Search Documents

By J. J. Arps

This paper reviews the methods currently in use for estimating primary oil reserves and discusses the principles on which these methods are based. Particular emphasis is placed on how these methods change with the type of information available during the life cycle of an oil property. This paper contains various novel estimating methods and shortcuts heretofore unpublished. INTRODUCTION Estimating oil reserves is one of the most important phases of the work of a petroleum engineer since the solutions to the problems he deals with usually depend on a comparison of the estimated cost in terms of dollars, with the anticipated result in terms of barrels of oil. His recommendations to management regarding the best course of action are therefore normally based on the most favorable balance between these two. Specific engineering problems which require such a knowledge of recoverable oil reserves and a projection of future rates are: [a.] the exploitation and development of an oil reservoir; [b.] the construction of gasoline plants, pipelines and refineries; [c.] the division of ownership in unitized projects; [d.] the price to be paid in case of a sale or purchase of an oil property, and the magnitude of the loan which it will support; [e.] the proper depreciation rate for the investment in oil properties; and [f.] evaluation of the results of an exploration program. This discussion will be confined to the various methods and tools which are currently in use for estimating oil reserves to be obtained during the primary phase of an oil-producing reservoir and for a projection of the future production rates. Reserves which may be obtained by secondary recovery methods or fluid injection programs and gas and gas condensate reserves will not be discussed in this paper. Unfortunately, reliable oil reserve figures are most urgently needed during the early stages when only a minimum amount of information is available. Management's interest in the oil recovery from a property—aside from its use for accounting purposes—usually declines when the property approaches its economic limit, just at the time when the reliability of the estimates is at its best. To illustrate this general idea a chart is presented (Fig. 1) showing the three periods in the life of an imaginary oil property. Time is shown on the horizontal axis, while the cumulative production and estimated ultimate recovery are plotted vertically. No particular units are used and this schematical chart is not to scale. During the first period, before any wells are drilled on a property, any estimates will of necessity be of a very general nature, based on experience from similar pools or wells in the same area, and usually expressed in barrels per acre. This will

Jan 1, 1957

Organization Place Date 1919 American Chemical Society :.... Philadelphia, Pa. Sept. 2-6 National Assn. of Stationary Engineers Huntington, W. Va. Sept. 8 American Peat Society Minneapolis, Minn. Sept. 22-24 American Iron, Steel Electrical Engineers St. Louis, Mo. Sept. 22-26 American Institute of Min. and Met. Engineers. Chicago, Ill. Sept. 22-27 American Steel Treaters' Society, First Annual Convention Chicago, Ill. Sept. 22-27 National Exposition of Chemical Industries.... Chicago, Ill. Sept. 22-27 National Safety Council Cleveland, 0. Sept. 29-Oct. 2

Jan 7, 1919

By C. L. Clark, J. Russ

For many years attempts have been made to develop a laboratory test that would serve to indicate the proper temperatures to be used in the various hot-working applications to which metals may be subjected as they are being processed from the cast ingot to the desired finished products. That these attempts have not been very successful is indicated by the fact that most of the temperatures in use today in these operations have been developed over a period of years by trial and error. In other words, the selection of the proper temperatures for the hot-working of metals is generally an art rather than a science. Our knowledge with respect to the behavior of metals at elevated temperatures has been greatly extended during the past several years. While most of the work in this field has been done at proposed operating temperatures of equipment, rather than at processing or fabricating temperatures, one outstanding fact has been developed, which is applicable to the entire high-temperature range; that is, that the rate of deformation to which the metal is subjected is of the same order of importance as the temperature. The failure to properly recognize this fact has greatly retarded the development of a suitable laboratory test for determining hot-working temperatures. Influence of Rate of Deformation on High-temperature Properties It is not the intent of this paper to survey all the work that has been done On the effect of deformation rate On the properties of metals. The importance of this factor, however, was shown by Zay Jeffries' as early as 1919, when he called attention to the existence of the so-called equicohesive temperature and to the effect of certain factors on the location of this temperature' Fig. I is a diagrammatic sketch showing the effect of temperature On the relative strength of the crystals and grain boundaries and the type of fracture that will res depnding On the location of the test, or Or temperature with respect to the equicOhesive temperature. Since the type fracture varies, it also follows that at temperatures below the equicohesive temperature the major deformation occurs in the grains: while at temperatures above, the deformation results either from the movement of the grains with respect to each other or recrystallization of the strained material occurs almost instantaneously, producing new crystals at the fracture. As previously indicated, it is an established fact that the position of this equicohesive temperature for any given metal is dependent On the deformation rate' For example, in 0.15 per cent plain carbon steel the location of this temperature under

