Search Documents

By A. M. Nicholas

WHEN attempting to lift mill pulp containing a considerable percentage of wolframite, in an ordinary bucket elevator, difficulty was encountered from the tendency of the tungsten minerals to settle, on account of their high specific gravity. Lifts not exceeding 20 ft. (6m.) could be accomplished without particular difficulty, because there was insufficient time for consolidation of the heavy minerals in the bottom of the bucket; but with higher lifts, the heavy tungsten minerals would settle so solidly that when the bucket turned over at the top of the elevator the contents could be only partially dumped. In this case it ,was necessary to lift the material a distance of 34 ft. (10m.); hence some means had to be adopted to prevent settling, at least to such an extent that the material could be dumped from the buckets. To reduce the carrying time to a sufficient extent would have required a belt speed of 475 ft. (144.7m.) per minute, which was not feasible. It was decided to try, by vibrating the belt about midway of its span, to keel) the material sufficiently agitated during elevation to prevent settling. Underneath the rising side of the belt was placed a 12-in. (30.48-cm.) idler pulley, 18 ft.-(5.5 in.) up in the total lift of 34 ft. The idler pulley was set eccentric by 3/4 in. (19 mm.) and it was hoped that the vibration thus imparted to the belt, running at a speed of 280 ft. (85 m.) per minute, would prevent settling in the buckets. It was found that the pressure of the belt on the idler, due to the small inclination of the elevator, was not sufficient to overcome sliding on the idler, and the agitation was insufficient to accomplish the desired purpose. The idler was then connected to the drive shaft of the elevator through an intermediate pulley, gearing down to a speed of 20 r.p.m., so that a positive vibration was imparted to the belt; this imparted enough motion to the belt to prevent settling and the contents of buckets clumped satisfactorily.

Jan 2, 1918

By Keith Sutherland

AEROFLOAT 25 is a complex mixture of free cresylic acid with aryl substituted dithiophosphoric acids, sulphides, disulphides, etc. Its complete composition has not been published by the makers or patentees. It is prepared1 by the reaction between phosphorus pentasulphide and carefully selected cresylic acid. We have been informed that this acid contains no phenol and very little cresol, and that it is rich in the higher alkyl phenols, particularly the xylenols. The reaction between a phenol ROH and phosphorus pentasulphide may produce compounds of the following type:2 (i) RO S P Diaryldithiophosphoric acids RO SH (ii) R-SH Thiophenolic compounds (iii) R-S-R Diaryl sulphides (iv) R-S-S-R Diaryl disulphides (v) Substituted thianthren compounds Except for the simplest type, the thiophenols (ii), the boiling points of these compounds lie above 300° C. The amounts of the thianthren compounds formed from the five xylenols (if all these are present) will vary according to the position of the substituents. In an attempt to ascertain something of the nature of the reagent, fractional distillation under atmospheric pressure was undertaken. At the outset, hydrogen sulphide was freely evolved, and-particularly below 200° C.-the fractions had the strong odor characteristic of the

