Search Documents

By J. H. Lightfoot, Stuart E. Buckley

DEEP drilling has led to the development of numerous pools which yield products consisting predominantly of natural gas accompanied by high-gravity water-white or slightly straw-colored liquid. Yields of this "condensate" or "distillate," as it is commonly called, vary from traces to over a hundred barrels per million cubic feet of gas. The fact that this liquid exists in the reservoir as an integral part of the gas phase and is formed by condensation attending simultaneous reduction of pressure and temperature after its entry into the well was apparently first recognized about 1932.1 The nature of the physical phenomena involved in this condensation was clarified for the petroleum industry in 1933 by a report by Sage, Schaafsma, and Lacey2 of the results of an experimental investigation of the behavior of mixtures of methane and propane. Search of the literature has revealed that the condensation of liquid from gaseous mixtures by isothermal pressure reduction is not a new discovery. Kuenen was led by theoretical considerations to expect such a phenomenon, and in 1892 reported3 the results of experimental verification of his deductions. This was followed by a considerable amount of work on the phase relations of mixtures by Kuenen4,5,6 and by others,7,8 mostly in European universities. Since 1930 investigators in this country have reported experimental data on the properties and behavior of a number of hydrocarbon systems.9-17 It is now generally known that in the presence of natural gas the solubility in the gas phase of the heavier and normally liquid hydrocarbons increases rapidly with increasing pressure above 500 to 1000 lb. per sq. in. Thus, at pressures of 2500 lb. per sq. in. or higher a gas may contain appreciable quantities of hydrocarbons with normal boiling points as high as 600°F., which in turn may be condensed from the gas phase by the reduction of their solubility therein attending pressure reduction. The combined effects of pressure and temperature on condensation and vaporization of mixtures are most readily visualized by the study of phase diagrams. Since the construction, application, and interpretation of such diagrams have been described fully in readily available literature, 18-20 this paper will not review the theoretical aspects of this subject. While the behavior of gas-distillate systems is now clearly understood, at least in a qualitative way, most of the published work deals with the results of laboratory studies of binary systems or of synthetic mixtures of hydrocarbons, and although several systematic investigations of the effects of separator pressure and temperature on the yields of liquid product from gas-distillate wells have been made21.22 it appears that in all cases the limitations have precluded the construction of even approximately complete phase diagrams for naturally occurring systems. There has

Jan 1, 1941

By I. M. LeBaron

The phosphate ore, or matrix, is a mixture of white pebbles of phosphate, of all sizes but mostly minus I to 1 1/4-in. diameter, in a matrix that varies from nearly all silica-sand gangue to a mixture of pebble, sand and clay. There is an occasional streak of hard pan of sand cemented with iron oxide, which can be drilled without much difficulty.

Jan 1, 1948

Albin, B. R Billings, Mont. '28 Amster, Nathan L 25 Broad St., New York, N. Y. '28 Bache, Jules S 42 Broadway, New York, N. Y. '28 Barrett, C. P 5338 Harper Ave., Chicago, 111. '28 Bayless, William S Russ Bldg., San Francisco, Cal. '28 Bean, Louis, H 60 E. 42nd St., New York, N. Y. '28 Beatty, Ross J Room 604, 6 N. Clark St., Chicago, III. '28 Benwell, Oswald F Hold Mags. '28 Beymer, Albert S., V.P., Keystone National Bank Pittsburgh, Pa. '28 Blumenthal, Hugo 44 Pine St., New York, N. Y. '28 Boettcher. Charles Ideal Cement Bldg., Denver, Colo. '28 Bowlus, Thomas H., Banker, Pres., Allen County State Bank Iola, Ran. '28 Brown, Colvin B Chamber of Commerce, Washington, D. C. '28 Burt, Maxwell Struthers Southern Pines, N. C. '28