Jan 1, 1947

By James P. Kimball

In a paper which I had the honor to present to the Institute at the Montreal meeting, September 1879,I took occasion to refer incidentally to certain practical difficulties in the sampling of coal-seams {Trans. Vol. VIII., p. 181-3). This reference was particularly to the unequal distribution of sulphur in the form of pyrite, and to the necessity of discriminating between the several members or " benches " of a coal seam as to their relative proportion of visible sulphur. What is a practically truthful estimation of the sulphur of a coal seam, is not necessarily the estimation of an average of sulphur in any given line of cross-section of the seam. Cornparatively speaking, the range of sulphur in quantity is generally so low that errors in its determination, arising from neglectful sampling or from slips in the laboratory, fall chiefly upon this single ingredient. Not so,

Jan 1, 1884

By W. E. C. Coxe

AT the meeting of the Institute in Philadelphia, in June, 1876, it was my pleasure to read a paper on the "Manufacture and Endurance of Iron Rails." I then spoke of some trial rails which had been placed in the down track of the Philadelphia and Reading Railroad, over which passed, in addition to merchandise and passengers, most of the heavy coal traffic of that company. One of these rails, made at the Philadelphia and Reading Rolling Mill in 1870, and then placed in the track, was removed in 1876, after having carried about 55,000,000 gross tons, and was on exhibition at the Centennial Exhibition. A piece of this worn rail, twisted cold, was also shown there. One of the same series of rails was allowed to remain in the track until 1878, and short sections of this rail, as well as one not worn, to show its original shape, are presented for your inspection. A comparison of the two will show that the top of the head or tread has worn down 3/16 ths of an inch during its nine years of service. It carried in that time 67,000,000 gross tons of freight, passengers, cars, and engines. This rail was made in the usual way of manufacturing iron rails at the Philadelphia and Reading Rolling Mill. The head was made from puddled iron bars, piled, heated, and rolled into bars, 4 1/2 and 3 inches wide by 1 inch thick, these bars, breaking joints, were made into a pile in section 9 inches square, heated and rolled into slabs 9 inches wide and 2 inches thick; the balance of the rail-pile was made of 4 1/2 and 3-inch bars, rolled from two-thirds old rails and one-third puddled iron, the

Jan 1, 1880

By Clyde Orr

INTRODUCTION Cracks, crevices, holes, and fissures -- here collectively termed pores -- occur in all manner of substances in sizes from those evident to the unaided eye to those well below electron microscopic levels of detection. Naturally occurring materials having varying degrees of porosity are represented by wood, rock, soil, and mineral formations. Man-made materials that are porous include ceramics, sintered metals, catalysts, adsorbents, filters, and various compacted objects. The extent of their porosity greatly influences the hardness, rigidity, integrity, and general usefulness of such materials, and assessing both their pore volume and size is becoming increasingly necessary. Means by which this pore information can be obtained is the subject here. No attempt will be made to include all techniques and variations of them that have been suggested, but, hopefully, those of most general applicability will be described in sufficient detail to enable a potential user to judge their merit for a particular need. The results of pore measurements are made useful by relating them through other tests to performance criteria such as weatherability, water penetration, frost damage, oil recovery, strength, or thermal or electrical conductivity. These tests, of course, are outside the bounds for inclusion here. A pore is variously defined in dictionaries as "a minute opening", "a small interstice admitting passage of liquid", and "an interspace between particles". Clearly any object through which it is possible to find a continuous path from one side to the other either for a liquid or a gas must be regarded as porous. Passageways are not necessary for porosity to exist, however. There are so-called blind

