Search Documents

By M. Cohen, R. J. Teitel

There is considerable interest in beryllium because of its low density (1.84 g per cu cm), high modulus of elasticity (40 X 106 psi), high melting point (1280°C), and special nuclear characteristics. Moreover, it has fair resistance to corrosion and oxidation. However, the purest beryllium known to the authors is relatively brittle at room temperature, and cannot be fabricated readily. The search for improved properties leads naturally to investigations of beryllium alloys and the phase relationships upon which they are based. The present paper is concerned with the alloys of beryllium and iron, primarily from the standpoint of the equilibrium diagram. Iron was selected (1) because of its all-round importance in metallurgy, and (2) because the beryllium-iron system is known to be quite complex. The most recent diagram in the literature is that of Gaev and Sokolov,' and covers only the iron-rich end up to 16 wt pct beryllium. Beryllium markedly restricts the austenitic field, closing the gamma loop at about 0.4 wt pct (3 at. pct). On the other hand, beryllium is soluble in a-ferrite up to a maximum of 7.5 wt pct (34 at. pct) at the eutectic temperature of 1160"C. The eutectic composition lies at 10 wt pct beryllium (42 at. pct) and corresponds to a mixture of or and FeBez (called j3 in the present paper). The solid solubility of beryllium in the a phase decreases with decreasing temperature, and makes precipitation-hardening possible. These findings substantiate the earlier work of Oester-held,2 Wever and Mueller3 and Laissus.4 In addition to the FeBe2 (ß) mentioned above, Misch6 has reported on FeBes, and indicated evidence for another compound containing still more beryllium. A preliminary diagram by Gordon,5 not hitherto published, is given in Fig 1. Besides the phases previously named, there are shown a solid solution of extended range (e), a compound of limited solubility (t), and a high temperature phase (7). Beryllium is designated as 8. The t field contains the compound composition FeBea, and the f phase undoubtedly corresponds to the beryllium-rich compound found by Misch.6 The region around the { phase was proposed by R. J. Teitel based on Gordon's data. The details of the diagram are self-explanatory. It was the unusual complexity of this system that prompted the authors to undertake the present studies. By the same token, more emphasis was placed on the beryllium-rich than the iron-rich end of the diagram. Exprimental Details RAW MATERIALS The beryllium employed in this investigation was one of the purest grades available. Its chemical analysis after vacuum melting is given in Table 1. The metal assayed 99.4 wt pct beryllium. Vacuum melted electrolytic iron of purity shown in Table 1 was the source of iron.

Jan 1, 1950

By D. E. Musgrove

The question of alternating current vs direct current has become an important consideration to the mining industry. Rising production costs demand lower investment, which, in many instances, can be realized by the use of ac mining machines. Generally ac motors, control systems, and distribution and power conversion equipment can be installed for approximately 50 pct of the first cost of their dc equivalents. This basic saving has made ac mining a serious competitor for the traditional dc mining systems. With the increased use of ac voltages underground, there has developed the problem of conveniently converting distribution voltages to usable 480-v power. Power at low voltages should not be carried for comparatively long distances, and the transformation should be made at the point of use. Otherwise, serious voltage regulation problems and objectionable line losses will occur.

Jan 5, 1955

United Engineering Society ARTHUR S DWIGHT J VIPOND DAVIES J V N Dorm Engineering Societies Library Board SIDNEY H BALL ALEXANDER C HUMPHRFYS GEORGE C STONE JOHN H JANEWAY Engineering Foundation Board H M BOYLSTON J VIPOND DAVIES GALEN H CLEVENGER Society for Promotion of Engineering Education WILLIAM KELLY ALLEN H ROGERS

