Search Documents

By ElRoy Nelson

WATER provides to many mineral industries functions similar to those performed by money in the economic system. Water is a medium of exchange. It is also required in chemical reaction for cooling, for transfer of minerals, and for cleaning. To a great extent, water is also a raw material in almost every industrial operation; it becomes a component of the finished product. In the Rocky Mountain region, water is treated with a great deal of respect. There has not been enough of it when needed. Long ago storage facilities were planned and devised to assure a supply during periods of shortages. This comes from the history of the region in irrigation and mineral processing. Within this region the shovel was always the most lethal weapon used in settling disputes over the use or misuse of water.

Jan 10, 1954

By C. G. Dunn

MANY investigations have been made concerning the nature of plastic deformation and recrystallization of metals either in the form of polycrystalline materials or in the form of single crystals. However, similar work on strip materials composed of large grains as thick as the strip and having a high degree of preferred crystal orientation has not been carried out extensively. Such materials are ideal not only for studying changes in single crystals under conditions where neighboring grains exert their influences but also for obtaining the, complete change in orientation of a grain or group of grains during the course of plastic deformation and subsequent recrystallization. It is well known that first-order twins in the form of Neumann bands may be produced during the plastic deformation of ferrite crystals, particularly silicon ferrite crystals.1-3 Furthermore, it is believe that high-stress regions exist in the vicinity of these bands4a and it has been said that these banded regions would be active in recrystallization processes.5 Evidence to that effect in silicon ferrite had already been presented with photomicrographs showing recrystallization among Neumann bands during the early stages of recrystallization.5,6 Similar evidence has been published for nonferrous metals.5 Merging of fine parallel deformation bands during annealing to form twin bands of ordinary appearance in alpha brass has been offered not only as evidence of an active role being played by mechanical twins but also as evidence that such twins existed prior to recrystallization.5 Proof that such new structures are actually first-order twins, or even twins at all, must be considered inadequate except for those cases where X-ray or optical data have been obtained to confirm the necessary orientation relationship.7,8 A. B. Greninger has obtained excellent iliustrations of annealing twins in alpha irons Since his material was previously deformed by sharp hammering, a process that generally induces Neumann bands, the existence of twins following annealing might suggest that they grew from mechanical twins. In connection with transformation twins in alpha iron, Greninger reported that grains containing. three twin orientations occurred rarely and none occurred with three sets of well-developed bands.9 The work at the Pittsfield Works Laboratory on silicon ferrite in the form of large-grained strip steel deformed a small amount and annealed to partially recrystallize the grains indicates that the deformation and recrystallization processes that lead to annealing twins involve more complex processes than the formation of Neumann bands and the growth of such bands. Some groups of annealing twins are obtained which contain not only three well-developed twin structures, but also contain more than one order of twins. It is also shown, in one case, that an interrelated group of twins did not arise within one single parent grain and, furthermore, orientations of grains in the group

Jan 1, 1944

OFFICERS AND DIRECTORS For the year ending February, 1935 PRESIDENT AND DIRECTOR HOWARD N. EAVENSON PITTSBURGH, PA. PAST PRESIDENTS AND DIRECTORS SCOTT TURNER WASHINGTON, D. C. FREDERICK M. BECKET NEW YORK, N. Y. VICE-PRESIDENT, TREASURER AND DIRECTOR KARL EILERS NEW YORK, N. Y. VICE-PRESIDENTS AND DIRECTORS EUGENE MCAULIFFE OMAHA, NEB. PAUL D. MERICA NEW YORK, N. Y. HENRY KRUMB SALT LAKE CITY, UTAH EDGAR RICKARD NEW YORK, N. Y. LOUIS S. CATES NEW YORK, N. Y.

