Search Documents

By Frederick F. Frick

SPONGE iron as produced at Anaconda is a fine, -35 mesh, impure product, about 50 pct metallic iron, obtained from the reduction of iron calcine at a temperature of 1850°F by use of coke resulting from slack coal. The metallic iron particles are bulky and spongey and precipitate copper readily and rapidly from a copper sulphate solution. Investigation of the treatment of Greater Butte Project, Kelley, ore at Anaconda early showed the desirability of using sponge iron as a precipitant for the copper in solution resulting from desliming of the ore in a dilute sulphuric acid solution.

Jan 1, 1953

By M. C. Fuerstenau, D. W. Fuerstenau

Studies of the collection of alkali and ammonium halides utilizing vacuum flotation techniques and contact angle measurements show that ionic size controls the flotation of techniquesthese halides with amine salts measurementsas collector. Contact angles of air bubbles on sylvite in saturated brines were withaminemeasured salts asascollector.a function of such variables as collector addition, length of collector chain, and pH of the brine. No contact occurs between halite and an air bubble in brines containing dodecylammonium acetate as collector. LONG-CHAINED aliphatic amine salts have been used for the separation of sylvite (KCl) from halite (NaCl) by flotation.1,2 It is puzzling how these two minerals, which are so similar chemically and crystallographically, can be separated by this method. Gaudin" has postulated that the difference in floatability of halite and sylvite with salts of primary amines depends on ionic size: In the case of amine flotation, the cation would attach itself to the chloride. I have a speculation there, which I cannot prove, that the ammonium group, that is the —NH3 group in the amine, floats potassium chloride because the dimensions of this grour, as it has been measured in other compounds is almost identically the dimensions of the potassium ion, quite different from the sodium ion, and so it fits where potassium had been, in place of it and not attached to it. Apparently, because an aminium ion (RNH3+) is much larger than a sodium ion, it cannot fit into the lattice of halite. Taggart also has speculated that ionic size may control the floatability of sylvite.4 The object of this experimental investigation has been to test this hypothesis and to study what controls the adsorption of cationic collectors at the surface of sylvite. Since collection is to be approached from the viewpoint of ionic size, the ionic radii that are of interest in this work are presented in Table I. The values of the ionic radii of the ions listed in Table I, except NH4+, are those given by Pauling." Several different values for the radius of the ammonium ion have been given, but that of Goldschmidt6 seems to be preferred. The radius of the charged head of a dodecylammonium ion is assumed to be the same as that for the ammonium ion. Little experimental work has been reported in the technical literature concerning the separation of sylvite from halite by flotation. Guyer and Perren studied the separation by flotation of 50 pct binary mixtures of NaCl, KC1, NH,Cl, NaNO3, KNO3, K2SO4, and Na,SO, using either oleic acid or a sodium sul-fonate as collector.' It is possible to measure floatability under actual flotation conditions where all three phases, air- water-mineral, are present by vacuum flotation tests and contact angle measurements.9 Both of these techniques were used in the experimental approach in this paper. Experimental Method and Materials The vacuum flotation tests were run with glass-stoppered pyrex graduated cylinders. Twenty-five ml graduates were used to test the floatability of all salts studied except rubidium and cesium salts. For each test distilled water containing the desired collector concentration was saturated with the salt to be floated. Sufficient salt (—48 mesh) was added to leave about 2 ml of solids in the bottom of the graduate. After the graduate had been agitated several minutes to saturate the solution with air, a vacuum was applied. If the salt were floatable in the collector solution, the gas bubbles attached themselves to the particles, and the particles floated to the surface. In determining the floatability of the expensive Rb and Cs halides, the experiments were run in 10 ml graduates with about 11/2 ml of collector solution initially. Contact angles were measured in the usual manner except that the solutions had to be previously saturated with the mineral to avoid dissolution of the crystal. Solutions for studying contact angles were made by adding the desired amount of collector to a saturated brine, giving the collector concentration in molarity. The mixture was agitated until dissolution of the collector was complete, with the exception of those concentrations greater than about millimolar. At these high concentrations complete dissolution of the collector was impossible. The face of the mineral to be tested was a freshly cleaved crystal of halite or sylvite. The mineral was placed in the brine and conditioned with collector for at least 15 min, which was found to be long enough to obtain a maximum value for the contact angle. The temperature remained constant during each experiment. The experiments were run at 24°C ±2°C. For contact angle measurements, a crystal of halite from Carlsbad, N. M., was used. Several samples of sylvite were used in this work: a crystal of sylvite from Stassfurt, Germany; a crystal from Carlsbad, N. M.; and a crystal of chemically pure potassium chloride. Saturated brines were made from reagent grade chemicals and distilled water.

