Search Documents

By T. E. Leontis

The specific effect of various rare-earth metals on the room- and elevated-temperature properties of magnesium has been evaluated. Alloys containing didymium exhibit the highest tensile and compressive strengths at room and elevated temperatures. All the rare-earth metals increase the creep resistance of extruded magnesium at temperatures in the range of 400° to 600°F, but the degree of enhancement depends on the temperature and on the concentration of the added metal. THE effects of rare-earth metals on the properties of sand-cast magnesium were discussed in some detail in earlier paper by the author.' The present paper deals with the effect of the same alloying elements on the properties of extruded magnesium. This investigation also had as its aim the development of a wrought alloy having a better combination of room-temperature strength and ductility and elevated-temperature strength and creep resistance than is found in magnesium-Mischmetal-manganese alloys, which have been reported earlier.2-5 The only known attempt to study wrought magnesium alloys containing pure cerium instead of Mischmetal was made by Mellor and Ridley.6 They found that in the form of rolled bars there is a definite, optimum cerium content for creep resistance at 200 °C and that the creep resistance of these alloys at 200 °C is significantly Improved by heat treatment at 550" to 580"C. In the present investigation the compositional variation in mechanical properties of the following alloy systems is presented: I—magnesium-Misch-metal. 2—magnesium-cerium-free Mischmetal. 3— magnesium-didymium. 4—magnesium-cerium. 5— magnesium-lanthanum. Alloys containing predominately praseodymium are not included in this series because of the lack of this material. Experimental Procedures The alloying ingredients used in preparing the alloys described herein are the same as those reported in the earlier paper.' Cerium-free Mischmetal is the rare-earth mixture remaining when the cerium is removed from Mischmetal, which contains all the rare-earth metals as they occur naturally in mon-azite sand, the ore from which Mischmetal is produced. Removal of both cerium and lanthanum from Mischmetal leaves what is commonly called "didym-ium," consisting predominantly of neodymium and praseodymium. Although the composition of the particular batch of each metal used may differ somewhat from the analysis presented previously, these differences are not great enough to warrant repeat- ing the specific composition of each material. The electrolytic magnesium used as the starting material in these alloys has the same typical analysis as that given in the earlier paper.' The alloys were prepared in small laboratory melts applying all the necessary precautions for alloying rare-earth metals with magnesium described by Marande.' Most melts were large enough to cast one 3 in. diam billet 10 in. long. In a few cases, particularly the didymium-containing alloys, the lack of sufficient amounts of the rare-earth metal limited the size of the billet to 6 to 8 in. All billets were scalped to a diameter of 2 15/16 in. and faced to a length of 9 ¼ in. as limited by the size of the extrusion container. The alloys were extruded into ½ in. diam rod on a 500-ton direct-extrusion press using a 3 in. container. The details of the extrusion step are: billet preheat, 925°F (2 hr); container temperature, 900°F; die temperature, 900°F; extrusion speed, 10 ft per min; reduction ratio, 36:1; and percent reduction, 97.3. The lower melting point of alloys containing didymium' necessitated reduction of the extrusion speed to 5 ft per min in order to prevent hot shorting during extrusion. Adequate lengths were cropped from both ends of each extruded rod to assure that all the material used for tests was extruded under uniform conditions. Tensile and compressive properties at room temperature are reported in the several conditions of heat treatment. The ASTM designations are used to distinguish these conditions as follows: T5—Direct age at 400°F (16 hr) T4—Heat treat at 950°F (4 hr) for alloys containing didymium T4—Heat treat at 1050°F (4 hr) for all other alloys T6—T4 + age at 400 °F (16 hr) The lower heat-treating temperature for alloys containing didymium is necessitated by the lower melting point of these alloys. All heat treatments were conducted in electrically heated, circulating-air furnaces. A protective atmosphere containing 0.5 to 1.0 pct sulphur dioxide was used for the high temperature heat treatments. Tension and creep specimens 6 Yz in. long and compression specimens 1½ in. long were cut from the extruded rod. A reduced section of ? in. diam was machined on the tension specimens, whereas on the creep specimens a reduced section of 0.450 in. diam

