Search Documents

By D. K. Crampton, H. l. Burghoff, J. T. Stacy

The study of copper alloys of the age-hardening type has received considerable attention, and, among the alloys which the authors have, considered, those containing small amounts of nickel and phosphorus as essential constituents seem especially interesting. Such alloys have attractively great capacity for being hardened and also have relatively high electrical and thermal conductivity in the hardened state. In addition, it has been found that the increase in hardness and strength imparted by aging can be greatly augmented by cold-working, so that excellent combinations of conductivity and strength are obtainnble. In view of the possible importance of the alloys, it was considered desirable to investigate the solubility relationships in the copper-rich portion of the copper-nickel-phosphorus system. This paper present's some of the results obtained in this investigation to date and also gives propertics of typical alloys that appear to be of commercial interest,. Review of literature Copper-nickel System,.—The binary coppcr-nickcl system has long been known to consist of a series of simple solicl solutions, copper and nickel being miscible at all tempcrat'ures and concentrations. This was establisl~cd by Guertler arid Tammannl in 1907 and confirmed by Tafel2 in 1908. Copper-phosphorus System.—The copper phosporus system has been studied by numerous investigators, so that the copper-rich portion is now definitely known. As most recently determined by Lindlief," his system has a cutectic at 8.38 per ccnt P, cuteetic temperature being 714° C. Components of the cutectic are Cu3P and alpha solid solution. Solid solubility of phosphorus in copper, according to Mertz arid Mathewson decreases from a maximum of about 1.75 per cent at 714' C. to about 0.6 per cent at 300' C.

Jan 1, 1940

By G. W. Thomas

Jan 1, 1967

By R. W. Vieth, S. A. Bradford

THE orientations of tetragonal tin crystals are commonly examined by either the transmission Laue method or the back-reflection Laue method. The predominant planes and zone axes of the pattern are plotted on a Wulff net and indexed by measuring the angles between planes and directions. The problem of identifying the Laue spots has been approached in several different ways. Nicholas 1 tabulated interplanar angles for ten planes but did not relate the angles to permutation of indices or sign. A table of angles between adjacent planes and of angles between adjacent zones was published by Chandrasekhar and veal.' These tables are very helpful, provided the film shows all the low-order zones that occur within about 20 deg of each other. Frounfelker and Hirthe's compilation3 of angles between the (001) plane and twenty-nine other planes is useful for the indexing, only if the (001) spot can be found on the film. For all but the simplest orientations, however, more information is needed to index the diffraction spots. Standard stereographic projections, such as those published by Bicelli, 4 provide part of the information required. By their nature, these projections show the positions of only a few zone axes. In the tetragonal system many low-order zone axes are not normal to the planes having the same indices. Consequently, planes and directions can have entirely different positions on a stereographic projection. For example, the [011] zone axis is 33 deg from the normal to the (011) plane. The crystallographic orientation usually has to be deduced from a combination of the predominant zone axes and a few low-order planes that appear on the film. In addition to a standard stereographic projection of the planes, a stereographic projection of the directions is needed. Such a projection can be constructed from the angles given in Table I. To provide more information about angles between planes and directions, we have calculated interplanar angles up to (332) and angles between planes and directions up to [332] on an IBM 1620 computer. The angles are differentiated according to permutations of sign and indices. Those doing research on tin single crystals are welcome to request a copy of these tables from the authors.

Jan 1, 1967

By E. F. Young

The Porter Tunnel will open up 10 million tons of coal for Philadelphia & Reading which can be taken without hoists or pumps.

Jan 3, 1951

By H. E. Mussey

When the American Institute of Mining Engineers visited the Birmingham district in May, 1888, the four Ensley furnaces (Fig. 1) then completed were referred to as monumental.' Their dimensions are givcn in Table 1. Mr. Gordon stated, with considerable satisfaction, that on the preceding day one furnace had produced 165 tons. The blast was

