Search Documents

By J. P. Heller

The purpose of this discussion is to comment briefly on one of the points raised in the paper. The topic is that referred to in the Conclusion 2, in which the authors note a "disproportionate increase in mixing rate" as they proceed from a displacement performed at viscosity ratio 0.998 to one at 1.002. The recovery curve of this displacement, Fig.2A, shows a quite noticeable difference between the two runs in which displaced and displacing liquids were interchanged. This difference is ascribed by the authors to the change in viscosity ratio between the two experiments. This interpretation of the experimental results must certainly be based on rather precise measurements of the fluid viscosities or, at least, of the ratio of their viscosities. The ordinary Ostwald viscometer, employed in the usual way, is only just able to distinguish between liquids whose viscosities differ by two or three parts per thousand. The experimental refinements which then must have been necessary to measure with any precision a viscosity ratio of 1.002 would be worthy of mention. Indeed, one would have expected the authors to devote at least a paragraph to the display of this technique. For the same reason - to emphasize that the details of such unusually critical experimental work should be reported and discussed in the literature — I would have liked to see some comment by the authors on the requirements for temperature control during both the viscosity measurements and the displacement experiments. The temperature coefficient of viscosity of Soltrol C at room temperature has been measured in this laboratory at about - 1.9%/1°C. How much did the coefficients for the fluid mixtures used in the experiment differ from this and from each other Even if the two fluids were identical in this respect, it would appear that a temperature difference of .l°C between them in the flow system would produce a viscosity con- trast equal to that imposed by their composition. Reference to the experimental solutions of these problems would render Conclusion 2 more credible. Published theoretical work on the stability problem contains no indication of such extreme sensitivity to the viscosity ratio in the immediate neighborhood of unity. On the contrary, perturbation calculations such as those made by Chuoke1 and Perrine2 lead to initial finger growth rates proportional to the first power of the viscosity difference. The later instability growth calculated by Scheidegger,3 using the assumption of zero pressure gradient perpendicular to the average flow, is also simply proportional to the viscosity difference. The conflict regarding the sensitivity of the dependence of instability growth or mixing rate on the viscosity contrast needs explicit recognition in the literature. In particular, it would seem that the experimental work reported here should be supported by a more detailed description of the viscosity controls. Further discussion of possible alternative interpretations of the data would also be in order. For instance, is it possible that the unconsolidstted bead pack used changed its characteristics between the runs (due, perhaps, to the handling and inverting involved in the injection of the front) Or, are the data points of Fig. 2A averages from several runs performed in a series in which the two liquids alternated as displaced and displacing fluids? To summarize, it seems to me that the relationship asserted by Conclusion 2 in the paper needs the support of more detailed experimental evidence. REFERENCES 1. Chouke, R. L., van Mews, P. and van der Poel, C.: "The Instability of Slow Immiscible Viscous Liquid-Liquid Displacements in Porous Media", Trans., AIME (1959) Vol. 216, 188.

By Thomas Fraser

UP to the present, there has been no large coal-producing industry in any of the South American countries. Since colonial times, the great mineral and agricultural wealth of that continent has led the people to activities other than the development of manufacturing industries based on coal; and climatic conditions are such that there has been very little demand for solid domestic fuel. However, there are extensive and widely distributed reserves of coal in South America that would make the development of a modern coal industry feasible. That factor is of the utmost significance now, when it is believed that the South American countries are entering the pioneer phase of a broad industrial development. Coal Fields Great areas of coal-bearing formations of Cretaceous and Tertiary ages occur generally throughout the Andean uplift and extend into the coastal range of the Caribbean region far east of Caracas. Thus the west coast countries have adequate reserves of coal, which include a wide range of types and classes. In the eastern part of South America, east of the Cordillera, as in North America, the coal measures are of Carboniferous and Permocarboniferous ages. The principal known deposits in this area are in the southern States of Brazil. Permocarboniferous coals ranging in rank from lignitic to anthracitic are found in the States of Rio Grande do Sul, Santa Catarina, Parana and Sao Paulo. In the great.interior plateau of Brazil, south of the Amazon River, are extensive areas of Carboniferous strata that may contain coal deposits. There are widely scattered reports of findings of coal in' wells and stream beds in northern Piaui and Goias. In the Rio Fresco Valley, explorers have observed outcrops of two beds of anthracite and have brought to Rio de Janeiro samples from these beds. The Fresco is a tributary of the Xingu River that enters the Amazon from the south, but coal could not be shipped by water since the Rio Fresco area is in the upper part of the Xingu Valley, and there is a formidable series of rapids between that area and the lower level of the Amazon River basin. It is doubtful if coal deposits in this general area will be of economic importance for many years to come. Fig. 1 shows the general location of known coal fields of South America that have been explored sufficiently to indicate the presence of workable reserves. The coal deposits of the Andean region are similar in occurrence and general characteristics, as well as in age, to the coals of the Rocky Mountain region of North America. Although the coal fields obviously

