Search Documents

CONTENTS PAGE ANDERSON, ARVID E., and CAMERON, FRANK K.-Recovery of Copper by Leaching, Ohio Copper Co. of Utah. Discussed by Thomas B. Brighton, H. C. Goodrich, Arvid E. Anderson, Thos. P. Billings, Frank K. Cameron 2 BEESON, J. J.-Mining Districts and Their Relation to Structural Geology. Discussed by Charles Keyes, Chas. A. Porter 4 DOBBEL, CHAS. A.-Deep-hole Prospecting at the Chief Consolidated Mines. Discussed by G. W. Crane 10 CRANE, G. W.-Notes on the Geology of East Tintic. Discussed by G. W. Crane, H. E. Havernor, N. O. Lawton 11 SACKETT, B. L., BARDWELL, CARLOS, JACOBSON, SIMON, and JENSEN, N. H. Lead Smelting in Utah. Discussed by D. W. Jessup, B. L. Sackett, E. H. Laws 13 BARDWELL, E. S., and MILLER, Roy H.-Pulverized Coal as Fuel for Copper Refining Furnaces. Discussed by L. D. Anderson, E. S. Bardwell, C. P. Crawford 15 WIGTON, G. H.-The Chief Consolidated Volatilization Process and Mill. Discussed by Thomas Varley, S. G. Olmstead, V. O. Lawton, O. C. Ralston.... 16 JESSUP, D. W.-Evolution in the Preparation of Ores for Lead Blast Furnaces. Discussed by W. Spencer Reid, D. W. Jessup, Carlos Bardwell 19 ALLEN, H. P., and MADGE, WM. C.-Chloridizing Mill of the Standard Reduction Co. Discussed by Thomas Varley, H. R. Hanley, H. P. Allen, George H. Dern 20 TUCKER, E. L., and HEAD, R. E.-Effect of Cyanogen Compounds on Floatability of Pure Sulfide Minerals. Discussed by Blarney Stevens 24 Mix, B. E., and BARKER, L. M.-Method of Unloading Ores and Coarse-crushing Practice at Magna Plant of Utah Copper Co. Discussed by W. C. Madge,B. E. Mix 25 KEIGLEY, C. T.-The New Byproduct Coke Plant of the Columbia Steel Corporation. Discussed by W. M. Grant, C. T. Keigley, A. C. Feilder 25 JACKSON, P. W.-Blast Furnace Plant of the Columbia Steel Corporation. Discussed by W. R. Phibbs, H. M. Henton 26 OLDRIGHT, G. L., KEYES, H. E., and WARTMAN, F. S.-Production of Ferric Sulfate and Sulfuric Acid from Roaster Gas. Discussed by G. D. Van Arsdale William E. Greenawalt, G. L. Oldright 27 MAZANY, M. S.-Braden Copper Company Caletones Smelter. Discussed by A. B. Young, G. L. Oldright 36 HARRINGTON, D.-Safety Methods in Utah Coal Mines. Discussed by Edward K. Judd, Otto Herres, Benedict Shubart, A. C. Watts, D. Harrington 36

Jan 12, 1925

By W. Spencer Hutchinson

IT is the purpose of this paper to describe a method used to determine the corundum contents of samples of hard crystalline gneiss containing both corundum and red garnet. A chemical analysis of the rock for alumina would not fix the amount of corundum because at least three other constituent minerals of the rock, mica, feldspar, and garnet, contain alumina combined with silica. Following are the principal minerals found in the samples, together with their specific gravity and hardness as given by Dana:

Jan 6, 1913

By Robert M. Jimeson, James M. Grout

The competitive market potential for solvent-refined coal is estimated and the market advantages are enumerated. Markets are possible in combustion, railroad locomotion, and carbon electrodes. The combustion characteristics are consistent with expected air pollution restrictions on the emission of sulfur and particulate matter. A market potential of sufficient size exists to support the initiation of solvent refining in the United States. The market analysis should help fuel producers determine the advisability of their undertaking solvent refining of coal.

Jan 1, 1972

By Roswell Johnson

A CANVASS of the various institutions known or suspected to be giving courses dealing with petroleum and gas revealed the courses listed in the accompanying table, which includes a summary of the number of class hours, as a whole, of the courses listed. It will be observed that the situation is grati-fying. Courses are presented in different institutions in the main geographic sections of the country, so that students have no difficulty in obtaining education in this field. The committee believes that the courses that are offered in many institutions are so inadequate in amount as to make it unwise for students who have not had additional work to consider themselves trained in this field. We strongly urge the few schools now presenting the most adequate courses to develop these more fully, bringing their work up at least to 300 hours, and let other schools concentrate their energies in other fields.