Jan 1, 1939

By R. A. Perry

A speiss is an artificial arsenide, sometimes an antimonide, formed in lead smelting, smelting of oxide copper ores, and in some lead-refining operations. The production of speiss is closely allied with the amount of arsenic and metallic iron in the blast-furnace charge, while dross is produced mostly from the copper and sulphur, with varying amounts of antimony, arsenic and nickel. Most speiss is essentially an iron arsenide containing some sulphur, copper and nickel, if these elements are present in the furnace. The recent introduction of the soda treatment of lead drosses has produced a speiss high in copper. Speiss is not miscible to any extent with molten copper, lead, matte or slag. Miscibility increases with temperature. This property of the speiss is clarified in the latter part of this paper. Most speisses are produced in conjunction with matte and their sulphur content points to the solubility of matte in speiss. . Some plants have insufficient speiss to warrant separate treatment. When arsenic is high in the blast-furllace charge, there may be sufficient speiss to tap separately from the first settler. Arsenic From the foregoing, it is obvious that a study of the treatment of speiss would not ,be complete without consideration of arsenic. Inasmuch as perhaps go per cent of the blast-furnace feed may be sinter, a definite knowledge of the properties of arsenical ores and compounds that go in to the roaster and sinter feeds is of value. Lcad smelters obtain their arsenic from ores and concentrates, as well as from flue dusts shipped from other plants, particularly copper smelters. The percentage of arsenic in ores is usually low, although occasional lots of high arsenical products are smelted. These crude ores may be sulphides, as arsenopyrite; or oxides like scoiodite, which carry gold or lead minerals. The small amount of arsenic in the original ores received is greatly increased by a circulating load of arsenic in secondary products at are resmelted for their lead or precious metals. More important than the arsenic present directly in the concentrates treated is that in fumes and dusts that may originate in the blast furnace or sinter plant of the lead smelter, or may come from a copper smelter as lead-bearing converter fume or roaster dust. Thus the lead smelter not only must treat its own arsenic but is compelled to handie that from some copper and perhaps other lead plants. Where copper and lead plants exchange products, each plant may be forced to re-treat part of the arsenic it has shipped ,outside its own confines. Speiss from the lead blast furnace contains chiefly iron and arsenic with some lead, copper and sulphur and often appreciable amounts of gold and silver. If its copper content is sufficient this speiss may be sent to the copper smelter where usually it is treated in the converter and the copper is separated as blister. Much of the arsenic and most of the lead are recovered as converter fumes

Jan 1, 1944

By David W. Brunton

The list of our past-Presidents comprises the names of many who, in their official addresses, have sketched the current progress of the arts and professions with which they were familiar. Such addresses are, in my judgment, highly useful, setting forth the results of our own work as a society, and recalling to our minds the particular lines in which discussion would prove most fruitful. Following this course with some hesitation, I venture to offer an outline of the recent improvements and the present situation in mining and metallurgy in the Western United States. The wonderful advances in mechanics, chemistry, and electricity have all combined to aid these arts to such an extent that progress during the last decade has undeniably been more rapid than ever before in the history of the profession. In all mining countries improved transportation-facilities, in many instances called into existence by the traffic created by the mines themselves, have done much to enlarge the field of operations by the reduction of freight-, operating- and living-expenses, thereby bringing lower-grade properties into the producing class. Under normal conditions, as the age of a district increases, all these different factors should combine to off-set the augmented costs attendant on deep mining, and greatly tend to prolong the profitable life of the mines. The more recent and important improvements in our Western mining-practice which have contributed most towards the advancement of the art may be briefly summarized as follows; but, before beginning this portion of my address, I wish to thank most heartily the many engineering friends who have so

Jan 1, 1910

By T. E. Leontis, R. S. Busk

WORK was initiated several years ago at The Dow Chemical Company to determine the applicability of powder metallurgy processes to magnesium and its alloys. Although it was found possible to apply the normal techniques of compacting and sintering, it was discovered early that the technique of extrusion offered special promise. This technique and the alloys produced were therefore studied extensively, and the present paper is a partial report of those studies. It is expected that a second paper will discuss more extensively some of the alloy systems simply mentioned here. Although the literature on powder metallurgy is very extensive, there are only two articles dealing with magnesium13,14 and there is no reference to the direct extrusion of the powder of any metal without the preliminary step of compacting. Furthermore, no mention has been made of the possibility of designing alloys by the technique of powder extrusion, particularly alloys that cannot be made in any other way. Sauerwaldl3 discusses the extrusion of magnesium and aluminum powder to produce alloys containing nonequilibrium phases, but again he emphasizes the importance of pre-compacting before extrusion. There seems to be general agreement that some form of hot-pressing is essential to obtain in a compact the full theoretical density of the metal used.'-" The nearest approach to the technique of direct powder extrusion is that of extrusion of pre-sintered compacts,'-" for which the best review through 1944 is that by Kieffer and Hotop.11 Ensign* discussed a specialized technique of "extruding" already compacted and sintered gears for the purpose of sizing. Sauerwa1d13 discussed the compacting and extrusion of magnesium and magnesium-aluminum alloy band-saw chips. The properties of the extruded compacts were found to be comparable with those of extrusions prepared from solid billets. He also extruded a compacted mixture of magnesium and aluminum powder and found the properties to be somewhat different from those obtained on an extrusion made from a cast billet of the same composition. The second reference dealing specifically with the powder metallurgy of magnesium is Stern's patent," in which is described the extrusion of scrap chips and turnings following a hot-pressing and sintering step. Considerable emphasis in most of these articles is placed on the necessity of atmospheric protection to minimize the danger of oxidation. Experimental Procedure The first experiments were made with the small extrusion press shown in fig. 1. With this press, billets of about 1/2 in. diam are used to produce wire

