Search Documents

ALTHOUGH the open-hearth charge contributes CO, C02, H2, and water vapor to the combustion gases and absorbs oxygen from them, in the main the thermal effects in the melting charge and molten bath can be considered independently of those in fuel combustion; the latter then is regarded simply as the source of the net heat required to finish a heat of steel. First of all, it should be remembered that a large percentage of the heat supplied to the bath is furnished by oxidation of the various elements in the charge itself. If this charge consisted of 80 to 100 per cent of hot metal and the oxidation were accomplished by blowing in air or oxygen, as in the bessemer converter, the net heat absorption would be negative; that is, the bath would contribute part of the heat required to keep the melting chamber hot, in addition to that contained in the finished steel and slag. - In actual open-hearth practices, probably the nearest approach to this is in the duplex furnace, charged with bessemer-blown metal and some hot metal, where very little heat is required to complete the refining and nearly all the heat energy from fuel combustion is used to keep the roof and walls of the melting chamber up to around 2900 to 3000 F (1600 to 1650 C), so that the bath will not cool off during the refining. The other extreme is with all-cold charges containing around 80 per cent steel scrap and 20 per cent cast iron or cold pig iron, in which case a very large proportion of the heat in the bath at tap is supplied from the fuel combustion. THERMAL EFFECTS IN MELTING In a typical heat, the fuel furnishes about four million British thermal units per ton of steel produced. The heat required for the metallurgical processes is not easily defined in useful manner but it ranges downward from about one million Btu, depending not only on the charge but on the manner of calculation. In any event, this requirement appears small in comparison with the

Jan 1, 1951

By Nathan C. Rockwood

THE title of this paper, I understand, was suggested by professional mining engineers as an opportunity for someone to pose problems rather than to offer solutions for them, but the paper will merely attempt to pose some of the production problems of the mineral aggregates industry in such manner as to create professional interest in their solution by the mining engineer, geologist, geochemist and the metallurgical engineer versed in mineral-dressing technique. DEFINITION OF MINERAL AGGREGATES "Mineral aggregates" may be defined as fragments of any rock or mineral used to supply bulk or volume or substance for a given purpose. For example, mineral aggregates are used in portland-cement concrete to provide bulk with the expenditure of the least feasible amount of cement binder. Mineral aggregates are used without portland cement or bituminous binder in highway and railway roadbeds to provide substance, to carry loads. Mineral aggregates are used in filters for water and sewage, to provide substance for the liquid to trickle through. These are only a few typical uses of mineral aggregates. For all these uses, strength, toughness, resistance to abrasion, and durability are usually prime requisites; so, while theoretically mineral aggregates may be of any mineral composition, what really is desired is a mineral composition as nearly inert under the conditions of use as anything of earthly origin can be. EXPLORATION AND POSSIBILITIES OF DEVELOPMENT The distribution of deposits of mineral aggregate is universal, since almost any part of the earth's crust can be used; even the top soil is sometimes used in stabilized surfacing for highways or airport runways. Nevertheless there is ample opportunity for exercise of the talents of the mining engineer and the geologist in finding the particular deposit that will be most economical to develop, keeping in mind such considerations as: (1) quality and mineralogical characteristics of the material; (2) size and permanency of the market; (3) final cost of opening and development of the deposit; (4) selection of location of plant; (5) methods and costs of distribution of the product in comparison with both present and possible future competition; (6) selection of the proper type of operating equipment; (7) estimation of probable waste products and their disposal. These are typical but there are other considerations also. Because profit margins are far smaller than in any comparable mining operation, it is all the more logical to assume that a higher degree of expert knowledge is desirable to make a success of a mineral-aggregates business. The industry has much engineering talent in its operating branch, but it lacks, to a considerable