Jan 6, 1922

By H. E. Howe, A. A. Smith

The creep properties of lead alloys have been studied by a number of investigators but most of the work has been done on extruded material and the amount of data available on rolled alloys is surprisingly limited. Greenwood1 and his collaborators investigated various rolled commercial leads containing relatively small amounts of impurities, Phillips2 likewise studied rolled commercial leads, although he did include a few alloys— such as tellurium lead and one per cent antimonial lead. But as far as the authors are aware no data on the creep properties of so-called "hard leads"-—i.e., containing from 4 to 8 per cent antimony—have been published. In this paper some data are presented on a few antimonial lead alloys and compared with a copper-bearing lead. Preparation OF Specimens All the alloys used in this investigation were cast at a temperature of 400°C. into an open cast-iron mold preheated to Ioo°C., the resultant casting being % by I by 10 in. The copper-bearing alloy was cold-rolled by 10 per cent passes to a thickness of 0.100 in. Creep specimens 16 in. long were prepared by clamping the strips between wooden blocks and machining the edges of the strips parallel by means of a plane. Careful manipulation gave parallel specimens with no reduced section and with a minimum of distortion. The antimonial lead castings were hot-rolled in 10 per cent passes at a temperature of I50°C. to a thickness of 0.400 in., the heating being carried out in an electric oven after each pass through the rolls. After the castings had been broken down to 0.400 in., they were allowed to cool to room temperature and then cold-rolled to 0.100 in. with the usual Io per cent passes. Sufficient time was allowed after each pass for the strips to cool to room temperature. The apparatus and method of measuring strain have been adequately described in a previous paper3 and essentially the same practice was used in obtaining the present data. Time-extension curves for only two alloys are given, since these are typical of all. Figs. I and 2 show the time-extension Curves for the copper-bearing alloy A at 30°C. and loo°C., and Figs. 3 and 4 show

Jan 1, 1945

Jan 1, 1969

By Harry H. Power

WHILE the attention of all engineering branches is focused today on changes and improvements in the several curricula, we are concerned here with the many questions arising in industry and college concerning the preparation for the petroleum engineering profession. The succession of problems confronting the petroleum engineer demands a degree of versatility not ordinarily encountered in other professions. As a consequence, the student cannot acquire mastery of all the several engineering branches represented in field practice, and as an alternative, he has learned to appreciate the value of thorough training in the basic or fundamental sciences as a preliminary foundation for professional work. While our attention is directed primarily to the training of engineers in educational institutions, it is necessary that the ultimate education of the professional engineer be kept in mind. It is apparent that his success as an engineer is limited not only by his educational and job experience, but by his native endowments: mentality, personality and health. The engineer's lack of job experiences often proves as much a handicap as the lack of adequate college training. If the final product proves to be satisfactory, both industry and technical institutions are to be congratulated. However, if the product is found wanting, the one most responsible should be apprehended. FITNESS FOR PROFESSION For the most part, students of engineering colleges have had their interests in applied science awakened at a relatively early age. Many of them entered college as a convenient means of acquiring a technical education, but undoubtedly would have had better prospects in a shorter program offered by institutions of noncollege grade. The activating motive of practical interest is also strong in students suitable for college training, but in many cases an intellectual interest must be awakened in order that it may survive graduation. Numerous engineers believe that this progressive process of selection and determination of career aims is one of the essential services rendered by the engineering colleges. Industrialists, who are more interested in quality than quantity of petroleum engineering graduates, have pointed out the good that should result if more emphasis were given to the work of eliminating the misfits. They also point out the protective measures that have been taken by other professions for the betterment of professional standards. Mention has been made of the beneficial results to be obtained by collective determination of the market for the products of engineering schools, particularly in that the students unsuited to the profession would have an opportunity to prepare themselves for employment more suited to their personalities and other qualifications. In the event that such a system of coordinated personnel direction is developed by the

Jan 1, 1941

By Alan K. Burton

The number of trucks required to perform a certain task is a function of the productive capability of one independent truck and the total tonnage required. Hourly productive capability of one truck is the product of trips, or cycles, per operating hour and effective payload. One cycle is made up of load, dump, and travel time, the sum of which comprises theoretical cycle time. This time is then derated by a productivity factor, giving an average effective cycle time which is used to calculate the number of cycles per hour. Rated payload is the truck's designed tonnage, while effective payload is the average amount that is actually carried. Manufacturers, particularly of the larger trucks, produce various body sizes designed to carry materials of different densities. However, it is not always possible to carry the rated payload because the material might be lighter than expected, a body of the required size cannot be produced, or because of spillage on particularly steep grades.