Jan 1, 1957

By H. A. Bedworth

ALLOYS of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry1 proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche3 and Corson.4 The constitution of the system has also been recently investigated by Matuyama,5 and in the laboratories of the American Brass Co. by Smith.6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of, the constitution of copper-silicon alloys, the solubility reaches its maximum value, 6.7 per cent. silicon, between 721° and 782° C. At 852° C. the solubility is 5.25 per cent., while at 400° C. it is only 4.1 percent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent. silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

By W. C. Phalen

SALT-MAKING PROCESSES THE production of salt in the United States divides itself at the outset into two distinct classes: (1) The mining of rock salt and its purification and separation into marketable sizes, and (2) the production of salt by evaporation from brines, bitterns, and other solutions. The processes employed at the present time in the manufacture of salt by evaporation may be outlined as follows: 1. Solar evaporation. 2. Direct-heat evaporation (a) in open kettles; (b) in open pans. 3. Steam evaporation, (a) in jacketed kettles, (b) in grainers. 4. Vacuum-pan evaporation. In this paper only the solar-evaporation processes practised in different parts of the United States will be described. SOLAR EVAPORATION Localities In the Eastern States the solar-evaporation process is not generally employed for climatic reasons. In the Western States, particularly in California and Utah, the great bulk of the salt produced originates in the solar-evaporation process. Of the Eastern States producing salt, this process, so far as the writer is aware, is employed in New York State only.

Jan 9, 1914

By H. A. Schwartz

THE spheroidal form of the temper carbon nodules in malleable cast iron and of the graphite mottles of "mottled" cast iron suggests that in both all the graphite in a given mottle or nodule grew from a single center of crystallization or nucleus.? There is, however, a distinct metallo-graphic difference between the mottle and the nodule; the area of mother metal impoverished in combined carbon by the crystallization of graphite in a mottle is practically coextensive with the ramifications of the graphite, while the impoverished zone of metal corresponding to a given nodule is always larger, and usually much larger, than the approximately spherical mass of graphite crystals forming the nodules. Furthermore, the mottle probably is formed during freezing and the nodule almost always at a considerably lower temperature. Assuming that the nodules or mottles can be used as a measure of the existing nuclei, (capable of germination) we propose to record certain observations as to the graphitizing reaction in the light of the number and habits of growth of these nuclei. The present authors, in cooperation with others1-7, have reported upon various cognate aspects of the problem. The fact that temper carbon is a mass of flakes and not a solid granule has become well recog-nized since the introduction of an improved polishing technique8,9,10 for cast iron. The problem of deriving from the circular planar intercepts

Jan 1, 1935

By E. H. Jr. Dix

THE consideration of alloying elements for aluminum has led to a series of investigations of the equilibrium relations between aluminum and those alloying elements. Therefore, the aluminum end of the aluminum-antimony diagram has been studied. The general form of the aluminum-antimony equilibrium diagram has been worked out by Campbell and Mathews1 and by Tammann.2 Campbell and Mathews described principally the beginning of solidification. They found the curve of beginning of solidification to rise gradually from the melting point of pure aluminum to a maximum at about 67 per cent. aluminum. After a slight lowering of the curve at a little greater antimony concentration the curve again rises to a maximum at 18.4 per cent. aluminum, which corresponds to the compound AlSb. The curve then drops to the melting point of pure antimony. Tammann explained the maximum occurring at about 67 per cent. aluminum as the result of the slow formation of the single compound AlSb. The space lattice of the compound AlSb, according to Owen and Preston,3 is face-centered cubic, the antimony atoms being intermeshed with an identical aluminum lattice. Very little, if any, work has been done on aluminum alloys containing small amounts of antimony.