Jan 1, 1934

Jan 1, 1913

By James W. Halley

' FINE-GRAINED " steels have been standard products for many years. This paper describes an investigation of the effects of some of the more common grain-growth; inhibitors used to produce these steels. The properties, response to heat-treatment, and the deoxidation practice necessary to produce "fine-grained" steels have been the subjects of numerous papers. It has been shown that a substantial quantity of' aluminum is necessary to produce this type of steel, and it has been indicated that titanium and zirconium produce a similar result. For some time there was a lively argument between those who felt that aluminum refined the grain and those who felt that aluminum oxide was the effective agent. This argument subsided with an apparent victory for those promoting aluminum oxide. Most of the work on grain size has divided steels into two broad classifications based upon McQuaid and Ehn's original carburizing test at 1700°F. or some similar test at this temperature. If the steel coarsened at this temperature, it was coarse grained, while if it did not it was fine grained. Quantitative data concerning how much a certain amount of aluminum raised the coarsening temperature and affected the properties, all other factors being constant, are very meager. Similar information regarding titanium and zirconium is practically nonexistent. The published information on aluminum yields some quantitative information. Epstein, Nead and Washburn' gave the first quantitative information on the amount of aluminum necessary to prevent grain growth at 1700°F. They showed that the addition of a pound to a pound and a half of aluminum per ton (0.05 to 0.075 per cent) would assure steel that would not .coarsen during a McQuaid-Ehn test at 1700°F. Herty, McBride and Hough2 reported that a steel containing 0.020 per cent acid-soluble aluminum coarsened between 1742° and 1832°F., while steels containing 0.016 per cent and 0.017 per cent acid-soluble aluminum coarsened between 1652~ and 1742°F. compared with similar aluminum-free steels that started to coarsen at 1580°F. Herty3 also showed a marked improvement in low-temperature notched impact resistance with increasing acid-soluble aluminum up to 0.030 per cent. McQuaid4 compared the coarsening of steels containing 0.011 to 0.204 per cent total aluminum and found a maximum coarsening temperature at 0.098 per cent aluminum. He had no samples between 0.015 and 0.098 per cent aluminum. Houdrement5 found a marked decrease in coarsening temperature with aluminum contents above 0.50 per cent. Kinzel, Crafts and Egan6 found that aluminum and zirconium improved thy low-temperature impact resistance of a low-alloy steel, while titanium was detrimental. Sims7 shows that sulphur increases the coarsening temperature and that the maximum coarsening temperature is between 0.04and 0.06 Per cent added aluminum. The

Jan 1, 1946

By Charles H. Jacoby, Leo E. Read

IN diamond coring salt beds to evaluate deposits, special techniques are applied to standard slim hole drilling to obtain a representative sample of the water soluble sodium chloride. Industrial consumers generally require a run-of-the-mine material of 98.0 pct sodium chloride. Since no commercial beneficiation has yet been devised to upgrade the lower quality salt beds, the only processing is crushing and screening to the size required by the customer. Coring salt sections has recently become important not only in dry mining, but also in the development of brine cavities by hydraulic fracturing and the formation of jugs for storing liquid petroleum products. Drilling Fluid: The fluid used in coring salt beds in New York, Ohio, and Michigan is a thoroughly saturated brine made from 3.0 lb rock salt per gal of make-up water. This mined rock salt, -4 mesh +10 mesh, is dissolved in a lixator, a double-bottomed cone hopper that turns fresh water to fully saturated brine.

Jan 5, 1957

By Edward C. Morse

The metallurgical history of Republic has been completely reviewed in a paper presented at a previous meeting of the Spokane Local Section by Professor Thomson;' therefore, the present paper will be confined to matters directly pertaining to the San Poil mill: When I came to Republic last fall to look over the situation there was a plant in operation successfully treating the tailings from one of the earlier mills in the camp. I refer to the mill of the Rathfon Reduction Co. This mill was operating in accordance with modern cyaniding practice, and I was given to understand that the work was very satisfactory and profitable, else it would not have been continued as long as it was. At that time I obtained much metallurgical information of value from Harry W. Newton, Superintendent of the mill of the North Washington Power & Reduction Co. I took a number of samples from the San Poil mine, with the view of determining if Mr. Newton's experience with the ores from the other mines applied to the San Poil ores. I made a large number of tests under a variety of conditions, and found that it was possible to extract as high as 98 per cent, of the values from San Poil ore by the laboratory-tests when the ore was pulverized to 200-mesh and treated with a solution of a strength of 5 Ib. of KCN to the ton. A fairly strong solution was required because of the proportion of silver in the ore, which makes it, from a metallurgical point of view, practically