Jan 1, 1936

By G. S. Ansell, J. Weertman

The creep behavior of an aluminum alloy hardened with a finely dispersed phase of aluminum oxide was investigated. The as-extruded alloy shows an approximate steady-state creep in which the creed rate depends exponentially on the applied stress. The activation energy of creeb is abbroximately 150,000 cal per mole. The recrystallized alloy shows no steady-state creep. ONE method of improving the creep resistance of a metal is to introduce a finely dispersed second phase into the metal matrix. The improvement of the creep resistance has been qualitatively explained by assuming that the dispersed second-phase particles act as obstacles to dislocation motion. If the main effect of second-phase particles is simply to hinder dislocation motion then it is possible to derive a high-temperature creep equation for a dispersion-hardened alloy in a straightforward manner. In the Appendix of this paper such an equation is derived from a creep model which works very well for pure metals. Recently, F. V. Lenel has fabricated, for the first time, powder extrusions of aluminum-aluminum oxide in a large-grained recrystallized form. This alloy, designated as MD 2100, consists of a fine dispersion of aluminum oxide plates in a matrix of commercial purity aluminum. A considerable amount of investigation has been carried out concerning the microstructure and physical properties of this alloy.&apos; ) The aluminum oxide is present in the form of flakes 130A units thick and 0.3 u on edge. They are dispersed in the aluminum matrix with an average spacing of approximately 0.5 jx. The spacing varies in the range of 0.05 to 1.5 µ. The alloy structure is extremely stable at high temperatures. For this reason the alloy offers a unique opportunity for a fundamental study of creep of a very finely dispersed two-phase alloy. Lenel supplied specimens in both the unrecrystallized and recrystallized condition. This paper reports high-temperature creep experiments carried out on these specimens. The results obtained were rather unexpected. No steady-state creep was observed in the recrys-tallized material. In fact, after some transient creep which takes place upon loading, the creep rate is essentially zero ( < 10-8per min). If the second-phase particles acted solely as obstacles to the motion of dislocations, measurable steady-state creep would be expected. Since none is observed it appears that the main effect of the fine dispersion in the recrystallized material is to inactivate the dislocation sources themselves, rather than hinder the motion of dislocation loops created at these sources. EXPERIMENTAL DETAILS Specimens were tested in wire form, 0.087 in. in diam for the as-extruded alloy, and 0.035 in. in diam for the recrystallized alloy. These samples were held in friction-type wire grips; a gage length of 2.5 cm was used for all the creep tests. The specimens were held at 600°C in the test apparatus for at least 15 hr prior to each test. The tests were run under the condition of constant loading and, since the creep strains were small, can be considered as constant stress tests. The temperature of testing was held constant within 3°C. Elongations were measured with an optical cathetometer which was capable of measuring strains as smaIl as 0.00012. This allowed the measurement of strain rates as low as l0-8&apos;per rnin. In addition to the creep tests optical micrographs were made in order to determine both the grain size and microstructure of these materials. RESULTS Fig. 1 shows a few typical creep curves obtained from the as-extruded material. The elongations were somewhat erratic, but each curve shows a region of quasi-steady-state creep from which an approximate steady-state creep rate can be obtained. In general the higher the stress at a given temperature, the greater the total elongation before fracture. The lower the applied stress, the longer is the region where the creep rate is almost constant. Summary data from the creep tests of the as-extruded material are listed in Table I. The steady-state creep data of the as-extruded material for a range of stresses at a constant temperature follow a creep equation of the type creep rate = K&apos; = A exp (&) [11 where A and B are constants, k is Boltzmann&apos;s constant, T is the absolute temperature, and a the stress. The standard error of estimate of the data received is less than one order of magnitude. As shown in Fig. 2, if one compensates the creep-rate data for the effect of temperature over the range of test temperature, the steady-state creep data roughly follow a creep equation of the type Temperature compensated creep rate = K* = A exp

Jan 1, 1960

By H. D. Dahl, Roger C. Parsons

In order to improve roof stability, Continental Oil Co.&apos;s research program, initiated in 1969, was directed toward defining the geological parameters that affect the severity of roof conditions in any particular area of the mine. In addition, the program was seeking to define why roof falls in the Humphrey No. 7 mine (and in northern West Virginia-southwestern Pennsylvania coal mining areas) are oriented so that they occur primarily in north-south rooms or entries. Conclusions and recommendations from this study of roof fall orientation are given.

