Search Documents

By J. A. Herbst, K. Rajamani

INTRODUCTION Recent research has shown that popu- lation balance models hold considerabl e promise as a basis for accurate mill scale-up from laboratory batch grinding tests. It has been shown that entire product size distributions from large ball mills can be predicted from data obtained in tests in small mills with errors of less than one or two percent. This level of accuracy has been demonstrated for batch grinding scale-up (Herbst and Fuerstenau, 1980; Austin, 1973; and Malghan and Fuerstenau, 1976) and for continuous grinding scale-up (Herbst, et a1., 1976; Herbst, Rajamani and Sanchez, 1982; and Herbst, Rajamani and Lo, 1982) in commercial mills up to 14.5 x 32 feet. A procedure which has been proposed for commercial mill design using the population balance approach and specific power information is shown in Figure 1 (Herbst and Fuerstenau, 1980). Here batch grinding data (size distributions for various energy inputs) obtained in a small batch mill is input to an estimation program which determines the "best" set of breakage rate parameters from the data provided. In turn, these breakage rate parameters are input to a scale-up program along with traditional inputs such as: a) desired circuit throughput and product size b) circuit operating conditions including fraction of critical speed and fractional ball load, size distribution and % solids in feed and circulating load (if closed circuit). In addition, since the population balance approach relies on more detailed models of the grinding circuit sub- processes than the classical design methods do, it is necessary to provide input to the scale-up program on the nature of material transport through the mill (e.g. residence time distribution information) and classifier performance characteristics (e .g. selectivity functions). The scale-up program will make the design calculations including the selection of mill dimensions and drive requirements, will predict product size distributions throughout the commercial circuit and will provide information on the sensitivity of the design to errors in the design assumptions. In order to implement such a scale- up scheme it is necessary to have a computer program for parameter estimation and a program for scale-up prediction. A program which is suitable for parameter estimation, ESTIMILL, has been developed and tested on a wide variety of ores at the University of Utah. This program has been in use in

Jan 1, 1982

By H. B. Fuqua, B. E. Thompson

For a very brief description of the North Texas area and the general geological features with which it is associated, the reader is referred to the summary for 1935. As in previous years, the authors have been unable to undertakc the almost impossible task of isolating statistics for the hundreds of productive "spots" which are included within the generally productive areas of the several counties. However, pools that appear to be definitely isolated—as, for example, the Foard County production and the new pool recently developed southeast of Gainesville in Cooke County—are covered separately. During the year 1936, both routine development in proven or scmi-proven areas and exploratory drilling showed a decrease over the year 1935, there having been a total of 1453 wells drilled in the district during 1936, as compared to 1619 in 1935. It is also of interest to note that abandonments exceeded completions in 1936. Developments during 1936 While a number of local productive spots were found in Wilbarger, Archer and Wichita Counties, and numerous minor local extensions to older producing areas were developed in practically all the producing countics in the district, only two discoveries of sufficient importance to justify special mention were made. Anderson and Kerr No. 1 Bruhlmeyer, about two miles southeast of Gainesville in Cooke County, was completed in April, at a total depth of 2014 ft., for an initial production of 315 bbl. daily from a sand of Pennsylvanian (Canyon) age. Development has been rapid and the field is about drilled up. During November the 100 wells in the field averaged about 40 bbl daily. The structure appears to be a small fold associated with the northeast flank of the main uplift, which extends in a northwest-southeast direction across Cooke and Montague Counties.

Jan 1, 1937

By Charles R. Keyes

Prefatory,........323 Foundation of classificatory schemes in general..325 Past opinion on the classification of ore-bodies,.326 Nature of ore-deposits,....... 326 Definition........326 Fundamental law of origin.... 327 Significance of ore-bodies,.... 327 Date of origin........328 Original source of ores..... 328 Alteration of ore-bodies,....329 General methods of ore-formation.... 330 Ascension verm lateral secretion... 330 Replacement.......330 General factors in classification....332 Genesis in ore-classification....332 Literature of ore-deposits...... . 333 Criteria of ore-classification,..... 335 Primary grouping of ore-deposits..... 338 Hypotaxic deposits......341 Eutaxic deposits...... 341 Ataxic deposits....... 313 Secondary categories of ore-bodies....343 Ternary phases of ore-deposition.....344 Types of hypotaxic or surface deposits..... 344 Illustrations of eutaxic ore-bodies.... 347 Examples of ataxic ore-bodies.....352 Recapitulation.. .. .. .. 355 Prefatory. Much has been written on the genesis and classification of ore-deposits. Much remains yet to be written on the subject

