Search Documents

By I. Iwasaki, R. Titi-Manyaka

Chlorination and chloridization behaviors of pyrite, pyrrhotite, marcasite, chalcocite, covellite, galena, sphalerite, heazlewoodite, and elemental sulfur were investigated by thermogravimetric analysis. The possible reaction mechanisms are discussed on the basis of the theoretical weight changes and thermodynamic considerations. Chlorine is a more effective chloridizing agent than hydrogen chloride. In the light of the experimental results, a scheme for producing nonferrous metal chlorides, molten sulfur, and ferric oxide from complex sulfide flotation concentrates is discussed.

Jan 1, 1974

By F. B. Plummer

THE practice of introducing acid into oil wells to increase production of oil and gas has been in use since 1894, when it was first used in the Pennsylvania. oil fields30.? It is only since 1928 that it has been used to any extent in the Mid-Continent18. The process has proved successful in increasing production, at least temporarily, in depleted oil fields where the producing formation is highly calcareous and where water drive is not too pronounced. In the Zwolle field in Louisiana, where the producing horizon is a chalk, increases of 100 per cent have been recorded25. In north-central Texas, where the oil is produced from the Marble Falls limestone, equally pronounced increases have resulted3. The production also in some fields yielding oil from quartz sand cemented with calcite has been benefited. The evidence of actual increase in total recovery of oil, however, has been questioned by some engineers18. It has been pointed out that the results of the treatment of a well in a new district, where the process has never been tried out, can never be predicted with certainty, since other factors besides percentage of calcareous content: of the oil sand play a large part in determining the success of the method. Numerous articles have been published on acid treatment and on the effects of acid on limestone1-35, yet very little has been written con-cerning experimental work on the actual effect, of acid on capillary pores and larger oil-coated voids of oil sands. This is due partly to difficulties in duplicating field conditions in a laboratory and partly to the fact that the process has been carried out largely by contracting companies that have been unwilling to publish details of their results for fear of loss of business to competitors. The authors, using equipment developed to measure the radial permeability of oil-sand cores29, have developed a method of investigating the results of acid treatment which has enabled

Jan 1, 1935

By W. L. Phillips

Stress-strain data are reported for sodium chloride, lithium fluoride, and magnesium oxide tested in compression at diffevent strain rates in the telrlperature range from 70° to 873°K. Quantitative equations are given for the stvain-rate dependence of the critical resolved shear stress and the initial rate of work havdening. The properties so determined are compared with results previously reported for metals. ALTHOUGH the effects of strain rate and temperature on the stress-strain characteristics of metals have been extensively investigated1,2 these effects have not been studied in detail in ionic crystals. In the only previous investigations on the effect of strain rate on the deformation of ionic crystals. Gilman and gohnston3 and Hulse and pask4 have shown that the yield stress of lithium fluoride and magnesium oxide at room temperature is proportional to the ninth or tenth root of the strain rate. CRYSTAL PREPARATION Lithium fluoride, sodium chloride. and magnesium oxide single crystals were purchased from the Har-shaw Chemical Co. The compression fixture and sample preparation have been described in detail previously.5 The detectable impurities in MgO were eight parts in 105 of Fe and six parts in 105 of Si; in LiF, six parts in 105 of Mg; and in NaC1, two parts in 105 of Fe and four parts in 10&apos; of Mg. The cleaved samples measured - 0.1 in. by 0.1 in. by 0.3 in. Prior to testing all samples were annealed at -0.8 of their melting point and cooled to room tempera- ture at 50 C per hr.&apos; Samples were strained at rates (<) of 0.1, 0.01, 0.002, and 0.0002 in. per in. per min. EXPERIMENTAL RESULTS Fig. 1 is a plot of the critical resolved shear stress a,. (extrapolation of slope of easy glide region to zero strain) of sodium chloride, lithium fluoride, and magnesium oxide tested at different strain rates as a function of temperature. In all crystals at all strain rates a, decreases with increasing temperature according to an equation of the type397 where uo is a stress constant, K is a constant, and T is the absolute temperature. The points in Fig. 1 are the average of six tests. It is evident that there is a break in the log 0,- temperature plots at a characteristic temperature T,. The constant K of Eq. [I] is dependent on strain rate, Fig. 2. The relationship