Jan 1, 1943

By Fritz Wald, Richard W. Stormont

lHE general constitution of a number of metal-lead telluride and metal-tin telluride systems has recently been studied in an effort designed to furnish background information for the study of degradation mechanisms on junctions between thermoelectric power generation materials and metals.1"4 This paper reports further results of that effort. It was found that cobalt-lead telluride constitutes a stable pseudobinary section through the ternary Co-Pb-Te system. Materials used in the study were lead and tellurium of semiconductor-grade purity (American Smelting and Refining Corp., 99.999+ pet). Cobalt (Johnson Matthey & Co., 99.999 pet purity) was used in the form of slices cut from rods of 5 mm diam. Twenty- gram charges of the alloys were melted in evacuated quartz ampoules. Thermal analysis, as described previously,2'3 and metallographic and X-ray diffraction methods (Debye-Scherrer photographs) were used as investigative tools. Substantial difficulties were encountered in polishing, as reported previously for the lead telluride-iron system.3 A number of different etches were used, including dilute aqua regia, Murakami solution, an etch containing copper nitrate,3 and HC1-HNO3-acetic acid-water mixtures. None of these etches gave consistent results over the complete range of cobalt concentrations. On the alloys containing bulk cobalt in the form of primary

Jan 1, 1969

By John J. Gilman

F many years it has been suspected that a correlation existed between pits produced by etching and the density of dislocations in crystals. In 1953, the interest in this correlation was greatly stimulated when Vogel et al' demonstrated a 1:l correlation between etch pits and dislocations in low angle grain boundaries of germanium. About two years ago, the author began attempts to produce etch pits at dislocation sites in zinc mono-crystals. These attempts met with success a year or so ago,' and since that time a survey has been made of the etch pit patterns that are associated with various modes of deformation in zinc monocrystals. Unfortunately, the etching technique that will be described is too delicate for use as an accurate quantitative tool. Nevertheless, it has been of considerable assistance in clarifying the structure of plastically deformed crystals. Technique Many attempts were made to produce etch pits in high purity zinc crystals. It was found that several techniques would produce surface grooves at grain boundaries that had misorientation angles greater than about l°, but no technique was successful for boundaries with smaller angles. Among the things that were tried were: electrolytic CrO, (both etching and polishing concentrations), HNO, in various water and alcohol solutions, dilute HC1, many 0-0,-Na,SO, solutions, Cr0,-HC1 solutions, picral, electrolytic Na,S,O,, and electrolytic NaOH and KOH. A few attempts to use cathodic sputtering and thermal etching were also made.

Jan 1, 1957

Iron and steel lire subjects that will receive the attention clue them at the meeting in. St. Louis. Within the past 2 years the smelting of iron ore on a large scale has been started in the St. Louis area, and the blast furnaces are in full operation. Ore is being received. from the Lake Superior region, in large barges .brought clown the Mississippi River. Firebrick, for the lining of the furnaces, is made in the. St. Louis district to a greater extent than elsewhere in the country. At this meeting, there will probably be a discussion of the possibilities of the increase of manganese production in this country, and of improved methods of using it in steel manufacture.

Jan 10, 1917

The School of Mineral Industries is dedicated to education in mineral conservation and research by which the means may be found to make conservation effective. This includes diligent search for mineral truths and the energetic discovery, complete recovery, and maximum utilization of irreplaceable mineral resources. Standards of living depend upon two factors: human resources-intelligence, imagination, initiative, know-how, work; and natural resources-plants, animals, and minerals, including water, air, soil, heat and light from the sun, and all other such resources that are useful to man. Human relationships have not kept pace with scientific achievement; as a result man, in desperation, wittingly, premeditatively sacrifices freedom for security. Many natural resources, through overproduction, mismanagement, and greed, have definitely moved over into the exhausted or exhaustible category. The United States cannot maintain present standards of living on an agricultural economy alone, and serious harm can ensue if there are marked disproportions in numbers and relationships between city and rural populations. The most materialistic New Yorker must see virtue in bucolic loveliness. The United States is rated wasteful and inconsistent most of the time. It does not make sense to dole out through the keyhole what a wage earner can bring through the open door; to raise wages to lower the cost

Jan 1, 1950

SEC. 1. The membership of the Institute shall comprise seven classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members; 7. Junior Foreign Affiliates. All shall be equally entitled to the privileges of membership, excepting that no member of any class whose residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain Members.

