Search Documents

By G. G. Gunther, C. L. Boeke

THE zinc deleading processes at the Parral and Santa Barbara mills are described separately to provide a basis for comparison. Although the two procedures are fundamentally alike, there are some differences in application to meet specific conditions. The Asarco mill at Parral in the State of Chihuahua is a flotation plant treating 1450 metric tons per day of complex sulphide copper-lead-zinc ores. In general, the procedure used for selective separation of the minerals into a copper, a lead, and a zinc concentrate follows the usual practice. First, a bulk copper-lead concentrate is floated and then separated into a final copper and a final lead concentrate by the sulphurous acid process. A small tonnage of high grade gravity lead concentrate is tabled from the bulk copper-lead cleaner tailing before it is reground so as to avoid undesirable over-grinding and sliming of this portion of the lead mineral. Next, a zinc concentrate is floated from the lead rougher tailing and, as described later, is separated into a final lead product and a final zinc concentrate. Finally, the zinc rougher tailing receives a strong scavenger float to remove all recoverable middling values for regrinding and return to the flotation circuits. The slime is separated from the scavenger flotation product, and only the sand portion goes to the regrind section. The minerals in the separated slime are extremely resistant to all methods of selective separation and pose one of the major problems awaiting solution. Nevertheless, the slime shows a profit when mixed with either the lead or the zinc concentrate, except when metal prices are very low, so it is accepted as a final product for lack of a more profitable method of handling it. In contrast, the minerals in the reground sands of the

Jan 1, 1953

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

The Grand Isle sulfur mine is located in the Gulf of Mexico, approximately seven miles off the coast of Grand Isle, Jefferson Parish, La. The deposit is on acreage covered by oil, gas, and mineral leases originally issued in favor of Humble Oil & Refining Co. by the State of Louisiana which were continued, maintained, and redesignated by the U.S. Department of the Interior after passage of the Outer continental Shelf Lands Act. The sulfur deposit was discovered in 1949 when Humble Oil & Refining Co. penetrated more than 200 ft of sulfur-bearing limestone in a zone between 1813 and 2075 ft below sea level. In 1954, Humble drilled ten more sulfur prospect holes, eight of which encountered sulfur ore.