Jan 1, 1952

By R. W. Raymond

THE question, what is the best proportion among weight, fall, and speed of stamps, is one which has not yet received thorough and systematic examination. In considering the economical application of stamping machinery, we meet, at the beginning, with serious difficulties in obtaining accurate data for comparison. The weight and fall of stamps vary as the shoes and dies wear out; and this may lead to a change of speed also. Moreover, defects in engines, boilers, or machinery for the transmission of power, may occasion serious losses, which cannot fairly be charged to the arrangements of the stamps proper. Again, the capacity of stamp-mills is directly dependent, in some degree, upon the nature and extent of discharge, fineness of screens, and other peculiarities of the battery. Finally, the hardness and tenacity of the rock crushed varies so much that comparisons between different localities cannot be implicitly trusted. The safest experiments are those made in the same mill, by changing first one and then another condition of working; but this is seldom possible for such conditions as weight and lift of stamps, and only within narrow limits for their speed. We may eliminate of friction, transmission, and generation of power, in the case of stamps, by measuring the power actually developed by their fall. Thus, the weight, multiplied into the fall in feet, and the number of drops per minute, gives us exactly the number of foot-pounds exerted by each stamp. Dividing by 33,000, the number of foot-pounds per minute in one-horse power, we have the horse-power per stamp, from which the effective power of the whole mill may be obtained. Dividing the amount of rock crushed daily by the effective horse-power, gives us the daily amount per horse-power ; and this is the best measure that can be obtained for the effectiveness of the stamps. A complete discussion of the subject would require us to determine the exact influence of the discharge, etc., and the exact resistance offered by different classes of rocks, for both of which points the data are wanting. Professor J. D. Hague, in the third volume of the United States Geological Exploration of the Fortieth Parallel, gives a valuable

By W. L. Fourney

This paper describes a number of model tests conducted in Plexiglas models to investigate the phenomenon of fracture pressurization. The models were examined with high speed photography while being subjected to explosive loading. At the same time pressure transducers were used to record the pressure in the borehole as a function of time and also along the path of the propagating fracture to measure the pressure at various locations along the fracture as a function of time. Both propellants and explosives were used to charge the borehole. Air as well as fluid filled boreholes were needed to provide a variety of pressure rise rates. On some tests eddy current displacement gauges measured crack opening displacements as a function of time. As a final check high speed photographs taken during the event were used to visually ascertain the location of the fracture at any given time.

