Search Documents

By J. M. McCormack, R. K. Saxer, J. R. Myers

ThE Knudsen effusion technique was used to determine the chemical activities of copper and platinum in binary Cu-Pt alloys in the temperature range 1542" to 1673°K. Wiebke and Matthes1 previously obtained chemical activities of copper and platinum in this system at 673° and 923°K by the electromotive-force measurement method. They reported that the copper activities exhibited negative deviation from Raoult's law at all compositions. The chemical activities of platinum were found to change from a positive to a negative deviation at 923°K. Myles2 recently studied this system in the temperature range 1265° to 1356°K by means of the torsional-effusion technique. His results indicated that both copper and platinum exhibited negative deviation from ideality at all compositions. The use of the Knudsen effusion technique to obtain the vapor pressure of metals and alloys is well-known.3 In this work, Knudsen cells were fabricated from seamless tantalum tubing of 1-in. OD and 0.020-in. wall thickness; cell bases and covers were cut from 0.010-in.-thick tantalum sheet and welded to the cells in an argon atmosphere. Orifices were drilled and reamed to approximate a knife-edge of 30-deg included angle. Calculation based on Balson's4 derivation showed the orifice to be nearly ideal. All temperature measurements were made with a Leeds and Northrup disappearing-filament-type optical pyrometer at the orifice of the cell, which closely approximated black-body conditions and eliminated the need for emissivity corrections. Details of the experimental techniques used, and the necessary correction factors required during this investigation are essentially those previously described.5,6 Before investigating the Cu-Pt alloys, vapor-pressure measurements were obtained over specimens of pure (OFHC) copper. The pure-copper data5 served to assure the accuracy of the experimental apparatus and technique.

Jan 1, 1967

By Edward Wichers

THE purpose of this paper is to set forth the matters of principal interest in connection with work done in the past few years on the purification of the metals of the platinum group, including the study and modification of methods already in the literature and the development of new procedures. For the most part, the results will be given in summary form, reserving the publication of detailed data and directions for a forthcoming paper to be issued by the Bureau of Standards. In recent years increasing interest has been shown in the preparation of the pure platinum metals, both by those concerned with the manufacture of the metals and their alloys for scientific and industrial purposes and those who are engaged in the study of the chemical or physical properties of the elements. The purification of the metals usually has been regarded as a matter so involved and difficult as to require the attention of specialists. It is hoped that this paper will show that any of the metals can be prepared in any desired degree of purity by relatively simple straightforward chemical methods. For the most part, it is thought that the methods given are suitable for small-scale refineries as well as for the laboratory; also, that they will bring the time required for the purification of any of the metals within reasonable limits. The new procedure suggested for purifying platinum should prove to be much shorter than any methods described in the literature.

Jan 1, 1928

By A. F. Meger

REPRESENTED here are the ideas and varied experiences of many people in the Hanna Coal Co. who have helped develop, over a number of years, an efficient and flexible method for spraying con- trolled amounts of oil on coal. Since the George- town preparation plant began operations early in 1951, oil treatment of coal has received special attention. It is believed that oil treating will satisfy present customers and also attract new markets. The first step in developing the new method of oil spraying was the construction of a dust cabinet for testing 50-lb samples of treated coal with the available oil sprays on the market. Tests results were tabulated for both indoor and outdoor storage.

Jan 7, 1954

By James R. Walpole

This paper will discuss the federal laws and regulations that are related to water quality. Both surface and underground water quality issues will be covered as well as point and nonpoint source requirements. Some of the subjects to be covered include the Federal Water Pollution Control Act (e.g., effluent guidelines, nonpoint source requirements, etc.), the Safe Drinking Water Act (e.g., underground injection control requirements; pits, ponds, and lagoons study, etc.), the Resource Conservation and Recovery Act (e.g., mining wastes study, etc.). The importance of related court decisions will also be discussed

