Search Documents

By J. L. W. Birkinbine

This paper is a discussion of a part of the mineral wealth of the States of Oaxaca and Paebla, Mexico. It does not refer to the precious metals, sonie mines of which, in these States, are said to have been worked before the advent of the Spanish conquistadores in the sixteenth century, as my purpose is to invite attention to the exploration of deposits of coal and iron-ores in the Mixteca region. The prominence given to coal is warranted by the great effect of the scarcity of fuel upon the industrial development of Mexico. Under the progressive administration of President Porfirio Diaz, the Republic has made wonderful advances in the past three decades; and this progress would have been greater but for the limitations imposed by expensive fuel. In the spring of 1906 I was detailed by the Birkinbine Engineering Offices, of Philadelphia, to accompany A. B. Adams, of New York, in a reconnoissance of reported deposits of iron-ores in the State of Oaxaca. The result of this expedition was the formation, in 1907, of the Oaxaca Iron & Coal Co., of which Mr. Adams became, and has remained, President and General Manager, and I have spent the past three years as Chief Engineer of this company in Mexico, principally in western Oaxaca, where field-headquarters were established. GEOGRAPHY AND POPULATION. Although the geographical and topographical features of the Republic of Mexico are well known, few realize that the majority of its population is domiciled in the States which immediately surround the capital city of Mexico, including the Federal District, Mexico, Tlaxcala, Morelos, Puebla,

Jan 1, 1911

By Kiyoshi Mizui

Processes for manufacturing prereduced iron pellets from iron ore dust occurring in iron works have recently begun on an industrial scale. Because of their high porosity and low mechanical strength, these prereduced iron pellets tend to oxidize again and disintegrate into fine particles during transportation and storage; this may result in such difficulties as decreased yield, undesirable work environment and heat generation during oxidation. A possible process for avoiding oxidation and disintegration of prereduced pellets is increasing the density through briquetting. The authors carried out briquetting tests under various conditions, attempting to find optimum briquetting conditions. They found that crushing prereduced pellets and adjusting the particle size to a certain range before briquetting increased the briquette strength and reduced the amount of binder needed. Oxidation resistance of briquettes and raw material pellets was compared in open air and at high temperatures. Briquettes showed superior oxidation resistance.

Jan 1, 1977

By H. G. Schneider

The Smackover oil and gas field lies in Ouachita and Union Counties, Ark., in the south-central part of the state, in T.15 and 16S., R.15, 16, and 17W. It is 10 miles north of El Dorado, the principal business and railroad center in the south-central part of the state, and extends from the town of Smackover in all directions. Productive territory having an aggregate area of nearly 55 sq. mi. has been developed. It extends 6 miles from north to south and 12 miles from east to west. The field may be divided into two parts: the east district, which includes the area east of the town of Smackover, and the west district, which includes the area west of the town of Smackover. In relation to the neighboring productive fields of Arkansas, the Smackover field is 9 miles north of the El Dorado oil and gas field, 8 miles slightly west of north of the East El Dorado oil and gas field, and 16 miles east of the Stephens oil field. Smackover was discovered in May, 1922, when the Oil Operators Tnist drilled well No. 1 on the J. T. Murphy farm, in the southeast quarter of sec. 8, T.16S., R.15W. This well is located almost on the top of the Norphlet dome and was drilled to the Nacatoch sand. It had an initial open flow volume of 30,000,000 cu. ft. of dry gas per day, and a rock pressure of 950 lb. per sq. in. In July, 1922, the V. K. F. Co. completed the first oil well in sec. 29, T.l5S., R.l5W., on the north side of the Norphlet dome, and 3 miles north of the first gas well. This well started the active development of the north and northwest sides of the dome.] The field was extended westwards, when oil was discovered in the Nacatoch sand, during October, 1922, in sec. 4, T.l6S., R.l6W., 51/2 miles west of the original gas well. This opened up the so-called "light oil district," which is located on a structural terrace, for which the name

