Search Documents

By E. A. Stevens

IT has been ascertained in recent years that certain rocktypes, geological formations and structural conditions may be used as fairly reliable guides, when prospecting in recognized mineral belts or mining districts, with a reasonable certainty of discovering "pay-ore;" and that such is considered as a practically established conclusion may be inferred from a perusal of the recent reports of the U. S. Geological Survey and the literature of the several scientific societies discussing minim, geology, and kindred subjects. Cripple Creek is no exception to this conclusion, and the rock-type or association, rather than the structural condition, is the most infallible guide.† These guides consist of four, possibly five, dike-rocks, three of which are extremely basic, while the fourth is an acid rock of an entirely dissimilar character. The basic rocks are nepheline-basalt, limburgite, feldspar-basalt and tephrite. There are grounds, however, for believing that the two latter are subdivisions of one type, and therefore will be described under one head. The acid rock is quartz-porphyry. Nepheline-basalt is-a rock encountered in but few localities elsewhere on this continent, and occurs in narrow dikes cutting various formations. When typical‡ it is composed of

Jan 1, 1913

By D. W. Frommer

Processing nonmagnetic taconites by selective flocculation-desliming and flotation requires large volumes of water. If impounded without treatment, these off-process waters require excessively large areas for containment. To discharge the waste water into natural waterways would contribute to stream pollution and likely would not be permitted. In U.S. Bureau of Mines experiments conducted in the Twin Cities Metallurgy Research Center's 900-lb per hr pilot plant, approximately 85% of water requirements for the flotation-based treatment of a Michigan nonmagnetic taconite were met by reclaimed water. Water reclamation of the off-process streams from flotation was accomplished by controlled additions of lime, sodium carbonate, and a synthetic flocculant to reduce turbidities to 51000 ppm equivalent SiO*, while maintaining a Ca(II) content of =16 ppm in the finished effluent. Flotation concentrates of good quality were obtained using the reclaimed water. The cost of chemicals used in water reclamation was approximately equal to the savings in flotation reagents attributed to recycling of the water. Water quality is perhaps as important to flotation as are the reagents used. The character of water is extremely variable, depending on whether the source is a well, lake, or stream, upon the season and temperature, upon prior use, and upon the character of the watershed. All of these factors influence the water hardness and the quantity of other dissolved inorganic salts, turbidity, dissolved and suspended organic matter, dissolved gases, and pH. Frequently, the differences in water quality can measurably influence flotation selectivity, often to the point of spelling success or failure. Water hardness is particularly troublesome in flotation systems employing fatty acids, but other unrecognized constituents may also contribute to peculiarities in flotation behavior. Furthermore, a given water source may be entirely satisfactory in one flotation system, but entirely inappropriate in another. In recent years, society has given more attention than formerly to water use, even in areas where water is plentiful. However, both the demands of a growing population, with increased per capita needs, and also those of industry must be met. As a result, riparian rights must be negotiated with the appropriate government agency or agencies so that consumption of water is often allocated or otherwise controlled. Furthermore, the disposal of off-process industrial and domestic water is coming under the increasing scrutiny of these same governmental units. In these respects, the mineral industry is no exception, so that conservation, water reclamation, and reuse may be expected to assume increasing importance. In 1932, it was stated that, "water reclamation is generally more expensive than the economy in water and reagents resulting from its use. It is employed only if it is urgent to save water."' The economic aspects of this statement may still be true, but the unrestricted use of water is becoming less and less an option of the user. The purpose of this paper is to discuss an investigation conducted by the U.S. Bureau of Mines (USBM), in which water reclamation and treatment were undertaken to develop procedures for, and to assess the effects of, water reuse on the flotation treatment of nonmagnetic taconites. This investigation is a logical extension of previous work described by the author and associates at the Twin Cities Metallurgy Research Center employing selective flocculation-desliming and anionic flotation of silica from low-grade, nonmagnetic iron ores2,8 The requirements for the selective flocculation-de-sliming and the anionic flotation of silica processes determined the direction of the investigation. Previous studies had indicated that pH levels of about 11.0 and 11.8 were required for selective flocculation and flota-tlon, respectively. The calcium content of the water was believed to be of importance in both of these operations, and since Minneapolis tap water with a Ca(I1) content of about 16 ppm had been successfully used, an attempt was made to reclaim the process water at an equal level of dissolved calcium. Additionally, the objective was to nullify or effectively limit the effects of dispersants and fatty acid residuals from prior stages of processing. Last but not least, the system of water treatment had to have the capability of reducing turbidities to workable levels. With about half of the effluent being derived from the selective flocculation-desliming step and carrying about 25,000 ppm of highly dispersed, suspended fines, this last objective appeared formidable at the outset. Procedures for water reclamation were derived, in part, from well-known mineral dressing practices, from past observations and investigations, and from concepts contained in various pertinent publications on water treatment."c These procedures involved: 1) flocculation with lime and poly electrolyte-type flocculants, 2) lime-soda-ash softening, 3) chemical precipitation, and 4) mineral surface adsorption. Control was exercised at various stages of water reclamation by frequent measurements of Ca(11), pH, and turbidity.

