Search Documents

By John J. Collins

[CONTENTS PAGE Purpose and scopeI Core samplingI Sludge sampling.....7 Combining core and sludge assays13 Deviation and surveying of drill holes17 Conclusions24 Acknowledgments25 Bibliography25] PURPOSE AND SCOPE The purpose of this paper is to review a few of the problems involved in the interpretation of diamond-drill core and sludge samples, with the hope that it will stimulate discussion and bring forth some of the information on the subject that has been accumulated by various organizations. The release of these data would benefit the mining industry as a whole. Particularly valuable would be the details of drilling programs that have been tested by actual mining operations, as most of the available published material is unsupported by production records. The scope of this paper is limited to a few of the commonest problems of interpreting diamond-drill core and sludge samples and the deviation of holes. It does not include the description of routine operations performed by the drillers, nor the estimation of ore reserves. The methods of calculating reserves have been described 25,26,31,32.50,65 but more information is needed on the results shown by actual mining operations. CORE SAMPLING The accuracy of diamond-drill-hole sampling depends in large measure on the percentage of core recovery. As a general rule, the longer the run, the poorer is the recovery. Although the longer runs allow cheaper drilling costs, the determining factor should be the percentage of recovery desired. The problem is one of balancing accuracy against costs. Holes of larger diameter may show improved recovery, except as Joralemon* points out that there are some conditions in which small holes give better core recovery than large holes. This is particularly true, he says, in rocks like shattered quartzite, where larger core tends to break in angular fragments and grind up, while the diameter of smaller core is less than the distance between joint planes and grinding is not so serious. In a large measure the length of the sample run should depend on the type of deposit. Favorable drilling may allow uniform sample runs of 5 ft., 10 ft., or perhaps 20 ft. In veins or beds of relatively narrow widths and changing characteristics, however, the ore zone may be overrun and ground in a core barrel full of waste rock. Generally it is desirable to break the sample at a change in the rock or ore. Such a change, often indicated by a color change in the sludge water, should be a signal for the driller to make a "dry" block and to pull out that run regardless of the length. Such a procedure permits the segregation of waste from ore samples so

Jan 1, 1946

By L. M. Litz

Study results are presented in which gaseous oxygen was dissolved in the leach liquor at concentrations of the order of 300 ppm. This oxygen-containing solution was injected into portions of a field being operated on a commercial basis with hydrogen peroxide as the oxidant. Comparative results indicate that uranium concentrations and production rates were essentially equivalent with these two oxidants.

Jan 1, 1983

By Frank L. Gaddy

Falls of roof account for over 50% of the fatalities that occur in coal mines in the US. Thus, roof control is one of the more important phases of underground mining. In reality, the control of roof influences the system of mining and is a major determinant of the width and spacing of working places, operations at the mining face, ventilation control, and surface subsidence. Frequently, the control of roof is the largest single cost item. Roof control is a never-ending task, not only at the working face and throughout sections where men are working, but along haulways and air- ways that must be maintained for the life of the mine. This is because roof, even the hest of roof, slowly deteriorates, so it must be frequently examined, with corrective support applied when needed. As coal is excavated, stresses are set up in the roof because the previous equilibrium is upset, resulting in pressures that cause fractures and slight movements that are frequently hard to detect. Unless the immediate roof, in the excavated area, is given support by artificial means, it might fall or there might be a succession of falls, varying from a thin scale to several feet, depending on the nature of the top. Exceptions to this are those rare mines, or sections of mines, with hard, strong, nonweathering roof that requires no support. GENERAL CLASSIFICATION OF ROOF There are two broad types of roof as far as support is concerned: the immediate roof above the coal and the main roof. Artificial support for mining purposes is only concerned with the immediate roof as nothing except large blocks of solid coal, or massive concrete, will support the main roof. The immediate roof is generally a few feet thick but call vary from inches to 6.1 m (20 ft) or more. There are examples of where there is no imrncdiate roof as the massive main roof lies directly on the coal

Jan 1, 1981

By Sherman L. Pease

An inexpensive and relatively rapid method that can be used by field crews is described. Fluid movement is determined by releasing a tracer (dye) in the well at a predetermined level and, after an interval of time, sampling the well fluid at another level. The testing equipment consists of a combined crusher and sampler unit that is run into the well on a wire line. The rate of movement can be calculated from time-volume relationships. Description of Method It is often desirable to determine whether there is occurring any transfer of fluid from point to point in a shut-in well, and, if so, to measure the rate of movement. When it is desired to examine a large number of wells for possible "thief" sands, the time and expense will be considerable unless the method used is inexpensive and rapid. After experimentation with several possible solutions to the problem, the Production Department of the Shell Oil Co., Inc., developed the apparatus described herein, which has proved satisfactory. Routine operations with it can be carried out by field production crews with a minimum of technical supervision and with negligible investment in equipment. The method is based upon releasing a suitable tracer in the well fluid at a known level, and recovering a sample of well fluid at another level after a measured interval of time. Repetition of this process with different time intervals between release and sampling gives the necessary data. For purposes of illustration, the setup for measuring migration of fluid in an upward direction is described in the following paragraphs. The arrangement of equipment is shown diagrammatically on Fig. I. The elements of the combination unit are the tailpiece, the crushing device, the spacer and the sampling device. The lengths of the tailpiece and spacer are varied to place the crushing and sampling devices in the desired positions in relation to the sands being tested. The crushing device breaks the glass bottle containing the tracer when the tailpiece strikes the bottom of the well and the tension on the sand line is slackened. Because of the open construction of the crushing device, the tracer is quickly and completely disseminated in the well fluid. The sampling device is a suction bailer, which obtains a sample of the fluid surrounding the perforated nipple just before the unit is picked up off bottom. The sample is retained in the barrel by the ball valve for examination at the surface. Normally, on the first run into a well, the sample is obtained near the releasing point of the tracer, and thereafter samples are taken near the base of the upper sand if migration is indicated by the dilution or absence of the tracer in the initial sample. The length of the time interval between the releasing of the tracer and the sampling of the well fluid is varied for successive runs, attempting first to establish the rate within limits and then to define it more accurately by additional runs if necessary.