Jan 1, 1923

Jan 1, 1934

By Norman Pilling

The micrographic analysis of silicon steels is possible if a dilute solution of nitric acid and methyl alcohol in nitrobenzol is used. The action of this reagent differs from that of sodium picrate in that there is no persistent deep-seated staining and the solution is used cold. THE technical difficulties hampering the metallographic analysis of silicon steels are chiefly the result of the extreme corrodibility of these alloys. The addition of silicon to iron in increasing quantities, up to about 6 per cent., rapidly increases the susceptibility of the alloy to chemical attack, not only in acid solution, but in water. This renders the preparation of metallographic sections very difficult, because of a non-selective attack upon the finely polished surface by the water used as a lubricant in polishing. This water attack masks the true structural details revealed by suitable etching reagents. It is thus necessary to use alcohol as a polishing lubricant in the last stages of preparation and to avoid all etching reagents having an aqueous base. A specific reagent for the identification of iron carbide in ferrous alloys, and the one hitherto used almost exclusively by metallurgists, is an alkaline aqueous solution of sodium picrate, which stains this constituent selectively. Its application to silicon steels has not proved successful, as its distinctive selective action is more or less completely hidden by the general attack of the aqueous solvent on the silico-ferrite, greatly accentuated by the fact that this reagent must be used at its boiling temperature (105° C.). Thus, a powerful metallographic aid to the study of the higher silicon alloys, such as transformer steels, is lost. A new reagent has been developed for the purpose of overcoming this difficulty. It is with some hesitation that the list of etching reagents, already overburdened, is increased, but the properties of this new reagent are advantageous in several ways and a definite field for it may be found in the metallography of ferrous alloys.

Jan 1, 1924

By Elburt F. Osborn

The phrase "Clean Synthetic Fluid Fuels From Coal," implies that it is possible to obtain adequate and dependable supplies of fuel without sacrificing the quality of our air, water, and land. Because of the long lead times needed to develop technical feasibility, into commercial reality, however, vigorous efforts must be made now in order to do it. The available options for clean fuels include many exotic sources, like solar and geothermal power, fuel cells, and thermionic and thermoelectric systems. To solve the energy crisis, however, we have three basic energy criteria-abundance, reliability, and commercial availability by 1985. Only processes based on converting coal and oil shale to clean, synthetic fluid fuels can meet all three.

Jan 9, 1974

Roger A. Markle was sworn in as director of the US Bureau of Mines on September 27, 1978, ending a 20-month period during which the Bureau was without a leader. Some Bureau observers wondered out loud if this delay was a signal that Interior was slowly pulling the rug out from under the agency. When Markle was finally tapped for the director's position-coal industry executive to lead an agency that had been stripped of its fossil fuel R&D functions as well as its safety and health enforcement role--the speculation was fast and furious: One camp had it that Markle was brought in to phase out the Bureau; others said that Markle's directive was to revitalize the organization by charting a new Bureau course. In March, with the proposed Department of Natural Resources making headlines, ME went to Washington to interview Markle about his first six months as director and the goals he has set for the Bureau's future.