Jan 1, 1982

By C. E. Birchenall, G. Derge

IN studying the kinetics of slag-metal reactions, it has become increasingly apparent that a complete knowledge of all aspects of interface phenomena will be required to clarify these processes adequately. A part of the data required for all oxidizing slags used in the refining of impure iron to steel is the rate of exchange of iron between the slag and metal phases. The simplest equilibrium of this type is that between liquid iron and iron silicate slag when both phases are equilibrated with the silica crucible containing them. In this study, the exchange of iron between the two liquid phases has been measured by using radioactive Fe as tracer. The observed high exchange rate indicates the ease with which such interfaces may be crossed in refining processes. The experiments required for this study involved relatively minor and normal modifications of well established techniques. Melting was accomplished by induction heating in heavy walled, fused silica, rotating crucibles." Rotation was used to minimize dilution of the slag by crucible erosion. The melting stock was ingot iron. Slags were prefused in iron crucibles using chemically pure grade oxide reagents. The special conditions applying to the active iron additions will be described for individual experiments. Suitable precautions were observed with regard to protection against radiation hazards.' Identification of Activity This particular study was initiated several years ago, but held in abeyance because the radioactive iron available at that time contained a foreign activity which concentrated in the slag so as to mask the iron activity and render the results unin-terpretable. With the benefit of experiences from other studies, radioiron of suitable purity can now be prepared. As received from the Isotope Div. of A.E.C., the unit appears to contain Fe + Fe50 and a high activity cobalt. The cobalt and iron are separated by repeated ether extractions, and the purified iron stored for sufficient time for the Fe'7 44 day half-life) to decay to negligible activity, leaving only Fe as the active isotope. This was confirmed by the absorption curves for slag and metal samples from heat No. 1. In Fig. 1 the experimentally measured points for the absorption curves of slag and metal are fitted by the calculated slope of 5.8 mg per sq cm in aluminum, which corresponds to the Mn K doublet emission resulting from the capture of an orbital electron of Fe" by the nucleus. This shows that the radioactive species are the same in both slag and metal and identifies it as Fe55 Description of Individual Heats For the first heat, the radioactive iron was contained in the prefused slag. The active Fe55 had been precipitated with carrier and was added as Fe2O3 during fusion in the iron crucible. The charge of 500 grams of ingot iron was melted, the protective iron sleeve added, rotation started, and a prefused, inactive slag was added to allow the system to approach equilibrium. After about 5 min at temperature, the wash slag was skimmed and the active slag added. Initial slag and metal samples were taken as soon as the slag was molten. Additional samples were taken at indicated intervals thereafter. Slag samples were dipped with a small iron spoon and metal samples were sucked into 1/4 in. ID silica tubes. The slag and metal samples were pulverized and mounted for radioactive counting. The slag samples were analyzed chemically for FeO. Temperature was read after the last slag sample by immersion of a Pt-Pt-Rh thermocouple protected by a fused silica sheath. Since no significant variation of rate with temperature was observed

Jan 1, 1954

By T. Sterry Hunt

THE Jones Mine (or Johannes Mine, as it was originally called, from a former proprietor), situated near Springfield, in the township of Caernarvon, Berks County, Pennsylvania, has long been known as a large deposit of magnetic iron ore, associated with more or less copper pyrites, and with malachite and chrysocolla. It occurs in a belt of soft schistose rocks which rest upon the Laurentian gneiss of the Welsh Mountain, and to the northward are soon concealed by the unconformably overlying Mesozoic sandstone of the region. These metalliferous strata belong to the Primal slates of Rodgers, which, in many other localities in this region, include similar deposits of iron ores associated with more or less copper, and often accompanied by chloritic and argillaceous schists, and, more rarely, by serpentine and small lenticular masses of crystalline limestone. To this same horizon belong the iron ores of Boyertown, Fritz's Island, and Roudenbusch, near Reading, Wheatfield, Cornwall, and Dillsburg (all of which are found along the northern border of the Mesozoic belt of * By the kind permission of Dr. F. A. Genth, of the University of Pennsylvania, I am now enabled to append to this paper the following hitherto unpublished analyses of the Cornwall ores.

