Search Documents

By R. L. Grayson, Y. J. Wang

This paper presents an application of goal programming (GP) to major mining machinery purchases based on historical operating data on mechanical downtime and production. The GP technique, an extension of integer programming, is used to maximize an objective function comprised of deviations away from management-preferred financial goals. Different capital budgeting techniques are used to evaluate capital proposals, and the results of these analyses are combined and weighted in a maximization of profits objective function. The GP method gives an optimal solution to a multiple goal problem. A sensitivity analysis is performed to determine the effect of a variable production improvement condition or a variable budget control con¬dition on proposal selection.

Jan 1, 1984

By R. Norman Orava

The strain-mte behavior of. the tensile yielding and flow characteristics of arc-cast polycrystal-line molyhdenum of pidrity > 99.97 pct was investigated in the range 10-6 to 10-1 sec-1 at 243o, 293o, and 373oK for two grain sizes, 0.027 and 9.098 mm. For 0.998 mm, the strain-mte dependence of the lower yield stress can be described by a straight line of the jowl a, = a + 0 log e over the whole range of strain rates examined. However, for 0.027 mm, the data fit several consecutive linear relationships of the above form. The previous association of these different linear regions with different rate -controlling mechanisms is questionable for molyhdenzdm. The senlilog strain-rate dependence of the yield stress is consistent with Hahn's model for yielding when the stress dependence of the mobile dislocation density, pr, is taken into account. Since p', from rate -cycling experirnents, is found to be relatively insensitive to stress for single crystaIs, the obserzied log-log dependence of their yield stresses is also in agreement with the model. A correction for the stress dependence of p' changes the activation oolurrze for yielding from a zero to a more realislic inverse function of stress where the Peierls mechanism is believed to be rate-controlling. The gmin-size dependence of the lower yield stress is not a monotonic junction of strain rate. RECENT experimental evidence' has revealed that the strain-rate dependence of the tensile lower yield stress, a,, of commercially pure ni- obium and tantalum tested at room temperature can be described by several consecutive semilog relations of the form: sv =a + ß log € [1] where i is the applied strain rate and a and 0 are constant Over only relatively small ranges of strain rate. Three linear regions were found for niobium and four for tantalum. Each linear region was interpreted as being associated with a different rate-controlling mechanism on the basis of the current

Jan 1, 1964

Jan 1, 1968

By R. W. Heckel, R. L. DeGregorio

The DeHoff method of determining the size distribution of ellipsoid-shaped, second-phase particles has been applied to the spheroidization of cementite in a eutectoid steel. The surface area of Precipitates determined from the various size fractions in the distribution was correlated with surface-area measurements based on the number of intersected interfaces on a random lest line. The precipitate particles were found to be oblate ellipsoids with an axial ratio of about 0.90. The size distributions were found to be log-normal. A method is proposed whereby the shrinkage of small particles and growth of large ones can be determined from the experimental data. The experimental data are compared to previously proposed mathematical models describing diffusion-controlled kinetics and various types of interface-controlled kinetics. The experimental growth and shrinkage rates are considerably slower than those predicted by diffusion-controlled kinetics. The best fit is obtained for a model describing interface-controlled kinetics limited by the rate of formation of cementite at the growing interfaces where the interfacial reaction rate is proportional to the solute thermodynamic activity gradient across the surface. THE subject of spheroidization of second-phase particles has been considered previously by other investigators. Livingston1 has studied the precipitation of the cobalt-rich phase from copper alloys containing 0.7 to 3.2 wt pet Co. His results indicate that the average particle size increases as the cube root of the heat treatment time in accord with diffusion-controlled kinetics.'-' Komatsu and rant' in their studies of the growth of SiO2 in a dispersion-strengthened copper-silica alloy found that the initial growth of SiO2 proceeded by diffusion-controlled growth and later stages were limited by interface-controlled growth. The values of the activation energy obtained for the interface- controlled process led them to the conclusion that the process was limited by the dissociation of SiO2 at the shrinking interface. The transition from diffusion-controlled growth to interface-controlled growth was characterized by a particle size which varied with the heat-treatment temperature. It is also interesting to note that the particle-size distribution as found by Komatsu and Grant exhibits log-normal behavior when replotted on log-probability coordinates. Dromsky, Lenel, and Ansell9 have observed the growth of Al2O3 particles having a mean free path of about 1.5 to 13 µ. Their photomicrographs indicate that the Al2O3 particle sizes were larger than those observed by Komatsu and Grant. Dromsky, Lenel, and Ansell concluded that the Al2O3 coarsened by an interface-controlled growth mechanism limited by the solution of A12O3 at the shrinking interfaces. Bannyh, Modin, and Modin10 have studied the spheroidization of a eutectoid steel (0.83 wt pet C). Their spheroidization (tempering) treatments were carried out in the range from 210o to 700°C for times between 1.5 sec and 20 hr. Measurements of mean particle size as a function of time indicated a cube root of time dependence of size at 700°C, in agreement with previous analyses of diffusion-controlled kinetics.2°7 At lower temperatures, the time dependence was less than the one-third power. It is important to note that, although mathematical models of growth* considering particle-size distribution have been available, measurements of only mean particle size have been carried out. DeHoff11 has presented a quantitative metallography technique which is applicable to the determination of the size distribution of ellipsoids of constant shape. This method is applicable to both oblate and prolate ellipsoids of all ratios of minor to major axis and is based upon an extension of Saltykov's analysis12 of the distribution of spheres of varying size. DeHoff's analysis is based upon measurements of the minor axis of the particles on a random plane of polish in a unit area. This method provides a measure of the number of ellipsoids in various size ranges per unit area. As pointed out by DeHoff, such measurements may be used to obtain surface area and total precipitate volume data. Thus, the accuracy of the distribution analysis may be checked by comparison of the surface and volume

