Search Documents

By A. B. Kinzel

MUCH work has been done recently in an attempt to analyze the physicochemical mechanism involved in the production of steel by the open-hearth process. . This has resulted in reducing the process to a series of interrelated phenomena obeying the usual laws of mass action and diffusion. Of these, the reaction of the iron oxide and carbon in the molten steel is of most interest from a technical point of view as it con-stitutes the main action in the usual steelmaking processes. A. L. Feild1 has formulated a basic differential equation expressing the open-hearth reactions and Hefty has done considerable experimental work on the determination of a number of constants involved in the basic open-hearth reaction. In considering the application of the law of mass action. to the reaction FeO +C ?? CO +Fe, the iron will be taken as constant, as is the case in the open hearth and the carbon monoxide pressure will be assumed' constant at one atmosphere. From this xy = m at equilibrium, where x is the percentage weight of carbon, y percentage weight of iron oxide and m the weight-concentration equilibrium constant. While it is customary for physical chemists to express equilibrium constants in terms of molar concentrations, the constant is here expressed as the product of the percentage-weight concentrations for ease of comparison with the constants quoted by Herty and by Feild, and for more ready applicability to the open-hearth reactions. Herty and his associates have attempted to calculate the value of this constant from data on open-hearth heats. So many variables affect these results that an adequate calculation presents very great difficulties. A value of 4 X 10-2 was first arrived at, but this was later changed to 1.6 X 10-2. Feild, in order to illustrate the operation of the differential equation of the open hearth, has assumed a value considerably lower than Herty's, namely, 1.0 X 10-2, the largest value consistent with certain theoretical

Jan 1, 1929

By Thomas A. Earl

Much of the strip mining in the Appalachian coalfields was done prior to backfilling and regrading requirements, resulting in many devastated areas which also have serious acid mine drainage problems. Economic incentive or justification for reclaiming these thousands of acres of land does not exist unless some value can be attached to the open cuts and weathered overburden piles. In Pennsylvania many of these old strip mine cuts are being successfully used for sanitary landfills and sludge disposal sites, and multiple benefits are realized. Given proper regulatory control, this technique could be beneficially applied to many other areas in the east.

Jan 1, 1977

By Catherine T. Aimone

Specimens of copper-bearing quartz monzonite were subjected to a plane shock wave simulating high compressional stresses in the proximity of a borehole wall. Fragmentation was studied as a function of stress levels between 1.6 GPa (23 x 104 psi) and 7.3 GPa(105.8x104 psi) and pulse durations ranging from 1.1 µs to 6.9 us. Both explosive pressure and pulse duration were shown to have a strong effect on particle size distribution. While the effect of pressure is well recognized, the effect of pulse duration indicates that ultimate fragmentation increases with the time of application of a plane wave pulse. At high pulse durations, degree of fragmentation is more sensitive to changes in pressure than at low pulse durations.

Jan 1, 1984

A. 0. ASHMAN, Palmerton, Pa. (written discussion?).-Owing to the conflict of the terms thermometry and pyrometry, in numerous cases the entire field of temperature measurements has been divided under these two headings. This confusion is probably clue to the fact that originally a pyrometer was understood to be an instrument for measuring temperatures above the range of a mercury thermometer. In modern practice, however, pyrometers are not only used to measure the temperature over the range of the thermometer, but also to a much

Jan 12, 1919

Industrial Preparedness To Cooperate with the U S War Department General Committee ARTHUR S DWIGHT, Chairman H FOSTER BAIN C K LEITH J EDWARD SPURR H. S MULLIKEN Alternate GEORGE OTIS SMITH POPE YEATMAN