Jan 1, 1971

NORTH AMERICA. CANADA Canadian Army Overseas. Ball, H. D. Bridges. C. Butterill, H. J. If. Ladner, F. E. Lane, H. C. Alillar, W. A. ALBERTA Calgary.-Chonette, W. C. Clark, L. At. Corbett, C. S. de Hart, J. B. Dingman, C. W. Fath. A. E. Fulton. J. If. Cray, J. G. Johnson. R. V. McCutchin, J. A. *Slipper, S. E. Vin Buckirk H. A.

Jan 1, 1944

By Eugene F. Poncelet

This paper attempts to analyze the phenomena involved in the fracture of brittle solids by simple compression. Glass squares standing on edge, and compressed between two parallel steel jaws, developed jagged fractures, roughly parallel to the compression. Polarized light disclosed the presence of high local stress concentrations indicating poor contact all along the contact surfaces with the steel jaws. Teszar has shown that partial contact between the jaws and such a compressed solid causes tensile stresses in the free surfaces of the solid normal to the compression. Furthermore, Scoble has shown that in brittle solids fractures are caused by, and develop normally to, a sufficient tensile stress. It follows that such "partial-contact" cracks must be expected. With optically flat jaws and specimens, no "partial-contact" cracks developed. Instead, very smooth cracks vertical to the compression appeared 'upon release of the pressure. Investigation showed that the friction with the rigid steel opposed the return of the glass to its original width, after creeping on the steel as compression built up, thus setting up tensile stresses in the glass surfaces. It was not found possible to eliminate these "release" cracks. Compressed to destruction, such specimens flew to dust. A Microflash photograph taken during the explosive disintegration revealed: (I) oblique parallel fragmentation cracks, 30" off the direction of the compression; (2) transverse forking fragmentation cracks, normal to the former; (3) release cracks parallel to the compression; (4) a disintegration cloud. Given a distribution of submicroscopic cracks of random orientation throughout the glass, Griffith has shown the highest tensile stresses to be located at the tip of the cracks 30" off the direction of the compression. Although the preexistence of such cracks or flaws in unstressed glass is doubtful, they can be generated by the distorting forces set up by the compression itself. Atoms, in a structure held together by Morse-type forces or bonds, have under tension both a stable and an unstable state-of equilibrium. The difference in energy level between these two states is a function of the tension, and this difference must be borrowed from the thermal energy level of the bonds to reach the unstable state and result in a broken bond. As the fraction of the bonds having at any instant a sufficient thermal energy level is a known function of that level, it is possible to determine, in function of the prevailing tension, the fraction of the bonds that are broken. Upon breaking of the bond uniting two atoms at the tip of an advancing crack, the two atoms accelerate away from each other, causing in the solid propagation of a

