Search Documents

By L. Zwell, H. A. Wriedt

X-ray Lattice parameter and bulk density measurements were made at room temperature on solid solutions of nitrogen in purified a, iron, containing from 0 to 0.053 wt pct N. When nitrogen is dissolved in a, iron, the fractional increase in unit cell volume (X-ray diffraction) and the fractional increase in volume per gram of iron (bulk density measurement) are the same within experimental error. The two sets of results when averaged show that the unit cell edge of a, iron increases linearly by 3.2 X 10-2 A per wt pct N dissolved and that the partial gram-atomic volume of nitrogen at infinite dilution in a, iron is the same as it is in nitrogen-martensite, that is, 5.90 cm3. RECENT reviews17' of literature dealing with the lattice parameter of ferritic iron-nitrogen alloys indicate that the dilating effect of dissolved nitrogen on the bcc unit cell of a iron is not known with confidence. Five investigations3-7 either revealed no effect of nitrogen or were inconclusive. Among other investigations, where quantitative data were obtained, the results of Osawa and Iwaizumi8 indicate too large an effect, and those of Eisenhut and Kaupp9 show the lattice parameter of ferrite varying with the nitrogen content at concentrations far beyond the known solubility limit. It is not clear in Burns'10 data what value should be used for the lattice parameter of nitrogen-free ferrite in calculating the dilation. Burdese11 shares with Burns the shortcoming that the iron-nitrogen alloys were solution-treated and quenched with undissolved nitride present. The consequence is that the un- certainties in the solubility limit1 are added to those in the lattice parameter measurements when the variation of lattice parameter with nitrogen content is computed. For a system of such widespread interest, we felt that a new investigation was merited. Both X-ray diffraction and bulk density measurements were used to determine the dilation of the , a iron lattice by dissolved nitrogen. EXPERIMENTAL PROCEDURE Material. The bulk density and X-ray diffraction experiments were both made with specimens of a purified iron (denoted as "B iron")- from Battelle Memorial Institute. The impurity contents were as follows: As, C, Cu and Pb—50 ppm; Ag, Al, Co, Ga, 0, Ti-11 to 50 ppm; B, Be, Ca, Cd, Cr, Mg, Mn, Mo, N, Ni, S, Sb, Si, Sn, V, W-10 ppm or less. The vacuum-cast ingot was hot-forged and annealed. Pieces of the forged stock were machined and cold-rolled to give strip stock 0.08 and 0.002 in. thick for density and for X-ray measurements, respectively. Preparation of Specimens. Starting with a piece of the cold-rolled iron stock, the general sequence of operations, after an initial recrystallizing anneal, was to measure the density or lattice parameter, nitrogenize, remeasure the property, age or denitrogenize, and again measure the property. Duplicate analyses for nitrogen were made by a modified Kjeldahl method on portions of the actual density specimens and on pieces nitrogenized to equilibrium alongside the X-ray specimens. Annealing of the density specimens was performed by sealing the pieces with the as-rolled surfaces removed by filing into evacuated "Vycor" capsules and treating for 1 hr at 750°C followed by furnace cooling. (TO check the effect, if any, of annealing procedure, a specimen also was

Jan 1, 1962

Kaolin deposits in Georgia lie in a belt that stretches across the central part of the state from Alabama to South Carolina. In 1977 the state's kaolin production was an estimated 4.58 million tons (5.05 million st) or 77% of US production. While mining methods vary, stripping contractor W. F. (Billy) Jackson of Wrightsville, Ga., depends on a fleet of 18 twin-engine elevating scrapers to move the hulk of overburden and clay. Owner Billy Jackson explains that the soil in this part of the state is perfect for scraper operation; overburden ranges from Georgia red clay to a sandy gumbo material. Apart from some shale, very little rock is encountered, thus eliminating any blasting re¬quirement. Most of the material can be removed with cutting edge teeth or with drop center blades.