Jan 1, 1923

By Julian Kennedy Edgar

THINKING that it may prove of interest to the Institute, I have prepared a short account of the blowing in and subsequent working of the "A" furnace of the Edgar Thomson Steel Works. This furnace was built for the purpose of making spiegel, but has been started and is now running on Bessemer iron. The shape and size of the furnace are shown in the accompanying drawing. It will be seen that the section is formed of lines making very small angles with each other. In fact, an arc of a circle can be drawn, from the top to the tuyeres, which will nowhere deviate more than two inches from the lines given. In building, also, great pains were taken to gradually round the angles, so that the most careful observer, standing in the crucible and looking upward, could not tell at what points the slopes changed. It will also be seen that the widest part of the furnace is almost exactly midway between the bottom and the stock line, The flattest slope is maintained for 20 feet above the crucible, and is about 1 s inch to the foot from the perpendicular. The furnace is lined with small brick throughout, and has six tuyeres four inches in diameter, which project seven inches inside of crucible. There are three Siemens-Cowper-Cochrane stoves, each 15 feet in diameter by 50 feet high. Blast is furnished by an upright engine with 32-inch steam cylinder, 84-inch air cylinder, and 48-inch stroke. The steam cylinder has balanced poppet valves, working horizontally. The steam valves are worked by a Porter link-movement in order to obtain a variable cut-off. The exhaust valves are worked by a separate eccentric. It is intended to attach a governor to the cut-off, but at present it is set by hand. The steam cylinder is

Jan 1, 1880

By Gerald Edmunds, M. L. Fuller

The development of "fiber" or preferred orientations, during the plastic deformation of metals, and the relation of such structures to the anisotropic characteristics of worked metals has become a subject of common knowledge among metallurgists. Very little has been published, however, relative to variations existent throughout the cross-sections of rolled strips,1 and the influence that such variations may have. This paper presents such a study on a rolled zinc alloy.2 The significance of small differences in surface structure is shown in relation to bending properties. Experience with zinc and its alloys has shown that the outer radius of the bend, which is subject to tensile deformation, is the common region of failure. In considering relations of structural characteristics to bending properties it will suffice, therefore, to consider the ease and possible extent of tensile deformation resulting from various orientations. It is necessary in this connection to assume that on the average the individual crystals of a polycrystalline material act substantially as if their movements were unobstructed by the surrounding grains. This assumption is not strictly valid, but the error involved is unlikely to affect seriously the qualitative conclusions derived from its use. The mechanism of the plastic deformation of zinc crystals has been described by Mark, Polanyi and Schmid3 and by Mathewson and Phillips14 and is regarded as being accomplished by block movements or * Investigator, Rolling Mill Section, Research Division, New Jersey Zinc Co. f Investigator, X-ray Laboratory, Research Division, New .Jersey Zinc Co. 1 Variations of structure throughout the cross-section of wire have been reported in the literature. 2 This alloy contained, in addition to zinc, 1.0 per cent copper and 0.01 per cent magnesium. Its crystal form is hexagonal close packed, the sarne as that of pure zinc. 3 H. Mark, M. Polanyi and E. Schmid: Vorgange bei der Dehrlung von Zink-kristallen. Zlsch. f. Phys. (1922) 12, 58. 4 C, H. Mathewson and A. J. Phillips: Plastic Deformation of Coarse-grained Zinc. Proc. Inst. Met. Div., A. I. M. E. (1927) 143. C. H. Mathewson: Twinning in Metals. Proc. Inst. Met. Div., A. I. M. E. (1928) 7. The results of a further study of plastic deformation of zinc as related to twin-