Jan 1, 1944

By Robert McKay

THE practical study of corrosion requires consideration off its economic aspects. It must be based on sound scientific principles, but it should be borne in mind that probably the most important object of a corrosion test is to determine what metal in corrosion-resisting construction will produce the greatest operating profit. Thus the corrosion test must be directly connected with money values or it is not a practical corrosion test. This, perhaps unusual, connection between corrosion and economics is partially due to the fact that corrosion deals only with the time factor or duration of equipment, and it is almost the only test which deals with this feature. In these statements a departure is made from the academic definition of the word corrosion and it is done deliberately. The use of the term corrosion is unusual. It is as though we spoke of a tensile test as. a "breaking" test. We are not interested primarily in the break but in the strength of the metal. There is no English word which expresses our main interest in corrosion-testing, but let us have clearly in mind that we make corrosion tests to prevent corrosion. Our real interest is in this corrosion-prevention, not in the corrosion. Previous to 1922, it was common comment that "it is impossible to determine the course of corrosion by laboratory testing." This statement was true at that time in that the technique of laboratory testing for corrosion resistance was so vague that tests in the laboratory gave untrue results almost as often as true ones. This was so, even in the simple case of determining which one of two metals better resists a given solution. While this is no longer true the number of misleading "corrosion tests" still being ground out by laboratories is too large in the light of our present knowledge. There are two important features of corrosion testing whose neglect is a large contributing factor to misleading results: (1) The economic relations of the corrosion tests to other tests; (2) testing technique.

Jan 1, 1929

The work of the Committee on Industrial Preparedness* is well summed up in the following letter written by Thomas A. Edison, Chair-man of the Naval Consulting Board, after President Wilson and signed the army appropriation and army reorganization bills: "The Committee on Industrial Preparedness of the Naval Consulting Board, of which committee Howard E. Coffin is chairman, after a five months' campaign in many ways unique in vigor and vision has played a very definite part in the measures for the national defense which have just become law. It is responsible for having laid the foundation for a true industrial preparedness in this nation. "Five months ago the committee, wholly non-partisan in make-up, acting with the civil, mechanical, mining and electrical engineers and the chemists of the country, members of five great scientific bodies, began its work in' every nook and cranny of the land. The purpose was to prepare American industry efficiently to support the armed forces of America in the event of war. "The public, the business men and the legislators at Washington knew little regarding the demands on industry in connection with modern war. No department at Washington was charged with the duty of coordinating the needs of the army and navy with transportation, industry, and kindred functions. The purchasing, quartermaster's and ordnance departments of the army and navy were unable to buy military supplies except by competitive offering in the open market. No one had considered the need, and no legislative machinery was in existence, for preventing the presence of skilled workers on the fighting front when they would in time of war be needed in the factories, mills and mines of the country. Neither at Washington or elsewhere was there even a list of the industrial resources of the nation in such shape as could be used for practical purposes in case war should come. "The three things, then, that the committee headed by Mr. Coffin set out to do and that now have been brought about were as follows: First, to mobilize concretely the business men of America and their output against a day of need. This meant chiefly to discover in fullest detail just what equipment our manufacturers possessed that might be swung over to supply the army and navy swiftly and bountifully from the hour the colors were raised. In a few weeks this initial task, which has been a truly colossal one, will be at an end. A complete report of the equipment of practically every concern of substantial size in the country is now in the hands of the - committee. Directly in charge of the great inventory has been W. S. Gifford, Supervising Director of the Committee. The second step was to procure legislation making possible the placing by the war and navy departments of annual orders for munitions in small quantities to American manufacturers now not producing such things, so that quietly, efficiently and thoroughly they could learn in time of peace how to supply the government in time of war. The new laws make all this possible. It should be said here that this practice will bring about a geographical diffusion of munition plants all over our country, instead of affording us only a few such concerns for the most part near the exposed seaboards, as at present. It is obvious that this system will also throttle all talk of a munitions trust.

Jan 10, 1916

As bizarre an example of competitive salesmanship to be imagined took place last June in Western Australia. A half dozen world renowned mining groups received a Japanese iron and steel investigatory mission. Geologists, engineers and businessmen, all specialists in iron ore, representing elements of the Japanese government and steelmakers, politely grilled each iron ore group for technical information and plans for property development. At stake were sales contracts with Japan for many millions of tons of iron ore. Since approximately two dozen visitors were involved, it was necessary to divide them into four groups for dispensing information, transportation and accommodations at the remote exploration camps. In a continent noted for its wide open spaces, the hinterland of Western Australia is spectacularly lacking in settlements. The state has better than one third of Australian land and statistically 0.8 persons per sq mile. In reality, however, over 400,000 of the 800,000 population reside in Perth. Under such circumstances, properly receiving and feting these important visitors would seem to be difficult but the competing exploration groups vied ingeniously to outdo each other in hospitality.