Jan 1, 1924

By L. I. Cothern

THE introduction of mechanized mining has created a demand for long working faces. It has also prompted mining men to contest the old theory that longwall methods can be used only where roof conditions are ideal and where pack-wall material is plentiful. "Longwall" as used in this paper means "modified longwall," "semi-longwall," or any of the various "wall" or "long-face" methods of mining. Many mines are now using long conveyor faces that differ only in their methods of development, types of roof support and method of loading coal onto the conveyor. Some types of longwall operations are being carried on successfully under conditions heretofore considered impossible by men experienced in longwall mining. With possibly one or two exceptions, long-face methods in Alabama are a direct result of the need for lower mining costs. The advantages over room-and-pillar systems were clearly expressed in an article by Messrs. Fies and Lacy of the DeBardeleben Coal Corporation1 as follows: (1) increased tonnage per miner; (2) increased percentage of lump coal; (3) reduction in cost of development; (4) elimination of the cost of room yardage; (5) reduction in the cost of haulage, from ability to use larger cars; (6) reduction in the cost of machine cutting; (7) reduction in cost for tracks; (8) reduction in the cost of deadwork; (9) reduction in the cost of supervision. An attempt on the part of the operator to gain these, advantages by changing from room-and-pillar to longwall requires considerable courage, and credit should be given to those men who have done their bit to meet the competition of rival fuels. The initiatory problems to be solved are in reference to: (1) retreating or advancing system, (2) length of wall, (3) method of roof support, (4) method of entry development, (5) type of conveyor or loader, (6) hand vs. machine loading (onto conveyors), (7) hand vs. machine loading in entries, (8) control of roof pressure,

Jan 1, 1940

By B. E. Sundquist

The various methods based on solution models for obtaining free energies of mixing from miscibility-gap data have been applied to a number of binary-alloy systems. For nine of these systems there exist experimental thermodynamic data that permit a comparison of the results to experiment. It was found that the method of van der Toorn and Tiedema almost invariably leads to results that are physically unacceptable and that vary drastically with small changes in the miscibility-gap parameters. The subregular solution model is found in all cases, except the Al-Zn, Fe-Cr, and Cu-Pb systems, to exaggerate the free energy of mixing by 30 pct or more. The model developed by Lumsden is found to give results that are often in excellent agreement with experiment and which exaggerate the free energy of mixing by no more than 30 pct. These results and others give evidence that the Lumsden treatment of the effect of unequal atomic sizes and of imperfect configurational randomness due to deviations of AB bond energies from the mean of AA and BB bond energies is adequate for most systems. ANALYTIC expressions are frequently proposed for the dependence on composition of the activities of the components of a solution. Because the development of solution theory is incomplete, these expressions contain parameters which must be determined by experiment. The measurement of activities is often difficult and consequently such measurements are less readily available than are measurements of phase equilibria which, under certain conditions, can also be used to evaluate these parameters. For example, suppose it is known that two structurally dissimilar phases, each of known composition, in an n-com-ponent system are at equilibrium at a given temperature and pressure. n equations can be set up in terms of these parameters expressing the equality of the chemical potential of each component in the two phases. In addition, one can write the Gibbs-Duhem equation for each phase that also contains these parameters. Thus, if these n + 2 equations contain n + 2 parameters, these parameters can be determined (at the temperature in question) from the phase diagram alone. If the average number of parameters in each expression for the activity of a given component in a given phase is V then there will be 2nV parameters involved. Equating 2nV to n + 2 shows that, for n + 2, V = 1. If the temperature dependence of each parameter were to be expressed in some explicit form one could use equilibrium conditions at a number of temperatures to increase V. The situation is much improved when the two phases in equilibrium are structurally similar. It can then be assumed that, stably or metastably, two phases will become one at higher temperatures. Thus the number of parameters involved becomes nV instead of 2nV. Hence, V = 2 for n = 2 using only one temperature. (It is implied here that the activity expressions used are valid over the entire composition range.) In this investigation only the equilibrium of two structurally similar, two-component phases (miscibility-gap systems) will be considered. The various proposed solution models will be applied to a number of these systems and the results compared with available experimental results. All of the analytic expressions that have been proposed for the free energy of mixing of a two-component system are of the form where ?Gmix is the free energy of mixing per mole of solution, N1 and N2 are the mole fractions of components 1 and 2, respectively, and f(Ni, T) is some function of composition and temperature. In the "ideal" solution model f = 0. In the "regular" solution model f = a constant. Since these two models permit only a symmetric equilibrium diagram they will not be considered further here. The simplest model that permits a nonsymmetric miscibility envelope is the so-called "subregular" solution model proposed by Hardy.1 This model gives where the Ci(T) are functions of temperature only. The same expression for f is obtained from the "linear a function" model proposed by Darken and Gurry2 and applied to miscibility-gap systems by Wriedt.3 This model requires that the a function defined by be a linear function of composition (yi is the activity coefficient of component i). This model is not purely hypothetical for it has been found2 to hold true for a number of systems. It is readily shown3 that the f(Nl, T) obtained from this model is of the form given in Eq. [2]. It will be noted that the subregular solution model contains only two parameters and hence both of them can be determined at any desired temperature below the critical temperature, Tc, for a miscibility-gap systems in the manner described previously. At T, the two constants can be determined by equating the second and third derivatives of ?Cmix with composition to zero. Another two-parameter model was proposed by Lumsden4 who set