Jan 1, 1913

By H. D. Kiddle

IN mining in Malaya has been a courageous ad- venture in private enterprise, attended by all the hazards of prospecting in unexplored areas of tropical jungles-jungles that still cover four-fifths of the country. To assess the contribution of an industry to a country's revenue, it is necessary to consider not only duties levied on the products, but also the revenue from all businesses and individuals directly and indirectly deriving income from the industry. Exact figures are not obtainable, but from 1850 until shortly before the first World War, tin mining in Malaya was a dominant factor in the Federation's development. Even at the turn of the century, tin export duty alone represented 45 pct of total Government revenue, while in the 40-year period up to the end of 1937, tin ore duties collected by the Federated Malay States Government amounted to 383,- 81 0,284 Malayan dollars,* approximately one-fifth of the total revenue for the same period.

Jan 11, 1957

I HAVE previously shown you in the Fifth Book the process of making guns and gun carriages, together with other preparations and methods of moving them. If I now failed to show you more about them, it would be as if I had pointed out only the useless shadow of a thing, for I did not show the kinds and arrangement of their supplies or how the effects for which they are made are achieved. For these reasons I now wish to tell you, in addition to what I have already said, how saltpeter is made and the methods of refining it well; what it is and how without it guns and many effects of violent and artificial fires would have been discovered in vain. After this, I also wish to tell you the methods of compounding the powders for large and small guns, and finally how these are loaded and discharged. I also wish to tell you how mines are made, and fire tubes, [149v] fire pots, squibs, fireballs, rockets, shells, grapeshot, and other similar devices for shooting fire in order to bum ships, supplies, bridges, and ramparts, or, in offense, for firing on batteries. I also wish to teach you to make certain bronze balls for shooting, which carry fire and break in many pieces when they hit. For surely, besides being terrifying to the sight, they would be harmful to armies lined up in battle when they are fighting. Likewise, I wish, to enlighten you as to how artificial fires are made that last long and are difficult to extinguish. Since these are fine and useful things in wars, every captain and soldier should give them consideration and know how to use them when necessary. You will be pleased to have this information if for no other reason than that you can teach it to those who take delight in celebrating holidays with festivities and with fires.

Jan 1, 1942

By R. K. Waring

A KNOWLEDGE of the mutual liquid solubility of zinc and lead is of importance in various phases of zinc metallurgy. The determination of this solubility has been the subject of numerous investigations, but unfortunatel, the results vary widely, particularly at higher tempera-tures, and it has been impossible to decide what data are most reliable. It was decided to investigate the matter and in view of the disagreement in the published results, it was felt necessary to take rather unusual precautions to insure the reliability of the data. For this reason deter-minations were made by four different methods, and the procedures of several of the previous investigators were duplicated. The previously used methods can be divided into two classes: methods involving freezing the entire melt and taking samples of the lead-rich and zinc-rich phases in the solid state, 1,2 and methods in which the. samples are taken while the bath is liquid and at the desired temperature. 3,4 Data obtained by methods involving freezing the entire melt show much lower solubility of lead in zinc than methods in which the liquid is sampled at temperature. The latter method was used by Spring and Romanoff5 and by Hass and Jellinek.6 The results of these two investi-gations are in agreement at temperatures near the melting point but at higher temperatures Hass and Jellinek find a higher mutual solubility.

Jan 1, 1934

By Orville R. Lyons

THE Russellton preparation plant of Republic Steel Corp., located north of Pittsburgh, Pa., prepares 395x0-in. Thick-Freeport coal by means of a 13-ft 6-in. diam Chance cone and 16 No. 7 Deister tables. The plant feed ranges between 370 and 410 tons per hr, of which approximately 31 pct is 1/4xO-in. size, and the plant reject ranges between 14 and 16 pct of the feed.

