Search Documents

By E. I. Larsen, E. F. Swazy, F. R. Hensel

High strength, high-conductivity copper-base alloys have found considerable use in the resistance welding and electrical industry in the form of castings, forgings, or wrought products. There are a number of parts utilized by these industries which would lend themselves to manufacture by powder metallurgical methods provided the required physical and electrical properties are obtainable with such methods. The present paper describes the results of a study of certain copper-base powder metallurgical products susceptible to precipitation hardening. Copper Powders The general types of commercially available copper powders are flake, spherical and electrolytic. Micrographs of these three types are shown in Figs. I, 2 and 3. The difference in particle shape is pronounced and obvious. The type of powder used is determined, or at least indicated, by the final properties desired in the finished article. The type of powder employed during the present investigation was electrolytic powder shown in Fig. 3, and was chosen because of its particular adaptability to the work described in this Paper. The screen and chemical analyses of this powder are shown in Table I. In the preparation of compacts of high electrical conductivity, the purity of the copper powder is of importance in addition to other factors, such as density and the state of internal stresses. These variables were studied briefly by pressing a number of compacts to various pressed densities, sintering them for one hour in hydrogen at 975OC and repressing. The size of the finished compacts was 1/4, by % by 8 in. The time interval from the application to the termination of pressure was approximately 20 sec. Some of the compacts were annealed before testing. The results are listed in Figs. 4 to 8, inclusive. In Fig. 4 the curves of pressed density vs. compacting pressure, and sintered density versus compacting pressure show the typical direct relationship of pressure and density. Compacting pressures exceeding about 30 tons per sq. in. result fiequently in expansion during sintering for the type of powder used. Fig. 5 indicates that variations in the initial pressed density within the range of about 5 to 6 grams per c, c., affect only slightly the pressure required to obtain a

Jan 1, 1946

By V. Lessels, W. A. Hamilton

White Pine Copper Co. is a wholly owned subsidiary of the Copper Range Co. The property of White Pine is about 5 miles south of Lake Superior in Carp Lake Township, Ontonagon County, Mich. The new town of White Pine, adjacent to the company plant, is 18 miles south and west of the town of Ontonagon, and about 55 miles north and east of Ironwood, Mich. A diamond drilling program begun in 1937 to develop the orebody was carried on until 1950. During this period a test shaft, known as the Schacht shaft, was sunk on the orebody and approximately 8000 ft of development drift were driven. In an effort to solve the ore beneficiation problems, considerable metallurgical test work was done on ore extracted through the mine development. This work was conducted in a small pilot plant located in the mill of the Copper Range Co. at Freda, Mich.

May 1, 1956

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1693 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. I. B. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs and Mine Management 156, Ataturk Bulvarl-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" B Howard-Canfield Bldg. Santa Barbara, Calif. COWIN & Co. Mining Engineers and Contractors Consulting Shaft & Slope Sinking Appraisal Mine Development Reports Mine Plant Construction I- 18th St. S. W. B'ham, Ala., Phone 56-5566]

Jan 1, 1952

By I. R. Kramer

The delay time for single crystals of iron, zinc, and pre-strained aluminum was measured under conditions of high-speed deformation. The delay time of aluminum was found to be affected by the orientation of the crystal. Under the dynamic conditions employed, tile calculated "activated volume" term appears to be very small for the three metals studied. IN a previous paper,1 it was shown that under dynamic testing conditions at 78° K, there was a delayed yield in single crystals of aluminum and copper which had been cold-worked prior to testing. The experimental results also indicated that the delay-time effect was not due to the interaction of dislocations with impurity atoms or vacancies, but rather to a dislocation-dislocation interaction since aluminum which has not been prestrained shows no delay-time phenomenon. In this paper, some data are reported on the effects of orientation on the delay time of aluminum single crystals; the delay time of zinc single crystals saturated with nitrogen and the delay time of iron single crystals also were measured. EXPERIMENTAL PROCEDURE Aluminum (99.997 pct) and zinc (99.999 pct) crystals, 1/2 in. in diam and 8 in. long were grown by the Bridgman technique. The iron single crystal was supplied by Dr. R. Maddin. The zinc crystals containing nitrogen were prepared by melting high-purity zinc in a graphite crucible and the nitrogen was introduced by additions of ammonium chloride. The liquid zinc was then drawn up into glass tubes of 1/2 in. diam and allowed to solidify. The rods were cooled to room temperature before the transfer to the mold for conversion into single crystals. The orientation of all specimens was determined by the Laue' back-reflection technique, Fig. 2 and Table I. To prepare for the delay-time measurements, the crystals were cut with a fine jewelers saw and the ends carefully machined. The specimens then were electrolytic ally polished to remove the cold-worked metal, mounted in a special fixture and hand-lapped. As a final step, the crystals were annealed in evacuated tubes. Specimens of aluminum crystals, Nos. 24 and 26, were compressed 0.5 and 2 pct, respectively, in the direction of the later impact. The zinc specimens were aged at 50°C for 15 min, In the case of iron, only two specimens could be obtained. To obtain sufficient data, it was necessary to resort to a reaging treatment. After each delay-time test, the specimens were aged at 65° C for 100 min. This treatment, according to Clark,2 is sufficient to restore the original delay time. It is believed that although the specimens were plastically deformed approximately 10-4 pct, after each test the delay-time values are reliable. The delay-time measurements were made in an apparatus similar to that described previously.' Single crystals approximately 1 in. long and having a diameter of 1/2 in. were placed in a pendulum which consisted of a bar 1/2 in. in diam and 8 ft long, designed with a crystal holder to accommodate the specimen at low temperatures. The crystal was held at a position 2 ft from the front part of the pendulum. This portion of the apparatus was supported on a fine molybdenum wire. A projectile bar of the same diameter and length comprised the other portion of the apparatus. This bar was supported on