Jan 1, 1946

By George H. Found

DURING recent years considerable interest has been focused on the energy-absorption characteristics of metal when it is cyclically stressed in vibration. The most familiar manifestation of this phenomenon, which is called the "damping capacity" or "internal friction" of a material, is involved in the dissipation of mechanical energy of vibration, which otherwise would build up to stress levels where the problems of noise and fatigue are involved. In addition to its engineering importance in structures, the damping behavior of metals, particularly at low stress amplitudes, has also been used as a unique metallurgical research tool with which to provide sensitive means for indicating certain structural changes within metals. Important contributions toward understanding the energy-dissipating mechanisms that are responsible for internal friction in metals have been made in the last few years. The information is not yet sufficiently extensive, however, to provide a useful metallurgical concept describing exactly how the structure affects the internal friction, or to encourage more general use of this technique among metallurgists. Three fundamental mechanisms have been proposed, as a result of recent experimental investigations, to account for the internal friction in nonferrous metals in low-stress amplitude tests. These include damping due to internal thermal currents that are created and flow in metal because of differential vibratory stress effects,1 damping due to localized inelastic stress relaxation at inhomogeneities within the metal,2,3 and damping related to plastic flow of a localized type for which an explanation has been sought in terms of the dislocation theory.4 How each of these mechanisms functions as a result of structural changes in the metal is, in general, not well understood because of insufficient experimental data for which the controlling variables have been segregated and because of uncertainties in regard to the nature of the structural changes themselves. In several investigations the effects of cold-working on the internal friction of polycrystalline brass and aluminum have been described. As reported by Köster and Rosenthal,5 and by Förster and Breitfield,6 there is an initial large increase in the damping when the metal is worked. The initial high value is not stable, but declines rapidly, at first, in a hyperbolic manner. About 100 hr, after straining, a stable value is reached of magnitude proportional to the amount of strain.7 In Fig. I is shown the relationship found by Zener and his collaborators between the internal friction due to cold-working of alpha brass and the amount of cold-working.8 Several investigators have made internal-friction measurements on worked poly-

Jan 1, 1945

By William M. Baldwin, T. S. Howald, A. W. Ross

EXPLORATORY WORK THE related subjects of preferred orientation, directionality in physical properties, and earing tendencies of wrought metal [ ] strip have attracted the attention of metallurgists to such an extent that in the past 20 years hundreds of researches have been published on this one general problem. The anisotropy of tensile strength and elongation have been exhaustively studied in their relationship to the occurrence of ears in cups drawn from strips-20.29 and, to a lesser extent, yield strength7,11,17 and stress-strain curves" have been investigated. Despite the tremendous fund of knowledge thus accrued, no simple quantitative correlation of directionality and earing tendencies has yet been found. In a sense, this is not surprising. The formation of ears in a drawn cup clearly is a special phase of the general study of metal flow; in particular (as will be brought out in the course of this paper), ears are due to anistropy in the rates of deformation of the metal in the radial, circumferential, and "thickness" directions of the original blank. It would be difficult to effect a correlation between earing tendency and a property that may be completely independent of the flow of metal, or at best related to metal flow in an exceedingly complex fashion. Yet, it is this correlation that has been attempted; tensile strength and elongation are attributes of metal rupture, a phenomenon that has quite admirably been shown to be distinct from the phenomenon of metal flow,21 while yield strength and stress-strain