Jan 1, 1876

Uranium, discovered in 1949 at Rum Jungle, 40 miles south of Darwin, N. T., was mined and processed to U3O8 from 1954 to 1963 by the Territory Enterprises Pty. Ltd. TEP is a Government company managed by Conzinc RioTinto of Australia Ltd. During this period, the uranium oxide was sold under contract to the Combined Development Agency, a joint Anglo-American uranium procurement agency. When the contract terminated in 1963, more than 31/4 million pounds of uranium oxide had been delivered which had been mined from three open pits. Copper ores, found with the uranium, necessitated the addition of a copper circuit to the concentrator. Copper concentrates containing 12,981 pounds of copper were also produced. Rum Jungle was the largest single industrial enterprise in the Northern Territories and, as such, was an important economic and social factor in this sparsely settled tropical region. To stretch out the life of this enterprise for the above reasons, and with the added possibility that the uranium market might improve, the Commonwealth mined out and stockpiled 650,000 tons of ore containing 9.6 lb of U,O, per ton, which is sufficient to sustain the treatment plant at 200 tpd until about 1971. In the plant, uranium is recovered from solution by solvent ex- traction. Current output is being stockpiled pending suitable market conditions.

Jan 10, 1964

THE hall of the Western Iron and Nail Associations having kindly been placed at the service of the Institute, the opening session was held at 3 o'clock, Tuesday afternoon, May 13th, with an attendance of about one hundred and twenty-five members. Mr. William Metcalf, of Pittsburgh, read an address of welcome on behalf of the Local Committee of Arrangements, to which President E. B. Coxe responded. The following papers were then read and discussed : Regenerative Stoves; a Sketch of their History and Notes on their Use, by John M. Hartman, of Philadelphia. Some Curious Phenomena Observed on Making a Test of a Piece of Bessemer Steel, by William Kent, of Pittsburgh. On the Use of Determining Slag Densities in Smelting, by Thomas Macfarlane, of Wyandotte, Michigan. After the reading of these papers each member was presented by the Local Committee with a schedule of excursions, a specially prepared map of Pittsburgh and surroundings, and a directory of industrial works, all tastefully bound, and also with a metal badge bearing the seal of the Institute, to be worn on the excursions. The second session was held on Tuesday evening. The following persons, duly proposed for members and associates of the Institute, were, on the recommendation of the Council, unan¬imously elected. (In this list are included those elected at the final session on Friday morning.) George Bartol, - Cleveland, Ohio. Luther S. Bent, - Steelton, Dauphin Co., Pa. Octave Chanute, - New York City. Albert H. Childs, - Allegheny, Pa. Theodore Cooper, - New York City. Andrew Cosgriff, - Brewster, Putnam Co., N. Y. William B. Crocker, - New York City. Henry M. Curry, - Pittsburgh, Pa. Charles Davis, - Allegheny, Pa. Henry F. De Bardeleben, - Birmingham, Ala. Herbert Du Puy, - Pittsburgh, Pa. Charles L. Fitzhugh, - Pittsburgh, Pa. W. S. Franklin, - Ashland, Md. F. G. Fricke, - Pittsburgh, Pa. Paul A. Fusz, - St. Louis, Mo. Ignatius Hahn, . Pittsburgh, Pa. Henry Hargreaves, - South Pittsburgh, Tenn.

Jan 1, 1880

By C. A. Stetefeldt

The hacienda Sauceda is one of the largest and finest haciendas in the vicinity of the City of Zacatecas, Mexico, and is said to reduce ores by the Patio process more cheaply than any other establishment. It receives its supply of ore from the San Acacio mine. This mine has been for some time, like most of the Zacatecas mines, out of bonanza, and yields, at present, ore of rather low grade. The silver occurs principally as silver-glance, ruby-silver and native silver, associated with pyrites of iron and copper, and some galena and zinc-blende, in a gangue of pure quartz, which takes the form of amythyst whenever the ore is of high grade. All the ore, as it comes from the mine, is broken by hand into small pieces, and sorted before it is delivered to the hacienda. Here it is first crushed dry in Chili mills, and then ground wet in arrastras to an impalpable powder. The sulphurets not decomposed in the patio process are separated in the settlers from the tailings and concentrated by hand. By roasting them in a reverberatory furnace with carbonate copperores, "magistral" is obtained. All machinery is driven by mulepower.