Jan 1, 1967

By T. T. Read

In discussing the taxation of mining enterprises, it is desirable to place limits of both time and space on the field of discussion. For our present purposes it seems best to limit consideration to taxation of mining enterprises in the United States, and to further limit the subject to taxation under approximately current conditions. Even with such limitations the field is large enough, since in this country we have, in most regions, a number of taxing powers; so that state, county and village tax systems must ordinarily be considered, in addition to our national or federal taxes. Nor is it possible, in discussing United States mineral taxes of today, altogether to pass by similar taxation in earlier periods, or related systems in other countries. It is perhaps hardly necessary to remind you, at the outset, that each age in the history of the world displays its own system of public revenues, and that the taxation systems of today are everywhere different from those of older times. Theories as to taxation have varied according to the economic basis of the society in which they were formulated, and our ideas as to justice in taxation fluctuate with changes in social conditions. The word taxation is used in a fairly definite sense today, but you have only to glance into the history of taxation to find that the paragenesis of ore deposits is a fairly simple subject as compared to the paragenesis of taxation systems.

Jan 1, 1932

The opening session of the Institute was held at the rooms of the American Society of Civil Engineers, No. 4 East 23d Street, VicePresident R. W. Raymond in the chair. After a short introductory address by the chairman, the following names were presented by the Council for election as members and associates of the Institute. They were unanimously elected : MEMBERS. Abbott, James W.,.....Lake City, Col. Abbott, J. J., Jr.,...... Lake City, Col. Bartlett, J. C.,.....Cambridge, Mass. Billings, G. H.,.....Boston, Mass. Blake, Frank C.,.....Lafayette College, Easton, Pa. Dewey, Fred. P.,.....Lafayette College, Easton, Pa. Douglass, Samuel T.,. .. . Ann Arbor, Mich. Emmons, 9. F.,.....New York City. Engle, George U.,.....Philadelphia. Harrington, Dr. Bernard J.,. .. Montreal, Canada. Hayden, Wm. B.,.....Columbus, O. Hill, Leslie C.,.....Capelton, Quebec, Canada. Land, W. J.,......Atlanta, Ga. May, Wm. A.,.....Scranton, Pa. Mills, James E.,.....St. Louis, Mo. Moore, Charles W.,.... Montezuma, Ind. Page, William Byrd,.... Lexington, Ky. Putnam, Douglas, Jr.,.... Ashland, Ky. Richards, Henry,.....Dover, N. J. Boberts, Percival, Jr.,. .. . Philadelphia. Sackett, S. G.,......Brooklyn, N. Y. Schley, Wm. S.,.....Atlanta, Ga. Setz, Gustav,......Mine La Motte, Mo. Talhutt, John H.,.....Lexington, Ky. Torrey, Herbert G.,.... U. S. Assay Office, New York City. Wernlitz, Fred. W.,..., Cartersville, Bartow Co., Ga. Wiestling, Geo. B.,.....Mont Alto, Franklin Go., Pa.