Jan 1, 1951

By R. Thiessen

The question whether the kind, rank and grade of coal is in any way determined by the kind or type of plant from which it originated has been a problem since coal was first studied. Some investigators claim that the kind of plants has contributed none of the attributes that characterize the differences found in the various coals; others claim that all differences are caused by the contributing plant; and others hold that only a few characteristics are inherited from the kind of plant from which the coal originated. Most coalologists, however, give this matter no thought. It can easily be shown that the kind of plant which contributed to a coal had a marked influence on its kind and type. A number of factors enter into this problem, and all unrelated ones must be carefully eliminated, including metamorphism caused by the pressure of the cover, earth movements, mountain building and higher temperature. Only the fundamental substance—the plants out of which coal was formed—• and the causative conditions that gave rise to a peat swamp and the conditions imposed upon the plant and the plant substances during the formation of the peat swamp can be considered. Everything else being equal, the question then is, how far do different classes and types of coal owe their differences to different kinds or types of plants? Geologic Age of Coal Coal has been laid down in almost every geological period since the Devonian era. Even as early as the middle Devonian some coal was formed; although of no value it has great scientific significance. The most valuable coal was deposited during the Carboniferous. The coals of England were formed during the Mississippian, and most of the valuable coals of America, Europe and China during the Mississippian and chiefly the Pennsylvanian. From the Permian come the coals of France, Saxony, Thuringia and Schwarzwald in Germany and of Bohemia and of the Ural districts of Russia. From the Mesozoic come the coals

Jan 1, 1930

By M. MacFarland, E. McAuliffe

Our North American railway system, including the lines serving the United States, Canada and Mexico, with a total operating mileage of 303,040, employing 71,818 locomotives, represents not only the greatest industrial user of fuel coal, but in the variety of coals used, ranging from anthracite down through the several gradations of bitumirlous coals, as well as lignites, covers about all there is in American-mined coals. Necessarily the wide range of fuel coal embraces not only extremes of calorific value but also every possible gradation shown in size and preparation, from run of mine to washed nut and slack. Approximately 8 per cent. of the fuel used by the railroads is consumed in shop power plants, shop buildings, pumping stations, station buildings, etc. The principal class of coal (as designated) used by the railroads is bituminous, such, however, including a substantial tonnage of subbituminous and lignite coal; all United States railroads using in 1923 for locomotive, shop, station buildings and miscellaneous uses, a total of 4,578,000 tons of anthracite, 155,795,000 tons of bituminous, subbituminous and lignite coal and 58,005,000 bbl. (42 gal.) of fuel oil. The Class 1 railroads of the United States (those whose gross annual earnings equal or exceed $1,000,000) used in 1926: Bituminous, subbituminous and lignite coal, net tons..... 140,083,885 Anthracite, net tons................................ 3,667,505 Fuel oil, gal........................................ 3,058,915,511 Railroad fuel-purchasing agents rarely attempt to classify coal for locomotive use on the basis of chemical analysis; although this is very generally used as a guide in the initial selection of a fuel supply. The extraordinarily high rate of combustion developed in the modern locomotive, generating as high as 2500 b.hp., with limited facilities for cleaning fires en route, suggests the importance of a fuel supply containing a reasonably low percentage of ash-making material, and while the percentage of locomotive coal handled through automatic stokers is growing, the principal tonnage is yet fired by hand.