Jan 1, 1984

Jan 1, 1939

By Thomas Downing

WHEN examining a coal property it is customary for the engineer to take channel samples at several coal faces. In doing so the extraneous matter, or partings, which can be removed by hand, or mechanically, with the facilities at hand, or proposed, is rejected. Where there is doubt concerning a stratum it is usually rejected from the main sample but part is taken for separate analysis. The samples are forwarded to a chemist for proximate analyses and determination of British thermal units, and, sometimes, ash fusion. Consideration is given all available commercial analyses but frequently the owner presents only the favorable ones. From the results thus obtained a general evaluation is made, monies are loaned or expended, markets are determined, and realization is estimated. In many instances, such grades are not substantiated and it is time we looked deeper for a basis which will prove more practical. Institute committees are working hard on analytic and use classifications and much valuable information has already been assembled and distributed. However, no single grade can be applied to any particular bed or region. Much study has been given the Pittsburgh No. 8 seam, yet that bed is subject to material differences in a single section; i. e., some strata of a face may differ from others in structure and analysis, particularly in sulfur content. From some localities it yields a good carbonization fuel, while in others it is chemically unfit for such use. Traveling south to the Logan, W. Va., field we find the Cedar Grove (Island Creek) seam a hard, gray splint coal. In the same field, and not far distant, the same bed changes, both structurally and chemically, and consists of excellent gas coal. In Illinois the moisture content of a bed may vary greatly in different localities. We have seen mines in which part of the coal is excellent for special purpose use but is spoiled by the product from another part of the same mine.

Jan 1, 1931

By Charles C. Towle, Irving Rapaport

URANIUM mineralization along the north flank of the Zuni Uplift, in the vicinity of Haystack Butte, was discovered by Paddy Martinez, a Navajo Indian, in the spring of 1950. The find was reported to the Santa Fe Railway Co., which initiated a program of exploration upon its holdings in the district in December of 1950. The Anaconda Copper Mining Co. secured numerous leases in January and February, 1951, and began an intensive exploration and development program in March 1951. The district was extended into the Lucero Uplift in August of 1951 by the discovery of uranium mineralization in Todilto limestone by Joy Sinyella, a Supai Indian living on the Laguna Reservation. Initial reconnaissance was performed in the district by the Atomic Energy Commission in November 1950. A field office under the direction of the Denver Exploration Branch of the AEC was established at Prewitt, N. Mex. in January 1951 to study regional and detailed guides to ore, to evaluate the ore deposits, and to promote the development of the district by providing geologic services for the companies and individuals engaged in exploration. With the development of sufficient ore to warrant construction of a mill, the Grants area of New Mexico has come of age as a full fledged uranium mining district. The carnotite-type deposits of Grants, the first of major economic importance found in limestone, have extended the Colorado Plateau carnotite field into the more complex structure of the Basin and Range Province. General Geology The Grants uranium district is in northwestern New Mexico, along the southern flank of the San Juan Basin, between the cities of Gallup and Albuquerque. The region is at a mean altitude of about 6800 ft, vegetation is sparse, and outcrops are excellent. Mt. Taylor volcanic peak, at an elevation of 11,400 ft dominates the surrounding area. The overlying cliff-forming Dakota sandstone is the most resistant formation in the Grants District and characteristically erodes into dissected mesas as much as five miles wide. The principle uranium ore-bearing horizons are found in the underlying Morrison formation, and the Todilto limestone of the San Rafael group. The Morrison weathers into. a series of steep slopes and precipitous cliffs near the lower part of the Dakota-capped rims, while in contrast, the relatively resistant underlying. Todilto [ ] limestone forms broad benches extending out from the base of these Dakota rims as much as five miles wide. The Todilto benches are covered with overburden to an average depth of about 5 ft in the first thousand ft away from the Dakota rim, but increases to about 200 ft at the base of the rim. In many places however, a thick mantle of upper Cretaceous sediments and Tertiary volcanics "obscures the ore-bearing Jurassic, and precludes exploration. . The known uranium deposits of the Grants District are distributed throughout a zone 85 miles long and about 10 miles wide. Stratigraphy Rocks from pre-Cambrian through Tertiary are exposed in the uplifted areas, but uranium appears to be restricted chiefly to two zones in Jurassic sediments. The Jurassic sediments of the Colorado Plateau have been subdivided into three units, in ascending order: (1) Glen Canyon group, (2) San Rafael group, (3) Morrison formation. The Todilto limestone zone within the San Rafael group has produced the bulk of ore to date, but the promise of the Morrison zone is rapidly increasing. The Todilto formation extends about 300 miles east-west and about 100 miles in a north-south direction. It is composed of a lower, extensive, limestone member and a central, more restricted, thick, pure gypsum member. The Todilto is believed to be of lacustrine origin. The Morrison formation in this area is subdivided, rather arbitrarily, into three members: Recapture Creek, Westwater Canyon, and Brushy Basin. Ore