Jan 6, 1960

By Maurice Grieves

The great majority of shafts constructed today are still excavated by drilling and blasting, a method which changed very little in over 100 years until the introduction of the mechanical lashing unit and cactus grab by the South Africans, which enabled muck to be removed as fast as massive hoisting systems could handle it and resulted in very rapid rates of sinking. Record breaking month's performances were achieved at -Hartebeestfontein No. 4 shaft, October 1960-337.1 m; Western Reefs No. 4 shaft, October 1961-340.7 m; and Buffelsfontein eastern twin shaft, March 1962-381.2m. The method was very labor-intensive, requiring a crew of over 60 workers at the shaft bottom during the drill cycle. Safety precautions were strict, but in the drive to achieve rapid advance, cases of personal injury were still somewhat high because of the large number of people engaged in this potentially hostile environment. The South African method, as it came to be referred to throughout the rest of the world, was adopted in the United Kingdom in the late 1950s in a modified form with greatly reduced manpower and nonsimultaneous sinking and lining, which was insisted on by the British Mines Inspectorate. In that instance, it was successfully used to sink the 7.3-m-diam concrete-lined shafts at Kellingley to 770 m depth, with rates of advance of over 90 m/month achieved, a British record at that time. During the sinking of the 1.15-km-deep twin shafts at Boulby potash mine in the UK in 1970, the method was again used, but for the first time ever in Britain exemptions from the mining code permitted the use of crash beams, crash doors, jack catches, and semi-simultaneous sinking and lining techniques. New British shaft sinking records of over 120 m/month were achieved in both shafts. Similar equipment and techniques were used in the early 1970s to sink several deep shafts in Canada, notably Creighton #7 and the Con zinc mine at Yellowknife in the NW Territories. Today, this equipment is standard for deep shafts in the US and the rest of the world. However, with the tremendous escalation in mining labor costs, the impact of health and safety legislation, and environmental regulations, coupled with a very real shortage of miners willing to work in this exposed situation it was apparent that an alternative to the labor-intensive conventional method of shaft construction had to be found. Recognizing the trend is inevitable, one or two major German shaft sinking contracting firms began to take a fresh look at full face boring techniques applied to tunnels and raise bored shafts. The results were most encouraging. Tunnel drivage techniques using moles had developed considerably from Colonel Beaumont's original channel tunnel machine circa 1880 to the superbly engineered Priestley machine selected to cut the British side in 1975 and the double shielded Robbins Grandori borer on the French side of the English Channel. Full face tunnel machines were being successfully used to drive uphill in inclined shafts in Austria and Switzerland. At Mapprag in Switzerland, the Demag mole drove the first (intentional) vertical transition and curve, and then went on to successfully complete the 730-m-long penstock shaft at an inclination of 35°. In Austria, the Wirth mole drove the Kaprun Glacier ski-lift railcar tunnel at record breaking rates of 457 m/MONTH (best 30 m/d) through green schist at an inclination of 29° for a distance of 3.35 km while the Hydro tunnel at Sarrelli in Switzerland was being driven by the Robbin's mole at an inclination of 35°. Simultaneously, extremely promising results were obtained using large assemblies of cutter discs on raise borer heads, such as the 4.87-m-diam X 460-m-deep shaft raised by Teton for Jim Walter Resources Inc. Bearing in mind that most mine shafts in the future (unless in exceptionally competent rock) will require some form of lining, and the trend will be toward deeper shafts as the more easily accessible mineral deposits become exhausted, it was seen that normal raise boring had definite limitations in vertical accuracy, in the limitation imposed by the drill string on the available torque that could be applied to the cutter head, and in the risk of collapse of the unsupported shaft rock wall in friable or jointed and fissured ground, since it is not possible to apply any form of temporary support until the permanent lining is being installed. A further problem was the economics of installing a subsequent lining, necessitating setting up a headgear and hoisting arrangement approaching in size that required for conventional drill and blast sinking and lining. Because of the economics, German contractors opted for a phased transition from drill and blast to the full face, rodless, out of the solid shaft mole, by starting off with a down-the-hole shaft boring machine -without a drillstring-but using a pilot hole to get rid of the muck.

Jan 1, 1982

Jan 1, 1947

By W. H. Bassett, C. H. Davis

The late J. P. Sparrow, chief operating engineer of the New York Edison CO., carried out a series of practical tests on condenser tubes of several copper alloys and reported on the results to the Association of Edison Illuminating Companies at its meeting in September, 1913. In the preparation of these tubes the senior author had the pleasure of cooperating. Copper-zinc alloys in the proportions of 60-40,70-30,80-20, 90-10, and Admiralty metal, which is in effect 70-30 with 1 per cent. of tin, were tried. Monel metal and several copper-nickel alloys, and 8, 5, and 3 per cent. aluminum bronze were also tried. At the time of this report, the aluminum bronze had been in service for 4 1/2 years and seemed to be giving especially good results but later it began to fail and showed no substantial improvement over Admiralty metal. Monel metal was unsatisfactory and the nickel alloys apparently did not give better service than the Admiralty alloy. Previous to the publication of the report, and after considerable discussion, it was agreed that a test where tubes of different kinds could be under laboratory observation would be advisable, so the apparatus described here was set up in The American Brass Co.'s Waterbury Laboratory. This was fitted with tubes of copper, brass, bronze, nickel silver, cupro-nickel and other alloys, and the test started on Oct. 11, 1912. Salt water from East River, New York harbor, was barrelled and transported to the laboratory for the test. A fresh supply, completely replacing the water in service, was obtained at the end of each six months period. Plan of Procedure In general, the procedure was to inspect the tubes at short intervals and to remove those that had begun to leak. The tubes removed were carefully examined and a photographic and microscopic record of the

Jan 1, 1925

Masjid-i-Sulaiman Field.—During the past year, drilling activities have been limited to repair work. No new developments of importance can be recorded in production technique. Fall of dome pressure is maintained at the 1 lb. per sq. in. per annum rate mentioned in previous reports. Acid treatment of wells is being increasingly used and for wells in fissured areas has been very successful. Such wells have been converted into first-grade producers with substantial drops in bottom-hole differential pressures. The effect of acid treatment has been to increase the flowing lives of wells so treated. The normal procedure consists of threo treatments of 500 gal. commercial acid diluted 100 per cent but success has been met with fewer applications. The policy of returning products to the resorvoir has been continued. The total quantity of products returned since the policy was commenced in 1929 now amounts to approximately 30 million barrels. Haft Kel Field.—The drilling of the main Haft Kel structure for production purposes has now been completed. Production and control wells have been completed to meet the rate of production anticipated over the next few years.