Jan 1, 1973

By J. C. Sullivan, W. A. Knoll

The sinking of a new shaft at the Newport mine, Ironwood, Mich., was started in May 1931 and completed on Aug. 3, 1932. During this period, 2665 ft. of shaft in granite was completed, at an average advance of 6 ft. per 24 hr. In Novernber of 1930, experimental work was conducted on 65 ft. of shaft through 22 ft. of overburden where ledge was encountered, and this work convinced the operators that all drilling could be done with vertical holes with the blasting relief to a 4½-in. hole drilled vertically in the center of the cut. The reason for not adopting the conventional V-cut was to get away from damaging the shaft steel. The blasting in a V-cut naturally tends to throw the broken material upward, but with the cut as adopted the relief was in a horizontal direction to a large extent. The scheme of mucking employed made it necessary to keep the steel shaft sets within 50 ft. of the bottom at all times. This could not be done without serious damage with a V-cut when blasting in granite. The cut as drilled also broke 10.83 ft. per round of drilling, which was considerably more than the experience with a V-cut in the same material. The extended cut reduced proportionately the delays for charging, blowing smoke and handling drilling equipment in the shaft. Another advantage was the ease in drilling vertical over inclined holes, and the preservation of the proper spacing of the drill holes at the bottom of the cut. Drilling Air was carried down the shaft in an 8-in. flanged pipe line at a pressure ranging from 95 to 100 Ib. This line was extended to within 100 ft. of the bottom, where a valve and a 4 by 4 by 6-ft. tee was connected to it. To each side of the tee was connected a nipple and elbow, the resulting span of the two elbows being about 4 ft. Lengths of short 3-in. hoses

Jan 1, 1940

By William C. Marshall, Frank G. Norris

The term "total operation" is meant to include problems that cannot be answered from the standpoint of either the blast furnace or the open hearth separately but must be studied by considering the interrelations of these two processes. There are other ways of expressing this idea, such as reference to the blast furnace and the open hearth as an integrated process or by emphasizing the interrelation and interaction of the two processes. Much progress has been made in metallurgy and other fields by breaking complicated processes and reactions into simpler parts and studying each of these intensively. This intensive study frequently is done under the controlled conditions of the laboratory experiment. The entire process is understood better by this specialized study of each of its parts. This procedure is so satisfactory that an understanding of unit operations is a fundamental requirement of chemical engineering. Much discussion of the open-hearth process is in terms of one heat or one furnace. By this is meant that the conclusions apply to one furnace, wherever it may be. Furnaces seldom occur singly; they are located in groups and these groups are located in steel plants having characteristic blast-furnace equipment. Problems that are affected by the number of furnaces operating, by the number of blast furnaces in the plant and by the fact that the open- hearth shop is dependent on the bla furnace capacity rather than on its o needs for the amount of iron available among those which, in contrast to "u operations," we have chosen to call "to operations." Many of these problems, such as cha ing delays and the general mechani problem of material handling, are familiar that merely to define " total op ations" brings them to mind. These pr lems are of such importance that alrea they have received careful thought 2 study and probably will merit furt study. As will be shown later, these mechan problems are so intimately related metallurgical problems of total operati that the effect of certain changes cannot ascribed with certainty to either a mech ical or a metallurgical cause entirely. Although the problems coming under general term of "railroading" are inclu in the problems of total operations, &apos; others are selected for the discussion of paper, One of these is strictly a problem composition; the other is strictly a prob of tonnage production. The problem of phosphorus is pres whenever basic open-hearth slag is used the blast-furnace burden. This practice not secured universal acceptance chi because of difference in preference for h manganese or low-manganese pig iron hjgh-manganese (2.00 per cent) iron is to made, open-hearth slag as a source manganese is usually cheaper than m

Jan 1, 1943

By Albert E. Wood, Edgar R. Shepard

The interest of the Federal Government in improvement of waterways dates from 1820, when Congress appropriated $5000 for making a survey of the Mississippi and Ohio Rivers and assigned this work to the Corps of Engineers of the Army. Since that time the Government has gradually assumed increasing jurisdiction in the matter of improvement and control of inland waterways until, by the River and Harbor Act of Jan. 21, 1927, Congress assigned to the Secretary of War and to the Chief of Engineers the duly of making surveys, in accordance with House Document No. 308, 69th Congress, to formulate plans for the most effective improvement of the navigable streams of the United States and their tributaries, for navigation, development of water power, control of floods, and the needs of irrigation. Virtually all the preliminary investigations and surveys required by this act have been completed. The reports made to Congress have been published and often are referred to as &apos;&apos;308 Reports." The map shown in Fig. 1 is merely a skeleton distribution of the projects covered by these reports, but it serves to indicate the magnitude of the proposed undertaking. In many instances, a single character on the map stands for a major development involving several dams and reservoirs or many miles of canals or levees. The devastating floods of 1936, and the need for worthy public works to take up the slack in employment, gave further impetus to this program and in 1936 led to the enactment of a bill authorizing a large number of these projects. The National Flood Control Act of 1936 specifically authorizes some 270 flood-control projects in 31 states, and affecting nearly every state in the Union, with an estimated construction cost of about $300,000,000. In addition, the 1936 Act directs the Secretary of War to make preliminary examinations and surveys for flood control in some 230 additional localities, and to continue surveys and studies of 18 reservoir sites. The Corps of Engineers is proceeding rapidly with foundation investiga-