Jan 1, 1932

By B. A. Kulp, R. R. Reeber

Lattice parameters for the wurtzite form of' CdS mere measured by powder X-ray diffraction techniques over the temperature range 26° to 1000 K'. A negative thermal -expansion coefficient was determined parallel and perpendicular to the c axis below 13.5°K. Near 808°K, the curves of the a, parameter, the differential thermal expansion, and the resistivitv vs absolute temperature exhibited a reversible discontinuity. j\. direct determination of the lattice parameters of CdS over an extended temperature range is of particular use in interpretation of the effects of high pressure on the band structure of semiconductor materials. For example, Langer' has studied the effects of pressure on the absorption edge of CdS from 77°K to room temperature. In order to properly interpret his results it is necessary to know the change in lattice constants as a function of temperature for the wurtzite, zincblende, and rocksalt2 modifications of this material. Thermal-expansion measurements for CdS, wurtzite phase, have previously been determined over a limited temperature range.s74'5 The zincblende phases, of other compounds with similar bonding, have been investigated by Novikova et a! .'' Previous thermal-expansion measurements for metals with hexagonal symmetry have for the most part used bulk sample techniques for low-temperature result. Most X-ray measurements at low temperature have been on materials with cubic symmetry.'jQ The use of X-ray powder-diffraction techniques offers a convenient and accurate method of measurement over a wide temperature range. The X-ray method, besides measuring unit cell size, also provides information about change in structure type and the nature of some of the stacking defects present. I) EXPERIMENTAL PROCEDURE The thermal expansion was measured by X-ray powder-diffraction techniques. Lattice parameters for the range 300" to 1000°K were determined in a 19-cm Unicam camera. From 26" to 300°K a 34-cm back-reflection camera with the Van Arkel" film arrangement was used. The sample was bonded to a copper cold finger below a helium, hydrogen, nitrogen, oxygen, dry ice, or ice brine bath in a metal cryistat. che inner bath was surrounded by another one for radiation shielding. Nitrogen was used in this outer bath for the very low-temperature runs while dry ice and acetone was used for the 195°K point. CuKa X-rays, filtered with a nickel foil, entered the cryostat through a 0.001-in.-thick aluminum window. During a typical 9-hr exposure the sample was continuously rotated through a 30-deg arc. Heat losses from the sample holder limited the minimum temperature attained to 26°K with helium in the inner dewar. Temperature calibration between 25" and 125°K was determined with an Allen Bradley 300-ohm carbon resistor. The resistor was attached to the back of the copper finger with a thin layer of silicone grease. Liquid He, HZ, N2, and O2 baths were used to calibrate the resistor. Temperature variation is estimated to be *2"K with a slightly higher uncertainty at room temperature and 264°K. The thermal expansion of high-purity germanium from 373" to 900°K was measured as a calibration for the Unicam camera. This value was compared with the known value1' for the thermal expansion. A discontinuity in the thermal-expansion coefficient of the CdS a, parameter was observed. Similar discontinuities in the resistivity and differential thermal analysis at the same absolute temperature indicate that the temperature error is *5°K in the temperature range above 500°K. Temperature errors in the Unicam camera below 500°K are appreciably higher due to large gradients in the resistance furnace. II) SAMPLE PREPARATION The CdS was Eagle Picher ultrapure grade. The crystallite size range of the as-received powder

Jan 1, 1965

By H. J. French

WITHIN the past few years, particularly because of the rapid growth of the airplane industry during the war, considerable attention has been paid to the manufacture of light-wall cold-drawn seamless and welded steel tubing for structural purposes. While the manufacture of such tubing is not, in itself, a difficult matter, some difficulties have. been encountered in producing the same under specifications requiring definite physical properties. It is the purpose of this paper to describe the methods of manufacture and the properties that may be obtained by such methods for tubing coming within about ½ to 2 in. (12.7 to 50.8 mm.) outside diameter and 10 to 22 Birmingham wire gage (0.134 to 0.028 in. wall thickness). Such tubing is largely used as structural material in the aircraft industry, and it is of the utmost importance that the physical and chemical properties should be known, and also that the various factors entering into the manufacture should be under such control as to allow these properties to be varied and held within definite limits. In general, tubing may be divided into four classes: namely, specialty tubing, such as riveted-sheet or plate, lock jointed, etc.; brazed tubing; welded tubing; and seamless tubing. Welded tubing may be divided into hot product, such as lap welded and butt, welded, and cold product, such as acetylene and electric welded. Seamless tubing may be hot rolled or cold drawn.