Jan 12, 1975

The German Kaiser is employing the keenest engineering talent of his own and allied empires in his attempt to defeat the world. American employers are paying engineers such attractive salaries that voluntary enlistments of high class technical men in the United-States Army, are below requirements. This deficiency is also probably due in part to the lack of proper information concerning the engineering branch of the service. Few civilians know that it is possible for them to perform in the Engineering Corps almost exactly the same kind of work as that in which they are now engaged. The best results in any organization are obtained only when the energy of every man in it is concentrated along the line for which he is best suited by natural ability, education, and training. It. is more important to have the right man in the right place in our Army, where lives of men are at stake, than it is in any business enterprise. The First Replace meat Regiment of Engineers was organized at Washington Barracks, D. C., on Dec. 14, 1917, with the express idea of accomplishing this. end. Its specific, purpose is to keep all engineering units of the Army at full enlistment strength during the period of this war. This regiment has not only the responsibility of finding men to fill depleted ranks, but it must also fit them to step into the work of trained, efficient and disciplined soldiers. The preliminary work of the recruit is first a thorough training in military drill, for the engineer soldier must be prepared to lay down his shovel and take up his rifle at any time. Infantry drills gradually give way to engineer work and more specific technical training. The. engineer soldiers must know how to tie knots and lashings, to build spar and truss bridges, to construct revetments, dig trenches, place wire entanglements, construct machine-gun emplacements, build pontoon bridges, and to construct roads: They must, also know the methods of demolition, sapping, and mining. Specialized training in lithography, zincography, surveying, mapping, photography, carpentry, blacksmithing, electricity, and machinery, are also given to those qualified for further training in any of these branches. Engineers are called upon to perform such a wide range of work that practically every man with any technical training or mechanical ability can find a place in this organization. Every male citizen in the United States who is physically fit, and between the ages of 18 and 21, and 31 and 40, is eligible to join the regiment by voluntary enlistment.