Jan 1, 1930

Jan 1, 1918

By H. Shaw

It is now generally recognized that the gravitational method of geophysical surveying is a valuable aid in elucidating the geological structure of the subsoil and enables the practical geologist to deduce the presence of useful deposits. The particular suitability of the torsion balance to the location of large and important subterranean structures has given rise to a wide application of this method by many of the important oil companies in their search for future supplies, and so intense have been these efforts that little has been heard of the method in other connections, with the exception of occasional references to its application in the location of hidden deposits of metallic ores, salt and lignite, and a number of accounts of its use in the elucidation of geological structures. Its success in the location of salt domes is well known, and establishes it as one of the most important of the geophysical methods, especially for the indirect location of oil. In the British Isles, however, no large occurrence of oil is likely to be revealed, and here the practical application of the gravitational method has been restricted almost entirely to the search for ores. This type of survey possesses well marked characteristics, and presents a gravitational problem that has necessitated the development of a special and probably unusual plan of campaign, full details of which it is hoped will shortly be published. The problems and difficulties encountered in this work are of necessity fundamentally related to those met with in the search for oil by means of the torsion balance, but they also possess several special and distinctive features which undoubtedly differentiate them from the obstacles confronting the oil prospector, and which call for special consideration and treatment. In certain of the various oil-producing areas of the world, and particularly in the Gulf Coast region, the geology may be regarded as comparatively simple, while the oil is usually associated with a large and well defined structure such as a salt dome or anticline, which is capable of giving gravitational indications sufficiently extensive to be detected by the torsion balance over a fairly wide area of the ground surface. It is customary, therefore, during the preliminary survey of an area for oil, to

Jan 1, 1929

By S. T. Wlodek

The surface and subscale oxidation reactions were followed by means of continuous weight-gain and metallographic techniques over the range 1600" to 2200°F (871° to 1204 °C) for up to 400 hr. Full identification of all scale and subscale reaction products was obtained by electron and X-ray diffraction. At or below 1800°F (982°C) a linear rate of reaction (QL = 46.0 kcal per mole) governed the oxidation process, extending for up to 100 hr at 1600°F (871 "C). During linear oxidation the surface scale consisted of an amorphous SiO2 film overgrown with Cr 2O 3 and NiCr204. This initial linear process was followed, and above 1800°F completely replaced, by two successive parabolic rate laws (Qp = 60 and 57 kcal per mole). This parabolic reaction involved the formation of a complex scale consisting of Cr2 O3 and smaller amounts of NiCr2O4. Parabolic oxidation appeared to coincide with the disruplion of the silica film present during linear oxidation and was followed by subscale (internal) oxidation of crystobalite and NiCr2O4. The balance between the subscale and surface oxidation reactions controls the oxidation of this commercial alloy. The amorphous silica film appears to result in the linear rate and diffusion through Cr2O3 is the more likely rate-limiting step during parabolic oxidation. THE oxidation of a multicomponent composition is a complex phenomenon not presently amenable to a rigorous classical interpretation. Nevertheless, even a qualitative understanding of the scaling and subscale reactions that occur in a commercial composition can illuminate the reactions that limit its high-temperature stability in an oxidizing environment. This study of the oxidation of Hastelloy Alloy X presents the first of a series of studies with the above approach in mind. Hastelloy X exhibits one of the best combinations of strength and oxidation resistance available in a wrought, solution-strengthened, nickel-base alloy. Although during long time exposure some precipitation of M6C and M23C8 carbides as well as a complex Laves phase occurs, the amounts are probably small enough to have no appreciable effect on the chemistry of the matrix. Radavich has identified the oxidation products on Hastelloy X oxidized for 5 min to 10 hr at 1115°F as NiO and the NiCr2O4 spinel. Oxidation for 5 to 15 min at 1500°F produced a scale of spinel, NiO, and a rhombohedra1 phase, probably Cr2Os. Sannier et 2. have reported continuous weight-gain data for Hastelloy X at 1650" and 2010°F and internal-oxidation measurements after 150 hr at 2010°F. In addition, much of the data on binary Ni-Cr alloys recently reviewed by Kubaschewski and okins' and Ignatov and Shamgunova4 as well as studies of binary Ni-Mo alloys5 are also pertinent to the oxidation of this composition. EXPERIMENTAL Continuous weight-gain measurements and metallographic measurements of subscale reactions were the main experimental techniques used in this study. X-ray and electron diffraction backed up by a limited amount of electron-microprobe analysis served to characterize the nature of the scale- and subscale-reaction products. Two heats of commercial sheet of the composition given in Table I and identified as A and B were used in the bulk of this study. Internal-oxidation measurements were made on a third heat of material in the form of a 0.5-in.-diam bar. In order to assure homogeneity, all heats were reannealed 4 hr at 2175°F prior to sample preparation. weight-Gain Measurement. All specimens (1.5 by 0.4 by 0.03 in.) were abraded through 600 paper, electropolished, and lightly etched in an alcohol-10 pct HCl solution. An electrolyte of 150 cu cm H,O, 500 cu cm HsPO4 (85 pct conc), and 3 g CrO3 at a current density of 0.9 amp per sq cm or a solution of 10 pct HaW4 in alcohol used at 4 v and 0.3 amp per sq cm was used for electropolishing. The resultant surface exhibited a finish of 3 ± 1 p rms. Continuous weight-gain tests were made at 1600°, 1700°, 1800°, 1900°, 2000", and 2200°F on auer' type balances capable of recording a total weight change of 110 mg with an accuracy of k0.1 mg. All tests were made in air dried to a dew point of -70°F and metered into the 2-in.-diam reaction