Jan 1, 1930

By N. J. Themelis, P. Spira

The efficiency of the reverberatory furnace operation in producing. slags of 1020 copper content depends on the mixing and flow conditions in the bath. Radioactize-tmcer tests have indicated the jkaction of bath volume engaged inflow and the mixing conditions in the bath. The factors controlling the flow pattern of slag have been classified as laminar transfer flow, natrsral convection, and flou, due to the rapid addition or removal of slag.. Similarity criteria for model studies have been developed. The pyrometallurgical processing of copper begins with the smelting of either flotation concentrates, or direct-smelting ores which have been partially roasted to calcines. These materials are generally smelted in a reverberatory furnace, Fig. 1, and separate into two liquid phases, a sulfide matte and an iron silicate slag. he matte is tapped and subsequently reduced to metallic copper in a converter, while the reverberatory slag is usually discarded without any further treatment. Molten slag from the converting operation is returned intermittently to the reverberatory in order to recover its high copper content (1 to 3 pct Cu). The reverberatory furnace is about 115 ft long by 30 ft wide. In general, the solid charge is fed at intervals through openings along the sides of the roof and forms sloping banks from which the molten materials trickle down into the bath; the charge banks extend over a length of about 70 ft from the firing wall. The depth of the slag and matte layers varies from smelter to smelter; in the Noranda furnaces, the slag depth is 24 to 30 in., while the depth of matte at the taphole is about 20 in. Apart from smelting, the functions of the reverberatory are to recover most of the copper content in the converter slag by physical and chemical interaction with the furnace bath, and to provide adequate time for optimum separation between matte and slag. The efficiency of these operations depends on the mixing and flow conditions in the bath and is reflected on the copper losses in the slag. In the present study, the reverberatory furnace is considered as an open-channel chemical reactor and the driving forces for material transport through the bath are examined by means of flow and mathematical models. FLOW CONDITIONS IN THE REVERBERATORY FURNACE To facilitate the study of mixing conditions in continuous-flow reactors, two idealized patterns of flow have been accepted by workers in this field.' The term "backmix" flow is used to describe complete and instantaneous mixing in the reactor (perfect mixing); all particles have the same chance of leaving the system, independently of their time of entrance, and the fluid is uniform in composition throughout the vessel. On the other hand, "plug" flow, or "piston" flow, assumes that a fluid element moves through the reactor without overtaking or mixing with fluid entering at an earlier or later time. In addition to the two idealized patterns of flow, "deadwater" flow accounts for that portion of the fluid which is moving so slowly that it may be assumed to be stagnant. According to the definition by evensppiel,' the cut-off point between active and stagnant fluid may be taken as material which stays in the vessel for a period twice the mean residence time. The flow patterns in real vessels may be approximated by a combination of the above flows. Thus, the vessel is assumed to consist of interconnected flow regions with various modes of flow existing between them. The flow pattern may be determined directly from the flow paths of fluid through the essel. -However, the difficulty of obtaining and interpreting such information has led to the alternate approach of determining the residence time distribution of fluid elements by means of stimulus-response studies. The stimulus is provided by introducing a tracer in the inlet stream and the response by the record of the change in tracer concentration in the exit stream from the reactor. Such tests have been conducted in glass tank furnaces using either chemical7"9 or radioactive tracers1'-'' and, in one case, experiments have been reported for a metallurgical furnace.'"