Jan 4, 1979

By S. E. Bronisz, R. E. Tate

s-plutonium samples possessing a strong growth texture have been produced by allowing them to transform under pressure from p to a. A fiber texture with [010] parallel to the pressure axis results. The textured samples are expected to be useful in determining the effects of crystallographic orientation on the physical properties of a plutonium, and initial results of measurements of resistivity and mechanical properties are described. THE crystal structure of a plutonium1 is mono-clinic, P21/m, and many of the metal's properties should reflect the crystallographic anisotropy. Unfortunately, it has not yet been possible to grow useful sizes of single crystals of a plutonium. Therefore, few of plutonium's orientation-sensitive properties have been determined as a function of crystallographic orientation. One way to gain information about at least some of the orientation-dependent properties is to study a highly textured sample. Such samples have been produced by cold rolling a plutonium,2 but they are necessarily very small in one dimension. We have now successfully used two other techniques to produce highly textured samples, not limited to small thicknesses. METHODS OF PRODUCING PREFERRED ORIENTATION The texture is produced by causing the plutonium to transform from ß to a while under pressure. It was observed by Gardner3 that applying a compres-sive load during the transformation resulted in the formation of columnar grains of a plutonium, and Cramer4 observed a similar structure in some diffusion couples rolled in the P phase. Neither of these workers, however, investigated the subject beyond these observations. The more flexible of the two methods developed is that of compressive loading. The technique is to enclose a sample of plutonium in a die assembly before applying the load. It is possible, of course, to dispense with the die and simply press the sample between two platens. In this case, however, the unrestrained sample deforms during the pressing, making it difficult to maintain the load and to control the final sample thickness. This compressive loading technique has been used on specimens ranging from 1/4 to 3 in. diameter, with height-to-diameter ratios ranging from 5 : l to 1:6. The procedure begins with loading the sample, a right cylinder of a plutonium, into the pressing die. Plastic deformation of the sample while it is being pressed is minimized by machining the sample so that its diameter is nearly the same as that of the die barrel. Then the loaded die assembly is placed in a vacuum pressing can that fits on a hydraulic press. After a vacuum is achieved the die assembly is heated to 180°C and equilibrated. The load is then applied and the specimen and die are allowed to cool to about 40° to 50°C before the pressure is removed. The resulting sample is composed of rod-shaped a -plutonium grains, the rod axes being parallel to the cylinder axis and the pressing direction. Photomicrographs of the oriented structure are shown in Fig. 1. Although most of the specimen is composed of grains whose rod axes are parallel to the cylinder axis, a thin, peripheral layer consists of rod-shaped grains whose rod axes are perpendicular to the cylinder axis. Presumably, the highly plastic nature of p plutonium leads to approximately hydrostatic conditions during the initial stages of the P — a transformation under pressure. At this time, the grains in the peripheral layer would have grown parallel to the local force direction. During the latter stages of the transformation, the accompanying volume contraction would have eliminated the radial forces, leaving only the axial force and resulting in the growth of the observed structure. The growth texture did not form without the application of pressure. Attempts were made to produce the texture by repeating the standard temperature cycle without

Jan 1, 1965

By Persifor Frazer

IT was my intention to have directed the attention of the members of the Institute to a complete series of rocks representing the older and middle formations represented in Pennsylvania, but time has been insufficient for the purpose, and I have been unable, in the first attempts to reduce the sections of those rocks, which I have brought with me to this meeting, to the requisite thinness necessary for exhibiting the peculiarities of their constituent minerals. The rocks represented here belong to the various horizons already mentioned, and include gneiss, ferruginous gneiss, chlorite slate, quartzites, and hydro-mica slates, limestones, dolomites, ferruginous conglomerates, quartz conglomerates, "Potomac marble" (nether member of the Mesozoic series), dolerites, and a syenite. The order in which these are named is, roughly, the order -of geographical position in a section line from southeast to northwest, commencing at the intersection of the Northern Central Railroad with the Maryland line, and ending a few miles from the town of York, and a short distance within the marginal outcrop of Mesozoic red sandstone. In such a geographical section all the rocks above mentioned would be encountered in the given order except syenite, about which a few words are to be said in a moment. (But this is far from representing the rocks in their geological sequence.) There is nothing of unusual interest to present to your notice in these slates and quartzites. The limestones were carefully searched under 450 diameters microscopic power, but they show no signs of organic remains. One section of a fine-grained Triassic sandstone contains a very beau¬tifully banded plate of quartz. But the objects of greatest interest at present are the specimens of trap. The more fine-grained and compact traps were collected from

Jan 1, 1875

By W. D. Roberts

INTERGRANULAR corrosion of metals and alloys has been extensively investigated and the current conclusions are summarized in the Symposium on Stress-Corrosion Cracking of Metals.' It appears, however, that the relative importance of the various factors involved in the mechanism is still obscure. Several recent, independent studies, in combination with available X ray data op preferred orientation, indicate that there may be a direct correlation between relative orientation of contiguous grains and susceptibility to intergranular corrosion. The object of the present note is to show the nature