Jan 1, 1901

By George S. Rice

The subject of violent bumps in coal mines has been again brought to attention by a recent succession of such occurrences in the coal mines of the Cumberland field of eastern Kentucky and southern Virginia, which have caused fatalities and injuries to underground employees, a report on which is being issued by the United States Bureau of Mines1. The A.I.M.E. has had two valuable papers on bumps in the No. 2 Mine, Springhill, Nova Scotia, each followed by general discussion on bumps and their causes2. This paper gives a brief review of suggested causes and remedial measures given in English, Canadian and United States reports on blimps in coal mines, and then presents suggestions arising from the writer's recent investigation of the bumps in the Cumberland mines, made at the request of the mine operators, to determine the causes and remedies. These bumps, which occur under the simplest natural conditions, provide better opportunity for analysis of causes and effects than afforded under more complex conditions. The simple conditions in this field consist of relatively thin and level coal beds and uniform roof strata free from folding and faulting. Definition of Bumps Bumps in coal mines, as defined in this paper, are sudden violent bursts of coal that usually occur without warning in the extraction of pillars and may or may not be accompanied incidentally by falls of draw slate, upheaval of bottom and smashing of timbers. They are not known to occur where the advancing longwall method of mining, accompanied by

Jan 1, 1936

By Frank Kneeland

SAFETY FIRST is a popular motto-most mining companies have adopted it. It is probable, however, that in the majority of cases it is only a motto and gets no further than the office stationery or the bulletin board at the mine's entrance. In but few industries is there employed a greater diversity of machinery and mechanical devices than in coal mining. The list ranges all the way from mechanical stokers to wood-working machinery and undercutters. Many of these devices, particularly those employed in wood working, are extremely dangerous. In 1913, 23 per cent. of all fatalities occurring in coal mining in the U. S. were caused by machinery of some sort or other. Although the forms of accidents occurring with mining machinery are legion, they generally arise from one or more of five causes: (a) Falls from ladders, platforms, etc.; (b) coming in contact with moving machines or parts thereof; (c) electric shocks; (d) failure of some machine part; (e) mismanipulation of valves, levers, switches or other hand-operated controlling devices. The steps which may be taken to prevent accidents from the above causes are almost as numerous as the accidents themselves. There is, and can be, no panacea for all mishaps, nor for any one class of accidents. There is no mathematical or other formula that will bring immunity under any set of conditions. Common sense is the only guide. The remedy for the first-named class of accidents is simple and generally effective-namely, make the staging, ladder, platform, or other support, abundantly strong to carry any possible weight that it may be called upon to bear; provide ample railings on platforms or runways, and non-slipping feet on movable ladders.