Jan 1, 1965

Jan 1, 1881

By M. Hansen, C. C. Wang

THE 6 phase of the Cu-Sn system (Cu,Sn, = 32.53 pct Sn) was considered to be stable down to room temperature until Owen and Iball showed by X-ray analysis that it undergoes a eutectoid decomposition into the a and e phases at a temperature near 300°C. Their findings have been confirmed by other investigators,2-5 a11 of whom used X-ray diffraction studies of powdered specimens. The transformation temperature has been reported by various authors as lying between 300" and 380°C. To our knowledge, no microscopic evidence of the eutectoid reaction has been published, as yet. It was in connection with other work that longtime annealings at 300°C were conducted with alloys containing 22, 32.6, and 35 pct Sn (nominal compositions) prepared from electrolytic copper and electrolytic tin and cast in a small iron mold. The specimens were first annealed at 700°C for 5½ hr and quenched from 400 °C after cooling to, and annealing at, that temperature for 9½ hr. After this treatment the sample with 22 pct Sn was cold worked for 15 pct reduction in thickness; the 32.6 and 35 pct alloys were too brittle to be cold worked. The final anneal at 300°C was done in a sealed pyrex glass bulb for 63 days. Fig. 1 represents the microstructure of the annealed alloy with 22 pct Sn. It shows primary a solid-solution crystals in a matrix of the (a + 8)-eutectoid formed at 520 °C. The a crystals contain 8 inclusions which precipitated from a due to the decrease in the solubility of tin in copper with fall in temperature. The decomposition of the 8 phase into a (light) and E (dark) can clearly be seen in some areas of the (a + 8)-eutectoid matrix. However, the decomposition is far from being completed, even after the long-time anneal used. Figs. 2 and 3 depict the microstructures of the annealed 32.6 pct alloy, which was intended to consist entirely of 6 phase. Due to some loss in copper on melting, the composition is slightly higher in tin. Accordingly, the sample after quenching from 400 "C consisted of grains of the 8 phase with the e phase arranged along the grain boundaries and as a Wid-manstatten precipitate within the 6 grains. After an annealing time of 63 days, the eutectoid decomposition, 6 + a + e, is still in its early, initial state. The pearlitic type of eutectoid is nucleated at the c crystals, preferably those surrounding the grain boundaries of the 8 phase. The appearance of the (a + €)-eutectoid in the 35 pct Sn alloy was very similar to that shown in Figs. 2 and 3. Again, the eutectoid decomposition nucleated at the 6 phase and proceeded from there into the 8 areas. As is evident from Fig. 2, the rate of decomposition of the 6 phase at 300°C is extremely sluggish: In the representative area shown only about 5 pct of the 8 phase has undergone the eutectoid trans- formation after annealing for 63 days. On the other hand, Owen and Williams2 have reported that X-ray photographs of powdered samples with between 17.5 and 34 pct Sn did not show 8 lines after annealing for only five to seven days at 300°C. This is in accordance with the fact that the rate of reaction in powdered samples is higher than in massive specimens, as a result of the excess free energy of the powder (due to its greater surface area). The authors wish to express their thanks to C. A. Johnson for preparation of the micrographs.