Jan 1, 1980

For the year ending February, 1917 PRESIDENT L. D. RICKETTS,1 NEW YORK, N. Y. PAST PRESIDENTS BENJAMIN B. THAYER,1 NEW YORK, N. Y. WILLIAM L. SAUNDERS,2 NEW YORK, N. Y. FIRST VICE-PRESIDENT SIDNEY J. JENNINGS1 NEW YORK, N. Y. TREASURER GEORGE C. STONE,1 NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND, NEW YORK, N. Y. SECRETARY . BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 5, 1916

By Joseph D. Weeks

When I presented at the Chicago Meeting of the Institute, in May, 1884, a paper on Hadfield's manganese steel,* which had about that time been brought to the notice of steel manufacturers, I promised to furnish some physical tests of the steel for publication in the Transactions. The fulfilment of the promise then made has been delayed by various circumstances; but I have recently been put in possession of tests of this steel carefully made at the Woolwich, England, arsenal. Messrs. Hadfield & Co. prepared for the arsenal a series of twelve test-pieces, made from the same heat. An analysis of the steel gave the following results: Carbon,.........73 Silicon,.........37 Sulphur,.........06 Phosphorus,. .08 Manganese,...... 9.83 The test-pieces had been heated to a white heat and plunged into cold water prior to being put into the machine. This treatment

Jan 1, 1887

By W. H. Wamsley

Used in combination with conveyor belt haulage, bucket wheel excavators offer unusual possibilities for low excavation and haulage costs. Originating in Germany, these machines are now in use or on order for Australia, Northern Rhodesia, the Belgian Congo, Italy, Yugoslavia, France, Belgium, Indonesia, and the Union of South Africa. A diamond mine in South Africa that has been using German bucket wheel excavators since 1928 purchased American cable-way excavators and American scraping equipment after the war. Operating cost for this equipment was double that for the bucket wheel machines operating in the same mines with crawler-mounted stackers. Machines built and operated in the U. S. are, as far as the writer knows, confined to the northern Illinois coal field, where they are used in conjunction with large shovels to strip overburden too high to be reached by the 30 to 40-yd shovels. Their long stacker belts can deposit the spoil far enough behind the coal face to avoid slides, in such a manner as to make reclaiming the land easier. These large, specialized machines are now being made by Bucyrus-Erie Co. but are not adaptable to many open pit mining situations.

Dec 1, 1956

By R. W. Parsons, P. R. Chaney

Oil recovery by the imbibition mechanism can be important in fractured carbonate reservoirs with a bottom water drive. Laboratory experiments were performed on water-wet carbonate rocks to model this process. The results are interpreted in light of the applicable scaling laws. The imbibition production behavior of a pillar of rock subjected to a slowly rising water table can be synthesized from data on total immersion experiments on small rock samples. If the rate of water table rise is slow enough and if the physical properties are such that the imbibition zone is of a small vertical extent, then only the final oil recovery on the small samples need be known. Applying laboratory imbibition data to a real reservoir should be done with caution because of possible wettability problems and the unknown behavior of two-phase flow in fractures. INTRODUCTION The spontaneous taking up of a preferential wetting fluid into a porous medium with the simultaneous expulsion of the contained fluid is termed imbibition. One of the many physical imbibition processes is the production of oil by the taking up of water into a water-wet reservoir rock. In certain types of heterogeneous reservoirs, e.g., fractured, it is realized that imbibition alone may be the dominant mechanism. Theoretical studies of imbibition oil recovery have followed several lines of attack. The behavior of certain mathematically tractable and conceptually simple models have been analyzed. Birks1 considered a bundle of vertical capillaries model, while Perotti et al.2 and Kelemen3 used a model of a series of vertically oriented fractures. If the oil production behavior from a block of reservoir rock is known, then the cumulative behavior of a vertical stack of these blocks subjected to a rising water table can be determined by a method outlined by Aronofsky et al. 4 Knowing the capillary pressure and relative permeability functions should uniquely set the imbibition behavior for a given sample. Solutions of the partial differential equations describing the process, however, present some formidable problems. Digital computer techniques have been applied to displacement processes in which the capillary pressure has been included.5"8 More recently, similar techniques have been used by Blair 9 to calculate countercurrent imbibition behavior. The fact that imbibition behavior is described by the usual fluid flow equations (Darcy's Law and continuity equation) implies that the derived scaling laws should apply equally to this situation. Use of model experiments to study imbibition has been employed by Graham and Richardson 10 and Mattax and Kyte,11 who actually tested the scaling law applicability. This study is concerned with scaled model imbibition experiments on water-wet carbonate rocks. Of particular interest is the slowly rising water table experiment. This simulates a highly fractured reservoir with the water table rising uniformly through the vertical fracture system. Experiments were performed on different sized samples and with different rates of rise of the water-oil interface surrounding the rock pillar. Total immersion imbibition experiments on smaller rock samples were performed to test the basic linear scaling laws and to see if these simpler tests could be used to synthesize the rising water table experimental results. THEORY IMBIBITION SCALING LAWS Scaling laws for the flow of two incompressible immiscible fluids in a porous medium have been presented by Rapoport.12 These are derived directly from Darcy's Law for the individual phases and the continuity equation. Results from a laboratory model experiment will duplicate those from some reservoir prototype if a constant proportion is maintained among the three forces acting on the fluids — the capillary pressure gradient, the gravitational gradient and the flowing pressure gradient. Operation of the model (i.e., fluid injection or withdrawal) must be conducted in accordance with specific equations. If the

