Search Documents

By L. V. Pirela, S. M. Farouq Ali

Some interest has been expressed recently in the application of solvents in conjunction with a thermal drive, such as a steamflood. At least one field project of this type has been reported. This paper makes the first attempt to provide some of the basic information necessary for choosing a solvent for such an application. Results of displacements conducted at elevated temperatures are also discussed. This paper shows that, in the case of alcohol-hydrocarbon-water or brine ternary systems, the system miscibility may increase, decrease, or both increase and decrease within the same system when the temperature increases. The distribution coefficient was consistently found to increase in favor of the oleic phase with an increase in temperature, which is advantageous from the standpoint of oil recovery. Results of solvent displacements in a sandstone core showed that even a relatively small temperature effect in the favorable direction (increase in miscibility and distribution coefficient) can lead to a 50 percent increase in oil recovery. On the other hand, if the system miscibility decreases with the temperature, even though the distribution coefficient increases, the oil recovery at the higher temperature may not increase. INTRODUCTION Miscible displacement has been the subject of many investigations. Miscible-phase solvent flooding, employing solvents such as alcohols that are miscible with both oil and water, has received considerable attention. Investigations conducted by Gatlin and Slobod,l Taber, Kamath and Reed,2 Holm and Csaszar,3 and Farouq Ali and Stah14 have helped in understanding the mechanism of solvent flooding. While the use of alcohols and similar solvents as oil recovery agents is economically unattractive, these solvents nevertheless provide a means of understanding the mechanistic aspects of important miscible-phase oil recovery processes such as the Maraflood process (discussed by Gogarty5). As shown by Taber et a1.,2 the phase behavior of a solvent-oil-water system is of .utmost importance in determining the efficiency of the oil displacement. This paper makes the first attempt to obtain the ternary phase behavior data for nine alcohol-hydrocarbon-water/brine systems at elevated temperatures. Results of core tests at elevated temperatures are also presented which corroborate the effect of temperature on oil recovery, as judged on the basis of phase-behavior data. The use of solvents at elevated temperatures has been suggested earlier by Farouq Ali.6 At least one field test of this type has been reportedO7 With the widespread use of thermal recovery techniques, it is possible in some situations (especially in steamflooding) that the use of a suitable solvent in conjunction with the heat carrier may be economically feasible. This paper attempts to provide some of the basic information needed for judging such feasibility. LOCATION OF THE PLAIT POINT The phase behavior of a typical ternary system consisting of a solvent, hydrocarbon and brine (or water) can be represented by a triangular diagram such as the one shown in Fig. 1 (for temperature TI). Point Pon the binodal curve represents the plait point, being the limit of tie lines such as Y1 Y2 The compositions of the coexisting oleic and aqueous phases are given by points Y2 and Y1, respectively, for any mixture composition along Y1Y2. The characteristics of ternary diagrams have been discussed by Findlay8 and others. Taber et aL3 have shown that the position of the plait point in a particular ternary system plays the decisive role in determining whether or not theoleic phase would be displaced in a continuous manner during an alcohol displacement. The area above the binodal curve also is important, since it represents

Jan 1, 1969

By Warren L. Howes

This paper deals primarily with an investigation of ball-mill liners that was conducted by the writer over a period of six years at the Mammoth mill in Arizona. The investigation covered a wide variety of designs of liners in both primary and secondary mills. The comparative results are presented herein as evidence of the extent to which design influenced liner life and mill performance. Flowsheet The feed to the Mammoth mill was a complex, oxidized, gold-silver-lead-molybde-num-vanadium ore with rhyolite, andesite and granite as gangue. Although the ore varied between stopes, the long-term average in character remained substantially the same. Capacity was 560 tons per day.† Fig. I shows an abbreviated flowsheet of the grinding section of the mill. Primary Ball Mill A 3-ft. Symons shorthead crusher in open circuit crushed to 1/4-in. maximum one-way dimension the feed to the 5 by Io-ft. Marcy open-end ball mill. The mill rotated at 80 per cent of critical speed and was charged with 4-in. forged steel balls. Cast balls were used for a few months at a slight reduction in ball cost, but breakage of the large balls reduced the ball size and grinding capacity to a point where the over-all costs suffered out of proportion to the saving in cost of balls. For metallurgical reasons, the finished product of the mill was maintained at minus 8-mesh. This coarse product, plus the very abrasive ore and the absence of fines in the feed, caused abnormally rapid wear of the mill liners. The resultant high operating cost led to the most extensive phase of the investigation. In order to clarify the difference in design of the various types of liners used, Fig. a shows the profiles with the arrangement in which grinding balls of maximum size would lie on the face of the liners. The results with each type of shell liner in the primary mill are shown in Table I. Since most of the testing was done with