Jan 6, 1978

By N. A. Stockett

SOUTHEAST Missouri is the largest and oldest lead-producing district in the United States. For the year 1941, the statistical picture of pig-lead production, stated in short tons (partly estimated by the Engineering and Mining Journal) is as follows. [Tons World production 2,000,000 United States production 460.000 Southeast Missouri production 242,000] The consumption of primary lead in the United States in 1941 was approximately 900,000 tons, or almost double the country's production. The largest previous year's consumption in the United States was 718,000 tons, in 1926. The largest quantities of lead are used for cable sheathing, storage batteries and white lead. During 1941 tetraethyl lead for auto and aviation gasoline consumed 50,000 tons of lead. The entire lead production of Southeast Missouri is now mined by the St. Joseph Lead Co., whose dominant position as the largest producer in the United States of lead directly from ores is best shown by the fact that in 1941 it produced approximately 31 per cent of the lead production of the United States from its mines in southeast Missouri, where 22,000 tons of ore, averag¬ing over 3.00 per cent lead, is mined per working day. It is known that lead was mined at Mine La Motte, Madison County, Missouri, by Renault in 1723. Other white men and Indians probably did some mining prior to that time. Since 1865, the recorded production to Jan. 1, 1942, shows that the St. Joseph Lead Co. and the various other companies that have operated in St. Francois County mined lead ore, which, after milling and smelting losses produced 5,00,000 short tons of pig lead. About 95 per cent of the present lead production of Southeast Missouri is mined in St. Francois County. The northern part of this area is 60 miles south of St. Louis. The remainder of the lead is obtained at Mine La Motte, about 25 miles southeast from the center of the producing area in St. Francois County. PROSPECTING In this district, most of the ore is discovered by surface and underground diamond drills and by prospect drilling underground with rock drills. Each 2-ft. length of the cuttings from these Jackhamer prospect holes is assayed for lead. These holes are marked and the records are entered on maps. It has been found that close drilling--100-ft. centers of holes, and sometimes less-is necessary in order to locate most of the smaller commercial ore bodies, many of which previously had been missed by drilling the areas with holes spaced 200-ft. centers or more.

Jan 1, 1943

By Alfred Brooks

Introduction PETROLEUM seepages are known in Alaska at four localities, all on Pacific seaboard. These, named from east to west, are Yakataga, Katalla on Controller Bay, Iniskin Bay on Cook Inlet, and Cold Bay on the Alaska Peninsula. Besides these, a petroleum residue has been found near Smith Bay on the north Arctic coast of the Territory. At Katalla, Cold Bay, and Iniskin Bay there has been some drilling for oil, and in the first field several productive wells have been opened up. Alaskan petroleum so far as its composition is known, is a refining oil, with paraffin base and low sulphur content. Most of what is known of the geology of Alaska oil fields is based on the investigations of Dr. George C. Martin, of the United States Geological Survey. A. G. Maddren, of the same service, has recently made a reconnaissance of the Yakataga oil field. The data to be here presented are chiefly taken from the following publications: G. C. Martin: The Petroleum Fields of the. Pacific Coast of Alaska, with an account of the Bering River coal deposits, Bulletin No. 250, U. S. Geological Survey, pp. 9 to 27 (1905). G. C. Martin: Geology and Mineral Resources of the Controller Bay Region, Alaska, Bulletin No. 335, U. S. Geological Survey, pp. 112 to 130 (1908). G. C. Martin and F. J. Katz: A Geologic Reconnaissance of the Iliamna Region, Alaska, Bulletin No. 485, U. S. Geological. Survey, pp. 126 to 130 (1912). A. G. Maddren: Mineral Deposits of the Yakataga District, Bulletin No. 592,. U. S. Geological Survey, pp. 143 to 147 (1914).

Jan 2, 1915

By Ingvar Janelid

DURING the last ten years, in the effort to save manpower and costs, methods of drilling and blasting in Sweden have changed and developed in a revolutionary manner. These developments have been accompanied by extensive alterations in methods of tunneling and in mining technique. Since the end of the 1940's there has been a 100 pct change-over in Sweden to the use of tungsten carbide tipped drill steel. Both investigations and practical results have shown clearly that a tungsten carbide chisel bit fastened directly on the drill steel is the most economical for Swedish conditions. This applies to drill steel up to the longest size it is practical to handle. In terms of drilling footage, durability of the drill steel and the tungsten carbide bit is generally the same. In this respect, therefore, a detachable bit offers no advantage over integral steel. Transportation of integral steel to the grinding plant, instead of detachable bits only, involves heavier work, but this is counteracted by placing grinding plants closer together or by grinding at the working place itself. The drilling rate with integral steel is higher, the trouble of changing bits is avoided, and the difficulties which always arise with joints are eliminated.