Jan 1, 1952

By F. Weinberg

Lead single crystals have been deformed in tension over the temperature range of 4.2°K to the melting point. Changes in flow stress resulting from temperature cycling and strain rate cycling have been measured as a function of temperature for crystals of different orientations and purity. It was found that the flow stress ratio, after correcting for the temperature dependence of the shear modulus, decreased progressively with temperature above approximately 0.5Tm. The activation energy calculated from the high-temperature portion of the curve was found to be markedly higher than that of self-diffusion. For single glide crystals, the corrected flow stress showed an increase above 0.5 Tm before decreasitzg with temperature. This increase is attributed to static recovery occurrittg during temperature cycling. THE temperature dependence of the flow stress, based on temperature cycling and strain rate cycling, has been extensively investigated,' and on the basis of these results dislocation models of the work-hardening process have been proposed. In general, the flow stress is divided into two parts, ts, the short-range interaction term, which is only effective at low temperatures and which decreases with increasing temperature, and TG, the long-range stress term, which is independent of temperature after allowing for the temperature dependence of the shear modulus. The observations demonstrating that tG/µ is independent of temperature were generally carried out at low temperatures to minimize recovery effects. Several investigations have been reported on flow stress measurements at high temperatures2"5 which demonstrate that TG/µ does not remain constant at temperatures above 0.5Tm (where Tm is the melting temperature of the material in OK). Specifically, Hirsch and warrington3 carried out temperature cycling tests at two strain rates on single and polycrystalline aluminum up to 0.8 Tm and on polycrystalline copper. For aluminum they found that the flow stress ratio (the flow stress at temperature T2, divided by the flow stress at the reference temperature T1 in one temperature cycle) dropped progressively with increasing temperature above 0.5Tm. From the slopes of the high-temperature portions of the curves, they determined an activation energy for the deformation process of 1.6 ev (at best) which they considered was in agreement with the activation energy of self-diffusion, 1.35 ev. Calculations of the activation volume demonstrated that the deformation was not controlled by dislocation climb. They proposed a mechanism in which the rate-controlling process at high temperatures was due to the rate of move- ment of vacancies away from jogs, i.e., that of self-diffusion. Results of Lucke and Buhler4 on single crystals of aluminum confirmed this conclusion. They measured the critical resolved shear stress of aluminum over a wide range of temperature and strain rates. They found that the temperature dependence of the critical resolved shear stress was similar to that of the flow stress ratio, as determined by Hirsch and Warrington, and from their data calculated an activation energy for high-temperature deformation of 1.35 ev identical to that of self-diffusion. More recently Gallagher5 has carried out a detailed investigation of the temperature dependence of the flow stress ratio of copper, silver, and gold. In all cases, he found that the flow stress ratio, after adjusting for the shear modulus temperature change, drops at high temperatures. The activation energies he determined were found to be appreciably higher than the activation energy of self-diffusion of the material being considered. The flow stress ratio was found to be dependent on the orientation of the material, and, in addition, an anomalous increase in the flow stress ratio for copper, oriented for single glide, was observed above 0.5Tm. The purpose of the present investigation was to measure the critical resolved shear stress, the flow stress ratio, and the strain rate sensitivity of lead, primarily as a function of temperature. The results should indicate whether, following Lucke and Buhler, the critical resolved shear stress of lead has the same temperature dependence as the flow stress, and, following Hirsch and Warrington, whether the activation energy for high-temperature deformation in lead is the same as that of self-diffusion. Lead deforms as a normal fee material,6'7 is available in high-purity form, can readily be grown as single crystals, and, for this investigation, has the very considerable advantage of having a low melting point, 327°C. The observations of the critical resolved shear stress of lead have been published elsewhere.' EXPERIMENTAL PROCEDURE The experimental procedure was essentially the same as that used in the critical resolved shear stress measurements.' Single crystals of 99.999 pct (59) and 99.9999 pct (69) lead were deformed in tension with a table-model Instron in a silicone oil bath above room temperatures and in a cooled methyl alcohol or liquid-nitrogen bath below room temperatures. The test specimens were rectangular in section, 0.65 by 0.33 cm, and had a 5-cm gage length. The specimens were grown as single crystals with tapered ends, which fitted into matched tapered grips for testing. To obtain the flow stress between two temperatures, specimens were first deformed approximately 1.0 pct at the higher temperature. The test was then stopped, the load relaxed, the oil bath removed without disturbing the specimen, the grips and specimen cooled with a fan and then immersed in liquid nitro-

Jan 1, 1969

By R. F. Sheldon

Largest uranium deposit in the Northwest is Dawn Mining Co.'s Midnite mine on the Spokane Indian B Reservation. The orebodies lie along the contact of granite and metamorphosed sedimentary rock and are controlled by faults and shear zones near the granite contact. In the oxidized zone the deposits consist mainly of the secondary uranium mineral meta-autunite; sooty uraninite and primary uranium minerals are known to occur at greater depths. Elevations in the mine area range from 2500 to 3500 ft. The rolling hills and low, rounded mountains are covered with grass and evergreen trees.