Jan 1, 1943

By T. L. Joseph

Blast furnaces are most efficient thermally when the CO2 in the top gas is highest. Oxygen introduced in the air blast is converted to CO in the combustion zones. The extent to which CO, generated in front of the tuyeres, is converted later to CO2 depends upon the ratio of ore to coke in the charge and the degree to which CO2, formed by reduction of iron oxides with CO, reverts to CO by the secondary reaction C + CO2 = 2CO. About 300 to 400 lb. of carbon' per ton of pig iron is normally involved in the solution-loss reaction or direct reduction of FeO with carbon, which produces the same over-all results; that is, lower CO2 in the top gas. Rich2 has recently reported a reduction in fuel consumption at slower rates of blowing on two furnaces in spite of higher heat losses per ton of iron. Lower fuel consumption at slow operating rates was due to more complete reduction of the ore that resulted in higher CO2 in the top gas and consequently more efficient use of carbon. Kinney3 has reported substantial savings in fuel as a result of crushing and sizing the ore charge. Improvements in practice brought about by sintering magnetite concentrates, flue dust and fine ores have been due to the establishment of conditions favoring more complete reduction of the ore in the upper part of the furnace. The extent to which oxides and fluctuations in composition in pig iron affect the quality of steel and finished product needs further study. There is evidence that more thorough preheating and reduction of the ore in the upper part of the furnace tend to give a better quality of iron. Bogatzkii4 found from laboratory work that the amount of oxygen entering electrolytic iron, melted under various slags, was directly proportional to the concentration of free FeO in the slag and inversely proportional to the basicity of the slag. Herty and Gaines5 concluded that the silicate content of open-hearth steel before deoxidation is related to the concentration of silica in the pig-iron charge, indicating that most of the persistent inclusions are silica from the iron. They also found that

Jan 1, 1936

SAN FRANCISCO SECTION W. H. SHOCKLEY, Chairman, PRANK H. PROBERT, Vice-Chairman, T. A. RICHARD, Sec.-Treas., 420 Market St., San Francisco, Cal. C. C. BRAYTON, J. F. NEWSOM. The San Francisco Section met on September 11 to discuss the problem of Labor in its Relation to the Mining Engineer. Mr. W. H. Shockley was in the chair. T. A. Rickard opened the discussion under four heads: The recognition of the union, the rustling-card, the sliding scale of wages, and the' contract system. He expressed his belief that collective bargaining cannot be ignored, and insisted that the mining company represented a collective bargaining of its shareholders with the men. employed in its mine. He held that the contract system was often used unfairly, but that used fairly it was the best check on labor tyranny. The rustling-card he held to be right in principle, in so far as it gave the employer the choice of employees, but he believed that it was often used in an irritating way to black-list refractory laborers. The sliding scale of wages was easy to establish in prosperous times, but it would inevitably lead to trouble when conditions went against the miner. His conclusion was that the quarrels of labor and capital were due mainly to a lack of the sense of fair play and of social justice. Albert Burch agreed with most of the foregoing, and insisted that 90 per cent. of the men were inclined to be just, but that the 10 per cent: made all the trouble. He stated that he had introduced the rustling-card in the Coeur d'Alene in 1899, as a means for getting rid of agitators. E. L. Foucar considered that labor was irresponsible. He described his experience in Peru, where the authorities promptly stopped a strike of Italian miners by threatening prompt punishment for any display of violence. Morton Webber also gave a bit of his own experience, to show that the chief trouble is that the men do not think for themselves, and are therefore easily led by fomenters of trouble. F. H. Probert described his experiences in Germany and. also in Arizona, and insisted that too often the men were not given a fair hearing. E. T. Blake argued that a manager must get the workmen's point of view, in order to control them effectively. He believed that young men who started life doing manual labor were in a better position to understand their fellow workers. George J. Young suggested that the mine owners should encourage the good men to lead the unions, and not leave the direction of the unions to the noisy element.