Jan 1, 1925

By B. Chalmers, L. Bäckerud

The growth temperature of dendrite tips has been measured in a binary alloy system, Al-Cu, as a function of rate of formation of solid phase. Metallographic examination has rerealed the dendritic structure dereloped during different stages of the freezing process and factors influencing the undercooling, such as solute buildup, surface tension, and kinetic effects, have been estimated. Practical implications of the results are discussed. THE development of a dendritic growth pattern during the solidification of metals and alloys has an influence at least equal to that of grain size on the properties of the casting or ingot being produced. and consequently much interest has been devoted to the study of this phenomenon. A review of the knowledge gathered up to 1964 has been given by Chalmers.' Among recent publications in the area the works of Jackson et al 2 and Flemings and his coworkers3,4 are of special interest. This work is an experimental study of the factors which influence the development of a dendritic pattern during the solidification of a typical binary alloy system, A1-Cu, when there is no heat source in the liquid. This means that the temperature and the temperature gradient are controlled by the heat extraction from and latent heat evolved by the growing crystals. EXPERIMENTAL PROCEDURE Samples were prepared from a master alloy made up of aluminum, 99.995 pct, and copper. 99.99 pct, of the concentrations given below and of sufficient size to fill cylindrical graphite molds of 35 mm ID and 35 mm height. Bottom. wall. and lid of the graphite molds were all of 6 mm thickness, Fig. 1. Thin ceramic thermocouple shields could be introduced at different positions in the sample through holes in the lid. The assembly was heated in a small vertical resistance furnace to a suitable temperature. 700° to 720°C. which is well above the melting point of the sample. It was thereafter taken out of the furnace and chilled at selected rates, and the temperature changes in the sample were recorded. For high sensitivity in the temperature recordings, a reference thermocouple was held in a solidifying pure aluminum melt. which was very well insulated and therefore was at a constant temperature. 660°C, for nearly half an hour. The thermocouples were connected so that the difference voltage was fed into the recorder of which the most sensitive range was 1 mV. Temperature variations could be read to within 0.l°C. The thermocouples used were of the Chromel-Alumel type (28- or 38-gage wires) and the recorder a two-pen Moseley strip chart recorder. The different rates of chilling were obtained in the following way. a) The graphite crucible was wrapped in one or two layers of an insulating. feltlike material (Fiberfrax paper from the Carborundum Co.). The drop in temperature per unit time after complete solidification could thereby be varied from 8" to 18°C per min. This corresponds to a rate of heat extraction in the given samples from 0.08 to 0.17 cal cm-' sec-I. 6) The bare graphite mold was placed free on a piece of firebrick. The measured temperature drop was around 50°C per min (-0.5 cal cm-" ' sec- I). c) By blowing compressed air through a tube with many holes surrounding the mold in a ring shape. the rate of heat transfer could be raised to 150' to 200°C per min (-1.7 cal cm-3 sec- I). d) Cooling rates around 1000 C per mill (-9.4 cal cm-3 sec-l) were obtained by substituting the air in the device used in c by water. The range of cooling rates used in these experiments correspond to technical casting processes from slow solidification as obtained in sand molds to very rapid freezing which occurs in some continuous casting and welding processes. EXPERIMENTAL RESULTS The A1-Cu system was chosen for the experiments: the relevant part of the phase diagram is reproduced in Fig. 2. Observation of the Center Temperature. When a thermocouple is inserted in the center of the melt. the type of cooling curves obtained at slow solidification rates differs little from numerous published curves from similar systems. and the solidification pattern

Jan 1, 1970

CHARLES E. GUILLAUME,* .Sèvres, France written discussion?).-Referring top. 2052, experiments made at the end of the year 1884showed a remarkable agreement between the indications of various verre dur thermometers of which all the corrections had been determined with the greatest possible precision. The maximum deviations not attributable to the comparisons themselves were then about 0.002 to 0.003 degree. Much later, greater differences began to show. They were caused by the fact that the glassmaker-had modified the composition by adding to it a small quantity of lead. Efforts are now being made in France to obtain a regular, supply of glass made according to the old formula. The determination of the boiling point of sulfur made by Chappuis,1 444.5°, accords very well with the value noted on p. 2054. The International Committee of Weights and Measures and the General Conference have already considered the future abandonment of the hydrogen scale in favor of the thermodynamic scale. The hydro-gen scale appears to be, in their estimation, a transitory one, happily so closely approaching the final scale that no correction should be necessary for all measurements of temperature made during the last 30 years.