Jan 1, 1937

By Charles M. Rolker

THIS remarkable and well-known district lies about 320 miles south of Salt Lake City, in Washington County, near the Arizona border of the territory. It is now reached by the Utah Southern Railroad and its extension, and the last 100 miles are run by stages. These vehicles are called "jerkies" in the West, which name conveys a good idea of the comfort they afford, and the relief experienced when you alight. Arriving at Silver Reef, the main camp of the district, one sees at once that he stands where once a surging sea had its domain, marked now by heavy sandstone deposits of a red and white color. The town itself, a neat, clean, and orderly mining town, is encircled on the north by traohyte and granite mountains, skirting to the west. They are cut through in places by deep gorges, left us as the only trace of the force of former currents, which drained the adjoining territory to the north; and which when swelled and infuriated by tempests and cloud-bursts, took in their grasp the huge blocks of

Jan 1, 1881

By D. M. Hausen

The amenability of a given vanadium ore to any given treatment depends largely on the mineralogic combinations of vanadium in the ore. Quantitative data on vanadium mineralogy provide not only an objective basis for selection of proper treatment, but also may eliminate many time-consuming amenability studies whose results are empirical, at best. Vanadium is distributed through the interstices of mineralized sandstone ores in the form of oxidized vanadates, reduced oxides, and silicates. Oxidized vanadates, e.g., carnotite, tyuyamunite, etc., are most readily beneficiated by simple acid leaching. Reduced oxides are more slowly solubilized, but relatively amenable to most acid treatments. The layered silicates, roscoelite, mixed layered mica-montmorillonite, and chlorite, are least amenable to most acid extractions, and constitute an assemblage of vanadium- bearing clays that are common to many sedimentary deposits. Vanadium is combined principally as layered silicates in the clay fractions of many sandstone ores. Mineralogic studies in this paper are largely confined to clay minerals, and to their amenability characteristics in low pH liquors.

Jan 1, 1985

By James A. Barr

PUMICE and pumice are varieties of volcanic ejecta formed from lavas of the more silicic types. Chemical analyses of pumice, pumicite and perlite, from which synthetic pumice is now produced, will generally fall within the limits 65 to 75 pct silica, 9 to 20 pct alumina, less than 8 pct combined alkalies (sodium and potassium oxides), less than 3 pct calcium and magnesium oxide, less than 3 pct iron oxide, with smaller amounts of manganese, titanium, phosphorus and other oxides. Perlite is characterized chemically by having, in addition to the percentages of oxides given above, as high as 6 pct combined water. PROPERTIES Pumice is a natural silicic foam glass produced by volcanic eruptions. The molten glass foam, upon rapid cooling, trapped the steam and volcanic gases that caused it to remain extremely porous and vesicular in structure. Pumice is found in the form of large lumps several cubic feet in volume and also in grains only a few millimeters in diameter. Chemically, pumicite is of the same range of composition as pumice. The distinction between pumice and pumicite is one of particle size; the coarser materials are pumice; the fine particles, an appreciable percentage of which is in the range of 100 to 325-mesh or finer, are pumicite. If the erupting volcano ejects a silicic lava containing much gas and water vapor, the sudden release of pressure tends to free the gas. The viscosity of the lava, its rate of cooling and the amount of gas evolved, all have part in determining the degree of expansion of the glassy particles and the fineness of the vesicle. If the lava is of the correct viscosity and there is not too much gas, a pumice may be formed. Large amounts of gas may cause complete disruption into pumicite.30 In 1916, Barbour gave the name "pumicite" to the volcanic ash of Nebraska and since then the name has been widely used in industrial circles for the finer-grained commercial varieties. The glass of pumice and pumicite is transparent and colorless. It

