Search Documents

By J. A. Bownocker

THE production of oil in Ohio, in 1924, was characterized by no marked or surprising change. Low prices and the absence of promising territory made the year quiet. As is well known, Ohio has reached a state of "settled production," and the most that can be expected for the ensuing few years is to maintain the output at approximately the present figure 1921 7,335,000 1922 6,781,000 1923 7,085,000 Geographically, the Ohio fields may be divided into three areas, each of which gets its main supply of oil from a different stratigraphic horizon.

Jan 3, 1925

David H. Browne was born June 8, 1864; at Hollymount, County Mayo, Ireland. At the age of 16, after going through the Londonderry Academy; he came to this country, and entered the University of Michigan, where he was graduated in 1885. He began his scientific practice as chemist, under F. A. Emmerton, in the laboratory of the Joliet Steel Co., after which he served some time as chemist at the Ludington mine, Iron Mountain, Mich. But in 1888 he went back for a year to his alma mater as instructor in inorganic analysis. Those who knew him feel sure that he would have been an efficient and popular professor; but his ardent temperament could not brook the rnonotony and confinement of the class- room; and in 1899 he went to work at the Andrews and Hitchcock blast-furnaces, at Hubbard, Ohio, where he remained until 1891, when he entered as chemist the service of the newly organized Canadian Copper Co., operating in the Sudbury district, Canada. This was the beginning of his special professional life-work. For twenty-six years he devoted himself to the numerous and complex problems successively arising in connection with the metallurgical treatment of the nickel-copper ores of Sudbury. One of his notable achievements was the development of an electro-lytic process for the separation of nickel and copper in the ores referred to. This method was successfully employed for several years; but when the Canadian Copper Co. was absorbed by the International Nickel Co., the cheaper Orford process owned by the latter was substituted. . A still more permanently important piece of metallurgical progress credited to Mr. Browne was the successful firing of reverberatory smelting-furnaces with powdered coal-a measure which had been desired, dreamed and attempted by others, but which he was acknowledged as first to put in practice on a large scale. The Engineering and Mining Journal of April 7, 1917, says editorially of this improvement:

Jan 6, 1917

By E. Buehler

THE floating zone refining technique'-4 has provided a new experimental approach to the purification of many reactive materials especially those with high melting points. The method avoids the use of a crucible and at the same time it provides a favorable environment at the freezing interface for the growth of single crystals. The physical properties of refractory metals such as molybdenum and tungsten have long been of interest from a fundamental point of view and because of their widespread use in vacuum electronics. Single crystals are often desirable for study. Prior to the introduction of zone melting, single crystals of these metals were usually grown in the solid state at temperatures slightly below the melting point by strain annealing3 or by the application of a moving temperature gradient. Such techniques were mostly successful on wires, ribbons, or rods having small cross-sectional areas. Recently, larger samples of tungsten, molydbenum, tantalum, columbium, and rhenium were melted by a floating zone process which employed electron bombardment heating.10 Single crystals were obtained in many instances

Jan 1, 1959

By Arthur Taggart

FLOTATION of sulphide minerals and native metals is no longer a practical difficulty. The underlying scientific principles of the method, although not explored in anything like complete detail, have been formulated with sufficient breadth so that the direction of attack on any specific case is clearly indicated. It has been known since the earliest clays of flotation that certain of the nonsulphide nonmetal minerals-e.g., sulphur and graphite-would respond to flotation by oils as sulphides do; therefore they have been grouped with sulphides in many patents. But since the development of the chemical theory of collection,1,2,3 this similarity in action has been one of the facts cited in disproof of the theory by opponents of the hypothesis.4,5,6 Air levitation? of certain oxidized minerals, both metalliferous? and nonmetalliferous, and separa-tion thereby from other oxidized minerals, is a recent development in practice, although the discovery of the method dates back 17 years.7 This paper presents evidence that the principles underlying the air levita-tion of the nonsulphide nonmetal minerals are the same as those utilized in the flotation of the sulphides and native metals. It will be apparent immediately to anyone with knowledge of mineral concentration that separation of air-levitated minerals in water from minerals not so levitated is a simple matter of water-gravity concentra-tion, the separating device employed depending solely upon the size of the particles treated and the buoyancy differences effected by the levita-tion, The usual separating means employed are: (1) a flotation machine for fine, slimy and for well aerated granular material; (2) shaking tables for granular less aerated material.