Jan 5, 1959

By H. D. Kessler, R. J. Van Thyne

Phase diagrams of the titanium-rich portion of the ternary systems from 0 to 10 wt pct Al and 0 to 1 wt pct 0, N, and C were determined. Micrographic analysis of annealed high purity arc melted alloys was the principal method of investigation and was supplemented by X-ray diffraction. TITANIUM-ALUMINUM alloys exhibit excellent properties, particularly for elevated temperature use. For this reason, the Materials Laboratory, Wright Air Development Center, sponsored an investigation of the effect of the interstitially soluble contaminants, oxygen! nitrogen, and carbon, on the Ti-A1 system. Using high purity arc melted alloys and micrographic analysis of annealed samples as the chief method of investigation, titanium-rich partial phase diagrams were determined for the ternary systems. Experimental Procedure Materials: The titanium used in the preparation of the alloys was iodide crystal bar (99.9+ pct pure) produced by the New Jersey Zinc Co. and Foote Mineral Co. The aluminum was obtained from the Aluminum Co. of America in the form of sheet. The given analysis was: Si, 0.0006 pct; Fe, 0.0005; Cu, 0.0022; Mg, 0.0003; Ca, <0.0006; Na, <0.0005; and Al, 99.99. High purity titanium dioxide purchased from the National Lead Co. was used in the preparation of the oxygen-bearing alloys. The spectrographic analysis of this material was as follows: SiO,, 0.07 pct; Fe,O,,, 0.002; A1,0,, <0.001; Sb,O,, <0.002; SnO,,, <0.001; Mg, <::0.001; Cb, <0.01; Cu, 0.0004; Pb, 0.002; Mn, <0.00005; W, <0.01; V, <0.002; Cr, <0.002; Ni, <0.001; and Mo, <0.002. Special spectroscopic graphite rod purchased from the National Carbon Co. was used in the preparation of the Ti-A1-C alloys. Alloy Preparation: Alloy ingots weighing 10 grams were melted in a nonconsumable tungsten electrode arc melting furnace using water-cooled copper hearths and a helium atmosphere. The arc was struck on a tungsten stud in the copper block to minimize contamination from the electrode. Details of the techniques have been reported.&apos;, &apos; Each ingot was inverted and remelted a minimum of four times to insure homogeneity, without opening the furnace. Remelting small control ingots of iodide titanium under similar conditions resulted in no measurable hardness increase, indicating contamination-free melting conditions were used. The alloy charges and resultant ingots were weighed to the nearest milligram. Only small weight losses were obtained upon melting, indicating that the actual compositions were very close to the nominal compositions. Check analyses substantiated this. Oxygen and nitrogen were added during ingot preparation as master alloys. An oxygen master alloy containing 25 wt pct 0 was prepared by melting iodide titanium and pressed titanium dioxide (40 pct 0) powder. The Ti-25 pct 0 alloy is more easily handled during weighing and charging than the pressed TiO, powder. Chemical analysis indicated that titanium-nitride received from an outside source contained large amounts of impurities (2.7 pct Ca). Therefore, a master alloy containing approximately 12 pct N was prepared by melting nitrided sponge titanium. As the sponge melted with difficulty, the alloy was diluted by addition of titanium to lower the melting point. The chemical analysis of the final alloy was 6.69 pct N. Both master alloys are friable and were used as —8 +16 mesh lumps resulting from crushing the ingots. NIelting the Ti-A1-0 and Ti-A1-N compositions five times produced homogeneous ingots. The preparation of homogeneous carbon-bearing alloys caused considerable difficulty. Alloys containing less than 1 pct C were prepared using spectrographic graphite rod, 1/8 in. diameter by 1/8 in. long. However, the graphite did not dissolve even with long melting times and many remelts. The ?/s in. pieces of graphite were used rather than powder because the low density powder is troublesome in arc melting.