Jan 6, 1953

By L. L. Swift

AT the present time there are four base metals being used for automo-tive bearing alloys. Of course there are numerous variations in the amounts of alloying elements added to each base metal and nearly all of these alloys have the conventional, if not classical duplex structure; that is, they are composed of a hard constituent embedded in a soft matrix. The well-known theory is that the former will wear well, while the latter will be plastic enough to allow the bearing to be broken in and conform to the contours of the shaft. The requirements of the modern bearing have been most aptly described by W. M. Corse: In order to meet the engineering demands of today a good bearing metal must be able to carry the weight of the shaft and stand up under steady or suddenly applied loads, or even blows in some types of service. A certain amount of plasticity is desired to compensate for minute irregularities in the shaft or bearing surface, and to permit yielding, thereby avoiding dangerous stresses in bearing and shaft and pre-venting overheating and rapid wear of parts. Less plasticity is required in a bearing metal if the surfaces of bearings and journals are machined accurately, aligned, and kept in alignment. It is desirable, of course, that a bearing metal have a low coeffi-cient of friction. Under most operating conditions the friction depends on the unit pressure of the bearing, the speed, the temperature, and the properties of the lubricant. A good bearing metal must have a low rate of wear to reduce the necessity for frequent replacements, and adjustment of the bearings. It must wear more rapidly, however, than the journal or shaft running on it, because replacement of the journal or shaft is more difficult and costly than replacement of the bearing.1 The hardness of the bearing alloy is a property closely related to several of the foregoing. With a duplex microstructure, the measure-ment of hardness with any of the usual commercial devices means little. The Bierbaum method of measuring the hardness of the individual constituents was developed to fill this need.

Jan 1, 1938

By Robert W. Hunt

Having had some twenty years' experience in trying to make good Bessemer steel rails, and now devoting my thoughts and energies to seeing that other people seek the same end, I venture to lay before the Institute some of the conclusions deduced from my practice and observation.

Jan 1, 1889

By A. B. Parsons

NOT every organization on reaching the relatively ripe age of three score and fifteen can say with truth that its purpose and objects remain precisely the same as prescribed by its founding fathers. Of course, constancy of purpose may be something else than unalloyed virtue. It could merely reflect slavish worship of tradition, intellectual stagnation, or sheer inertia. On the other hand, it could establish the fact that the founders were men possessed of broad outlook, of prophetic vision, and of an acute sense of direction. In addition to charting the course with precision, the founders of the A.I.M.E. surely showed a flair for expressing clearly in a few words what others might say obscurely in many words. To quote verbatim from the "call" for the meeting, in 1871, the proposed organization was to have: "two great objectives: "First, the more economical production of the useful minerals and metals. "Second, the greater safety and welfare of those employed in these industries." This text underwent some refining on several subsequent occasions but today the ultimate product, as set forth in the Constitution reads: "to promote the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by all lawful means." The original call was dated "Wilkes-Barre, Pa., April, 1871," and was signed by Eckley B. Coxe, of Jeddo, and by R. P. Rothwell and Martin Coryell, both of Wilkes-Barre, each of the three subscribing himself as "mining engineer." The authors proceeded to explain briefly just how it was proposed to achieve these objectives: "In European countries, where the arts of mining and metallurgy have long been the subject of the most careful study, no means have been found so effectual in attaining the end above proposed, as the free interchange of experience among those actually engaged in these industries; and this object has been accomplished mainly through the medium of `Institutes,' `Associations,' or `Societies,' composed of those engaged in these occupations, and by the periodical publication of `essays' or `papers' communicated to such societies by their members. "It must be evident to all practical men that the interchange of the varied experience

