of acceptable grit content for most purposes. By using a 50 mesh screen, and increasing the screen area per ton of feed, it is felt by the authors that a mica of 99 pct plus purity could be obtained. This statement would hold only in the case of mica feed which was well de-laminated, and free from "clay balls," (semikaclinized feldspar), which tends to follow the mica through the process.

Jan 1, 1952

By Y. C. Kim, C. B. Manula

This paper is concerned with the details of the derivation of an operations research model, specifically linear programming, to solve production scheduling problems. While some results are presented for an actual study, the calculation of cases of a more general nature have not yet been completed. Production managers from those segments of the mining industry that experience a seasonal or highly variable sales demand find it rather difficult to develop overall producing plans for their organizations. In an attempt to solve this technical problem, demands are usually met by keeping production corresponding exactly to sales. This results in a fluctuating production schedule which is costly to maintain because of overtime premiums in periods of high requirements and because of costs associated with an idle mine plant during slack periods. An alternate solution may be to produce part of the desired amount and make up any deficiencies by using overproduction in previous time periods. This tends to smooth the production pattern through the use of a stockpile. However, because of associated storage costs, the solution may again be undesirable if it yields comparatively large surpluses. In general, this type of scheduling problem has an infinite number of solutions which satisfy the requirements. These are largely dependent on the extent to which an operation is geared to changes in production and on the size of its stockpiling facility. The determination of an efficient schedule is implied, therefore, as one lying between two extreme solutions, i.e., one that minimizes surpluses and one that minimizes output fluctuations. These conflicting objectives result in an economic balance problem between the costs of carrying surpluses forward from slack periods versus the cost of high production levels during peak demands. Various methods of operations research have been developed to handle problems whose genesis is explained above. It is very seldom, however, that these quantitative means are used in practice by the mining industry. Those who are familiar with mining operations know that most managers have not progressed satisfactorily in this area. Production planning systems which most mines employ today are often no more than rough records of management's mental planning. For small mines these means are normally sufficient; but as operations grow larger and become more complex, this type of planning ability is no longer adequate. Managers may find themselves losing control of cost relationships, taking longer to outline production sequences, and becoming forgetful of certain resource availabilities. ORIGIN AND SCOPE OF A SCHEDULING PROBLEM The more fundamental aspects of the production scheduling problem can be brought into focus by demonstrating how it exists in a bituminous coal mine* located in southwestern Pennsylvania. This mine, operating in the Pittsburgh seam, uses a definite room-and-pillar block system of mining, which is planned and carried out with only slight variations to meet local conditions. The coal seam, which is firm and varying in thickness from 8 to 9 ft with the bottom 6% ft being extracted, is under 500 ft of cover and opened by a shaft. The bulk of the coal (60%) is obtained from the pillaring activity with the mains and sections, which are considered primarily as development activities, contributing the balance of 12% and 28%, respectively. All coal is won by a ripper-type continuous miner in conjunction with shuttle-cars directly behind a loading machine. Track haulage is employed to move coal from these machine centers to the shaft bottom. The coal, thus mined, is shipped to one destination as part of a mixture of coals to be used in the making of steel. A material flow diagram of this distribution scheme is illustrated in Fig. 1. PROBLEM STATEMENT From the above types of shipments and mining limitations, the basic problem is to determine an economic means of producing and stockpiling a single coal product produced in three different machine centers (main, section, and pillar). Fig. 2 shows total demand for coal as a function of time. Because of the extremely high peak demands, slack period production must be stored and then distributed

Jan 1, 1969

By David J. Dunn, Richard G. Martin

Of many physical parameters critical to design of grinding processes, impact of grinding media is among the most difficult to measure or predict. Yet impact of falling grinding balls, pebbles, or rods accomplishes the fine grinding essential to metallurgical recovery of most important minerals. Unfortunately, the same impacts that break ore fragments deform or crack grinding mill liners. A project was undertaken at Climax Molybdenum Company to measure impact forces in operating ball mills so that they might be used to calculate stresses in liner materials and be correlated with service performance of mill liner alloys. Towards that end, a method of measuring impact forces on ball mill liners using an instrumented grinding ball has been developed. Preliminary tests show that impact forces and contact stresses imposed on bare mill liners are quite high but are greatly reduced by cushioning when coarse ore particles are crushed between balls and liners. Compressive and shear stresses induced in liners not protected by coarse ore are so severe that deformation or minute subsurface cracking are inevitable in all but the small production grinding mills, regardless of mill liner alloy strength or hardness.