Jan 1, 1967

By C. G. Maier

COMMERCIAL processes of lead softening directly involve the behavior on fusion of mixtures of the oxides of antimony and lead, and the vapor pressures of these materials. Practically no quantitative data have been available for the discussion of lead softening from the point of view of the fundamental metallurgy of the process. The Pacific Experiment Station -of the United States Bureau of Mines, in cooperation with the University of California, in the course of its program of study of the fundamental properties of oxides and sulfides, recently made vapor pressure measurements upon the various forms of pure antimony trioxide.1 When these measurements were considered in connection with the softening and "fuming" furnaces which are often used for lead purification, an unexpectedly anomalous condition appeared. In brief, this anomaly consisted in the fact that in certain softening furnaces, where lead bullion of approximately 1 per cent antimony content was being treated at a temperature of approximately 1300° F., no appreciable volatilization of antimony occurred, there being produced only a "skim" containing from 15 to 20 per cent Sb, 65 to 60 per cent Pb, as mixed oxides. In the "fuming furnaces," where the temperature was only about 1400° F. and where an accumulation of "skims" from the primary softener was being treated with certain other antimony-containing materials, a considerable volatilization of antimony as oxide occurred; an "impure" skim of some 60 to 65 per cent Sb and 10 per cent Pb was also produced as mixed oxides. The latter material cannot be suitably treated in hearth-type or softener furnaces. The essential chemical difference between the first and second step is the customary use of some reducing material (such as petroleum coke) in the later operation. An obvious interpretation of the effect of coke in facilitating the fuming of the antimony is the supposition that the antimony may be reduced to metal, and volatilized as such. This supposition is improbable, however, when it is realized that a slight extrapolation of the vapor-

Jan 1, 1932

Jan 1, 1938

By R. E. Crater

Brown, Gaudin, and Loeb in their study of intergranular comminution by heating attempt to find one explanation for all types of rock in terms of the properties of the phases present. The only necessary condition for intergranular cracking by heating is the setting up of high stresses at the grain boundaries. Such stresses may be set up in multiphase isotropic mixtures if the thermal expansions of the phases are different, in non-cubic single phases because of the anisotropy of thermal expansion in the various crystallographic directions, and in materials containing quartz because of the a-ß transformation at 575°C. In addition, for intergranular comminution by heating, the cooling and not the heating is most important.

Jan 3, 1959

By J. P. Neumann, Y. A. Chang

Lattice parameter measurements of the hcp phase in the system Ag-A1 near the stoichiometric composition Ag2Al were carried out for specimens quenched from 825°K, annealed for 10 days at 453°K, and annealed for 100 days at 413°K. The three heat treatments resulted in the same lattice parameters at room temperature. None of the specimens showed any superlattice lines. The lattice parameters of this alloy were also measured at temperature from 77° to 750°K. An anomaly in the temperature variation of the lattice paramete.rs occurs in the region near 400°k, which may be associated with local ordering. FROM measurements of the diffuse scattering of X-rays, it is known that the [ phase in the system Ag-A1 near the stoichiometric composition Ag2A1 ex- hibits a considerable degree of short-range order at room temperature.' Moreover, based on the position of the short-range order peaks a superlattice model had been proposed in the same study and it was suggested that lowering the annealing temperature to 420°K might result in long-range order. In the present study, the diffraction patterns and the lattice parameters of three differently heat-treated specimens, i.e., quenched from 825°K, annealed for 10 days at 453°K, and annealed for 100 days at 413°K, were determined from 77" to 750°K. The purpose of these measurements was to investigate 1) whether long-range order could be established by prolonged annealing and 2) whether the lattice parameters at room temperature depended on the heat treatment, since it had been proposed earlier2 that the lattice parameters in this phase are related to the atomic arrangement. 1) EXPERIMENTAL TECHNIQUES Silver and aluminum, both 99.99 pct purity, were melted in a zirconium oxide crucible under helium in