Jan 1, 1915

By Alfonso Rizo-Patrón, A. M. Gaudin

Previous studies of activation in flotation have directed attention to the action of the activator on the mineral to be floated rather than to the relationship of the activator to the collector. The latter phase of the problem, however, seems to have definite scientific, if not also practical, interest. In the investigation reported in this paper, experiments were carried out, largely with quartz as subject, barium as activator, and oleate as collector. The results obtained indicate that a I: I ratio of collector ion to activator ion gives optimum results, and that a 2:1 ratio almost fails to achieve activation and flotation. Yet, a 2:I ratio would have been expected on stoichiometric grounds, had the coating been a normal salt of the activator ion with the collector ion, since barium is a divalent cation and oleate a monovalent anion. To interpret and rationalize the observations, considerations of the crystal chemistry of quartz are helpful. The point of view to which these considerations lead may be of general applicability to systems involving suspensions of solids in liquids; they confirm that an adsorbed coating is inescapable. Apparatus and Supplies The experimental work consisted in barium-ion abstraction tests, hydrogen-ion and hydroxyl-ion abstraction tests, flotation tests, and determinations of the surface of the crushed quartz. The flotation machine was built according to the design of D. W. McGlashan.* It consists of a drill press in which the bit has been replaced by a stainless-steel impellor surrounding a stainless-steel sta-tor, as in the Fagergren laboratory machine. The air intake is controlled by a valve, and the cell consists of a beaker. The quartz was obtained from vein quartz stored in large chunks. It was first crushed to 20 mesh, then sized on a 28-mesh screen. The 20 to 28-mesh size alone was retained for use. This size was freed of coarse iron by passage through a Ball-Norton magnetic separator, bleached with boiling hydrochloric acid to remove residual abraded iron, washed with distilled water until the washings were thoroughly free of ferrous, ferric, and excess hydrogen ion, and stored in covered Pyrex beakers under water until used. The barium was used as barium chloride, Baker's analyzed C. P. The oleate was used as sodium oleate. It was prepared from sodium hydroxide, Baker's analyzed C. P., and oleic acid purified by R. R. de Arellano3 in the laboratories at the Massachusetts Institute of Technology. The purification procedure was elaborated from the recent $researches of Brown and Shinowara.2 It consisted in: (I) saponification of olive oil with potassium

Jan 1, 1943

By C. H. Jr. Herty

The results of a study of the open-hearth process from the physicochemical view-point are given. This study includes experimentation in small laboratory furnaces and in standard 100-ton furnaces. The behavior of manganese, carbon, and phosphorus are quantitatively explained. The action of "residual" manganese is discussed with reference to its relation to iron oxide dissolved in the metal. The solubility of CO in steel and its relation to dissolved FeO and carbon is given. The equation for phosphorus elimination has been tested out on a 200-ton furnace and the results are given in the text. THE effect of temperature and slag composition on the elimination of metalloids in the basic open-hearth process has been qualitatively understood since the early days of steel making. The quantitative effect has, however, only recently been brought to attention. The effect of slag composition has received more attention than that of temperature, primarily because the range of finishing temperatures in the basic open-hearth process is small compared to the large variations found in the composition of the slag at different periods during the process, and to the variations occurring with the use of raw materials of different degrees of impurity. The effect of slag composition on the elimination of metalloids has been studied by Styri1 from the thermochemical standpoint. This method is open to serious errors, in that thermochemical data at 2900° F. are very inaccurate and in many cases completely lacking. Feild2 has calculated equilibrium constants from the rate at which the metalloids are eliminated. The effect of slag viscosity on rate of elimination will affect the constants calculated by this method. Whitely,3 Colcough4 and others have used slag compositions as the basis for calculation of constants by which the extent of elimination may be calculated.

Jan 2, 1926

Aamot, Olav Crone, Chem. Engr., Norsk Elektrokemisk, Kongensgt. 18, Olso. Norway. '29 Abadilla.-Quirico A., Dir., Bureau of Mines Manila, P. I. '38 Abbott, Clarence E., V.P., Charge of Raw Materials, Tennessee Coal, Iron & R.R. Co., 1212 Brown-Marx Bldg., Birmingham, Ala. '04 Abel, Raymond L., Prof., Dept. of Pet. Refin., Univ. of Pittsburgh Pittsburgh, Pa. '29 Abel. Walter D., Cons. Engr 1839 Holmby Ave., W. Los Angeles. Calif. '32 Abele, Louis T R. F. D. 5. Susquehanna Trail, N., York. Pa. '31 Abell, Leo M., Ore Dressing Investigator, School of Mines Adelaide, S. Australia. '31 Abenius. Hakan V., Mine Supt., Bolidens Gruvaktiebolag Boliden, Sweden. '37 Aborn, Robert H., Asst Met., Research Lab., U. S. Steel Corp. Lincoln Highway, Kearny, N. J. '19 Abraham, W. E. V., East India United Service-Club, 16 St. James' Sq., London, S. W. 1, England. '28 Abrams. Charles Jackson 1624 17th St., Denver, Colo. '36 Abstein, Henry T., Engr. & Mgr., Profile-Tamarack Mines Co Yellow Pine, Idaho. '27