Jan 10, 1964

By Henry Howe

§1. FOUR ASPECTS OF FLOW in the plastic deformation of steel by overstrain, such as punching, wire-drawing, tensile rupture, etc., are: (1) The inter-granular, i.e., the relative movements of the several grains, each as a whole; (2) the intra-granular, i.e., the relative movements of the masses of ferrite or cementite and pearlite within those grains; (3) the intra-pearlitic, i.e., the relative movements of the pearlitic ferrite and cementite; and (4) the crystal unit slipping, i.e., the travel of the minute units past each other, along the slipping planes, giving rise to the slip bands of Ewing and Rosenhain. It may be objected justly that (2), (3), and (4) are in a sense "intra-granular," and that (4) is in a sense "intra-pearlitic." Hence clearness may be gained at times by calling these "Movements of the 2d, 3d, and 4th orders" respectively.

Jan 4, 1914

By Che-Yu Li, J. L. Gregg, W. F. Brehm

Oriented, oxygen-doped niobium bicrystals were tested in liquid lithium. The grain boundaries were attacked preferentially. The depth of the penetrated zone varies as (time)2. The penetration was aniso-tropic, had a high activation energy, and increased with the increased oxygen doping level. A possible model was proposed to account for the experimental observations. 1 HE grain boundary penetration of a metallic system by liquid metal has been studied by several investigators. Their results are summarized by Bishop.' Most of these works show that the penetration by liquid metal corresponds to the phenomenon of liquid metal wetting. In the case of a grain boundary, wetting will occur when twice the solid-liquid interfacial tension is smaller than the grain boundary tension resulting in the replacement of the grain boundary by two new solid-liquid interfaces. Other possibilities exist; for example, the atoms of the liquid metal may diffuse into the grain boundary region due to chemical potential gradient. The gradient can be produced by impurity segregation or simply be due to the increase in solubility in the grain boundary region. The penetrated grain boundary in these cases may remain solid at the test temperature. The Nb-Li system has been of considerable interest because of its possible technological applications. For fundamental interest it provides a possibility of studying the grain boundary penetration process which is not controlled by the wetting mechanism. The pure niobium is not attacked by the liquid lithium, but if niobium containing more than 300 to 500 ppm oxygen by weight is exposed to liquid lithium, corrosion occurs at the solid-liquid interface and preferentially at grain boundaries. Previous investigators2-' have proposed that this preferential corrosion at grain boundaries is caused by oxygen segregation there, with subsequent inward diffusion of lithium to form a Li-Nb-0 compound. These investigators also found that the corrosion could be retarded by adding 1 pct Zr to the niobium to precipitate the oxygen as ZrO2 upon proper heat treatment. However, there are no quantitative data on the kinetics of the grain boundary penetration process to test the validity of the proposed corrosion mechanism. In this work an investigation of this penetration process in oriented bicrystals was made as a function of the oxygen doping level in the bulk niobium and the grain boundary orientation. A possible model for the penetration process based on the experimental results was proposed. EXPERIMENTS Oriented niobium bicrystals were grown by arc-zone melting oriented single-crystal seeds.7 These bicrystals contained simple tilt boundary. The [001] directions in the two grains were tilted about a common [110]. The bicrystals were 31/2 in. long and 5 by 4 in. in cross section with the straight, symmetric, planar grain boundary longitudinally bisecting the crystal rod. The bicrystals were doped with oxygen by anodically depositing a layer of Nb2O on the surface in a 70 pct HNO solution at 100 v, using a stainless-steel cathode. The specimens were homogenized by annealing in evacuated quartz tubes at 127 5°C. Oxygen content of the niobium was measured from microhardness values, after DiStefano and Litmman.' Supplementary checks were made with vacuum-fusion analysis.7 Individual test specimens cut from the doped bi-crystal rods, about by by % in. in size, were tested inside double jacket sealed capsules. The inner jacket was niobium, the outer was stainless steel. The niobium inner jacket eliminated the problem of dissimilar-metal mass transfer.' The lithium (99.8 pct pure, obtained from Lithium Corp. of America) was handled only in a purified argon atmosphere in a Blickman stainless-steel glove box. After introduction of lithium, the capsules were sealed by welding. Further detailed experimental procedures are given in Ref. 7. The capsules were heat-treated in vertical Marshall resistance furnaces. Temperatures were controlled to When heating above 1100°C, it was necessary to seal the furnace work tube and flow argon through to prevent failure of the stainless-steel outer jacket of the capsule. Tests were made on 6" 2", 16" 2, and 33" i2" bicrystals at oxygen levels up to 2600 ppm by weight in the 6' and 16" crystals and with 1300 ppm oxygen in the 33' crystals. The oxygen levels were controlled to 100 ppm. Most of the quantitative data were obtained from 16" bicrystals between 800" and 1050°C. The capsules were quenched into water after the test and cut open with a water-cooled abrasive wheel. The capsules were then submerged in water, which dissolved the lithium and freed the specimen. Measurement of the depth of the penetrated zone in the grain boundary was done either on metallographically prepared surfaces or directly on the grain boundary plane after the specimen was fractured in tension in the grain boundary plane. The depth of penetration measured by both methods agreed well. Further details describing these techniques have been reported elsewhere.'p7