Jan 1, 1969

By O. N. Carlson, A. L. Eustice

The tensile properties of iodide vanadium were determined as a function of hydrogen concentration. It was shown that the presence of 10 ppm H is sufficient to cause embrittlement of vanadzum over a limited temperature range. The temperature of the observed ductility mininlum is approximately -l00°C, this being a function of strain rate and hydrogen concentration. The yield stress of hydrogenated vanadium is raised sharply in the brittle temperature range. THE present investigation was initiated to determine the effect of hydrogen on the tensile properties of high-purity vanadium as a function of temperature and the role of hydrogen in the brittle-ductile transition. Loomis and Carlson&apos; reported a change from ductile to brittle behavior in iodide vanadium at -110°C with a return of ductility at temperatures below -140°C. Vanadium wire containing 270 pprn of hydrogen was brittle at room temperature while wire containing 100 ppm was ductile under the same conditions. Roberts and Rogers&apos; reported a ductile-brittle-ductile fracture sequence in vanadium containing 400 to 600 ppm of hydrogen. Their data show that hydrogenated vanadium is ductile at 150"C, brittle at room temperature and ductile again at -196°C. Magnusson and Baldwin found a minimum in ductility in vanadium containing 80 ppm hydrogen from tensile tests performed at several strain rates. Information available on the vanadium-hydrogen equilibrium system4 is somewhat incomplete. The absorption of hydrogen is exothermic in accordance with the decline in solubility with rising temperature. The limit of solid solubility at temperatures below 400°C has not been determined due to the difficulties in obtaining equilibrium at these temperatures. Data on the hydrides of vanadium are rather limited. Roberts6 studied the structure of VD,., by neutron diffraction, and observed the ordering of the deuterium atoms below -65°C into a primitive cubic cell with a lattice constant about twice that of the disordered bcc vanadium solid solution. EXPERIMENTAL PROCEDURE Vanadium of 99.9 pct purity was prepared by the iodide refining process6 for use in this investigation. This vanadium contained the following analyzed impurities; <20 pprn calcium, 150 ppm carbon, 200 ppm chromium, 30 ppm copper, 10 ppm hydrogen, 200 ppm iron, <20 ppm magnesium, <20 ppm nickel, <5 ppm nitrogen, 150 ppm oxygen, <50 ppm silicon, and <20 ppm titanium. specimen Preparation—Tensile specimens were machined from swaged rods of iodide vanadium. The

Jan 1, 1962

Jan 1, 1937

By T. Sterry Hunt

It is now five years since I called the attention of the Institute to the industrial importance of the coal and the iron ores of the Hocking Valley in Southeastern Ohio, and in a pamphlet on the region published soon after, in 1874, endeavored to resume the principal facts then known respecting it, including the observations of the geological survey of Ohio, made and published up to the time by Professors Andrews and Wormley, together with an estimate of the probable future of the region, and its relations to the coal and iron markets of the country. Since that time the labors of the Geological Survey have included a further study of the coal by Prof. Edward Orton, the results of which will be awaited with much interest. I may say from my knowledge of them, that while confirming the general conclusions of his predecessors, he has been enabled to add much to our knowledge as regards the correlation of the various members in different parts of the coal-field; and to show more clearly the positions and the importance of the ore-beds in the Hocking Valley region. The only ore mined in that vicinity previous to 1874, was below what is called the Great Vein or No. VI coal, and to the west of what is known as the Hocking Valley coal-field, and although experiments in a few furnaces in the State had shown that this coal could be used with advantage in iron-smelting there was not a single blast furnace within the field. My observations at that time, however, impressed me with the abundance of iron ore, not only below but above this important coal seam, and I then ventured to express the opinion that this region, from its cheap and easily mined smelting-coal, its native ores and limestones, and its geographical position and relations to the great markets of the West, and to the supply of rich iron-ores from Lake Superior, was destined at no distant time to become a great metallurgical centre, where iron could be made more cheaply than at any other equally accessible point in the country. The object of the present communication is to report progress, and to state how far my observations made in the region 1st month have justified the predictions of 1874. The five years which have elapsed have been, as all know, most unfavorable to the iron trade, and especially to new enterprises in untried regions, yet they have not passed without important industrial developments in the Hocking Valley, where not less than thirteen blast furnaces have been erected