Jan 1, 1964

By Charles W. Goodale

The ores of the Butte district present a variety of combinations, and their treatment by concentration is an interesting study. They may be classified in general as follows: 1. Copper-silver ores, which are produced by the mines of the Anaconda group, and by the Mountain View, Colusa, Silver Bow and Parrot. The high-grade ores from these properties are roasted and then smelted; but a large proportion of the output is low-grade and siliceous, and hence requires concentration. The copper-bearing minerals are chalcocite, bornite, enargite and chalcopyrite, in varying proportions in the different mines, the gangue, which breaks readily into grains, being quartz and feldspar. 2. Silver-copper ores, of which the Gagnon vein is the largest producer. The grade of the ores from this mine is such that nine-tenths of the output requires concentration. The silver- and copper-bearing minerals of this vein are massive wurtzite, sphalerite, bornite, chalcopyrite, pyrite, tetrahedrite, enargite, tennantite and galenite, with a quartz gangue associated with feldspar and small quantities of barite and fluorite. The gangue is very hard and not at all granular. 3. Silver-ores containing a small amount of gold, embracing the product of the Alice, Magna Charta and Moulton claims, on what is known as the Rainbow lode, and that of the Lexington, Blue Bird, Nettie, Burlington and other mines. The gangue is quartz, carrying pyrite, sphalerite, galenite, tetrahedrite and argentite, with manganese in the form of rhodochrosite and rhodonite. Good results on ores of this class cannot be obtained by concentration, because large percentages of the silver-bearing minerals are disseminated through the gangue in such minute grains that even the finest practicable crushing