Jan 1, 1949

Jan 1, 1933

By B. M. Larsen, T. E. Brower

IN two previous papersl,2 dealing with the carbon-oxygen reaction, and the simultaneous content of each, in liquid steel in the furnace, we have made use of the quantity 0[O], defined as the excess oxygen beyond what would be in equilibrium with carbon then present if the pressure of carbon monoxide were I atm,; that is, if [C] X [O] is taken as 0.00222, 0[O] = [O] - 0,00222/[C] where [O] is the percentage of oxygen by weight as measured by the method described earlier.' This quantity 0[O] proves to be substantially independent of carbon content over the range 0.08 to 1.2 per cent, as well as of the basicity of the slag, and is nearly always within the limits 0.015 to 0.025 per cent when the bath is boiling normally and is in what we have termed a steady state. Apparently it must be at least about 0.014 per cent before boiling occurs; but this threshold value seems to depend upon the ease of bubble formation at the metal-hearth interface, hence upon the condition of the surface of the hearth. In any case, 0[O], on the average, changes considerably following any disturbance of the bath, as by addition of ore. The present paper deals with the average changes in ?[O] level following addition of Spiegel or crop ends, or after procedures to promote stirring, or by tapping of the steel from the furnace. The observations were made on a large number of commercial heats, and consequently are subject to the influence of various disturbing factors; the results have the compensating merit of showing the consistency obtainable under the limitations imposed by practical operation. VARIABILITY OF EXCESS OXYGEN IN NORMAL OPEN-HEARTH OPERATION The preceding general statements refer to the average value of ?[O] particularly in heats that are boiling actively; on individual heats, which are less active, there may be a variable time lag between the disturbance and its effect, which complicates the interpretation of what is going on. For instance, if in the normal refining process boiling is sluggish, the slag usually is gaining oxygen from the gas phase above it, or from added ore, faster than it is losing oxygen to the metal; yet when the bath starts to boil vigorously, the opposite condition may prevail for some time. The consequence of this lag is a variation of ?[O], the interpretation of which in a single heat may not be immediately obvious, This condition is illustrated in Figs. I and 2. In Fig, I, ?[O] at the beginning of the test period was near the lower limit of its usual range (dashed lines) in the steady state as a consequence of the lime boil, which had ended about as indicated. The bath is now cold, carbon drop is slow, and the first small ore feed causes only a small rise in 0[O]; as the temperature rises and as lime dissolves in the slag, and the bath becomes more active, the

Jan 1, 1946

By William Romanoff

As you are no doubt aware, virgin copper, tin and zinc are strategic metals today and little, if any, is available in the manufacture of brass and bronze ingots. The source of alloys used in the manufacture of implements of war are, therefore, from ingots made almost exclusively from the refining of available scrap. It is amusing to hear of the unusual physical properties of various alloys because they mean nothing unless the foundryman is able to produce good sound castings. A discussion therefore means little unless something is said about the relative foundry practice of the various brass and bronze alloys. Among the factors that influence the quality of castings produced are: (I) improper gating, (2) wrong pouring temperatures, (3) poor sand conditions, (4) bad melting practice, (5) faulty pattern equipment, (6) metal. It seems to be the consensus of opinion that about 95 per cent of defective castings can be attributed to the first three causes. Metal while a source of trouble at times, is probably the least responsible for foundry difficulties. As you all know, a molder never makes a bad mold. His first thought is to blame the "damn" metal as this is the path of least resistance. Let's consider the "damn" metal and how it is made. In the manufacture of ingot, scrap is collected at various sources and is shipped to the refiner either directly or through the scrap dealer or broker. It is usually sorted, although not always. In working toward a specified chemical analysis, weighed amounts of various grades of scrap metals are melted, and then oxidized by blowing air through the molten bath to rid the metal of detrimental impurities or reduce them to within specification limits after which they are skimmed off with the aid of some added fluxes. The bath of metal is then poled with wood, chemically tested before and after additions are made to bring it up to required specifications, and finally poured into ingots, after which a final chemical and physical examination is made. As mentioned above, the impurities have either been eliminated or reduced to the point where they meet the specifications of all Government Agencies or Technical Societies. Therefore, why worry as to whether castings are to be made from strategic virgin metals or secondary ingots from available scrap. Tests have continuously been made and it is a proven fact that physical properties are no better from virgin metals than from secondary ingots of the same composition. It is definitely more fool-proof to make castings from secondary ingot than from virgin metals because if an error is made in weighing the copper, tin, lead or zinc of the latter, the analysis is off balance. If an error is made in weighing secondary ingots, you merely have more or less metal but the analysis remains constant. Furthermore, when pure copper is melted. it is susceptible to reducing gases as well as oxides. Secondary ingot is already alloyed with natural deoxidizers such as zinc, etc., and the volatilization of the latter also tends to eliminate reducing gases mechanically.