Jan 1, 1945

By W. F. Carew, F. A. Crossley

The stress for rupture in 500 hr at 1000° F has been reported to be about 13,000 psi higher for Widmanstitten than for equiaxed microstructures for the Ti-7A1-3Mo alloy.1,2 Also, limited data indicated Widmanstatten and equiaxed micro-structures to have approximately the same creep resistance at 1000°F.' Recently, data have been obtained which show Widmanstatten structures to be significantly more creep resistant than equiaxed structures at 1000°F, see Fig. 1. These data represent several ingots and several heat treatments of the solution treat and age type. The thermal history and tensile properties corresponding to the creep data are given in Table I. The creep data were taken from creep-rupture tests. The associ- ated rupture data are given in Table 11. It may be noted that total creep deformations are considerably greater for equiaxed structures. Previous evaluations of stability indicated that all of the structures tested are stable with respect to exposure to stress at elevated temperature.1,2 For a minimum creep rate of 10-4 in. per in. per hr the difference in stress levels is indicated to be about 17,000 psi. Holden,et found an irreversible contraction upon heating three a-ß titanium alloys in the equiaxed condition above their ß-transus temperatures. The alloys were: Ti-6Al-4V, Ti-155 A (5Al-1.3Cr-1.5Fe-1.2Mo), and C-130 AM (44-4Mn). The net contractions in length between the original equiaxed and the final Widmanstatten structures measured at room temperature were: 0.4, 0.4, and 0.7 pct, respectively. The greater creep and rupture resistance of the WidmanstStten structure of the Ti-7Al-3Mo alloy may be associated with the phenomenon

Jan 1, 1959

By W. Vickers

SALKOVITZ1 has given a number of useful angles between planes for use with the Laue method in determining the orientation of bismuth single crystals. Bismuth is usually considered as having a face-centered-rhombohedra1 structure with its axial angle 87°34', Fig. 1. A similar figure given by Sal-kovitz appears to be in error in that the angle there marked as 87°34' should be 92°26. The primitive cell is a single rhombohedron of axial angle 570 14. The structure is almost face-centered-cubic and hence high accuracy in measurements is essential if there is to be no confusion in indexing poles or zone axes. It is easier to get this accuracy if zone axes are plotted on the stereogram because they will lie near the basic circle where the net has a more open scale. The zone axes can be read from the film, using a Greninger chart, and can be plotted more accurately than poles. Also, the angles between points near the basic circle can be read more accurately than those between poles near the center. In order to use the zone axes the angles between directions have been calculated from a formula given by Niggli,2 and are given in Table I. Miller indices

Jan 1, 1958

By E. W. Hough, G. L. Stegemeier

Empirical equations for surface tension of propane and normal butane as functions of reduced temperature are obtained from experimental data. Another correlation relating surface tension to enthalpy of vaporization is given for these two compounds. In addition, new paracbor numbers are calculated for the normal paraffin hydrocarbons. These numbers are utilized for the calculation of interfacial tension of two-component systems as functions of pressure and temperature, using a modified form of Weinaug-Katz equation. The experimental data for two binary systems are approximated by the correlation. From these results it is found that the interfacial tension in the high-pressure region remains extremely low at large pressure decrements below the critical pressure. Thus, it appears that condensate systems may have flow characteristics almost like single-phase conditions even though the pressure is within the two-phase region. Experimental data have shown that interfacial tension divided by density difference approaches zero as the critical pressure is approached. A calculation of wetting-phase saturations indicates that the saturation gradient at the two-phase contact becomes increasingly abrupt as the critical pressure is approached. DISCUSSION Prediction of the surface and interfacial tension of the light hydrocarbons and of two-component hydrocarbon mixtures at various temperatures and pressures may be made if other physical properties are known. Extensive experimental work on single-component and binary systemsl is the basis for the correlations outlined in this paper. Interfacial tension is defined as the specific surface-free energy between two phases of unlike fractional composition, while surface tension is defined as the specific surface-free energy between two phase:; of the same fractional composition. The usual definitions relating interfacial tension to a liquid-liquid interface and surface tension to a gas-liquid interface are not clearly defined when the critical region is included, and there is no sharp distinction between a gas and a liquid phase. Interfacial tension is probably the most important single force that makes one-half to one-third of the total oil actually in place in a reservoir rock unrecoverable by conventional gas-drive or waterflood methods. A rough estimate of this figure for the United States is 100 billion bbl. Interfacial tension presently is used by petroleum engineers in the estimation of saturation gradients at the gas-oil contact and at the oil-water contact. The data in this paper should prove useful for estimates of reserves involving gas-oil contacts. Relative permeability undoubtedly is influenced by interfacial tension, for sufficiently small values. These data should be useful in determining how small the values are In addition, these data should eventually add to our fundamental knowledge of surfaces. At the critical point, all surface excesses approach zero and the thickness becomes very large. SINGLE-COMPONENT SYSTEMS It has been observed1 that the following relationships are good approximations to the physical properties of propane and n-butane.