Jan 1, 1946

By William C. Buell

As used in connection with open-hearth or other high-temperature operations, "insulation" refers to a multitude of substances, natural or manufactured, that have the one principal property of preventing the flow of heat by conduction to a greater degree than refractories can prevent it, the principal properties of the latter being resistance to temperature and/or chemical action. The term "control" as commonly applied to the mechanization of management functions is inappropriate without qualification, for without some degree of control of every operation we could produce no steel worthy of the name. Although grouped together in this paper, insulation and control in open-hearth furnaces have little, if any, interrelationship, therefore the paper is made up of two distinct parts. INSULATION OF OPEN-HEARTH FURNACES More than ten years ago the writer proposed the insulation of an acid open-hearth furnace system below the charging floor, and it was accomplished, with gratifying results. Possibly that was the first time the insulation of regenerators and slag pockets of any open-hearth furnace was undertaken, but shortly thereafter such insulation became general, and when the six groups of 15D-ton furnaces' were built in 1929-1930, they were completely insulated below the charging floor. While the practice was accepted at least five years ago, it was not well understood, however, as indicated by the following incident which occurred in connection with an installation made in 1929. After the

Jan 1, 1935

By Douglas Ashmead

In his paper Mr. Braley makes no mention of the bacteriological aspects of the problem. It is now quite well established that certain bacteria play a major role in formation of acid mine waters, and it is a simple matter in the laboratory to show that under sterile conditions the rate of acid production from a pyrites suspension is only about one quarter of that obtained from a similar suspension inoculated with drainage from a mine producing an acidic pit water. Under sterile conditions the oxidation is due to direct chemical action and, from the evidence just given and from much other evidence, this increase under nonsterile conditions is due to certain bacteria. Experiments recently completed, and shortly to be published, have shown that this bacteriological oxidation can be prevented by the maintenance of pH conditions above 4. It was found that to raise this pH above 4 at the beginning of the experiments was not sufficient but that, due to the continuing chemical oxidation, alkali had to be added daily to maintain the pH conditions above 4. The amount of alkali added, however, over a fixed period, was only about one quarter of the alkaline equivalent of the acid produced when pH conditions were not controlled over an equal period. The opinion expressed by Mr. Braley that sodium hydroxide has little or no effect on the rate of oxidation of pyrites is not substantiated by the above experiments. The writer does not claim that these results show a practical solution to the problems, especially in abandoned workings, but feels that the application of an alkaline coating, such as lime wash, to exposed accessible workings might be well worth trying. S. A. Braley (author's reply)—In 1919 Powell and Parrl suggested that bacteria, or some catalytic agent, hastened the oxidation of pyritic or marcastic sulfur in coal. Carpenter and Herndon (1933)' attributed the action of Thiobacillus thiooxidans. Colmer and Hinkle (1947)3 observed an organism similar to T. thiooxidans and another organism that oxidized iron. Leathen and Braley 9rst discovered this organism in 1947 in a sample of water from the overflow of the Bradenville mine (Westmoreland County, Pennsylvania). They characterized the organism in 1954" and gave it the name Ferrobacillus ferrooxidans. Although Temple and Colmer (1951)' had suggested the name Thiobacillus ferrooxidans, since they claimed it oxidized both ferrous iron and thiosulfate, we have found that pure cultures of the organism do not oxidize thiosulfate, hence the name F. ferrooxidans. In 1955 Ashmead7 isolated an organism, similar to the one called Thiobacillus ferrooxidans by Temple and Hinkle, from acid mine water in Scotland. It is probable that this organism was F. ferrooxidans. In 1954 Bryner, Beck, Davis, and Wilsonh reported microorganisms in effluents from copper mine refuse. These organisms appeared to be similar but were not in pure culture. In view of this history of bacterial investigation of acid mine water and our own ten years of experience, we do not agree with Mr. Ashmead that bacteria play a major role in acid formation. We do not find that any of these bacteria will directly oxidize pyritic material. They do, however, augment the chemical formation of sulfuric acid by atmospheric oxidation. In two papers in 1953% eathen, Braley, and McIntyre discuss the role of bacteria in acid formation and postulate the mechanism through which they operate. Mr. Ashmead in his discussion of my paper has assumed that this work was carried on in the presence of acid mine water in which bacteria would be present. This was not the case. Strictly sterile conditions were not maintained, but the organisms present in mine drainages were definitely absent in these experiments. We believe that we have demonstrated that alkalis do not inhibit the chemical oxidation of pyritic material. This is also indicated by Mr. Ashmead's discussion in which he says that alkali must be added daily due to the continuing chemical oxidation. It is interesting to note that Mr. Ashmead finds that maintenance of pH above 4.00 decreases the activity of the bacteria. We have found also that a decrease in pH below 2.8 also inhibits its activity. Table XIII of published data'" illustrates the decrease in activity with increased acidity, although pH values are not given. These values are in comparison with uninoculated controls and show the marked increase in acidity up to 22 weeks but a decline at 29 weeks, at which time the experiment was terminated. It is probable that after a longer period only chemical oxidation would have continued. From our studiesv we have postulated that the iron oxidizing bacterium (Ferrobacillus ferrooxidans) oxidizes the ferrous iron, resulting from chemical oxidation, to ferric iron. The ferric iron then aids the atmospheric oxidation of the sulfuritic material and is itself reduced to ferrous iron, which in turn acts as food for the autotrophic bacteria. Study of the physiologic properties of F. ferrooxidans shows that its preferred pH is about 3.00 and its activity decreases with variation in either direction. It is extremely inactive above pH 4.00 and below 2.5. This inactivity above 4.00 is indicated by Mr. Ashmead's observations. These properties of F. ferrooxidans then correlate perfectly with our hypothesis. Ferrous iron is oxidized very slowly by atmospheric oxygen in highly acid sohtion and since the bacteria become inactive, acid is formed only by atmospheric oxidation. At a pH of 4.00 or above iron is more readily oxidized by atmospheric oxygen, but the bacterial activity is decreased. However, with a pH above 4.00 the ferric iron is removed from the field of activity since its soluble sulfate hy-drolyzes and precipitates the iron as ferric hydroxide or a basic sulfate. As we have shown in the paper under discussion, the alkali does not inhibit the chemical oxidation, and thus the acid formation continues. This