Jan 1, 1938

It was customary formerly to publish an index of the Transactions about every fifth volume, but since the Institute began in 1913 to publish three volumes instead of one volume per year, this has been deemed impracticable and unnecessary. No collective index has been published since the one covering Volumes I to XXXV inclusive, excepting a short one covering Volumes XXXVI to XL inclusive. The Board of Directors, therefore, upon the recommendation of the Committee on Papers and Publications, decided to publish this index of Volumes XXXVI to LV inclusive, and thus enable members to have in condensed space the collective indexes of all the volumes of the Transactions.

Jan 1, 1918

By Robert W. Bartlett

A computer model for predicting the rate of oxidative leaching of copper from fragmented low grade sulfide ores is presented. The model involves the kinetics of the dissolution of chalcopyrite grains and solution diffusion of oxygen within rock pores. Adjustable curve fitting parameters are not used. The model was tested by comparing computed extraction curves with experimental results for a -11 inch ore obtained by block caving and leached at 90°C and 400 psi oxygen for one year at the Lawrence Livermore Laboratories.

Jan 1, 1973

By L. S. Kolbert, C. H. Baab

Introduction In June 1981, the Electric Power Research Institute (EPRI) issued a report titled "Control Systems in Coal Preparation Plants" to determine the status of instrumentation and automation systems in the coal preparation industry. EPRI concluded that the control systems presently being employed in the US coal preparation plants "are relatively primitive compared with those in other mineral processing industries; and analytical instrumentation is virtually non-existent." With tighter specifications on the quality of steam coal, interest is increasing in more sophisticated control systems. One type of device that is currently assisting the preparation plant operator optimize and control the coal cleaning process is nuclear based instrumentation. Nuclear instrumentation includes methods for measuring weight, level, and density as well as for performing elemental analysis on coal. Major Features and Benefits of Nuclear Measurement and Analysis Systems There are many features and benefits of nuclear instrumentation. The major benefit is that nuclear instrumentation is non-contacting. The measuring heads do not contact the process materials. This enables measurements of corrosive, abrasive, or high temperature materials with no loss of performance, reliability, or useful life. Also, there are no moving parts to wear or be fouled by dust or corrosion. Installation is simple and inexpensive. For instance, density gauges are simply clamped onto existing pipe runs. Weigh scales and level switches usually require nothing more than welding brackets to customers' equipment. Once installed, routine maintenance can be performed without interrupting the process. Thus, nuclear instrumentation is highly reliable and easily installed and maintained. The operating life of the instrumentation is virtually unlimited. Principle of Operation Nuclear belt weigh scales, point level switches and density gauges all operate on the gamma-ray transmission principle. A beam of gamma radiation from a radioisotopic source is projected through the process material either on a belt, in a vessel, or in a pipe. Opposite the source is a radiation detector whose electrical output is proportional to the intensity of the radiation it absorbs. Gamma radiation is part of the same electromagnetic spectrum that encompasses light, infrared, and x-rays. In many respects, gamma radiation behaves much like light. However, it is far more penetrating and can be transmitted through considerable thickness of materials that are opaque to visible light, e.g., several inches of steel. Types of Nuclear Instrumentation in Coal Preparation Plants There are four types of nuclear instrumentation presently being employed in coal preparation plants. They are: •Belt Weigh Scales •Point Level Switches •Density Gauges •Coal Analysis Equipment. Each type of instrumentation has a number of potential applications within the plant. What follows is a discussion of three different types of devices and their applications. Weigh Scales In coal preparation plants, weighing instruments are used for measuring material throughput, totalized weight, and batch weight on conveyor belts and other transport equipment. They are also used on drag chain conveyors, vibrating conveyors, and screw conveyors. Weighing is important for receiving the run-of-mine coal, controlling mass flow, scheduling production, and loading and shipping the washed coal to market. There are two basic types of weighing instruments: gravimetric and nongravimetric devices. Gravimetric devices are units which measure the pull of gravity on the material being weighed. Nongravimetric devices are not dependent on the force of gravity on the sample. Nuclear weigh scales are the most prevalent nongravimetric devices used. The nuclear weigh scale works on the same basic principle as other nuclear gauges. The greater the quantity of material placed in the path of a radiation beam, the more radiation will be absorbed by the material. In weigh scales, Cesium 137 source is generally placed above the moving stream of material so that the radiation is directed through the material. An ion chamber radiation detector is on the opposite side of the material. The radiation passing to the detector generates a signal which is inversely proportional to the weight of the material present. This signal is amplified and integrated with the speed of the process flow yielding the weight. The weight is indicated and can be totalized for throughput, batch control, etc. In conclusion, radiation weighing methods have become well established in the coal preparation industry throughout the world. As mentioned before, this device finds its most