By Robert W. Hunt

The memorable features of American history have been making fast during the last century, and notably so since 1860; and they are by no means confined to political or to any one branch of scientific development. Of all the industrial arts, none show a greater change or 'a mightier progress than the Bessemer manufacture. And this year, while we are celebrating the first centennial of our national life, we can also celebrate the first decennial of American Bessemer practice. While not forgetting or undervaluing what has been done in other countries, I have thought that a brief history of the introduction and development of the Pneumatic or Bessemer process in America would be of interest. In 1863 the Kelly Pneumatic Process Company was formed and an arrangement entered into with William Kelly, who had taken out letters-patent of the United States, Nos. 16,444; 17,628, reissued as 505; 18,910, dated January loth, 1857; June 23d, 1857; November 36, 1857; and December 22d, 1867, respectively. This association mas composed of the Cambria Iron Company, E. B. Ward, Park Brothers & Co., Lyon, Shorb & Co., Z. S. Durfee, and, later, Chouteau, Harrison & Valle joined the combination. Not satisfied with possessing the control of the Kelly patent, they sent Mr. 2. S. Durfee to England, to secure for this country Mushet's patent on recarburization, No. 17,389, dated May 26th, 1857, the same having been taken out in England on September 22d, 1856. In this Mr. Durfee was successful. Previous to the application of William Kelly for a patent, Henry Bessemer, of England, had taken out patents dated February 12th, 1856, and August 25th, 1856, in this country. Kelly claimed priority in the discovery of the principles of the process, and the Patent-office allowed his claim by granting him his patents. In the autumn of 1862 Mr. Alexander L. Holley, while in England, was impressed with the importance of Mr. Bessemer's invention, and so fully foresaw its future, that, upon his return to the United States, he induced Messrs. John A. Griswold and John F. Winslow, of Troy, New York, to join him in endeavoring to possess Bessemer's American patents. Mr. Holley returned to England in

By T. R. Scott

The acid pressure leaching of zinc-lead flotation concentrates from the McArthur River deposit, Northern Territory, Australia, has been studied in a three-stage, continuous, co-current system, using titanium reactors of 6 gal capacity. The starting pulp contained 2.7 lb solids per gal of synthetic spent electrolyte and the final liquors contained 120-125 gpl Zn. Parameters investigated included temperature (95-120°C), oxygen pressure (30-100 psi), acid addition (80-130% of theoretical), and leaching time (35-65 min per stage). Technical factors studied included mixing and pumping of feed, agitation, settling and washing and control mechanisms. The chemistry of liquor impurities, of scale formation in autoclaves and of lead jarosites in residues was studied in some detail. Results indicated that 90-93% zinc recovery could be obtained with a "low- acid" process, using 113°C and 70 psig with oxygen as the favored operating conditions. Residues contained 16-18% elemental sulphur and 15% lead, together with unreacted pyrite and gangue minerals. Pelletizing of residues was impracticable, and alternative suggestions for the recovery of lead, sulphur and silver are discussed. Preliminary estimates for plant and operating costs are given and enable some comparison to be made with conventional procedures.