Jan 1, 1957

By Emerson F. Heald

A systematic study was made of new and old data on chemical activities in Fe-Pt alloys at elevated ternperatuves. Experimental results may be expressed in terms of the excess free energy using Least-squares analysis of the data gave the following values for the constants: for the temperature range 1130° to 1350°C, and tentatively to 155O°C, B = -3.326564 and C = 0.221051; for the temperature range 650" to 850°C, B = -2.555690, C = 1.762735, and D =0.097196. In the study of iron-containing silicate systems, it is sometimes desirable to have a direct experimental measure of the activity of iron in the system. The well-known solubility of iron in platinum, often a headache in experimental work on iron compounds under reducing conditions, can be used to advantage in this respect. If the activity of iron in an Fe-Pt alloy in equilibrium with the silicate is known as a function of the composition of the alloy, chemical analysis of the alloy will give a knowledge of the activity of iron in all of the phases in the system. The present study was undertaken in order to elucidate the characteristics of Fe-Pt alloys as iron activity indicators. This work is intended to tie together some previous work, which may be summarized as follows. Larson and Chipman1 determined the activity of iron in Fe-Pt alloys at 1550°C by equilibrating platinum metal with calcium oxide-iron oxide-silica melts of known iron activity. Compositions of the resulting alloys were determined by chemical analysis. A similar study was carried out by Taylor and ~uan,' who worked at 1300°C. They brought the Fe-Pt alloys into equilibrium with iron oxide under conditions of known partial pressure of oxygen, and thus, from the work of Darken and ~urr~,~ conditions of known iron activity. Compositions were determined indirectly, by following the change in weight of the sample. Sundaresen et el* used the electromotive force of cells in which the alloy formed one electrode in order to measure the activity of iron in the alloy at 650" and 850°C. These temperatures were chosen to be above and below the first-order phase transition which takes place upon the ordering of Fe3Pt and the second-order transition which occurs upon the ordering of FePt3. EXPERIMENTAL 1) High Temperatures. The starting materials used were thin platinum foil, about 0.002 mm thick, and Fisher Certified reagent ferric oxide, Fez03, which had been heated for 24 hr at 1000°C. An intimate mixture of 80-mesh Fez03 and platinum platelets was placed in a thin platinum foil envelope. The latter was suspended from thin platinum wires in the hot zone of a vertical-tube, platinum-wound furnace of the type described by Muan and ~sborn.~ A capillary gas mixer similar to that used by Darken and Gurry3 was used to prepare a precisely known mixture of carbon dioxide and hydrogen, which was allowed to flow upward through the furnace tube. The partial pressure of oxygen in contact with the sample was thereby fixed at a value which was calculated from the charts prepared by porter? Temperatures were measured with a Pt-10 pct Rh-in-platinum thermocouple, which was calibrated using the melting points of gold (1062 .@C) and diopside, CaMgSizOB (1391.5"C). Temperature control was maintained to within i3"C with a Geophysical Laboratory proportional controller, using the furnace resistance as the sensing element. Samples were quenched by passing a small current through the platinum suspension wires, allowing the sample to drop into a bath of dibutyl phthalate at the bottom of the furnace tube. Prior to chemical analysis the samples were washed with acetone and dried. 2) Chemical Analysis. It proved possible, in almost all cases, to separate the Pt-Fe platelets physically from particles of iron oxide. The platelets were dissolved in a small volume of aqua regia, evaporated to dryness, and redissolved to 0.1 M HC1. In order to determine iron in the platinum alloy potentiometrically, it is necessary first to remove the platinum. A 10-cm column of Amberlite IR-120 cation exchange resin in the hydrogen form provided separation quickly and quantitatively: The mixture of iron and platinum in 0.1 M HC1 was added to the top of the column, and washed with about 100 ml of 0.1 M HC1. Under these conditions, the iron, principally in the form of cations such as FeC1" and FeCl;, is held quantitatively in the uppermost centimeter of the column. The platinum, in the form of anions such as PtC&- , is washed through without being adsorbed. After a qualitative test with stannous chloride indicated all of the platinum was removed, the iron was