Jan 12, 1919

By Edgar Trask

EACH branch of engineering seems to depend on the cooperation and contribution of some other branches to enable it to produce more efficient methods and appliances for man to use. The purpose of this paper is to show approximately the gain in efficiency of self-propelled merchant ships when steel of greater elasticity is substituted for mild steel in some of the strength members and alu-minum alloy is substituted in some of the parts where strength is not essential. The new steel will have some greater strength and a much greater elastic limit in the as-rolled condition, and must be readily weld-able under ordinary conditions of shipbuilding. Naturally, its cost may be more than mild steel, but if the demand is great that excess cost may be reduced to an amount that will make its use more economical than that of the present mild steel. There appears to be a well defined axiom in engineering today that to use the least power to carry a given load the weight of the carrier must be reduced to a minimum. This minimum must be, of course, consistent with the necessary strength, rigidity and durability and it must not be attained at an excessive cost where the fixed charges of the carrier will exceed the savings in, operating the motive power. Recent railroad equipment is a notable example of this, and in these trains alloy steels and aluminum together with less weight per horsepower of the power plant are reducing the weight of the carrier and hence the total power required for moving the paying load. Before considering the application of these metals to shipbuilding, it is well to explain some of the fundamentals of ship design.

Jan 1, 1936

By A. G. Metcalfe, A. Siede

The hardening of annealed copper during fatigue testing appears to be independent of the applied stress and to occur largely within the first 4000 cycles. Copper hardened by fatigue is more resistant to annealing than copper hardened by static means, and softens by a multistage process. Creep studies at 300°C show that copper hardened by fatigue also has greater resistance to creep than statically hardened copper. Some theoretical explanations are discussed. RECENT interest in the behavior of metals subjected to fatigue stems from observations of phenomena which could not be explained by current theories of the structure of metals. In 1953 Bullen et al.l showed that the hardening caused by fatigue at low stresses did not cause severe bending of the lattice as did hardening by static methods. This was later confirmed by Wood, 'and Broom and Ham.3 Clarebrough et al4 showed that as the stress level used in fatigue hardening was increased, bending of the lattice was introduced, eventually approaching that of metals deformed by conventional cold-working methods. The type of hardening introduced by fatigue has other interesting characteristics. Kemsley5 showed that copper fractured by fatigue at low stresses resisted annealing as compared to copper hardened an equal amount by static means. The work of Clarebrough etal, shows that the manner of energy release during annealing differs for fatigue-hardened and statically hardened metal in both magnitude and temperature range of release. In addition to hardening of the lattice, fatigue has been shown to cause softening in materials previously hardened by static methods,5 and also in age-hardened alloys.7 The superposition of a small fatigue stress on the static loading of high-temperature alloys has been shown to increase their resistance to creep.' The present work was an attempt to determine the relationship between fatigue hardening, resistance to annealing, and the creep properties of pure copper. EXPERIMENTAL PROGRAM The program described here was designed to answer three questions: 1) Can stress-cycle combinations well below the failure values give significant increases in hardness? 2) Does hardening, under different stress-cycle combinations, give increase resistance to annealing? And if so— 3) Does superior resistance to annealing confer superior creep properties over statically hardened material? Three-quarter hard OFHC copper was annealed in vacuo at 550°C for 1 hr to produce a strain-free material having a fine grain size and uniform hardness. (The standard deviation of the mean hardness of the annealed samples was less than + 1.9 Dpn). Annealing was performed after machining the fatigue specimens so as to avoid work-hardened surfaces. Jigs were used to avoid distortion. The fatigue properties of the annealed copper were determined using an accurately aligned Baldwin-Sonntag SF1-U machine operating at 1800 cycles per min. This limited the minimum number of cycles which could be examined to about 4000 stress reversals. Since failure resulted in specimen damage, hardness increase with number of cycles was measured by testing specimens fatigued to different fractions of the failure values. The results are shown in Fig. 1, and are superimposed on the S-N curve of the copper in Fig. 2. The resistance to annealing of fatigue-hardened material was compared to that of material hardened by uniaxial tensile straining. Specimens hardened to equal values by both methods were progressively annealed for 1 hr at temperature in vacuo. After each annealing treatment the hardness was measured using a Leitz Durimet hardness tester with a 500-g load. At least five tests were made for each hardness determination. The standard deviation for individual specimens varied from 0.26 to 1.48 hardness points. The results are shown in Figs. 3 to 5. The discontinuous nature of the annealing process has been brought out by drawing idealized curves through the data points. This can be justified by the consistency of the results as well as by general agreement with results of Kemsley.5 The creep resistance of fatigue-hardened and