Jan 1, 1962

The object of crushing and grinding for leaching is obviously to permit contact of the solvent and mineral and subsequent removal of pregnant solution in a reasonable time. Heap leaching is the leaching of ores that have been mined and transported to prepared, relatively impervious pads for leaching by sprinkling or ponding, and percolation of the lixiviate through the ore. Dump leaching is the leaching of dumps or low-grade ore or overburden without the use of prepared pads under them. Run-of-mine material, e. g., low -grade ore from open pit stripping operations, may be leached without crushing, and a fairly high recovery made by heap leaching. An alternate method for better grade gold/silver ores is to crush to 9 to 13 mm (318 to112 in. ) size for pad heap leaching, as used by Smoky Valley Mining Company at Round Mountain, Nevada, on gold ore, and to 38 rnrn (1 -1 12 in.), which will be done by Candelaria Partners, at Candelaria, Nevada, on silver ore. Heap leaching of copper probably began at Rio Tinto, Spain, about the year 1752. This was done by the leaching of weathering piles of ore in the open air followed by iron cementation of the liquor that drained off the heaps. Its application to the low -grade southwestern United States copper ores was overlooked for many years, and low- grade ores from Sacramento Hill at Bisbee, Arizona, were the first to be heap leached in 1923. Site preparation used a half century ago is the same today. "The need for some form of waterproofing of the pad was evident. Before leaching ore was piled, the site was cleared of cactus and brush. After clearing a gentle sloping area, it was then covered with a blanket of rolled and tamped clay or slime tailing. When heaps are built, a layer of coarse fragments may be put down first to assist drainage. A second method of leaching without grinding, usually for higher grade ores, is by vat or tank leaching of material crushed to 9 to 13 mm (318 to 112 in.) size. Such a plant is considerably more expensive than a heap leaching installation but much less costly than grinding for agitation leaching, and a recovery higher than that obtained by heap leaching is to be expected. Vat leaching has been widely used by the copper industry on higher grade copper ores but has been used in only a few small operations on that size gold or silver ores. However, such a plant should be considered for a modest tonnage of a few million tons, 3 to 7 g per mt (0.10 to 0.20 oz per st), of Carlin-type leachable ores crushed to 9 mm (318 in.).

Jan 1, 1981

By W. E. C. A. B. Eustis

(Read at the Philadelphia Meeting, February, 1878.) IN September last I had my attention called by Mr. R. G. Leckie to a deposit of nickel in the township of Orford, province of Quebec. In many ways it has proved to be a subject of great interest. As this ore is, as far as I can learn, entirely new in mineralogy and metallurgy, it has seemed to me that it would be a matter of interest to the Institute to have laid before it, in a short paper, the peculiarities I have met with in studying it. This deposit of nickel was first described by Dr. T. Sterry Hunt, our President, in the Geology of Canada, 1863, p. 738, in the following terms : "The general diffusion of nickel throughout the magnesian rocks of the Quebec group has been already noticed. It has, however, never been met with in any considerable quantities in these rocks, although workable deposits of its ores may reasonably be looked for

Jan 1, 1878

By M. S. Smani, P. Blazy, J. M. Cases

Investigations on the beneficiation of sedimentary Moroccan phosphate ores are reported in four separate parts. The first discusses electrochemical phenomena at the solid-aqueous solution interface for minerals of the apatite group. In the second part, the electrochemical properties of the calcareous gangue associated with the phosphate ore are investigated. The flotation of calcite and phosphate oölites, using both anionic and cationic collectors, is discussed in the third part. It is shown that selective recovery could be obtained for precise concentrations of collectors and pH ranges. Results of work aimed at optimizing depression of phosphate oölites during inverse flotation of the carbonate gangue with sodium oleate are reported in Part 4.

Jan 1, 1976

By Peter Joralemon

Peter Joralemon&apos;s contention that Nevada contains one of the world&apos;s major gold belts is the result of 30 years&apos; active involvement with the state&apos;s regional geology. He first suggested the possibility of an arsenical gold belt-tenuously based on two replacement deposits 480 km (300 miles) apart-in his 1949 doctoral thesis of the Getchell mine. In the years that followed, some 18 or 20 arsenical gold ore bodies have been discovered along the lineament Joralemon postulated. In this article, he uses the evidence that he&apos;s collected over the last three decades to refine his 1949 thesis. Joralemon&apos;s conclusion: A mineral belt containing a billion dollars worth of gold extends the length of Nevada, and a number of ore bodies are yet to be discovered.