Jan 1, 1943

By Henry Rogatz, H. W. McCue

Oil.—In the Texas Panhandle, 502 oil wells were drilled during the year 1940, with a total daily initial production of 139,187 bb1.—that is, 137 more oil wells drilled than in the previous year, with an increase in total daily initial production of 8219 bbl. The total daily potential of the field on Dec. 31, 1940, as determined by the Texas Railroad Commission, was 1,375,502 bbl., an increase of 30,825 bbl. over the previous year. On Dec. 31,1940, a daily allowable of 85,050 bbl., which was a decrease of 35 per cent over 1939, was assigned to the field to be produced from 4788 wells. The total amount of oil produced for the year was 26,788,590 bbl., making a cumulative total of 378,960,728 bbl. during the past 19 years. No new oil-producing acreage was discovered. Gas.—During the year, 92 gas wells were drilled, having a combined open flow of 2,402,900.000 CU. ft.; that is, 6 more than the number of wells drilled in 1939, with an increase in the open flow of 204,900,000 cu. ft. per day. The gas production for the year was 670,435,112,000 CU. ft., and the total gas removed from thc ground during

Jan 1, 1941

By J. C. Landenberger

Freezeproofing waste dump cars during winter months has long been of concern at Kennecott's Utah Copper Div. open pit property. Waste mining operations at Bingham Canyon use trains of seven 40-cu yd side-dump railroad cars with electric locomotives to service stripping shovels. Waste is transported an average of nearly 3 miles from the mine benches to dumping areas. During winter months, usually beginning in late October or early November, intermittent and continued periods of freezing together with varying amounts of snow cause waste material to freeze or stick to the sides and bottoms of the cars. Because of the physical layout of the pit, it is not feasible to freezeproof all waste trains at one or even a limited number of locations. A waste haulage line usually serves one or two mine benches, so that freezeproofing facilities must be maintained at many locations. For example, at the time of writing 27 salting stations were in use.

Nov 1, 1955

For the year ending February, 1920 PRESIDENT HORACE V. WINCHELL MINNEAPOLIS, MINN PAST PRESIDENTS PHILIP N. MOORE ST. Louis, Mo. SIDNEY J. JENNINGS NEW YORK, N. Y. FIRST VICE-PRESIDENT A. R. LEDOUX NEW YORK, N. Y. TREASURER GEORGE D. BARRON NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 4, 1919