Jan 1, 1937

CONTENTS PAGE ANDERSON, ROBERT J., and ENOS, GEORGE M.-Corrosion of Brass as Affected by Grain Size. Discussed by Henry S. Rawdon, Robert J. Anderson, Francis B. Coyle, William B. Price, and W. R. Webster 1 RAWDON, HENRYS., and MUTCHLER, WILLARD H.-Effect of Severe Cold Working on Scratch and Brinell Hardness. Discussed by W. H. Bassett, John Livermore Christie, John R. Freeman, Jr., W. R. Webster, William B. Price, Norman B. Pilling, D. J. McAdam, Jr., F. G. Smith, Zay Jeffries, F. E. Carter 3 WILLIAMS, ROBERT S., and HOMERBERG, VICTOR 0.-Relation of Heat Treatment to the Microstructure of 60-40 Brass. Discussed by 0. W. Ellis 14 Corrosion of Brass as Affected by Grain Size Discussion of the paper of ROBERT J. ANDERSON and GEORGE M. ENOS, presented at the New York Meeting, February, 1924, and issued as Paper No. 1282, with MINING AND METALLURGY, December, 1923. HENRY S. RAWDON,* Washington, D. C. (written discussion).-So numerous and so varied are the factors that affect the corrosion of metals that particular care is necessary in corrosion tests to eliminate so far as possible all extraneous factors. It appears to the writer that the question may well be asked as to whether all the necessary precautions have been observed in this investigation. It may be that the points to be mentioned were considered by the authors and found to be insignificant; however, there is nothing in the report to show this.

Jan 5, 1924

"Copper was first made in Butte by the use of iron for its precipitation from mine water in 1890. In consequence of a fire breaking out in the St. Lawrence mine of the Anaconda Copper Mining Company in November, 1889, a large quantity of water was poured into the workings, with the intention of flooding the mine and extinguishing the fire. This proved to be impracticable, but this water, on being pumped to the surface, was found to be high in copper sulphate,—tradition says 75/100 of 1 per cent. The Anaconda Copper Mining Company gave Wm. Ledford a lease on this water. He first (lug holes into the ground, filled them with scrap iron and allowed the water to flow through them. Later he built an open-top flume which he partially filled with iron and passed the water through the by the iron precipitation method. An assay in- the year 1890 from Gagnon mine water, showed .0016 per cent or 28 lbs. copper per day. The mine was then opened to the 1,000 level.None of the mine waters encountered in the solid rock in the mines of Butte contained copper in sufficient quantity to produce the metal profitably by the iron precipitation method. An assay in the year 1890 from Gagnon mine water, showed .0016 per cent or 28 lbs. copper per day. The mine was then opened to the 1,000 level."