Jan 1, 1897

By Clarence Zener

THEORETICAL considerations by one of the authors have led1 to the prediction that the dynamic internal friction of annealed metals has a broad maximum at a certain grain size. This prediction they have veri-fied2 for alpha brass. In the present paper the theory is extended to include the precise manner in which the internal friction varies with grain size on either side of the maximum. New experimental data are pre¬sented to test this extended theory. The physical basis for the type of internal friction that is being investi-gated lies in the interplay between stress and temperature. Just as local fluctuations in temperature give rise to local fluctuations in stress, so like-wise fluctuations in stress give rise to fluctuations in temperature. But temperature gradients give rise to necessarily irreversible thermal cur-rents, and hence to internal friction. The theory for this type of internal friction has been developed quantitatively,3 and has been experimentally verified,4,5 for the particularly simple case of the transverse thermal cur-rents accompanying transverse vibrations. Of more fundamental impor-tance are the intercrystalline thermal currents accompanying all types of vibration. The variation in stress across grain boundaries arises from the elastic anisotropy and at least partial random orientation of the individual crystallites. An exact quantitative treatment of the internal friction due to these thermal currents is of course out of the question. However, much information can be obtained from general arguments.1,6 Thus when the frequency of vibration f is low, or when the grain size d is small, adja-cent grains remain nearly in thermal equilibrium, and vibration proceeds isothermally with little internal friction. Again, when the frequency is high, or the grain size large, the heat flow per cycle is small, the vibration proceeds adiabatically with little internal friction. The internal friction will become a maximum in the transition region. The degree of adiabatic-

Jan 1, 1940

Jan 1, 1968

By C. Augustus Carlow

THE subject which has been allotted to me is so vast and far-reaching that it is impossible to deal adequately with it in the time available. A complete survey would occupy the spare time of any one man for many years, whereas the time available to me is measured in weeks In the circumstances, I have been fortunate in securing the aid of several willing collaborators, and shall endeavor to re present such information as presently exists in published form, examine the situation critically in the light of present-day conditions, and arrive at certain conclusions' which I shall venture to put forward for your consideration No one who has lived through the past 25 or 30 years, and who has witnessed the amazing achievements of recent scientific research, would venture to deny the possibility that new sources of energy-may yet become available, or to prophesy to what extent these may be harnessed to the service of mankind So far as we can see, however, coal, as a source not only of power and heat but also of that wonderful range of derivatives that form the raw materials of so many industrial processes, must continue to play a vital role in our economic life It is the chief mineral fuel, exceeding all other mineral resources in value, production and demand In value coal overshadows the industrial metals, while of the sources of energy-coal, oil, gas and water power-the first named is the most important Thus, for example, in the United States, coal as a fuel (that is, as a source of heat and power) is still predominant, the figures of percentage of

Jan 1, 1947

By Samuel Shallcross

THE principal function of the Bell limestone mine, of the American Lime & Stone Co., at Bellefonte, Pa., is to supply raw material to the company's modern rotary kiln plant at Bellefonte. Because mining costs are naturally higher than many open quarries with more favorably lying strata, it cannot compete, except to a limited extent, in the markets for road material and fluxing stone. In the broad sense, mining does have an advantage over the average open quarry when the end products are designed for and controlled by process and final inspection for the exacting demands of the industrial and chemical markets. Approximately 80 per cent of the output of the Bell mine is sold in the industrial and chemical markets. And as higher standards are set each year for construction and agricultural work, the remainder of the mine output goes to these two classes. Mining produces more fines than open quarries, and these fines are difficult to market; on the other hand, owing to absence of contaminating clay and impure rock, a greater percentage of the output of a mine is marketable. Because of the great production of fines, rotary kilns for lime burning are necessary when the stone must be mined. In 1921 the American Lime & Stone Co. operated 19 quarries and 72 lime shaft kilns spread over an area of 40 miles between Bellefonte and Altoona, Pa. At that time the line-production capacity of the 72 kilns amounted to approximately 700 tons per day. After 15 years the company operates three rotary kilns and six shaft kilns, with a combined output of approximately 500 tons of lime per day, concentrated in its single Bellefonte plant (Fig. 1). Its only stone-producing plants are now the limestone mine at Bellefonte and a construction-stone open quarry at Union Furnace, near Tyrone, Pennsylvania.