Jan 7, 1978

By Arthur W. Rose

Statistical techniques are being widely used in geochemical exploration to answer questions involving sample spacing, analytical and sampling errors, thresholds, data smoothing, and optimum combination of several elements into one measure of favorability. The applications of sampling theory, mean and standard deviation, trend surfaces, moving averages, factor analysis, cluster analysis, discriminant analysis, and regression analysis to these questions are discussed with examples. Although the techniques are very useful as means of handling large amounts of data, they require as much geological and geochemical judgment as any other approach to data interpretation.

Jan 1, 1973

By J. A. Clum, R. W. Heins, T. D. Tiemann

The use of Na-montmorillonite clay hinders (Western Bentonite) in the pelletizing of iron ore concentrates is well established as is the idea that alternative binders must be found. 1-6 This note summarizes work done7 in evaluating a Wisconsin montmorillonite clay binder. The clay occurs in irregualr beds overlying the Prairie du Chien Dolomite and the St. Peters Sandstone near Hersey, St. Croix County. The raw Wisconsin clay contained 65% quartz and 35% clay minerals. The Na20to CaO ratio was 0.234. Suspension viscosity tests of the raw clay gave results only slightly better than water alone, even after treatment with activator materials. Sedimentation treatment reduced the quartz in the decantate to 5% after 240 min (four hours). Twenty minutes of sedimentation produced a decantate with 27.5% quartz which was found as effective as the 5% quartz decantate in pelletizing behavior. The 20 min decantate was used in subsequent tests. The decantate was filtered and dried at 110°(230°F). The minus 200 mesh portion of this was added directly to the magnetite concentrate. Pellets were made in a laboratory sized disc pelletizer from pastes consisting of ore concentrate, balling water (9%) and binder (clay, or clay + resins, or resins). The pastes were premixed in a Waring blender. The binders were: (1) 1% of a commercially used Western Bentonite; (2) 1 % or 3% of the Wisconsin clay (raw, or 20 min decantate); (3) 20 min decantate washed with activator solutions, (to exchange Na for Ca in the clay); (4) decantate with activator added in the balling water; (5) decantate with organic resins; (6) organic resins. Measurements of the 0.46 m (18 in.) Green Drop Number, the Dry Strength and the Fired Strength (fired at 1260°C (2300°F) for 30 min) were made. The dry and fired compressive strengths were determined on an Instron testing machine using a C-load cell and a F-load cell, respectively. The cross-head speed was 0.004 m/sec (0.1 in./min) for both. The results of each measurement were averaged for 15 pellets. A summary of those results is presented in [Table 1]. More detailed results and procedures are presented in another report.7 In addition to the effects on pellet strength due to various binders the effect of varying magnetite concentrate characteristics is noted in [Table l]. There, a few comparative data are shown for Cornwall, PA Magnetite, which has a generally liner particle size than the Black River Falls magnetite which was used for most of the tests.

Jan 1, 1979

Jan 1, 1944

By R. J. Towner

Tensile properties of Aluminum Powder Metallurgy (APM) products at 600°, 800°, and 1000°F were lowered by cold reductions of as little as 10 or 20 pct. The detrimental effect of cold work on yield strength at elevated temperatures increased with temperature. Heating cold-worked products at 850° to 1150°F removed the structural effects of cold work through the process of recovery and restored, at least partially, the strength at 600°F to the level of hot-worked material. Material containing 5 pct A1203 was recrystallized by cold reductions of 97 pct or more followed by annealing at 1100°F. Recrystallization lowered sharply the strength at room temperature, but raised the strength at 600°and 800°F relative to that of the cold-worked state The high strength of Aluminum Powder Metallurgy (APM) products at elevated temperatures&apos;-4 is well-known. In this paper, some conditions of processing that can affect this important characteristic are presented. The following nomenclature will be used to identify different alloys: All of the above alloys are of the aluminum-aluminum oxide type made from milled powders of commercially pure aluminum with the exception of M486, which is fabricated from atomized A1-Fe alloy powder. The products made from milled powders are hardened by a dispersion of aluminum oxide par- ticles in the aluminum matrix, while the intermetal-lic compound FeAL is the dispersion hardening agent in M 486.&apos; The process used for making all APM products involves the application of heat and pressure to form a compact from powder which is fabricated into an extrusion, sheet, strip, or wire by standard techniques. Probably the most common cold-worked APM product is sheet. Cremens, Bryan, and rant&apos; determined the room-temperature tensile properties and the 600°F stress-rupture properties of XAPOOl and XAPOO3 sheet and reported that there was little difference between the as-extruded, cold-worked, and annealed at 1200°F conditions. On the other hand, Emmons6" found that the tensile and stress-rupture properties of XAPOOl and XAPOO3 sheet at 600" and 800°F were lower than those of extrusions. The tensile properties of XAPOO3 sheet were also determined at elevated temperatures by Doyle&apos; and ~ayward.&apos; According to Friske" and Kendal et a1.," cold working by swaging, rolling, and tube drawing reduced the tensile and creep-rupture strength of XAP 001 Recrystallized aluminum powder metallurgy products are rare because the dispersion in the aluminum matrix is usually too fine, uniform, and concentrated to permit recrystallization. However, Lenel12 was able to recrystallize wires made from aluminum powders containing about 1.75 and 3.0 pct oxide and found that the tensile properties at room temperature remained higher than those of annealed commercially pure aluminum because of the dispersed oxide particles. Westerman and Lenel13 found the kinetics of recrystallization of the powder products were very different from those of cold-drawn commercially pure aluminum wire. The alloy containing 3.0 pct oxide recrystallized to a very coarse grain size was more creep-resistant at 400" to 600°C (752" to 1112°F) than in the as-extruded, fine-grained condition, according to Ansell and weertman.14 Ansell and aenel" further studied creep at 500" to 620°C (932" to 1148°F) of recrystallized 1.75 pct oxide wire and confirmed the creep model of Ansell and Weertman. The present work is being reported for the fulfillment of the following objectives: 1) to show the effect of cold work on tensile properties at elevated temperatures;