Jan 5, 1918

By W. S. Cavender

The Round Mountain mining district, Nye County, Ne- vada, was discovered in 1906 on claims owned by Lewis D. Gordon. Initial mining operations uncovered gold veins of spectacular richness, and within a few days of discovery, Gordon sold his controlling interest for some $87,000. From this sale emerged the Round Mountain Mining Co., predecessor of Nevada Porphyry Gold Mines, Inc., the latter destined to become the major property owner in the area. Vein mining in the district continued sporadically into the early 1930s, yielding 9.3 Mg (330,000 oz) of gold plus substantial silver credits from approximately 626 kt (690,000 st) of ore. In addition to the lode deposits, the early miners recognized the placer potential in the alluvial fan material accumulated around the west and north sides of Round Mountain itself. Intermittent placer operations were carried out for a number of years, and in the 1940s and 1950s, Round Mountain Gold Dredging Co. worked the placers under a lease from Nevada Porphyry Gold Mines. The last placer operation terminated in 1959 when it, like some of its predecessors, proved uneconomic. Total placer production for the district is estimated at 3657 km (4 million yd) of gravel containing 59 Mg (210,000 oz) of gold and possibly 2.0 to 2.3 Mg (70,000 to 80,000 oz) of silver. Round Mountain is a small hill situated on the east flank of the Toquima Range in central Nevada. The hill is com- posed of relatively flat-lying Tertiary rhyolitic ash flow tuffs, which overlie Paleozoic metasediments and Cretaceous granites. Throughout the surrounding Round Mountain mining district, most of the known gold ores occur in the tuffs, although the metasediments and granites are also mineralized. Mineralization is structurally controlled, principally by a series of northwest-trending shears and shattered zones. Vein, stockwork, and disseminated ores occur, usually containing simple quartz-pyrite-gold mineral assemblages. The gold itself is electrum, having a silver content of 30% to 40%. In September, 1967, Elwood Dietrich, a prospector and mine promoter, obtained a purchase option on the 4452 ha (1 1,000 acres) of mineral rights held at Round Mountain by Nevada Porphyry Gold Mines. The original option had a buy-out price of $1 million and was established through Dietrich's friendship with officers of Nevada Porphyry. In April, 1968, Dietrich conveyed his option to Ordrich Gold Reserves Co., a partnership created by a group of west coast investors, mostly employees of the airline industry. There- after, Ordrich invested considerable funds in trying to test and develop the property, but soon recognized the need to seek financial and technical support from the mining industry. In December, 1968, Dietrich contacted Wayne Cavender, then Regional Geologist, Southwest, for Copper Range Exploration Company (CRX) in Tucson, Arizona, and made a data presentation. Shortly thereafter, Cavender was appointed Manager of Exploration and Chief Geologist for Copper Range Co. (parent company of CRX), New York City, and he asked C. Phillips Purdy, CRX Regional Geologist, Northwest, to make an initial property examination. Purdy's one-week field study took place in March, 1969, and resulted in a recommendation that CRX pursue its investigation of the property. The presence of low-grade gold mineralization in both the alluvial gravels and in the bedrock was verifiable, but the placer was deemed to have the greater immediate economic mining potential. At that time, gold was in the $1.41/g ($40 per oz) price range. Working from Purdy's information, Cavender decided to attempt acquisition of the property, and the first in a long series of negotiations was initiated with Ordrich. Basically, CRX felt that the placer had a promising potential for several reasons, including (I) past operators had recovered free gold but not the gold contained in the pebble fraction of the gravels; (2) past operations appeared to have been ineffectively designed or managed and not costefficient; and (3) the price of gold appeared to be poised for an upward move. Negotiations with Ordrich were prolonged and difficult, with CRX competing against several ma* mining companies, but finally an agreement was reached, effective June I, 1970. Gold was then back to $35. It is believed that, in

Jan 1, 1985

By T. G. Richardson, F. M. Perkins

In the recent paper of Richardson and Perkins entitled "A Laboratory Investigation of the Effect of Rate on Recovery of Oil by Water Flooding,"' the authors found very little appzrent effect on oil recovery of having free gas saturation present prior to water flooding in unconsolidated sands. We agree that the effect in this particular system was small but do not feel that the data presented should be regarded as disproving work of others which has shown an appreciable effect. The authors do not make such a claim, but neither do they advance an explanation of the difference. In our experience the following factors must be carefully considered when studying the relation between residual oil saturation after water flooding and initial free gas saturation: (1) the magnitude of the inherent residual oil saturation, i.e., the residual oil saturation with no free gas; (2) the increase in oil-water viscosity ratio with pressure lowering if the gas saturation is obtained by solution gas drive; and (3) the oil shrinkage which occurs with pressure lowering and gas evolution. The system studied by Richardson and Perkins gave residual oil saturations as low as 20 per cent without free gas present, and one should perhaps not expect much further lowering. As an illustration of the magnitude of the effect when the residual oil saturation is inherently higher we submit the accompanying figure. These data were obtained on an unconsolidated sand under elevated pressure in a system similar to the one described by Richardson and Perkins. Gas saturation was established by gas drive before water flooding. The viscosity ratio was 600:1 under the conditions of the displacement. Here the gas was extremely effective in reducing residual oil saturation. This fact was also indicated by Kyte, et al.2 Their plots of residual oil saturation vs initial gas saturation show trends of greater free gas effect with higher oil viscosities. The pressure-dependent effects were not discussed by Richardson and Perkins. They should be separated from the free gas effect if the objective of the study is a correlation of residual oil saturation vs initial free gas saturation. The increase in oil viscosity when gas is released from solution tends to increase residual oil saturation. This effect is rather small in the viscosity range of kerosene. A Buckley-Leverett calculation, assuming an increase in viscosity ratio from 1.2 to 1.8, indicates an increase in residual oil saturation of about 1 per cent of pore volume. Thus, one would expect this system, if operated at constant viscosity ratio, to show a slightly greater free gas effect. As Dyes- as shown, oil shrinkage can offset the beneficial effect of free gas on waterflood oil recovery, if the gas saturation is established by depletion. Since

