Search Documents

By R. P. Abendroth

This study is concerned with the kinetics of selective oxidation of chromium in a commercial Fe-Cr-Ni alloy. Selective oxidation of chromium in this alloy, by use of a low oxygen-potential atmosphere, leads to the formation of a compact, protective layer of Cr2O3. This layer serves to protect this alloy from gross scaling when it is subsequently exposed to severe oxidizing conditions at high temperature. The interaction of low oxygen-potential atmospheres close to equilibrium with Fe-Cr and Ni-Cr alloys has been studied by others."' These studies werk concerned with the surface-structure variations under slightly oxidizing conditions. NO detailed study was made of the oxide scale formation kinetics, however. The alloy samples were cut from 0.012-in.-thick sheet, with an apparent surface area of 7.1 sq cm. These sheet samples were abraded through 4/0 metallographic paper, and washed in alcohol and acetone. The analysis of the sheet alloy is (in weight percent): 42 pct Ni, 5.5 pct Cr, 0.09 pct C, 0.18 pct Al, 0.36 pct Si, 0.26 pct Mn, balance Fe. The weight gain vs time data were obtained with a 2-g capacity fused-silica spring—cathetometer system. The spring deflection was optically magnified ten times before being read by the cathetometer. A sensitivity of about 0.01 mg was attainable. The spring was enclosed in a water jacket maintained at 60°C to minimize the effect of temperature changes. The sample was suspended from the spring with a fused-silica hangdown and was positioned in the thermal center of a mullite furnace tube. Sample temperature was read with the aid of a thermocouple placed outside the mullite tube and an inside vs outside temperature calibration. Temperature change during the course of a run was ±0.25°C, with a temperature gradient of less than l.O°C over the length of the sample. Total temperature uncertainty was no more than ±3.0°C. Alignment difficulties between the hangdown and radiation shields in the furnace tube required that the sample be positioned in the furnace when cold, and heated with the furnace until the temperature stabilized at the desired point. This required 5 to 6 hr, and was carried out in Matheson ultrahigh-purity hydrogen. Oxidation was started, after evacuation, by introducing a hydrogen-water vapor mixture, obtained by saturating hydrogen with water vapor at 31.00o ± 0.02oC. Oxidation was continued for 90 min. Gas flow was 300 ml per min during heat up and oxidation. Since only several milligrams of oxide are formed on each sample, chemical analysis of the oxide is difficult. A representative analysis is: 80 pct Cr2O3, 5 pct Fe2O3, 3 pct Al2O3, 4 pct MnO, 7 pct SiO2, 1 pct or less NiO. X-ray diffraction analysis of the oxide as formed on the alloy gives rhombohedra1 Cr2O3, and barely distinguishable amounts of a cubic spinel phase, and possibly AlZOs and SO2. The identification of these latter two compounds is by no means certain. The spinel phase could be based on iron or manganese as these elements are present in significant amounts in the oxide. The results of the kinetic studies using 31°C dew-point hydrogen-water vapor mixtures were found to conform to a parabolic rate law. In many cases the parabolic plot consisted of two intersecting straight lines, defining an early and a late rate for a particular run, and in the other cases the parabolic plot consisted of one straight line for the entire run. The slopes of the various straight lines were determined by the method of least squares. Reproducibility of the data was good enough for multiple runs at the same temperature such that the value given for the rate constant is the average for two or more closely similar values, rather than widely varying values of the rate, where more than one determination is indicated in Table I. The exhibition of only one or of two rate constants during a run can happen at the same temperature. Thus, Table I shows that at 11'74°C a single rate constant was obtained from one sample, while other samples oxidized at the same temperature gave an early and a late rate constant. It should be noted that the single rate constant corresponds very closely with the early rate constant. This is also true at 1153°C. The time at which the late rate started to appear was variable, usually occurring 20 to 40 min after oxidation had started.