Jan 1, 1960

By I. H. Silberberg, R. L. Reed, O. K. Kimbler

interfacial films have frequently been observed at interfaces between certain crude oils and water. Several investigators have postulated that the presence of these films should influence the efficiency of oil recovery in water drive or waterflood operations. They may also influence the stability of emulsions which are sometimes a problem in petroleum production, and may be a factor in the fonation of paraffin deposits in oil well tubing and flow lines. This paper presents a technique with which a modified Langmuir film balance may be used to study the compressibility and collapse pressure of these natural interfacial films. Experimental data are presented for several nude oil-water systems. Data developed are used to infer the phase state of the film as a function of such variables as rate of reduction of interfacial area, ionic composition of the subtrate and pH of the subtrate. A film of known physical characteristics is shown to have a sinnificant effect on oil recovery from an unconsolidated sand pack. Possible applications of these results to petroleum production are discussed. INTRODUCTION The use of water to displace petroleum from reservoir rocks is of major importance both as a primary and a secondary recovery process. As water invades the rock, oil is completely displaced from some pores and left as a discontinuous phase in other pores. The manner in which water moves from pore to pore is strongly influenced by capillary forces. In view of the complexity of reservoir fluid systems, there can be little doubt that complicated interactions take place at both the liquid-solid and oil-water interfaces. One of the more interesting, and least understood, of the phenomena which take place at the oil-water interface is the formation of interfacial films. These films are believed to result from the adsorption of high molecular weight polar molecules at the interface.l.2 Presence of such molecules may cause a striking alteration in interfacial tension. When the oil-water interfacial area of certain crudes is rapidly reduced, a thin region (film) about the interface assumes the appearance of a solid membrane, and striations, wrinkles and gross distortions may occur. If such a film is solid, it should greatly alter the interfacial tension normally assumed to exist between the oil and water phases. If the membrane is continuous, a solid phase would separate the oil and water. Interfacial films between crude oil and water were observed in 1949 by Bartell and Niederhausers who commented upon the apparent rigidity of the films and their possible importance in the petroleum industry. Morrell and Egloff4 had earlier attributed the extreme stability of emulsions of sea water in fuel oil to very stable asphaltic films. Numerous investigators have observed rigid films in the course of crude oil-water interfacial tension determinations by the pendent drop method. Several investigators5,6,2 have separated inter-facially active materials from crudes and attempted to characterize them chemically. Reisberg and Doscher,2 using Ventura crude, showed the interfacial tension against water (as measured by the pendent drop method) to be affected by aging, contraction and expansion of the interface, and the pH of the water. These investigators attributed the adhesion of oil to a water-wetted surface and the distortions of flow paths in glass capillaries to the presence of rigid films. Dodd7 has studied the interfacial viscosity of adsorbed films and found them to be non-Newtonian in behavior. Craighead and Harvey8 reported a series of displacements in tubes packed with 60 mesh glass beads. They interpreted the results as indicating an effect of stearic acid films on waterflood recovery and imply that natural films may produce similar results.

Jan 1, 1967

By A. T. Peters

DURING an investigation concerning the use of large nozzles for pouring of low-carbon rimming steels, the practical details of which were reported elsewhere, it was noticed that increases of nozzle sizes were generally followed by improvements of slab surface quality. It is the purpose of this note to present the data available and some tentative opinions about this phenomenon. The problem of correlating pouring rates with the metallurgical performance of steels is complicated by several factors. The two most important are; 1) Variations of the steel pouring rate throughout a pour, these being due to the nozzle erosion, which enlarges the bore area, and the dropping ferrostatic pressure in the ladle. The pouring rate is lowest towards the end of a heat when the ladle is nearly empty. 2) Variations in the ingot pouring time due to the different ingot weights poured. Consequently, the use of the average pouring rate of a heat may not be exact, but in large-scale production it is not practical to treat ingots separately according to their pouring rates. The variations of ingot weights and sizes may be overcome by considering the rate of rise of steel in the mold. Hence, the average rate of filling of molds throughout the pour of a heat, inches per second, will be used in this note. Every ingot rolled at Inland is rated at the blooming mills prior to hot machine scarfing as being good, fair, or poor for cracks, scabs, and checking. The latter term refers to the network of breaks or lines associated with overheating or burning in the soaking pits. It is also known that thin-skinned steel is prone to show this defect if the subsurface blowholes are exposed during reheating or rolling. The experiences with the surface quality of slabs rolled from ingots poured at different rates are presented in Fig. 1. The data represent nearly 11,000 ingots. It appears that all three types of defects are in-