Jan 1, 1968

[ ]

Jan 1, 1938

By R. W. Raymond

Under the names of Conservation, Social Justice, the New Nationalism, and Progressive Democracy, many earnest reformers are calling for a new system of Federal government to replace the one which they ascribe to our fathers, and declare to have been outgrown. They are proposing the lease by the United States of certain natural resources on the public domain, for the profit of the U. S. Treasury, instead of the sale of such resources to private citizens or associations of citizens. In the present paper, I shall try to show that this notion is neither new nor good. It is clear that the United States is owner, as well as sovereign, of public lands acquired through conquest or purchase from other nations, as it was owner of the public lands expressly ceded to it by the original thirteen States. Its policy with regard to such lands involves, therefore, two entirely distinct questions: What shall it do as owner ? and, What shall it do as sovereign ? The latter question, it must be confessed, has played but a small part in our history. All the prerogatives of sovereignty which were not explicitly conferred upon the Federal government by the original States were retained by them. The ownership or control of precious or other metals or minerals in the earth, for instance, was thus reserved to the several sovereign States. New York, South Carolina, and other States have passed laws on this subject, without regard to Federal authority. As new States have been successively admitted to the Union, the tacitly accepted theory has been, that they thereby acquired all the reserved rights of the original States. These newer States largely outnumber the first thirteen; and it is inconceivable that they would submit to any deprivation of sovereignty based on historical grounds. One of them—Texas—came into the Union by its own voluntary

Jan 1, 1913

By C. L. Sollenbeger, R. B. Greenwalt

PERHAPS the most widely used dispersants or gangue depressants in nonmetallic flotation are sodium silicates, which vary in silica-to-soda ratio from 1 to 3.75. Typical manufactured silicates in order of decreasing solubility and increasing amounts of silica are Metso, silica-to-soda ratio of 1.00; D, 2.00; RU, 2.40; K, 2.90; N, 3.22; and S-35, 3.75.* References in flotation literature1,2 to the use of sodium silicates are often weak because they fail to mention the type of silicate used. Metso and silicate N have occasionally been mentioned, but when the type of silicate is not mentioned, it is usually assumed to be N, the cheapest of the soluble silicates and the one recommended by sodium silicate manufacturers as a flotation agent. In the All is-Chalmers Research Laboratories a systematic study was made of the effect of different alkali-silica ratios on the concentration by flotation of two scheelite ores. One of these was a high grade ore from the Sang Dong mine in Korea. The effect of such factors as pH; addition agents; and conditioning time, temperature, and pulp density on the flotation efficiency of this ore have been described previously. The other ore was a low grade ore from Getchell Mines Inc., Nevada. The mineralogy and techniques of concentrating this ore have been described by Kunze. Hereafter these ores will be referred to as the Korean and Nevada ores. Experiments were made with both to determine the effect of three factors—-type of silicate, concentration of silicate, and pH of the pulp—on recovery and grade of tungsten in a rougher concentrate. Average WO, content of the Korean ore was 1.50 pct and of the Nevada ore 0.27 pct. The predominant tungsten mineral in both ores was scheelite, which was accompanied by a small amount of powellite. The powellite and scheelite were finely disseminated through both ores and required a —200 mesh grind for liberation. Major gangue minerals in the Korean ore, in decreasing order of abundance, were amphi-boles, quartz, biotite, garnet, fluorite, and calcite. Bulk sulfides composed about 3 pct of the total weight. Gangue in the Nevada ore, in descending order of abundance, was garnet, alpha quartz, calcite, phlogopite, wollastonite, and amphiboles. Sulfide minerals were 3 to 4 pct of total weight. Batch flotation experiments were made with 500-g samples of ore, each sample wet-ground to 90 pct passing 200 mesh. The finely ground ore was floated in a Fagergren batch cell at 25 pct solids. The natural pH of the Nevada ore was 8.9 and of the Korean ore, 8.5. The D, RU, K, N, and S-35 sodium silicates were obtained in colloidal dispersions with varying amounts of water. The most alkaline, Metso, was in dry powdered form. For convenience in addition, 5 pct solutions by weight were prepared from each of the silicates, on the basis of dry sodium silicate dissolved in the correct amount of distilled water. Chemical analyses of the various silicates are given in Table I, together with the pH of the 5 pct solutions. A preliminary bulk sulfide float was made with secondary butyl xanthate as the collector and pine oil as the frother. The WO] analysis of the sulfide concentrate was nearly 1 pct for the Korean ore and about 0.1 pct for the Nevada ore. The tungsten contained in the sulfide concentrate constituted about 3 pct of the total tungsten in each ore. No effort was made to recover these tungsten values. The scheelite was floated with oleic acid. Adjustments in pH were made with sulfuric acid or sodium carbonate. A 1 pct solution of 85 pct Aerosol OT was sprayed on the froth and sides of the cell during the scheelite float to aid in dispersing the minerals and to decrease the entrapment of gangue particles. Six tests were planned for each of the six types of silicate in which concentrations of 1, 2, and 4 1b of silicate per ton of dry ore were investigated at both 6.5 and 10 pH. All tests were made at room temperature. The performance of each silicate was judged from the grade and recovery of WO, in the scheelite rougher concentrate. Tungsten recovery was calculated on the basis of the scheelite remaining in the ore after the preliminary sulfide float. Testing of each silicate at three levels of concentration and two levels of pH required 36 tests with each scheelite ore. Variance analyses were performed on the concentrate grades and recoveries to determine whether or not the type of sodium silicate, the concentration of sodium silicate, or the pH significantly affected recovery or grade. Results Concentrate Grade: A variance analysis of the concentrate grades for the Korean ore showed that concentration of the silicate and pH of the ore pulp were major factors in producing a high grade concentrate. Also, the silica- to-so da ratio was important as an interaction with pH. The concentrate grade vs silica-to-soda ratio is plotted in Fig. 1. The curves show that the concentrate grade improved with an increase in concentration of sodium silicate and also