Jan 1, 1964

By R. R. Morral, F. M. Krill, K. T. Aust

THE occurrence of twins in aluminum ingots cast under certain conditions has been well established. For instance, Herenguel and Lacombe1,2 have observed a twinned columnar structure in 99.5 and 99.9 pct Al, solidified by continuous or semicontinuous casting. The structure, which they termed "basaltic," appears in the form of elongated crystalline fibers of alternating luster. Herenguel and Lacombe2 found sections of flat crystalline plates composed of twin crystal plates, in which the twin plane (111) and a [I121 direction contained in the twin plane are parallel to the principal heat gradient. This orientation relationship is different from the usual orientation texture observed in cast face-centered cubic metals, where the [100] direction is approximately parallel to the long columnar axes lying in the direction of growth." A large amount of twinning has also been observed by the present authors in semicontinuous cast aluminum of 99.2 pct purity, Fig. 1. Mondolfo4 has suggested that the twinned cast structure forms by a deformation twinning process as the result of uneven cooling stresses within the ingots. This suggestion appears to be inconsistent with the large amount of twinning observed in the semicontinuous cast ingots and with the large difference of dendritic

Jan 1, 1953

By C. N. Schuette

The material presented in this paper has been gathered by the writer during a long and varied experience on matters pertaining to the quicksilver industry. During the past 18 years he has visited practically all of the quicksilver mines of the United States and has had occasion to review the literature on quicksilver mining the world over. In a previous publication1 the conclusion was expressed "that the greatest opportunity for increasing the economy in quicksilver production lies in giving more attention to the geology of the deposits ... " The present paper is a contribution toward that end. Due to a lack of correlation of the observed facts, a great deal of confusion exists in the views of various writers concerning the mode of occurrence of quicksilver ores. This paper attempts to show that certain common factors underlie the formation of all quicksilver orebodies. It attempts to present a framework on which to marshall the observed facts and thus make clear the interrelation of various observations which at first sight appear to be contradictory. The material presented is fragmentary in many respects and it is hoped that readers familiar with the deposits mentioned may supply the deficiency. The reader is asked to refer to the publications cited for maps and additional information on the individual orebodies, as this review, in covering so much territory, must necessarily confine itself to a bare outline of the facts concerning each occurrence. The writer hopes that this paper will elicit comment and criticism from the many competent men interested in the quicksilver industry and to all of them he would express his indebtedness for the many courtesies that they have extended to him at various times in the past. Theory op Primary Concentration The mode of occurrence of any given orebody presents an individual problem to the miner engaged in exploiting it. No two orebodies are exactly alike in their geological relationships, therefore an understanding, in detail, of the geology is necessary if the orebody is to be exploited in the most economic manner.

Jan 1, 1931

By Andrew S. McCraeath

The treatment which a steel receives, and the uses to which it may be applied, are frequently determined by the percentage of carbon which it contains; and especially is this the case in the different steel works in this country. The part which this element plays in the composition of steel is such an important one that a process for its accurate determination becomes an absolute necessity.