Jan 1, 1960

By P. H. Dudley

I HAVE taken the liberty of calling the researches herein mentioned industrial, to distinguish them from those strictly scientific, where every known appliance is used to insure accuracy in determining principles. The industrial researches are made to ascertain wherein we have failed to embody, in practice, the principles which have been fully demonstrated by the more purely scientific investigations. So far the researches have been mostly confined to the conditions of combustion as used in locomotive furnaces, although we have examined, to some extent, furnaces under marine and stationary boilers. The products of complete combustion are gases, and, knowing what we should have, it is at once shown by analyzing the products whether the desired reactions are taking place. In spite of imperfect furnaces, lack of system in the arrangement of grate-bars and exhaust nozzles, the results are not altogether vitiated, because the analyses are not closer than one-tenth of one per cent., as under the present conditions it is hardly possible to collect gas exactly under the same conditions at different times. All of our industrial operations have developed in the past few years so rapidly, nearly all of them paying, that, until within the past three years, comparatively little attention has been given to their economy outside of the profession. Great corporations have not asked and considered the question in earnest, can we utilize our heat so as to produce the same effect at less cost? The applications of heat are so extensive, entering into every branch of industry, the principal power used to carry on metallurgical processes, to conduct transportation, that its economical generation becomes of universal importance; in fact, its economical generation and application is the leading industrial question of the day. It is stated by those who have given the subject much attention, that in our best steam-engines not over 10 per cent of the theoretical value of the fuel is utilized, and upon locomotives it is far less, probably not exceeding under the most favorable circumstances 5 or 6 per cent. In recent experiments made with the dynagraph, in drawing trains upon the Lake Shore and Michigan Southern Railway from Cleveland to Erie, 95i miles, we found the force required to draw a stock train of 709 tons to be 2,498,396,320 foot-pounds, exclusive of the force to move the locomotive itself. We

Jan 1, 1876

Reno, Nevada. J A Fulton, Director For publications of either the Mackay School of Mines or the State Bureau of Mines, address the School of Mines at the given address. Except where the contrary is indicated in the following list, available publications are sent free From the Mackay School of Mines. Bulletin 1, The identification of Nevada's common minerals, 50 cents; 3, Notes on the ore deposits of Cave Valley mining district, Lincoln County, 4, A preliminary survey of the Scossa mining district, Pershing County, 5, Ore deposits of the Gold Circle mining district, Elko County, 6, Bedded deposits of manganese oxides near Las Vegas, 7, Spruce Mountain district, Elko County, and Cherry Creek (Egan Canyon) district, White Pine County From the State Bureau of Mines: Bulletin 1, Mineral resources of southern Nevada One volume: Mining districts and mineral resources of Nevada, by F C. Lincoln (1923), $1.50.

Jan 1, 1933

By Jack A. Crichton, Henry J. Gruy

This paper discusses methods used in the estimation of natural gas reserves and the general conditions under which the various methods are applicable. The factors used in estimating natural gas reserves are reviewed. Errors which have been found to occur frequently are listed. Introduction The estimation of natural gas reserves has become of paramount interest because of the increasing importance of gas in the nation's economy. Gas is a most desirable fuel, a fact substantiated by the continued rise in the market demand. In addition, new uses for gas are being developed by the chemical, plastic, and associated industries, and plants are being built to make gasoline from natural gas. These are a few of the factors contributing to the importance of the nation's natural gas reserves. With the increased importance of gas there is an increase in the need for reliable estimates of the magnitude and availability of natural gas reserves. These estimates are being used currently: (I) to determine which fields contain sufficient available reserves to justify the construction of pipe-line outlets to serve particular markets; (2) to design pipe lines necessary to serve those fields adequately;] (3) to determine the location of industrial and chemical plants; (4) to finance the development of gas properties, and the construction of gas pipe lines; (5) to determine fair and adequate depletion allowances and depreciation rates; (6) to justify applications for gas pipe lines before various regulatory bodies; (7) to determine the number of wells required to exploit the reserves most economically; (8) to aid in establishing values for the purchase or sale of gas properties, and for purposes of inheritance taxes; (9) to determine equities under unitized operations; (10) to provide a basis for calculating the economics of gas-cycling operations. History or Estimation of Natural Gas Reserves The natural gas industry in the United States had its beginning during 1826 when natural gas was used for lighting the city of Fredonia, N. Y. The first natural gas pipe line was a 25-mi]le wooden line constructed from hollowed logs, connecting West Bloomfield and Rochester, N. Y. There is no record of an attempt to estimate the gas reserve at West Bloomfield but an attempt was made to determine the capacity of the well by measuring the time required to 611 a large balloon. One of the earlier publications concerning estimation of natural gas reserves is the "Manual for the Oil and Gas Industry," published by the Treasury Department, United States Internal Revenue, in i9i9. The following methods of computing "gas depletion" are listed: (I) production decline of the gas well or property; (2) decline in open-flow capacity; (3) comparison with the life history of similar wells or properties, particularly those exhausted Art