Jan 1, 1962

By Robert P. Uhley, LeRoy Scharon

TEST gravity surveys were made in the Washington County barite district of Missouri on property owned by the Baroid Sales Division of the National Lead Co. This property is located just northeast of Richwoods in the northeastern corner of Washington County, Fig. 1. The area to which the surveys were confined comprised approximately 5000 acres, of which some 525 acres were surveyed gravitationally. Gravity observations were made at 2600 points within the area, observations being confined to relatively clear and gently sloping ground. Part of the area was heavily wooded, and the terrain too rugged for either the occurrence of a commercial barite deposit or a feasible gravity survey. The relief along the central drainage, Ditch Creek, was about 140 ft, the maxi- mum difference in elevation being 400 ft in a distance of 3 ½ miles.

Jan 1, 1954

By Albert Sauveur

The instrument about to be described meets so perfectly the special needs of the metal microscopist that there eeeme to be little doubt but its merits must be readily appreciated by those who have had any experience in the microscopical examination of metals. The Microscope-Stand.—The microscope-stand proper, Fig. 1, consists of a microscope-tube, provided with both coarse and fine adjustments of the best construction, and with a draw-tube, rigidly mounted on a bar supported at both ends on substantial and firm cast-iron legs. The height between the table and the under side of the supporting bar is 5 in. and the distance between the supporting legs 12 inches. This arrangement affords free space below the objective for the examination of large epecimens of metals, such as full rail-sections, without detracting in the least from the value of the

Jan 1, 1912

(The following list contains the names of those members of the Institute of whose connection with military service we have only recently become acquainted; it also includes the navies of a few who have recently been promoted or transferred. A complete list was published in the Year Book, issued as a supplement of the Bulletin for March, 1918.) ARNOLD, RALPH, Member of. Board of Tax Reviewers in connection with the administration of the War Revenue Act. BACON, RAYMOND F., Lieutenant-Colonel, Chemical Service Section, N. A., A. E. F. BALLENBERG, A. G., 1st Lieutenant, Ordnance Dept., U. S. A. BARCUS, WALTER J. E., Captain, Gun Division, Ordnance Officers' Reserve Corps. BECKWITH, H. T., Captain, Engineer Reserve Corps, Headquarters Co., 312th Engineers.