Jan 1, 1959

By R. L. Stephenson

The effect of fabrication variables on the creep-rupture properties of TZM (Mo-0.5 pct Ti-0.08 pct Zr-0.03 pct C), Cb-TZM [columbium-modified TZM (7140-1.5 pct Nb-0.5 pct Ti-0.8 pct Zr-0.05 pct C)], and TZC (Mo-1.2 pct Ti-0.25 pct Zr-0.15 pct C) has been studied at 982º. 1093º, 1204º, and 1315°C for rupture times up to 1000 hr. The creep tests were performed in vacuum creep furnaces, employing cold-trapped oil-diffusion pumps, operating at pressures 2 X 10-7 tory. After-test chemical analyses showed no significant changes in interstitial content. The creep-rupture properties of TZM, fabricated according to current mill practice, were determined in the stress-relieved and in the re crystallized conditions to provide control data. Specimens of TZM, Cb-TZM, and TZC fabricated according to each of two experimental fabrication schedules were then tested. The schedules differed in terms of in-process annealing temperatures and warm -working temperatures. The data make several conclusions evident. Fabrication variables do indeed have a profound effect on the long-time creep-rupture properties of molybdenum alloys. Strengths of these alloys compare very favorably with those of other refractory metal alloys in the temperature range studied. FOR several years we have been engaged in the evaluation of the creep-rupture properties of promising refractory metal alloys. We consider the determination of these properties to 1000 hr at several temperatures necessary for a valid comparison. Such an evaluation indicated that the creep strengths of Mo-0.5 pct Ti and TZM (Mo-0.5 pct Ti-0.08 pct Zr-0.03 pct C) compare favorably with those of other refractory metal alloys. Tensile and recrystallization data of other investigators1,2 show an effect of fabrication variables. More specifically, those fabrication schedules which produce high strength through work hardening exhibit the least thermal stability. A similar conclusion was reported by perkins3 for Cb-TZM. This would lead one to expect that, in terms of creep, those materials showing higher strength at short times and low temperatures would exhibit lower strength at long times and high temperatures. If these expectations were fact, a substantial improvement could be made in these alloys by optimizing their fabrication schedule in terms of their anticipated service temperature. We therefore undertook a study of the effect of fabrication variables on the long-time creep properties of TZM, Cb-TZM (Mo-1.5 pct Cb-0.5 pct Ti-0.08 pct Zr-0.05pct C) and TZC (Mo-1.2 pct Ti-0.25 pct Zr-0.15 pct C). MATERIALS All materials used were supplied by the Climax Molybdenum Co. of Mich. Our original intention was to test the same heat of each alloy in different conditions. Fabrication difficulties prevented this; however, heats with nearly identical analysis were selected. The compositions of the materials used are listed in Table I. All materials were supplied in the

Jan 1, 1970

By William P. Blake

In directing attention to the newly-opened zinc-ore region in Southwestern New Mexico, I adopt a suggestion made at the Engi neering Congress last summer in Chicago by Prof. Le Neve Foster, who commended the indication of the geographical position of a district under description by means of an outline-map. Such a map is the more important in this instance, inasmuch as the region to be described is remote and little known even in the United States. Until within a few years it has been infested by the savage Apaches, has not been often visited by mining engineers, and could not be