Jan 1, 1885

By Baxter C. Madden

Stress corrosion is defined and certain examples are illustrated. A number of test methods, to determine the resistance of materials to stress corrosion, are being developed at Wright Field. The criterion as to the validity of a method is stated. Three types of specimens and the method of stressing each type are described. Five different corrosive conditions are set forth. The results of tests to date, although too few for any general conclusions to be arrived at, are presented. The program for the continuation of the investigation is indicated. A bibliography is included. The development of the method of loading a cantilever-type specimen, so that a nearly constant stress at a large deflection may be realized, is presented as Appendix I.

Jan 1, 1945

By W. N. Page

The Red-Ash colliery was the scene, March 6, 1900, of an explosion by which some fifty men were killed or wounded, and much property was injured or destroyed. On March 19th, the earliest date at which entrance was practicable, I examined the mine with the view of determining the extent, cause and point of origin of the explosion, and with the permission of Mr. F. Howald, the manager, and the owners of the property, for whom the examination was made, I present in this paper some results of that examination, comprising the essential portions of my report to them. Location and Plan of the Mine. The Red-Ash colliery, situated on the south side of New river, next below the Rush Run mine, with which the underground workings are connected, is a drift-mine, the entrance to which is on a slope, about 500 ft. above the river. (Fig. 1 is a plan of the workings, in which the points where human bodies were found are designated by numbers.)

Jan 1, 1901

By L. E. Wilsey, R. A. Morse, P. L. Terwilliger, Howard N. Hall, P. M. Bridges

Theoretical and experimental investigations of a constant pressure gravity drainage system are reported. Experimental data are presented to show that recovery to gas breakthrough by gravity drainage is inversely proportional to rate. The gravity drainage reference rate, which is numerically equal to the so-called "maximum theoretical rate of gravity drainage" is shown to have no particular significance from a recovery standpoint. Before this rate can be used as a basis of comparison for recoveries, it is necessary that the relative permeability and capillary pressure characteristics and displacing fluid viscosities be identical for the systems compared. A method is presented by which accurate prediction of the performance of a gravity drainage system can be made. Close agreement between experimental and calculated drainage performance shows that steady state relative permeability and static capillary pressure data can be used to describe fluid displacement behavior. The very wide range of liquid recoveries before gas breakthrough which result from production rate variation alone demonstrates the importance of this factor in planning depletion of a gravity drainage reservoir. Calculated results are presented which show that little additional recovery can be expected from a high pressure gravity drainage system between the times of gas breakthrough and attainment of such high gas/liquid ratios as to make further pressure maintenance impractical. INTRODUCTION It bas been recognized for some time that gravity forces play an important part in the recovery of oil from some types of reservoirs. Field experience has shown that under certain conditions, gravity drainage can result in very high oil recov- eries. Qualitative reasoning has led most engineers to the general conclusions that: (1) Where gravity drainage is important, the reservoir pressure should be maintained by gas injection at the crest of the structure to prevent shrinkage of the oil in place and to keep a low viscosity so the oil can drain at the fastest possible rate. (2) Recovery by gravity drainage is rate sensitive. A survey of the literature indicates that while considerable work has been done on the effects of gravity in oil production problems, no satisfactory method of calculating the performance of gravity drainage reservoirs has been reported.1,2,3,4,5 In the absence of any proven method of calculating reservoir performance, the level at which pressure should be maintained and the rate of production for most efficient operation has been open to debate. The limits and general character of the recovery us rate relationships are apparent from the following: As rates of production approach zero, oil will drain by virtue of its own weight fast enough that the saturation distribution is always approximately the same as the original static capillary distribution. That is, at the gas-oil contact the liquid saturation goes from 100 per cent to a value of perhaps 10 to 30 per cent in a very short distance, so that as production continues. a relatively sharp gas-oil contact moves down-structure, leaving a very low residual oil saturation in the originally oil saturated zone. At very high rates of production, the oil that drains by virtue of its own weight is negligible and recovery will approach that of a horizontal gas drive, leaving a much higher residual oil saturation. At intermediate rates of production. recovery should be between these extreme*. Despite the lack of quantitative methods, tentative agreement had been reached on the question of optimum producing rate. It has been generally concluded that rather sharp decrease in recovery would occur at rates of production above the "maximum rate of gravity drainage" and hence this rate should not be exceeded. The "maximum rate of gravity drainage" is defined as the rate of production from a 100 per cent

