Search Documents

It is interesting to note that during the period that has elapsed since the Institute's formation, wood charcoal, anthracite and bituminous coal, as well as beehive and by-product coke, have been used as blast-furnace fuels, that the reign of supremacy of each fuel was associated with specific periods, and that each successive era was marked by a production of pig iron greater in quantity than the one it followed (Fig 1). The transition of the manufacture of blast-furnace iron from charcoal to anthracite and then to beehive coke, and ultimately to by-product coke, is a reflection of the economic limitations of each fuel coupled with availability sufficient to meet the increased demands of each succeeding decade. It is a pattern that has been followed almost without exception in the history of pig iron in every country. CHARCOAL Colonial production of iron relied exclusively on wood char- coal as a fuel, and the iron industry of this count recognizes the important role played by this fuel. Charcoal iron has been available to consumers since the beginning of the organized iron industry in America in 1645, by John Winthrop at Saugus, Mass.,1 and although its greatest use antedates the formation of the Institute, it is still used to some extent. Until about 1840 nearly all of the pig iron manufactured in the United States was made with charcoal, and it continued as a principal smelting fuel until 1855.2 After that time, more pig iron was produced with other fuels, despite the fact that

Jan 1, 1948

By Walter Kauenhowen

GeRmany's crude-oil production during 1936 totaled 3,112,494 bbl., an increase of 5.2 per cent over the 3,007,711 bbl. produced in 1935. The official monthly production figures published in 1936 report only the individual production figures of the three old established fields, whereas since 1936 official reports combine the production of all other fields into one figure. According to these published data, and using a conversion factor of 1 metric ton equaling 7 bbl., the oil production of Germany in 1936 was as follows:

Jan 1, 1937

By Oswald J. Heinrich

AT the Baltimore meeting of the Institute in February, 1879, Mr. Eckley B. Coxe, then president of the Institute, called attention in his address to the subject of Secondary Technical Education, and

Jan 1, 1881

By J. Ellzey Hayden

THE Cliffs Shaft mine of the Cleveland Cliffs Iron Co., located in the city of Ishpeming, Mich., is the largest producer of hard hematite ore on the Marquette iron range. The two shafts, A and B, lying 820 ft. (250 m.) apart on the east-west trend of the ore formation, were sunk in the early eighties, and, except for four years, have been steady producers of iron ore. Their location, on a hill overlooking the general offices of the company on the one side and the city of Ishpeming on the other, has made the shaft houses landmarks. In the spring of 1919, as the old wooden shaft houses had become shaky and out of line, and would soon be unsafe, it was necessary to replace them with the least possible delay. Three plans of construction were, therefore, considered: To replace the old shaft houses by somewhat similar structures made of wood; to use steel and radically change the design; or to build reinforced-concrete shaft houses outside of the wooden structures, completely enclosing them. The first plan was disapproved, because it is anticipated that the mine will have a long life and the proximity of other buildings makes the danger from fire rather great. Delay in receiving material, and the necessity for closing the shafts during erection, were other factors in the situation. The second plan was disapproved on account of the high cost of steel, slow delivery, and interference with hoisting during the period of erection. The presence near one of the shafts of a large bed of hard gravel suitable for concrete made, the cost of the third plan considerably less than the second, and little, if any, delay in hoisting was expected. Our expectations in this regard' were fully realized. Furthermore, the work could be done by unskilled labor, which was plentiful, and the erection could be quickly started. When the proposition was submitted to Mr. W. G. Mather, president of the company, he recommended that, on account of the prominence of the buildings due to their location, an effort should be made to combine in the design as far as practicable something of architectural beauty. Following his recommendation, the original plans were submitted to the