Jan 6, 1954

By Leonard Waldo

PROBABLY some of the views advanced in this paper will appear, from a metallurgical standpoint, little less than revolutionary. It is with considerable hesitancy that I venture to offer a few thoughts concerning what, seems to me to be perhaps the most important development of metallurgy since the introduction of Bessemer steel. Dr. John Percy, with that rare insight which characterizes the epoch-making man, described in a communication to the Royal Society, about 1855, an alloy of duminum and copper which he called aluminum-bronze. The name has "stuck." The term "bronze" has been so variously used that I confess I do not know exactly what constitutes a bronze; but I know that in the great materials of engineering simplicity of composition is a cardinal excellence; and I wish to venture the suggestion that aluminum-bronze is not an alloy of aluminum and copper in any such sense as the compounds of tin and zinc with copper (except the copper-tin compound SnCn3) are alloys. There are several reasons which lead me to this view. In the first place, if a series of bars be prepared containing varying percentages of aluminum and copper, and the electrical conductivity of these bars be carefully determined, a curve of conductivity will be obtained, as shown in Fig. 1, which represents the result of such experiments. While I am not sure, at this time, that the values of conductivity shown in this diagram are wholly dependent upon the percentage of aluminum added, the assumption is a probable one; and the curve indicates that an extremely small percentage of aluminum affects the conductivity in a ratio out of all proportion to the amount of that metal. Another reason is drawn directly from experience in the foundry. If we take from the furnace a crucible containing melted aluminum and one containing melted copper, both at a little more than a red heat, and pour them together, the reaction is so intense that the

Jan 1, 1895

By Otis Hutchins

IT is intended to discuss in this paper the protection appliances used for high-temperature pyrometer installations involving the use of platinum couples and describe some of the characteristics of a new carborundum protection tube. Of all the components that go to make a complete pyrometer installation, the one given the least attention and the one about which there is the least exact information is the outer protection tube. This condition is unfortunate as much, and in some cases even the success of the equipment as a whole, depends on the proper type of protection. In the majority of cases, the installation is allowed to operate without attention until some part of the apparatus breaks clown. The outer tube is the component that usually fails and, more often than not, the failure causes breakage of the porcelain protection and ruin of the couple. This condition should be recognized and studied as it has a very important bearing upon the upkeep cost of pyrometer equipment. The cost of the outer protection tube is small compared with the cost of the platinum couple and procelain protection and it would well repay users of this type of equipment to replace their outer protection tubes at certain definite periods, which experience shows is necessary to prevent destruction of the platinum. Speaking generally, platinum thermocouple equipment is used for measuring temperatures over 2000° F. (1094° C.), and is used extensively for the control of brick and pipe kilns, glass pot furnaces, glass tank furnaces, heat-treating furnaces, open-hearth furnaces, and forge furnaces. A satisfactory protection tube must be sufficiently refractory not to soften at the maximum temperature within the furnace. It must be resistant to cracking clue to temperature changes, should be as nearly gas-tight as possible, and should be made of a material with a high thermal conductivity and great resistance toward erosion by the furnace atmosphere.

Jan 9, 1919

By Albert Williams

A large proportion of the work performed in wet-crushing silver mills is devoted to the handling and re-handling of pulp between the battery and the pans. There seems to be no generally applicable substitute for the settling-tanks, and in the present system of constructing mills the tanks involve an amount of labor which may be regarded as disproportionate and unnecessary, in view of the automatic improvements which have been introduced in other directions. This diffculty has been met, however, by Boss's continuous process, in which the pulp flows directly from the mortars to the first of a series of constantly working overflow-pans. This method has been adopted at the Noonday mill, Bodie, California; the Harshaw, Arizona; the Sierra Grande, New Mexico ; and the Prietas, Sonora. The continuous process, while giving excellent results with special ores, and under peculiar local conditions (such as a deficiency in water supply), is not, I believe, claimed to be available for all raw-amalgamating mills, notwithstanding its well-merited popularity for certain work. Some trouble has been experienced from the tendency to concentration in the pans, though this can be avoided by skilful manipulation. It has also the disadvantage inherent in combinations of distinct operations ; it requires a very nice adjustment of the water supply to obtain full battery efficiency without running the pans too thin, though the latter defect is partially compensated for by the gradual thickening of the pulp as it proceeds through the series of pans. The objection is similar to that which holds in a parallel duplex process, that of combining roasting and smelting in a single furnace, where each operation is injuriously affected by the necessity of fitting it in with another and entirely different one.