Jan 1, 1964

By Rebecca Mae Summer

Increasing urbanization and industrial activity require increased supplies of sand and gravel. This means expanded surface mining and despoiled land near population centers. Highly competitive land use demands justify serious consideration of premining planning for multiple land use and reclamation concurrent with mining, 1-5 Formulating solutions to environmentally and economically sound uses requires a comprehensive approach based on properties of the natural resource base--geology, soils, and water. A study of sand and gravel mining within Pleistocene-Holocene fluvial deposits in Colorado County, Texas (Fig. I) illustrates how physical limitations imposed by the resource base are determined.6,7 Data from drillers logs of water wells, test boreholes, field observations, and laboratory analyses are used to evaluate these physical controls.

Jan 1, 1978

By S. S. Solomons, V. H. Tillmann, L. Smaniotto

INTRODUCTION The Zinc Corporation, Limited and New Broken Hill Consolidated Limited (ZC/NBHC) mines are situated at Broken Hill, New South Wales, Australia (refer Fig. 1). Both companies are wholly owned subsidiaries of Australian Mining and Smelting Limited (AM&S). Annual production from both mines is 2.3 million tonnes of lead, silver and zinc ore mined by a variety of underground methods. From 1911 to 1968, conventional overhand cut and fill stoping (both open and square set timber) was used almost exclusively, though some trials with shrinkage and sublevel stoping were undertaken. The trial stopes used short holes in conparison with today's sublevel open stopes. Mechanised cut and fill methods with regular rockbolt support were introduced in the early 1960's and undercut and fill stoping replaced square set timber stoping for pillar extraction in the late 1960's. Since 1968, increasing emphasis has been placed on longhole open stoping (LHOS) although some areas of the orebodies are comrnrnitted to the abovemehtioned methods since existing stope development makes it impracticable to change. In 1979, approximately half the total production was mined by LHDS and it is expected that the LHOS proportion will increase in the future. A vertical crater retreat method of longhole mining has also been successfully introduced to replace the undercut and fill stoping of some pillars and it is expected that this stoping method will be used in some future primary ore extraction. This paper reviews the progress of LHOS technology at ZC/NBHC with emphasis on the stope planning and design process and the importance of rock mechanics applications. The objective has been to maximise the primary extraction of the orebody giving due consideration to stability and safety. This has led to the design of a novel sloped wall longhole stoping method which should eliminate the formation of pillars by mining the orebody in a "continuous" manner incorporating a sloped sand interface between the blocks of ore being mined and the previously mined sandfilled stope. The expected results include the complete extract of the orebody without the formation of pillars and with minimal dilution of ore with sandfill. The evolution of the method can be best illustrated by following the mining progress of the relatively new Southern 'B1 Lode orebody at the NBHC mine. GEOLOGY Southern '8' Lode is the southern extension of the 'Bt Lode orebody, which is currently being mined further to the north in ZC/NBHC (refer Fig. 2). The ore block being developed and stoped extends for a vertical height of 90 metres from No. 17 level down to approximately ten metres above No. 19 level. The ore minerals are sphalerite and galena with the zinc:lead ratio averaging approximately 3:l with a minor amount of silver associated with the galena. There is a sharp contact between the ore and the country rock on the footwall and keel, while the hanging wall gradates into medium and low grade material. The gangue is primarily quartz together with garnet, biotite, feldspar, gahnite, sericite and minor apatite. In various horizons within the orebody, grey feldspar, quartz and garnet pegmatites occur as stratiform layers. The ore and country rock are competent with some inconpetent boundaries.