Jan 1, 1952

By J. B. Caine

THE investigation outlined in this paper was carried on at the plant of the Sawbrook Steel Castings Co., Lockland, Ohio. EFFECT OF TEMPERATURE In the study of the effect of temperature, heats were made with the Sawbrook company's standard practice, using multiple slags, the only difference' being that the heats were tapped at two temperatures; one group between 2960° and 3040°F and the other group between 3200° and 3250°F. Slags were weighed throughout the heat at each slag change and after the heat was poured. Only the significant slag weights, those of the total slag and the finishing slag, have been reported.

Jan 1, 1947

By J. R. Kyte, R. L. Dalton, V. O. Naumann, R. L. Ridings, R. W. Greene

This paper presents a one-dimensional numerical method for calculating dissolved-gas-drive behavior for a single well or a linear reservoir. Pressure and saturation distributions can be calculated, including the effects of capillary and gravity forces. The analysis has been programmed for solution on the IBM 7090 digital computer. A comparison of experimental and calculated behavior for two linear models demonstrates that the method is suitable for calculating dissolved-gas-drive behavior under reservoir conditions of flow. Dissolved-gas-drive tests were run, at different production rates and with oils of different viscosities, on short (6.ft) and long (173ft) flow models. For tests approximating reservoir pressure gradients and flow rates, there was excellent agreement between experimental and calculated results. A series of calculations of well behavior for thin, horizontal, homogeneous, dissolved-gas-drive reservoirs shows that ultimate recovery is independent of production rate or well spacing in such cases. These calculations also show that Muskat's method and similar material-balance analyses are not applicable under some conditions particularly for high pressure drawdowns. INTRODUCTION The problem of calculating dissolved-gas-drive reservoir performance has received a great deal of attention throughout the oil-producing indusfry for many years. Really significant advances, however, have been made only in recent years. The rapid evolution of high-speed computing equipment and techniques has opened up new approaches to the problem and led to realistic, quantitative analyses free of many of the assumptions and limitations of earlier methods. The one-dimensional numerical method described in this paper includes the effects of both gravity and capillary forces. A number of test calculations, based on different rates, spacings, and rock and fluid properties, have shown that the method is adequate for systems that can be reasonably represented by a one-dimensional model (linear or radial) and in which fluid segregation perpendicular to the direction of flow is not important. Along with the development of mathematical methods, an experimental program was conducted and the data were used to test the validity of the theoretical basis of the mathematical method. Linear models were used and all experiments were run using 1,000-psig bubble-point oils. The use of long, high-pressure models enabled us to more closely approach reservoir gradients and flow rates. MATHEMATICAL FORMULATION DIFFERENTIAL EQUATIONS The differential equations describing dissolved-gas-drive behavior in one dimension dare summarized here. They include Darcy's law for flow of oil and gas (Eqs. 1 and 2) and the equations for conservation of mass for oil and gas (Eqs. 3 and 4). The oil and gas pressures are related by capillary pressure (Eq. 51.