Jan 1, 1955

By C. G. Dunn, M. Sharp

HE orientations of 137 crystals of copper pro-T duced by secondary recrystallization in a cube texture matrix have recently been obtained. Although the crystals were not prepared for the purpose of determining a secondary recrystallization texture, the orientations obtained proved to be rather interesting, as they confirmed, in part, published results and also disclosed additional preferred orientations in the texture. The investigation of Dahl and Pawlek,&apos; Bowles and Boas,&apos; and Kronberg and Wilson3 showed respectively that the orientations of secondary grains growing in a cube texture matrix were related to those of the primary grains by a rotation of approximately 30" about [001], the rolling direction, by 30" about a <111> direction, and by either 22" or 38" about a <111> direction. Kronberg and Wilson also obtained a component of the texture similar to that of Dahl and Pawlek except the angle of rotation about [001] was 19". When the cube texture matrix was deformed a small amount, Kronberg and Wilson also obtained large grains on subsequent annealing corresponding to a rotation of 15" about the normal to the sheet, but these grains should not be classified as secondary recrystallization grains since they were produced subsequent to mechanical straining. The particular texture obtained, of course, depends on the composition of the copper and the processing schedule employed, since these factors markedly affect the primary recrystallization texture and the sharpness of any cube texture produced. In the present investigation, pieces of OFHC copper in the form of M in. round bars were cold forged to a thickness of about 0.40 in., annealed 1 hr at 350°C in an atmosphere of hydrogen, and cold rolled crosswise to a thickness of 0.200 in. These pieces were given a penultimate anneal of 1 hr at 350°C in hydrogen and a 90 pct cold-rolling reduction lengthwise to a thickness of 0.020 in. Indentations generally were put in one end of the as-cold-rolled strips to promote earlier formation of secondary grains.

Jan 1, 1953

By W. D. Douglas, M. J. Hampshire, G. J. C. Young

This paper describes the replacement of a conventional filtration, clarification, and zinc precipitation plant by a carbon-in-pulp (CIP) electrowinning plant, with the objective of improving the recovery of gold from cyanide leached, acid plant calcines. The discussion covers early laboratory studies to the design and erection of the full-scale plant. Particular emphasis is placed on the problems encountered with commissioning and the strategies employed to solve them.

Jan 1, 1985

By Roswell Johnson

THE Manual of the Oil and Gas Industry, under the Revenue Act of 1918, published by the Treasury Department for the guidance of oil companies in preparing their estimates of future recoverable oil for the purpose of calculating depletion, gives the first large public collection of comparative decline curves for the whole country. It is a matter of both scientific and practical interest to so arrange these data that the pools can be readily compared. There are certain difficulties in such a comparison, however: 1. The economic limit varies from 50 to 2000 bbl. a year in different pools taken. (2) Because of this variation in economic limit, the range of data shown makes comparison possible only for wells of intermediate size. In order to be as inclusive as possible, I have taken as an expression of the rate of decline the amount of oil produced in the period during which a well drops from 3000 to 2000 bbl. a year.. No period of smaller production could be used because of the high economic limit in California; and no period of larger production and yet include the small well areas of the Appalachian. As it is, the Lima-Indiana wells are excluded. In a few instances, curves were extrapolated to obtain the reading, where the curve seemed regular enough to warrant it. In general, the amount of oil, in barrels, produced while a well declined from 3000 bbl. to 2000 bbl. a year is shown in Table 1.

Jan 1, 1920

By Frederick N. Rhines

Pure copper that has been allowed to oxidize at an elevated temperature in the air is found to be covered with two distinguishable layers of oxide scale. The outer of these, which is very thin, is composed of cuprie oxide, while the inner layer, comprising the bulk of the scale, is made up chiefly of cuprous oxide (Fig, la). If a small quantity of an alloying element, such as silicon, is present in the copper, silica particles are found disseminated through the cuprous oxide, deposited most abundantly near the metal surface, and, in addition, silica particles occur to a limited depth within the copper itself (Fig. 1b). It is this inner layer, composetl of oxide particles precipitated in a matrix of metallic copper, that is known as the "subscale" or the zone of internal oxidation. Under a low oxygen pressure it is possible to produce the subscale without the formation of external layers of copper oxides, thus leaving the metal surface bright and apparently clean while oxidation has occurred, in fact, to a considerable depth within the metal (Fig. 2). Although little is yet known in a detailed way of the mechanism of internal oxidation, the general nature of the process is evident. By virtue of the considerable solubility of oxygen in copper,&apos; it is possible to bring the alloying element in contact with oxygen within the metallic solid solution. If the oxide of the alloying element is more stable than cuprous oxide, the foreign oxide may form and, since most oxides are relatively insoluble in copper, it will not long remain in solution, but mill separate as a precipitate. As the metallic solute is exhausted in the zone of precipitation, oxygen that is constantly being supplied at the surface diffuses farther into the alloy and thus produces an ever-thickening shell of subscale. The distribution of the reacting elements in the subscale and adjoining zones must be somewhat as indicated in Fig. 3. The conditions requisite to internal oxidation to be anticipated are thus: (I) a solubility of oxygen in the alloy, (2) the ability of oxygen to diffuse at an appreciable rate into the alloy, (3) the possibility of the