Jan 1, 1934

W. H. Blauvelt, New York, N. Y.—One thought lias been running through my mind during the wholc of this meeting and that is that the scientific and the practical men must recognize very clearly their interdependence. The value of scientific classification of coal is going to be of the very greatest importance to the users, the practical men. Is not the scientific investigation and the great amount of work that is being done in a measure at least lost to the world? Therefore the scientific investigations and the practical needs of the users should bo brought as close together, and the work should be done as closely together, as possible; that is, the scientific man should know what the practical man needs, and the practical man should not feel that the scientific man is merely a theorist. Scientific investigation is going to have a great effeet and be of great valuc to the practical man who is trying to solve his problems. In the subject which I discussed' for instance, we must look to the scientific man to tell us why coal cokes in one way and not In another and why certain coals will do certain things and others, which appear on the surfacc to be generally similar, do not act in the same way. Need or Physical Data on Coal H. J. Rose, Pittsburgh, Pa.—There is a subject which is a sort of hobby of mine; that is, the need for what might be called critical tables of constants for coal. The chemist has big volumes giving constants, such as the density, solubility, specific heat, thermal conductivity and all other physical and chemical data that have been determined for chemical compounds. Data arc also available on many common materials, for example, the density, hardness, modulus of rupture or maximum crushing strength of swamp white oak as compared with some other wood. In fact, physical data for practically cvery hype of wood commercially produced in the world can he found. In the same way the metallurgical man has handbooks giving the properties of alloys, etc., but we havc very little tabulated information about coal. Our principal reference works are the volumes published by the U. S. Bureau of Mines on the proximatc and ultimate analysis and calorific values of coals of the United States. That is 3 pioncer work of enormous value, but we have reached the point where we need more diversified information. Mr. Fulweiler raised the question of the relative strength of the different coals and cokes. Dr. Campbell and Dr. Ashley wanted to have some information on the resistance of coal to air slacking. It was brought out in the discussion that we want to know something about the coking properties of coal. There are any number of physical tests that we need, such as the thermal conductivity of certain coals, the coefficient of expansion, or the coefficient of friction; or other constants. A smattering of such information is scattered through the literature; for instance, a research worker in Wales will report a coefficient of expansion on Wclsh coals and one in South Africa will report something else for one or two kinds of African coals, hut it is difficult to find the information that is needed on our own coals. Would it not be worth while to consider collecting reliable critical

Jan 1, 1930

By E. P. Klier, V. Weiss

IN studies of the X-ray diffraction line geometry of iron with chromium radiation using techniques aimed at minimizing the background intensity, Kp and Ka emission satellites* were resolved with three techniques. These satellite lines are present with sufficient intensity to lead potentially to erroneous structure analysis, if not properly interpreted. The techniques used were: 1) film technique with un-filtered radiation and polycrystalline specimen, 2) film technique with unfiltered radiation and single crystal, and 3) counter technique with unfiltered radiation and single crystal. An example of results obtained with technique 1 is given in Fig. 1.