Jan 1, 1879

By E. C. Carris

THE loading of bituminous coal mechan¬ically was recognized about the year 1900, but during the following 28 years less than 5 per cent of the bituminous pro¬duction in the United States was loaded by mechanical means. During the past i6 years, however, the usage of some form of mechanical loader has had a very rapid and accelerated growth, until at present production of bituminous coal by mechanical means has reached an all¬time high of approximately 46 per cent, and is still increasing. This rapid growth in the use of the mechanical loader has been supplemented by an increase in mechanical cleaning. The importance of mechanical cleaning of coal was recognized many years before the mechanical loader was introduced, because of the impossibility of cleaning manually the sizes below 2 in., and the increasing competition from other fuels. Utilization of mechanical loaders without mechanical cleaning on the surface for at least one or more sizes is the exception, rather than the rule. One exception is a mine that employs caterpillar-mounted mobile loaders exclusively, and mines the entire seam without any selectivity, and yet loads and ships six grades of coal of the very highest quality without mechanical cleaning. Such a fortunate situation can exist only where mining conditions are ideal, where top and bottom are exceptional and there are no impurity partings, and where there is loader height. The conversion from hand loading to mechanical loading has definitely intro¬duced many problems in the preparation plant of yesterday and in the modern streamline plant as well. Many of these problems have been solved by good, sound, conscientious initiative on the part of the plant personnel, with minor expendi¬tures; the solution taking the pattern of rearranging and improving the equipment at hand. Other problems have caused, and are causing, considerable concern and difficulty. LARGE IMPURITIES The removal of large quantities of large impurities from the lump coal, and their handling and disposal, is definitely a troublesome and costly problem. The cost of manually removing the impurities from the picking table alone, based on the actual recovered lump coal, can reach a cost of 42 cents per ton or more. In the design of future plants it would be wise to give this phase of preparation considerably more time and thought, particularly if the seam of coal contains one or more heavy partings and the mining procedure is all seam. This same caution applies to seams that may not contain heavy partings but have poor and heavy draw-slate top, which falls with the coal during the mining cycle. One of the more recent of the modern preparation plants has answered this problem by installing a rock crusher under the picking table in such a manner that the impurities can be diverted by gravity directly to the crusher. This reduces the

Jan 1, 1946

By S. E. Bretherton

Mr. AllaW Gibb, of Mount Perry, Queensland, Australia, in an interesting and instructive paper,* describes fully the great difficulties metallurgists encounter in seeking to produce marketable copper by smelting refractory ores containing arsenic, antimony and bismuth. After reading this description, I prepared a paper for the Institute, which was, however, through a misunderstanding on my part, published in the San Francisco Mining and S&apos;cie~ztiJic Press of April 4, 1903, after its acceptance by the Council, and without credit to the Institute. Consequently, it cannot be reprinted for the Transactions of the Institute; and I can only here summarize its contents and conclusions, referring the reader to the article above named for further particulars. In that article I omitted the col~sideration of bismuth, which we do not encounter in our smelting at Val Verde, and added lead and zinc, which Mr. Gibb had not discussed; and I undertook to shorn, by the record of a year&apos;s practice of the Val Verde Copper Co., Arizona, that copper-ores containing arsenic, antimony, lead and zinc may be successfully smelted, without preliminary roasting, in an ordinary blast-furnace with hotblast, making a normal slag, such as one would aim to make under ordinary conditions with cold-blast, so as to produce a marketable matte, containing not less than 45 per cent. of copper, free from arsenic and antimony, and below the limit in lead and zinc penalized by the refineries.