Jan 8, 1920

By W. F. Chiao, R. B. Gordon

Tile sharp-yield point found in magnesium crystals in the solulion-treated and aged condition is studied by dislocation internal-friction experiments. The results show that the sharp yield is not file to the sudden release of pinned dislocations hut is movc likely due to the rapid multiplication of an initially small number of dislocations. Recovery or the dislocation internal friction after deformation is also studied. This yecovery results from the re-pinning of dislocations by a solute, presumably nitrogen, which moves with a relatively small activation energy. SHARP-yield points, when they occur, are a striking feature of the stress-strain curve generated during a tensile test. Although commonly associated with steel, sharp yielding has been found in a variety of metallic and nonmetallic crystalline materials. In particular, sharp-yield points have been found in zinc"' and cadmium3 containing nitrogen. With this background, Geiselman and Guy4 investigated the tensile properties of magnesium single crystals containing nitrogen to see if sharp yielding also occurs in this system. They found that sharp yields did indeed occur in solution-treated and aged specimens tested at elevated temperature but were not able to give conclusive proof that the sharp yield was caused by nitrogen, a yield drop being observed even in their purest crystals. Sharp-yield points have also been found in various polycrystalline magnesium alloys.7'8 In the study of the sharp-yield phenomenon it is desired to observe the behavior of dislocations in the earliest stages of the deformation process. Internal-friction experiments are useful for this purpose because dislocation damping is sensitive to the mobility of free-dislocation segments. At low strain amplitudes the damping, A, due to the the forced vibration of dislocation segments of average length L is ? =KAL4 [1] where A is the dislocation density and K, if the applied frequency is well below the resonant frequency of the dislocation segments? is a constant for the sample under observation.5 Dislocation damping, because of the fourth-power dependence on L, is particularly sensitive to the creation of free-dislocation segments during deformation. Since sharp yielding is associated with the sudden release of pinned-dislocation segments, marked changes in the dislocation damping are expected at the yield point.6 The use of the dislocation-damping observations to help elucidate the incompletely understood mechanism of yielding in magnesium is the primary objective of the experiments reported here. PROCEDURE Many investigations have shown that very marked and rapid changes occur in the dislocation damping of of a deformed material as soon as the straining is stopped.5 It was quite essential, then, for the purpose of this investigation, to make the damping measurements during the deformation of the samples. This can only be accomplished through the use of the ultrasonic-pulse method. In this method traveling sound-wave pulses are used and, in contrast to resonating-bar methods, only the sample ends are set in vibration. Thus, the sample can be gripped along its sides in the tensile-test machine without disturbing the damping measurements. In the pulse method, the decrease in the amplitude of a sound pulse is measured as it travels back and forth through the sample. If A is the amplitude after traversing a distance x and A. is the initial amplitude, A=Aoe-ax [2] and a is called the attenuation. It is commonly measured either in units of cm-I or as db per µ sec. The observed attenuation in a metal sample is due to a number of causes. These include scattering by grain boundaries and impurity particles, thermo-elastic damping, diffraction effects, stress-induced ordering of solute atoms, and dislocation damping. The total observed attenuation in a given sample usually cannot be resolved into these various components, but changes in a due solely to changes in dislocation damping can be accurately determined, provided the experiment is arranged so that all other sources of damping are held constant. It is desired to reduce the extraneous sources of attenuation to a minimum and for this reason the experiments are done on single crystals of high purity. Magnesium crystals offer the further advantage that, when properly oriented, only a single set of slip planes is active during deformation. Crystal Preparation. The method of sample preparation is similar to that of Geiselman and Guy.4 The starting material was high-purity, sublimed magnesium rod supplied by the Dow Chemical Co. Melting under Dow 310 flux was used to reduce the nitrogen content of the starting material: the fluxing was done under an argon atmosphere and the

Jan 1, 1965

The three papers following describe and discuss methods and results of sampling copper ore in disseminated deposits, in limestone replacement and contact metamorphic orebodies, and in replacements of limestone, porphyry, and contact breccia.

Jan 1, 1925

By K. P. Gupta, P. A. Beck, N. S. Rajan

By determining the a phase boundaries in the following ternary systems: V-Fe-Si (at 1175oC), V-Co-Si (at 1175°C), V-Ni-Si (at 1175oC), Cr-Mn-Si (at 1000°C), Cr-Co-Si (at 1175°C), Cr-Ni-Si (at 1175°C), V-Fe-A1 (at 1175°C) and Cr-Co-A1 (at 1175°C), it was found that Si exerts a stabilizing effect on these a phases, while A1 tends to destabilize them. Si atoms in solid solution occupy sites D in the a structure, The co/ao ratio increases with increasing Si-, Mn- or Fe-content. The volume of the unit cell decreases with increasing Si-content. THE stabilization of certain metal silicides (the Nowotny phases) by the addition of relatively small