Jan 1, 1936

By A. Sutulov

The segregation process, an alternative to benefi-ciation of oxidized and mixed sulfide-oxide copper ores, is studied here with particular emphasis placed on time, temperature, and coke and salt percentage factors. The results show that in a segregated charge, the copper assay of the coarsest fractions normally is of the same order as the copper assay of the tails obtained from grinding and flotation of the same charge. This observation suggests the possibility of limiting or even eliminating the grinding step from the flowsheet of a segregation plant. The segregation process, which offers an alternative to beneficiation of oxidized and mixed sulfide-oxide copper ores, was discovered in 1923 by Moulden and Taplin1,2 who were attempting to apply the Perkins process3'4 to a Chilean ore from the Sagasca mine. After a number of investigations and pilot plant tests,'-' the segregation process became a successful industrial operation.'r9 The process aroused considerable interest in Chile because of the existance of large reserves of oxidized copper minerals which could not be treated by conventional hydrometallurgical methods because of the high consumption and prohibitive cost of sulfuric acid. During the last two years, the Mineral Dressing Dept. of the Institute de Investigaciones Tecnology cas of University of concepci6n (Chile) has carried out a test program on 23 different ore samples representative of the national territory. These tests were carried out on a semi-continuous and batch scale with a rotary, automatically controlled and gas-fired furnace (supplied by Bartlett and Snow, Fig. 1). The results of these tests indicate that out of the 23 samples 20 can be successfully treated by this process with recoveries of copper ranging from 85 to 95%.10,11 The purpose of this paper is to treat some specific problems related to the segregation process. TIME AND TEMPERATURE FACTORS Time and temperature of calcination play an important role in the segregation process. When moderate salt and coke conditions were maintained (each of reagents was added in the quantity of 1 — % wt), systematic testing easily demonstrated the influence of these two factors on segregation and flotation recovery. The pertinent results are summarized in Fig. 2. To determine what specific changes the segregation process made on the ore, the samples, segregated at 700°C for different periods of time and under standard conditions, were granulometrically analysed and

Jan 1, 1963

By N. J. Grant, C. F. Flo, F. B. Cuff

An investigation of the Ti-Cr system has shown the presence of a complete series of solid solutions in the ß phase, with a minimum in the solid us near 50 pct Cr. An intermetallic compound, TiCr2, forms during cooling from the ß solid solution. There is a eutectoid reaction at the low chromium side of the system. IN view of the recognition of the potentialities of titanium and its alloys as important structural materials there has arisen a need for a systematic investigation of various titanium binary diagrams. Of these, the Ti-Cr system was of particular interest because of the improved properties imparted to titanium by small chromium additions. A literature survey disclosed a partial constitution diagram that had been suggested by Vogel and Wenderott,¹ This diagram, shown in Fig. 1, is the result of work done on the Fe-Cr-Ti ternary system. Alloys containing less than 43 pct Cr were not investigated. In addition to this, a study of alloys in the Ti-Cr system was reported by McPherson and Fontana.² Adenstedt3 furnished a number of dilato-meter curves obtained from specimens containing 5, 10, and 15 pct Cr. Very recently, McQuillan4 submitted a proposed diagram covering the complete range of compositions between titanium and chromium. This diagram was in general agreement with the one described here. Experimental Procedure Sponge titanium (99.7 pct) and electrolytic chromium (Bureau of Mines analysis: 99.03 pct Cr, 0.40 pct Fe, 0.53 pct O2) were used for the initial determination of the system. Subsequent refinement of points, particularly for the low chromium side of the diagram, was accomplished by using iodide titanium and high purity chromium (National Research Corp. analysis: 0.050 pct C, 0.045 pct O2). The Ti-Cr alloys were prepared by melting 25 g charges in an enclosed, water-cooled copper crucible using a movable tungsten electrode. The atmosphere was helium, prepurified by first passing it through a drying agent and then through sponge titanium heated to 850°C. Particular care was taken to avoid any large scale segregation resulting from insufficient mixing of the components. Each charge was melted and kept molten for approximately 1 min, allowed to cool, inverted, remelted, and kept molten for an additional minute. In order to ascertain the amount of impurity pickup (oxygen and nitrogen) during the melting procedure, three iodide titanium specimens were melted in sequence and then checked for increased hardness. The specimens in the as-cast condition showed a relatively large hardness increase over the hardness of the as-received iodide titanium. The scattering on these readings was large. However, after the specimens had been homogenized at 840 °C for 2 hr and slowly cooled, the measured increase in hardness over the as-received titanium was small with a corresponding decrease in scatter. The reason for this hardness change is that in heat treating these specimens below the transformation temperature (885°C) there was a conversion from the as-cast structure to the more nearly equilibrium structure of the annealed specimen. The alloys were analyzed for chromium content and although the actual percentage was invariably low the deviation from the nominal composition never exceeded 0.6 pct Cr.