Jan 1, 1940

By Paul A. Farrar, Sanford Adler

The Tz-Zr system was reinvestigated using both metallographic and X-ray diffraction techniques. It mas found that titanium and zirconium are soluble in all proportions in both the a and 0 phases. The minimum in the transformation was found at 50 at. pct and 535°C. THE Ti-Zr system has previously been the subject of several investigations.1-6 A study by Hayes et al.5 using magnesium-reduced titanium and zirconium melted in graphite crucibles indicated that the system was a continuous series of solid solutions in both a and 0 phases with a minimum at approximately 545°C and 65 pct* Zr. These conclusions were substantiated by the work of Duwez4 as well as by the limited data of Craighead et al.,3 Fast,2 and deBoer.1 However, a more recent investigation of the titanium-rich region by Ence and Margolin6 indicated that the solubility of zirconium in a, titanium at 500°C is approximately 22 pct with the a + 0 field extending to approximately 47 pct Zr. Therefore in order to resolve this discrepancy the following investigation was initiated. EXPERIMENTAL PROCEDURES The alloys used in this investigation were prepared as 20- to 30-g buttons by nonconsumable electrode melting in a helium atmosphere. The starting materials were Bureau of Mines titanium BHN 71 and Foot Mineral iodide crystal bar zirconium. The titanium was premelted before the alloys were prepared to avoid excessive weight losses in the final melting. The compositions of the alloys prepared were as follows: Ti-12.0, 22.2, 29.0, 39.6, 50.0, 58.0, 72.4, 83.5. and 90.8 pct Zr. Prior to heat treatment the alloys were cold-worked 10 to 20 pct, stopping at the first signs of cracking. Specimens for heat treatment were wrapped in molybdenum sheet and annealed in argon-filled quartz capsules for the following times and temperatures: 750°C-40 days, 675°C-61 days, 600°C—109 days, 575°C-112 days, 550°C-112 days, 525°C—127 days, and 450°C —153 days. Quenching was accomplished by breaking the capsules in an iced-brine solution. The standard techniques used for polishing the specimens involved belt grinding, grinding on emery paper, polishing electrolytically, and etching with Remington "A" etch7 or "R" etch 8 Debye-Scherrer X-ray powder photograms were obtained for a number of samples using a 114.6-mm camera and CuK, radiation. Exposure times were from 19 to 23 hr. The powder samples were obtained by filing to 270 mesh size. After filing the samples were wrapped in molybdenum foil capsuled in quartz and reannealed at the temperature of original heat treatments; following the heat treatment the samples were quenched into iced brine without breaking the capsules. RESULTS AND CONCLUSIONS On the basis of the microstructural examinations of the heat-treated samples and of the X-ray diffraction data, the Ti-Zr system shown in Fig. 1 was constructed. The data indicate that a, and 0 titanium form a complete series of solid solutions with a, and ß zirconium. The minimum was found to occur at 65 pct (50 at. pct) Zr and 535°C, in excellent agreement with the earlier investigations,1-5 see Fig. 2. Typical microstructures are shown in Figs. 3 to 7. Figs. 3, 4, and 5 show the 22.2, 39.6, and 50.0 pct Zr alloys after heat treatment at 675°C for 61 days with the 22.2 pct Zr showing equiaxed a, and the 39.6 pct Zr alloy a + transformed ß, while the 50 pct Zr alloy shows only transformed B. Figs. 6 and 7 show the 29.0 and 39.6 pct Zr alloys after heat treatment for 109 days at 600°C. The 29 pct Zr alloy has an equiaxed a structure while the 39.6 pct alloy has a partially recrystallized a+ß structure. X-ray diffraction data obtained from the 50 pct Zr alloys after heat treatment at 525° and 450°C as well as from the as-cold-rolled material showed only those lineos which couid be indexed a: a titanium, good agreement with the previously published values. 2,4,5,9 Chemical analysis* of the 50 pct Zr alloy