By R. F. Ashton, D. S. Thompson

In reporting results of precipitation hardening experiments, it is customary to include such conditions as solution heat-treatment temperature, specimen size, and quench medium as well as the aging time and temperature. One portion of thermal history that is often overlooked is the effect of the heating rate employed to achieve the aging temperature. It is the intent of this note to demonstrate the importance of the rate of heating to aging temperatures. This work was carried out on the aluminum alloy 7075 aged at 162oC, a temperature commonly used to obtain stress corrosion resistant tempers. A 2 in. thick plate of 7075 was quenched into 24°C water after solution heat-treatment for 2 hr at 470°C. Approximately 13 in. around the periphery of the plate was discarded to minimize quench rate variations, and the remainder was divided into 0.5 by 1.8 by 2.0 in. blocks which were held at room temperature, 24oC, for 4 days. This aging, or incubation period, at room temperature allowed a copious supply of GP-zones to form. Blocks were then heated at various rates to 162oC using the practices shown in Table I. Both single- and two-step aging practices were employed for each heating rate. The single step consisted of heating directly to temperature at the indicated rate while the two-stage practice included an interruption of heating for 7 hr at 107°C. In the case of the two-stage 100°C per min heating rate experiment, the specimens were returned to room temperature after 7 hr at 107°C where they were held for 16 hr be-fore finally heating at this rate to 162°C. This devia-tion in practice is not considered to be significant. Blocks were removed after various times at 162oC, and aging curves were determined from duplicate R. F. ASHTON and D. S. THOMPSON,Member AIME, are Senior Scientists, Metallurgical Research Division, Reynolds Metals Company, Richmond. Va. Manuscript submitted December 2. 1968. IMD Table I. Aging Practices Two-step Single-Step Heating Rate* Aging Aging Heating Method oC per Min A B Programmed Air Oven 0.23 * 0.01 C D Programmed Air Oven 0.93 ? 0.03 E F Air Oven at Temp -10 G H Oil Bath at Temp ˜100 *Heating rate was measured with a thermocouple at the center of a specimen. An average value between the starting temperature and 3°C below the aging temperature is reported for practices E-H. PRACTICES 70 — A B C E and G 50 - 2 4 6 810 20 40 60 HRS.AT 162°C Fig. 1—The influence of processing variables on 7075 aging curves. Fig. 2—7075 aged according to practice H (single-step aged, fast heating rate) for 3 hr. Magnification 100,000 times.

Jan 1, 1970

New York L. W. FRANCIS, Chairman, WILLARD S. MORSE, Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. P. A. MOSMAN, Treasurer. LOUIS D. HUNTOON. WILLIAM A. POMEROY. Boston HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. ROBERT H. RICHARDS, ALBERT SAUVEUR. Columbia FRANK A. ROSS Chairman. RUSH J. WHITE, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. FREDERIC KEFFER, FRANCIS A. THOMSON.

Jan 3, 1915

By C. Feng

HE sensitivity of twinning in molybdenum alloys containing 20 or more at. pct Re was reported by Dickenson and Richardson&apos; and Sims et a1.&apos; The latter3 also studied the effect of twinning on plastic deformation of these alloys. Recently, in this laboratory, the twinning planes in a series of Mo-Re alloys were successfully identified by tracing their boundaries on two known surfaces of the crystals, with the aid of stereographic projection. The nominal alloy composition and the results of the determination are listed in Table I. Metallic powders of molybdenum and rhenium with 99.9 pct purity were mixed, pressed and arc-melted into buttons under purified argon in a water-cooled copper hearth; the buttons were annealed at 2400 °C in vacuum (10-&apos;mm Hg) for 1 hr, remelted under argon and finally reannealed in vacuum at 2400°C for another hour. This treatment yielded a homogeneous alloy. Large-grain specimens devoid of subgrains were obtained with grain diameter varying from 1/8 to 1/2 in. A typical specimen weighed about 15 g. Orientations were determined by taking X-ray back reflection photographs for each grain on a polished surface of the specimens. Two surfaces were cut and polished; the angle between the two surfaces was measured with an accuracy of *2o. The twins were produced by compression in a hydraulic press at room temperature. Usually, several sets of twins could be obtained within each grain. Except in cases where no twins were formed, (Crystals 7, 8, and 9) the twinning planes were identified consistently as the (112) family over a wide range of alloying compositions and surface orientations of the crystals, as indicated in the stereo-graphic triangle in Fig. 1. The twins, however, were not broad enough to accommodate a conventional X-ray beam and no identification could be made of the twinning direction. Nevertheless, the direction must be one that lies in a plane of symmetry perpendicular to the twinning plane. There are only two such possible planes in a bcc lattice, namely the (110) and the (100) planes. Of these, only the (110) planes are perpendicular to (112), and the <111> direction is the intersection of the two perpendicular planes. It can thus be concluded that <1l1> is the twinning direction. The twinning elements of molybdenum have been reported as the (112) planes and the <111> directions,4 which are also the operative elements in other body-centered-cubic metals, such as W, a-Fe, and ß -brass.5 Thus, the present finding of the twinning elements in Mo- Re alloys supports the concept that twinning formation is mainly governed by the lattice structure. It is of interest to note that for specimens containing 12 at. Pct Re or less, no twins were found after being plastically deformed to as much as 30 pct reduction in height by compression, while for the 35 at. pct Re alloy, twins were formed with less than 1 pct deformation. This, of course, does not exclude the possibilities that for Re-Mo alloys containing 12 pct Re or less, twins could be formed under different conditions, such as at liquid air temperature or under impact loading. The present results, however, suggest that under the same conditions twinning is increasingly sensitive with increasing rhenium content. Consequently, the plastic strain at which twinning starts was found inversely proportional to the amount of rhenium in solid solution with molybdenum. This plastic strain necessary to cause twinning may be used as a criterion in the study of twinning characteristics.