Jan 1, 1952

By D. S. Tannhauser, I. Bransky

Measurements of the electrical conductivity, the thermal electromotive force, and the deviation from stoichiometry by thermogravimetry were made on ferrous oxide (wüstite) single crystals as well as on poly-crystalline samples in the temperature range of -900" to 1330°C. In the region defined by T 2 1000°C and 1.05 5 O/Fe 5 1.10 the electrical conductivity was shown to be proportional to the sixth root of- the oxygen partial pressure and to be linearly dependent on the deviation from stoichiometry. The absolute Seebeck coefficient of single and polycrystalline wüstite was shown to be independent of temperature in the above region and a p to n transition of the Seebeck coefficient was observed at O/Fe = 1.09 in polycrystalline wüstite. Analysis of the results showed that the predominant defects in wüstite in the above region were doubly ionized cation vacancies. The analysis also ruled out the existence of complexes of the type postulated by Roth, except that below 1000°C there is some evidence of 'association of defects. Of the three oxides of iron (FeO, Fe3O4, Fe2O3) only FeO (wüstite) can exist within a wide range of the ratio O/Fe. This has been shown by several investigations of the phase diagram using for instance chemical analysis of quenched samples'-4 or thermogravimetric measurements. 5,8 Darken and Gurry's1 data for example in the temper- ature range 1100o to 1400°C show that the lowest O/Fe ratio obtainable for FeOl +. is about 1.045 and that the existence range extends to O/Fe = 1.20 at 1400oC. On the basis of detailed analysis of thermogravimetric measurements made by Vallet and Raccah6 the existence of three varieties of wüstite at elevated temperatures was suggested by these authors and by Kleman. It is well-established that wüstite has a NaCl structure with vacant cation sites.3, 8 From a neutron-diffraction study of wüstite samples quenched to room temperature Roth9 concluded that defects in wüstite are mostly complexes composed of two cation vacancies and one interstitial cation in a tetrahedral site. The atomic arrangement in the vicinity of such a defect is similar to that in magnetite, where each occupied tetrahedral site is surrounded by four vacant octahedral positions disposed at the corners of a tetrahedron, so arranged that each vacancy is shared by two tetrahedral cations. Thus there is an average of two vacancies per interstitial. Recent X-ray diffraction measurements made by Smuts10 on quenched wüstite samples confirmed the results of Roth's neutron-diffraction experiments. Roth's model of defects in FeO can be regarded as a solid solution of Fe3O4 in FeO; salmon1' used this defect model to calculate the activity of Fe3O1 in FeO at high temperature and claimed good agreement with the results obtained experimentally by Darken and Gurry.' Each missing cation in wüstite is accompanied by two trivalent cations, thus preserving charge neutrality. The "holes" which differentiate between the Fe 2+ and Fe3' states of the ions in octahedral positions can overcome the attractive field of the cation vacancies, and are then free to move through the crystal as charge carriers. A similar picture holds for COO, NiO, andMnO.l2, 13 Localization of the charge carriers in transition

Jan 1, 1968

By William Hume-Rothery

I need not say how much I appreciate the honor of being asked to lecture to you, and how much I would thank you for your kind invitation. It is encouraging to feel that the abnormal restrictions of the war have been relaxed sufficiently to allow a free exchange of scientists between our two countries, and I hope that some of you will be persuaded to go to England, and to visit us at Oxford, so that I may repay a little of the kindness I have received from you. As this is one of the first lectures since the end of the war, I have thought it well to describe some of the advances in the theory of alloys which were made in the years between the two World Wars. From the point of view of theoretical science, these years have been of outstanding interest in the history of metallurgy. They have been years in which the development of new and more accurate experimental methods has led to the revelation of many new facts. At the same time, the theoretical developments have enabled some of these facts to be viewed as parts of a general scheme, and we may say that some of the foundations of metallurgical science have been laid. This work was naturally stopped by the Second World War, and it can therefore be reviewed as one definite stage in the development of our Science. To illustrate the new advances, I shall deal mainly with the alloys of copper and silver, since these have revealed many of the general principles. taken, and copper had been found to crystallize in the face-centered cubic structure (Fig I). The determination of this structure naturally was of immense importance in the understanding of our subject, because it meant that we were at last in a position to appreciate the underlying structure out of which the crystal of copper was built. The earlier science of metallography had shown that in many alloys of copper the addition of a second metal in not too large proportions resulted in the formation of a homogeneous alloy which was regarded as a solid solution of the one metal in copper. Fig 2, for example, shows the so-called equilibrium diagram of the copper-zinc alloys, and here you will see that there is a solid solution of zinc in copper extending to something of the order 35 to 40 at. pct zinc.