Jan 1, 1981

By R. E. Zimmerman

WITH coal-preparation plants becoming more complex and containing widely diversified types of equipment and processes, it is necessary that considerable control be exercised in their operation. Rising mine costs make it imperative that close check be made of plant efficiencies to assure a minimum loss of coal to the refuse bank. Further, much of the coal sold today is sold on a competitive specification basis, and this makes it necessary to provide frequent analyses and inspections. Many ' plants are required to operate on a two or three-shift basis, and as a con- sequence an efficient organization is required to eliminate down time and provide for smooth low-cost operation. ORGANIZATION Probably the most important item for successful operation of a preparation plant is a capable, properly organized staff, with the individual workers properly informed and well trained for their particular jobs, clear-cut lines of authority among the supervisors and in general a standard operating procedure for most conceivable conditions that may occur. The idea of placing the older, partially disabled and generally incompetent coal miner in the cleaning plant, as was the practice on the earlier tipples, is entirely inadequate in a modern complex cleaning plant. The new plants require intelligent, alert, and reasonably educated men. With perhaps millions of dollars invested in an installation, it is poor business to use other than a well organized, well trained, and properly supervised force. Organizations naturally must vary with the size of the plant and local conditions; whether it is a central cleaning plant at a distance from the mine organization or one of several cleaning plants operated by the company. Smaller operations can be operated by a washery foreman, under the supervision of the mine superintendent or perhaps the "outside" superintendent. Large installations should have a plant superintendent either responsible to the mine superintendent or preferably, where possible, responsible to a preparation manager or engineer. A typical organization chart for companies operating in the anthracite region of Pennsylvania is shown in Fig. 1. Breaker (preparation plant)

Jan 1, 1950

By L. S. Panyity

The question of natural-gas supply is receiving careful consideration in many parts of the country, as in the winter months it is quite a problem to have on hand sufficient gas to satisfy the demand. Increasing the output of wells by the application of vacuum has been tried with various results and large companies have attempted to keep up the supply with gas compressors. The possibility of storing natural gas in the sands of exhausted gas pools has been tried in a few instances with satisfactory results. This method may prove of practical value in solving the problem, especially in the case of towns that formerly obtained gas from their immediate vicinity, but now must search for new pools. Town Plant Regulator High Pressure Line Exhausted Gas Field used for Storage Producing Gas Field FIG. 1. In all cases, only part of the available supply is utilized during the warns weather, so that many wells are shut-in, yet during the winter months, the supply is not sufficient even with all the wells on the line; in such cases it would be of great value if a large volume of stored gas were on hand, obtained through wells that would have been standing idle during the summer.

Jan 1, 1919

Discussion of the paper of EDGAR L. NEWHOUSE, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin: No. 92, August, 1914, pp. 1801 to. 1806. G. C. RIDDELL, East Helena, Mont.-As nearly as I can recall at the present moment, there are only four or five large plants on the continent where the lead on charge is carried in the neighborhood of 40 per cent. These are at Herculaneum, Collinsville, and Federal, Ill.; Trail, B.. C.; and East Helena, Mont. Our object at the latter point is to smelt a maximum amount of Coeur d'Alêne lead sulphides in as compact and self-fluxing a charge as possible, and to this end we are now smelting a mixture that at times carries up to 42 per cent. lead. The monotony of producing the 7,000 tons of bullion shipped each month to. the Omaha and Chicago refineries is relieved somewhat by the fact that the 15,000 tons monthly of Coeur d'Alêne ores that are com-ing to us carry enough zinc to provide the one-half slag used with from 6.5 to 7.5 per cent. zinc clay after day. During the month of March, 1914, three lead furnaces in continous operation, each 136 in. long, averaged 249 tons per furnace clay, exclusive of coke and slag shells, which is smelting at the rate of 5.5 tons per square foot of tuyère area. The

Jan 11, 1914

Jan 1, 1968

By Rana P. Singh

Electrolytic metal reduction operatios in both aqueous and molten salt electrolytes are being studied by digital signal analysis. The purpose is to determine the relationship between the physical processes occurring in the cell and the frequency spectrum of the cell's fluctuating electrical parameters. The fast Fourier transform of cell voltage (in galvanostatic operations) or cell current (in potentiostatic operations) is computed on-line in real time for the electrorefining of zinc in aqueous acid chloride solutions.