Jan 1, 1961

By Michael P. Richardson

INTRODUCTION This paper is intended to be a summation of the state-of-the-art i n draw theory and draw- point spacing. Knowledge of this very important factor in the successful design and operation of a block caving mine is scarce and nonconclusive. It is hoped that the presentation of this paper will stimulate interest and discussion which will lead to a stronger understanding of these a1 1 important factors. Please note that block caving as used here- in refers to block, panel, and mass caving systems in general, not just to the specific system of block caving where discrete blocks of ore are prepared and caved as a unit. DRAW THEORY The knowledge of draw theory as related to the practice of block caving mines is, unfortunately, very limited. In recent years much work in draw theory has been done in respect to sublevel caving systems and an understanding of draw mechanics relating to sublevel caving seems to be emerging. This work is certainly helpful to those of us interested in block caving but the question of "what goes on up above" still hounds us since we are more interested in the region of draw which begins just above the area where sublevel caving interest ends. Herein is presented a brief summary of draw theory with an attempt to look at the factors which can help our understanding of the area of draw influence in block caving mines. Nature of Gravity Flow An understanding of the flow of granular material (rock, sand, grain, or prill as examples) is the first step toward understanding block caving draw. If we take a supported column of granular material and allow gravity flow through an aperture at the bottom of the column, an ellipsoidal shaped zone of disturbance of the in-place material will form and grow with extraction of material through the aperture. The volume of this zone of disturbance or loosening is about 15 times the volume of material extracted at any given time (Kvapil, 1980). Figure 1 shows the development over time of the zone of disturbance. The ellipsoid of disturbance represents a future ellipsoid of extraction which will equate to the volume of materia1 extracted by that future time. Extraction involves the movement of the particles located vertically over the drawhole directly downward while material outside this direct vertical volume moves radially inward and down toward the drawpoint as shown in Figure 2a. Figure 2b shows the result of this motion on originally horizontal strata within the ore column. Increased draw increases the eccentricity of the ellipsoidal volume or, in other words, the ratio of the height over the width of the disturbed area increases as ore is withdrawn from the column (Kvapil , 1980). This becomes important to block caving since eventually a vertical cylinder of draw will be approximated as this ratio increases without bounds. Figure 3 shows this result. The width of this draw cylinder is a critical dimension for the determination of draw point spacing in relationship to block caving mine design. McCormick (1968) for one, felt that within this cylinder of draw, mass flow would take place. This is the

Jan 1, 1981

Jan 1, 1967

By F. W. Jr. Sperr

THE byproduct coke oven is the most important artificial source of fuels for metals melting. Its products are solid, liquid, and gaseous in form. The amount of coke and primary byproducts obtained per ton of coal varies with the nature of the coal. The following represents the results obtained in many plants: Metallurgical coke (over 3/4 in.) 69 per cent. of coal Domestic coke (1/2 to 3/4 in.) 2 per cent. of coal Breeze (under 1/2 in.) 4 per cent. of coal Surplus gas, cubic feet per net ton 6600 Gas for heating ovens, cubic feet per net ton 4400 Tar, gallons per net ton 9 Ammonium sulfate, pounds per net ton 25 Benzols, gallons per net ton 4 All of these products, except ammonium sulfate, have important fuel value. Part or all of the metallurgical coke may be crushed or screened to furnish additional domestic coke. If producer gas is used, there will be a surplus of 11,000 cu. ft. of coke-oven gas per net ton of coal. The use of coke in the metallurgical industries has been retarded by the mental attitude of writers who disregard the dependence of coke quality on the conditions of its manufacture. Terms like "byproduct coke,"' "beehive coke," "48-hour coke," and "72-hour coke" are only generally descriptive and tell nothing of the coke quality. For example, one writer1 stated that in brass-foundry practice, Connellsville coke is considered much superior to byproduct coke on account of the high sulfur content of the latter. Another2 says, "At equal prices for hard Connellsville coke and for byproduct coke at the foundry door, the hard coke is unquestionably cheaper. It will melt more metal per ton than the byproduct coke and requires less labor, as the byproduct coke is less dense and burns faster, thus requiring more frequent firing." A little study of the conditions under which coke is manufactured will show the error in mak-