Jan 1, 1967

By Thomas M. Tharp

INTRODUCTION Attempts to analyze the stability of slopes, foundations and underground openings in discontinuously jointed rock have generally assumed full joint continuity or ignored the role of stress concentration at the tips of discontinuous joints. The most common approach in rock slopes is to consider a failure plane consisting of coplanar, but discontinuous joints separated by intact rock. The intact rock is assumed to fail in shear as a Mohr- Coulomb material and to contribute a strength component proportional to the fraction of the failure plane that is intact rock (Jennings, 1970). An alternative approach by Stimpson (1978) applies Lajtai's (1969) theory for shear strength of discontinuously jointed rock masses to slopes. Lajtai allows tensile failure in the intact rock of a composite surface. This theory yields lower shear strength than that of Jennings (1970) except in the presence of high normal compression, however it also fails to account for the stress concentration at the tip of a discontinuous joint. For a given slope geometry, stresses increase with slope height, but in both of these models rock mass strength is independent of size. A fracture mechanics analysis shows that particularly for small slopes, rock mass strength decreases with size. A continuous stepped failure surf ace produced by propagation of preexisting joints may develop at lower shear stress than predicted by the Jennings (1970) or Lajtai (1969) models. This fracture mechanics model applied to slopes in competent rock is more realistic in its assumed failure mechanism, and for large slopes more conservative than the Jennings (1970) or Lajtai models (1969).

Jan 1, 1984

By A. Mitchell, T. Bagshaw

A recent paper by Thomas1 has presented new data on the solubility of hydrogen in solid silver at 1 atm pressure in the temperature range 600° to 963°C. However, no data is reported in the literature on hydrogen solubility in liquid silver. The Sieverts technique which has been described previously2,3 was used in the present work. Charges of approximately 160 g were melted in Morgan "purox" recrystallized alumina crucibles and purified helium was used for the determination of the "hot volume" during each experiment. A chemical analysis of the silver indicates that the impurity content (Cu + Al) is less than 0.02 wt pct. Hydrogen solubility in the temperature range 963° to 1200°C was investigated. The results of three experiments are shown in Table I. Fig. 1 shows an Arrhenius plot of the present work together with the solid-state data of Thomas, Steacie, and johnson,4 Eichenauer et al.,5 and Siegelin et al.6 The following expression has been derived from the Arrhenius plot of the present data: log (solubility of hydrogen, cm3 per 100 g) = 2.154-3512.0/ToK The heat of solution derived from Fig. 1 is 31,150 cal per g mole H2 compared with the value of 33,020 cal per g mole H2 obtained by Thomas and 12,000 cal per g mole H2 obtained from the data of Steacie. It was observed that hydrogen evolution took place when the silver melts were solidified under 1 atm of hydrogen, which would not be expected from an extrapolation of the results of Steacie. Schenck and Lange7 have observed that, for several transition metals at their melting points, the ratio of the hydrogen solubility in the liquid to that in the solid lies in the range 2.1 to 3.1. The present results and those of Thomas are in accord in this respect having a ratio of 2.8. 'C. L. Thomas: Trans. TMS-AIME, 1967 vol. 239, pp. 485-96. 2T. Bagshaw and A. Mitchell: I. Iron Steel Inst., 1966, vol. 204, p. 87. 'M. Weinstein and J. F. Elliott: Trans. TWS-AIME, 1963, vol. 227, p. 382. 'E. W. R. Steacie and F. M. G. Johnson: Proc. Roy. Soc. (London), Ser. A, 1928, vol. 117, pp. 662-79. 'W. Eichenauer et al.: Z. Metallk., 1958, vol. 49, pp. 220-25. 6W. Siegelin et al.: Z. Elektrochem., 1957, vol. 61, pp. 359-66. 'H. Schenck and K. W. Lange: Arch Eisenhuettenw., 1966, vol. 37, no. 9, pp. 739-48.