Jan 1, 1951

By S. C. Sun, John A. L. Campbell

Objective of the ittvestigation was to determine the electrokinetic differences, if ally, of anthracite lithotypes and thus establish the feasibility of making a coqlstituent separation by froth flotation or other surface-dependent processes. The elec-trokinetic properties were determined by streaming potential methods. In addition, chemical and physical analyses of the lithotypes were made to establish nonsubjec-tive parameters for their diflerentiation. Electrokinetic results indicate a difference in the characteristics of the lithotypes. The isoelectric points of 4 anthracites and 12 lithotypes were obtained. It was suggested that the relative flotation rates of the lithotypes were pH dependent and that the maximum flotation rate of anthracite occurs in an acidic circuit. Although there has been an increased interest in the electrokinetic properties of coal,' research on the subject is still in an early stage of development."' To the authors' knowledge, no electrokinetic studies have been made on coal lithotypes, particularly anthracite litho-types. This paper presents the results of an investigation of the double layer properties displayed at the anthracite/water interface (whole coal and lithotypes) as determined by streaming potential methods. It is hoped that this investigation and related future investigations will provide correlations from which the surface properties of any coal can be predicted and then related to surface-dependent processes such as froth flotation and flocculation. Another aspect of this research, undertaken to determine the physical and chemical parameters necessary for anthracite lithotype differentiation, was previously published.? The number of parameters involved, lithologic, organic and inorganic, and the wide divergence of these parameters within an individual coal limits the practical utilization of the results; however, the result? are of value and of interest in guiding theoretical developments. Keeping the limitations in mind, the results are analyzed in terms of their application to froth flotation processes and are used to indicate the feasibility of making a lithotype separation by flotation. Experimental Procedure Prior to discussing the experimental work per se, it would be of value to establish an understanding of anthracite lithology. Anthracite Lithology: Coal seams display two different modes of variation, rank and type. A coal's position in the continuous series ranging from peats through anthracites determines its rank. The rank of the material under consideration is anthracite. The different bands of coal which constitute a coal seam are distinctly contrasted in regard to physical properties and chemical composition. These megascopic bands are the coal types and are termed lithotypes., A megascopic examination of 11 anthracites revealed three distinct, homogeneous, lithotypes. The classic description of bituminous coal lithotypes as proposed by Stope" was found to be quite adequate for recognizing the three lithotypes in anthracite, namely vitrain, durain, and fusain. The term vitrain describes the brilliant constituent of coal; durain describes dull coal; and fusain is the term applied to fossil charcoal. The anthracites studied were generally found to contain 60-80% vitrain, 10-30% durain, and 1-10% fusain. A complete description of the physical characteristics and chemical composition of the studied lithotypes can be found in a previous publication.' Sample Preparation: Nine of the anthracites used in the investigation were from Pennsylvania, one was from Russia, and one from Wales. Table 1 shows the various designations and sources of the employed anthracites. The letter V, D, or F added to the whole coal designation indicates respectively the vitrain, durain or fusain lithotype of that coal. The samples were carefully collected to avoid contamination. To insure against oxidation, the samples were obtained as fresh as possible and stored under nitrogen or water. Generally a representative sample of the seam and samples containing high concentrations of one or another of the petrographic constituents were secured for each coal. Pure lithotypes were prepared by manual separation and selection. The pure lithotypes and representative samples were ground to —35 mesh and screened to 35 x 48 mesh. The 35 x 48-mesh fraction was then passed over a magnet to remove iron contamination, washed with doubly

Jan 1, 1971

By Albert E. Ketler

Introduction – The introduction of computerized monitoring and control (M/c) equipment into the U.S. coal mining industry may prove to be of truly revolutionary proportions in the 801s.Many of you are aware that the British have developed and have been using such sophisticated M/C equipment for performing production and safety related tasks in their coal mines for nearly a decade. The benefits of M/C systems in the mining industry are usually separated into those which improve productivity, and hence make money for the company, and those which improve safety, and hence cost money. The economic benefits of M/C are startling for the production related functions such as for monitoring and controlling conveyor belts, de-watering pumps, electrical power distribution, and the like. It doesn't take much analysis to show that hundreds and even thousands of tons of coal don't get mined every time a belt shuts down or when power is out due to circuit breakers tripping for any number of reasons. A flood, caused by a malfunctioning pump which goes undetected for lack of feedback monitoring of pumping parameters, can destroy literally millions of dollars worth of mining equipment. The M/C system would be justified or not based on whether or not the productivity benefits balanced the cost within a timespan commensurate with the return on capital philosophy of the company. The safety related benefits are easily underestimated or ignored completely and the purpose of this paper is to under-score some of these benefits, as well as to review the application of M/C to the coal mining industry. The companies involved are Transmitton Ltd of England and Minetics Corp of Pittsburgh, Pennsylvania. Transmitton is probably the most experienced manufacturer of M/C equipment in the world having some 200 installations to its credit. Minetics is the marketing and manufacturing arm for Transmitton in the U.S.A. and is responsible for all aspects of distribution and service. Plans are underway for manufacturing of the Transmitton hardware for U.S. sales to be transplanted into U.S. subcontractors by 1981. Thus our coal mining industry will benefit from British technology, but without the delays and additional costs usually involved in international shipments.