Jan 6, 1918

By R. B. Walker, R. Palmer, L. C. Bryner

The purpose of this investigation was to further study some of the factors affecting the air oxidation of sulfide minerals. Data obtained from laboratory studies on the effect of temperature, concentration of iron salts, pH, and other catalysts on the biological and nonbiological oxidation of sulfide minerals are presented. The oxidation of copper sulfide minerals and subsequent leaching of the soluble copper has long been a profitable operation. The chief oxidizing agent is oxygen from the air. This reaction is influenced by a number of different factors such as temperature, light, hydrogen ion concentration, oxidizing agents, and various catalysts. Sullivan1 found that copper sulfide minerals are slowly oxidized by the air and that dilute sulfuric acid and iron (111) increased their solubility. At that time it was not known that bacteria were involved in the oxidation of the sulfide minerals. It has been shown that pyrite, molybdenite, free sulfur, and the copper sulfide minerals found in the waste rock dumps in Bingham Canyon, Utah, are largely oxidized by chemosynthetic autotrophic microorganisms found in the leaching streams.2-6 Similar organisms have been isolated in other mining areas7,8 and from the effluents from coal rnines.9 The following are some of the questions that have arisen regarding the mechanisms of the reactions involved in the leaching process. How dependent is the leaching operation upon the biological reactions? How does the temperature effect the biological and non-biological reactions? How does the concentration of iron (II) and (111) effect the rate of oxidation of copper (II) sulfide? Does the iron act as a catalyst? Does activated carbon act as a catalyst on the oxidation of sulfide minerals? What effect does the hydrogen ion concentration (pH) have on the above reactions? The purpose of this paper is to report the results of laboratory studies on these problems. EXPERIMENTAL The apparatus used in this investigation was an air lift percolator described in our earlier work.' The percolator consisted essentially of an air lift which enabled the leaching solution and microorganisms to pass freely through a suspension of mineral (substrate) in Ottawa sand. The air lift served the additional purpose of maintaining an ample concentration of oxygen and carbon dioxide in the nutrient (leaching) solution. (See Fig. 1.) The percolators were so constructed that they could be immersed in liquid constant temperature baths for temperature studies. The thermostats were controlled to +0.5°C. The reactions were all run in the dark. The percolators were charged with one to three g of mineral, dispersed in 100 g of Ottawa sand and 100 ml of nutrient or leaching solution. The sand was purified to remove traces of iron by digesting with concentrated hydrochloric acid and washng with distilled water until free from chloride. After drying, the sand was ready for use. The compressed air supply was regulated to 5 psi and bubbled through an aerator containing distilled water, which was maintained at the same temperature as the bath used. The air was filtered through cotton plugs to maintain sterile conditions. The tops of the

Jan 1, 1968

By C. H. Frick

Before presenting the main topic, as indicated by the title, this paper will give some of the high-spot history of the anthracite industry. Introduction The earliest recorded use of anthracite was in the year 1762, when a company of Connecticut pioneers discovered anthracite near the present city of Wilkes-Barre, Pennsylvania. In the early days of the industry, the coal was used only in large pieces, the smaller pieces being discarded to waste piles. As the output of the industry increased during the nineteenth century, uses were developed for somewhat smaller sizes down to and including pea coal. Early in the twentieth century, sizes smaller than pea, such as No. I and No. 2 buckwheat, were developed and used. Accumulations of piles from current mining operations were still increasing; that is, the smaller sizes were still being discarded. It was not until after World War I that preparation of the so-called steam sizes began commercially. This was largely No. 3 buckwheat, which is screened through a 3/16-in. round-hole screen and over a 3/32-in. or a 1/16-in. round-hole screen. Use of Smaller Sizes The earliest recorded experience in burning the small sizes of anthracite for steam production, other than in a previous small experiment, was in the year 1913, when a size known as "boiler fuel" was introduced—a mixture of rice and barley (No. 2 and No. 3 buckwheat). At that time, there was still no method known for burning the still smaller sizes. At the present time, various sizes down to and including No. 5 buckwheat are being prepared (Table I) from current mining and bank-reclaiming operations. The sizes of No. 4 and No. 5 buckwheat and smaller are generally being used for steam production in large boilers. The Pennsylvania Power and Light Co., following World War I, used 680,000 tons of anthracite per year, burned largely on stokers for production of steam, whereas for the year 1943 it used 1,940,000 tons of stoker sizes and 400,000 tons of smaller sizes for grinding and burning in pulverized form. This company has taken a very large part in the research and development of ways and means of burning these smaller sizes of anthracite, including the grinding of the very small sizes. This paper is particularly concerned with the latter feature.