Jan 1, 1969

By Albert Sauveur

My first paper dealing with the theories of the hardening of steel by rapid cooling was published in the Transactions of this Institute in 1896— 30 years ago-under the title "The Microstructure of Steel and the Current Theories of Hardening," hence, also, the title of the present paper. It was extensively discussed and was, I believe, one of the starting points of many subsequent papers and discussions of the same subject, dis-cusssions which at times became almost violent and which led to the formation of different schools such as the "Carbonists" and the "Allo-tropists." Some of the older members of the Institute, who took part in the debate or who were interested observers, will, I am sure, have kept a vivid remembrance of it. The controversy gradually quieted down, apparently for lack of ammunition, without any side acknowledging defeat. Recently, however, interest in it ha been revived through the claims of some that these vexed questions had at last been solved. In an effort to ascertain if possible the prevailing view of those best qualified to express an opinion a questionnaire was submitted to the following gentlemen: J. 0. Arnold Sir Robert Hadfield Edgar C. Bain W. H. Hatfield Carl Benedicks Samuel L. Hoyt N. Belaiew Kotaro Honda H. M. Boylston Zay Jeffries Harry Brearley H. Le Chatelier G. K. Burgess H. H. Lester William Campbell Francis F. Lucas H. C. H. Carpenter John A. Mathews Pierre Chevenard A. McCance P. Dejean Albert Portevin C. A. Edwards Walter Rosenhain F. Giolliti Bradley Stoughton G. Grenet F. C. Thompson Leon Guillet

Jan 1, 1926

By R. P. E. Hermsdorf

THE electrolytic refining of metals for the removal of undesirable impurities has become a recognized necessity in the nonferrous field. Copper, lead, zinc, nickel, silver and gold have been produced in this manner for years. The United States Metals Refining Co., realizing that considerable quantities of lead and tin could be made available to the trade if a satisfactory method of purification of these metals could be established, decided to investigate the possibilities of electrolytic solder. In cooperation with Dr. Edward F. Kern, of the School of Mines at Columbia University, the company developed a process of electrolytic refining of lead-tin alloys using a tin-lead fluosilicate electrolyte. A pilot plant was installed in November, 1927, and the commercial unit was put in October, 1929. Since that time thousands of tons of electrolytic solder have been produced in this plant and consumed by all branches of industry that use solder.