Jan 1, 1958

By E. T. Dumble

Discussion of the paper of E. T. DUMBLE, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. .1623 to 1638. E. L. DEGOLYER, Norman, Okla. (communIcatIon to the Secretary*).-Referring to Mr. Dumble's description of the stratigraphy of eastern Mexico, I should like to question the classification of the ?Papagallos? or ?Mendez? shales as being of Cretaceous age and the so-called overlapping of the Papagallos or Mendez shales by the Alazan shales; the classification of the San Felipe series as Cretaceous, and the correlation of the San Felipe series with the San Juan limestones. Mr. Durable apparently recognizes the continuity of the great shale formation by his use of the terms "Papagallos" and "Mendez," as equivalent and interchangeable, since the Papagallos Hills in the State of Nuevo Leon and Mendez Station in Northern Vera Cruz, localities at which the shale formation outcrops, and from which the formation names are taken, are approximately 250 miles apart and on opposite sides of the Tamaulipas barrier. The Papagallos shales (evidently referring here to the northern extension only) are said to be non-fossiliferous and no reason for .their Cretaceous classification is given, though in a previous article' they are classified as Cretaceous because at their northernmost outcrop they "have the same relation toward the overlying Tertiary that the Escondido (Cretaceous) has through its whole extent." The Alazan fossil locality was found by me and the first collections from it were sent to Dr. Dall; about 17 species of marine invertebrates were recognized by him, the fauna noted as having a distinct Pacific tincture, and the age of the formation from which they cause pronounced lower Eocene. The outcrop of the shale formation has been traced continuously from this point by me and my assistants into the Panuco River region, where Eocene fossils are reported at a depth of 1,810 ft. in a well at Topila.2 From Topila the formation has been traced continuously north to the Padilla-Jiminez region in Central Tamaulipas. Lithologically, the formation is fairly constant and though I am only generally acquainted with it north of the Padilla-Jiminez region, until definite evidence of the Cretaceous age of the Papagallos shale in its type localities, or of an overlap, is available, it seems to me more logical to consider the shale formation a single stratigraphic unit of Eocene age.

Jan 12, 1915

YEAR OF ELECTION 1913. FRANK DAWSON ADAMS Montreal, Canada. 1921. WILLIAM CUTHBERT BLACKETT Sacriston, Durham, England. 1923. GELASIO CAETANI Rome, Italy. 1929. TAKUMA DAN Tokyo, Japan. 1920. HENRY STURGIS DRINKER Merion Station, Pa. 1922. FEDERICO GIOLITTI Torino, Italy. 1906. SIR ROBERT A. HADFIELD London, England. 1928. JOHN HAYS HAMMOND New York, N. Y. 1928. WILLIAM BOYCE THOMPSON Yonkers, N. Y. 1921. FRANK WILLIAM HARBORD London, England. 1917. HERBERT HOOVER Washington, D. C. 1905. HENRI LECHATELIER Paris, France. 1921. C. MCDERMID London, England. 1913. EZEQUIEL ORDONEZ Mexico City, Mexico. 1909. ALEXANDRE POURCEL Paris, France. 1911. ROBERT H. RICHARDS Cambridge, Mass.

Jan 1, 1923

By Donald A. Cumming

Since the first major mine development, the company has continually looked for ways of improving drifting methods. The planned increase in production to 60,000 tpd, and the lack of trained personnel, requires new development methods to maintain this high production rate. In order to finish the drifting on the 2015 and 2075 levels, a total of 59,000 ft is required, or two years at the present rate.