Jan 1, 1904

By C. S. Matthews, P. Hazebroek, F. Brons

A method has been developed for calculating the average pressure in a bounded reservoir. The reservoir is first divided into the individual drainage volumes of each well, by using the criterion that at steady state each individual drainage volume is proportional to a well&apos;s production rate. The average pressure in each drainage volume is then calculated by a method developed in the report. By volumetrically averaging these individual drainage volume pressures, the average pressure in the entire reservoir is obtained. To calculate the average pressure in each drainage volume, a correction is applied to the ordinary extrapolated pressure, i.e., the pressure obtained by extrapolating to infinite time the linear portion of the graph of closed-in pressure versus log[?t/(t + ?t)], where At is the closed-in time and t the production time. The correction, which is a function of the production time, is presented in graphical form for different shapes of the drainage area (horizontal cross section of the drainage volume). INTRODUCTION It is important to be able to find the volumetric average pressure in a reservoir so that the size of the reservoir may be determined from material balance calculations. It is also desirable to be able to find the approximate distribution of pressure within a reservoir for detection of fluid movement. &apos;The purpose of this paper is to present a method for calculating both the average reservoir pressure and the approximate distribution of pressure within a bounded reservoir — that is, a reservoir with no water drive. In reservoirs where the pressure builds up rapidly after wells are shut in, the determination of average pressure generally poses little problem, for one often need only average the final buildup pressures. It is when pressure buildup is slow that difficulties arise. For practical and economical reasons, the time allowable for closing in wells is limited. If at the maximum allowable closed-in time the pressure has not reached a con- stant value (and this is more often the case than is generally realized), calculation of average pressure presents difficulties. One method which has been used in the past for obtaining an "average" pressure involves the extrapolation to infinite closed-in time of curves of pressure as a function of closed-in time. Contour maps of these extrapolated pressures are used in arriving at an average pressure. In some cases wells are shut in for arbitrary Lengths of time, and contours of these arbitrary shut-in pressures are used for calculation. All these methods are somewhat arbitrary and suffer from lack of fundamental theoretical basis. For example, no precise meaning can be given either to the extrapolated or to the arbitrary shut-in pressure. Furthermore, there seems to be no reason why either set of pressures should be contourable. It was because of the vagueness of these old methods and their lack of a sound theoretical basis that, the present method for determining average reservoir pressure was developed. SYMBOLS A = drainage area of a well, cm&apos; A, = drainage area of well j, cm2 A , = total drainage area of all wells in a reservoir, cm2 c = coefficient of compressibility of fluid at reservoir temperature, atm-1 f = hydrocarbin-filled porosity, fraction h = net thickness of formation, cm k = permeability of formation, darcy p = pressure at a well, atm p0 = initial reservoir pressure, atm p* = pressure obtained by straight-line extrapolation of linear portion of plot of p versus log [At/(t+ At)] p = volumetric average pressure inside drainage volume of a well q = volume flow rate at a well, cc/sec a: prevailing reservoir conditions q, = total volumetric flow rate from a reservoir, cc/sec at prevailing reservoir conditions rw = radius of well bore, cm T = kt/fµcA t = corrected time of production of a well, seconds, defined by

Jan 1, 1955

By J. T. Pardee

INTRODUCTION PLACER is a Spanish word, the definitions of which include "an extensive bank of sand or gravel" and "a place where currents of water deposit particles of gold."l The term, probably first used in the western hemisphere by Spanish or Mexican gold miners, is now generally applied to all detrital deposits that yield valuable minerals by washing. In the Western States placer products other than gold, including the silver alloyed with it, are chiefly sapphires, produced in Montana, and platinum alloys recovered in California and Oregon. During the war tungsten ore (scheelite) was obtained from placers in the Atolia district, California, and a number of diamonds have been found in the Sierra Nevada gold belt. Small amounts of stream tin have been produced in the Black Hills of South Dakota and a little monazite sand in the Boise Basin. Idaho. Magnetite, chromite, ilmenite, zircon, and other useful minerals are more or less abundant in the beach placers of the Pacific coast and in the heavy residues of placer mining elsewhere, but the problems of profitably separating and marketing them remain to be solved. Minerals of lead, quicksilver and other metals occur in many of the placers and although not plentiful enough as a rule to be worth recover-ng, their presence has, in several instances, led to the discovery of valuable lodes, notably at Leadville, Colorado. Historical summary.-In New Mesico, Arizona, and Southern California, placer gold was mined by Mexicans and Spanish priests in the first half of the 19th century or earlier. With these exceptions history of placer mining in the Western States begins with Marshall&apos;s discovery of gold in northern California in 1848. During the next twenty years placers were found in all of the principal mining districts that are known today. The richer deposits were soon mined out but a relatively large production was maintained from the leaner deposits chiefly by hydraulic