Jan 1, 1985

By Joseph Zwierzycki

By an extension of drilling activities in 1938, the Polish oil industry succeeded not only in maintaining production but even in increasing it slightly. This increase, however, was from present oil reserves and not due to the discovery of any new fields. Most of the new wells were drilled in the Jaslo district, particularly in the Lipinki-Libuszal oil field, because of the shallow depth of the producing sands. At the Boryslaw field the 12,332 meters drilled could not compensate for the steady drop in production. A drilling campaign similar to that of the previous year in the Stanislawow district resulted in a slight decline of production. A number of the new wells have been subsidized by the Fund for the Advancement of Drilling2 in Poland. As the present sums at the disposal of this fund are insufficient for a great exploration program, they are chiefly used for the maintenance of the actual production. New wells on known folds, but more than 1000 m. outside the present productive areas, are entitled to a subsidy. Applications for wildcats outside the known productive areas have not been received in 1938. Even when the Polish oil industry was prosperous, wildcatting was not frequent and in their present impoverished condition the oil companies are no longer able to bear such financial burdens. The only way to start a large-scale drilling campaign on the still existing promising areas seems to depend on the granting of new substantial subsidies from the Treasury. Such measures are being considered by the Polish Government. It has been suggested that a fund for wildcatting might be raised by a small increase in the price of benzine. An advance of one grosz per liter of benzine would raise, on present home consumption of 108,000 kilogram-tons, about 1.3 million zloty, an advance of 5 grosze more than 6 million zloty.3 This small increase in price would hardly be felt by the motor-car owners, as it would mean an extra expense of 80 to 400 zloty in a year.

Jan 1, 1939

By Robert A. Melton

Since many of the easily mined, continuous, thick coal seams in the Appalachian Region have been exhausted, new exploration and mining is being directed toward less continuous seams that are under more cover and are more difficult to mine. The direct results of this are that more money and time and more expertise and data are needed to plan and open new coal mines today. It is also becoming apparent that the old methods of assimilating and preparing information needed for mine planning are inadequate to meet the needs of today's modern mining engineer, especially in the areas of data gathering, storage, retrieval, preparation, and interpretation. The system described here allows assimilation of old and new core data in a relatively quick, accurate, and efficient manner. The system is a set of computer assisted procedures consisting of the following four basic steps: 1) raw data collection, computer input, storage, and graphic preparation, 2) geologic profile correlation and establishment of seam continuity, 3) computerized data posting of important seam parameters, 4) geologic and planimetric analysis for mine planning.