Jan 9, 1919

By Arthur Taggart

THE following conclusions on the work of the Hardinge mill are based on data furnished to the writer by the Hardinge Conical Mill Co. in the form of the mesh cards hereto appended. Energy units (E. U.) and relative mechanical efficiencies (R. M. E.) are computed by the "volume method" of Stadler.1 Screen apertures used are the average apertures of testing screens of the meshes given. Card 122. June 28, 1912. Vipond Porcupine Mines Co., Ltd., Schumacher, Ont., Canada. Ore from mill bin. Gangue, quartz and basalt. 4.5 ft. by 13 in. ball mill. Capacity, 48 tons per 24 hr. Charge, 4,000 lb. balls. Speed, 33 rev. per minute. Horsepower, 15 to 17. Water, 100 per cent. by weight. (50 per cent. ?) Product deslimed and oversize reground-in pebble mill, see Card 113. Feed to mill through 2-in. mesh.

Jan 7, 1915

Attention! Engineers! Geologists! Here is your Opportunity to be of Professional Service The war has interrupted the supply of many minerals, which were normally imported. In view of present transportation conditions, a serious shortage exists in certain materials and will soon develop in others. Some immediate action is imperative. The first thing is to take a careful inventory of American resources. We must know where the ore deposits are, what has hitherto hindered their utilization, what methods must be used, and what equipment will be needed if an emergency demands their rapid development. Many properties must be re-examined from a new point of view, that of present necessity rather than of normal profit. When the shortage is realized, the preliminary steps for relief should have been completed. It is a necessary and patriotic form of mineral insurance. Will you have a part in it? Do not forget that these are war times, and that what may have been valueless a year ago may be a "life-saver" now; an abandoned copper prospect of 1913 might make a successful pyrite mine in 1917. We are fighting an autocratic enemy who knows his resources to the last pound, and uses them with most efficient organization. We have no Kaiser, so each of us must do his share to put our Government in the same situation. The Government needs your facts.

Jan 8, 1917

By M. Mills, M. W. Clegg

This Paper Presents an approximate analytical solution to the problem of the pressure distributions arising from the production of a compressible liquid in a partially penetrating well. The limits of validity of the approximation are discussed and it is shown that the basic approximation is the same as that used in previous numerical of the problem. The variation in pressure at the production well with time for different penetration ratios is investigated and is shown to agree with previous work. The solutiOns are used to assess the effects of partial penetration at large distances from the well and at the wellbore itself. In the latter case the effects of anisotropy are also studied for constant, but unequal, horizontal and vertical permeabilities. It is 'uggested that measurements of the Pressure drawdown below the producing interval in a well should give some indication of a thickness-vertical permeability product for the formation; this would chmacterize the effectiveness of the formation below the producing interval. INTRODUCTION In many oil and gas reservoirs the producing wells are completed as partially penetrating wells; that is, only a portion of the pay zone is perforated. This may be done for a variety of reasons, but the most common one is to prevent or delay the intrusion of unwanted fluids into the wellbore. This paper studies the effects of partial penetration on the pressure distribution resulting from the production of a compressible liquid at a constant rate. To simplify the mathematical analysis the case of a single well located in an infinite reservoir of constant thickness is considered, and it is assumed that this well is perforated over an interval adjacent to the upper (or lower) impermeable boundary of the formation. A well producing from an arbitrary interval within the bulk of the formation could be treated in a similar way, but this action would merely add to the complexities of the solution and contribute little to the appreciation of the over-all effects of partial penetration. In a recently published paper by Odeh,10 the more general problem of producing from an arbitrary interval within the pay zone was studied for the quasi-steady state flow of a compressible liquid, This is the case in which there is a a potential at the outer boundary and a constant flux across the same boundary. This contrasts with the problem studied here, which is concerned with the nonsteady-state behavior in an infinite reservoir. The exact solution of the partial penetration problem presents great analytical problems because the boundary conditions that solutions of the partial differential equations must satisfy are mixed; i.e., on one of the boundaries the pressure is specified on one portion and the flux on the other. This difficulty occurs at the wellbore, for the flux over the nonproductive section of the well is zero, and the potential over the perforated interval must be constant. In the case of constant rate production from the well, this uniform potential is time dependent and unknown, and the additional condition that where hl is the thickness of the perforated interval, must also b'e satisfied. This problem may be overcome in the case of constant rate production by making the assumption that the flux into the well is uniform over the entire perforated interval, so that on the wellbore the flux is specified over the total formation thickness. This approximation naturally leads to an error in the solution since the potential (pressure) will not