Jan 4, 1972

By Nicholas J. Grant, Hanna Ibach, Bill C. Giessen

The system Ta-Rh was investigated over the entire comnposition range using metallogvaphic and X-ray techniques as well as thermal analysis. Terminal solubility limits, solidus temperatures, and the crystal structures of two new intermediate phases were determined. There are five intermediate phases: o, tetragonal, isostructural with o(Fe-Cr); a1, orthorhomnbic : a2, orthorhombic, isostructural with CozSi; 0 3, a high -temperature phase of unknozun structure; and a TaRh3, cubic, AuCu3 structure. a, aL, a,, and a melt peritectically; and a TaRh, has a maximum melting point. Five peritectic and one eutectic reactions occur. THE Ta-Rh phase diagram has not been fully treated in the literature; however, two inter metallic phases have been described.&apos;-&apos; This study attempts to work out the diagram covering the details of phase boundaries as well as the crystallography of the intermediate phases. EXPERIMENTAL METHODS Starting materials were tantalum powder of 99.8 pct purity, supplied by National Research Corp., Cambridge, Mass., and rhodium powder of 99.9 pct purity, supplied by Bishop Co., Malvern, Pa. Analyses as given by the manufacturers are presented in Table I. In addition to the spectroscopic analysis, an oxygen analysis has been made of the tantalum powder. After preliminary trials, the standard procedure employed in making the alloys was as follows (see Ref. 4 for further details). The powders were weighed, mixed manually, compacted under 16,000 psi, and arc-melted at not more than 500 amp under thoroughly titanium gettered welding-grade argon of 400 mm Hg pressure. The gettering process was repeated after each melt. It had been shown previously5 that under these conditions no oxygen pick-up exceeding 0.001 pct in a hafnium button could be detected. The buttons, ranging from 5 to 10 g in weight, were inverted or, if possible, crushed and remelted three times. Melting presented no difficulty, except for tantalum-rich al- loys, which showed considerable spashing during melting. The average weight loss of 1 wt pct rose to 2.5 wt pct in these cases. Subsequent melting, however, resulted in losses of less than 0.1 wt pct. The melts obtained frequently showed small in-homogeneities, mostly in the tantalum-rich part of the system below 25 at. pct Rh. This was not due to insufficient blending of the elements, but to crystallization taking place from the cooled bottom. This condition was not improved by further re-melting; therefore the following precautions were taken. Cross sections of as-cast buttons were made. For the investigation only buttons were used where these inhomogeneities did not exceed 1 at. pct (estimated from the amounts of haSeS resent). In addition, only the center portions of such buttdns were utilized to minimize errors. Smaller buttons showed smaller concentration gradients and were used as a check. Finally, all alloys were homogenized to eliminate coring (see below). After this, the error in alloy composition due to inhomogeneity was cl at. pct. In order to confirm the concentrations of the alloys and to provide an impurity check, wet-chemical analyses and oxygen-fusion analyses of four key alloys were carried out. The results, together with the concentrations as calculated with the weight balance method, are presented in Table 11. It was found that for three alloys the agreement is very good (< 0.2

Jan 1, 1964

By L. D. Stamp

In view of the comprehensive accounts which have appeared in recent years of the oil fields of Burma, Assam and the Punjab,&apos; this brief account will be restricted to an outline recapitulation of the position of the fields and a note on progress and developments in the last two or three years. It is actually peculiarly difficult to give an account of recent developrnents in the oil fields of the Indian Empire. The companies naturally are compelled to make a return to the Government of India of oil produced. These figures are published annually (about 10 months later) for each administrative district (which may include more than one field) where oil is produced, in the Annual Review of the Mineral Production of India (Records of the Geological Survey of India). Some details of recent developments may be given in the Annual Report of the Geological Survey of India (also published in the Records), but otherwise the companies tend to preserve a policy of extreme secrecy. Some of the smaller companies usually publish wellhead production month by month in order to encourage their shareholders when such figures are encouraging, but the larger companies do not necessarily even give figures of production in their annual reports to shareholders. Occasionally details of new tests, new machinery, and so on, leak out through the daily or weekly press in India, but, except for generalized official statements, no details :ire available as to the number of new wells, depths, wells abandoned, or other figures which are common property in other parts of the world. In the country itself the geologists preserve the utmost secrecy, and at times quite a serious system of espionage is developed. Of recent years there has been a slight tendency towards the pooling of experience, but actually the Indian Empire, particularly of course Burma, where there is a