Jan 12, 1917

Four generations ago, the Mount Morgan ore deposit sustained the hurly-burly of frantic development common to the finding of a rich discovery. In this case, it was gold discovered in gossan capping on one of the hills of the Dee Range. The bonanza ore, like the flush of youth, has been spent. Today, one recognizes in this operation the orderly manner of the senior citizen, keeping up with the times and husbanding resources. As mining towns go, Mt. Morgan has an enviable situation. The approach is from Rockhampton, Qld, a peaceful, affluent agricultural and cattle center near the sea. To reach the mine, one goes 22 miles, first across farming country, passing orange groves and occasional children on horseback. The ascent into the Dee Range is winding and rapid. In the winter, the hills are green and Bougainvillaea and flowering yellow bracken grow wild on the hillsides. Around a bend, the brown waste terraces of the mine come into view, rising above the surrounding country. The top of the mountain has been sawed off and a deep pit sunk into the core. A little further on, around a few more curves, the town of Mt. Morgan is seen nestling comfortably in the hollows, reaching up the slopes.

Jan 10, 1964

By Ronald R. MacDonald

There is an ongoing need for the abstracting and coding of new information in the energy and environmental studies field for addition to the BIRS system. There are approximately 3000 bibliographic entries coded into the BIRS system. The bibliographic retrieval system was designed to be run by the general data management System 2000. The information system with entries of coal research, land reclamation and other energy and environmental studies is up and on line. As more entries are coded they are loaded into the system.

Jan 1, 1977

By R. Kerby, T. R. lngraham

The rates of cadmiuln cementation from buffered solutions were studied on both the cylindrical and circular faces of a rotating zinc disk. The activation energies are equivalent on both surfaces, but the rate is more rapid on the cylindrical face. At higher temperatures and at pH values above 6.4, the rate of deposition increases because of an increase in the cathodic area of the deposit. The rate may also be increased by decreasing the thickness of the diffusion layer by rapid stirring. The presence of small amounts of copper, cadmium, lead, iron, or aluminum in the zinc does not affect the cementation rate, but when srnall amounts of copper, cobalt, and arsenic were present in the solution cadmium deposition ceased shortly after it started. Small amounts of copper in solution become cemented with the cadmium to form a coarse deposit of Cd3Cu. When zinc ores containing cadmium are processed for electrolysis, the cadmium appears with the zinc in the leach liquors. Because of the discharge potential of the cadmium ion and the hydrogen overvoltage on metallic cadmium, the cadmium ion must be removed prior to zinc electrolysis to prevent its codeposition. Cadmium is usually removed from acidic zinc sulfate solutions by cementation on zinc. When zinc sheets are used with the appropriate conditions of pH and temperature, a finely divided, high-purity cadmium powder is obtained; it floats to the surface with attached hydrogen bubbles and, after careful washing, may be processed directly to a marketable product.' The reaction on zinc sheets is relatively slow because of the limited amount of exposed cathodic area on the sheets. A much more rapid reaction is obtained when zinc powders are stirred into the solution, but this procedure does have a potential disadvantage: some unreacted zinc may be trapped in the cemented cadmium and thus lower its grade.1 The equilibrium constant at 25°C for the displacement of cadmium by zinc is of the order of lo", which indicates that at equilibrium the displacement would be essentially quantitative and no back reaction need be considered. This indication is not entirely true, however, because in the presence of oxygen any loose cadmium which is out of contact with metallic zinc tends to redissolve after cementation.' The overall effect is much the same as that to be expected if the equilibrium constant were much smaller. Previous experimental work on cementation reac- tions3 is in general agreement that the rates of cementation usually follow first-order kinetics. The metal on which cementation occurs is considered to consist of anodic areas from which metal dissolves and cathodic areas onto which the reactive metal is cemented. For the reaction to continue, the cemented deposit must remain open and porous for the removal of ions. Usually, the deposited metal influences the rate of cementation; when it blocks the pores in the deposit, the rate of cementation will be decreased. Alternatively, when the cemented metal grows as den-drites or as coarse powder the cathodic area is correspondingly increased and the rate of cementation increases,3 Thus, it is only during the initial stages of cementation, prior to the development of deposit effects, that the kinetic behavior of the reaction may be studied without ambiguity. In this paper, experiments will be described for cementation of cadmium from dilute solutions onto the surface of a rapidly spinning zinc cylinder. The effects of ionic concentration, disk rotation speed, temperature, and impurities will be described. APPARATUS AND PROCEDURE The apparatus used for the experiments was described in a previous paper.4 It consisted of a 2-liter vessel in which the contents were protected, against oxidation, by a stream of prepurified nitrogen. The vessel was immersed in a water bath which controlled