Jan 1, 1970

OF what use is the federation to me and why should I support it?" is a question that has been asked by many members of the constituent societies of the F. A. E. S. during the last year; a question that is asked because the speakers do not realize what the Federated is doing or what is the field of its activities. "What is it doing for the profession and for mankind?" would be a more appropriate question, the answer to which is found in the closing chapter of Prof. Cassius J. Keyser's "Mathematical Philosophy."' The chapter is entitled "Science and Engineering." Professor Keyser writes from the layman's point of view. He is looking at the profession and at engineers from the outside. We have in his thoughts the oppor-tunity that Burns sought when he wrote "Oh wad some power the giftie gie us to see oursels as ithers see us." With the permission of the author and the publisher, we quote the following paragraphs: A layman, viewing a profession from the outside, seeking thus to ascertain its proper relations to the common weal, may bring to the task a certain freedom, which, were he a member of the profession, he might have lost. "Men trained in a profession," said Prof. David Swing, "come by degrees into the profession's channel, and flow only in one direction, and always between the same banks. The master of a learned profession at last becomes its slave. He who follows faithfully any calling wears at last a soul of that call-ing's shape. You remember the death scene of the poor old schoolmaster. He had assembled the boys and girls in the winter mornings and had dismissed them winter evenings after sundown, and had done this for fifty long years. One winter morning he did not appear. Death had struck his old and feeble pulse; but, dying, his mind followed its beautiful but narrow river-bed, and his last words were: It is growing dark-the school is dismissed-let the .girls pass out first."' I shall not be so much concerned with the present status of the science as with its potency and promise. Of individual engineers the ideals may be high or low, worthy or unworthy; but of engineering itself the ideal is great and mighty. It is of that ideal that I intend to speak.

Jan 9, 1922

By Y. C. Liu, G. A. Alers

Using X-ray pole-figure information and the single-crystal elastic constants, the angular variation of an elastic modulus in a polycrystal can be calculated and compared to measured clalues. This procedure has been used in the past to provide supporting ecidence for a particular choice of ideal orientations in the description o the X-ray pole figure. Since it is well-known that the absolute value oj an elastic modlus oj a poly crystal cannot be acczrralely calculated from the single-crystal elastic constants, there exists a serious question about the reliability oj this modulus method in the study of textures. This paper deriz-es sez3eral simple fornzulae for the ntzgular lariatiion of Young's modulus in the plane o a rolled sheet sing the same ssuinptions which lead to the lack oj detinztion of the absolute c'alre OJ the elastic ,nodulus. The vesults show that, although the absolute isallre oj Young's modulus depends strongly on the assumptions made, the shape of the modulus vs angle curve is not very sensitive to the assumptions and thus can be used reliably in texture studies. Exatzples oj' using this criteriotz are illustrated in the text. NeARLY all poly crystalline materials have some preferred orientation in the arrangement of their grains and hence exhibit anisotropy in their properties. This preferred orientation is usually measured and studied by X-rays which yield detailed information on the statistical distribution of grain orientations in the form of pole figures. The usefulness of these pole figures in theories of texture formation and in predictions of properties has come to depend almost entirely on the characterization of the pole figure by one or more ideal orientations. Unfortunately, this characterization is not unique and different authors often present different ideal orientations to characterize a given pole figure. In order to distinguish between these different choices of ideal orientations, it is necessary to go beyond X-rays and consider other physical properties which reflect the texture' simply because any choice of ideal orientations must predict correctly the observed anisotropy in all physical properties. The most common example of this procedure has made use of the angular variation of Young's modulus with respect to the rolling direction in the plane of a rolled sheet.3 4 Here the anisotropy can be measured easily and it can also be calculated from the single-crystal elastic constants and the chosen ideal orientation. Unfortunately the methods used to calculate this anisotropy were chosen for their simplicity rather than for their mathematical rigor so that there exists a serious question as to the validity of conclusions reached by this modulus method. It is well-known5 that the absolute value of the Young's modulus of a polycrystalline aggregate cannot be calculated very accurately because different mathematical averages over the grains yield different results. It is one purpose of this paper to examine the effect of different averaging procedures on the calculated anisotropy of Young's modulus in the rolling plane of rolled sheets in order to see if this property can be used reliably in texture studies. This particular modulus and type of material were chosen because the modulus is easily measured and rolled sheet is technologically important. The results show that, although different averages yield different absolute values for Young's modulus, the shape of the modulus vs angle curve is not very sensitive to the averaging procedure and thus can be used as a criterion to check the various ideal orientations used to characterize the X-ray pole figure. Examples of this checking procedure are given in the final section. Another purpose of this paper is to examine the possibility of using the anisotropy of Young's modulus as an indicator of texture without reference to pole figures or ideal orientations. Such a use would require that different textures yield quite different shapes for the modulus vs angle curve so that the distinction between textures would be quite clear. The experimental results presented in the final section indicate that there is easily enough variation in shapes to allow modulus measurements to be useful texture indicators, par-