Jan 1, 1979

By W. F. Boericke

INTRODUCTION THE Wisconsin zinc district, or the Upper Mississippi lead. and zinc district as it is also termed, lies in the southwestern corner of Wisconsin, and embraces adjacent portions of Illinois and Iowa. It includes Iowa, Grant, and Lafayette counties in Wisconsin, and Jo Davies county in Illinois. In Iowa, Dubuque formerly produced considerable lead, but there has been little mining there in recent years. The map, Fig. 1, shows the entire district, with roads, railways, streams, and the various towns, or "camps," around Which the mines. are clustered. The hatchwork indicates the areas iii which lead and zinc have been mined. The district is about 60 mi. (96 km.) north and south and about 40 mi. (64 km.) east and west. Not all of the territory is mineral bearing, and there are considerable areas that are believed to be barren. The grouping of the mines is patchy and irregular, though certain broad zones of mineralization extend almost the full width of the district, as from Mineral Point west through Mifflin and Livingston, and from Shullsburg west through New Diggings and Hazel Green. It is worth noting that the best mines of the district have, to date, been found within 10 mi. east or west of the fourth principal meridian line, thus lying within a long, narrow, north-and-south belt extending the length of the district. In a field as large as the Wisconsin, which has only within com-paratively recent time been worked intensively for zinc, the. chances are good for, opening new and important orebodies in parts of the district not yet, or insufficiently, prospected. However, the prospecting has been most successful around, or adjacent to, the old lead diggings of nearly a century ago, and the camps that were well known then are still centers of activity. In their order of importance they are: New Diggings, Benton, Mifflin-Livingston, Galena, Linden, Hazel Green, Shullsburg, and Highland.

Jan 8, 1919

Jan 1, 1969

AT the Wednesday morning session on Mine Ven-tilation, D. Harrington's report of the committee on metal mine ventilation was presented. He said the only paper which had been received was one from Nevada, although a number had been promised. Mr. Harrington gave instances from his experience where it had cost less to operate ventilating fans during idle periods in mines than the expense of replacing timber, which was destroyed by fungus during the period when the mines were not ventilated. He referred particu-larly to a metal mine in Michigan and a copper mine in the Southwest where this condition had been found in parallel tunnels, one of which had been ventilated after work had ceased and the other had not been. Mr. Harrington also referred to the fumes after blasting operations in mines operating in large bodies of sul-fide ores. By installing mechanical ventilating devices, these conditions had been greatly improved. He re-ferred also to a recent instance where an ignition of sulfide ore-dust had resulted in an explosion which killed three men and burned a fourth severely. Methane had been found in some gold mines and also in tunnels for city water-supply, and as a result coal-mine inspec-tion methods had been adopted. In one instance the contractor had changed from 40 per cent gelatine ex-plosive to a permissible explosive. A daily gas sample was taken. Nitrogen had been found in some of the mines, and CO, gas had been found in some of the Cripple Creek mines where a fan had been installed to maintain pres-sure on the working faces. It was found by experiment that the oxygen was absorbed by the rock particles, which led to a relatively greater percentage of CO. Coal-mine splitting ventilating methods had been used in some places. Miners' consumption had been made compensable in Ontario, and there is a large threat-ened charge now standing against metal mine oper-ators in the Province of Ontario. Mr. Harrington re-ferred to some of the literature, especially the recent book on ventilation by W. S. Weeks of the University of California. He suggested, however, that a better title for the book would have been "The Physics and Mechanics of Metal Mine Ventilation," since it was especially valuable in this field.

Jan 3, 1927

By John R. Don

This paper, under the title of "The Genesis of Auriferous Lodes from a Chemical Point of View, Illustrated by Analyses of Samples Taken from the Chief Auriferous Area of New Zealand, Victoria and Queensland, by John R. Don, D.Sc., M.A., Lecturer on Geology in the University of Otago, N. Z.," was submitted by the author with the frank confession that its length, covering several hundred printed pages of the Transactions of the Institute, would preclude its acceptance for publication in full. But the great value of the original work which it records rendered its rejection on that ground highly undesirable ; and, after correspondence with Dr. Don, it was agreed that the Secretary should condense the paper, subject to the author's approval, omitting what was not essentially connected with the original work reported. In the discharge of this laborious and difficult duty, the Secretary's chief trouble has been his regret to cut out the acute criticisms and admirable theoretical and historical summaries of Dr. Don on the general subject of the science of ore-deposits. It should be added, that the original paper has been returned to the author, with full permission to publish it through any other medium (due mention being made of the first publication by the Institute of portions thereof), and a cordial expression of the hope that the treatise, as a whole, may be thus published, to the advantage of science. The Secretary begs to add, that many of the portions necessarily omitted from this condensed version would constitute, in his judgment, interesting and valuable separate contributions. In attempting to condense this paper, it was necessary at the outset to cut out the tint three chapters, of which the following brief outline is therefore given. Chapter I., introductory in character, indicates the importance of chemical analysis in the investigation of the genesis of ore-deposits, emphasizing the value of Prof. Posepny's Institute paper, and especially of the discussion which it aroused, and stating in general terms the theories of "lateral secretion" and "ascension." Chapter 11. describes the scope of the investigation undertaken by the author, the chief purpose of which was to determine which of the above-named theories was favored by the evidence obtained. This evidence consists chiefly (though not wholly) of analyses of the country-rock taken at various distances from the auriferous "reefs," (a) on deep mine-levels; (b) in the surface or "vadose" region : and also (c) of underlying, neighboring or connected crystallines (granite, gneiss, etc.). In addition to these investigations, there is a separate inquiry into the question of the deposition of gold in marine basins, suggested by the fact that most of the gold in the lodes of Australasia occurs in stratified deposits. Chapter 111. discusses the principles and methods followed by the author in the examination of country-rock for the purpose described. After giving his reasons for believing that careful tests of carefully-chosen samples of country-rock taken at varying distances from the ore-deposit might throw light upon the question

Jan 1, 1898