Jan 1, 1981

By R. Wiesenthal

A method is developed for improving the low recovery efficiency which results when viscous oils are flooded by water. Viscous oil has been diluted with a lighter liquid miscible in it in any ratio which produces a mixture possessing a reduced viscosity and which is then displaced by water. Light gasoline was used in these tests to reduce the viscosity of the oil in place. Oils possessing viscosities in the range of 1.28 to 324 cp at the test temperature of 30C were displaced from a cylindrical unconsolidated sand core, with a length of 2 m (6.6 ft) and a diameter of 10 cm (3.9 in.) at a flood of 6.27 cc/sq cm/hr. In two test series up to I PV of light gasoline was injected into the core before water flooding. In the first series the recovery of a low-viscosity oil (1.28 cp) increased as the volume of light gasoline was increased. However, only the oil which could not be recovered by water flooding alone could be replaced by the light gasoline. In the other series, the recovery of a more viscous oil (13.5 cp) was not increased even if large quantities of light gasoline were injected. An oil bank built up ahead of the water front so that the flood water met with equivalent saturation conditions, as would be the case in flooding solely with water. However, the recovery of more viscous oils could be increased substantially when the core was first flooded with water, followed by a slug of light gasoline, and then flooded with water again. Furthermore, an oil bank ,built up ahead of the second water front. The formation of this oil bank is particularly favorable for the displacement process; the greater part of the light gasoline injected was pushed out of the core ahead of the oil and recovered. Using a light oil of low viscosity, it was possible to replace only the residual oil that could not be recovered by water flooding by the light gasoline. As the basic study had shown that highly viscous oils could be recovered by flooding first with water, then with light gasoline, followed by a second injection of water, the study was extended by tests made with reservoir fluids and cores taken from the low-gravity oil reservoir of the Wietze field, Germany. A great increase in recovery over flooding with water alone was obtained in these tests. The results may show a way to recover high-viscosity oils by a comparatively simple flooding procedure. INTRODUCTION In fields where oil recovery has not benefited from natural water drive, increased recovery may be obtained by the injection of water into the reservoir, especially in the case of fields which produce high-gravity, low-viscosity oil. There is a rather close relation between the viscosity of the reservoir fluid and the recovery that can be obtained by water flooding. As the viscosity increases the oil recovery decreases proportionately, so that an oil viscosity about 30 times that of water is generally considered to be the upper limit for an economically successful water flood.' This limitation has been recognized theoretically by Buckley and Leverett,' and has been verified by numerous laboratory flooding tests, such as by Croes and Schwarz,V n the viscosity ratio range of oil to water from 1 to 500. The reason for the inferior recovery of viscous oils by water flooding can best be understood by considering the mechanism of flood tests. In such tests water is introduced into one end of a sand-packed tube which is saturated with oil of the viscosity to be tested, and oil is produced from, the other end. Oil, with a viscosity lower than that of water, is pushed ahead of the advancing water with considerable uniformity, and irregularities in the displacement process tend to be eliminated as the oil saturation decreases and the water saturation increases. However, oil recovery is not complete, for the water forms interfaces with the oil and traps residual oil droplets in certain of the pore spaces. These residual oil droplets are distributed rather uniformly through the sand, and they are not susceptible to recovery regardless of the amount of water passed through the test cylinder. In the case of an oil possessing a viscosity greater than that of water, the injected water tends to move irregularly through the sand in the test cylinder. At the place in the sand where initial water movement takes place, resistance to the movement of water is lowered and the water finger so formed will grow perceptibly; it will extend to the outlet end of the test cylinder so that a breakthrough of water takes place long before much of the oil-saturated volume of the sand has come in contact with water. Once the breakthrough of water takes place, the water-oil ratio is gradually approaching the economic limit, even though much of the oil in the test cylinder remains unaffected by water. Disconnected drops of oil are trapped in the portion of the sand that has been invaded by water, just as when an oil of low viscosity is flooded. The poor recovery of the more viscous oils, therefore, is due to the irregularity of water movement through the test cylinder, and the rate of water movement through restricted sections of the oil-saturated sand increases with the more viscous oils. There are three ways whereby the recovery of viscous oils by water flooding can be improved:' (1) adding materials which will increase the vis-