Jan 1, 1973

By Charles N. Becker

The practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1938

By Irving Fatt, Robert J. S. Brown

INTRODUCTION The wettability of reservoir rocks is recognized as one of the major factors that determines their multiphase flow properties. Multiphase flow properties in turn govern reservoir performance. For this reason, the reservoir engineer is vitally interested in the wettability of reservoir rock. The production research scientist is interested in wettability because the solution of the problem of improving waterflood recovery by use of surface-active additives may hinge on a detailed understanding of the wettability of reservoir rock. Early workers believed that all reservoir rocks were preferentially water wet. Continued study soon uncovered certain rocks which had flow properties that indicated that they were preferentially oil wet. Recent studies show that there is a spectrum of wettability. Some reservoir rocks have multiphase flow properties which indicate that they have an intermediate wettability. The differences in recovery observed among different reservoirs may, in part be the result of small differences in wettability. Differences in wettability amcng reservoir rocks may be the result of differences in the fraction of the total surface area that is preferentially oil wet and preferentially water wet. Nuclear magnetic relaxation measurements may provide a method for determining the fraction of preferentially oil wet and preferentially water wet area in porous media. Measurements to be reported here were made on water-saturated unconsolidated sand packs which were mixtures of preferentially oil wet and preferentially water wet sands. The resulting data show definitely that the fraction of each wettability in these sand packs can be determined by this nondestructive method of measurement. THEORY OF NUCLEAR MAGNETIC RELAXATION The details of the theory of nuclear magnetic relaxation have been presented previously1. In this paper, only a very brief review of the theory will be given to show its application to the measurement of fractional wettability. Nuclear magnetic relaxation is a process of adjustment undergone by certain atomic nuclei when their magnetic environment is changed. They adjust, or relax, to be in equilibrium with a new magnetic field. The reason that some atomic nuclei are affected by a magnetic field is that they themselves behave in some respects like tiny magnets. In particular the proton, the nucleus of the hydrogen atom, behaves as a magnet. The proton spins, somewhat as the earth spins on its axis. The spinning charge produces a magnetic field just as current traveling in a loop of wire produces a magnetic field. No net charge is required, however; for instance, the neutron has spin and magnetic moment. When the spinning proton is subjected to an externally applied magnetic field, its axis tends to line up with the magnetic field, somewhat as a compass needle tends to line up, but the spinning proton cannot do this as easily as the needle can. The proton also has mass, and its spinning mass makes the proton behave somewhat like a gyroscope. As is well known, a force which tends to change the axial direction of a gyroscope merely causes the gyroscope to precess: lhat is, the axis begins to trace out a conical surface. The gyroscope cannot actually assume the position suggested

Jan 1, 1957

NEW MEMBERS The following list comprises the names of those persons who became members during the period Aug. 10. 1918, to Sept. 10, 1918. BATCHELOR,. HARRY D., Laboratory Director, National Carbon Co., Inc., Cleveland, Ohio. BROWNING, C. P., Gen'I Supt., Britannia Min. & Smelt. Co., Ltd., Britannia Beach, B. C., Canada. COMSTOCK, GEORGE F., Met., Chg. of Physical Test Laboratory, Titanium Alloy Mfg. Co., Niagara Falls, N. Y. CONCKLIN, BERT M Chief Engr., Arthur lron Mill. Co., Hibbing, Minn. COWAN, W. A., Asst. Chief Chem., National Lead Co., 129 York St., Brooklyn, N. Y. DAVIDSON, PHILIP Met., Scovill Mfg. Co., Waterbury, Conn. DAVIS, Louis L., Mgr. & Treas., Commonwealth Min. Co., 911 Foster Bldg., Denver, Colo. DAY, P. W Chem. Engr., Western Cartridge Co., 207 E. 12th St., Alton, Ill. DECKER, HAROLD DEBIT, Co. A, 27th Engineers, A. P. 0. 714, A. E. F., Care Postmaster, N. Y.