Jan 1, 1967

By R. W. Smith, R. J. Charles

Fractions of glass particles in the size range 0.5 to 5.0 µ were prepared by an elutriator that operates in a centrifugal field. Although mean sizes of commercially graded abrasive powders were ten times greater than those of samples prepared by the elutriator, frequency size plots for elutriator samples compared favorably. Efficiency of separation was low and amounts of material recovered by the elutriator were small, but the method should find use in preparation of small amounts of sized materials for laboratory investigations.

Aug 1, 1956

By Richard D. Divine

In the Parkes process of extracting precious metals from lead, zinc is added to the molten lead containing gold, silver, copper, and some antimony. These metals, with the exception of antimony, form an alloy with the zinc by reason of their greater affinity for it than for the lead, and this alloy, being lighter than lead, rises to the top, carrying the precious metals with it, whence it can be removed by skimming. These skimmings are further treated for the separation of the zinc therefrom, and the recovery of the precious metals, the zinc being driven off by heat and again used for another operation. In addition to the zinc that combines with the silver, etc., a certain amount is necessary to saturate the lead, and it is therefore necessary to treat the desilverized lead to free it from this residual zinc. TO do this it is heated again in a reverberatory furnace and air or steam is blown through it. This oxidizes the zinc together with a small amount of lead and antimony, leaving the lead free from zinc and antimony, and forming oxides of these metals, which rise to the top and are skimmed off. This process relates to the separation of the metals in these oxides or skimmings. The skimmings are cooled, crushed, and mixed with carbonate of soda and pulverized oil coke. The mixture is heated in a reverberatory furnace on a bath of lead, to about 1,000" C. The metals are reduced by the coke, the lead and antimony go into the lead bath, while the zinc is volatilized and burned to oxide. This impure oxide is at the present time treated at Omaha by the Hall process of electrical precipitation, making a very pure metallic zinc. It can also be very easily refined by the old Schnabel process of using ammonia and carbon dioxide as a solvent. It seems to be in an ideal form for this purpose, and very few changes from the original method are required to obtain the zinc oxide practically C. P., leaving the lead and antimony as residues. There has been considerable difference of opinion regarding the effect

Jan 1, 1915

Jan 1, 1885

By Lawrence Adler

In-situ rock has well-recognized rupture and yielding responses. Attention is called to an intermediate response, granulation, which consists of an evenly distributed, small-scale crumbling accompanied by swelling. Granulation results in a negative slope for the inelastic portion of the stress-strain curve as successive interlocks are destroyed, and the load-carrying capacity of the material is reduced. Volumetric swelling with softening also takes place. The prerequisites for such a response are moderate confinement and a uniformly distributed defect pattern. Since rock masses, as well as rock as an intact material, have such patterns in their jointing and texture, respectively, granulation is characteristic of them. The presence of granulation can be demonstrated for a very wide scale, ranging from laboratory testing to regional geologic phenomena. The response of an engineered structure is considered in detail. Granulation appears to be dependent upon internal moments, the formation of which can be controlled by engineering design. The practical implications of such control can be significant in optimizing underground instability and in improving excavation techniques. Rock is usually considered to behave inelastically under high load, by fracturing as a brittle material, or by yielding as a ductile material, ignoring time dependency. These responses, which are characteristic of metallic behavior, appear idealized in Fig. 1, where linear-elasticity approximates the initial behavior. However, another major deformation mechanism peculiar to rock has long been recognized in geology, the granulation of an interlocked material. Granulation consists of a uniformly distributed fracturing and crumbling of the material, accompanied by swelling and softening. Predictably, the associated inelastic portion of the load-deformation curve has a negative slope,