Jan 1, 1965

Jan 1, 1927

By Michael Hoch, Michel Desjardins

The isothermal section of the Mo-Ti-Zr-0 system at 1500°C was investigated using X- ray diffraction and mefallographic techniques. Up to 66.7 at. pct 0, the system contains ten four -phase regions. Isopleths at 10, 30, 45, 55, and 60 at. pct 0 were constructed. THE purpose of this investigation was to determine the general shape of the quaternary equilibrium phase diagram of molybdenum, titanium, zirconium, and oxygen at 1500°C. The system was truncated at 66.7 at. pct o. PREVIOUS INVESTIGATIONS The Ti-Zr-0 system was investigated in this laboratory.' The binary systems of interest have been compiled and discussed by Hansen' and Levin, McMurdie, and Hall.3 Farrar, Stone, and Margolin studied the titanium-rich corner of the Ti-Mo-0 ternary. MATERIALS The titanium powder, 99.6 pct pure, the zirconium dioxide, and the molybdenum powder were supplied by the Fairmont Chemical Co. The zirconium powder,

Jan 1, 1962

By J. E. Willson, N. K. Bohidar

An evaluation of internal stress distribution based on photoelastic studies and destructive testing of simulation models shows that pillar failure is a function of the internal stress distribution, and that stability can be changed by altering the internal stress pattern. Induced stresses in three-dimensional epoxy disks subjected to uniaxial forces were evaluated by photoelastic studies. Stress profiles across different sections perpendicular to the loading direction revealed two maxima for each profile. Based on the stress distribution for the entire column, an attempt was made to explain pillar spalling and the hour glass pattern of failure in a mine pillar. For maximum stability and optimum design of mine pillars, it is necessary to consider the external forces, the nature and distribution of induced stresses and the characteristics of the pillar material as determined in the laboratory. This paper summarizes the research done by N. K. Bohidarl and Ben L. seegrniller2 as partial fulfilment of the requirement for Master of Science degree in Mining Engineering, University of Utah. It is an evaluation of a study to determine the stress distribution in short columns in order that regions of high stress concentration in mine pillars may be found and their effect on pillar failure be ascertained. The ratios of the dimensions of the columns studied are representative of those found in mines located in flat-bedded deposits. The weight of the overburden generally constitutes the major external force. This force is calculated by taking into account specific weight and thickness of the cover. Determination of the distribution of this force on pillars may often require a complex analytical study. There have been many investigations of the strength