By Marie L. V. Gayler

WITHOUT diffusion taking place in liquid metals and alloys, no castings could be made; it is therefore the most important factor affecting the structure of metals. Diffusion involves the interchange of atoms, a process which takes place during the life history of an ingot. In the liquid, atoms are in a state of high thermal agitation, but this thermal vibration is reduced in amplitude with falling temperature. When solidification sets in, the atoms arrange themselves on an ordered space lattice and the changes in structure which take place in the solid are due to the interchange of atoms on this space lattice. The rate of atomic interchange-e.g., of diffusion-is most rapid at temperatures close to the melting point and decelerates as the temperature is lowered. At room temperature, the rate of diffusion is practically negligible in most alloys, and any change in structure can only be brought about by using methods which will accelerate the rate of diffusion. The rate of diffusion depends on three factors (I) temperature; (2) concentration gradient and (3) activation energy. The growth of grains and particles in the solid alloy also depend on these factors and are therefore intimately associated with diffusion. The rate of homogenization in a cast alloy depends on several factors, such as: (I) rate of solidification, which involves grain and particle size which, in their turn, depend on diffusion: (2) the nature of the constituents; (3) the temperature interval between the melting point of the metal or alloy and the temperature at which it is being heat-treated. It is well known that coarse, cast structures are extremely difficult-if possible to homogenize, and the finer the grain size and particle size, the more readily solid solution will take place. The rate of diffusion depends, also, largely on the nature of the constituents; for instance, copper and magnesium form solid solutions with aluminum quite readily but nickel and iron do not; neither do certain intermetallic compounds, such as alpha and beta FeSi. Furthermore, the actual formation of intermetallic compounds may be a very slow process, particularly when they are formed in the solid state as equilibrium products. For example, ßFeSi is formed in the solid as the result of the reaction aFeSi + Al?ß FeSi. The particles of aFeSi become sur¬rounded with a reaction ring of ßßFeSi. This layer is formed as the result of diffusion of atoms taking place between the aluminum matrix and aFeSi. As the amount of ßFeSi surrounding the core of aFeSi increases the concentration gradient becomes low and so the rate of diffusion of atoms also decreases until it practically ceases. This occurs after a comparatively thin layer of ßFeSi has been formed. It follows that when intermetallic compounds of this type are formed in the solid, as the result of diffusion, it is generally impossible ever to attain equilibrium, since the forma-

Jan 1, 1944

By W. R. Atkins

THE Negaunee mine is at the east end of the Marquette Range, in the city of Negaunee, on the Upper Peninsula of Michigan. Iron ore was first discovered on this property in 1883 by diamond drilling. A shaft was sunk soon afterward, and the mine has been worked continuously ever since. The total shipments from 1887 to&apos; Jan. 1, 1945, were 20,417,587 long tons. The mine was taken over by the present operators, The Cleveland-Cliffs Iron Co., in 1903. During the past four years, 1941 to 1944 inclusive, the property has produced an average of nearly a million tons a year, and has employed more than 400 men. GEOLOGY The ore body at the Negaunee mine lies in a large syncline dipping about 15° to the west, the ore coming to ledge at the east end of the trough. The ore occurs in the Negaunee formation of the middle Huronian age, which consists of ferruginous cherts and slates through which intrusions of diorite have occurred. Although these intrusions of diorite have an important bearing on the formation of ore on the range, they are not important in this ore body. Some faulting has taken place along the diorite intrusions, or dikes as they are called locally, and also other faults are known to exist across the formation. These faults do not complicate either mining or development of the ore body. The footwall consists of jasper underlain with Siamo slate; the hanging wall is jasper and ferruginous chert. Fig. I shows a typical cross section of the ore body. The ore body is quite regular, about 120 ft. thick in the middle of the syncline and thinning out toward both sides of the fold. Its width ranges from 400 to 800 ft., the average being about 600 ft. The footwall is uniform in dip and strike, but irregular lenses of ore often extend 50 to 75 ft. up into the overlying jasper capping. METHOD OF MINING Ore in the Negaunee mine has been mined by top slicing almost exclusively since 1903. This method of mining has been employed because it is especially adapted to the size and shape of the Negaunee ore body, and to the soft, sticky nature of the ore as well as the generally soft, broken jasper capping. Development The ore body has been developed from six different levels with intervals varying between l00 and 125 ft. On the average, the dip causes a horizontal offset of 350 ft. per level, and under these circumstances it has been necessary to carry on considerable development in rock to make available the ore lying along the north and east footwalls. This is not as disadvantageous as might be supposed, because of reduced pressure and the accompanying saving in maintenance costs. The development of the