Jan 1, 1883

By R. W. Raymond

There is apparently no end to the doubts, inconsistencies and absurdities in which the courts of our mining States and Territories are involved in their attempts to apply to conditions of ever-increasing complexity the provisions of our anomalous mining law. In previous papers, I have called this statute " the law of the apex," because it based upon that vague, novel and mysterious condition the most important grant of title. But the apex is scarcely a more essential feature than the end-lines and the side-lines; for the rights which it may confer may be limited in various ways by these; so that we have, in many a case, the most ridiculous result that the United States, in return for the money of a citizen, conveys to him with much solemnity, under its broad seal, nobody knows what, bounded nobody can tell how. A decision recently made at Butte by Judge De Wolfe, of the United States District Court of Montana, in the case of King et al. vs. The Amy and Silversmith Mining Company, furnishes a fresh illustration of this criticism. The diagram on the following page, constructed without precise regard to courses and distances, simply to assist in the statement of the essential features of the case, will, 1 hope, make clear the principles . involved : The plaintiff occupies a location (the Nonconsolidated) adjoining on the north the defendant's location, a b c d (the Amy), and the disputed mining-ground lies, let us say, in depth under the point W, that is, on the dip of the vein, VD, but not under the surfacelocation, a b c d. The defendant has the prior title, and claims this ground under its extra-lateral right. It is admitted that the apex does not cross the end-line, a d, and does cross the side-line, a b. Whether it crosses, at the other end of the location, the end-line, b c

Jan 1, 1889

By F. A., King

THE problem of the proper size and capacity of the open-hearth furnace has been a predominant issue ever since its inception some sixty years ago. The original furnaces, built in 1868 at Landore, England, were only to 3 to 4 tons capacity, and from' this there has been a steadily increasing and almost uniform rate of expansion until furnaces producing 300 tons are in successful operation today. At the end of the first half of this 60-year period, or about the year 1900, 50-ton furnaces we're common. Up to this time the problems of expansion had been largely those relating to suficient capital and the engineering development of larger units. But as 75, 100-ton and larger furnaces were proposed apprehension grew and other questions assumed leading consideration.

Jan 1, 1928

By Henry Rogatz, H. W. McCue

Oil.—During the year 1939, there were 365 oil wells drilled in the Texas Panhandle, with a total daily initial production of 130,968 bb1.— that is, 69 fewer oil wells drilled than in the previous year, with a decrease. in total daily initial production of 61,738 bbl. The total daily potential of the field on Dec. 5, 1939, as determined by the Texas Railroad Commission, was 1,344,677 bbl., an increase of 94,032 bbl. over the previous year. On Dee. 5, 1939, a daily allowable of 130,527 bbl., which was an