By C. W. Spencer, J. T. Smith

GRAIN-BOUNDARY surfaces are penetrated by a liquid phase when the liquid-solid interfacial tension is less than one-half the tension of the grain-boundary surfaces. Grain growth may occur in the presence of this liquid phase. burke1 reports that grain growth of this nature has been observed in two-phase ceramic systems. He suggests that the presence of a grain-boundary liquid may accelerate or decelerate the

Jan 1, 1963

By S. Skowronski

OvErpolEd copper, as commonly defined,- is copper which has been excessively reduced during the poling period of the refining process. Owing to its porosity, such coppcr is unfit for commercial purposes. The cause of this phenomenon is undoubtedly the lack of oxides in the copper, yet this does not completely explain it. Refined copper of the same "pitch" and "set" varies considerably in oxygen contents, and analyses of overpoled bars also show similar wide differences; moreover, it is possible to melt copper in 'crucibles so as to obtain bars that are practically free from oxygen although they show a "tough pitch" and "level set" surface. Frederick Johnson advances the following theory: The regulation of the quantity of oxygen in copper is the keynote of all copper refining. It is the presence of a well defined proportion of oxygen in the form of cuprous oxide, forming a copper-cuprous oxide eutectic, which enablcs copper to be cast free from blowholes. It seems that when oxygen is present, other gases are less soluble in molten copper; when oxygen is absent, or is present in insufficient quantity, the copper dissolves other gases, such as hydrogen and carbon monoxide, which are insoluble in the copper when solid, and, being rejected during the process of solidification, causes internal porosity and external ridges and excrescences.1 The "level set" of wire bars, etc., is entirely the result of a compromise between the occluded gases and cuprous oxide. With excess of the former the metal would be "overpitch" and spongy, while an excess of the latter would result in the metal being "underpitch" and brittle.2 The result of the absorption and subsequent expulsion of reducing gases, carbon monoxide and hydrogen,' and the effect of this action on the overpoling of copper are in dispute; the literature on the subject is full of contradictory statements and will continue to be so until better analytical methods have been developed. Sulfur, however, is tangible. The refiner can see it in his button sample and consequently attributes to it any trouble that may happen during the melting of the copper.

Jan 1, 1919

By John Birkinbine

(Read at the Philadelphia Meeting, February, 1878.) IN a former paper* attention was directed to the various firms of pumping machines employed for permanent work in mining and metallurgical processes. The following is simply a collection of memoranda of work done of a temporary character, and is presented by way of comparison with other work of similar nature. In close proximity to the charcoal furnace at Pine Grove, Cumberland County, Pa., is a large deposit of superior hematite iron ore, which has been worked for a number of years, and from which many thousand tons of ore have been taken by open pit workings. In July, 1874, the furnace was blown out and operations at the bank suspended, the machinery for draining being removed except a plunger pump, 18 inches in diameter and 66 inches stroke, operated by a steam-engine by means of rods. The pit was allowed to fill with water, and no steps towards its reclamation were taken until November, 1877. At that time the pit was a pond of water at the base of the mountain, having an area of about four acres and a depth of seventy feet. As the pumps, rods, etc., had been submerged for over three years, and partially buried by the mud washed down from the banks, and as it was determined to change the location of the pump for future operations and drive it by water-power, a temporary pumping apparatus was determined upon for reclaiming the pit and keeping it drained until the permanent arrangements could be completed. By opening an old adit about 10 feet of the water was removed, and the area decreased to three acres. The inflow of springs was found to be 250 gallons per minute, and the amount of water contained in the pit was computed to be 45,000,000 gallons. As the inflow would undoubtedly increase while the water sank in the pit, provision was made for removing at least 60,000,000 gallons, at the rate of 1,500,000 to 2,000,000 gallons per day. The company determined to employ a Heald and Cisco centrifugal pump driven by an oscillating engine by means of a belt. Steam was supplied by four plain cylinder boilers, each 36 inches diameter *Transactioiis of the American Institute of Mining Engineers, vol. p. 455.