Jan 1, 1940

By Frank Firmstone

IN the summer of 1881 we were forced to break up and remove the large mass of iron which had accumulated under No. 2 furnace at Glendon, in order to prepare the foundations of the new furnace which has taken its place. We used "Atlas" powder, drilling the holes with a pair of Rand drills. These worked very well when the iron was at all uniform in hardness; but this was not often the case; and it frequently happened that the holes were hopelessly blocked when but little over a foot deep. Good tamping became, therefore very important. The common method of tamping is certainly very dangerous when there is a percussion cap in the hole, and has, no doubt, caused many of the accidents attributed directly to high explosives. We found an excellent and safe method by using plaster of Paris, mixed to the proper consistency and ponred into the holes as soon as they were loaded. Clean dry sand was mixed with the plaster to reduce the quantity needed. With proper attention the tamping would set in a few minutes, and little or no more time was required than for tamping in the ordinary way. We used a "magneto" machine (Laflin and Rand) to fire the holes; and an additiollal advantage in the plan was that any risk of cutting the exploder-wires in tamping was avoided. We found it worth while to load holes not over 13 inches deep in a block 3 or 4 feet thick since the bottom of the hole was enlarged by each shot so that the next time it could be loaded more heavily, and three or four shots in this way often did as much good as a new hole twice the depth, to drill which might have taken ten or twelve hours. The rise in temperature when boiled plaster solidifies is not sufficient to ignite the exploders, as we found by repeated trials before using it in a loaded hole.

Jan 1, 1884

By Forrest F. Craig

Both early and more recent1 laboratory measurements of gas-oil relative permeabilities were made by subjecting oil-saturated cores to external gas drives. In these runs it was generally assumed that the flowing gas/oil ratio was constant at every point throughout the core. Using this assumption, the resulting equation for the gas-oil relative permeability ratio becomes A where Q is the flow rate at the producing end of the system. This relative permeability was then specified for the average saturation of the core. The assumption and resulting equation fail to recognize that in an external drive, the oil flow rate varies from zero at the injection end to a maximum at the producing end. The assumption also fails to consider the existence of a saturation gradient during an external drive. This saturation gradient is due solely to non-steady-state flow. Some authors2,3,4 have used this erroneous method of calculating relative permeability ratios from external drives. Other authors5,6,7 have used relative permeability ratios in calculating expected field performance by external drive, using Equation (1) and making the incorrect assumption that the saturation is uniform within the driven portion of the reservoir. To find the correct relation between the relative permeability. ratio at the average saturation and the produced gas/oil ratio, the insertion in Equation (1) of a factor, F, to adjust it for oil velocity gradient has been considered. The equation then takes the form Assuming that the oil velocity is directly proportional to the distance from the injection point leads to the conclusion that, for a linear system, the average oil velocity is one-half that at the producing end. Thus, the average gas/oil ratio is twice the produced gas/oil ratio, and Equation (2) is transformed into However, here again the existence of a saturation gradient is not recognized. The produced gas/oil ratio is related to the relative permeability ratio at the saturation of the outlet end of the system. It can be shown quite readily that, if the true log k,/k, saturation relationship is linear over small ranges of saturation, then d log kjko Where aaxv and u2 are the average and outlet saturations, respectively. Examination of Equation (3) shows that the factor F cannot have a single value over the whole saturation range. Another method of dealing with external drives is that of Buckley and Leverett.&apos; Their method, which assumes no gas expansion and outlet end effects, considers fully the saturation gradient present due solely to the displacement mechanism during an external drive, and applies Equation (1) to each point along this gradient. The calculation of production history using relative permeability ratio is straightforward. However, the calculation of relative permeability ratios from production history by this method is impractical. In a recent paper, Welge,1 using an approach similar to that of Buckley and Leverett, presents a simplified method for determining the saturation at the producing end of the system. At thi; saturation, the relative permeability ratio calculated by Equation (1) applies exactly, after breakthrough of the stabilizej front. By this method, relative permeability ratios or production history may be calculated with equal ease. Use of this method as a laboratory tool in determination of relative permeability ratios by external drive requires the knowledge of the total injected fluid volume; in addition to the average saturation and producing ratio. As a preliminary test of this method of calculation, laborntory external gas drives were run on a 3% in. diameter, 11 in. long sample of Nellie Bly consolidated sandstone. This core sample had a permeability of 824 md and a porosity of 28.1 per cent. The driving fluid was air. Three different oils were used, having viscosities of 1.4, 9.8, and 125 cp, respectively. The runs were made under identical pressure differentials,

Jan 1, 1952

By G. K. Burgress, H. S. Rawdon, R. W. Waltenberg, J. J. Crowe

The main objects of this investigation were to determine, from neasurements taken at representative rail mills…