Jan 1, 1946

By C. E. Mills

STUDIES of ground movement and subsidence resulting from mining operations cover a broad field. It is also a very important consideration and one that eventually affects nearly every mining operation of any extent. The damage to surface buildings, removal of mine surface plants and replacements of main hoisting shafts must reach an astounding expenditure were these cost figures available over a period of years. Were the subject one of mathematical formula and dependent only on the angle of draw of the walls or country rocks, the problem would be relatively simple. Consideration must be given to depth and extent of workings; structural conditions of the orebodies and enclosing country rock; physical properties of these same rocks, including schistosity, bedding, jointing, slips, dikes, faults, and other structural weaknesses. The method of mining, extent of openings, supporting pillars, and amount of moisture or water underground are other pertinent factors. With such a large number of variable factors, it is apparent that the subject of subsidence is one that must be based largely on experience and results at other mines where conditions are somewhat comparable. In presenting this paper, it is the intent to describe the progressive results of past ground movements at the United Verde, to bring out physical conditions largely responsible for this movement, but to refrain from theorizing on the ultimate extent of subsidence resulting from future mining operations.

Jan 1, 1934

By S. A. Wookey

More than 90 per cent of the ore produced by stoping at McIntyre is mined by horizontal cut-and-fill methods. The remainder is mined by square set and fill. In the stopes on the upper levels, mill holes are spaced 80 ft. apart and usually it is feasible to mine the breast for the full distance between the mill holes in one operation and to break, clean out and fill without any support for the roof or walls, other than the odd crown bar or sprag. The ore is scraped to the mill holes by small (10 to 15 hp.) air-operated slusher hoists. No grizzlies are used over the chutes and care is taken to break up the big pieces beforehand. Fill usually is spread by tramming sand or waste in a one-ton car from the fill raise. Fill raises are driven parallel to the strike of the vein and are inclined at approximately 48°. In long stopes, where more than one fill raise is necessary, they are spaced about 300 ft. apart. It is sometimes necessary to stand square sets for a short distance each way under the brow of the fill raise. support needed increases and on the lower levels and in some wide stopes where closer support of the back is necessary, it has become standard practice to timber the stope with 12 by 12-in. timber. Rough timber sets consisting. of caps, tightly blocked to the back and supported on posts 7 ft. high, are placed at about 5 ft. intervals. These sets are generally salvaged from the lower breast before blasting and are used again on the upper slice after the fill has been placed. In general, two or three breasts may be broken down before mucking out and filling and the ground stands long enough to enable this to be done safely. On the lower levels and in certain wide stopes and in heavy ground, a more intermittent method must be used. Only one breast or even part of a breast can be blasted and the back must be timbered before the ore can be removed. In these cases, sill timbers 16 ft. long, supported at one end on posts from the fill and at the other end on pins inserted in holes drilled in the face, are used. Timber cribs 5 by 9 ft. built from the fill to the roof and tightly blocked to the back are used throughout the mine to reinforce both the timber sets and the square sets.

Jan 1, 1946

By Joseph P. Brennan, Robert L. Vines

A historical comparison of the frequency of fatal coal mining accidents occurring underground in mines of various size ranges in the United States and in member countries of the Commission of the European Communities is presented. Frequencies are normalized on hours-worked and tons-produced bases. The comparisons rely on published and confirmed data and on theory for selective treatment of data in an effort to overcome reporting differences and basic differences in the mining conditions and system employed. Trends are identified ad projections made of the effect on accident records of various industry growth patterns. Conclusions are drawn regarding the reasons for differences between the records of U.S. underground coal mines and the records of those mines in European countries.

Jan 1, 1984

Executive ROBERT E. TALLY, Chairman WILLIAM H. BASSETT JOHN A. MATHEWS LOUIS S. CATES EDGAR RICKARD Finance H. A. GUESS HENRY KRUMB, Chairman H. G. MOULTON Admissions ERLE V. DAVELER, Chairman GEORGE D. BARRON H. K. MASTERS JOHN M. LOVEJOY P. A. MOSMAN Alternates E. L. ESTABROOK C. E. MEISSNER J. A. SINGMASTER FRED H. KAY

Jan 1, 1929