Jan 1, 1967

By David Cole

AT the time flotation appeared upon the metallurgical horizon in Arizona, the writer, under the direction of Dr. Ricketts, was engaged in remodeling and enlarging the No. 6 Concentration Plant of the Arizona Copper Co. at Morenci, and the work had been in progress nearly a year before the Inspiration experiments with flotation had disclosed the revolution in concentration that was at that timè impending. The simplified flowsheet worked out for the remodeling of the Morenci plant had been based upon the removal of the freed metal in a minimum number of stages by treatment upon tables equipped with Butchart riffles, the latter being adapted to accomplish both classification of feed and removal of the metal at one operation, substantially as described in my previous paper.1 The scheme of treatment for the slime was based upon the well-known fact that after copper sulphides, such as chalcocite and chalcopyrite, etc., are reduced to a certain extremely fine state of comminution they are definitely beyond the reach of separation upon any of the concentrating devices then known. By using drag-belt classifiers (which served as conveyors as well as separators), the overflow would be of the usual "slimes" class. Experiment had shown that when these drag-belt overflows were, properly diluted (that is, to about 5 to 7 per cent. solids in the feed under treatment) . the very fine sand, and especially the very fine but still granular sulphide particle&apos;s, would, if given a short distance to fall, quickly settle out in prime condition to yield an excellent recovery on vanners; a further valuable feature would be that the very fine non-separable final overflow tonnage might be discharged direct to tailing, thus conserving space requirements so as to permit within the old building, without embarrass-ment, the increase of capacity required.

Jan 9, 1916

Uranium was the prima donna of 1978, and the exploration pace was fast and furious in traditional uranium producing areas such as the Powder River Basin, Grants mineral belt, San Juan Basin, and Uravan mineral belt. Adding fuel to the fire were several significant discoveries: The Date Creek Basin of western Arizona, the McDermitt caldera of northern Nevada, and Tallahassee Creek in Colorado&apos;s intermontane basin. Advances in solution mining haw resulted in deeper drilling on the Texas Coastal Plain, and the price of uranium has encouraged widespread exploration in frontier areas and non-sandstone environments.

Jan 5, 1979

By Bauer. Larry G.

The vast coal reserves in the Wyoming, Montana, North and South Dakota region are sufficient to supply the total energy needs of the United States for several hundred years. Not only is there an abundance of this sub-bituminous and lignite coal available, but it is easily obtainable by strip-mining . The overburden varies from several feet to several hundred feet. This western coal has yet another asset, namely, a low sulfur content. Whereas eastern and midwestern coal has a sulfur content of 2.5%, the upper Great Plains coal contains sulfur in the 0.5% range. The importance of the sulfur content of the coal is a direct result of federal government emission standards for sulfur dioxide (SO2). Hand (1) points out that "sub-bituminous coals and lignites have a propensity for retaining this sulfur in the ash under certain conditions which is not evident in higher rank coals." This would tend to reduce further the SO2 concentration in the combustion gases of boilers. Western coal is no panacea, however, in that it is far removed from most population and industrial centers. Furthermore, the moisture content of the coal varies from 20 to 40%. This moisture is almost exclusively inherent, that is, it is chemically and physically bound to the organic matter of the coal. It is believed that the water forms a part of the coal structure perhaps as water of hydration of organic salts or organic acids, perhaps by hydrogen bonding, or perhaps by simple adsorption (2). The primary market for this coal is the electric power industry. Lesser markets will be as coke for the steel industry and possible as a raw material for coal gasification and coal liquefaction plants.

Jan 1, 1983

By R. A. Wood, R. I. Jaffee, H. R. Ogden, D. N. Williams

CERTAIN titanium alloys when quenched to retain the 0 phase at room temperature show extensive transformation of 0 to martensitic a during deformation. Alloys of this type are usually characterized by low tensile yield strength, a large spread between yield strength and ultimate strength, and high uniform elongation. A previous investigation of this phenomenon concluded that the principal contribution of the martensitic transformation was to increase the amount of deformation prior to fail-