Jan 1, 1915

United Engineering Trustees, Inc. W. D. B. MOTTER, JR., &apos;44 A. L. QUENEAU, &apos;45 ALBERT ROBERTS, &apos;43, President The Engineering Foundation GEORGE D. BARRON, &apos;44 F. F. COLCORD. &apos;46 A. L. QUENEAU, &apos;45, Chairman

Jan 1, 1943

By J. C. Vaughan, John Chapman

Although a considerable amount of practical importance attaches to systems involving gases and molten metals, little is known regarding the effects of alloy elements upon the solubility of gases in liquid iron. The solubilities of hydrogen1 and nitrogen2,3 in pure liquid iron arc known and it has been shown that small amounts of silicon and aluminum3 exert only a small effect upon the solubility of nitrogen but greatly increase its rate of solution. This paper presents the results of a study of the solubility of nitrogen, at pressures approximately one atmosphere, in molten iron containing up to 15.8 per cent silicon. EXPEBIMENTAL METHOD There are two general methods by which the solubility of a gas in a molten metal may be determined. In the first, which Sievertsl employed, the gas is measured from a burette into the enclosure containing the metal and the amount absorbed is found by subtracting from the total volume that of the dead space in the container. The second method, which was used successfully for pure liquid iron, is to expose the molten metal to the gas until absorption ceases, then to solidify and analyze the metal. In either method the stirring produced by inductive heating prevents the development of a stagnant layer at the metal surface and ensures actual attainment of equilibrium. Obviously the second method is accurate only when the saturated metal is capable of solidifying without gas evolution. Since the rate of solution of nitrogen in iron is increased by the presence of silicon, it was to be expected that the rate of evolution would be correspondingly increased and for this reason the first method was selected. A sketch of the furnace is shown in Fig. 1. A small high-frequency coil having 17 turns fitted closely around a fused silica tube, 2 in. in diameter, in which was placed, on a bed of 60-mesh alumina sand, an

Jan 1, 1940

By J. B. Austin

IT is now well established, chiefly through the work of Davenport and Bain,1 that the influence of temperature upon the rate of transformation of austenite to ferrite at constant temperature is represented by a curve of the type shown in Fig. 5 of Tech. Pub. 589; and the reasons for this general shape have been discussed by them in a qualitative way. Thus, the upper part, or nose, of the curve is the resultant of two factors of which the rate of change with temperature is not the same, and by analogy with other like cases it is almost certain that these factors are: (1) the chemical potential, or driving force, of the transformation, which is zero at the equilibrium temperature and increases rapidly as the temperature falls below this point; and (2) a factor analogous to viscosity, or resistance of the crystal lattice to a change in structure, which also increases as the temperature is lowered. Just below the equilibrium temperature this virtual "viscosity" of the metal is relatively low-that is, the metal offers little resistance to a change in lattice-but the driving force is also small, and the net result is that the reaction proceeds slowly. As the temperature is lowered the magnitude of both factors increases; but at first the driving force increases more rapidly than the resistance and the reaction is observed to proceed more rapidly. At lower temperatures, however, the resistance begins to increase faster than the driving force, and eventually, at the nose of the curve, overbalances it, causing the reaction to proceed more and more slowly thereafter. This concept is somewhat, though not completely, analogous to that employed in certain electrical cases where the precise factors are known and are separately measurable. The current I (in amperes or coulombs per second) flowing through a given wire is proportional to the impressed potential, or driving force E, and is inversely proportional to the resistance R of the wire; that is, I = E/R. Stated in a slightly different way,

Jan 1, 1935

By R. Y. Williams

IN the United States, fully 98 per cent. of the anthracite and bituminous coal tonnage obtained from underground operations is mined by the room-and-pillar system. Under this system, the total cost of the coal f. o. b. railroad cars contains as its greatest single item the money paid for "labor." Each labor dollar in an. average bituminous mine may be subdivided into 85 c. paid for work done inbye the gathering turnouts (including all work at the face), and 15 c. outbye that point (including all work in and under the tipple). In an average anthracite mine, the corresponding figures are 70 c. and 30 c., the larger breaker force accounting mainly for the difference between these and the bituminous figures. The next largest single item after "labor" is usually "supplies and power;" and a division of this item inbye and outbye the gathering turnouts shows somewhat the same relative proportions as has been noted under the case of "labor". During the past 10 years, the chief advances made in the coal industry have been to obtain economies through complete mechanization covering that portion of the work which lies outbye the gathering turnouts. These results have been accomplished by applying scientific principles to railroad yard layout, to cleaning and sizing machinery, to dumping facilities, to roller-bearing haulage equipment, and to heavy-rail, well-ballasted trackage. But these improvements, while gratifying in their resulting economies, apply only to 15 to 30 per cent. of the important cost items. Obviously, then, the big problem before the engineers of the coal industry today has to do with the methods of mining and the layout inbye the gathering turnouts. Four years ago, Weston Dodson & Co., Inc., determined to have an exhaustive study made of the conditions which must be met in order to gain complete face mechanization, and in order that such a mining layout would be based on, correct underlying principles. The result of that study, which was made by the writer, led to the adoption of a method of longwall mining wherein the. roof is worked on the caving system and is supported as an overhang along the face by steel jacks.