Jan 1, 1970

By W. B. Potter

There is probably no more interesting group of mineral fuels to be found in any country than that occurring within the limits of the new State of Colorado. The supplies are so abundant, and the occurrence and distribution are so favorable for easy development and transportation to the future manufacturing centres of the State, that they are destined to play a very important part in the material growth and prosperity of the region, the more so because of the rich and varied stores of ores awaiting metallurgical treatment, and the comparative scarcity of timber for fuel. From a purely scientific point, also, these lignitic coals form an interesting and important series. An examination of their geological occurrence and relations opens up new and important questions regarding the comparative value of various kinds of geological evidence, while a study of the character and composition of this class of fuels, which forms a connecting link, as it were, between the lignites and the true bituminous coals, may lead to a more thorough and accurate classification of mineral fuels. The analyses here presented are from samples, of not less than fifty pounds each, obtained by myself during the summer of 1875, and may be regarded as representing very fairly the average run of

By H. E. Williams

In view of the frequent occurrence of petroleum in other parts of the world, it seems odd that so large an area as is contained within the borders of Brazil should be without this product. This apparent deficiency may be due, however, to our ignorance of the regions in which it may exist. In some places, indications point to the probable existence of petroleum in ages gone by; and while the presence of petroleum pools may be problematic, in several regions conditions not unfavorable to their occurrence exist. Yet, Brazil has enormous oil resources in the rich oil-shales in different parts of the country. Many of these shales are very rich and only suitable processes for the extraction of the oil are lacking. At the present time, only a few small experimental plants are producing oil by distillation from these shales. These plants have been the subject of recent investigations by the Geological and Mineralogical Survey, a preliminary report of which is in the hands of the printer. The only regions where studies have not been made are the upper Amazon, the Acre, the Rio Negro, and the Peruvian frontier, which really seems to be the most promising field for explorations of any in the country. In the vast plateau region of the interior north of the 20th parallel of latitude, granites, gneiss, mica schists, and very old metamorphosed sedimentaries predominate. Later, sedimentaries occupy a minor position and, where found in the interior, represent a thin veneering resting on the older rocks. At several places near the coast they have a greater development and contain considerable beds of oil-shale and may, .in some cases, offer conditions favorable for the occurrence of oil. Such deposits are found in the Permian rocks of central and southern Maran-hao; in the Tertiary and Cretaceous beds along the coast of Alagsas Sergipe, Bahia, and perhaps farther south in Espirito Santo; and in the Parahyba embayment north of Cape Frio and in the interior Tertiary basin of eastern Sao Paulo.