Jan 1, 1878

By R. G. Bentsen, D. A. T. Donohue

The cyclic steam injection process has become the most widely applied and most successful thermal recovery technique in use today.1-4 Normally, steam stimulation is repeated several times during the life of a project. The problem is to select the optimum number and size of steam treatments so that the profits realized over the entire life of the project are maximum. Obviously, operating costs rise directly with the frequency and amount of steam injection. Operating efficiency, on the other hand, can be adversely affected if the amount and frequency of stimulation are insufficient. Thus arises a multistage decision problem; that is, a decision must be made at each sub-period (day, for example), as to whether steam should be injected, and, if so, how much. It is desirable that these decisions be made in such a way as to secure maximum net profit before taxes. This can be achieved by dynamic programming. To use dynamic programming, we must be able to predict not only the production rate-time curve resulting from a given stimulation, but also how changes in stimulation policy will affect this curve. In this study, the effect of steam injection on well performance is estimated on the basis of a simple model that takes into account both steady-state and transient flow. Oil production rate is calculated for both types of flow, and the larger of the two values is used. This allows the calculation to change to radial steady-state flow at such time as this mechanism becomes more effective than the transient mechanism. We propose to show how dynamic programming can be used to optimize the steam soak process with respect to net profit. For this, a mathematical representation of the steam soak technique is necessary. A further objective, therefore, is the formulation of a mathematical model capable of realistically simulating the physical process. Oil Production Response Model The advantage of using a mathematical model is its generality and ease of manipulation. However, the model must be an accurate representation of the physical process, for a solution derived from a model can be no better than the model itself. The question now arises as to how well the model should be expected to simulate reality. In general, the simplest model should be tried first, for additional accuracy is apt to require additional cost and time. Also, the search for a high degree of accuracy may yield only greater complexity and difficulty without yielding significantly better results. With this in mind, we kept our model as simple as possible, yet generally representative of the actual physical process. The number of state variables is limited to three, and stochastic variations in the parameters are ignored. As a consequence, use of this model should be restricted to cases in which the underlying assumptions are not severely violated. In

Jan 1, 1970

By Martin Mayers

FIVE-SIXTHS of all the coal that is mined in the United States is burned, without previous treatment other than screening, for the produc-tion of heat and power, so that its value is fixed by its suitability for this purpose. Nevertheless, the characteristics of individual coals that determine their fitness for use in particular pieces of combustion equip-ment are not yet well known. This condition is due not only to the small extent of our knowledge concerning coal itself, but also to our compara-tive ignorance of the nature of the combustion process. The following paper is an analysis of the combustion process as it occurs in industrial furnaces, based largely on the results of laboratory research on combus-tion rates. From this analysis it is possible to determine the characteris-tics of the fuel that limit the capacity of a given piece of combustion equipment. Limitations imposed by other factors than the attainable speed of combustion will not be considered, since they are subject to a different type of analysis involving the balancing of maintenance costs against fixed charges. In order to observe the relations among the various factors that affect the speed of combustion, representative particles of fuel will be followed through two types of furnaces. A pulverized-coal furnace will be con-sidered first, because the independence of the individual particles facili-tates the analysis of the effect of furnace conditions. The second example will be a grate-fired furnace in which ignition of the fuel takes place on the underfeed principle. This includes both underfeed and chain grate stokers,(8)? but does not include hand-fired furnaces and some overfeed stokers. The furnace will be considered to be large enough, the tempera-ture high enough, and enough air provided, to burn the fuel completely, without, for the moment, specifying these quantities more completely.

Jan 1, 1934

By Norman Braly

THE following is not offered as an extended paper on the subject of shaft sinking, but more as a description of the present practice of shaft sinking in the Butte district. The Anaconda company is sinking at present the following shafts: Badger State, Moose, Mountain Consolidated, Mountain View, Pennsyl-ania and Tropic. At the High Ore and Leonard mines the shafts are being deepened by sinking two compartments and will subsequently be enlarged to the full working size by raising alongside the compartments which are now being sunk. The following other companies are also sinking shafts: Butte-Alex Scott, Butte and Zenith City, Boston and Corbin, North Butte Mining Co. (at the Granite Mountain shaft), East Butte Co. (at the Pittsmont shaft), and the Rainbow Lode Development Co. Shaft Timbering. The shafts of the Butte district, generally speaking, are of three compartments arranged in a straight line, and the pump compartment is usually arranged for the use of an auxiliary hoisting cage, as well as for carrying pipe lines and electric wires. The Rainbow shaft is practically square, and of three compartments. The length of the shafts outside of timber will vary from 17 to 22 ft., and the width from 6 ft. 6 in. to 7 ft. Fir timber is used in all shaft work. This may be obtained from the Coast, when it is known as Coast fir, or from Idaho or Montana, when it is known as native fir. The native fir seems to be the tougher wood, but it is hard to obtain clear lumber in the lengths and sizes necessary for shaft work. Some of the shaft timber of the Anaconda company has been treated with creosote as a preservative, but this practice has not come into general use, as the ground of the camp is so heavy that the timbers usually crush before they rot. The size of timber most .used for shaft work is 12 by 12 in., while 10 by 12 in., 10 by 14 in. and 12 by 14 in. are used for some of the special pieces around the shaft. The new Leonard shaft is timbered with 14 by 14 in. wall plates throughout.