Jan 1, 1895

By J. R. Cahoon, H. W. Paxton

The possibility of using unidirectionally solidified, two-phase alloys as an approximation to fiber composite materials is investigated. The short-term me.chanical properties and failure modes of unidirectionully solidified A1 (rich)-Cu alloys containing ap -Proximately 0, 17.5, and 27.7 vol pct of 0 phase 'fibers" are determined at temperatures from 25" to 500" and compared with those obtained for conventionul SAP alloys. In a previous publication,' hereafter referred to as I, the possibility of understanding some of the room-temperature mechanical properties of unidirectionally solidified castings was explored. For Al(rich)-Cu and Al(rich)-Mg two-phase alloys over a substantial range of compositions, the yield and ultimate strengths and common ductility measures were very adequately predicted from the principles of fiber strengthening4 and the analysis of ductility outlined by Gurland and Plateau." The results obtained in I suggest the possibility of using unidirectionally solidified, two-phase alloys to simulate fiber composite materials where the inter-dendritic second phase or constituent acts as the reinforcing material. Recent attempts concerning the fabrication of fiber conlposites have concentrated on producing composites with a good bond between fiber and matrix and with very long fibers so that their maximum contribution to the strength of the composite may be realized. However, these objectives are difficult to attain in practice and present fabrication processes are either extremely laborious or costly.13 The slow, unidirectional solidification of eutectics has received considerable attention as a method for producing composite materials. 5,6 This method can fulfill both of the above objectives but it is currently laborious, expensive, and has the additional disadvantage that the volume fraction of reinforcing phase cannot be easily varied. On the other hand, unidirectionally solidified, two-phase alloys, also with a good bond between the phases, are relatively easy to make and the volume fraction of reinforcing "fibers" can be easily varied by changing the average composition of the alloy. The disadvantage of the cast alloys is that the mechanical effectiveness of the "elongated interdendritic reinforcements" (EIR)* may be reduced due to their rela- tively short lengths, the w factor in Eq. [2] of I. However, if the EIR have a high strength their contribution can be considerable. For composite materials containing discontinuous cylindrical fibers of various lengths the ultimate strength is given by1 where it is assumed that the composite fractures when the fibers fail. In Eq. [I], a, is the stress in the matrix just prior to failure of the composite, Vf is the total volume fraction of fiber reinforcing constituent, Vf(l+) is the volume fraction of fibers whose lengths exceed the critical length, I,, which is defined as the shortest length of fiber in which the stress can build up sufficiently to break the fiber. af is the fracture strength of the fiber material, w is a factor accounting for the discontinuity of those fibers whose lengths exceed I,, 1-/d is the average aspect ratio of those fibers whose lengths are shorter than I,, and t is the shear stress in the matrix at the fiber-matrix interface. The factor w is dependent on the length of the fibers and also on whether deformation of the matrix occurs plastically or elastically. However, for a given length of fiber, w is smaller when elastic deformation of the matrix is assumed.' It is of interest to consider the properties of simple unidirectionally solidified, two-phase alloys at elevated temperatures in view of the possibility of using suitable modifications for high temperature service. Knowledge of the creep behavior of these materials is still rudimentary (although under active investigation) and the present paper concerns itself with short time tensile properties of some alloys similar to those investigated in I (i.e., unidirectionally solidified Al(rich)-Cu alloys). Unidirectionally solidified alloys containing 5.6, 17, and 23 wt pct Cu were tested parallel to the direction of solidification at temperatures from 25" to 500°C. In the present investigation, the alloys were homogenized for 2 days at 535°C giving a matrix of homogeneous a phase (5.2 wt pct Cu) and an interdendritic constituent (EIR) which was completely Q phase (53 wt pct Cu). EXPERIMENTAL Alloys of nominal composition 5.6, 17, and 23 wt pct Cu (containing approximately 0, 17.5, and 27.7 vol pct 8 phase, respectively, after homogenization at 535°C) were prepared by melting 1200 g of A1 (99.99 pct) in a high purity graphite crucible and adding the appropriate amount of freshly cleaned copper chips (99.9 pct). The molten alloy (at 700°C) was poured into a preheated graphite mold (also at 700°C) and the ingot unidirectionally solidified by impinging water on the steel baseplate of the mold. The alloy was degassed immediately

Jan 1, 1970

By F. A. Emmerton

I have used for about two years, in the laboratory of the Joliet Steel Company, a rapid method for the determination of phosphorus in iron, steel, and ores, which possesses one or two features sufficiently novel to warrant description. In general, it is the method described by Mr. Benjamin B. Wright (Transactions, vol. x., p. 197), involving the precipitation of the phosphorus by means of molybdate solution, and its estimation in the yellow precipitate by reduction of the molybdic acid, and titration of the resulting oxide with a standardized permanganate solution, according to the principles laid down by Werncke (Fres, Zeit., vol. xiv., p. 1). In the use of this method, I had difficulty at first in obtaining a yellow precipitate of reasonably uniform composition. It is a well-known fact that, to secure this result, the conditions of precipitation must not vary. The principal condition is temperature; and acidity, concentration, proportion of nitrates and chlorides, and time, are important elements. I am aware that uniformity in these conditions has been obtained to a reasonable extent by many chemists,. so that they are enabled to use with success, methods based on the

Jan 1, 1887

By William Marsh Baldwin

TWO of the most useful and important equations available to the metallurgist for the study of plastic deformation of metals are the Huber-von Mises-Henckyl-~ and the St. Venant7-10 equations. Huber-von Mises-Hengky Equation The Huber-von Mises-Hencky equation answers the question: When does plastic flow occur in metal that is subjected to a multi-axial stress? It occurs, according to this equation, when the three principal stresses,t UI, u2, and u3 satisfy the equation: (<ri - <r2)2 + (<r2 - <rsY + (ff! - <r3)* = 2Ki [i] Here K is the yield strength of the material as determined in an ordinary tensile test. If the quantities ul, 52, andas are assigned to the coordinates of a Cartesian three-dimensional system, this expression describes a cylinder whose axis of symmetry is inclined at equal angles to the three coordinate axes4s6 (Fig. I). The radius of this cylinder is .\/%K. For the purpose of simplicity, it is sometimes advantageous to ascribe the values al/K = sl, az/K = s2, UD/K = SJ to the three coordinate axes instead of the principal stress alone. In this case, Eq. I becomes (*i - s*)1 + (s2 - S3)2 + (si - SiY = 2 [2] and the radius of the cylinder becomes \/%. In the latter method of representation, a point lying inside the cylinder indicates that the metal will react elasti-cally, whereas a point lying on the cylindrical surface indicates that the metal will behave plastically. Some of the geometric features of this cylinder are worthy of study. Let us inquire first as to what interpretation may be placed upon what we will choose to call the "circles of latitude" of the cylinder (L in Fig. I) and the "meridians" of the cylinder (M in Fig. I). Circles of Latitude Circles of latitude are formed by allowing a plane, passing perpendicular to the cylinder axis, to intersect with the cylinder. Any point, P, on this circle is presumed to have the coordinates sl, SZ, and s3. The coordinates of the point resulting from the intersection of the plane and the cylinder axis will be a, a, and a (since the cylinder axis is equally inclined to the three coordinate axes). L?t US now pass a line through the point on the circle and the point on the axis.