Jan 1, 1913

By R. E. Reed, C. J. McHargue

Single crystals of aluminurn were reduced 90 pct in diameter by extrusion at 296" and 77°K. The resultant double fiber texture had a strong (111) component with a weak (001) component. The relative anzounts of these components varied with starting orientation. Decreasing the Lemperatuve of defovtnation increased the amount of (001) texture component in crystals with inilia1 orientations near (111). The starting orientation and temperature of deformation strongly affected the morphology of the (001) component. The effects of orientation and Lemperatuve upon the distribution of the (001 ) texture component in extruded aluminum single crystals were rationalized on the basis of deformation band formation and interaction. MANY papers since the early 1920s have discussed the occurrence of the double fiber texture (111) + (001) in wires and rods of deformed fcc metals. Aside from the reporting of experimental results for the various metals under a variety of fabrication conditions, emphasis has been placed on two related problems. One problem deals with the prediction of ideal end orientations based on the glide systems and flow directions. The other problem seeks the reason why different amounts of each component may be produced by the same fabrication schedule for metals apparently having the same deformation systems. Some of the difficulties in developing a satisfactory explanation have their origin in the experiments themselves. One mistake has often been the assumption of an initially randomly oriented specimen or complete ignorance of effects of starting orientation. Recent studies by Grewen and Wassermann,1 Cullity and co-workers,2' and McHargue4 have shown that the initial orientation may be the most important factor in determining the final orientation. Hence only limited comparisons of data from different studies can be made unless all conditions of the initial material are specified. Another question has been the nature of the (001) component. Hibbards suggested that any (001) present was the result of re crystallization during fabrication. Although Fleischer6 found no (001) texture in aluminum swaged at room temperature, and Dayal 7 found that component to disappear at very high reductions, a double fiber texture has usually been reported for aluminum. Vandermeer and McHargue showed that, while some (001) in aluminum may be the result of recrystallization, much of this component has its origin in the deformation process. Ahlborn and Wassermanng found the (001) component in silver deformed at low temperature not to be the product of recrystallization.

Jan 1, 1968

By Richard A. Busch, Roy L. Soderberg

Large, high, open stopes resulting from vertical crater retreat (VCR) and similar methods are usually filled with sand tailings to support the stope walls and make it possible to mine the pillars. The hydrostatic head resulting from these high stope fills demands extremely heavy bulkheads in the crosscuts to withstand the pres- sure. Occasionally, these bulkheads fail because there are no drains or the installed drains are inadequate. Costly flooding of the mine and loss of life result from these failures. With proper design of blanket drains and filters, the fill can be made failure-proof, requiring only a minimum bulkhead, designed specifically for zero water retention. The effectiveness of the blanket drains can be increased by laying perforated pipes on the bottom of the crosscut within the blanket drain. These drains can have a safety factor of 10 with minimal expense. When the water is properly drained, the hydrostatic pressure on the bulkhead is reduced to zero, leaving only the lateral pressure of the sand. This lateral pressure is partially dissipated by arching and shear against the crosscut walls and consolidation of the tailings as the water is drained. The bulkhead should be placed at least one cross-cut diameter back from the collar of the drawpoint.

Jan 1, 1983

The purposes of composition are various; one purpose, for instance, is to make a record for the writer's own use, as in a diary. That does not involve responsibility to others. There is also the writing meant to influence opinion-to be persuasive and pleasing. With such writing we need not concern ourselves at this stage of our study. The prime purpose of technical writing is to be informative-to convey information; therefore it must be clear beyond the chance of misunderstanding. Such clearness is impossible if meaningless or ill chosen words are sprinkled through the text. Discard the trivial phrases that are constantly at your elbow. Brush aside a host of vapid superlatives. Metternich exclaimed: "The superlative is the mark of fools". It is a false emphasis, like the underlining in a school-girl's letter. For example, the little word 'very' can be deleted nine times out of ten; it is an impediment to terse and perspicuous writing, as the multitudinous hand-baggage of the British tourist is to his travel. 'Very' supposes comparison. A mine with a 1000-ft. shaft is very deep to the scribe who writes from the Joplin district, in Missouri, but it seems a shallow hole to a man living at Calumet, Michigan. A vein that is 10 feet across may be considered very wide at Cripple Creek, Colorado, but it is only a 'stringer' to the miner at the Homestake, in South Dakota. Ore assaying $20 in gold is very rich at Juneau, Alaska, where 10,000 tons of $1 ore is crushed daily, but it is relatively low-grade to the pocket-miner at Alleghany, in California. It is all a matter of comparison; unless the reader knows your standards of depth, width, or richness, your 'very' has no significance. "Where erosion was very rapid or oxidation very shallow"

Jan 1, 1931

By B. C. Blake

IN general, billet-type or long slender ingots are used when it is desired to produce directly from the ingot in one conversion a product of medium or small cross-sectional area. They are designed to eliminate the blooming and billet-mill stages of the usual procedure. As used at Connors, they constitute a means of keeping a continuous rolling mill busy in the production of high-quality small rods, small angles, hoop stock, baling ties and concrete reinforcing rods without the need for a blooming or billet mill. They represent sound steel with the best surface that is commercially practical to use in the rolling of small continuous mill products.