Jan 1, 1984

AN indication that Mesabi Range iron use companies may develop their own flotation processes for low grade iron ores is the report that Cleveland Cliffs Iron Co. is adopting a variation of one of the oldest known methods at its new Michigan treatment plant. Basically, the method involves using fatty acids and fuel oil reagents. The idea was developed many years ago and should be free of patent control. With other laboratories working on the same tack, it seems to be a pretty good bet that they will come up with their own processes. Any outside process will have to offer considerable advantage or low royalty rate to get consideration. Much of the appeal of the fatty acid process is the cheapness of the reagent. One source is pulp paper liquor in semi-refined form. With stream pollution legislation acting as a strong pressure, paper companies have been seeking ways to dispose of the material. Wisconsin has even attempted to use it for road binder.

Jan 5, 1953

By Jerome F. Kuzmick

The use of iron powder during the postwar conversion period has been increasing with great rapidity. This is particularly true in regard to the manufacture of molded mechanical parts such as bushings, gears, cams, small wheels, and the like. Many manufacturers have found it possible to replace machined cast iron and carbon steel with molded iron powder parts, and thereby can not only effect a savings in cost, but can produce a better product as well. As the field of application for iron powder parts widens, greater demands are made upon the powder supplier concerning quality and uniformity characteristics. The following are some of the most important properties parts fabricators desire in the iron powder they use: 1. The powder should have high compressibility so that good density can be obtained without the use of excessive pressures. At the same time, it should show low die wear so that a large number of pieces can be produced from the die. This means that the powder must be of high purity and good softness or plasticity. 2. The powder should produce compacts of high green strength, so that unsintered parts can be handled without breakage or fraying of the edges. 3. The sintering properties should be good so that satisfactory strength is obtained in the sintered piece. 4. Compacts made from the powder should show small but, above all, uniform dimensional changes during the sintering operation so that accurate parts can be produced, and warping and other such bad effects eliminated. 5. The powder should have satisfactory flow properties for automatic molding. 6. It is very important that the powder be uniform in sieve analysis, compressibility, flow, purity, and other qualities, from container to container in any given lot and from shipment to shipment. 7. Price—The fabricators desire all these good properties, but in many instances still do not wish to pay a premium price. There has been considerable discussion as to the importance of price of the powder in relation to the cost of the finished product. It is true that in cases where certain special properties only procured by powder metallurgy are required, price is not a criterion. On the other hand, there have been a number of applications recently made which would not be commercially practical with a powder which commands a premium in price. Iron powder parts are compressed in automatic presses to definite size, shape, and density. The powder is compressed to a density figure dependent upon the function the part is to perform, as well as upon such important considerations as press capacity and die wear. Such parts can be roughly broken down into the following density ranges:

Jan 1, 1949

By M. F. Werneke, J. A. Jones

Abstract- The use of a unique class of sulfhydryl collectors, the monoalkyldithiocarbamate salts ([RNHCS]) as direct collectors for malachite and azurite is presented. Microflotation and laboratory scale flotation tests were performed to define the collector properties of these reagents under a variety of flotation conditions. On the basis of the results, it is proposed that some property of the amine-hydrogen atom in the reagent has a significant influence on the unusual activity of these collectors for oxide copper minerals.

Jan 1, 1978

By H. L. Hopkins, OHIO, L. W. Kemph, CLEVEL AND, E. V. Ivanso

A balanced system of internal stress is set up in any metallic structure by plastic deformation below the annealing temperature. The internaI stress induced by cold rolling or other fabricating processes is generally recognized and its magnitude is known to be, within certain limits, a function of the degree of cold deformation. The plastic deformation that may accompany rapid cooling from elevated temperatures may not materially change the form of the product. The internal stresses so induced are not, therefore, so evident and nonrecognition of their presence has at times led to engineering failures. The heat treatment of aluminum alloys is a relatively new art and little information is available regarding the magnitude of stresses induced during the commercial heat treatment of aluminum alloy products. As the industrial use of aluminum increases, it is inevitable that products of increasingly large volume will be required. It has become necessary in the present commercial utilization of aluminum to heat-treat castings and forgings weighing hundreds of pounds. One of the factors governing the magnitude of internal stresses arising from rapid cooling from elevated temperatures is that of the size of the structure being treated. Some of the other factors are: cooling rate, elastic properties of the alloy, thermal expansivity, thermal conductivity, and the presence or absence of phase changes. Practically all aluminum alloys have a high coefficient of thermal expansion and some are capable of developing relatively high elastic limits. On the other hand, all commercial aluminum alloys have relatively high thermal conductivities, no invariant phase changes, and the quenching temperatures are comparatively low. In the absence of invariant phase changes involving change in the type of crystallographic lattice, the fundamental basis for the development of internal stress