Jan 1, 1933

By Charles A. Kelliher

In November of 1957, the Aliquippa Works started operation of the third basic oxygen furnace shop in North America. This high speed basic steelmaking method provided a very economical increase in capacity at the Works. The success of these two (2) 81-ton furnaces led to the construction of a second B.O.F. shop, producing heats of 230 tons at J&L&apos;s Cleveland Works in 1962. The experience gained operating both shops provided the background for the design of the new steelmaking complex at the Aliquippa Works. This new complex consists of a three (3) furnace shop with two (2) furnaces blowing alternately producing heats ranging from 120 to 207 tons. This variation in heat size is predicated on the requirement that approximately 20% of the shop production will be used to supply steel to a six (6) strand casting machine, producing 4&apos; through 7" billets. The new B.O.F. shop has replaced all other steelmaking units including the #1 Shop, where operations were discontinued in September of 1968. With the advent of the strand casting facilities in September of 1969, many of the standard shop practices had to be changed to compensate for higher tap temperatures, longer handling times, and reduced ladle availability. The subsequent changes in these areas led to the evolution of the strand cast ladle practice which is described in this paper.

Jan 1, 1972

By W. M. Bertholf

IN 1945 tests were made in the coal washery of the Colorado Fuel and Iron Corporation, at Pueblo, Colo., to determine the value of the Humphreys spiral. So far we have demonstrated that it is of definite value to us in rewashing a portion of our table middlings; and we are fairly certain that this is not necessarily the only place in which it can be used to advantage. Because of manpower and material shortages, experimental work has been discontinued for the present. Three of the spirals are being installed for use in rewashing the middlings, and testing and experimental work will proceed when this installation is completed. All evidence secured so far points to the fact that the spiral can make an effective separation of heavy material below 8-mesh; but that it is ineffective in removing larger, heavy material. This, of course, will limit its use to fine coal or a classified feed containing no heavy material larger than 8-mesh. In considering the results of our tests, it should be noted that the feed was our table middling, and that any real separation of this material is a "moral victory," as there is little material that could be properly called coal and practically no heavy rock, the consequence being that previous attempts to clean the middlings have not been at all successful. Several articles dealing with the spiral and its use in treating heavy minerals have already been published,1 but for the benefit of those who have not seen these we include a brief description of the spiral and of the way it operates, taken from Bulletin 4 of The Humphreys Investment Co.: The Humphreys Spiral Concentrator consists of a spiral conduit of modified semicircular cross section. Ore pulp is fed to the top and, as it flows downward, the heavier particles concentrate in a band along the inner side of the pulp stream (Fig. I). Outlets for removal of products are located at the lowest points in the cross section of the conduit. Wash water, added at the inner edge of the stream, flows outwardly across the concentrate band. The width of concentrate band removed at the outlets is controlled by adjustable splitters. Concentrate is usually removed from the upper portion of the spiral and middling from the lower portion. Tailing is discharged from the lower end. Tests are usually made in closed circuit, since this provides a maximum of information with a minimum amount of sample. Fig. 2 shows the spiral set up for closed-circuit testing, and gives a good idea of the general arrangement of such an installation. The small cyclone separator is used to provide clean wash water without introducing additional water into the circuit.

Jan 1, 1946