Jan 1, 1928

By H. J. Ramey

Conventional calculation of total system isothermal compressibility for a system containing a free gas phase involves, among other things, evaluation of the change of oil and gas formation volume factors and the gas in solution with pressure. Preferably, this information should be obtained from laboratory measurements made with particular oils and gases. Often, experimental measurements are not available. In this case, it is necessary to obtain pressure-volume-temperature relationships from general correlations such as those of Standing&apos; for California oils. In order to speed estimates of compressibility, generalized plots have been prepared of the change of both oil formation volume factors and gas in solution, with pressure from Standing&apos;s correlations. A generalized plot for estimating the change in the two-phase (oil and gas) formation volume factor with pressure is also presented. Usually, the effect of gas dissolved in reservoir water upon the total system compressibility is neglected for gas saturated systems, due to the low solubility of gas in water. Results of this study indicate that the increase in total system compressibility caused by solution of gas in water is often as large as the compressibility of wafer, and can be magnitudes larger for low pressure systems. Generalized results for estimating the change of gas in solution in water with pressure are presented in tabular and graphical form. INTRODUCTION During the past decade, pressure build-up and drawdown techniques have gained an important place in reservoir engineering. Build-up and drawdown analyses are only two special applications of the broad field of transient fluid-flow theory. All solutions of transient fluid-flow problems contain a parameter called the total system isothermal compressibility. This property of fluids and porous rock is a measure of the change in volume of the fluid content of porous rock with a change in pressure, and it may vary considerably with pressure. Evaluation of total system isothermal compressibility is not difficult, but it is tedious and time-consuming. Often compressibilities are estimated roughly, or transient flow methods are neglected completely. The benefits of using accurate system compressibility in properly-executed build-up or drawdown analyses are: 1. Better planning of pressure build-ups may be achieved to avoid unnecessary loss of revenue due to excessively long shut-in periods, or to shut-in periods too short to yield useable data. 2. Better and more reliable estimates of static formation pressures for reserves estimates and rate performance estimates. 3. Reliable information for evaluation of well completion effectiveness, and planning and interpretation of well stimulation efforts. The purpose of this paper is to clarify the nature of the total system isothermal compressibility, and to present useful methods for estimation of compressibility, particularly for systems containing a gas phase. DEVELOPMENT Numerous publications have presented solutions to transient single-phase flow of slightly compressible fluids, stressing pressure build-up applications. In transient flow, a compressibility* term arises to permit volume content of fluids in porous rock to change as pressure changes. The basic nature of the compressibility term is usually taken for granted. Problems arise in practical applications of transient fluid theory because most published works consider only one flowing fluid—in an ideal porous system containing only one fluid. In 1956, Perrine2 presented an intuitive extension of single-phase flow pressure build-up methods to multiphase flow conditions. Later, Martin- established conditions under which Perrine&apos;s multiphase build-up method had a theoretical foundation. Perrine has shown that improper use of single-phase build-up analysis in certain multiphase flow situations can lead to gross errors in estimated static formation pressure, permeability and well condition. It is likely that, much pressure build-up data for oil wells should be analyzed on the basis of multiphase flow. For both single-phase and multiphase build-up analysis, the isothermal compressibility term in dimensionless time groups often should be interpreted as the total system compressibility. All real reservoirs contain one or more compressible fluid phases. In addition, rock compressibility can contribute in an important way to the total system compressibility. The proper total system compressibility expression may contain terms for compressibility of oil, gas, water, reservoir rock and terms for the change of solubility of gas in liquid phases.