Jan 1, 1933

By D. A. Flanagan, B. L. Landrum, P. B. Crawford, B. C. Norwood

Herern is described a heat conduction model which has been developed to predict the pressure distribution within a reservoir being subjected to rrnsteady-state depletion. Although potentiometric models have been widely used to study reservoir pressure distribution, their application is limited to the study of steady-state cases. Electrical analyzers may be used to study unsteady-state phenomena, but their application and simulation have certain limitations. Much of the now accepted theory of unsteady-state fluid flow in porous media has evolved from previous heat conduction knowledge. An analogy between the flow of fluid in an unsymmetrical reservoir and con-duct ion of heat in a similarly shaped unsymmetrical metal plate is made to show adaptability of the hear conduction principle to transient reservoir cases. A description of the model and necessary instrumenrarion is included. Data show influence of well location on pressure distribution during unsteady-state deple[ion. Application of results is made to a hypothetical reservoir and to a reservoir located in an irregular aquifer. INTRODUCTION Development of methods for predicting behavior of petroleum reservoirs has resulted partially from adaptation of electrical and thermal flow concepts to the flow of fluids through porous media. Extensive investigation of electrical and thermal flow problems has resulted in mathematical solutions applicable to many reservoir problems. The relative ease of measuring electrical flow has brought wide acceptance of the use of the potentiometric model to study certain field problems. Potentiometric models are restricted to the study of steady-state conditions because of the instantaneous response of electrical flow to changes in the applied potential. The electrical reservoir analyzer has been one of our most useful instruments for studying certain phases of unsteady-state behavior1. Other than approximation techniques, no method exists for determining pressure distribution in an irregular reservoir during primary depletion. Heat flow, like fluid flow, is inherently transient. The model described here was developed to use this transient nature of heat flow, measurable in the laboratory, to simulate transient flow of fluids in the porous medium of the reservoir above the bubble point. A metal plate shaped like the reservoir to be studied was heated by a "well" source. Temperature increase in the plate is analogous to pressure decline in the field if the field is being depleted, or pressure increase if fluid is being injected. This study is intended to determine the feasibility of using the transient nature of the heat flow to study the transient behavior of fluid flow. It is hoped that this new technique will aid in the understanding of one of the more complex phases of reservoir engineering. THE FLUID FLOW-HEAT CONDUCTION ANALOGY The similarity of the equations which describe the flow of fluids through a porous medium and the conduction of heat through a solid is well known2. Rate of flow of fluids is given by Darcy&apos;s law3. while the rate of flow of heat is given by Fourier&apos;, (I,, - KA 4T........(2) Combining Eq. 1 with the equation of continuity for a compressible liquid", i.e.,results in Expressing y in terms of the compressibility, i.e., pr = peey ,..........(5) and by expanding the exponential and neglecting higher orders of cp one can obtain

By W. H. Blauvelt

The technical and engineering problems in the manufacture of coke are today the problems of the byproduct oven. Except in a few special localitics, practically no beehive ovens have been built in the United States for the last 5 or 6 years except as renewals of old plants, and during these years the total number of beehive ovens in existence has been steadily falling. On the other hand, the number of byproduct ovens has increased from 4624 in 1911 to a total of about 7660 in operation at the end of 1917; with 2800 building, this makes a total of about 10,460 which will be in operation in 1918, or shortly thereafter. Preliminary Government estimates place the total production of coke for 1917 at 56,600,000 tons, the largest tonnage in the history of the industry. Of this 34,000,000 tons, or 60 per cent., was beehive, and 22,-600,000 tons, or 40 per cent., was byproduct coke. Some time in 1918 the production of byproduct coke should pass the beehive output, and when the byproduct ovens now building are completed the total byproduct capacity will be about 40,000,000 tons of coke per annum, which is over 70 per cent. of the record-breaking total coke production of 1917. The reasons for these changes in the coking industry are familiar to all of us, and need not be discussed here. Improvement in Oven Design Since the byproduct oven was brought to this country from Europe, in 1892, it has been radically improved, and from the point of view of American metallurgical practice it is safe to say that the American ovens arc superior to those of Europe. The points of superiority are mainly those of larger units and larger output per unit, and the greater extent to which labor-saving machinery has been introduced. The increased output is largely due to the use of silica refractory material, which permits higher heats and shorter coking time than are employed in Europe. The modern American oven will carbonize commercially more than 20 tons of coal per day, and contrary to the European idea that slower

Jan 1, 1920

By J. Blodget Britton

To the question, "Do the Pennsylvania anthracites contain phosphorus ?" asked at the last meeting of the Institute during the discussion on the metallurgical value of Western lignites, I can now give a definite answer. Through the kindness of a gentleman connected with the Philadelphia and Reading Railroad, and another connected with one of the principal ironworks on the Lehigh, there was sent to the Iron-masters&apos; Laboratory a number of samples of the coals now largely shipped from the Schuylkill and Lehigh regions. Seventeen of these I examined for their contents of ash and phosphorus, and obtained results as follows

Jan 1, 1873

By John R. Anderson, Michael B. Bever

Carbon may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,&apos; the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. Earlier Data The solubility of carbon in molten pure copper is about o.oooi pct at II00°C and 0.0004 pct at 1475°C.l Various authors2""6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range r2170 to 1245°c This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947