Jan 1, 1961

By B. H. Sage

IN recent years there has been an increase of interest in the flow of gases at relatively high pressures. Hydrodynamic calculation of the energy losses in the flow of gases in conduits, as well as through the porous solid materials constituting natural petroleum reservoirs, requires a knowledge of the viscosity of the fluid at the pressure and temperature involved. Although there are numerous publications concerning the absolute viscosity? of hydrocarbon gases at atmospheric pressure, there appears to be little information available relating to the effect of pressure upon the viscosity of these gases. Vogel28 determined the viscosity of methane at 32° F. and atmospheric pressure. His measurements at 32° F. were later substantiated by the measurements of Rankine and Smith17 at 63° and 212° F. Ishida12 also reported values for the viscosity of methane at atmospheric pressure. Trautz and Kurz26 measured the viscosity of propane at atmospheric pressure, from 83° to 530° F., by the use of a short capillary tube. Rap-penecker18 determined the viscosity of gaseous isopentane at elevated temperatures. Day&apos; made an accurate investigation of the effect of pressure upon the viscosity of n-pentane and isopentane at pressures from 2 lb. per sq. in. ? to the vapor pressure at 77° F. (approximately 9.8 and 13.3 lb. per sq. in., respectively). Earhart5 reported data upon the viscosity of several natural gases measured by the long capillary-tube method. The viscosity of air, at atmospheric pressure and 73.4° F., was measured by Harrington7 by the rotating-cylinder method. Kellstrom13 has recently made an elaborate investigation of the viscosity of air at atmospheric pressure. The latter work is perhaps the most accurate investigation of the viscosity of a gas that has been made. .

Jan 1, 1937

By H. B. Pulsifer

.ABOut 1.5 varieties, or tnodifications, of the best rnagnesiurn available were prepared and subjected to etching tests, then examined for micro-structure. Of the 30-udd etching reagents that were tried, nearly half, mostly ammonium salts, etched the metal satisfactorily. The surfacing and etching of magnesium is shown to be a very simple and quick operation. The density and hardness of magnesium were determined. The most interesting new observations relate to the finding of the hexagonal etch figures, the crystal laminations, and the fact that the metal is plastic, cold, when restrained or quickly deformed. Under slowly applied pressule cold metal deforms slightly, then shears to fracture without plastic flow. The chief structural features of magnesium arc presented in two reduced photographs and 30 photomicrographs. Materials Tested There are only two sources in the United States from which new metal can be procured: the American Magnesium Corpn. and the Dow Chemical Co. No pronounced structural or property differences in the metals from these two companies were disclosed by the work of this investigation. The following materials were obtained from the manufacturers: 1. Massive crystals of distilled metal (American Magnesium Corpn.). 2. Rods of hot-extruded metal, ½-in. squares and 5/8-in. rounds (American Magnesium Corpn.). 3. Sheet magnesium, 0.005-in. thick (American Magnesium Corpn.). 4. Cast stick metal, 13/8-in. dia. (Dow Chemical Co.). 5. Magnesium-aluminum alloy, hot-rolled plate, ½-in. thick (American Magnesium Corpn.). From these materials, were prepared: 6. Sections from a furnace-cooled ingot made from clistilled crystal. 7. Cold-strained pieces from (6), (4) and (2). 8. Pieces cold-squeezed to fracture from (6), (4) and (2). 9. Hammer-struck pieces from (6), (4) and (2). 10. Steam-hammer struck pieces from (6), (4) and (2). 11. Sections from furnace-cooled ingot of the magnesium-aluminum alloy.