Jan 1, 1940

By David R. Mitchell, R. M. Fleming

MANY trends were evident in the coal industry during 1951. Some were favorable for the industry; others were not. Probably those having the most far-reaching consequences are those affecting coal's markets. The rapid dieselization of many railroads and the continued trend toward oil and natural gas for home heating has caused serious dislocations in various mining districts. Mines have been forced to close down or to work on a reduced time basis. Conversely the increased activity in the metallurgical industries has increased the demand for coking and special purpose coals, and the growing production of electric energy has increased the demand in certain areas for steam coals. The increased demand for metallurgical coal and for steam raising by the large utilities is more than equal tonnage-wise to the loss of coal to railroad dieselization and conversions to oil and gas in the domestic market. Since much of the expansion is at captive mines of large corporations, many commercial operators supplying railroad and domestic users have had their markets curtailed without any compensating demand from other sources. Feverish activity was in evidence in many areas by commercial operators attempting to find new markets. The Norfolk and Western Railway is the, only major American railroad committed to the burning of coal. It has an exceptionally good cost record. During 1951, fifteen additional modern coal-burning steam switching locomotives were authorized for construction in the company's Roanoke shops at a cost of about $1,450,000. When the new order is completed the road will own a total of sixty locomotives of the modern-switcher type, including thirty acquired by purchase last year. The Norfolk and Western today is the only American railroad building its own motive power. All of these locomotives burn coal. Production Coal production in the year 1951 will approximate 570 million tons of anthracite, bituminous coal, and lignite. Of this, approximately 7 pet is anthracite. Total production is approximately 30 million tons more than in 1950 and reflects the increase in general industrial activity. Exports are expected to be close to 50 million tons. The industrial stockpile is close to 75 million tons, the highest it has been since 1943. With the exception of the usual local stoppages the year 1951 was unmarked by labor disputes. It was a year of good labor-management relations with a negotiated wage increase unmarred by a work stoppage. This may be the beginning. of an era of sensible negotiations to find agreeable settlements of disputes without the usual protracted bickering and industry-wide strike. The United Mine Workers of America has condemned wildcat strikes, stating that in nearly every, instance proper grievance procedures have not been instituted. Government defense organizations, perhaps profiting by their experiences during World War II, are pursuing a more enlightened program with regard to the fuel requirements of the nation. Many prominent officials have stated that wherever possible coal should be considered the primary source of fuel in all defense expansion. With the increased consumption of steel by defense projects, approval of transportation facilities for liquid and gaseous fuels have been refused where these fuels would enter a coal producing area. Liquid and gaseous fuel producers also have failed to provide satisfactory evidence that they have sufficient reserves and are capable of supplying their product in adequate amounts for the periods of time required. Realization has at last become prevalent that the hydro-electric power installations in several areas are insufficient to handle increased demands.' Steam generating plants are being constructed in these areas and equipped to burn coal. Most notable of these, is the TWA area whose supplemental steam power plants are expected to consume 10 million tons of coal per year when completed. The Pacific Northwest is another area which is expected to follow the same pattern. Nearly all new steam-power generating plants are being equipped to burn coal either as a primary fuel or as an emergency measure. Metallurgical Coal The steel and other metallurgical industries are expanding rapidly to meet increased industrial demands and defense orders. Since these industries are dependent on coke, coke has had a year of high production and can be expected to break all existing records when steel-plant expansions are completed. Most notable of the expansion projects is that of the Delaware River area where the iron ore will be received by ship from Canada and South America. U. S. Steel is only one of several steel corporations that are planning on putting integrated steel producing units in this area. The Defense Solids Fuels Administration announced in December that through. November 30, 1951. 29 projects in eight states, with a total cost of

Jan 1, 1952

By C. H. Mahoney, P. E. LeGrand, A. L. Tarr

MAGNESIUM, it is now generally realized, differs in some important aspects from most other structural metals, not excepting even its close neighbors, the aluminum-base alloys. This is particularly true with respect to the effects of elevated temperatures on the two light metals when in the molten state. Aluminum, on the one hand, should not be raised above its melting point any higher than is absolutely necessary if one is to avoid danger of gas absorption and a tendency toward grain growth in the resultant casting.1 Magnesium alloys, in sharp contrast, actually benefit by being heated to temperatures considerably above their melting point. It is a commonly accepted practice to establish the desired fine grain in the industrial magnesium alloys of the aluminum-bearing group by raising the temperature of the melt after the refining treatment to some 25e C (482°F.) above the melting range. To recall briefly the typical practice for magnesium alloys, the molten metal is refined by fluxing at about 730° C. (1350 F.), and after the melt has been covered with a suitable flux, the temperature is raised to between 870°C. (1600°F.) and 930°C. (I700°F.). It is then cooled as quickly as possible to the casting temperature. This superheating, as it is called, results in a fine-grained cast metal structure which has superior mechanical properties, enhanced amenability to solution heat-treatment, and better machinability than cast metal that has not been superheated. The minimum temperature of superheating varies to some extent with the composition of the alloys to be treated and usually increases with the percentage of magnesium in alloys containing the same constituent metals.2 It should be noted that the grain-refining effect of superheating is markedly apparent only in connection with the alloys containing aluminum as an alloying constituent-the binary alloy containing r.5 per cent manganese, for example, is not refined in grain to any noticeable extent by a superheating effort. While the phenomenon of superheating is well known in the magnesium industry, the mechanism of the process has remained a mystery. During the superheating cycle something occurs that forces a fine grain upon the solidifying metal. The process has been controlled in an empirical manner, and occasionally, especially on large-scale melts, and for no apparent cause, no grain refinement is obtained from a superheating treatment. Only a few papers of importance have been published on the subject. Of these, one of the most helpful is the paper by Achenbach, Nipper and Piwowarski,3 which gives considerable data concerning the effect of superheating on various properties such as fluidity, shrinkage and hot crack formation, as well as grain size, and a discussion without any definite conclusions on the theoretical aspects of superheating. A short article by Murphy, Wells and