Jan 8, 1913

By E. H. Hamilton, H. C. Vacher

The limiting concentrations of carbon and oxygen which may CO-exist at equilibrium in liquid iron are important in determining the degree to which liquid steel may be refined before it is deoxidized. Most refining processes depend upon the oxidation of a highly carburized iron which invariably results in contaminating the steel with oxygen. The oxygen thus introduced presents many problems to the refiner, who in turn has attempted to rid the steel of this impurity by deoxidation witch elements such as manganese, silicon and aluminum. The importance of the limiting concentrations of carbon and oxygen is accentuated in view of a number of recent researches which have indicated in many instances the existence of relations between oxide inclusions and dissolved oxygen and physical properties and chemical behavior of steel. The determination of the equilibrium concentrations of carbon and oxygen existing in iron under steelmaking conditions is obviously of fundamental importance. It has been generally assumed that the product of the equilibrium concentrations of carbon and oxygen in liquid iron is a constant and that this product is directly proportional to the carbon monoxide pressure in equilibrium with the liquid iron. Hertyl.2 has computed values for this product based on open-hearth data which are all in the neighborhood of 0.01 to 0.03 (per cent. FeO X per cent. C) for temperatures in the vicinity of 1550" to 1600" C. and one atmosphere pressure. Kinzel and Egan % have attempted to determine the value of this product by exposing liquid iron to carbon monoxide at one atmosphere pressure. The value reported by them was 0.0005 at 1550" C. In order to apply certain equations to the rate of carbon elimination in the open-hearth process, Feild4 found it necessary to assume a value of 0.0102 at 1580" C. for this

Jan 1, 1931

By John Brown

As a part of a symposium on the relations of structure to ore deposi-tion, in February 1938, the writer presented some tentative opinions derived from his experience with a number of important lead-zinc replace-ment deposits. These ideas were set forth, as a basis for discussion and a stimulus to further inquiry, in a mimeographed leaflet that read as follows: Intimate acquaintance with a number of lead and zinc deposits in metamorphosed limestones seems to indicate the existence of certain common features from which can be established some general principles governing the localization of ore in this type of formation. It is suspected that these principles can be applied, with modifica-tions, to mineralization in unmetamorphosed limestone. In metamorphosed forma-tions, some observed rules are as follows: 1. Bands or masses of pure limestone are very resistant to replacement by ore solutions, and are likely either to contain no ore or to resist replacement until near the end of mineralization. The reason for this apparently is physical, not chemical, since microscopic data indicate that when ore is deposited by far the greater part of it substitutes for carbonate. The chief factor is believed to be a lack of porosity in massive limestone that has undergone flowage and recrystallization. 2. Masses of intensely siliceous or silicated rock are likewise unfavorable ore receptacles. This seems to be accounted for by two factors: (a) chemical unsuit-ability or resistance to replacement, and (b) physical resistance to small-scale brecci-ation, which might facilitate the opening of effective channelways for solutions. Some low-grade ore may occur, however, and also sporadic fracture fillings. 3. The optimum condition for ore reception appears to be found in bands or areas containing carbonate and silicates (or quartz) intimately mingled in something like equal proportions. In this situation movement is likely to result in mixed flowage and fracture, producing a fine-textured porosity that admits solutions freely and provides access to an abundance of replaceable carbonate. Cleavage cracks in some minerals such as diopside are believed to facilitate the penetration of solutions. 4. Certain minerals or assemblages are regarded as favorable impurities in a lime-stone and others as unfavorable. Original quartz, and subsequently developed diopside, and perhaps garnet, are typical favorable pre-ore gangue; in general rather equidimensional, brittle minerals. Tremolite, biotite, and probably wollastonite, are typical unfavorable pre-ore gangue; in general highly elongated and somewhat flexible minerals likely to develop under strong shearing stresses. 5. Tentative opinion is that the ratio of lime and magnesia in a limestone-is of little or no importance.