Jan 1, 1946

By R. D. Saltsman

This paper deals with the evolution of a test procedure devised to totalize a coal&apos;s ignitibility, its degree of caking, and its coke reactivity and the development of a method for assigning proper combustion indices to stoker coals. The application of this type of work to stoker design is also discussed. It is believed that this work may be the prelude to understanding the effect of various petrographic constituents on the combustion characteristics of a coal or a blend of coals. The inadequacy of our knowledge of the coal combustion process has long been recognized. This was expressed very well by Spicer and Finney.1 "The control of combustion processes in industry and the design of the equipment necessary for efficient burning to take place have always been very much branches of an industrial art rather than of an exact science. This has been especially true of the utilization of coal, a substance so heterogeneous and complex in character that all too little is known about its chemical and physical composition." During the past several years one branch of coal utilization, that of high temperature carbonization, has made significant advances from being an art into being an exact science. This has been accomplished by the development of petrographic techniques for identifying, measuring, and determining the thermal properties of the organic materials which affect the carbonization of coal and the correlation of this information with a pre-existing standard of coke quality, the stability index. The success in using petrographic analysis for predicting the coking properties of coals and their blends suggested that petrographic techniques might be applied to the combustion process for predicting the combustion characteristics of coals. Certainly the different organic entities2 influence the combustion characteristics of a coal as they influence its coking properties. If it were possible to predict combustion characteristics from an analysis of a coal&apos;s petrographic composition, it would seem logical that an intelligent investigation could then be made into methods of altering stoker coals to improve their combustion characteristics. The successful application of petrographic analysis in the field of high temperature carbonization was made possible by the pre-existence of the stability index, which is a numerical value of coke quality. The quality of combustion is determined by the sum of the effects of the ignitibility, the caking, and the coke reactivity characteristics of a coal. While the literature is filled with papers reporting the correlation of various analyses to the ignitibility, or to the caking, or to the coke reactivity characteristics of coals, none of these earlier studies could be related to one index. The lack of a single index for combustion quality precluded the application of petrographic techniques for predicting combustion characteristics. SELECTION OF THE COMBUSTION TEST EQUIPMENT The primary prerequisite of any test developed to evaluate the relative performance of stoker coals must reflect the three characteristics of the coal burning process: 1) ignitibility, 2) degree of caking, and 3) coke reactivity. The widespread variations in these combustion characteristics of the available stoker coals are well known. The ignitibility, which has been defined as that characteristic which determines the ease with which the fuel may be brought to a condition of self-supporting active oxidation, varies from where a coal is deemed to be flashy to the opposite extreme of being fireproof. The ignitibility of a coal influences its ability to pick-up from hold fire, greatly affects the degree of bed stability during swing loads, and is a factor in determining the average burning rate obtainable on a given grate. The caking characteristic affects the degree of bed porosity during the devolatilization period, and coals are classified on a scale varying from free burning to highly caking. Caking is not synonymous with bed swelling since a bed may swell two to three times its normal depth during the period of devolatilization yet remain very porous, allowing an efficient and high rate of combustion to take place. Caking is melting

Jan 1, 1964

By E. J. Dulis, V. K. Chandhok, J. P. Hirth

Cobalt clearly increased the activity of carbon in austenite and in ferrite. This effect of cobalt on carbon activity Plausibly accounted for the effect of cobalt on accelerating the austenite to pearlite transformation. Cobalt was found to have only a slight effect on carbon diffisivity in various Fe-Co and Fe-Co-W-Mo austenites, but was found to decrease carbon diffusivity in Fe-Co ferrite. THE effect of cobalt in steel is unique in that it is the only element that reduces hardenability by accelerating the austenite to pearlite reaction. The results of several excellent investigations aimed at explaining the role of cobalt have been published,1"7 but a complete understanding is still lacking. In addition, cobalt significantly enhances the resistance to softening or tempering of highly alloyed highspeed and hot-work tool steels. The resistance to tempering is related to the secondary hardening reactions associated with the fourth stage of tempering during which carbides of molybdenum, tungsten, and/or vanadium form in a martensite matrix. The effect of cobalt on secondary hardening reactions in high-alloy tool steel has received considerable attention, but a full explanation of the reactions involved has not been developed. Inasmuch as austenite to pearlite transformation and secondary hardening involve carbide formation, the present authors believed that the role of cobalt in effecting carbon activity and diffusivity in austenite and in ferrite was important to a fuller understanding of the phenomena involved. TO investigate the effect of cobalt on the activity coefficient of carbon in austenite, an approach was used similar to that used by Darken17 in his experiments on the effect of silicon, manganese, and molybdenum on carbon activity and diffusivity in austenite. TO