Jan 1, 1947

By Paul H. Lu

Methods and results of measuring three basic parameters for ground stability control, ground pressure, strata movement, and geomechanical properties of mine rock are presented in this paper. It is found that these parameters can be measured in situ by simple and practical techniques with nonsophisticated and inexpensive instruments. Specifically, a drillhole dilation technique employing a cylindrical hydraulic borehole pressure cell (CPC) was used to determine the modulus of rigidity. Premining ground pressures were determined by pressure convergence tests with a combination of one CPC and two pre-encapsulated flat hydraulic borehole pressure cells (BPC) installed in a single drillhole. Abutment pressures and pillar loading were monitored with BPC's. Differential strata movements and bed separations were measured with self-recording 10-anchor-point extensometers. Roof-to-floor convergence was measured with self-recording convergence meters. Some applications of these in-situ-determined parameters to mine design and ground stability control are also discussed.

Jan 1, 1984

By Nick Warren

The problem considered is that of predicting rock physical properties from observations of the structure of the rock. The approach here departs from previous studies in that both the physical properties and structural features are taken as statistical data and the relations between them are cast as statistical functions. This approach I have termed a "quantitative petrostructure analysis". This Paper deals with two aspects of making such a study; parameterizing patterns of topographic features of rock, and characterizing variables to allow correlation studies to be carried out. The principle of a quantitative petrostructure analysis is outlined and illustrated using maps from two samples of Conway granite.

Jan 1, 1982

By M. C. Van Camp, J. D. Miller

Preliminary results are reported regarding the design and development of a pilot scale air sparged hydrocyclone for cleaning fine coal 590 pm (- 28 mesh) containing 24% ash and 1.6% sulfur. The principle of separation is the flotation of hydrophobic coal particles in the centnjugal field generated by the fluid flow in the air sparged hydrocyclone as discussed in another publication. This 152-mm (6-in.) hydrocyclone has a nominal capacity of 0.9 t/h (1 tph) and experimental results suggest that separations vastly superior to a water-only cyclone are possible. In addition the separation efficiency is as good, if not better, than that achieved with conventional flotation cells. For example, typical results indicate that 75% clean coal can be recovered at 15% ash leaving a tailing product of almost 50% ash. These experimental results coupled with the high capacity of the air sparged hydrocyclone (imagine a retention time for flotation of only two seconds compared to two minutes for conventional flotation) may represent a significant breakthrough, not only in coal preparation technology, but in the flotation of fine particles in general.

Jan 1, 1983

By Jill Dill Pasteris

Several mineralogical prospecting techniques are used in diamond exploration. Most are concerned with identifying indicator minerals such as pyrope garnet and magnesian ilmenite, which are derived from mantle xenoliths hosted by kimberlites. The first goal of such prospecting is to locate kimberlite intrusions; the second goal is to identify the diamond-bearing kimberlites. Explorationists have worked much less on the indigenous kimberlite phases. The kimberlitic opaque oxides, ilmenite and particularly spinels, promise to be useful in discriminating between intrusion episodes in identified kimberlites, and perhaps in the evaluation and prediction of diamond grades. Several petrologists have showed that spinel compositions and zoning patterns are specific to certain intrusive facies in South African and Canadian kimberlites. Careful evaluation may indicate a correlation between spinel parameters and diamond content.