Jan 1, 1947

By Ingersoll Olmsted

Mr. D. H. BRowne's paper upon " The Distribution of Phosphorus in the Ludington Mine" (Trans., xvii., 616) has interested me very much, and perhaps I cannot give a better proof of that, interest than an account of my work and observations in the same direction while chemist of the Hudson River Ore and Iron Company. The ores of this company lie in a chain of low hills running northwest and southeast, about three miles back from the eastern bank of the Hudson river, below Hudson, N. Y. They occur in thick veins, with the characteristic Hudson river slate formation as hangingrock and foot-wall, and dip about 45' east, outcropping in many places near the top of the western slopes.

Jan 1, 1890

By Howland Bancroft

This article is not presented as a treatise on tin mines and mining in Bolivia. It deals primarily with the tin situation, and but fragmentary information is given regarding individual properties, generalizations being necessary in so short an article. Data on general subjects related to tin mining in Bolivia are necessarily abbreviated and very incomplete. It is believed that the references to be found in this article will help those interested to a more thorough understanding of the general conditions extant in Bolivia. Bolivia produces from one-fifth to one-fourth of the world's supply of tin. The United States consumes about one-half of the world's supply and produces practically none. Tin ore is not reduced in the United States. These facts are not generally appreciated by American mining men. Many conflicting data have been published regarding tin in Bolivia. The Transactions of the Institute contain practically no mention of this subject.' I have made a study of mines and mining conditions in the west coast republics of South America and have been particularly impressed by the possibilities of the Bolivian field.= In consequence the thought seems justified that the present meeting would present a fitting occasion to bring the tin situation in Bolivia to the attention of American mining men.

Jan 1, 1914

By H. F. Mills

The Iron King mine is I2 miles east of Prescott Arizona, in low foothills of the Agua Fria mining district. It was operated in 1906 and 1907, using gravity methods of concentration, mostly on oxide ores. In 1923 and 1924 shipments of sulphide ores were made to the Humboldt smelter. It remained inactive and stripped unti1 1936, when it was unwatered and sampled to the 400-ft level, the bottom at that time. In 1937 the Iron King Mining Co. purchased the mine and shipped oxide ores. During 1938 a bulk flotation plant of I40 tons daily capacity was erected. The mill has been enlarged and operations have been continuous since the mill first started. In July 1942, the Shattuck Denn Mining Corporation purchased the physical assets from the Iron King Mining Co., and since that time it has operated as the Iron King Branch of the Shattuck Dcnn Mining Corporation. Economic metals recovered are gold, zinc, silver, lead, a little copper, and fluxing pyrite. The ore occurs as a series of northward-dipping shoots arranged in echelon pattern, the series extending over a length of 3500 ft. Strike lengths of shoots vary from 60 to 600 ft, and widths from 3 ft to as much as 14 ft. The ore occurs in a sheared zone in pre-Cambrian chloritic schist. This schist belt is about 6 miles wide, and the ore zone is about 4 miles from the pre-Cambrian granites to the west. No intrusive rocks have been found in the mine, nor is there evidence of any on surface that might indicate a genetic connection with the ore occurrence (Fig I). The schists strike N23°E and dip 75° to the northwest, which might indicate an overturned thrusting from the granites. In the upper levels, the echelon pattern in which the ore occurs was quite regular. no disturbance of the enclosing schist, or of any faulting that might contribute to the formation of the ore pattern was noted. There is a possibility that the ore zone may be on the axis of an isoclinal fold. Another interesting feature is the more or less typical zoning of minerals along the strike in each of the ore shoots (Fig 2). The north end of each shoot is enclosed by schist, while the south ends usually extend out at full width beyond the economic mining limits in a pyrite-quartz low-grade material. The plane of demarcation between ore and schist is very sharp, with little or no impregnation of sulphide in the schist, especially on the footwall side. The footwall schists are usually firm and strong, and vary from dioritic phases to fine-grained, lighter colored bands, almost silky in texture. The hanging wall for a width of 50 to 80 ft consists of alternating sheetings of chloritic and pyritic schists. The mine is now partly developed to the 920-ft level, with some diamond drilling from the 1150-ft station of No. 6 shaft. Economically there has been little change in nature or grade of ore from the top of the sulphides, about 200 ft below surface, to the bottom levels. There have been a few echelons in depth, just as there are in plan, and while a few shoots have had