Jan 1, 1964

C. H. WILSON,* New York, N. Y. (written discussion?).-On page 2680, under the heading Junction Box and Zone Box, the authors say, with reference to the zone-box principle of connections between primary couple, compensator couple, and copper leads, which method in its appli-cation to a single couple is shown in Fig. 34, that if this principle is adopted for a multiple installation, so as to save compensating leads; a selective switch may be (and the inference is that it must be) inserted between the zone box and the different couples, putting the switch at an inconvenient point, or putting up with some complicated interlacing of connections.. Wilson-Maeulen Co. has employed the zone-box method extensively for several years and in none of the many multiple installa-tions has either of those alternatives been resorted to. Instead there has been used a method of wiring with the switch at the indicator and involv-ing no more complications than the junction-box method shown III

Jan 11, 1919

By J. K. Stanley

Iron-cobalt alloys in the range of 35-50 pct cobalt are of interest in the electrical industry because they possess the highest magnetic saturation of any magnetic material known. l1,2The magnetic saturation induction of the 35 pct alloy is 24,200 gausses, compared to 21,600 for pure iron (Fig I). This difference is significant in electrical apparatus, whcre weight or space is at a premium. Saturation values higher than that for iron can be attained up to about 70 pct CO hut economics restrict the use to as low a cobalt content as possible without sacrifice of saturation. Fig 2 shows the iron-cobalt equilibrium diagram. Up to the present time, two factors have retarded the use of iron-cobalt alloys in the electrical industry for magnetic purposes.? One is the high cost of cobalt ($I.50 per pound) and the other ig the inherent brittleness of the binary iron-cobalt alloys. Straight iron-cobalt alloys up to 25 pct cobalt are ductile and easy to process to thin sheet or strip by conventional methods of hot and cold rolling, but the alloys containing higher percentages of cobalt, including those for which the saturation magnetization is a maximum (35 to 40 pct), are increasingly brittle with increasing cobalt, at least up to 50 pct, and are consequently difficult to process, either hot or cold. Work by White and Rah13 indicated that iron-cobalt alloys could be made ductile by alloying with vanadium, and after quenching the alloys (vanadium up to about 4 pct) were found to he colt1 rollable to very thin gauges. With this as a background, we resumed our work on these alloys with the objective of developing methods for economical commercial production of wide strip. For this purpose we have concentrated on the 35 pct alloy in order to obtain the highest possible saturation value. Experiments were carried out on many alloy additions to the iron-cobalt alloys and on the response of these compositions to heat treatments. This work finally culminated in a commercially producible iron-cobalt alloy which has been named Hiperco.* Materials StudIEd and Procedur&apos; Binary alloys of iron and cobalt in the range of 35 pct cobalt are difficult to hot work (by forging or rolling) without such additions as C, Mn, Si, V, Cr, Mo, W Or perhaps others. Another beneficial effect of such additions is that they increase to a greater or less extent the strangely low electrical resistivity of these alloys about 10 microohms per cm3

Jan 1, 1948

ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Member, technical graduate, aged 40, member Institute of Mining and Metallurgy 16 years, with varied experience. Actual underground work,. foreman, surveying, milling, mine examination, superintendent, manager, and other positions of trust. Several years&apos; European practice. Familiar with flotation process. Desires responsible position. References furnished. No. 172. Member, aged 40, graduate Massachusetts Institute of Technology. Twenty years&apos; successful experience as blast-furnace superintendent (merchant and steel works), covering operating, remodeling and? building. General superintendent and general manager of proposition comprising blast furnaces, coal and coke, and iron-ore operation, etc. Good organizer and handler of men. Desires position in above line anywhere. No. 173. Member, technical graduate, aged 43, with 20 years&apos; experience in management of gold, silver, and copper properties and also coal and smelting properties in United States, Canada and Mexico. Owing to illness compelled to resign. Now open for engagement. No. 174. Member, technical graduate, with many years&apos; experience with large smelting and refining companies as chemist, metallurgist, and superintendent desires position. No. 175.

Jan 1, 1915

DAVID WHITE,* Washington, D. C.-This paper is very timely since the Philippine Islands are presumably open to the enterprise of the American driller, whereas much of the territory in that part of the world is closed to us. The United States has ambitious plans for the operation of a great merchant marine, which is to be oil burning in the main, and it takes but a glance at the world map to see the strategic advantage of oil supplies in the Philippines for such marine operations. It is a little difficult to understand why more attention has not been given to the Philippines, in spite of the difficulties attending development in these islands. A number of American oil companies are, I believe, at the present moment taking an interest in the possibilities of the Philippines. Important factors in the formulation of opinion regarding the importance of the oil deposits of the Philippines, as brought out by Mr. Pratt,1 are the point of view and the breadth of experience of the examining geologist. The average oil geologist, whose experience has been mainly in the Appalachian region, the Mid-continent, or Louisiana, or possibly even in California, on seeing the narrowness of the basins, the closeness of the folding, and the presence of igneous rocks here and there, would be likely to draw unfavorable conclusions as to the possibilities of the Philippine Islands. Geologists visiting that region should be familiar with the geological conditions of oil occurrence in Japan, Formosa, the East Indies, or in the Baku district, and their conclusions should be formulated with the knowledge and understanding of the occurrence of oil in those regions rather than in the United States.