Jan 1, 1947

By W. J. Reagan

In a study of the life of ingot molds, it is essential to eliminate all of the variables. In the commercial manufacture of steel this is almost an impossibility. In this study many of the variables have been eliminated, and because of the unusually consistent furnace practice, with small variations in the type of steel manufactured, and a similar type of mold design for all ingot sizes, it is possible to determine with some degree of accuracy the cause of variations in ingot-mold life. All of the ingot molds in this study were used in the production of basic open-hearth killed steel with chemical analyses within the following range: C, 0.50-0.85 per cent; Mn, 0.60-0.80; Si, 0.20-0.30; S, 0.04 max.; P, 0.04 max. All ingot molds were of the closed-bottom type and used for bottom casting only. None of the molds in the study failed from cutting of the sides due to top casting; in fact, on only rare occasions are any molds used for top casting. The general type of this mold is shown in Fig. 1. All sizes have rather a heavy band of metal, about 6 in. wide, at the top to give mechanical strength at this point, and all have cast lugs. Cross sections of the various sizes from top and bottom sections are shown in Fig. 2. Ratios of wall thickness to ingot weight, ratio of ingot diameter to ingot length, and other figures of interest are shown in Table 1. In the majority of cases, the cause of failure in this type of mold is due to heavy fire cracking on the "flats" at a point from 3 to 6 in. from the bottom radius of the mold. Fig. 3 pictures this type of failure. The start of failure at these points usually begins with a very small section of the interior surface becoming involved. As a rule, a section of 1 or 2 sq. in. is the first noticeable indication that mold failure is taking place. Gradually the small section increases until a sizable cavity develops, causing a protuberance on the bottom of the ingot, which eventually becomes too large to be stripped. The mold is then removed from service. At the time of failure, this cavity often reaches a size of about 5 sq. in. and about 1/2in. deep. Sometimes cavities are found on only two or three sides and at other times all twelve sides appear to be invoIved.

Jan 1, 1937

By George Haworth

ELECTRICAL illumination of shafts, stations, and haulageways has been successfully practiced for many years, but its use in drifts and stopes where mining operations are carried on has- been limited. The large underground drifts of the Tri-State field present a lighting problem that is not satisfactorily solved by the use of the carbide lamp. It has, for some time, been the policy of the Anna Beaver mine to provide ample lighting throughout the underground haulage drifts and working faces. This has, in the

Jan 6, 1928

Jan 1, 1934

By R. F. Hehemann, Darrell W. Smith

The kinetics of alloying- in W-5 rot pct Re powder compacts were investigated at temperature about the upper limit for the formation of the x phase, such that a single intermediate phase was involved in the process. The rates and directions of motion of the a-o and o-b interface were assessed as functions of tinze at the sintering teri7peraticve by quantitative izetallog-ralhic techtziques. The iiotion 01 these interjuces could be specified approxitnate1.y by u Parabolic )-ate law and deviations from this ,rate law were attribuled to a complex interaction between surface dif'fusion and volume diffusion during the initial stages of sintering. WHEN binary or more complex alloys are produced by sintering compacted blends of elemental powders, a complication is encountered which does not arise in the sintering of pure metals. In addition to concern for grain size and densification, the rate of inter diffusion of the component elements must be considered. The general problem of alloying during sintering has been treated by numerous investigators.'-7 These investigations have been concerned only with systems that form continuous series of solid solutions and a concentric-sphere diffusion model4 provides a useful description of homogenization in these stems.' Some controversy remains, however, over the contribution of surface and grain boundary diffusion to the homogenization process. Heckel% ePorts that homogenization can be described by volume diffusion at all temperatures, whereas other invetiators'' recognize the importance of surface and grain boundary diffusion, particularly at lower temperatures. Analysis of the homogenization process in partially miscible systems is complicated by the motion of the interfaces separating the individual phases. A simple analytical solution does not exist for such finite systems with spherical symmetry. It was the purpose of this work to examine the kinetics of the formation and dissolution of an intermediate phase in a binary system through an assessment of the motion of the interfaces separating this phase from the terminal solid solutions. PROCEDURE The W-Re system is an example of a partially miscible binary system and was selected for study because of its current importance in refractory-metal technology. The equilibrium phase diagram, Fig. 1, shows that the o phase will be formed by interdiffu-sion between tungsten and rhenium. At temperatures between approximately 2125" and 282O°C, the o phase will appear as the only intermediate phase in the diffusion system. In this work, a mixture of elemental powders containing 5 pct Re was employed. In such a mixture, the rhenium particles will be distributed randomly in a tungsten matrix. During sintering, a o-phase layer will form at the W-Re interface. The development and subsequent disappearance of the o phase are controlled by the relative rates and directions of motion of the 0-0 and a-p interfaces. The motion of these interfaces can be inferred from quantitative metallographic measurements of the average radii of the o shells surrounding rhenium particles. Elemental tungsten and rhenium powders of commercial purity were employed in these investigations. The rhenium powder was spheroidized from +200 mesh agglomerates by plasma-arc spraying and was then classified to yield a powder composed of essentially