Jan 10, 1920

By H. H. Lowry

Science attracts the attention and interest of an individual or an industry in general only in proportion to the apparent direct application to its immediate welfare or benefit. Engineering accomplishments, as aphlied science, therefore receive more recognition than the scientific discoveries on which they are based. Even self-evident truth needs endless repetition before recognition: engineering as applied science cannot advance beyond the science on which it is founded. Scientific research, and discovery, is sometimes forced by the limitations recognized by those active in its development for the use of society and industry and sometimes results from an apparently superficially illogical curiosity about natural phenomena. Research has received inadequate support except in industries born in the laboratory, the chemical and electrical industries, from which many lessons might well be drawn by their elder associates. The rapid growth of these industries has been largely due to close cooperation of scientists and engineers. Most rapid advance is made when the research worker and the engineer keep in close touch with each other's ideas and problems. Many of the developments of modern industry are based on discoveries buried for years in scientific journals because the "time was not ripe" at their discovery. The situation with regard to utilization of coal is quite the oppositre. The fundamental facts in regard to the scientific aspects of the problem of developing the energy from coal are scarcely known. The engineer, without much scientific cooperation, has accomplished much in increasing the number of kilowatt-hours per pound of coal from 0.31 in 1919 to 0.69 in 1934, in increasing the 1000 gross ton-miles of freight hauled from 12.2 to 16.4 per ton of coal in the same period, in fuel economy in production of coke, and in developing the production of motor fuel in Germany and England by hydrogenation of coal. This lack of scientific research on the utilization of our most important natural resource, coal, has been due undoubtedly in large part to the reluctance of investigators to study the interrelationships involved in the complicated processes in which coal is used. These complexities are made

Jan 1, 1936

By Gunnar Thaning, Borje Bjorkvall

At LKAB Central Division for Metallurgical Research at Malmberget, Sweden, fired pellets are examined in respect to mechanical and reduction properties. The paper deals with descriptions of the test methods. It also involves the rationale for the choice of these tests. Their correlation to the blast furnace operation will be examined. The mechanical tests used are the ISO-tumbler test and the cold compression strength test. Concerning the metallurgical properties, experiments have shown that some superbasic pellets in particular have different disintegration properties in different temperature ranges. Pellets which have favorable reduction properties when tested under isothermal reduction at high temperature may disintegrate to a large extent under low temperature reduction. This is also valid for some types of acid pellets. Consequently, it was found to be necessary to determine the reduction strength both at high and low temperatures. In the low temperature range, the disintegration is measured by tumbling the pellets in soft reducing conditions at 600°C in a modified Linder test equipment. The high temperature reduction strength is determined under load in the Burghardt-Grebe equipment. However, in order to get more information of the high temperature strength, LKAB intends to introduce a softening test. The tendency of high temperature disintegration will also turn up in the swelling test. The swelling properties are examined according to a procedure developed at LKAB. In this test the pellets are subjected to free swelling without mutual contact. The reducibility of the pellets is recorded in the swelling test.

Jan 1, 1974

By Arthur Phillips

DURING the past few years considerable interest has been shown in the study of fiber, and its effect, in wrought metals. Fiber has recently been defined as a "condition of parallelism of important lines or details in the structure. "1 Briefly stated, two distinct types of fiber are commonly encountered. One results from the alignment in the direction of working of constituents, more or less segregated, such as slag, oxides, carbides and dendritic formations. The second, and least understood, type is produced by working the metal below the recrystallization temperature in such a way as to develop a parallelism of the grains. This condition is readily recognized by the pronounced elongation of the grains in the direction of working. Under certain deformational treatments the grain fragments produced by cold working tend to orient in certain definite directions with respect to the axis of extension. Furthermore, even in metals that have been annealed after cold working preferred orientations may be present. It is perhaps logical to assume that such marked parallelism of structural elements would be manifested by directional properties in the metal. As a matter of fact, tests on many kinds of materials have shown differences in varying degrees. In recognition of this condition, propel design, for many purposes, places the fiber axis in such a way as to present the direction of maximum strength to the greatest applied stress.

Jan 1, 1931

Jan 1, 1917

By Arthur Tauber, Horst Kedesdy

FERRITES are sintered metallic oxides of the spinel structure type1 and belong to the class of soft ferromagnetic materials. Similar to a ceramic, they can be formed and fired to a dense body, exhibiting a high electrical volume resistivity ranging from 102to 107 ohm-cm as compared with 10-6 ohm-cm for some of the metallic magnetic materials. This high resistivity, with resulting low eddy current losses, finds special application at high frequencies. The dispersive susceptibility of ferrites at microwave frequencies has also led to many applications in this field. Ferrites are used in low frequency applications where high resistivity with high permeability is desirable. During the last few years ferrites exhibiting rectangular hysteresis loops have been developed for computer and magnetic memory systems. The general formula for ferrites is MeFe2O4 where Me is a divalent metal ion such as Ni, Zn, Mg, Mn, Cu, Cd, and Fe. Only two of these ferrites are nonferromagnetic, namely, those with Zn and Cd. Solid solutions can be formed between different ferrites, and it is of interest to note that solid solutions of a ferromagnetic ferrite with a nonferromagnetic ferrite yield much better magnetic materials than the basic ferrite body. In general, it can be said that the solid solution formation between ferrites has widened the field of ferrite synthesis and has led to methods of preparing materials with a large variety of magnetic properties. During the last two decades the synthesis of ferromagnetic oxides has been the object of extensive research, but commercial production has been started only within the last ten years. Along with more fundamental studies, there remains the never- ending task of developing ways to realize the optimum characteristics of materials in large-scale production. Ordinarily, to produce a ferrite material it is necessary for the constituent oxides to be mixed intimately, pressed, and then fired at temperatures above 1000°C. Ferrite Synthesis: Formation of a basic ferrite by solid state reaction from Fe2O3 and a monoxide such as NiO, under normal atmospheric conditions, is governed by a progressive diffusion of cations between adjacent particles of the constituents. Firing temperature, furnace atmosphere, and cooling can vary the magnetic properties, however. If, for example, a dioxide, a sesquioxide, or an oxide of the Me3O4 type is substituted for the monoxide, the reaction mechanism becomes more complex and extremely dependent on atmospheric conditions and firing cycles. For this reason reproduction often