Jan 1, 1945

By R. E. Hoffman, R. A. Ward

The self-diffusion coefficient in high purity nickel has been measured over the temperature range 870' to 1248°C. The results are described by the relation D = 1.27 exp[—-66,800/RT 1cm2ec-1. The measured activation energy correlates satisfactorily with absolute melting point, heat of fusion, and heat of sublimation. KNOWING the rates of self-diffusion is important in the understanding of many metallurgical reactions. However, in spite of the rather widespread interest in nickel, both commercially and in fundamental investigations, no measurement of the self-diffusion in solid nickel has previously been re- ported." In connection with a program of measuring rates of diffusion in some nickel alloys, self-diffusion in pure nickel has been investigated over a rather wide temperature range by combining a sectioning technique and a surface counting technique.

Jan 1, 1957

By F. W. Lee

Historical-From the beginning of time, all ingenuity of mankind has been concentrated upon the methods of finding gold and unusual deposits in the earth. An illustration (Fig. 1) from the old treatise by Agricola, "De Re Metallica," published in 1580, will serve to show the im-plicit faith of that generation in divining methods. However, it was not until 1920 that real progress was made in prospecting by using the latest advances of the physical sciences. The public interest was stimulated by the successes of these methods on the part of commercial oper-ators, and governmental agencies received many requests for information concerning their relia-bility. There were also, in the late 1920's.high- pressure mine-promotion schemes which used geophysical methods in a very questionable manner, symbolized in Figure 2 as of 1928 by an elec-trified forked stick. Authoritative information concerning such practices for public protection was needed to curb such notorious undertakings. Dr. Scott Turner, then Director of the United States Bureau of Mines, thoroughly understood the situation and was first in the governmental de-partments to recognize the possible value of a study of modern prospecting methods. The Bureau of Mines began this investigation by employing Drs. A. S. Eve and D. A. Keys of McGill University for short periods in the summer in 1927. Their first publication [see 1 of "References" at end of paper] served to illustrate the fundamental scientific principles which underlie geophysical prospecting. This was followed by a second publication [21 giving the results of field-tests. In the light of the rapid improvements during the intervening ten years, these two papers take a historical position. Later a full-time position under Civil Service was planned by the Bureau of Mines for con-tinuous investigations and research concerning geophysics and its applications to prospecting. It was Turner's idea that. since the oil-industry had been making very rapid progress with good results, if mineral mining could also benefit to the same degree, it would be of great help to that industry.

Jan 1, 1940

By H. C. George

Since 1911, when J. L. Dunn first used compressed air for repressuring depleted oil sands in southeast Ohio, the rejuvenation of many depleted oil fields has been directly due to repressuring by means of air or gas. Developments in repressuring in recent years have resulted in its successful use in the early life of some deep, high-pressure oil fields, conserving the natural gas dissolved in and associated with the oil by returning it to the producing oil sand after it has been compressed above the existing rock pressure of the reservoir. One of the most successful operations of this type is that of the Humble Oil & Refining Co., on the DeWalt salt dome at Sugarland, Texas. I quote from a personal communication with reference to this field: "Structurally, the field is dome-shaped, having a closure of approximately 350 ft. Production comes from a sandy shale interbedded with a clean sand and lying over a cap rock which is about 3400 ft. deep on top of the structure." A feature of the operation of this field is the production of the required amount of oil with the minimum of gas production. Wells on top of the dome have high gas-oil ratios, while those down structure have lower ratios, depending upon the distance of the well from the peak. To date, it has been possible to produce the oil needed from the wells circling the dome above the water zone and below the gas zone, and in this manner the average gas-oil ratio has been kept low. The gas from all separators is turned into a gas system which serves the entire field. From this system, all drilling rigs and utilities requiring gas for a fuel draw their requirements, and the remainder of the gas (about two-thirds of the production) is delivered to a compressor plant which boosts the pressure until it can be returned to the sand at the top of the dome where the rock pressure is 1400 lb, per square inch. "The Sugarland wells produce through 2-in. tubing with a 3/8-in. choke in one wing of the well-head manifold. The pressure builds up as high as 1300 lb, per square inch on the casing while on the tubing it varies from 0 to 900 lb. per square inch, depending upon the amount of gas produced with the oil."