By Herbert A. Stein, John B. Murdock

AN analysis of perlite expansion furnaces must be based upon one consistent theory which explains how and why perlite does expand when heated. There is more than one such theory, so to establish a basis for the rest of this paper, the authors will outline one theory and the data that support it before going into the construction details of different furnaces. JOHN B. MURDOCK, Associate Member AIME, is President, and HERBERT A. STEIN is Secretary, of the Perlite Corp., Phoenix, Arizona. San Francisco Meeting, February 1949. TP 2736 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Jan. 3, 1949. Why Perlite Expands: Perlite is known to contain some dissolved or combined fluid, probably water, which is lost when the material is heated to fusion. It is generally agreed that when particles of this volcanic glass are heated to fusion in such a way that vaporization of this water into steam takes place at the same time as the glass becomes soft, the steam puffs up each particle into a mass of glass foam. It is a simple matter to expand perlite under a blow torch for demonstration purposes, but in commercial installations, the problem is made more complicated by the necessity of making efficient use of both raw material and fuel, and producing an expanded aggregate conforming to close specifications for size distribution and density, using many different types of perlite rock. The ability of a given operation to fulfill these requirements depends upon the proper handling of four variables. They are: (1) the nature of the perlite rock used, (2) the heating time taken to get the perlite particle up to its highest temperature, (3) the size of the particle, and (4) the maximum temperature the particle reaches. Types of Perlite Rock: Perlite may be classified in many ways, but the characteristics most easily correlated with its behavior in furnaces are its softening temperature, its effective water content, and its "liveliness." Actually there is a close correlation among these three characteristics so it is possible to describe a perlite using any one of them. Lively perlites always have low softening temperatures and high effective water contents, whereas the deader perlites have higher softening temperatures and lower effective water contents. These softening temperatures run from 1400°F to above 2000°F and the effective water contents run from over 2 pct down to 0.2 pct. Included in the category of lively glasses are the green pitchstone from the Edgar claim in Superior, Ariz., the red pitchstone on the Animas highway south of Lordsburg, N. Mex., and a gray glass from Beatty, Nevada. Examples of intermediate perlites (in order of decreasing liveliness) are the Guzman-Lobb perlite with obsidian

Jan 1, 1951

By Adrian Brown

INTRODUCTION The primary tool which is available to improve the stability of an open pit mine at a given slope angle is control of groundwater pressure. This paper sets out the methods by which water pressure control can be achieved in large mines in different materials. The emphasis of this paper is on large mine slopes because. these slopes exhibit the greatest need for groundwater control, the greatest economic benefit from groundwater control, and the greatest technical challenge in achieving groundwater control. STABILIZATION USING MTER PRESSURE CONTROL Groundwater pressures reduce the stability of slopes in two fundamental ways, as shown schematically in Figure 1. In the example, a horizontal failure surface intersects a vertical joint or weak zone. Water pressure acts: o On the base plane to reduce the normal force on the sliding surface and hence reduce frictional resistance to sliding, and o On the vertical back plane, to create a driving force for the system.

Jan 1, 1983

By Gerhard Derge

The rapidity of oxygen steelmaking has created renewed interesl in the mechanisms and kinetics of the various processes involved. These studies can now be approached with increased confidence because of the more adequate thermodynamics, physical chernislry, and relevant engineering infornzation available. These combine to offer promise of useful control and automation if the details of each specific problem can be sufficiently well-defined. The hot filament microscope provides new insig-hi into many of these problems by direct observation at temperature, allowing the appraisal of the relative importance of thermal gradients, convection, and intermediate phases. All of these have a direct bearing on the overall rates and control of most pyrometallurgical processes. It is one of the special privileges of the Howe Lecturer to become better acquainted with this distinguished man. All of us interested in the metallurgy of iron and steel have developed some sense of his widespread influence by the annual reference to his work in these Memorial Lectures. Each lecturer since 1923 has been able to identify his personal specialty with the broad interests of Professor Howe. This has become even more rewarding with the background information from Professor Gensamer&apos;s monograph, "Henry Marion Howe&apos;s Contributions to Metallurgy, which brings out his happy combination of intellectual and professional activities. Beyond this, I found my personal bond with Professor Howe in his book on The Metallurgy of Sleel first published in 1891.&apos; After a detailed discussion of the dephosphorizing action of slags, he relates the mineral species identified in the frozen sample to the chemistry of the fused slag with the question, "Is it not most philosophic to hold that these independent entities were wholly integrated in the initial magma; that their presence in it was wholly