Jan 1, 1949

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

The effects of increasing hydrogen content, introducing a notch, and changing the strain rate on properties of titanium and one of its alloys were investigated over a range of testing temperatures from —196° to 200°C. Both high purity and commercial purity A-55 titanium were used as representative a materials, while a commercial Ti-8 pct Mn alloy was used for an a-P alloy. It was found possible to analyze the data, using the ductile-to-brittle transition temperature concept. Increasing hydrogen, the presence of a notch, and increasing the testing speed raised the transition temperature for the a materials. The presence of hydrogen and notches raised the transition temperature of the a-B alloy also. However, increasing the testing speed generally decreased the transition temperature of the a-p alloy. IN previous papers, the authors have shown that hydrogen is most detrimental to the notch-bend impact toughness of a-titanium' and to the tensile ductility of a-B titanium alloys.' These general effects have been confirmed by Kessler and co-workers," and by Kotfila and Erbin." Kessler showed that the slower strain rate in notch-rupture tests was a more sensitive measure of hydrogen embrittle-ment of a-B alloys than the tensile test. In the present paper the authors cover, with tensile and notch-bend tests, the effect of testing speed, notches, and testing temperature on hydrogen em-brittlement. High purity and commercial purity titanium, examples of u materials, and a commercial a-,f3 Ti-8 pct Mn alloy were investigated. The purpose of the investigation was to correlate the factors producing embrittlement. Materials The high purity titanium for this investigation was obtained by arc-melting crystal bar from Foote Mineral Co. into 1 Ib ingots. As-cast hardnesses for these ingots ranged from 60 to 90 Brinell. The arc-melted ingots were forged to % in. diam rods at 1470°F. These rods were swaged to & in. diam at room temperature prior to machining of the specimens for hydrogenation and testing. The commercial A-55 titanium and the Ti-8 pct Mn alloy were obtained from Rem-Cru Titanium Inc., as % in. diam rod. The A-55 titanium was hot swaged to 1/4 in. diam at 1300°F prior to machining of the specimens for hydrogenation and testing. The a-p C-11OM alloy was hydrogenated prior to hot swaging to 1/4 in. roc1 at 1300°F. Hydrogenation prior to fabrication permitted testing of the a-P alloy in the equilibrated and stabilized condition. The equilibration and stabilization treatment used was an air anneal for 1 hr at 1300°F, followed by furnace cooling to 1100°F and then air cooling. Hydrogenation was done in a Sieverts apparatus described previously.' The hydrogenation treatment consisted of heating for 1/4 to 1/2 hr at 820 °C in purified hydrogen, slow cooling to 680"C, holding 1 hr for homogenization, and rapid cooling to room temperature. Intended hydrogen levels for the a-tita-nium materials were 0.05, 0.5, 1.0, 1.5, and 2.0 atomic pct—about 15 to 430 ppm. For the Ti-8 pct Mn alloy, the intended hydrogen levels were 0.05, 0.5, 1.0, 2.5, and 5.0 atomic pct—about 15 to 1100 ppm. The material for the 0.5 atomic pct level of hydrogen was vacuum annealed prior to hydrogenation to increase the accuracy of the addition. Vacuum annealing to remove hydrogen consisted of heating for 6 hr at 820°C, and resulted in a hydrogen content of about 10 to 15 ppm. When hydrogen contents were above 0.5 atomic pct—100 ppm—the hydrogen was added without prior vacuum annealing.