Jan 1, 1921

By G. I. Madden, L. H. Van Vlack

WhEN basic refractories which contain peri-clase, MgO, are used in steel furnaces, they are altered by iron oxide to form magnesiowiistite, (Mg,Fe)O, and an iron-rich magnesioferrite, (Mg,Fe)Fe2O4. Silica, which is usually present, produces a silicate liquid that surrounds the solid phases. The individual crystalline grains of the above two solid phases grow at elevated temperatures. Previous papersL" showed that, if either periclase or magnesiowiistite is present as the only solid phase, its grain size increases in proportion to temperature and in proportion to the square root of time; the growth rate is reduced slightly if the amount of silicate liquid is increased. Similar results have been observed for iron-rich magnesioferrite.3 To determine the effect of the presence of two solid phases on the rate of grain growth, micro-structural studies have been made on samples containing both magnesiowustite and magnesioferrite. The experimental procedure was the same as that followed in the previous studies of this type.'12 Briefly, this included determination of compositions from the available phase relationships4 that would produce the two phases of interest at the firing temperature and using reagent-grade raw materials to prepare mixtures of these compositions. The mixtures were pressed into pellet-size samples and then fired at the desired time and temperature. The samples were water-quenched to preserve the microstructure present at the firing temperature. Standard reflected-light metallographic techniques were used for sample examination and sample analysis. Grain sizes were determined by measuring the mean diameter of a number of randomly selected grains in a two-dimensional microsection. A large cross section of the sample was covered to prevent biased data resulting from such effects as localized differences in the radius of curvature of the crystal grains. Examination indicates that grain growth is restricted when more than one solid phase is present. This is illustrated in Fig. 1 for: (a) magnesiowustite plus a silicate liquid; (b) magnesioferrite plus a silicate liquid; and (c) magnesiowiistite and magnesioferrite plus a silicate liquid. Fig. 2 plots the

Jan 1, 1964

By Edward H. Robie

NEVER before have the annual company reports in the mineral industry field exhibited the typo-graphical art so abundantly as does the current crop. Time was when most company reports made a drab appearance and dry reading, mostly confined to financial data and text that gave little information to the public or technical men. Now, the dollar statistics assume less importance. Considerable information is given on what is going on at the company's plants, new equipment being installed, new methods, properties under development, ore reserves and grades, and similar information of interest to professional men working in the field. We have one suggestion for further improvement: The names of the officers and directors of the company are always given, but only a few companies give the names of the principal operating officials. We think, in the case of a mine for example, that the name of the general manager, his assistant, the mine and mill superintendents, and any other top operating officials who have been largely responsible for the success of operations, are worthy of mention. The reports are now widely read and this recognition is due them. Conspicuous among the annual reports that we happen to have seen, in point of typographical attractiveness, are that of the Texas Co., celebrating its fiftieth anniversary with a gold-plated cover and gold printing inside; and that of Noranda Mines Ltd., with a red and black cover that would attract attention anywhere. Comment on economics, taxes, and labor give an excellent picture of what our industry is facing. Consider the following, from the report of the Union Oil Co. of California:

Jan 1, 1952

By T. lkeda, R. S. Montgomery. A. Hara

Actual test specimens used in the previous laboratory wear investigation,' were fully characterized and the data is given in Table 1. Most of the carbides tested could be placed into groups of similar mean grain size. When the wear rates of the members of these groups were plotted as functions of their hardnesses, a family of curves resulted; curves for groups containing data from larger grained composites were at lower wear rates at the same hardnesses. Most specimens tested showed only A-1 porosity (ASTM Standard designa-

Jan 1, 1971

By W. L. McMorris, A. H. Brisse

IN the last several years the coal industry has intensified its effort to solve the growing problem of cleaning and recovering fine mesh coals. On one hand there has been increasing civic pressure for cleaner streams, and on the other hand there has been increasing production of fine mesh coal, resulting directly from adoption of the modern mining methods so essential to the economy of the coal mining industry. Cleaning fine coal with the same precision possible with coarser coals is a difficult task, and for coals finer than 200 mesh it has been impractical. Furthermore, the inclusion of -200 mesh material in the final product markedly increases costs of dewatering and thermal drying, which are necessary steps if coal is to meet market requirements. Consequently these extreme fines have generally been wasted. As a result, problems have been created in many districts because there has not been enough area for adequate settling basins.