Jan 1, 1934

By Edgar Shepard

THE interest of the Federal Government in improvement of water-ways dates from 1820, when Congress appropriated $5000 for making a survey of the Mississippi and Ohio Rivers and assigned this work to the Corps of Engineers of the Army. Since that time the Government has gradually assumed increasing jurisdiction in the matter of improvement and control of inland waterways until, by the River and Harbor Act of Jan. 21, 1927, Congress assigned to the Secretary of War and to the Chief of Engineers the duty of making surveys, in accordance with House Document No. 308, 69th Congress, to formulate plans for the most effective improvement of the navigable streams of the United States and their tributaries, for navigation, development of water power, control of floods, and the needs of irrigation. Virtually all the preliminary investi-gations and surveys required by this act have been completed. The reports made to Congress have been published and often are referred to as "308 Reports." The map shown in Fig. 1 is merely a skeleton distribution of the projects covered by these reports, but it serves to indicate the magnitude of the proposed undertaking. In many instances, a single character on the map stands for a major development involving several dams and reservoirs or many miles of canals or levees. The devastating floods of 1936, and the need for worthy public works to take up the slack in employment, gave further impetus to this program and in 1936 led to the enactment of a bill authorizing a large number of these projects.

Jan 1, 1940

Jan 1, 1906

By Donald N. Rosenblatt

I would like to commend the author on his description of Pinto Valley's plant, and its interesting innovations. The author's discussion of 18 ft in diameter by 21 ft long primary ball mills (the largest wet ball mills made to date) is of considerable importance to those who have been engaged in the field of studying ball mill liner wear as it relates to various grinding installations. While it is stated that the mills have operated on a fixed tonnage and therefore it has been difficult to determine the best liner pattern, calculations from the data in the paper indicates that for mills 1, 2, 5, and 6, the tonnage per hour varies from a low of 223 for mill No. 1, up to a high of 314, for mill No. 2, while mills 5 and 6 calculate 285 and 246, respectively. Analysis of the wear patterns for the single wave liners used in mill No. 1 as compared to the double wave liners in mill No. 2, suggests that the author's data may tell more than he suspects about liner wear to be expected and thus what should be a best pattern selection from what may appear to be only limited hours of operation. [Fig. A] is a reproduction of author's [Fig. 10], to which wear forecast patterns [F-1 and F-2] have been added. Forecasts are based on many previous studies of large diameter ball mill operations over many years of field service. Calculations from the first-wear pattern provide an initial wear rate of only 13 lb of liner per 100 sq ft of shell liner surface per day, or 0.031 lb per to: ground. However, the second wear pattern is ac-

Jan 1, 1978

By P. F. Gnirk

Consideration is given to creater formation with shallow, contained, chemical explosions in rock masses which exhibit different inherent physical and mechanical properties as determined by standard laboratory techniques. The primary purpose is to determine whether or not a simple but useful generalized correlation can be established between explosive crater formation and one or more common rock properties. Such a correlation could be beneficial in predicting with some degree of reliability the size of a crater which could be expected in a particular rock type for a given input of explosive energy. A series of crater formation experiments employing constant weight charges of Gelex 2 explosive was conducted in five submembers of the taconite formation at the eastern end of the Mesabi Range in northeastern Minnesota. Five mechanical and physical properties-unconfined tensile and compressive strengths, Young's modulus of elasticity, longitudinal wave velocity, and density-were determined by conventional laboratory techniques using core samples from the taconite submembers. Although insufficient data were obtained to warrant the use of mathematical methods in the determination of empirical relationships, the results provided a fairly strong indication that with an increase in magnitude of any one of the five rock properties definite decreases in the optimum crater volume and surface area occur. Furthermore, for a constant explosive energy input, the presence of bedding planes and joint systems in a rock mass influences the formation of craters in such a manner as to increase the volume of rock broken substantially above that expected from the same rock mass without joint systems and, in particular, without bedding planes.