Jan 1, 1967

By W. J. Rooney, James Fisher, W. O. Hotchkiss

During the summer of 1927, the Department of Terrestrial Magnetism of the Carnegie Institution of Washington joined with the Michigan College of Mining and Technology in conducting a series of earth-resistivity measurements in the Michigan copper country. The geological structure in this section is quite varied and fairly well known. The purpose of the investigation was to discover the correlation between the variations in electrical resistivity of large masses of soil and rock in place and the geological structure below the surface. The work done may be roughly divided into two parts: (1) Measurement and study of the variations in resistivity with depth, or with volume, to establish such general relations as exist between the two; and (2) the determination of the specific resistivity of various formations in order to make available more fundamental data which may aid in the interpretation of the results of the former type of measurement. A report by Mr. Rooney, which gives in detail the measurements made and the results obtained, forms the basis for this article. Measurement and Study of Variations in Resistivity The possibility of applying data from measurements of the physical properties of earth material to the study of the geological structure has long been recognized, and a number of methods for determining the position and character of concealed rock strata by means of seismic, gravitation, magnetic and electrical measurements made on the surface are being used with varying degrees of success. One physical property which varies widely for different materials, and hence affords an opportunity for distinguishing between them, is their electrical resistance. Locations • were selected where the geological structures were well known and where the depths to the water level and bed rock had been determined by drilling. The problem was to determine the value of measurements of resistivity and its variations as indications of the geological structure below the surface.

Jan 1, 1929

THE metal iron has physical arid chemical properties which are some- what different from those of steels, but a knowledge of the pure metal is a useful starting point in studying the behavior of steels. Solid iron exists in two different crystalline forms, called alpha (a) and gamma (?) iron the former being the ordinary form at room temperature. When heated above the "A2 point," 769 C (1416 F), the metal becomes nonmagnetic, and at the "A3 point," 911 C (1672 F), it undergoes a change in crystalline form to become gamma iron. 111 the range 769 to 911 C, it is sometimes called beta (ß) iron to distinguish it from the magnetic alpha, but the two are identical in crystal structure. When gamma iron is further heated to 1392 C (2538 F), it changes into delta (d) iron, which is identical with beta or nonmagnetic alpha iron. Pure iron melts (in an inert atmosphere) at 1536 C (2797 F); the melting point is generally lowered by alloys or impurities. PHYSICAL AND THERMAL PROPERTIES OF IRON Many of the properties of iron undergo abrupt changes at the transition temperatures.1 For example, in heating through the A3 point, a sudden shrinkage in volume occurs. Similarly, melting is attended by sharp physical changes such as an increase in volume. Table 16-1 contains a summary of the measured physical properties of pure iron at several temperatures. Usually the properties change smoothly with the range of stability of a given form, but this is not always true. For ex- ample, the specific heat reaches a sharp maximum at the A2 point al- though no transformation occurs. (See Fig. 14-1.) Solvent Powers of Liquid Iron. Liquid iron is capable of dissolving most of the other metals and many nonmetallic elements as well. Of the metals that are liquid at the melting point of iron, only lead, silver, and bismuth refuse to dissolve to an appreciable extent. Table 16-2 contains a list of the common elements classified with respect to their solubility in liquid iron. Those which are very soluble or practically insoluble require no further discussion, but several of the nonmetals that are gases and exhibit limited solubility are of considerable importance to us and merit more detailed consideration.

Jan 1, 1964