Jan 1, 1949

By E. W. Schilling

THE separation of hematite by hysteretic repulsion was first brought to the attention of the public in 1922, by W. M. Mordey1. Three years later another paper2 was published and after another four years a third paper3 appeared in the South African publications. Certain data were lacking in these papers. In order to continue the work intelligently a knowledge of the shapes of the hysteresis curves for certain minerals was very necessary. This information was not available until the present year4. It was known that reduction of certain ores rendered them amenable to this process of separation but definite data in the form of curves showing exactly the effect of such treatment were lacking. Prob-ably our best source of information on the separation of minerals by the use of alternating-current magnetic fields today is the reports from the U. S. Bureau of Mines 5-7. It is not the purpose of this paper to tell the reader in detail how to make a commercial separator. Experimental models have recently been made 7 and the results obtained have been so good that it is the opinion of the authors that the public will soon take an active interest in the subject and its development. The writers have constructed a separator that is considerably different in construction and operation from the two types described by Mr. Davis. This will be described, but the real purpose of this paper is to outline certain experiments and give curves showing data that have a fundamental bearing upon the practical construction of a separator of this type.

Jan 1, 1935

By R. Schumann

THE expression "unit process " comes up with increasing frequency in discussions among metallurgists and mineral engineers, especially among those concerned with training the next generation. The unit process approach characterizes a significant advance along the road from metallurgy as an empirical art to metallurgy as a branch of engineering. The purposes of this paper are to define and list the unit processes in specific terms, to indicate the scientific and engineering principles basic to all the unit processes, and finally to show how these ideas have been applied to a reorganization of instruction in chemical metallurgy. UNIT OPERATIONS AND UNIT PROCESSES Metals are extracted from ores and other raw materials by stepwise procedures. In general, each metallic element is extracted by a different procedure. For many of the metals there is a choice of several flowsheets. However, the procedures all have steps in common. In fact, the many different flowsheets are all made up of a relatively small number of steps which are combined in different groups and sequences. For example, crushing, screening, roasting, sintering, melting, and gaseous reduction are steps which each appear in the flowsheets for extracting the majority of the metals. The individual steps or flowsheet units can be designated as unit operations or unit processes. These terms are well established in the field of chemical engineering, as the American Institute of Chemical Engineers' definition of chemical engineering shows: " Chemical engineering is that branch of engineering concerned with the development and application of manufacturing processes in which chemical or certain physical changes of materials are involved. These processes may usually be resolved into a coordinated series of unit physical operations and unit chemical processes. The work of the chemical engineer is concerned primarily with the design, construction, and operation of equipment and plants in which these unit operations and processes are applied. Chemistry, physics, and mathematics are the underlying sciences of chemical engineering, and economics its guide in practice."1a In this definition, the distinction between unit operations and unit processes is that the unit operations are physical while the unit processes are chemical. Table I gives a list of the principal unit operations and unit processes of chemical engineering, taken from Shreve. lb Table 2 lists the principal unit operations and unit processes used for metal extraction. The division between unit operations and unit processes is similar to the chemical engineers' distinction and also corresponds approximately to the division of labor between mineral dressing and chemical metallurgy which has been customary in the past. Furthermore, it will be noted that in the proposed classification the unit processes primarily involve chemical reactions and/or changes in state of aggregation; the unit operations, primarily do not involve either bulk