Jan 1, 1936

By J. A. Elias, A. J. Heckler

A simplified method is described for the prepauatior~ of comnposite samples for determination of one quadrant of an X-ray pole figure of a sheet material by the Schulz reflection method. Other special conzposite sampling methods were used to investigate specific areas of the pole figures. Plotting nets for these sampling plans were drawn by a computer. Step-scanning techniques were used to obtain detailed information about specific regions of a pole figure. Satisfactory pole figures were obtained for large-grained (0.5 to 1 in. diam) sheet materials. COMPOSITE sampling techniques for preparing one quadrant of an X-ray pole figure have been reported by a number of authors.'-5 All of these methods are similar in that they use a composite sample prepared by stacking and holding together coupons cut from a sheet material. The schulze reflection technique is applicable to the composite sample so that only minor corrections are needed for defocusing and absorption effects. Also, a relatively large area of a sheet is sampled through the use of multiple cross sectional pieces. In general, sampling methods necessary to obtain a composite-type specimen have been formidable enough to discourage their use in routine pole figure determinations. This paper presents a versatile sampling technique which is simpler than those previously described along with an accurate method for obtaining stereographic plotting nets for any orientation of a composite specimen surface. A step-scanning technique is used to obtain more quantitative determinations of specific regions in pole figures, and the composite technique is satisfactorily applied to determine pole figures of very large grained sheet materials. REVIEW OF PREVIOUS TECHNIQUES Mueller and ~nott' first proposed a technique for obtaining one complete quadrant of an X-ray pole figure by using a sheet sample and six different composite samples in which the individual coupons were aligned and held together by two types of jigs. Data from the seven different samples were overlapped to obtain a single quadrant. ~eieran~ and Lopata and ~ula~ obtained a complete quadrant of a pole figure from a single sample prepared by forming a cube from coupons cut from a sheet. These coupons were bonded together using an epoxy cement, and a cut was made at 54.7 deg to the normal, transverse, and rolling directions of the sheet, Fig. I. The normal direction of the cut face projects into one quadrant of a stereographic projection at equal angles to the three principal orthogonal reference directions mentioned above. X-ray reflection data obtained along a spiral path in physical space could then be plotted on a stereographic net offset 54.7 deg from the normal, as shown in Fig. 2. A rotation about an axis representing the surface normal is designated as a, and a rotation about an axis lying in the plane of the surface is 4. From Fig. 2 it is apparent that a tilting angle of no more than 55 deg @ is necessary to obtain the complete quadrant. ~eber~ devised an improved sampling technique by cutting coupons 45 deg to the rolling direction of a sheet, stacking and bonding these with an epoxy cement at an angle of 54.7 deg to a reference plane, and finally grinding and lapping a flat specimen surface parallel to this plane. An important consideration of this technique and that of Lopata and ~ula~ is variation in the diffracting power of the specimen surface due to the bonding medium. While any composite-type sample will have some such variation due to boundaries between coupons, the problem can be minimized by elimination of the bonding medium and by avoiding prolonged etching times which could lead to significant inter lame llar attack of the coupon faces. EXPERIMENTAL TECHNIQUE We were working concurrently though independently on a technique similar to ~eber's,' but which does not

Jan 1, 1968

By M. C. Flemings, T. Z. Kattamis

Dendrite morphology and grain size were studied in bulk samples of iron and nickel base alloys under-cooled up to 300°C. In the alloys studied, dendrite morphology gradually changes with increasing undercooling from the usual dendritic structure to a structure composed of cylindrical dendrite arms. At a critical undercooling of approximately 170°C in these alloys there is an abrupt transition to a fine-grained structure of spherical morphology. Final dendrite-arnz spacing of melts nucleated at less than the critical undercooling decreases with increasing undercooling and with decreasing distance from a chilled surface. Grain size of melts nucleated at greater than the critical undercooling decreases similarly with these factors. It is concluded that structure coarsening, with reduction of surface area as driving force, is the principal mechanism determining final dendrite-arm spacing in melts nucleated at small undercoolings and grain site in melts nucleated at large undercoolings. IN solidification of highly undercooled melts, nuclea-tion and growth of the solid is accompanied by a rapid release of latent heat of fusion. The heat release is sufficiently rapid in bulk specimens that it takes place essentially adiabatically with respect to the surroundings; hence the specimen heats up ("recalesces") to some maximum recalescence temperature. For bulk liquid metals and alloys, a simple thermal balance shows the undercoolings obtainable in bulk samples are not sufficient to lower the maximum recalescence temperature below the equilibrium solidus temperature. Hence, some liquid always remains at the end of recalescence; this liquid must solidify by rejection of heat to the surroundings. Metals, including iron and nickel base alloys, normally freeze with only a few degrees of undercooling. In general, nucleation begins on impurity particles present in the metal, at a "heterogeneous nucleation temperature" that is quite close to the equilibrium liquidus temperature. Very small droplets of metal can be undercooled considerably before nucleation occurs,1-4 presumably because subdivision of the liquid reduces the probability of solid impurity in a given droplet. Following early work on metal droplets,' a series of studies has shown that it is possible, without great difficulty, to undercool bulk samples of many metals and alloys. Undercoolings obtainable are approximately two tenths of the melting point for nickel, iron, copper, and other metals and alloys.5-9 Specimen sizes have generally been in the range of 50 to 500 g. Studies on undercooling to date have been concerned primarily with techniques of undercooling and with nucleation and growth kinetics. Only limited consideration has been given to dendrite morphology in under- cooled alloys. One such study, in bulk Cu-Ni alloy,8 showed that at small undercoolings a typical dendritic structure was obtained. At undercoolings the order of 175°C the structure of a Cu-40 pct Ni alloy became "ray or starlike", and a dense network of subbound-aries appeared. At still larger degrees of undercooling, of the order of 250°C, the structure became more random and included an ensemble of globular forms. Comparable results were obtained by walker10 on Cu-Ni alloys, and by Kamenetskaya et al.11 in research on Cu-Ni, Sb-Bi, Fe-Ni, and Fe-Cr alloys. In this work, study was made of the processing parameters influencing dendrite morphology and grain size in undercooled alloy melts. Experiments were specifically designed to show the effects of coarsening ("ripening") during solidification on final casting morphology. EXPERIMENTAL PROCEDURE Apparatus used was patterned after that of Walker,10 Fig. l(a). Melting was by induction under reduced pressure of helium. Two different types of crucible materials were used; there was no difficulty in obtaining substantial undercooling in both types of materials. Alumina crucibles were used for the bulk of the runs made, with a glass coating separating the metal from the crucible walls. Other runs were made using fused silica crucibles with or without slag coating. A graphite susceptor was employed around the crucible to aid in melting and to reduce melt stirring. The major portion of the experimental work was on