Jan 2, 1958

By H. J. Hager, P. H. Haskell

Fox the past 20 years Alabama has probably led all other coal-producing districts in the proportion of coal prepared by wet washing. All rail mines, with one exception, and a high percentage of truck mines now wash all coal under 3 or 4 in. Most of this coal has been cleaned by jigs, though within the past few years one or more wettable plants have been installed for cleaning some of the coal from practically all the major seams. These tables supplement either single or multicell jigs usually for one of the following purposes: (I) to wash the finer sizes of raw coal, (2) to rewash the finer sizes of washed coal after they leave the jigs, (3) to retreat jig middling products. The main purpose of this paper is to present cleaning data and operating factors involved in the preparation by tables of the finer sizes of raw coal. The specific information and data pertain to the Mary Lee seam of coal as extracted at three of the mines of the Alabama By-Products Corporation, which produces coal for both by-product coke-oven consumption and the general steam market. The Mary Lee seam has long been recognized by coal-preparation authorities as presenting a very difficult ash-reduction problem. Washing characteristics and physical structure of the seam vary widely. Its thickness ranges from 32 in. with no rock parting to l00 in. with from one to three partings. Over the entire field the bed contains bands of bone and rash. These are distributed throughout the seam cross section. A portion of this bone or bony coal occurs as definite bands 1 in. or more thick; however, some bone is interlocked as layers within the coal and consequently breaks into flakes when the coal is broken. This material is relatively high in ash and its specific gravity varies widely. It has been observed that in most cases in the washing of Mary Lee coal from 10 to 18 per cent of the raw coal is within ±0.10 specific gravity of the attempted point of separation. Therefore with the average wet jig, only with extreme difficulty can a low-ash product be obtained without loss of much marketable coal in the refuse. Without entering into the controversial question as to whether modern washing equipment can efficiently handle simultaneously all sizes up to a given maximum, suffice it to state that the comparatively old-type jigs in service at the Alabama By-Products Corporation's mines could not clean the fine sizes satisfactorily. Therefore, in 1931 that company installed six diagonal-deck tables at the Barney mine, which were installed as an addition to a complete plant cleaning all coal below minus 3 in. The primary washed product is shipped as steam coal and another portion may be prepared as washed nut for domestic trade. These tables are washing 9 tons per hour of raw coal sized to ¼ in. to 0. The washed table coal is mixed with the 3 to ¼ -in. jig product to constitute a 3 in. to o steam coal.

Jan 1, 1941

By Arthur W. Gray

The thermal analysis of a metal or an alloy is ordinarily made with the aid of heating and cooling curves in which transitions are indicated by the rapid changes in curvature that accompany changes in the rate of heat absorption or evolution. Analysis by the method that depends on the change in thermal expansivity is not customary, partly, at least, because of the difficulties involved in making the necessary measurements. However, under certain circumstances, the dilatometric method of analysis may possess advantages over the thermometric method that will justify the additional trouble required. The addition of 1 per cent. of zinc to an alloy has been found to produce upon the volume changes that take place during transition effects that suggest the possibility of using the dilatometric method of thermal analysis as a rather sensitive means of obtaining chemical information. Although the illustrations presented in this paper are drawn from data obtained during an investigation of dental amalgams, similar phenomena can doubtless be observed with other alloys. Some of the results found during an investigation made in 1917l have been confirmed by data on the thermal expansivity of amalgams published by Souder and Peters of the Bureau of Standards in reporting tests of dental materials.2 Although the Bureau of Standards made experiments for the purpose of discovering effects of including zinc as one of the constituents of a dental alloy—a matter much discussed in dental literature but without the presentation of reliable experimental evidencae to support the views of either side—the reports of the tests made by the Bureau give the impression that certain striking phenomena associated with the presence of zinc were not noticed. Among such phenomena arc those connceted with the conditions that determine whether or riot a specimen of amalgam becomes covered with droplets from which crystals develop.