Jan 1, 1969

By Robert A. Brusca

OUTLINE Mineral Poor, but great primary inputs Net importer of most primary inputs • Copper • Zinc • Aluminum • Oil Problems for Japan • Supply Disruption • Currency Swings Remedies • Yen pricing of primary products • Long term contracts • Ownership of primary commodity producers Current Approach No Text Available

Jan 1, 1990

By Webster, Wm. Reuben

THE greatly enlarged demand for small sizes of seamless copper tube which has recently occurred, due particularly to the rapid growth of the electric household-refrigerator industry, has emphasized the superiority of phosphorized to tough pitch copper for the purpose of producing this commodity. In the manufacture of this material exceedingly heavy reductions by cold drawing are employed, customary practice involving as much as 90 per cent. reduction of cross-sectional area in four runs without intermediate annealing. Although this superiority has long been recognized by tube makers, no quantitative expression of it has heretofore been published. It is believed that the data herewith presented mill serve this purpose. Recent investigators are not in agreement as to the relative mechanical properties of copper containing small amounts of oxygen as compared with copper containing sufficient oxygen to produce that condition known as tough pitch. Hanson, Marryat and Ford1 found that "oxygen has a relatively small effect on the properties of copper." Johnson, on the contrary, states "it cannot be denied that it (tough pitch copper) is inferior to deoxidized copper . . . where severe mechanical manipulation is concerned." These authorities in the reports of their investigations, as might be expected from their conclusions, do not present data of a character requisite to a conclusive determination of the question.

Jan 1, 1927

By Orson Shepard

THE leaching method that was first widely used with the cyanide process consisted of percolation leaching of crushed ore in vats or leaching tanks. It was frequently necessary to separate the sand for cyanide treatment and discard the slimes, because only granular material allows the necessary amount of solution to percolate through it in a reasonable time. Later a slime process consisting of agitation followed by thick-ening and filtration was developed, and is extensively used to the pres-ent day. Even though the agitation-leaching slime process is considered satis-factory, the cost of plant and of operation are both greater than for a percolation-leaching plant of equal capacity. This situation has been recognized in the hydrometallurgical treatment of copper-bearing slimes; and a considerable amount of j work has been done at the Southwest Experiment Station of the U. S. Bureau of Mines in an effort to develop a percolation method of treating slimes. Experimental work on the copper-leaching problem was started by H. E. Keyes1, and later tests were made by J. D. Sullivan and A. P. Towne2. The Bureau of Mines work resulted in the development of a process by which slimes were moisture-agglomerated with sand and crushed ore, to form a permeable mass through which solution could be trickled without breaking clown the glomerules. The agglomeration trickle-leaching method was devel-oped on a small scale and finally tried out in a 12-ton vat. Successful results were obtained as long is the leach solution was added slowly, so that the agglomerated charge was never flooded. If the leach solu-tion flooded the charge, the glomerules broke down and, the charge became impervious. There are two important difficulties in the application of the agglom-eration trickle-leaching-method to the cyanide process for gold and silver ores:

Jan 1, 1937

By G. St. J. Perrott

One of the important hazards in coal mining is the danger of ignition of explosive mixtures of methane and air or coal dust and air, or both, by the explosives used in blasting the coal. It has long been recognized that certain explosives are more dangerous than others in this respect. ' In America and abroad, government testing stations have been established for officially passing on the suitability of explosives for use in coal mines. In this country the Federal government is given no power to enforce the use of the approved explosives but merely publishes from time to time, through the Bureau of Mines, those explosives which have passed the tests necessary to place them on the list for use in coal mines. In spite of this lack of police power, the increase in the use of permissible .explosives since the promulgation of the fist list in 1909 has been rapid. In 1912, only 8 per cent. of the explosives used in coal mines were permissible; in 1925, this figure had increased to 25 per cent. While the past record of permissible explosives has been most gratifying, it is very desirable that we pave the way for further improvement in explosives and blasting methods by learning more about the mechanism of ignition of gas and coal dust by explosives. To this end a considerable amount of investigative work already has been carried out and a large amount yet remains to be done. It is the purpose of this paper to discuss briefly the effect of the characteristics of explosives and method of loading in the borehole on the liability of a blown-out shot to ignite explosive mixtures of gas or dust. For an account of the methods by which an explosive is tested for permissibility for use in coal mines, the reader is referred to Schedule 17-A of the U. S. Bureau of Mines. Safety Factor in Using Explosives The factors that affect the liability of an explosive to ignite gas or dust are already known in a qualitative way but quantitative data are

Jan 1, 1927

By A. J. W. Schwandt

Magmont is a venture jointly owned by Cominco American Incorporated of Spokane, Washington and Dresser Minerals, Division of Dresser Industries, Houston, Texas. Cominco American assumed direction of the operation in 1961 and completed exploration, preproduction planning and development, and is now the operating partner managing the operations. The plant has a rated capacity of 4200 tpd and produces in excess of 60,000 tons of lead per year. [ ]

Jan 1, 1970

By Bruce N. McIver, Leo Casagrande

Similarities are noted in the practices and problems of constructing dams to impound mine tailings, fly ash, and chemical wastes. The comparison of a typical tailings dam with a conventional water-retaining earth dam shows that the former is inherently less stable and can be susceptible to cracking, liquefaction, erosion, and frost action, as illustrated by examples. Several methods are presented for building safe tailings dams using either the coarse fraction of the tailings or local soils, the important factor in each method being proper compaction of the material. The safety of existing tailings dams can be improved by flattening the overall slope, preferably by adding berms, or by decreasing the height. Where neither remedy is possible, the installation of electro-osmotic tie-backs is suggested. Dumps of mine spoil can be stabilized economically by compacting the material in layers along the toe to form a dam.

Jan 1, 1971

By J. W. Mills

In 1956 the discovery of nickel on Jumbo Mountain, Snohomish County, Washington, focused attention on this part of the Cascade Range, far more renowned for its timber than for its mineral resources. Hand specimens assaying as high as 13 pct Ni encouraged Discovery Mines Inc. of Mount Vernon, Wash., to stake 12 claims in Township 31 North, Range 9 East of the Willamette Meridian. The property was leased to Climax Molybdenum Co. in January 1957. Trenching, sampling, and geologic studies were carried out during the late summer of 1957 when most of the snow had disappeared. Although the deposits are only about four miles south of the logging town of Darrington and about two miles. as the crow flies, southeast of the end of a good gravel road from that town, all camp supplies and equipment were air-dropped, owing to the extremely rugged nature of the terrain. GEOLOGY The rocks of Jumbo Mountain comprise a series of folded Tertiary sediments forming a belt one half to three quarters of a mile wide, trending northwest about parallel to the strike of the beds. This belt is sandwiched between two extensive in-trusives—gabbro on the northeast and quartz dio-rite on the southwest—and has been intruded by dikes of fresh and serpentinized dunite. Shear zones follow many of the dunite-sedimentary rock contacts, and in these the nickel mineralization is concentrated. A few transverse faults offset the sediments and ultrabasics. Sedimentary Rocks: Two kinds of quartzite make up the greater part of the sedimentary section. One is dark purplish gray, very fine-grained, and thin-bedded; the other is light gray to white, medium-grained, and well-bedded. Locally the light-colored quart lites contain grit and conglomerate horizons, rich in pebbles of white chert and very fine-grained quartzite. Intercalations of dark argillites near the summit of the mountain give many of the cliffs a striking banded appearance. Dark gray to black, aphanitic, thin-bedded argillites occur throughout the entire sedimentary belt. Beds vary from a few inches to a few tens of feet thick and some, near the summit, contain numerous fossile (willow?) leaves. Only the thicker beds were mapped. The sediments are quite fresh on the northeastern side of the belt and become more metamorphosed (hornfelsed) toward the southwestern side. Brown biotite is present in the metasediments in increasing amounts as the quartz diorite is approached. Near the intrusion, porphyroblasts of plagioclase, up to 1 in. across, testify to the soaking of sedimentary rocks by solutions emanating from the quartz diorite. Most of the sediments mapped lie along the southwestern limb of an anticline, the axis of which follows the crest of the mountain and plunges at a low angle to the northwest.