Jan 1, 1967

PRESIDENT AND DIRECTOR R. C. ALLEN . CLEVELAND, OHIO PAST PRESIDENTS AND DIRECTORS H. A. BUEHLER ROLLA, Mo. JOHN M. LOVEJOY NEW YORK, N. Y. VICE-PRESIDENT, TREASURER AND DIRECTOR KARL EILERS NEW YORK, N. Y. VICE-PRESIDENTS AND DIRECTORS HENRY KRUMB NEW YORK, N. Y. PAUL D. MERICA NEW YORK, N. Y. H. G. MOULTON NEW YORK, N. Y. HARVEY S. MUDD Los ANGELES, CALIF. WILFRED SYKES CHICAGO, ILL..

Jan 1, 1937

News has just been received that Flight Commander William T. Hall, a Junior Member of-the Institute, was killed in action on Saturday, May 19, 1917. According to the' Toronto Star, Commander Hall was 24 years of age, a native of Toronto, and a grandson of the late William Kersteman. During the four years of his course in mining at the School of Practical Science, Toronto University, he passed every examination with honors. When war was first declared Commander Hall endeavored to join the artillery as an officer, and for that purpose secured a provisional lieu- tenancy with a Hamilton battery, but he did not receive an overseas appointment, and on being graduated as a mining engineer in 1915, he was offered a position in Chile, which he accepted. He left Toronto on May 27, 1915, and was engaged in Chile as a mining engineer for nearly a year. In the latter part of April, 1916, he decided to offer himself again for service at the front. He crossed the Andes and sailed for Liverpool, where he landed on May 13, 1916. On May 27, 1916, Capt. Hall was given a commission as lieutenant in the Royal Flying Corps. He went to the front on Sept. 1, 1916, and remained there continuously. On April 4, 1917, he was promoted from lieutenant to the rank of flight commander. No details of how Commander Hall came by his death have as yet been received.