Jan 1, 1948

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1693 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists It Broadway New York 4, N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs and Mine Management 156, Ataturk Bulvari-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 8 Howard-Canfleld Bldg. Santa Barbara, Calif. COWIN & CO. Mining Engineers and Contractors Consulting Shaft & Slope Sinking Appraisal Mine Development Reports Mine Plant Construction I-lath St. S. W. B'ham, Ala., Phone 56-5566 MILTON H. FIES Consulting Engineer Rooms 1201-2. Albama Power Co. Bldg. Birmingham, Alabama]

Jan 1, 1952

By W. W. Scott

The application of engineering methods to the problems connected with drilling and producing in the oil industry has led to the development of the science that is variously termed "petroleum engineering," "production engineering," "petroleum production engineering," and even Itpolitical engineering." It would require much detail to enumerate the qualifications of a petroleum engineer, just as it would for an engineer in any major industry. For those who have a genuine liking for the oil industry, there is a wide selection of pathways to achievement. The oil industry is now highly specialized. Its products are necessary to all civilized people and are indispensable in the security of our nation and also in the well-being of our families. The business structure of our country depends in a large measure upon oil, and the welfare of this group as individuals is certainly linked with the welfare of the oil industry. What Is the Trend of Engineering? The oil industry offers a fertile field of opportunity for engineering; probably more so than any other industry. The sciences of geology, physics, chemistry and mathematics are all used in some phase of the oil industry and to a very considerable extent in the production division, which embraces the geological, drilling and producing departments. In drilling and production alone, research programs of considerable magnitude are being carried on at this time, and no doubt the future will see a great deal more of this kind of work. Through the cooperation of the engineer, the equipment manufacturer, and the American Petroleum Institute, immense savings have been made by the standardization of drilling and production equipment. Drilling equipment in itself offers a wide scope for study, in that continued efforts are being made to improve the equipment so that it can be made to drill faster and to greater depths. The improvements in drilling equipment are required because new reserves of oil are being found at progressively greater depths. In order to produce such oil in competition with oil now being produced from reservoirs

Jan 1, 1937

By B. A. Eaton

The subject of many discussions and technical papers in the last 20 years has been the prediction of the well-bore pressure gradients that are required to induce or extend fractures in subsurface formations. The subject merits this attention because of the frequently recurring problems that arise from an inability to predict fracture pressure gradients. Encountered in several common types of operations in the oil industry are problems associated with the prediction of formation fracture pressure gradients. When wells are being drilled in both new and old fields, lost circulation is often a very troublesome and expensive problem. Complete loss of circulation has been disastrous in some cases. Many times, such disasters could have been avoided if techniques for calculating fracture pressure gradient had been employed in the well plans, and if casing strings had been set, and mud weight plans had been followed accordingly. In areas of abnormally pressured formations, the prediction of fracture gradients during the well-planning stage is extremely important. In fact, it is as important as the prediction of formation pressure gradients, which has received a great deal of attention in recent years. There are several published methods used to determine fracture pressure gradients. However, none of these methods appears to be general enough to be used with much reliability in all areas. In 1957, Hub-bert and Willis published a classical paper that included the development of an equation used to predict the fracture extension pressure gradient in areas of incipient normal fau1ting.l Overburden stress gradient, formation pore pressure gradient and Poisson's ratio of rocks were the independent variables that were shown to control fracture pressure gradient, the dependent variable. In 1967, Matthews and Kelly published another fracture pressure gradient equation that is different from that of Hubbert and Willis in that a variable "matrix stress coefficient" concept was utilized.3 Later the same year, Costley wrote about a similar idea.5 Goldsmith and Wilson used a least-squares curve-fitting technique and field data from the Gulf Coast area to correlate fracture pressure gradient with formation pore pressure gradient and formation depth.' They noted that the fracture pressure gradient increased with increasing depth while the pore pressure gradient remained constant. In each of these cases, the problem for which a solution was sought was to determine the bottom-hole pressure gradient required to initiate or extend a fracture. Results of the previous work show that fracture pressure gradient is a function primarily of overburden stress gradient, pore pressure gradient, and the ratio of horizontal to vertical stress. There is argument for a fourth variable in that in many cases breakdown fracture pressure gradient is greater than the fracture extension pressure gradient. However, if the fracturing fluid is able to penetrate the formation through the pores or existing cracks, there is very little

Jan 1, 1970