Jan 1, 1962

By Parke A. Dickey, Robert B. Bossler

The presence of connate water in oil sands is of far greater practical significance in secondary oil-recovery operations than it is in primary operations. The percentage saturations of oil, water, and gas in a depleted field determine whether it will be economically possible to recover oil by secondary methods, and whether water-flooding or gas-driving, or either, will be successful. It is suggested that economic recovery of oil by secondary water-flooding can occur only when a rich bank of oil is formed by the encroachingm water. If the sand has a greater effective permeability to water than it has to oil before flooding, a bank will not be formed, and water-flooding will not be successful, although gas-driving may be. Published results of laboratory work indicate that the effective permeability of a sand to oil and water depends primarily on the saturation of the sand by these phases. They also indicate that a small difference in relative saturation produces a large difference in effective permeability to the phase in question. There thus exists a critical range of saturations, wherein a small change in oil and water content of the sands will make water-flooding possible or impossible. In gas-drive operations the water saturation is less critical but no less important. The presence of connate water in a sand increases the proportion of the residual oil that may be recovered by gas drive. Sands containing oil saturations too low and water saturations too high to make water-flooding possible can often be subjected to gas drive with economic recovery of oil. The results of laboratory work on test samples that do not contain water cannot be applied to normal field operations. More tests on cores containing water as well as oil are desirable, and the improvement of coring technique is necessary. However, sufficient data are already available to enable an operator to use core data intelligently in estimating the chances of a secondary oil-recovery program. Introduction In recent years laboratory work has led to a much better understanding of the principles of oil-reservoir performance. The general principles of the expulsion of oil from sandstone by gas or water were developed by geologists of the Second Geological Survey of Pennsylvania in the 1870lsl but only recently has the mechanism of gas or water drive been intensively investigated. Most published articles have large the facts established in the labora tory to the primary production of oil from flush fields- This Paper is not based on any new observations, but is an attempt to apply some of the conclusions obtained in the laboratory and described in the literature to the recovery of oil from depleted pools by secondary methods. One of the most important factors that determine whether or not a secondary-recovery operation is economically successful is the ratio of injected fluid to oil recovered. This ratio may be expressed as the over-all or cumulative gas-oil ratio if gas is the driving medium, or water-oil ratio if water is the driving medium. Recent theoretical and experimental work has shown that the relative amounts of

Jan 1, 1944

By John Blatchford, H. O. Hofman

The leading antimony mineral is stibnite. In smelting stibnite ore two processes are available, precipitation and roasting-reduction. The former is suited only for high-grade ores. As low-grade ores are more common than high-grade, roasting-reduction is of greater importance than precipitation. In the roasting process the aim may be to leave the oxidized antimony in the ore, or it may be to volatilize as much of the antimony as possible, collect the volatilized oxide as a rich intermediary product and smelt it for antimony, leaving the gangue poor enough to be considered a waste product. Whichever way the roast is conducted certain difficulties inherent in stibnite are encountered. These are: 1. The low melting point of stibnite which, according to Pélabon,&apos; is 550°C., according to Wagemann2 540°C., and according to Borgstroma 546°C. 2. The ignition temperature: According to Friedrich,4 stibnite, if heated in air, begins to oxidize at 290°C. if the size of a grain is 0.1 mm. in diameter; at 343", if 0.1 to 0.2 mm.; and 430" if 0.2 mm. 3. The fusibility of a mixture of Sb2S33 and Sb203 which in the form of kermesite (Sb2S3)z.Sbz03 melts at 517°C.6 4. The volatility of Sb2Ss and SbzOs, for which no numerical data appear to exist, although practical experience has shown that they are volatile at low temperatures. As regards the oxidation of metallic antimony, we have the experimental evidence of C. F. Plattner6 that when fused and brought to a red heat, it burns with a bluish-white flame to Sb2Oa which passes off as a

Jan 1, 1916

CHARLES CATLETT, Staunton, Va. (communication to the Secretary*). -I hesitate to discuss in general terms a paper such as Mr. Wysor&apos;s, which bears evidence of so much careful and detailed investigation, yet it is the broad possibilities which his paper presents that are really attractive and his cautious conservatism may make us unappreciative of these possibilities. Mr. Wysor calls attention to the fact that the iron-ore mixture which he uses, carrying 0.28 per cent. of potash, is probably above the average. No doubt this is true, but on the other hand it may be very much less than the mixture at some blast furnaces or very much less than would be the case with special mixtures bearing the question of potash in mind. Unfortunately, iron ores are not ordinarily examined for potash, and with the ordinary analyst there is opportunity for very considerable error in the determination. The 10th Census gives 270 complete analyses of iron ore, on the accuracy of which we may rely. Of these, there are 21, or 8 per cent., that carry more potash than Mr. Wysor&apos;s mixture; 14 of these carry approximately twice as much, or more; eight carry approximately three times as much, or more; three carry approximately five times as much; one carries over seven times as much. It may be worth while to take some of the ores that are known to be high in potash and consider the possibilities in the light of Mr. Wysor&apos;s investigations.

Jan 5, 1917