Jan 8, 1920

By George Asmus

Closed front, or open front for blast-furnaces, has been for a number of years a much discussed question among the furnace-men in every country where iron is made. As blast-furnaces are costly structures, and as the whole question is one of economy, I hope to be excused for entering a little into details. The "fore-hearth" is a prolonged opening in the lowest part of the hearth, from two to three feet wide, four to six feet long, and two to three feet high. It is a more or less fire-proof box, cooler than

By J. R. Hornaday, A. E. Morris, N. A. Parlee, D. C. Carmichael

Rates of absorption and effusion of hydrogen in solid iron were measurede by a Sieverts type of apparatus. With clean a iron these rates are diffusion controlled down to 420°C and are represented by the equation D = 6.70 x e-&apos;100&apos; crn2 sec-I Certain surface impurities can affect these rates at all temper-atuves. Thin oxide films lower, the apparent diffusivity of annealed iron markedly. Cold-worked iron (75 pct) annealed at 430°C has practically the same solubility and diffusivity as anealed iron. THE mechanism of absorption and evolution of hydrogen in solid iron alloys is not fully understood despite the large number of investigations on the subject. While there appear to be many instances of simple solid-state diffusion control of rate, there are many cases where investigators have either concluded that surface reactions are rate controlling or that some "nondiffusible" hydrogen resides in discontinuities. The purposes of this research were 1) to develop a sound method for studying this absorption and evolution behavior, 2) to examine it in pure annealed iron, and 3) to determine the effects of important variables, such as cold work, surface condition, and composition. This paper relates the progress toward these objectives. Much of the present knowledge of the movement of hydrogen through iron alloys comes from permeability studies which involve the measurement of the rate of passage (under steady state conditions) through membranes of the order of 1 mm in thickness. This method is open to question on various grounds. If surface reactions are involved, two different surfaces operating under two different conditions must be considered. The presence of defects in the membrane even of microscopic dimensions may lead to erroneous results. A few people have studied evolution of hydrogen into vacuum, under carefully controlled (unsteady state) conditions, and some of the best diffusivity data come from these sources. Most of these methods measure rates of evolution only and thus do not make a rigorous test for reversibility of behavior. It appeared that an "unsteady state" method that would permit the measurement of both rates of evolution and absorption under controlled temperature, pressure, and other conditions would offer several advantages. Accordingly the modified Sieverts apparatus described below was designed and built. APPARATUS This apparatus is shown in Fig. 1. The sample bulb is detailed in Fig. 2. Hydrogen of 99.5 pct purity and argon of 99.99 pct purity were used. The hydrogen was deoxidized and dried by means of a Deoxo unit followed by a "Dri-erite" tower. The argon was only dried. The gas burette was graduated in tenths of a cubic centimeter, and, with the aid of a travelling magnifier, readings could be estimated to the nearest 0.01 cc. The level of mercury in the burette was adjusted by means of a leveling bulb operated by a fine screw adjustment. An electrical system, consisting of two slightly separated platinum electrodes inserted in one leg of the manometer and a small light bulb was used to obtain rapid accurate adjustment of the pressure. The capillary tubing of the Vycor sample bulb was 3 mm bore as was all tubing back to the gas burette. The samples were discs made from vacuum-melted Ferrovac-E iron of greater than

Jan 1, 1961

By I. J. Lin

Surfactants are classified according to the size and strength of the hydrophilic and lipophilic groups of the molecule. The balance of these two opposing groups is known as the hydrophile-lipophile balance or HLB. According to this definition, a lipophilic surface-active agent is assigned a low HLB number and a hydrophilic one-a high one. The HLB value is obtained as follows, on the basis of known group values defined empirically by Davies&apos; and listed in [Table 1:]

Jan 1, 1972