Jan 1, 1951

By Fred Hellmann

IT IS hardly to be doubted that the opportunity within the grasp of the mine manager for beneficent and helpful action in relation to young engineers seeking employment under him is very broad and very big. It is my experience that a manager usually has a strong inclination to help along those who have chosen the career which he has selected for himself, and to aid them and support them as their steps tread the paths which his own feet have previously followed. He has .a strong sympathy for them in their efforts, he almost yearns to shield them from the mistakes into which he himself fell, and to assist them to avoid the pit-falls of which he knows by bitter experience. Yes, this tendency and inclination is strongly developed in most managers, and they would welcome the opportunity of extending the helping hand, if they knew precisely how best this could be done.

Jan 5, 1923

By A. R. Troiano, E. A. Steigerwald, F. W. Schaller

The initiation of localized cracking in hydrogenated high strength steel was dependent on the developmeni of a critical hydrogen conceniration and relatively insensitive to the magnitude of the applied stress. The stress was believed to influence the deluyed failure process by providing the means for grouping the hydrogen. On the basis of an assumed distribution law the observed changes in the lower critical stress as a function of notch acuity, yield strength, and temperature were predictable over a significant range of these variables. THE phenomenological characteristics of delayed failure in high-strength steel have been comprehensively investigated and the behavior has been attributed to the strong embrittling action of hydrogen.1-3 Delayed failure or, as it is also termed, static fatigue, is the most sensitive means of detecting hydrogen embrittlement since it allows the maximum time for hydrogen diffusion during a test.3 The nature of delayed failure cail be aptly described by four parameters which are schematically depicted in Fig. 1. The upper critical stress corresponds to the rupture stress in a conventional notch tensile test. The lower critical stress or static fatigue limit is the stress below which no delayed failure will occur. The incubation period is the time required for the formation of the first crack and the fourth parameter is the failure time. An increase in hydrogen content, notch acuity, or strength level of the material increases the susceptibility for delayed failure by decreasing the lower critical stress, the incubation period, and the time to failure.lY3 A decrease in test temperature prolongs the incubation period in accordance with the lower diffusion rate of hydrogen, and also de-

Jan 1, 1961

By D. M. Beeson, G. D. Ortloff

Water-propelled banks of carbon dioxide recovered both high- and low-viscosity crude oil substantially in excess of that recovered by water flood in linear flow model experiments. The increase in oil recovery is explained by oil swelling and viscosity reduction. Additional oil was recovered by solution gas drive at the end of the carbon dioxide floods when the model systems were depres-sured. This study was an investigation of the use of a water-driven carbon dioxide bank to recover crude oil. Techniques involving the injection of carbon dioxide have aroused con-siderable interest in recent years among methods considered for increasing oil recoveries. A number of investigators have studied the process in the laboratory1-' and in the field.7,5 Laboratory studies referenced indicate that carbon dioxide in conjunction with water flooding recovers more oil than does water flooding alone. These re- ports diverge widely, however, in stating magnitude of improvement. We believed that a water-driven carbon dioxide bank would increase recovery of crude oils by two mechanisms: viscosity reduction and oil swelling. Due to reduction in the oil viscosity caused by solution of carbon dioxide, displacement efficiency should be improved. In addition, the residual oil should be highly swollen by the carbon dioxide held in solution. Thus, the final residual oil saturation, in terms of stock-tank oil, would be lower than in the absence of carbon dioxide. To test this hypothesis, experi-