Jan 1, 1931

By A. Gatti

Studies were made on the system iron plus alumina. Various methods of dispersing and various amounts of alumina were used. Powder metallurgy techniques were used to produce the final product. Microstructures and some mechanical properties are presented. Alloys containing up to 16 pct alumina by weight are ductile at all temperatures tested. The ivon-alumina materials have a higher yield stress and improved creep resistance over that of pure iron. SINCE the development of SAP' an A1- Al2O3 powder metallurgy product, great interest has been shown in the development of a SAP-like structure in metals and alloys other than aluminum. The outstanding properties of this class of materials are: 1) Good creep resistance at high temperature. 2) High yield strengths and high hardness at high temperatures. 3) High recrystallization temperature. However, the lack of ductility and formability has thus far limited the applications of SAP-like materials. The following report deals with methods of dispersing A12O3 in Fe, processing of powders into rod, structures produced after processing, and mechanical properties of the iron-alumina material produced. Methods of dispersing the alumina and also the volume fraction of alumina added were varied. MATERIAL Powder Processing— Four methods of obtaining dispersions of alumina in iron were studied. 1) Oxidation-reduction of a Fe + 8 pct Al alloy. .2) Coprecipitation of Fe(OH)3 + Al(OH)3 from aqueous solution. 3) Colloidal mixing of Fe,O3 and Al2O3. 4) Colloidal mixing of Fe powder and A1,O3. Fig. 1 is a processing flowsheet which outlines the processing steps taken to produce a final extruded bar 1/4 in. in diameter and about 30 in. long. The - 100 mesh iron-aluminum alloy was oxidized by placing a thin layer of powder on an alumina plaque. The reduction step was modified to include 1/2 hr at 1000°C since the powders tended to become pyro-phoric unless sintered slightly after low-temperature reduction. Compacting was done in a 1-1/8-in.-diam pressing die. The slugs produced averaged 1 in. in length. The billets were encased in low-carbon steel cans shown schematically in Fig. 2. The blank is included for structure and property comparison purposes. TESTING PROCEDURE All tests were made on as-extruded material.

Jan 1, 1960

By W. S. Landis

IN brief, this is the story of an attempt to Americanize a process originally developed in Europe. The story will be recited in two sections, the first dealing with the process as developed by the European engineers; the second containing the improvements and modifications of American origin, together with some details of the operating results of the unit as finally assembled. Developments in other directions in this same field have not, up to the present, pointed out an economic future for the process, therefore our record here is largely a report of development progress. Whether some particularly favorable location will be found at some future time for a commercial installation cannot as yet be fore-told. The project is now at a standstill. The peculiar tools of the electrometallurgist should be of great interest to the zinc smelter. The low thermal efficiency of the zinc retort, its comparatively small-scale unit and its intermittent cycle as it stood in 1925, should make this art a particularly fertile field for the electric fur-nace. Yet in spite of years of work recorded in volumes of literature, and an expenditure of large sums of money, there is not a single electrothermic zinc smelter operating anywhere in the world. In this industry the electric furnace plays only a secondary part today.

Jan 1, 1936

By B. R. Palmer, G. Gutierrez B., M. C. Fuerstenau

Flotation responses of chrysocolla and rhodonite are correlated with electrophoretic mobility and infrared spectroscopy measurements. Flotation is effected in the pH ranges in which hydrolysis of the metal ions comprising the mineral occurs. The roles of mineral solubility and precipitate formation are suggested.

Jan 1, 1976