Jan 1, 1984

By W. A. Backofen, B. C. Wonsiewicz

The Plasticity transition in magnesium was studied by plane-strain compression of single crystals and polycrystalline material at temperatures from about 20" to 307°C. Reduction of single crystals along the c axis was accommodated by twinning on {1011) and retwinning on (10 12}, followed by basal shear in the doubly twinned volume. Deformation in that mode can result in sufficient independent shears for arbitrary shape change. Fracture in c axis compression, below about 100°C, has been related to excessive shear caused by unloading from the stress for {1011} twinning (-50 ksi at 20°C) to that for slip within the twin (-3 ksi); ductility follows from heating because the stress difference is lowered and the twin volume, in which elastic strain energy is dissipated on unloading, is increased. The stress for (1011) twinning is strongly temperature-dependent but not given by a critical resolved shear stress law. The latter is attributed to the influence of stress concentration from prior intersecting shear on nonbasal planes, the former to the temperature dependence of the preliminary slip. THE basic symmetry of hcp crystals has the effect of limiting the number of independent slip systems and making twinning an important deformation mechanism. The general result in wrought polycrystalline aggregates is a more or less sharply developed texture (or preferred orientation) which underlies a strong anisotropy in mechanical behavior. Knowing how the one influences the other is essential background for the use of such materials. Magnesium was of interest in this work because of the unexplained plasticity transition that it undergoes somewhere in the neighborhood of 200°c.''~ At lower temperatures plastic deformation before fracture in polycrystalline material is limited, while at higher temperatures extensive deformation is possible. The transition temperature commonly determines the lower limit of the range in which magnesium is worked. The limited ductility can be traced to a lack of independent crystallographic shears. A minimum of five are required for arbitrary shape change.' Around room temperature, however, slip on all known systems provides only four.' In each case, the slip direction is in the (0001) basal plane so that slip does not allow strain along the c axis. With increasing temperature, more slip occurs on the ( 1011) pyramidal plane and the ( 1010) prism plane but without change in direction.'?' Thus, that development alone cannot explain the transition temperature.

Jan 1, 1968

By Alan Morris

IN a previous paper1 the results of cutting tests on free-cutting brass rod were reported. Investigation was made of the effects of variation in lead content, microstructure and cold drawing. The author's reply to the discussion of that paper includes a study of the directional cutting properties of drawn and annealed rod. The present paper records the results of tests made on series of samples in which the tin, iron and copper contents have been varied. The apparatus, used and method of testing are described in detail in the previous paper. The machine is of the pendulum-operated milling type used and described by Airey and Oxford.2 Angular readings of the height to which the pendulum rises after falling from a fixed position, both when a cut is made and when the pendulum swings freely, give the basis for calculation of the energy consumed in making a cut. Careful weighing of the sample before and after cutting gives a measure of the amount of metal removed. The results are expressed in foot-pounds per cubic inch of metal removed, and have been called "unit cutting energy." In the course of the discussion of the author's earlier paper, W. B. Price reported large-scale tests involving some 50,000 lb. of material. These tests indicated that the addition of as much as 0.6 per cent of iron and 0.25 per cent of tin had apparently no adverse effect on the high-speed cutting characteristics of the rod. The rod also contained a small amount of nickel. The test results reported here tend to confirm his observations.