By C. F. Tolman

Discussion of the paper of C. F. TOLMAN, JR., presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 401 to 433. Louis C. GRATON, Cambridge, Mass.-Of particular interest at this time is any paper that deals with chalcocite, the characteristic product of secondary enrichment and the copper mineral of greatest commercial importance, and that seeks to aid in the distinction between primary and secondary chalcocite-a distinction of much scientific and practical importance but one which thus far it has proved difficult to draw. The present paper on this subject by Professor Tolman, like the ,many preceding it which he and his colleagues at Stanford have published in the last couple of years, contains much of interest and suggestiveness. Without endeavoring at this time to review or comment upon Professor Tolman's conclusions in detail, I may say that many of them are in accord with the findings that my associates and I have been accumulating in the course of studying secondary enrichment in many of the copper deposits of the country. On the other hand, it goes without saying that in this comparatively new field of research or, at least, a field in which

Jan 5, 1916

Jerome L. Boyer, Reading, Chairman; William L. Sheafer, Pottsville, Secretary ; Levi Quier, Reading, Treasurer; Robert Allison, Port Carbon; James Archbald, Jr., Pottsville; William Atkins, Pottsville; D. P. Brown, Lost Creek; William McH. Boyer, Rending; Albert Broden, Reading; George Brooke, Birdsboro; Frank Carter, Pottsville; H. P. Cooper, Pottsville ; J. H. Carpenter, Reading; E. S. Cook, Pottstown; B. Halberstadt, Pottsville; Hakon Hammer, Pottstown; J. Hartshorne, Stowe; M. P. Janney, Pottstown; R. C. Luther, Pottsville; N. Muhlenberg, Reading ; W. H. Morris. Pottstown ; George L. Norris, Reading; G. H. Potts, Pottstown ; H. Potts, Pottstown; S. M. Riley, Ashland ; J. S. Robeson, Pottstown ; Jas. P. Roe, Pottstown; A. W. Sheafer, Pottsville; Heber S. Thompson, Pottsville; Bard Wells, Pottsville; E. C.Wagner, Girardville; N. B. Wittman, Birdsboro. Reception Committee.— George Brooke, Chairman; Robert Allison, J. H. Carpenter, Edgar S. Cook, R. C. Luther, W. H. Morris, H. S. Thompson. Hotel Headquarters.—The Neversink Mountain Hotel, near Reading, Pa. All sessions were held in the hotel. The opening session was held on Tuesday evening, October 11. Mr. Jerome L. Boyer, Chairman of the Local Committee, called the meeting to order, and introduced Mr. John F. Daniel], Jr., VicePresident of the Reading Board of Trade, who delivered an address of welcome, in the course of which the industrial and commercial importance of the city was effectively outlined by skilful use of the statistics of leading branches. From this statement the following particulars are condensed for preservation: The Board of Trade has about 300 members. The annual value of the manofttctures (taking mainly the figures of 1891) is as follows: Iron manufactures, about $16,000,000 (including boilers and flues, $323,000; hardware, locks and butts, $1,650,000; pig-iron, wrought-iron pipe and machinery, $8,400,000; beams, bridge-work and steel, $4,000,000; bolts, nuts, rivets, etc., $1,000,000; stoves, $659,000); silk and cotton goods, $1,725,000; boots and shoes (one concern only), $150,000; ropes and cordage, $600,000; fire-brick, terra-cotta and glass, $320,000; wool and fur hats, $3,000,000; cigars (105 millions), upwards of $3,150,000. The street and elec-