Jan 1, 1968

By John T. Norton, Matthew J. Donachie

Residual lattice strai?zs were produced in 2024 aluminum and ingot iron by uniaxial tensile deformation. These strains were rneasured on the original surface and ulith depth below the surface. The strains conformed approximately to those from a macroscopic stress distribution but they were not truly macroscopic in nature. The exact mechanism which apparently causes the coherently difi9,acting region of each grain to behave as if macroscopically stressed was not determined. MACROSCOPIC stresses in metals produce strains in the lattice which result in X-ray line broadening and line displacements. The latter effect can be utilized in a technique for determining stresses in metals as first shown by Lester and born.' Subsequent advances in technique have enabled the X-ray method of stress measurement to be satisfactorily applied to many problems involving residual stresses of a macroscopic nature, such as those due to welding, grinding, shot-peening, and so forth. In the case of stresses such as those described above, the correlation of X-ray- and mechanically determined data has been generally good. However, plastically extended polycrystalline metals have sometimes been reported2 to show line displacements upon release of the applied tensile load, yet the nature or origin of the residual lattice strains, rls, producing these displacements has never been clear. As will be pointed out, this lack of clarity regarding the macroscopic or microscopic nature and origin of these stresses casts doubt on the validity of results achieved by the commonly accepted techniques of X-ray stress measurement. This anomalous behavior requires clarification to remove the doubts concerning X-ray stress measurement. The present paper is the result of an investigation of the interesting behavior of such plastically extended polycrystalline metal bodies. The studies were originated to carry out the following tasks: 1) Observe whether a residual lattice strain is produced as a result of plastic extension and show whether any residual lattice strains produced can be related to the usual concept of a macrostress. 2) Examine the origin of any residual lattice strains observed. 3) Consider the implications or consequences of the existence of such residual lattice strains on the problem of X-ray stress measurement. THEORY 1) Lattice Strains. The theoretical developments necessary for the treatment of lattice strains and their relation to stresses follow from the classical theory of elasticity and have been adequately covered by arrett. For an isotropic solid under homogeneous deformation, it can be shown that, for uniaxial stresses where Dl is the macrostress acting in the longitudinal direction; E$L is the lattice strain in the plane defined by the surface normal and the longitudinal direction at an angle, , from the surface normal; ET is the similar strain in the transverse plane; E is Young's modulus; and v is Poisson's ratio. Eq. [2] is independent of angle + and Eq. [I] is a linear function of sin2, see Fig. 1, and can be solved analytically for DL if E and u are known and EL is measured. Thus, a uniaxial macrostress will be indicated by a linear E,L vs sinZ plot and a

Jan 1, 1962

By H. R. Steacy, A. H. Lang

Growth of general interest in uranium during the last ten years has been unparalleled in mining history, outranking the popular gold rushes and mining booms of bygone years. This is not surprising, considering the spectacular advances in nuclear research and the fact that a small amount of uranium can provide great quantities of energy for peaceful purposes. There are, however, a number of misconceptions and exaggerations regarding uranium. Many novices have highly exaggerated ideas of the ease of finding workable deposits, as opposed to mere occurrences, and reports of insignificant discoveries are sometimes given much publicity. Beginning about ten years ago mining for uranium has assumed a major place in Canadian and U. S. mineral industries. Uranium is now high on the list of metals produced in Canada. The gross value of uranium production in Canada in 1958, when additional plants now under construction are operating, will probably exceed 180 million dollars.