Jan 1, 1961

S. LE FEVRE, Forest Glen, N. Y. (communication to the Secretary*).¬F. L. Nason thinks I could not have studied Mr. Witherbee's paper and doubts the arithmetic used, but in his discussion arrives at practically the same conclusion. He says 10 ft. thickness of ore over a square mile should give 27,878,400 tons, allowing 10 cu. ft. per ton of ore. This is correct, but if he reads carefully he will see that this depth of ore was figured as covering one-tenth of the surface, which reduces the figures to those used by Mr. Nason. I did not say, however, that there were 2,300,000,000 tons of ore in New Jersey, but that applying the same method of computation as used by Mr. Nason, to the area of the iron ore-bearing gneisses in New Jersey, we would get a total of 2,300,000,000. I did say, "In this area are located 366 magnetite mines that have been worked more or less. These lenses may easily be capable of producing (on an average) 1,000,000 tons each, and there are probably double the number listed not opened up." Thus my estimate for New Jersey, as far as any was made, would be: Probable ore 366,000,000 Possible ore in addition 732,000,000 1,098,000,000 Mr. Nason's final conclusion of his personal estimate was one-half of what he erroneously read to be the estimate given in the paper, or half of 2,300,000,000, which equals 1,150,000,000. So the two estimates seem to differ less than 5 per cent., and we have the two sister States of New York and New Jersey on an equal footing of productive possibilities in magnetic ore.

Jan 6, 1917

By F. R. Conley, D. A. Shock

Solution Mining or In Situ Mining has received increasing attention in the past few years because the method offers many attractive possibilities in improving the environmental impact of mining as well as making feasible the extraction of deeper, low value mineral reserves. This paper will present a brief discussion of the state-of- the-art in total solution, slurry removal and leach mining. As a specific example of utilizing the method, the uranium deposits of South Texas are a type of deposit which have been considered as being amenable to in situ leach mining. The parameters required to ascertain the amenability of such a deposit for in situ leaching will be presented. The hydrological factors which influence the production of the soluble uranium solutions and their displacement will be discussed. Mathematical models for various well configurations have been made and graphic representation will be presented to illustrate various production methods and the resultant hydrological consequences.

Jan 1, 1974

In an address delivered at Atlantic City, N. T., Dec. 5, 1918, M. L. Requa, General Director, Oil Division of the United States Fuel Administration, said: We face a new era with all its uncertainties. We have arrived at the period of reconstruction and are face to face with the problems concerning which we have so often speculated during the past four years. In all this reconstruction work the United States must bear an important part. We are looked upon to lead the way, to blaze the trail and our actions will have a profound influence upon the rest of the world. If we are to succeed, even in part, we must not be ashamed to practise economy; we must not despise the clay of small things; the little savings; we must have the closest cooperation between Government and industry. Just as truly do we need civic awakening. All that we have ever fought for, the liberty of the world, is comprehended in the ballot; and yet how lightly we have held this great privilege! We need, if we are to reap in full the benefits of the past 18 mo., an awakened civic consciousness; a jealous guarding of government; a resolution that we will, each and all, perform to the full the duties imposed upon us by Democracy; that we will perform more completely the obligations resting upon us as citizens. During the war, industry, through sane cooperation and intelligent effort, has accomplished results possible of attainment in no other way. Government and industry have worked hand in hand and pointed the way o to future activities which, if realized, can but be most highly beneficial to all. If Government and industry are to fulfill their respective duties satisfactorily, it is obvious that there should be complete mutual confidence. Industry must not attempt to "put something over"-and Government must treat with industry upon the high plane that has characterized the public utterances of the President during the war. The individual who cannot conform to these high ideals should have no place in industry, and equally no place in Government. If the dignified and broad princi-

Jan 2, 1919

Jan 1, 1947