Jan 1, 1957

H. A. BUEHLER, Rolla, Mo. -I consider the lead .and zinc deposits of the Mississippi Valley to be the result of descending waters. There are many features that we have not determined and yet when you see the general field relations, it seems to me that the cause and effect can be well explained by descending circulation. In the Joplin-Miami district, for instance, the ore deposits are connected with openings or with old cavity fillings which have a direct connection downward from the surface to practically 300 ft. In the Miami camp, in the western part of the field, some of the deepest orebodies are directly connected with water, channels; the same condition has been obvious and always present with the shallower ores. I speak of one deposit that I have examined more thoroughly than any other in that district, the Admiralty property, which contains large openings or caves at the deepest levels. It seems to me that waters which would pass upward through 1800 ft. of dolomite would be saturated with lime and magnesia so far as the carbon dioxide of those waters would dissolve them, and therefore, on

Jan 1, 1918

By A. S. Richardson

THE design of mine airways receives, in general, very little engineering treatment. To a large extent this is, of course, due to the fact that information upon which to base calculations is seldom available in definite form. In many mines the extent of the workable deposits may not be known at the time an air course is planned, and the length of service is indeterminable. Volume of air required for ventilation may also increase with extension of the life of a property, and natural obstacles, such as heavy ground, often place limitations upon the size of opening that can be maintained. Perhaps a majority of the shafts used in ventilation of metal mines were originally intended as hoisting shafts, and many of the tunnels and cross-cuts similarly used, were also designed as haulage ways or for other operating purposes. Even when a shaft is sunk solely for ventilation, custom usually dictates a size and shape consistent with the type commonly used for ordinary operations, because experience has demonstrated it can be excavated and maintained. In fact it may not be very far wrong to say most ventilation openings were never made with any consideration as to economic design for such use. When an air course is required to pass air between different parts of mine workings under a fixed pressure, the size of opening required for a given volume of flow, is, of course, determined by the resistance factor of the air course. It is then impossible to proportion the opening with reference to economics of power consumption, and this paper is limited to the design of openings where ventilation pressure or power consumption may be varied for economic advantage.

Jan 2, 1926

By L. W. McKeehan

THE occurrence of twins in large ferrite crystals, made by a new process, was reported in a recent note. This paper describes a typical case of such twinning and suggests, on the basis of the observed facts, why smooth slip-planes are rarely observed in this metal. METHOD OF PREPARATION The material In which the crystals here dealt with were grown was made from 1/8 -in. Armco iron welding rod containing C, 0.04; S, 0.037; P, 0.003; Si, 0.008, and Mn, 0.02 per cent. This rod was cold drawn into wire about 1 mm. dia. A piece of this wire was supported vertically and was locally heated in hydrogen at atmospheric pressure to about 1400° C. by an alternating current (60 cycles per sec.) of about 35 amp., passed through it between a pair of travelling contacts about 8 cm. apart. The rate of travel for the case in hand was 12 cm. per hr. After some 30 cm. of the length of the wire had been heated and cooled in this manner the whole wire was immersed for a few seconds in dilute nitric acid, not restrained by alcohol. Etching was continued until, as nearly as could be judged by eye, the original smooth cylindrical surface of the wire was no longer capable of specular reflection.

Jan 1, 1927

By Thomas Darlington

The obligation of an employer to the State requires certain things of him as matters of good citizenship: for instance, that his workmen shall have a living wage, that child labor shall not be employed, that injuries from accidents shall not make workmen a charge upon the State, and that the laborer's children shall have opportunity for education and to become good and useful citizens. Affairs of this kind are not taken up as philanthropy, for the officials of a corporation or a large manufacturing concern may not feel at liberty to spend the funds of their company as prompted simply by motives of kindliness; but they may spend company money on such matters because it is good business. For years, the poisonous effects of lead, phosphorus, and dust have been emphasized in books on industrial hygiene and their elimination has been urged; but the more important and everyday physiology of the workman himself has been neglected. Part of my object in writing this paper is to show how our knowledge of physiology may be applied to working conditions in everyday life. In the interest of industrial laborers, accident compensation laws have been enacted in 33 States. This has been carried forward rapidly, because it has been shown that it pays both employer and employee. A further step is the recognition of sickness and disablement independent of accidents, not only because of their immediate cost to the worker and to the employer, but because continued efficiency in work and business depends largely upon health. Some measure of the importance of health in industry can be gained by the knowledge that records kept by some companies which now make this the subject of careful inquiry show that the time lost by employees, through illness, is several times as much as that lost as the result of industrial accidents. It is true that accidents frequently result in permanent disability or death, but it is equally true that illness is also a cause of permanent disablement or death. Thus the chief difference is that the loss to the employee through accidents occurring in the course of his employment is now generally recognized as a cost