Jan 1, 1958

By P. Marier, T. R. lngraham

The kinetics of the sulfation of MnO,, MnzO3, and Mn3O4 in SO,, SO3, and O, mixtures was examined and the descending order of sulfation rates at temperatures near 400°C was found to be Mn,O3 > MnO, > Mn3O4. The respective activation energies for the thermal decomposition of MnO, and Mn,O, are 39 and 47 kcal. At 900°C, the thernzal decomposition of MnSO, to MnzO3 is slower than that to Mn3O4. The respective activation energies are 62 and 51 kcal, respectitely. MANGANESE is used to improve the hot workability of steel in the proportions of approximately 13.5 Ib of ferromanganese per ton of steel produced. This requirement accounts for about 95 pct of its large industrial market in North America. The remaining 5 pct is used in the battery and chemical industries. In most North American ores, the percentage of manganese and the manganese-to-iron ratio are not suitable for the direct production of ferromanganese. Hence, most of the North American requirements for manganese are satisfied by importing ore. Typically, many of the studies done on native low-grade manganese resources have been directed toward the production of ore substittes" and the recovery of manganese from open-hearth slags.3 Of the wide variety of processes which have been proposed, the most popular involve compounds in the Mn-S-O system. The thermodynamic properties of manganese and its compounds were reviewed by ah' in 1960 and, more recently, lngrahams discussed the thermodynamics of some of the reactions involved in the Mn-S-O system at normal roasting temperatures. The conditions for producing manganese sulfide during the reduction roasting of manganese sulfate are discussed by Fuller and Edlund.9 A novel scheme was proposed recently by zimmerley7 for utilizing waste sulfur dioxide from stack gases to recover the manganese from ocean-mined manganese nodules. Very little of the work published on manganese compounds has been related to reaction rates. Singleton et 1.' studied the rates of reaction on the MnO-C and Mn7C3-3MnO systems and observed linear and parabolic kinetics respectively in the systems. Tatievskaya et a1.' studied the low-temperature reduction of Mn&, MnO,, and Mn& in HZ and CO, and reported activation energies in the range 1628 kcal. In this paper, the rates of some of the decomposition and formation reactions involving MnSO4, MnOz, MnzO3, and Mn3O4 will be examined after the conditions for the thermodynamic stability of the individual compounds have been designated. CONDITIONS FOR STABILITY OF MnSO4, MnOz, MnZO3, AND Mn3O4 The areas of stability for h'hSO4, MnOz, MnzO3, and h3O4 were established from the data of Mah4 and Ingrahams and are shown in the predominance area diagram,10 logpq- logpsq, in Fig. 1. The diagram is drawn for two temperatures, 700°K, solid lines, and 1100°K, dotted lines. The sketch for the lower temperature includes the conditions likely to prevail in the Zimmerley patent7 when manganese nodules react with sulfur dioxide and that for the higher temperature indicates the conditions for recovering MnzO3 or Mn3O4 from MnSO4 during a roasting reaction. From the fact that the boundary between the areas of stability of MnOz and hSO4 at 700°K is parallel to the abscissa, it is evident that MnOz and SO2 should react together to produce MnSO4, irrespective of the oxygen pressure in the system. If the source of sulfur for sulfation were from waste flue gases, it is likely that the oxygen content of the gas stream would be more than sufficient to oxidize any MnsO4 to MnzO3, 107 atm of O2 required, or even to convert any Mnz03 to MnOz, 0.02 atm OZ required, prior to sulfation. At 1100°K, the diagram indicates that MnSO4 may be converted directly to either MnzO3 of Mn3O4, depending upon the prevailing partial pressure of oxygen. When the gas stream contains more than 1 pct Oz, logpq = -2, only MnzO3 would be recovered from an experiment done under equilibrium conditions. At oxygen partial pressures of less than 1 pct, one would expect to bring about a reversible exchange between MnSO4 and Mn3O4 by appropriate adjustment of the partial pressure of SOZ. These various reactions will be described in the subsequent kinetic experiments.

Jan 1, 1969

By Arthur B. Yates

Diamond drilling has advanced and expanded during the past few yean. Along with this increase there has been a marked trend to rely more and more upon drilling for the outlining of ore for reserve purposes. This is especially true underground, where men have not been available for opening up ore by crosscuts, drifts and raises. During the recent heavy call upon known ore reserves, more drilling has been done for exploration and it has become expedient to drill longer lateral holes from underground and deeper holes both from surface and from exploration headings in the mines. Furthermore, these deeper holes have to be drilled closely enough to warrant calculation of "probable" if not "proven" ore, from the results obtained therefrom. Interpretation of diamond-drill results has become more precise and reliable with the growing knowledge and understanding of the geologic structures that control the geometry of ore distribution, and this has broadened the field of usefulness of the drill. All of this has created a necessity and a demand for more accurate control of the hole as to direction, a more precise and reliable method of surveying for position, and a need for better and more complete core recovery, as well as larger cores, to provide an adequate sample. At depth the control becomes more difficult and, at the same time, more important. Control A close study of drilling in various parts of the world for a period of more than 20 years has brought to light one definite rule, practically invariable; namely, that diamond-drill holes tend to deviate into a position normal to any structure existing in the rocks, such as bedding, schistosity, gneissosity, or even parting or jointing— even if the hole is started at almost any angle other than parallel with the structure. It also appears that the better developed the structure is, the more quickly will the hole get into a position perpendicular to it. It has often been said that there is a tendency for holes to "drift" in the direction of rotation. This is obviously untrue, for in a vertical hole the measure of deviation would depend upon the azimuth chosen as zero, and there is an infinite number of choices. It has been proved. however, that in homogeneous rocks there is a tendency for the hole to corkscrew, and that the direction of the spiral is the same as the direction of rotation. This may account for the belief that holes drift in that direction. Some tests have been made using right-hand and left-hand rods, and these show that no matter what the direction of rotation the hole will swing into a position perpendicular to the structure. Methods of Control The foregoing empirical rule may be used as an indirect method of control. If the prevailing structure is known, it may be advantageous to start the hole as nearly normal to it as possible, for the

Jan 1, 1946