Jan 1, 1893

By Wallace Thorneycroft

This paper by Mr. Thorneycroft, Past President of the Institution of Mining Engineers (Great Britain), and chairman of its Subsidence Committee, is a valuable contribution to the assemblage of data on ground movement and subsidence from coal mining. It deals with the effects of advancing longwall, a method almost universal in Europe but as yet little used in the United States outside of Northern Illinois and in a few scattered places elsewhere in thin coal beds, as in the Lexington field, Missouri. Canon City field, Colorado, and the Birmingham field, Alabama. Although by advancing lougwall, a maximum recovery of coal is obtained and it has to be employed where there are weak shale roofs, especially in deep mines, it is a more expensive method of operation unless the mining conditions are suitable, which is unusual in the United States. On the other hand, there is a growing use in this country of what is essentially retreating longwall, with an approximately straight break-line as described by Rayburn.1 With this method, in which the pillars are substantial, it was shown that the ground movement effect is practically identical with that of advancing longwall, hence the value to mining engineers of the precise data given by Mr. Thorneycroft. His study is unusual in several respects; it deals with conditions connected with the mining of a coal bed 20 in. thick, about 490 ft. below the surface, over a mined-out area in a 5-ft. bed about 90 ft. below, which had been mined about 12 years earlier. Both mines passed under Plean House, a building of massive cut stone construction built over a century ago, in which Mr. Thorneycroft resided throughout the under-mining period. Slight cracks opened in the walls as the longwall face approached the house in mining the upper seam, and closed after the face passed and subsidence took place. In the northwest wall, the last wall the face passed under, some stone blocks were broken, which was attributed to a strike period when the advance of face came nearly to a standstill. Other than this there was no perceptible permanent damage, as indicated by the photographs taken by the undersigned in 1923 (Figs. 1 and 2). Mr. Thorneycroft used a novel means of studying the successive positions of the corners of the building: he hung plumb bobs from the eaves and traced the paths of the respective plumb bob points on level surfaces. The angles made by the house walls with the plumb bob lines gave measures of the slope of the subsidence wave at the respective points. A slight upward wave was indicated by the surveys ahead of the subsidence, which would appear to be due to a tilting over of the massive sandstone stratum in the roof measures near the surface, the edge of the coal face acting as the fulcrum.

Jan 1, 1931

For the year ending February, 1919 PRESIDENT SIDNEY J. JENNINGS NEW YORK, N. Y. PAST PRESIDENTS L. D. RICKETTS NEW YORK, N. Y. PHILIP N. MOORE ST Louis, Mo. FIRST VICE-PRESIDENT C. W. GOODALE BUTTE, MONT. TREASURER GEORGE C. STONE, NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND, NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 7, 1918

By John J. Egan

THE present list of problems relating to the physical chemistry of steelmaking has been prepared by the Committee on the Physical Chemistry of Steelmaking, from answers to a questionnaire Submitted to a number of metallurgists engaged in both industrial and educational work throughout the United States. The purpose of the project is to make available to research laboratories a list of problems, all reduced to their simplest terms, the solution of which would aid in creating a better understanding of the steelmaking process. It is not intended to restrict the problems to practical steelmaking. The list also includes the study of the properties, and their correlation, as well as the physical and chemical reactions, of all Substances that occur or that may be in any way associated with steelmaking operations, Such as metallic substances, refractories, nonmetallic inclusions, and the constituents of slags. Many of the problems can be carried out in university or other research laboratories. Others may be most successfully attacked by cooperation of the research men with the operating personnel. It is the Committee's earnest wish that this cooperation be fostered. It is requested that investigators who are working on any of the problems listed and who anticipate future publication of their results, notify the Secretary of the Committee that such investigation is in progress. Suggested additions to the present list are also requested. The Committee is undertaking to act as a clearing house for information regarding the topics in this field that are being actually studied. Interested persons are invited to correspond with the Secretary. I. Data involved in the state of equilibrium for the various systems (laboratory work, almost entirely). A. SPECIFIC HEATS, HEATS OF FORMATION, ENTROPIES AND FREE ENERGIES OF VARIOUS PURE ELEMENTS OR COMPOUNDS; ALSO CERTAIN TYPICAL SLAGS AND REFRACTORIES. I . Determination of specific heats and entropies of oxides, sulphides, nitrides, etc. over a wide temperature range. 2. Determination of free energies of oxides, sulphides, nitrides, etc. over a wide temperature range. 3. Determination of the heats of formation of the oxides, sulphides, nitrides, etc. 4. Determination of the thermodynamic properties of the more important mineralogical constituents of the basic open-hearth slags such as calcium silicates, calcium phosphates, calcium ferrites, manganese silicates, FeO and Fe2O3. 5. Determination of the specific heats of open-hearth slags, including liquid silicates, if possible.

Jan 1, 1941