Jun 1, 1956

By Lewis A. Riley

I desire to submit, for the consideration and information of the members of the Institute, the following data, drawings, and tables, showing what I believe will be interesting information with regard to the diamond drill, and its uses in developing mineral lands. I would first say that the results given have been obtained during the past two years by means of two drilling machines belonging to the Lehigh Valley Coal Company, operating on their coal lands in the Mahanoy, Lehigh, and Wyoming regions. 1st. A tabulated statement, giving location of borings, date, progress, total cost, itemized cost per foot, etc. 2d. Section showing strata bored in Nos. 5 and 10 holes at Mt. Carmel, see Plate VI. 3d. Section showing strata bored in No. 19 hole at Hazleton, see Plate VI. 4th. Photograph and description of drill No. 2. From the first it will be seen that the total number of test-holes bored up to May 1st of this year is 24; 9 of these are in the Mahanoy region, 6 in the Lehigh region, and 10 in the Wyoming region, in all of which cores have been taken for the whole distance. The total distance bored is 9902 feet. The majority of the holes have been put down for the purpose of proving the lower veins of the coal series, and have had to encounter the harder rocks of the coal formation. Much of the distance has been through the lower conglomerates, going in some cases through the coarse egg conglomerate, the foundation of the coal deposit, and to the green sandstone and red shale which underlie it. These lower sandrocks and conglomerates are among the hardest known to geologists, and present a formidable resistance to the exploring drill. This fact must be taken into consideratiotl in comparisons of cost of drilling, and when considered will still further improve the very favorable results I am able to show in my statement of costs. In illustration, I will cite the work of one bit when boring in the upper or softer rocks of the Wyoming region, where 280 feet were obtained without resetting, while in the Lehigh and Mahanoy regions, in the lower and harder rocks, bits set with the same quality of diamonds would only bore from 3 to 20 feet before being worn out. In this connection it may

By Nicholas J. Grant, W. Michael Yim

The creep-rupture properties of nickel, in as-prestrained or prestrain-polygonized condition, were studied at 1300°F and 4000 psi, and also at 700°F and 26,000 psi. An improvement of strength was noted in both the as -prestrained and the prestrain-polygonized tests at each temperature. The as-prestrained tests, however, showed superior creep resistance to the prestrain-polygonized ones. From the results of X-ray and etch-pit studies, the strengthc gain was interpreted in terms of dislocation density and the stability of preformed substructures. COLD work is known to improve the strength properties of metals at low temperatures. At high temperatures, however, the strength improvement is often lost if gross structural changes, such as re-crystallization, take place prior to or during the test. Even in the absence of recrystallization, a prestrained metal may undergo structural changes— polygonization and the formation of well-defined subgrains—which importantly effect the resultant properties. The relationship between substructure and creep properties has received considerable attention in recent years. The work of wood1 indicated that the creep strength of aluminum and its alloys was closely related to the subgrain size. Hazlett and Hansen,2 and Ancker, Hazlett, and parker,3 working with nickel and nickel alloys, had shown that small amounts of prestrain at room temperature followed by a recovery anneal at 800°C (1470°F) improved the strength at both low and high temperatures. The strength gain was attributed to an increase in the number of subgrain boundaries as a result of the prestrain-polygonization treatment. More recently Coldren and Freeman4 studied the effect of substructures on the creep rate of nickel at 1550°F. Their conclusions indicated that the substructure size as measured by the number of boundaries was the factor that controlled the creep rate. In addition, the perfection of the subgrain boundary has been indicated to have an important role on the strength.' On the other hand, there are data which disagree with the above observations. Grant, Chaudhuri, Silver, and Ganow6 found no creep strength improvement by a prestraining treatment. In reviewing the role of subgrains on high-temperature creep, Shepard and Dorn7 concluded that the contribution of the subgrains to high-temperature creep strength was a minor one. Guard,8 in a recent study on poly-gonized nickel, has cast doubt on the validity of the postulate that subgrain size controls the creep rate. In the majority of the previous studies, the subgrain boundaries have been singled out as the most important factor in determining creep strength; however, there is no firm theoretical ground for the postulate that the subgrain boundaries act as effective barriers to dislocation motion.B910 Little effort has been directed toward the study of the relationship between creep strength and other structural variables, such as dislocation density, lattice strain,

Jan 1, 1963