Jan 1, 1968

New York Meets first Wednesday after first Tuesday of each month. J. E. JOHNSON, JR., Chairman EDGAR RICKARD, Vice-Chairman D. MI. LIDDELL, Secretary, 7 Wall St., New York, N. Y. C. A. BOHN, Treasurer JOHN V. N. DORR LEWIS W. FRANCIS Boston Meets first Monday of each winter month. R. L. AGASSIZ, Chairman JAMES G. CARLETON, Vice-Chairman E. E. BUGBEE Secretary-Treasurer, Mass. Inst. of Technology. Cambridge, Mass. W. E. C. EUSTIS G. A. PACKARD Columbia Holds four sessions during year. Annual meeting in September or October. W. H. LINNEY, Chairman OSCAR LACHMUND, Vice-Chairman LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. STANLY A. EASTON S. SHEDD

Jan 8, 1917

By Charles Law McCabe, Lyndon H. Everett, Edna A. Dancy

It has been found that the carbide phase present at equilibrium in the system M-H2-CH4, at about 600°C, is MC for the rare-earth metals Ce and Pr. X-ray diffraction analysis showed that the monocarbides have fcc structures with lattice constants of 5.036 + 0.009Å and 5.131 + 0.001Å for CeC and PrC respectively. Gaseous equilibrium measurements were used to calculate the standard free energy of formation of the monocarbides from the elements. for the formation of (+ 1300) for the formation of PrC. THE rare-earthdicarbides, and their crystal structures, have been known for some years,l but only more recently were the carbides CeC,2,3 Ce2C3 2 and CeCS3 reported. In 1958 to 1959, Spedding et al. published work on the lanthanum-carbon system4 and other rare-earth metal-carbon systems,5 proving the existence of M2C3 and MC2, and measuring the lattice constants. They also demonstrated that tri-rare earth carbides, M3C, exist for the rare-earth metals samarium through ytterbium. However, they concluded that the cerium monocarbide reported by Brewer and Krikorian2 and by Warf,3 and given a fcc structure with a lattice constant of 5.130Å bythe former workers, was, in fact, cerium metal with carbon dissolved in it. They were also unable to find any evidence for the existence of Warf&apos;s CeC3, for which no structural details had been given. Even more recently, Palenik22 reported the existence of only M2C3 and MC2, having been unable to find any evidence for the existence of any other rare-earth carbides. There are no published experimentally derived thermodynamic data for the formation of any of these carbides, although Brewer and Krikorian6 have estimated values of for CeC, Ce2C3 and CeC2. The objective of the present investigation was; to determine experimentally the free energy of formation of any of the reported carbides of cerium and praseodymium, through a study of the rare-earth metal-hydrogen equilibrium. EXPERIMENTAL A methane-hydrogen mixture was circulated, in a closed system over previously prepared cerium or praseodymium hydride, and when equilibrium had been attained, the gas mixture was analyzed by selectively oxidizing the hydrogen and condensing out the water formed. The metal hydrides were used as starting material for convenience because, otherwise, the hydrogen in the gas mixture would immediately dissolve in the metals; in addition, the metals would not react with methane alone at the experimental temperature (around 600°C). The circulating system was based on that used by Browning, DeWitt, and Emmett7 for similar studies on iron carbides. It consisted of a quartz reaction vessel, all-glass circulating pump, analysis tube containing copper oxide that could be heated to 300" C by means of a small furnace, a solid CO2-methanol trap, and a double limb absolute manometer, Fig. 1. A cathetometer, capable of reading to 0.005 cm, was used to measure the difference in height between the two columns of mercury. In its final form, the reaction vessel was enclosed in an outer jacket, containing approximately the same pressure of hydrogen as that within, to reduce errors due to diffusion of hydrogen out through the fused silica of the reaction vessel., The circulating system was supplied with