Jan 1, 1918

By Alexander L. Holley

THE 400-ton testing machine, ordered in June, 1875, by the United States Board appointed to test "iron, steel, and other metals," has lately been completed at the Watertown Arsenal, thoroughly proved and accepted by the Board. The excellence of the machine in every respect is more than satisfactory, and its accuracy is at first sight astonishing, although an investigation of its principles must show that if the weighing apparatus will weigh at all, it must do so with perfect accuracy, because all its movements are absolutely without friction. The proof experiments were numerous, and the effects of recoil after sudden ruptures at maximum loads, were watched with great care, but without much anxiety, because the weighing parts affected are by no means delicate in structure, and their motion is almost infinitely small. Among the tests were the following : A forged link of hard, wrought iron, 5 inches in diameter between the eyes, was slowly strained in tension, and broke short off with a loud report at 722,800 pounds. The diameter before breaking at the point of fracture was 5.04 inches; after breaking, 4.98 inches. In order to see if the weighing parts had been disturbed by the recoil, which was obviously near the greatest recoil the machine will ever suffer, a horse-hair was next tested ; it was 7-1000ths of an inch in diameter; it stretched 30 per cent., and broke at 1 pound. Other horse-hairs vary in tenacity between 1 and 2 pounds. Of course, the accuracy of the machine on such delicate specimens, and indeed on specimens having some hundreds of pounds tenacity, has been checked and proved by other weighing machines. A 5-inch round bar, turned down to 3 5/8 inches diameter along the centre, was pulled apart at 430,200 pounds tension. Then some more horse-hairs were tested ; also copper wires 19 1/2-1000ths of an inch in diameter, which averaged 25 pounds tenacity..

Jan 1, 1879

By C. S. Finney, John Mitchell

The growing popularity in the United States of the vertical-flue even was emphasized when in 1905 the United States Steel Corp. chose the Koppers oven as the type which best suited their requirements. Heinrich Koppers was born on November 23. 1872. at a small farm in Walbeck near Geldern on the lower Rhine. When young Koppers was eight years old, however the family moved away from the farm to the industrial city of Bochum in the Ruhr. Here Koppers attended public school and subsequently served an apprenticeship to a tinsmith before taking a job as a lathe operator with a local steel company. He had ambitions to be much more than a machinist, however, and used his week-ends and evenings to improve his theoretical background by taking courses at a vocational-training school in Bochum. After winning the highest honor the school could bestow (the silver Staats-medaille), Koppers went on to continue his education at the Rheinisch-Westfalische Hüttenschule in Duisberg. One of his teachers there, Fritz Wüst who later became a professor at the Technische Hochschule at Aachen, recognizing Koppers' unusual abilities, predicted for him a great future. In 1894 Heinrich Koppers joined the firm of Dr. C. Otto and Co. in Dahlhausen, and in 1899 while superintendent of the Mathias Stinnes mine he built his first battery of ovens for Hugo Stinnes, the German industrialist. Two years later he started his own organization, and in 1902 he made Essen his headquarters. It was to Essen that a group of engineers from the United States Steel Corp. went in 1906 with an invitation to Koppers to design and supervise the construction of four batteries of ovens at the Joliet works of the Illinois Steel Co. Each battery was to consist of 70 ovens. Arriving in the United States in 1907, Koppers established a branch of his firm in Joliet, and construction began. The first battery was fired on July 27, 1908. Rugged and simple, these ovens incorporated basic design features which were to make the Koppers oven and its future modifications the choice of a very large segment of the by-product coking industry of America. The 280 ovens at Joliet were 35 ft long, 8 ¾ ft in height, and tapered from 21 to 17 in. The total daily capacity of the four batteries was 2240 tons of coke. The ovens were of the new cross-regenerative type; that is, instead of longitudinal regenerators serving an entire battery, as in the older Koppers ovens, cross regenerators for each separate oven were employed. Fuel gas was supplied from the side of the battery through ducts in the brickwork known as gun flues, which reached to the center of the battery under the vertical heating-flues. Removable, ceramic gas-nozzles fitted at the top of each gun flue helped to insure good control over the distribution of the fuel gas, and uniform heating conditions were also promoted by regulating the air supply to, and the suction in, each heating flue. A different refractory w& used for each battery. One was built of American silica brick, one of American quartzite, and two of imported German quartzite. The installation at Joliet proved to be very successful, and in 1911, 490 additional' Koppers ovens were built for the Illinois Steel Co. at the great new steelworks at Gary, Ind. By 1912 the H. Koppers Co. had established its headquarters in Chicago and was rapidly extending its business to include construction for such iron and steel companies as the Woodward Iron Co. at Woodward, Ma. (80 ovens in 1912); the Tennessee Coal, Iron and Rail- road Co. at Fairfield, Ala. (280 ovens in 1912); the Inland Steel Co. at Indiana Harbor, Ind. (86 ovens during 1913 and 1914) ; and the Republic Iron and Steel Co. at Youngstown, Ohio (68 ovens in 1913). In 1914 a group of men in Pittsburgh bought a major shareholding in the H. Koppers Co., and moved the headquarters of the organization from Chicago to their own city. Under its new management the company was highly successful in obtaining a large share of the contracts for by-product installations built during World War I. In 1917 the remaining German interests in the company were