Jan 1, 1971

Discussion of the paper of F. E. Lucas, presented at the Cleveland meeting, October, 1912, and printed in Bulletin No. 71, November, 1912, pp. 1315 to 1326. F. Louis GRAMMER, Leesburg, Va. (communication to the Secretary *):--Mr. Lucas's paper reminds us of our extravagance in coking, and our tardiness in the adoption of by-product ovens, as compared to Germany. We are, however, so rich in coal-having mined, so far, less than 1 per cent. of our known national resources-that the argument of conservation is not very pressing. It is true that our so-called coking-coal beds are not inexhaustible; but by-product ovens coke coal that bee-hive ovens cannot handle, and so really enlarge our reserves of coking coal. " Conservation of Resources " is a phrase in great vogue. It is overworked and abused at times; being used by those who desire to be the exclusive custodians of resources or the sole purveyors of commodities. It does not carry great weight as regards coal. There are, however, aside from the attractive considerations of profit set forth by Mr. Lucas, several other important reasons why by-product ovens should be introduced more widely. One is that coal-tar pitch is the keynote to the extension of the coal-briquette industry. The more coal-tar pitch is available, the more briquetting will be carried on; and this will utilize much coal which is either waste or a drug in the market. Heretofore, in several instances coking and steel-making plants have been built, primarily, to market bituminous slack.

Jan 5, 1913

By Andrew Mayer

EARLY in 1942 National Lead Co. was requested by the War Production Board to construct and operate a plant for the Government to produce magnesium by the ferrosilicon process which had been developed by Dr. L. M. Pidgeon in the laboratories of the Canadian National Research Council. A contract with the Defense Plant Corporation was concluded in May 1942 and Magnesium Reduction Co., a wholly owned subsidiary of National Lead Co., was formed to carry out this project. The capacity of the plant was rated at 10,000,000 lb. of magnesium per year, equivalent to an average production of about 14 tons per day. THE PROCESS The process, in brief, is as follows: The raw materials are dolomite and ferrosilicon, 75 per cent grade. The dolomite is calcined, the calcine and ferrosilicon are ground and mixed and the mixture is briquetted. The briquets are charged into tubular retorts of chrome-nickel steel set horizontally in a furnace with the open ends projecting outside the front wall. The retorts are then closed and evacuated. Magnesium is liberated according to the reaction 2(MgO, CaO) + Si = 2Mg + 2CaO, SiO2 It is distilled from the charge and condensed on a removable sleeve in the throat of the retort. Sodium and potassium, if present, are also liberated, distilled and condensed on a "sodium condenser" in the end of the retort. At the expiration of the distillation period the retorts are discharged and the cycle of operations is repeated. For the rated daily capacity of ±. tons of magnesium there are required approximately 170 tons of dolomite, equivalent to about 85 tons of calcine, and 16.5 tons of ferrosilicon. The retort residue, a bulky powder which at present is waste, amounts to about 87 tons. CHOOSING THE SITE The investigation to select the location of the plant was conducted by the Research Laboratories of National Lead Co. This work included geologic and economic surveys of a number of districts, examination of dolomite samples by chemical, spectrographic and petrographic methods and large-scale tests of dolomite from several of the more promising localities. In the last-named tests 2-ton samples were put through the ferrosilicon process in the pilot plant of the Canadian National Research Council, under the guidance of Dr. Pidgeon. The conclusions drawn from the investigation, in regard to the quality of dolomite to be used in the ferrosilicon process, were: First, the dolomite should contain not less than 21 per cent MgO

Jan 1, 1944