Jan 1, 1977

By S. Floreen, R. M. Pilliar, H. W. Hayden

The fracture behavior of a 50 pct Cu-50 pct Fe mi-croduplex alloy, laminated composites of copper and iron and an extruded 50-50 Cu-Fe elemental powder composite was studied. Very low ductile-brittle transition temperatures were achieved in all cases, but for different reasons. In the microduplex alloy both the initiation and also the propagation of cleavage fractures appeared retarded by the very small in-terphase distances. In the composites, crack propagation through the sumples was prevented in most cases by delamination fractures perpendicular to the advancing cracks. These delaminations occurred at different regions and by different mechanisms in the various composites. In the extruded powder composite, de-lamination appeared to take place along preexisting flaws. In the crack arrest geometry of the laminated plates, delamination took place by localized shear fractures within the copper near the Fe-Cu interfaces. In this case delamination was enhanced by thicker laminate layers, and by having the resistance to shear failure of the copper sufficiently low compared to the toughness of the iron. BRITTLE fracture in engineering materials has long been a problem, and many different ways of preventing it have been considered. One method that has been of growing interest lately is to prevent crack propagation by the introduction of mechanical discontinuities into the structure. These discontinuities may act in several ways. They may simply act as crack stoppers. They may introduce secondary fractures such as de-laminations that deflect the initial crack into new, less damaging directions. Alternatively, they may subdivide a fairly large bulk sample that would have been loaded in plane strain, for example, into a number of subunits that are individually loaded in plane stress and thus are more resistant to fracture. Other mechanisms, or combinations of mechanisms, are also feasible. A number of methods exist for introducing mechanical discontinuities into a structure. Composites by their nature have discontinuities in structure, and numerous studies have shown that fracture propagation in materials of this type can be radically changed by suitable control of the composite parameters. Of particular significance to the present work are recent investigations of layered composites made by joining high strength steel sheets by various means.'-4 These studies have shown that through proper control of the mechanical properties of the bonds joining the sheets it was possible to introduce delamination fractures that markedly improved the overall toughness of the composites and in some cases completely prevented through-the-thickness fractures. Another technique for introducing structural discontinuities is simply to use a two-phase alloy. It has been recognized for many years that a small amount of a second phase may improve toughness either by homogenizing plastic flow and thus preventing localized stress concentrations that nucleate fracture, or by interacting with an advancing crack. In most of these studies of two-phase materials, the decreases in ductile-brittle transition temperatures produced by the second phase were relatively small. More recently, work on two-phase stainless steels having a very fine grain microduplex structure has shown that the presence of on the order of 40 to 50 pct of a tougher second phase may lower the ductile-brittle transition temperature of the brittle phase by approximately 300°F. 5-7 In these alloys delaminations were seldom observed. The tougher second phase appeared to minimize the ease of both the initiation and the propagation of cleavage fractures. These results show that both the composite approach and the microduplex alloy approach are effective methods of preventing brittle fracture. Therefore, it was of interest to compare the fracture behavior of a microduplex alloy with composites made from the two-phases that were present in the alloy. To simplify this comparison the 50 pct Cu-50 pct Fe system was selected for study. At low temperatures the equilibrium tie line phases in this system are essentially pure ferrite and pure copper. A 50-50 alloy was cast and hot worked to produce a microduplex structure. Two types of composites were studied; laminated structures prepared by roll bonding iron and copper sheets of the tie line compositions, and an extruded powder composite made from high purity elemental powders. The fracture behavior of these materials was then compared. EXPERIMENTAL PROCEDURE Alloy Preparation. The 50-50 Fe-Cu alloy and the components for the roll bonded composites were prepared by vacuum induction melting 30-lb heats using electrolytic grades of iron and copper as charge materials. A carbon boil was used to deoxidize the melts. Small additions of copper and iron were made to the iron and copper heats, respectively, to approximate

Jan 1, 1970

Stripping of the Exotica open-pit mine, which is proceeding at about 120,000 tpd, is dwarfed by its proximity to the 500-million-ton Chuquicamata tailing pile. The excavating work is being carried on smoothly and efficiently and, as of the end of October, accounts for the removal of 77 million tons of total material of which some 200,000 tons is stockpiled ore. Diamond drilling has outlined an orebody 5900 ft long and 3400 ft wide containing an estimated 153 million tons of ore at 1.35% recoverable copper based on 80 % extraction.