Jan 10, 1918

By R. P. Rothwell

THE first difficulty mentioned is that in some instances two or more beds of coal separated by sandstone or slate rocks of considerable thickness in one part of a basin, are found running together in another part. Of course, we may happen to strike first the part of the basin where there is but a single seam, and in this case the bed would appear to divide into two or more branches within a short distance. Such cases are not rare in the anthracite coal-fields. I would suggest as an explanation of this phenomenon the gradual sinking of the peat-marsh-the embryo coal-bed-on one side, and the moving forward of the marsh, so that on one part of the bed the formation of peat would still be progressing, while another part, being under water, would be covered with mud and sand. Thus we have different portions of the same bed of different ages. Now if the sinking of the marsh be stopped for a time, the bed will become thicker in the portions left exposed, and if the sinking now changes in direction, so that the part that had previously gone down com¬mences to rise, we should have the phenomenon of a bed, continuous throughout, with one portion overlying another, and separated from it by rock strata. These are exactly the conditions observed in splitting beds. While one side of the lake is sinking, and the peat-marsh moving on in that direction, the other side may be rising,

Jan 1, 1873

By D. R. Shreve, L. W. Welch

An analysis for predicting the behavior of reservoirs exploited by a combined gas drive and gravity draintrge mechanism is presented. The method allows the prediction of gas-oil ratio, oil production rate, and cumlulative oil recovery for high relief pools in which pressure is maintained either by gas injection in the crest of the structure or by a combined gas and water injection program. The reservoir is represented by a model of communicating vertical prisms, with production or injection at the upper or lower boundaries of each prism. The theory of macroscopic gravitational segregation of two fluids within a reservoir is discussed in detail for all ranges of saturation. A description of an application of the analysis to a typical field problem is also presented. INTRODUCTION The importance of gravity drainage as a producing mechanism has become more evident during recent years. However, many of the reservoir engineering methods which have been used in the past for predicting the behavior of reservoirs producing by this mechanism have required such drastic, simplifying assumptions that the calculated performance in some cases does not resemble the actual pool behavior. The mechanism of fluid displacement in porous media has been described by Buckley and Leverett,1 and a simplified "one zone" method based on this development has been used by engineers to evaluate the performance of gravity drainage pools. Welge2 has modi- fied this approach so that the calculation time has been markedly decreased. In addition, many other authors3-9 have analyzed various phases of the gravity drainage producing mechanism during the past several years. In a high relief reservoir in which gravity may affect the recovery mechanism, there are two main types of exploitation programs which can be employed: 1. Reservoir pressure is maintained by injecting gas into the upper portions of the reservoir. In this case gas is not released from solution and, if dynamic pressure drops are small compared to the total pressure of the system, the gas and oil may be considered to be immiscible and to have constant fluid characteristics. 2. Reservoir pressure is not maintained and a "natural depletion" mechanism prevails. The term "natural depletion" can be used to describe the production history of a reservoir in which a gradual decline of average pressure and the associated release of solution gas continue throughout the producing life. In this mechanism gas is released throughout the reservoir and there is a continuous change in the characteristics of both the gas and the oil phases. It is the purpose of this paper to present the results of mathematical developments by which a method has been devised for evaluating the performance of reservoirs which are depleted by the first type of exploitation program discussed above. It should be mentioned that, although throughout the analysis gas and oil represent the two fluids existing in the reservoir, the method is equally applicable to gravity drainage in water-oil systems. STATEMENT OF PROBLEM In reservoirs of pronounced structural relief, where the closure of the oil section is great or the angle of

Jan 1, 1957

By Henry Emmett Gross, David R. Mitchell, H. E. Oehler

THE production of fluorspar is one of the smaller nonmetallic industries in the United States with a capital investment-about $10,000,000. Shipments from United States mines' in 1936 totaled 176,231 short tons valued at $3,111,268, an average price of $17.65 per ton. The United States produces about 40 per cent of the world's fluorspar, of which about 90 per cent comes from the Illinois and Kentucky deposits along the Ohio River.2 Further detailed information on the fluorspar industry in the United States is given by Hatmaker and Davis.28 Fluorspar is marketed according to the following relative quantities and specifications : [ ] The concentration of the coarser sizes presents relatively little difficulty, good recoveries being obtained with jigs and tables. However, sizes smaller than about 10 mesh cannot be successfully treated by ordinary gravity separation methods and so have been accumulating as

Jan 1, 1938