Jan 1, 1953

By George Burgess

1. Introduction.-THE methods of production of sound steel ingots have been described in several papers read recently before this Institute. It was thought by Director Stratton, of the U. S. Bureau of Standards, and ourselves to be of sufficient interest and importance, as a further contribution to this subject, to compare the properties of rails rolled in one mill according to American practice, from several types of ingot of substantially the same chemical composition but cast by several processes; and to compare in considerable detail the properties of an ingot manufactured by the Hadfield special-feeding process and one of the usual type for rolling into rails. We are greatly indebted to F. W. Wood, President of the Maryland Steel Co., who made this investigation possible by kindly placing his rail mill at our disposal; and he and his associates at Sparrows Point did everything possible to make the experiment a success, including the execution of several of the tests and analyses. 2. Classification and Manufacture of Ingots.-Of the ingots used in this investigation, eight were made in Sheffield and furnished by Sir Robert Hadfield, and one was made and furnished by an American steel company,' as a comparison ingot, and was supposed to represent the usual type of ingot from which rails are made.

Jan 2, 1915

By Alden B. Greninger

The study of mosaic structure of crystals1 has been confined until recently to the field of theoretical physics. Crystallographers, in general, have neglected the subject, although X-ray crystallographers constantly make use of formulas for intensities of X-ray reflection as modified by mosaic structure. Work on mosaic structure has centered chiefly on the task of proving or disproving the secondary-structure theory of Zwicky,² and very little attention has been paid to the visible imperfections of crystals. A. Goetz has been responsible for most of the supposed experimental confirmations of Zwicky's theory.3 On the other hand, Smckal,4 and Orowan,5 among others, maintain that there is neither theoretical nor experimental evidence to substantiate Zwicky's secondary structure. Lately the subject has been intensively investigated by Buerger,6 one of whose recent papers led to a symposium on mosaic structures.'

Jan 1, 1935

By A. E. Moss, J. K. Gustafson

MEASURED in terms of ore tonnage, the New Quebec and Labrador iron ore fields promise to rank with the greatest iron ore districts of the world. Over 400 million tons of high-grade ore for direct shipping have been discovered to date. Much greater amounts of lower-grade beneficiating ores are indicated by outcrops. Many hundreds of square miles of iron formation await testing. By 1954 iron ore will begin to move towards American blast furnaces, and shortly thereafter the annual rate of production is expected to reach 10 . million tons. To bring this vast project into being over $200,000,000 will have been spent for exploration and development, mining equipment, hydro plants, townsites, the building and the equipping of . a 360-mile railroad, and the construction of docks and ore-handling facilities. The most important iron ore deposits are located over 300 miles from tide water, see frontispiece and also Fig. 1. The frontispiece shows principal sources of iron ores and manganiferous iron ores for the U. S. and Canadian steel industry, and the major smelting districts are shaded on the map. No navi- gable rivers lead into the interior. When work was . commenced on this project there were no roads, no railroads, no communication ,system, no inhabitants, and no adequate maps either topographical or geological. The geological field season was limited to approximately 100 days per season. The obstacles facing this enterprise were many and varied. Its success will be due to the integrated team work of people of diverse skills. Explorers, Indian guides, prospectors, geologists, surveyors, mechanical, civil, electrical, and mining engineers,

Jan 1, 1954