Jan 1, 1968

By Robert D. Pehlke, Robert G. Blossey

The solubility of nitrogen in liquid binary and ternary Fe-Ni-Co alloys has been measured by the Sieverts' method between 1550°and 1700°C. Solubility data and standard free energzes and enthalpies of solution for nitrogen in the alloys are presented. Interaction parameters are discussed and presented for binary and ternary alloys. MOST of the studies of nitrogen solubility in liquid metals have been directed toward the dilute alloys of iron. Several of these investigations have included measurements of the nitrogen solubility in Fe-Ni al10s'- and in Fe-Co alloys.435 There has been some work, however, that has extended across the e-i-" and F-CO" binaries. This investigation was undertaken to determine the nitrogen solubility in both binary and ternary alloys of the Fe-Ni-Co system. It was also hoped that the differences between earlier studies might be resolved. EXPERIMENTAL METHOD This investigation was made using a Sieverts' apparatus described previously." The nickel (99.85 pct) and cobalt (99.9 pct) were obtained from Sherritt-Gordon Mines, Ltd., and the iron (99.95 pct) was Fer-rovac-E obtained from Crucible Steel Co. Recrystal-lized alumina crucibles were used throughout the entire investigation with no evidence of crucible-melt reaction. Melt temperatures were measured with an optical pyrometer and the temperature scale calibrated against the melting points of the three pure metals. The emissivity of the melt was assumed to be a linear function of composition for all alloys, as has been shown for Fe-Ni alloys.lZ The emissivity of the pure metals at 1600°C were taken as 0.43 for iron, 0.44 for cobalt, and 0.45 for nickel. Using these emissivities, the trans mis sivity of the system was found to be 0.51 i 0.01. The Sieverts' method was used for this study and followed the procedures outlined previously.l' The individual metals were weighed to give about 100 g of alloy. The alloys were melted in the crucible under a partial pressure of argon. The system was evacuated, and the "hot volume" was measured with argon. To avoid the errors caused by vaporization, the melt was held under vacuum only long enough to ensure that all of the gas in the system had been removed. The influence of any small amount of vaporization on the "hot volume" was shown to be negligible by measuring the "hot volume" after a run. This measurement agreed with that made at the start of the run within the implicit error, 0.2 cc, caused by the limitations in accurately reading the buret. The solubility-pressure relationship was measured in the pure metals and in several alloy compositions throughout the ternary system. These measurements were made by admitting measured amounts of nitrogen to the system, and then determining the equilibrium nitrogen pressure above the melt. This method has the distinct advantage of higher accuracy, particularly at lower pressures, than measurements made by withdrawing gas from the system to reduce the pressure after determining the solubility at 1 atm nitrogen pressure. This latter method has a practical lower limit of about 0.4 atm where an increased error is encountered because the buret must be emptied to permit further measurements at lower pressures. By determining the relation between apparent solubility and pressure, it was possible to make a good estimate of the initial nitrogen content of the metal from the intercept of the solubility curve extrapolated to zero pressure.11 DISCUSSION The solubility data corrected to 1 atm nitrogen pressure are summarized in Table I. The reported solubility has been corrected for the initial nitrogen content of the alloys. The initial nitrogen contents fell between 0.0002 and 0.0010 wt pct, and were lower in the iron and nickel than in the cobalt. Sieverts' law was obeyed in all alloys at pressures up to 1 atm. Examples of this behavior are shown in Fig. 1. The reaction for solution of nitrogen is Taking the standard state as 1 wt pct N in the alloy and the reference state as nitrogen at infinite dilution in the alloy, and noting the adherence to Sieverts' law, K becomes the solubility of nitrogen in the alloy at 1 atm pressure. Thus the solubility data of Table I were used directly to calculate the standard free energy for the solution reaction. These results are also presented in Table I. The enthalpy of solution is also summarized in Table I as calculated from a form of the van't Hoff relation: Iron-Nickel System. The data for the solubility of nitrogen in liquid Fe-Ni binary alloys is presented in Fig. 2 along the with data of aito, Schenck et al.,' and Humbert and 1liott.l' The data for studies of nitrogen solubility in Fe-Ni alloys containing less than 20 pc t i'- are not presented in Fig. 2, although they are in good agreement with the present work. The results of this study are in good agreement with Schenck

Jan 1, 1967

By Captain Lyle

I was very much interested in Mr. Macdonald's paper, and I can say that there is nothing in it to which I cannot heartily subscribe. In speaking of the want of knowledge that has existed, and still exists, among engineers in regard to structural materials, their strength, etc., my own experience has taught me to doubt the reliability of the ordinary testing machines.

Jan 1, 1882

NATURE produces iron ore abundantly in many regions of the world, especially in Italy where not only is there a great abundance of it but also there are various kinds. In these our Tuscan parts it is a very familiar thing, since we are situated close to the island of Elba which is so overflowing and rich in this ore that it surpasses every other place where it is found. Thus not only do the regions of Tuscany share its great quantity because of their proximity, but more than two-thirds of Italy as well as Sicily and Corsica are supplied, and perhaps some more distant place. In addition, this ore is of such perfection that it

Jan 1, 1942