Jan 1, 1918

By Walter Knox, J. D. Doherty

IN 1939, at the request of The Koppers Coal Co., the Koppers Company Research Department established a Stoker Coal Research Laboratory for the purpose of investigating the performance characteristics of stoker coals in typical domestic stoker installations. Fig. I is a photograph of part of the laboratory. The material in this paper deals with the performance of one coal in a single installation. Presented are details of this installation, mechanical characteristics of the stoker, and the results of a series of burning tests in which adjustments were systematically varied. SUMMARY OF RESULTS Mechanical Features I. A large percentage of the total power consumed by a domestic stoker is used to operate the gear case and motor (Fig. 3). 2. The power consumption per ton goes down with an increase in rate of coal feed (Fig. 4). 3. The automatic air control in this stoker showed advantages over manual control (Fig. 5). 4. The air velocities through the retort tuyeres were uniform around the retort, but varied between the rows of tuyere rings (Fig. 6). 5. The crushing of coal with this stoker increased the minus 1/8-in. from 1 1.6 per cent to 19.2 per cent. There was a noticeable segregation of coal as it came from the retort and distribution was not uniform (Fig. 7). 6. Measurement of air entering over the fire showed that with some not uncommon adjustments this air may he a high percentage of the total air supply (Fig. 8 and Table I). Operating Performance I. The removal of clinker was shown to give a period of poor performance characterized by a high fuel-bed resistance and a high percentage of carbon monoxide in the flue gases (Fig. 10). 2. The fuel-bed resistance was found to decrease as the fuel bed built up in a normal response to heat demand after a prolonged hold-fire (Fig. II). 3. With intermittent operation the burning rate was almost always less than the feeding rate. The wide variations were found to be greatly dependent upon the length of the On period and the length of the intervals between On periods (Fig. 12). 4. The maintenance of a low furnace draft led to less fly ash, better clinker formation, and higher efficiencies (Fig. I3). 5. The maintenance of a minimum of excess air also resulted in less fly ash, better clinker formation, and higher efficiencies (Fig. 14). GUIDING PRINCIPLES In planning the investigations, the following principles were adopted: Selection of Healing Equipment.-Use only standard models of stokers and furnaces representative of those widely used.

Jan 1, 1942

By D. R. Uhlmann, T. P. Seward, O. Chalmers

A magnetic field has been used to damp out liquid convection during the solidification of castings. Ingots of Al-2 pct Cu were poured from various sperheats (10" to 65°C) into a room-temperature graphite mold located between the poles of an electromagnet. The effect on ingot structure of varying the strength and time of application of the magnetic field was investigated, and the results are interpreted in light 01- current theories of ingot structure. In the solidification of alloy systems, thermal gradients in the melt and differences in density of the constituents are expected to produce convective motion in the liquid. The thermal convection caused by temperature gradients should be present during the freezing of both alloys and pure materials, while the solute convection caused by density differences should be of concern only for alloys. The possible influence of this natural convection on the structure of castings has been discussed by Ruddle,' Chalmers, and Tiller. More recently, an experimental investigation of such effects was carried out by Cole and Bolling. These workers took stationary molds containing lead- and tin-based alloys and. using a brine solution. quenched them from various superheats above their respective liquidus temperatures. When grids were placed across the mold diameter to suppress convection, the grid region was later observed to contain a larger percentage of columnar grains than other parts of the casting or than similar castings poured without the grids present. From thermocouple measurements, they found the temperature in the grid region to be higher than that in the region outside the grids throughout the freezing process, and concluded that convection should be an important mode of heat transfer in normal castings. In addition to such convection arising from thermal gradients or differences in density of the constituents, a further source of convective motion, which we shall call "momentum convection", may be particularly important in small (laboratory-size) castings. By this term we refer to the convective motion produced in the initial pouring process, a motion which is damped out as the linear momentum and angular momentum of the liquid are dissipated. Besides these sources of convection, which are present to some extent in all castings. external influences may also be effective in producing convective motion. Examples of such "forced" convection which have been discussed in the literature include stirring the melt, shaking the mold, rotating the mold, and so forth The purpose of the present study was to examine the effect of convection on the structure of castings poured into a cold mold. In this work, a magnetic field was employed to damp out the convective motions within the liquid, and hence control the extent of con- The effect of a magnetic field on convective currents in a conducting liquid is to induce eddy currents which oppose and damp out the convective motion. vection. The technique of magnetic damping was previously used by Utech and F1emings" in their study of convective effects on impurity banding and other substructure in alloy crystals grown unidirectionally from the melt. In their investigation, fields as small as 200 gauss were found to be effective in damping the convection currents which influence the banding. I) EXPERIMENTAL TECHNIQUE In the present study, alloys of A1-2 wt pct Cu were poured into a room-temperature graphite mold. The mold, in the shape of a circular cylinder, 2 in. ID, 2-3/4 in. OD, 5 in. inside height, and 5-1/2 in. outside

Jan 1, 1967