Jan 1, 1965

By R. C. Good

Slag control for any kind of steel, rimming, straight carbon or alloy, should start with the charge and be developed well in advance of the tap because its composition, viscosity and temperature will unquestionably govern the physical and chemical properties of the steel when tapped. In the majority of plants producing alloy steels, primary consideration is given to the chemical specifications; physical characteristics usually occupy secondary place in the melter&apos;s mind. Recently, however, buyers have indicated limits of machinability, hardenability, grain size and, of course, always wanted steel free from foreign nonmetallic inclusions. It is these latter specifications that require the attention of the operator to the slag and its control. The slag must act as a vehicle for oxidized elements originating from the metallic portion of the charge; it should hold the oxides of phosphorus, silicon, manganese, iron and chromium that come into contact with it either before or after the refining and finishing stage of the heat. It must be used as a transferring medium of oxygen from the atmosphere or oxide additions to the metal and should permit a free escape of gas generated within the charge. Finally, the slag is the principal controlling factor in regulating the rate of oxidation which in turn eventually determines the quality of the steel as measured for the various characteristics mentioned above. With pig iron of uniform composition, the iron oxide in the slag increases as the limestone is increased but with the same addition of stone in every heat, the iron oxide decreases as the silicon is increased in the charge, and vice versa.

Jan 1, 1935

By Orrin Peterson

THE decision of the Supreme Court of the United States not to review the findings of the lower courts closes an interesting chapter in the mining litigation that has arisen as a result of the extralateral feature of the mining law. The time seems opportune to record some of the important geological features, and also some of the legal features, of the controversy, in the hope that these will be permanently accessible to members of the mining profession. After many rumors of litigation, the Utah Consolidated Mining Co. sued its neighbor for the ore that had been, it was alleged, wrongfully extracted from its so-called Yampa limestone lode. This ore lay beneath Utah-Apex surface and was claimed by virtue of the extralateral rights conferred on the Utah Consolidated Co. through the ownership of certain specific mining claims, one of the principal claims being the Yampa. Previous to bringing suit, the Utah Consolidated Co. had strengthened its position by purchasing the Old Yampa mine and by making an agreement with the Utah Metal & Tunnel Co., which gave it clearer title to the outcrop of the Highland Boy limestone. Access to the workings of the Utah-Apex Co. was secured and reciprocal privileges gave Utah-Apex representatives the right to enter the properties of the Utah Consolidated Co. This resulted in the Utah-Apex immediately bringing countersuit for ore alleged to have been wrongfully extracted from under its surface in the Leadville country, see Fig. 4. Six cases came up for consideration: five related to the original suit and the countersuit, and one related to the Dana extralateral claims of the Utah-Apex Co.

Jan 6, 1924

By W. C. Kelly, E. J. Essene, A. M. Affifi

Occurrences and associations of natural tellurides are constrained by the relative fugacities of Te, in specific mineralizing environments. Some are rare (e.g., FeTe2) and others absent (e.g. MoTe , ZnTe) m nature because high f-Te2/f-S2 ratios are rare or unattainable , whereas others (e. g . , Ag2Te,HgTe) require lower ratios and are common. Complex and seemingly chaotic sulfide-telluride associations are, in fact, highly systematic and depend both on temperature and fugacity ratios. Some older sulfides act as buffers via reactions such as PbS + Te2 = PbTe + S2, thereby affecting the deposition and paragenesis of younger tellurides and the combined or uncombined mode of occurrence of precious metals. Thermochemical calculations of telluride-sulfide-oxide equilibria can have pragmatic value. The thermochemical approach tells us little about the Te "source", but is beginning to unravel the systematics of telluride mineralogy and controls at the precipitational end of the line.

Jan 1, 1985

By C. F. Willis

Many of the failures in vocational education are due to the fact that the educational methods were not designed to the capabilities, habits, and environments of those to be trained; rather they were based on the policy that education is education and lessons are lessons, whether for youngsters of fifteen or for men of forty. Vocational education among miners involves, first, a study of the men themselves, their habits, and the use of their leisure time; second, a study of the differences between the methods of teaching required for men and for children. Certain fundamental requirements of training methods for miners are reasonably universal and may be applied with success to any ordinary mining community. The rate of labor turnover is another consideration; it would be useless to design a four-year course for men who remain in one place only a few months. Length of Course The first consideration should be the length of the course. Few mining communities have a sufficiently stable population to make it possible successfully to carry on a course for over a year. While some men might complete a four-year course, the number is comparatively small compared with the number to whom a shorter course would be of service, and it is better to raise the standards of education even a little for a large number than to raise them to a high level for a few. It is perfectly possible to attain both objectives by arranging the courses in small units; all the units, when grouped together, should comprise a fairly complete course, yet any one unit should be complete in itself and of benefit to the workman. It should not take many of these units to make a miner or a timberman out of a mucker; but to do this the course should be short, because muckers seldom stay in one place long. By grouping a number of these units together it Would be possible for a miner to become a shift boss or a shift boss a foreman, and so on. As far as possible the units of the course should not be dependent on those preceding or following. The workman understands the completed job but he is not accustomed to carrying on several jobs at the same time and

Jan 1, 1920