Jan 11, 1969

By Dorsey A. Lyon, Robert M. Keeney

The utilization of hydro-electriic power in electro-metallurgical industries, aside from purely mechanical operations, may be of two kinds. The electric energy may be used to supply the heat necessary for the performance of the chemical reactions of a metallurgical process, or the electrolytic action of a direct current may be employed for extraction of metals, either in a reduction process or a refining process. In discussing this subject, it is well to distinguish between established industries, which are producing metals and alloys at a, profit by use of the electric current, and the many processes which are either still in the experimental stage or have not even passed the paper stage of development of a patent. That is, we consider electro-metallurgical industries as commercial operations which are now consuming large blocks of electric energy, while processes which are not in commercial operation are only prospective consumers. Also, owing to the difliculty and risk of any attempt to foresee the effect of the European war upon electro-metallurgical industries, we have felt obliged to disregard the war entirely, and state our opinions regardless of its existence. Application of Electric Energy to Metallurgy Disregarding electrolytic refining processes, the applications of electric energy to metallurgy, when considered from a commercial viewpoint, may be classified as follows: Industries Experimental Processes Manufacture of aluminum Electric-furnace smelting of: Electric-furnace manufacture of: Ferro-alloys Copper ore Pig iron Zinc ore Steel In this paper only the above industries and experimental processes will be considered as possible consumers of hydro-electric power in large quan-

Jan 1, 1916

By Howard L. Hartman

There is reason to believe that ventilation systems so far devised for use with continuous mining machines fall far short of success. This is vividly demonstrated to anyone who has observed in a continuous miner section the localized ignitions of pockets of gas and the generation of dense clouds of dust by the cutting head of the machine. The alarming frequency with which major ignitions and disasters continue to occur in modern mechanical mining and the rise in incidence of pneumoconiosis serve as reminders that our ventilation systems are far from achieving the ultimate in providing protection from either short-term explosions or long- term dust diseases, both of which take lives. Human safety is the main concern in ventilation. But in this day of high-priced labor, let us not forget human comfort, either, for this is a major factor in motivation toward high productivity. The failure or inadequacy of most mine ventilation systems in providing the kind of working conditions at the face that are conducive to productive as well as safe operation is an indictment of our environ- mental control program in mining generally.

Jan 3, 1962

By Henry S. Brown, Jean E. Tilden

Pyrite, pyrrhotite, chalcopyrite, and sphalerite from deposits distributed within the Piedmont and Blue Ridge provinces of North Carolina and adjacent areas were examined by atomic absorption spectrophotometry for cobalt, nickel, manganese, lead, tin, chromium, molybdenum, and gold. The ore samples were also examined petrographically. Cobalt and nickel, in general, enter pyrite and pyrrhotite rather than chalcopyrite and sphalerite. Manganese generally enters sphalerite rather than the other phases where an alternative is possible. The presence of tin in sulfide minerals was noted in a group of deposits east of the known occurrences of tin oxide (cassiterite) in the Kings Mountain belt, which may indicate the presence of a more extensive tin belt in the southeastern Piedmont than was previously recognized. Pyrrhotite from a group of four deposits in Jackson and Clay Counties, North Carolina, differs from pyrrhotite from other Ducktown-type deposits in having cobalt/ nickel ratios less than one, finer grain sizes, and colloform texture. These differences suggest that that this group of deposits has had a history different from that of the other Ducktown-type deposits studied. No significant conclusions could be made based on the distribution of lead, chromium, molybdenum, or gold.

Jan 1, 1975

By Wayne D. Gould

Cities Service Co.'s Pinto Valley concentrator was designed to eliminate excess capital costs without loss of efficiency. The result is a workable plant with some important innovations. These innovations, the equipment used, and plant processes are outlined. Particular attention is paid to the work efficiency and wear of the six ball mills, the largest wet ball mills made. For experiment purposes, four designs of liners were installed. The effectiveness of each design is discussed.

Jan 1, 1977

By Felix G. Berra, David H. Orr

The first large scale application of radio remote control equipment to standard gage railroad trains has been achieved at the Morenci mine of Phelps Dodge Corp. at Morenci, Ariz. Twenty or more ore and waste haulage trains are remote control operated at any one time, each with a one-man crew. Reduction of train crews from two men to one man has materially lowered the total cost of train operation. Elimination of brakemen has also resulted in an improvement in train efficiency brought about by a shortening of train haulage cycle times.

Jan 4, 1965