Jan 1, 1961

By L. H. Dushak

DURING the war period of quicksilver activity there were a number of departures from what may be termed the classical quicksilver metallurgy. Attempts were made to beneficiate low-grade ores by gravity concentration and flotation; mechanical furnaces began to replace the Scott furnace and the vertical coarse-ore furnaces, and condensers of sewer tile and redwood tanks were used in place of the older brick and stone condensing chambers. Other developments that have occurred during the current period of quicksilver activity are mainly in the nature of improvement and further refinement of those started during the war period. Each period of quicksilver activity has been accompanied by the proposal of various new processes, including wet methods for the treatment of quicksilver ores and innovations in furnaces, retorts and condenser equipment. As far as the author knows, nothing of economic significance in the way of "new processes" has been developed. There is in fact no real need for any essentially new process for the treatment of quicksilver ores; the direct furnace treatment is simple and inexpensive. Moreover, with rare exceptions, the quicksilver industry has no complex or refractory ore problems corresponding to those which are receiving more and more attention from metallurgists in other branches of the nonferrous field. Under these conditions improvements in quicksilver metallurgy must be looked for through the adaptation of current developments in engineering and metallurgy generally to the particular needs of quicksilver practice rather than through the invention of new processes.

Jan 1, 1930

By Robert W. Hunt

PeRhaps of all the scientific economic questions which have been claiming the attention of capitalists, metallurgists, manufacturers, directors of public utilities, and the general public of America, during the last few years, none have been of more importance than the one relating to the wear and safety of steel rails. The discovery of the Bessemer process made possible modern railway development. In that growth, as has generally happened in all progressive movemeuts, all its departments have not remained equally balanced. Iron rails permitted the construction of roadways for the passage of power-driven vehicles. In time the speed and weight of such carriages proved too much for the wearing-qualities of the rails, and the limit of railway capacity seemed to have been reached. Bessemer made his invention, which was soon perfected and developed, especially as related to steel rails, and thereby increased the limit of capacity, and vastly greater railway progress was made pgssible. The Siemens-Martin open-hearth process followed, and was later supplemented by the Thomas-Q-ilchrist basic improvement. For a time the Bessemer steel rails of commerce were more than equal to all that was asked of them, but this did not long continue, as evidenced by the records in our Tansactions. Revolutionary changes occurred in the industrial world, and in no part of it more than in steel-rail manufacture. Great and powerful commercial combinations were made, whose financial resources made possible the supplanting of the then most efficient blast-furnaces, steel-works, and mills, by others of theretofore unimagined capacity. Old traditions and practices of steel-making were wiped away, and, in too many cases, output was apparently the chief aim, with the result that much dissatisfaction with the wear and safety of rails was felt by railway officials, and the general public was concerned as to its safety when traveling. The climatic conditions of the winter

Jan 1, 1913