Jan 1, 1933

By O. B. Hopkins

The reports for the years 1942 and 1943 were written in 1943 and 1944, respectively, and were summarized at the meetings of the Institute in February 1941 and February 1944, but were held in manuscript form until released for publication in 1945. 1942 During the year 1942, developments in the Peruvian oil industry continued to be subject to repercussions from the swelling war effort, which steadily diverted more of the normal supply of men and materials into war channels, and necessitated the rerouting of supply lines. The result in Peru was an increasing demand for crude oil and products. The production of petroleum in Peru in 1942 was 13,626,259 bbl., as compared with 11,935,584 bbl. in 1941—an increase of 1,690,675 bbl., or approximately 14 per cent. The largest increase, amounting to over 61 per cent, was from the Lobitos fields, but this increase was caused largely by the subnormal production in 1941. International Petroleum Company's production in the La Brea y Parinas field increased 727,111 bbl., or 7 per cent, whereas the Peruvian Government's production in the small Zorritos field declined 10,380 bbl., or approximately 20 per cent. The final production figures for the Ganso Azul field at Agua Caliente were not available for 1942 at the end of the year, but the production was believed to have increased approximately 80 per cent from 1941, or from 13,750 to approximately 25,000 barrels. Development and Exploration Exploration in Peru in 1942 was very limited and confined to areas adjacent to the older producing fields, and the efforts there were largely expended in the extension and development of the producing areas. This situation resulted partly from the shortage of transportation and drilling equipment, and also from the strong demand for increased production of oil. . International Petroleum Co. completed 69 wells during the year, including seven exploratory wells, three of which added moderate extensions to the proven areas. Sixty of the completions were oil wells and nine were dry holes. Lobitos Oilfields, at Lobitos and Restin, is understood to have concentrated its drilling effort on development rather than on exploration. The Peruvian Government operating at Zorritos confined its drilling to the development of the small producing areas previously found. During the year it announced plans to drill three exploratory wells in the Pirin area of southern Peru (see map on p. 638). It was reported that the Government had made a survey of the Sechura area (representing the southern part of the Northern National Reserve as shown on the map), but no work under this arrangement was announced. The Cia. Ganso Azul, at Agua Caliente, completed its No. 6 well as a producer on March 27, and during the year it completed the installation of a 400-bbl. topping plant.

Jan 1, 1945

New Products Equipment

Jan 3, 1951

By Christopher Haycocks, J. Richard Lucas

The growth of computer and ground control technology in recent years, combined with an urgent demand for low-cost fossil fuels and mineral resources, has set the stage for full-scale utilization of computers in mine planning. Steeply rising production costs and the need to preserve the environment are placing great demands on engineers to improve their mining efficiencies, which can best be accomplished by applying the full capabilities of the computer. Pressure to develop and perfect programs with an immediate potential for improving mine design, reducing mining costs and extending the viable coal reserves of the country has already come to bear in the form of exploding energy requirements, environmental considerations and the visible limitations of other energy sources.

Jan 4, 1973

THE great subject of interest in American affairs during February was the consideration of the proposed soldier bonus. This proposal was based upon the idea that, because most of the workers of the United States had enjoyed high wages during war, the soldiers were entitled to "adjusted compensa-tion" in order to equalize things. It overlooked the fact that the soldiers, themselves, had the opportunity to enjoy high wages in 1919 and 1920, when rates were highest. Apart from this, the whole project was founded on fallacies and involved what would be nothing less than economic crime. Although it looked as if the measure were destined to be railroaded through Congress, so great a storm of protest was pelted upon Congress that the present outlook is that the whole project will be abandoned. There was probably some increase in the physical volume of business during February. A rise in prices for agricultural products assisted the farmers mate-rially. These developments, however, are not to be construed as presaging any general upward movement. On the contrary, the current year is to be contem-plated as one of serious labor troubles, following inevit-able reductions of wages. These began in February in the form of an extensive strike in the cotton textile industry of New England, accompanied by some rioting in Rhode Island. The coal miners have had numerous conferences, without coming to any encouraging results, and the stage appears to be fully set for a general strike beginning Apr. 1. About the only question now is whether this will comprise both the bituminous and anthracite miners. If the latter refuse to go out, no serious shortage of coal is anticipated, the belief being that the existing stocks together with the output of the non-union mines will supply the demand, which is sub-normal even now. In the metal industries, lead and zinc were dull but stable. The weakening tendency in iron and steel that was manifest during January appeared to be checked, at least temporarily. Copper was charac-terized by a distinct weakness and a considerable decline in the market. This downward movement was inspired by the news during January that several of the important mining companies were taking steps to resume production. During February the demand for copper, both foreign and domestic, was poor.

Jan 3, 1922