Jan 1, 1940

By H. Reginald Hardy, Gary L. Mowrey

Field studies were conducted over a longwall coal mining operation to investigate the feasibility of using microseismic techniques to detect and to locate any areas of instability in the vicinity of the longwall. An array of geophones buried at depths of 3 to 8 m from surface were positioned approximately 130 m above the active area of the longwall panel. A mobile microseismic monitoring facility amplified, filtered, and recorded the microseismic activity sensed by the geophones. Microseismic events were detected at depths of at least 130 m and at horizontal distances in excess of 250 m from the source. Most events, which resembled decaying sinusoidal transients, had frequencies of 10 to 100 Hz, and particle velocities of 1 to 8 pm/s. Source locations for the 150 largest events were computed using a least-square travel-time-difference method. Both isotropic and unique wave propagation velocity models were considered when evaluating the source locations. Most of the events were computed to be within ± 30 m vertically of the coal seam and ± 15 m horizontally of the longwall face, when the unique velocity model was employed.

Jan 1, 1980

By R. H. Olds, B. H. Sage

The formation volume and volume of the liquid phase of oil and gas obtained from four fields in the San Joaquin Valley have been investigated at pressures, temperature, and gas-oil ratios comparable to those encountered in underground reservoirs. All the fields covered in this investigation yielded a product of a gas-oil ratio in excess of 5000 cu ft per barrel and the gravity of the tank oil for the four fields in question varied between 52° and 63' API. The results of the investigation, together with analytical data concerning the composition of the oil and gas, are submitted in tabular form. Rough correlations of the formation volume as a function of pressure, temperature, and gas-oil ratio and of the retrograde dew-point pressure as a function of gas-oil ratio, temperature, and gravity of tank oil are presented. It was not found feasible to correlate simply the formation volume of the liquid phase as a function of the applicable variable. It is desired to emphasize that these correlations are considered applicable only to the range of conditions covered in this investigation and for systems of similar nature and composition. Introduction Information concerning the physical properties of mixtures of oil and gas from particular fields have often been employed in predicting the situations obtaining in underground reservoirs. One of the earlier studies of this nature was the work of Beecher and Parkhurst,1 while a more recent study of the Dominguez Field2 presented detailed volumetric data in the two-phase as well as in the single-phase regions. Although these studies were confined to individual fields, their results proved of value in application to other fields. It has recently been shown 3,4 that it is possible in the region of low gas-oil ratios* to correlate the volumetric behavior of naturally occurring hydrocarbon mixtures from a single geographical area with sufficient accuracy to be of industrial value. For this reason it is considered of interest to submit information concerning the volumetric behavior of oil and gas mixtures from four different fields in the San Joaquin Valley and, in combination with similar published data5 concerning mixtures of oil and gas from the Paloma field in the same area, to show rough correlations between the composition and the behavior of materials from these fields. This effort seems particularly worth while since all of the

Jan 1, 1947

By J. W. Miller

One of the major problems confronting coal producers in this highly competitive era is whether or not the potential profit to be made from the products of coal flotation would warrant the capital investment required for the necessary equipment. The author supplies two theoretical cases to illustrate methods for computing such costs.

Jan 3, 1961