Jan 1, 1962

By Robert Glass Cleland

WALTER DOUGLAS succeeded his father, Dr. James Douglas, as president of Phelps Dodge in 1916. Before assuming office, the new president had been assayer at Bisbee, superintendent of the Copper Queen, general manager of all the Phelps Dodge mining interests, and altogether had spent a full quarter of a century in various phases of the company&apos;s business. Energetic and imaginative, experienced and courageous, he had need of all these qualities before he surrendered the direction of affairs into younger hands, fourteen years later. For the period of his administration was one of sudden ebb apd flow, flush production, drastic curtailment, quick recovery, and near-disaster. In 1917, soon after Walter Douglas became president, Phelps, Dodge & Co., Inc., which had been formed in 1908 as a holding company, went through an internal reorganization for the purpose of simplifying the structure and changing it from a holding company to an operating company. The Copper Queen Consolidated Mining Company, which had the necessary charter power and authority to carry on the business of any and all the subsidiary com-

Jan 1, 1952

By Charles Smeal, Robert J. Schafer, Max Quantinetz

Normally metal powders cannot be ground to sub-micron sizes because of welding and agglomeration phenomena. Through the use of selected grinding aids and grinding fluids, nickel and other metal powders have been ball-milled as fine as 0.1 It was found that certain inorganic salts are more effective grinding aids for metal powders than conventionally used surfactants. METAL and alloy powders are used to produce reagents, pigments, coatings, solders, brazes, and parts for industry by powder metallurgy techniques. They are also combined with refractory compounds to produce cermets and dispersion-hardened products. One of the interests at the Lewis Research Center has been to explore the potentialities of the dispersion strengthening process. Since the work of Ir-mann, many investigators have shown that the strength of dispersion-hardened products may increase with decreasing interparticle spacing.24 One approach to achieving small interparticle spacing is to combine fine refractory compounds and metal powders, preferably below 1 in size. In attempting to obtain fine metal powders, it was found that until very recently the best that could be obtained from commercial suppliers, particularly of ductile metals, was about 1.0 . Interest was therefore developed in providing finer metal powders for dispersion-hardening studies. Information obtained from the literature, from others working in the field, and from prior experimental work performed at NASA, led to a consideration of ball-milling as a technique to produce the desired materials. Some of the variables associated with ball-milling are the size, material, and nature of construction of the grinding container; the nature and amount of the grinding material and material to be ground; and the nature and amount of the grinding liquid and grinding aid, if employed, and the grinding time. In all ball-milling, welding and agglomeration can oc- cur as well as grinding. Because of the tendency of ductile metals to weld together, they are difficult to grind.5 The ultimate particle size obtained on grinding is generally the one at which the rate of grinding becomes equal to the rate of welding. To help delay welding and thus obtain smaller particle sizes, grinding aids are often employed. The principal objective of this investigation was to produce submicron metal powders by ball-milling the powders with selected grinding aids and grinding fluids. A secondary objective has been to attempt to explain the variations observed in grinding behavior by considering possible grinding mechanisms and correlating various parameters with grinding effectiveness. Three groups of ball-milling experiments were run; one in which the grinding aid was varied, a second in which the grinding fluid was varied, and a third in which the material being ground was varied MATERIALS, APPARATUS, AND PROCEDURE In the first group of experiments in which the grinding aid was varied Inco Carbonyl Grade B nickel powder initially 2.5 (all sizes refer to average particle size as measured by Fisher Sub -sieve Sizer) was used as the material being ground and 200-proof ethyl-alcohol as the grinding fluid. Surfactants, representative of typical organic structures, were selected as grinding aids. Inorganic salts used as grinding aids were chosen on the basis of the size and valence of their ions. Water soluble salts were used in order to facilitate their removal from the slurry after grinding. In the second set of experiments, grinding of the 2.5- Ni powder was tried in four different grinding liquids; water, cyclohexane, n -heptane, and methy-lene chloride. In this study seven grinding aids selected from those tried in the first group of experiments were employed. In the third group of experiments 200-proof ethyl alcohol was again used as the grinding fluid to mill Cu, Cr, Fe, Ag, and Ni powders of various initial particle sizes&apos; All mill charges contained 300 ml of grinding liquid and 3000 g of 1/2 in. stainless steel balls. When inorganic salts were used as the grinding aid, 70 g of salt and 210 g of metal powder were employed, and with surfactants 6 g of grinding aid and 300 g of

Jan 1, 1962

Jan 1, 1969