Jan 1, 1921

By Charles Y. Clayton, Henry S. Burnholz, Francis B. Foley

This work was first undertaken for the U. S. Bureau of Mines, in 1919-20, by C. E. Julihn, superintendent of the station at Minneapolis. Learning of the interest, in this subject, of B. F. Tillson, of the New Jersey Zinc Co., Mr. Julihn and Mr. Foley went to Franklin, N. J., and discussed the matter with him. A conference in Chicago, in November, 1920, was attended by Dr. F. G. Cottrell, who was then Director of the Bureau of Mines, and representatives of the Bureau of Mines and of the hlissouri School of Mines and Metallurgy; at this time a cooperative plan of work was agreed upon by the Bureau of Mines and the Missouri School of Mines. In February, 1921, Mr. 'Tillson arranged a conference on this subject at the time of the annual meeting of the American Institute of Mining and Metallurgical Engineers, at which several technical papers were presented. In a paper, the Breakage and Heat Treatment of Hock Drill Stcels, he suggested a program that might be carried out in connection with the investigation of the problem. At this conference Mr. Manning, former Director of the Bureau of Mines, suggested the formation of an advisory committee to the Bureaus of Mines and of Standards for prosecution of this investigation. On Feb. 20, 1922, a secoud conference in New York, at the time of the annual meeting of the American Institute of mlining and Metallurgical Engineers, was attended by representatives of various technical societies. At this meeting, the report of Nov. 20, 1921, of the Chiefs of Divisions of Metallurgy of the Bureaus of Mines and of Standards, was discussed and it was agreed: 1. That the survey recommended by the two bureaus should be undertaken, which survey would have for its object the ascertaining of the present status of the practice of the heat treatment of drill steels, the extent to which the breakage occurs, etc.; and 2. That a report should be presented, of the findings of those who made the survey, to the Advisory Board to the Bureaus of Mines and of Standards. The Bureau of Standards assigned $4000 to the prosecution 01 a three-months' survey, which was carried out in April, May, and June, 1922, of about sixty mines

Jan 1, 1923

By John C. McDonald

This report is a continuation of an earlier one with a similar titlell to which the reader is referred for such details of procedure as do not appear here. A brief summary will be given of the objects and methods of the research at this time. It was pointed out in the previous paper that properties of magnesium alloys, as reported by different workers, often differ. This was thought to be due to differences in the preparation of the specimens tested. The ideal way to compare alloys would be to prepare each of them in so many ways that reasonable assurance would exist that the best properties of each alloy had been developed. The alloys would then be compared on the basis of these properties. The treatment actually given the alloys of these studies is necessarily a compromise with completeness. Nevertheless, enough treatments have been given so that a considerable degree of assurance exists that the properties obtained are representative of the alloy as such, and not merely of the manner in which it was worked and heat-treated. Procedure The alloys were cast in the form of cylindrical ingots, which were extruded into bar before being rolled. Some of the ingots were made in 2-in. diameter molds whereas all of the alloys of the previous paper were cast in 4.in. molds. For the larger ingots, the extruded bar was 2 by 0.140 in.; lor the 2-in. ingots, it was I by 0.100 in. Preliminary work indicated that strip rolled from both sizes of the bars would have substantially the same properties. The bar was rolled at some temperature in the range 400' to 800°F., for a total reduction of 50 per cent. The temperature and reduction per pass were so selected that no cold cracking occurred, but were such as to leave the metal in a semihard condition. The hot-rolled metal was annealed at several temperatures in the range 400' to 800°F.; it was also cold-rolled, and given solution and aging treatments. Two standard test bars corresponding to each treatment were pulled in tension, and the average was obtained. Twelve treatments, in all, were given each alloy. The properties of the annealed specimen having the highest percentage of elongation were selected to represent the alloy in the annealed condition. The properties of the cold-rolled specimen having the highest yield strength were selected to represent the alloy in the cold-rolled condition. These properties were then plotted against percentage composition by analysis. Smooth curves were drawn among the points, thus graphically averaging the results over the entire range studied. The percentage of elongation in the cold-rolled state was not plotted, since it was always low, and varied in an irregular manner with composition. Alloys Studied Magnesium-calcium Alloys.—Fig. I presents the results on the alloys of the rnag-