Jan 1, 1958

By J. A. Kitchener, J. P. Anfruns

Measurements have been made of the rate of capture of single particles of strongly hydrophobic, surface-methylated, quartz, of sizes ranging from 12 to 40 µm diam., by single rising bubbles of diam. 0.5 to 1.1mm. The results agree closely with the theoretically calculated hydrodynamic collision rates, indicating that, in this system, every collision results in capture and retention of a particle.

Jan 1, 1976

By William Kent

In the paper by Mr. Fernom, on Red Charcoal, read at the first session of this meeting, it was suggested that this fuel might be used in the blast furnace with greater economy than ordinary or black charcoal. In the discussion which followed the paper, it was stated that the charcoal furnaces of the Lake Superior District have used imperfectly burned charcoal with success, and that these furnaces have given the best results in fuel economy on record. On consulting some of our well-known metallurgical authorities the writer finds that the question of the use of red charcoal, or other imperfectly burned charcoal, or charred wood, is not at all new. In Percy's late work on Fuel, pages 409-414, are given a few facts, which are here condensed, as follows:

Jan 1, 1879

BLOCK CAVING HAS BEEN DEVELOPED to a high degree of efficiency in the last two decades and more particularly since World War II. At the Jeffrey mine of Canadian Johns-Manville Co., in the Eastern Townships of Quebec, several innovations have increased production and decreased costs. Asbestos ore is produced at the rate of 10,000 tpd from an underground operation supplemented by a large open pit that has been mined since 1881. The orebody consists of asbestos veins in a fractured and serpentinized peridotite. Hardness and structural strength of rock vary from soft shear zones at one extreme to a small amount of hard granitic inclusions at the other. In general the ore is weak and deteriorates on exposure to air, so that it is difficult to maintain underground openings for any period of time. Permanent workings are lined with concrete and temporary ones are driven mini- mum size and supported with steel sets as required.

Jan 5, 1954

THIS issue is about Chuquicamata and the new sulphide plant. Chuquicamata is moving into a new cycle of productivity; she has begun to give up the sulphide copper which lies deep-seated beneath the oxide ore zones in large but yet unknown quantity. After forty years of production, Chuqui may be likened to a strapping youngster, with adolescence and maturity still ahead. Mining operations are being projected-not for decades -but for generations. Although there are still many years of open-pit mining ahead, planning of future underground mining has been started. The bottom of the orebody is still unknown, but enough work has been done to show that Chuqui is one of the largest known copper orebodies in the world. Until recently, only the oxide ores have been mined and these have been treated at the rate of 50,000 to 60,000 tons per day by leaching. Construction of the sulphide plant was timed to coincide with reduction in production of oxide ores. The new sulphide concentrator and smelter, designed in keeping with the magnitude of the orebody, will be brought on the production line at the rate of 30,000 tons per day. The capacity of the plant now planned can be expanded to treat 60,000 tons of sulphide ore. Little wonder that Chuqui is a name legendary in the remotest mining circles. But to those who have known her more intimately, and there is hardly a mining camp without a Chuqui graduate, she means much more. She is an orebody that has made engineers. Reposing at 10,000 ft on the western flank of the Andes in the arid northern reaches of Chile, water is scarce, common fuels absent, and volcanoes and earthquakes add drama and hazard. It is these natural difficulties which have created the fascination and challenge which have caused many engineers to devote their lives to unlocking this treasure house of nature.

Jan 1, 1952