Jan 1, 1941

By G. C. Gardner

A new correlation of blast penetration in model and operating blast furnaces is presented which overcomes objections to prevzous correlations. It is shown that the tuyere diameter is only of small importance in determining the magnitude of the penetration. The data from operating furnaces correlate satisfactorily with the data from models whose cross section is a segment of a circle. A bubble-shaped gas space called a "raceway" normally exists in front of the nose of a blastfurnace tuyere. The periphery or "wall" of the raceway is well defined and is composed of densely packed charge particles. The blast. issuing as a jet from the tuyere, entrains gas from the raceway, in the usual manner of a jet, as it flows to the opposing wall. There it divides and flows back around the walls to be entrained once more. The blast must, of course, eventually leave the raceway and pass up through the charge column, but before it does it may, on the average, make several circuits of the kind described and in doing so it carries with it charge particles, which, because of their fast and circulating motion, suggested the name of "raceway". A fuller description of the raceway may be found elsewhere."' Here it is only necessary to mention, in addition, the measurement which characterizes its size. If an iron bar is pushed through the opened peepsight of a tuyere, .as far as it will go with ease, it will be stopped by the relatively impenetrable opposing raceway wall arid the distance that the bar has been pushed from the tuyere nose is called the "penetration". This measurement may be of practical importance and has; been the subject, with considerable success, of several attempts at correlation with other variables2-5 as stated in the next section. There is still, however, a serious objection to the most recent correlation,3 which is overcome by the correlation proposed in this paper. It will be shown that the objection is not trivial, in that the new correlation will attribute considerably different importance to the variables affecting the magnitude of the penetration. The data to be treated were made available by Wagstaff and are the same as those used in his correlation. They include measurements taken on small models, in which a cold air blast was used and no combustion occurred, and they also include data from operating blast furnaces at Wheeling and Fairless. The information from the blast furnaces will be shown to be in substantial agreement with those models whose plan views are segments of a circle and which are thus like segments of a blast furnace. First, Wagstaff's most recent correlation3 will be discussed and the objection will be given. Then the new correlation will be developed and its implications considered. CORRELATION OF J. B. WAGSTAFF Wagstaff's correlation is where and D — the penetration D,-the internal tuyere diameter V —the blast velocity in the tuyere

Jan 1, 1961

By C. R. Hayward

THE CHAIRMAN (ALBERT SAUVEUR, Boston, Mass.).-I am sure we are indebted to Prof: Hayward for his addition to our knowledge of the influence of sulphur on steel. As he has said in this paper, sulphur has had many defenders in recent years. It seems to me, however, that, while it may be old school to believe in the detrimental action of sulphur, it is not yet old school to believe in segregation; that while it may be that 0.1 per cent. of sulphur has no very great effect on the physical properties of steel, a ladle analysis of 0.1 per cent. of sulphur may readily result in 0.2 or 0.3 per cent. sulphur being present in the segregated portion of the ingot, and that, it seems to me, might be a rather serious matter. J. S. UNGER, Pittsburgh, Pa.-Prof. Hayward has presented the results of an investigation along a line to which I have devoted considerable time and attention, and I am particularly pleased to note that his results are in accord with my own and further tend to prove the fact that the old, established prejudice against sulphur is based more on belief than actual facts. I have felt for years that tooo much stress was placed on the harmful influence of certain elements in steel such as sulphur, phosphorus, copper, etc., but it has only been within recent years that efforts have been made to, establish the truth. Practically all the investigations made to date have proven that these elements within reasonable limits are harmless and, in fact, that for certain purposes the addition of these elements is beneficial. In referring to copper, J. E. Stead, Vice-President of the British Iron and Steel Institute, said at their last meeting: "Even today one comes across steel specifications in which copper is barred, which can only be regarded as ail indication of ignorance, if not stupidity, of those who prescribe the composition of steel, for it has been long ago proved that copper in steel, instead of being an evil, is quite harmless, and is sometimes distinctly beneficial." Sulphur owes its evil name to the early days of the manufacture of steel. Chemical analyses were crude, and failure due to either poor raw materials or metallurgical treatment were many. Sulphur being a comparatively easy element to determine with reasonable accuracy, particular attention was called to the amount of sulphur, and the failure was attributed to it, without giving any consideration to other causes. A pre-

Jan 4, 1917

By E. A. Lawrence

The experiences of Canex Placer Ltd. in establishing vegetation on a lead-zinc tailing pond are presented, hoping others with similar challenges will be benefited. History The tailing ponds are the result of 23 years of mining and milling operations, which ceased in August 1970. Roughly 7.9 million tons of lead-zinc ore were removed in that time. The ponds are located between Salmo River and B.C. Highway 3, about 8 miles north of Nelway near the Canada-U.S. border.

Jan 1, 1975