Jan 1, 1949

By J. P. Givry

The bath and the liquid metal in the aluw~inuw~ electrolytic cells are moving under the action of the Laplace forces. Consequently there are differences in level at the interface of the liquid. This phenomena is studied by means of a computer; the characteristics of the mathematical model used are presented with the results corresponding to two typical cases. This study gives a new and origi~zal interpretation of magnetic ej-jects; their action depends very closely on the hydraulic phenomenon which explain the sensibility of the cells to the slope and thickness of solid bath frozen around the pot. MAGNETIC effects produced in the electrolytic cells used for the production of aluminum are known to exist, a factor whose importance is well-known by producers through its influence on cell operation and output. In particular, these effects bring about movements in both the bath and metal as well as interface variations in level that are detrimental to sound electrolysis . A direct study of these effects by means of an experimental device would raise a number of problems particularly difficult not to say impossible to solve in the present state of techniques. It is for this reason that we had recourse to an electronic computer for working out the speed and pressure distribution within the liquid in the cells. We have assumed that all other possible causes for movement, such as thermal convection and evolution of gas at the anode, are acting without any connection with magnetic effects, and that consequently we may study each of these causes separately. A basic cause for magnetic effects lies in the presence of Laplace forces within the bath and metal. Electric current and magnetic field distribution have been calculated with the help of an electronic computer, and two communications about it have already been made to AIME.* 1) PRESENTATION OF THE MATHEMATICAL PATTERN In order to solve this problem, it was essential to assume a number of simplifying hypotheses with regard to both the geometry of the actual cells and the phenomena themselves. A first simplification consisted in assuming that the movements of the conducting liquid modify neither the electric currents nor the magnetic fields. In consideration of the magnitude of the values involved this assumption seemed accep-tible. 1.1) Finding the Equation of the Problem. The problem raised consisted in determining the flow of two viscous immiscible liquids with different densities subjected in a complex environment to gravity and Laplace forces. As a matter of fact, the sum of the external forces acting on the liquids is: F = JAB +pg where F = volume energy, B = magnetic field, J = current density, p = specific gravity, g = gravity. In the case of a laminar flow and assuming that the liquids are Newtonian and incompressible liquids, the equations governing movements are the following: 1) Navier Stokes' equation written in vectorial form: In fact one tries to find a steady-state solution, so aVx/at = 0; besides, one assumes that the movements are slow enough for quadratic terms such as Vy(a Vx/ay) (of round about the square of speed) to be neglected in front of the viscosity term: pAV, so

Jan 1, 1968

G. R. GOHN. l-1n Table I11 of The Sager, Brown, and Mears paper, which was presented on the screen, data were given showing the results of accelerated corrosion tests of certain magnesium alloys. Mention was made that these were carried to a certain time which was used as a measure of failure but no mention was made as to the period of time. I would like enlightenment on that. G. F. SAGER (Author).-In reply to Mr. Gohn's question regarding the times of exposure for the accelerated stress-corrosion tests referred to in Table I11 of our paper, which shows the correlation between accelerated and atmospheric stress-corrosion tests on magnesium alloys, I can say that we usually run the accelerated tests on such alloys for at least 500 hr. We feel that this is long enough to reveal any marked susceptibility to stress-corrosion cracking. In the case of the atmospheric tests on such alloys, we have not yet decided how long we should expose the specimens. Most of them are being exposed for indefinite periods and a good many of our specimens have now been exposed for several years. We may want to continue some of the tests for five or ten years. The period of six months mentioned in connection with the times of exposure for the atmospheric specimens was a rather arbitrarily selected minimum time for which specimens had to be exposed before we counted them with those that had not failed. A fairly large number of magnesium- alloy specimens have been exposed in the atmospheric stress-corrosion tests at var-

Jan 1, 1945

By A. L. Holley

THOSE who are familiar with working gas furnaces will perhaps admit that the ordinary producer is the least satisfactory feature of the- whole system, chiefly by reason of its great waste of fuel, both above and below the fire. The waste of fuel in cleaning the fire has not, as far as I am aware, been carefully measured ; it has been roughly estimated at various works as averaging twenty per cent. to twenty-five per cent. The coke that falls into the ash-pit is largely mixed, if not stuck together with clinker; when this coke is not recovered and utilized (and where coal is cheap it does not pay to recover it), the waste is certainly as high as above estimated. Cleaning a fire on a grate (especially a fire of dirty coal, like much of our Western coal), by inserting a few temporary grate-bars, then withdrawing the regular grate-bars and letting the whole lower part of the fire tumble into the ash-pit, must necessarily be wasteful of fuel, but it has been found to be the most practical system. The fire under a boiler should be thin, to insure perfect combustion; hence it may be moved from one side to the other, so that .the clinker and ashes may be uncovered and removed. But a producer fire should be so thick that carbonic oxide only shall rise from it ; a thick fire cannot be thus manipulated. In several of the French works the ordinary producer without grates is employed ; the whole body of the fire rests on the floor of the ash-pit. It did not seem to me that less fuel was wasted here than with grates in cleaning fires. The bottom layer of the fire had to be drawn out with hooks, and there was nothing to prevent much coke from coming away with the clinker and ash. A producer shaped like a cupola furnace has many advantages, but if grates are employed the waste of coke in cleaning is not lessened. But the waste at the bottom of the fire is only a part of the waste in the ordinary producer. Mr. Emmerton, chemist to the Joliet Iron and Steel Company, has lately made a number of gas analyses from the producers of that company, worked with impure Illinois

Jan 1, 1880

By J. B. Austin

IN developing a consistent picture of the thermal expansion of the commercial chromium steels, which cover a range of carbon contents, it is desirable to know the expansion in the limiting case of the binary, carbon-free, iron-chromium alloys. We have, therefore, determined the thermal expansion of a series of five special alloys, ranging in chromium content from 3 to 10.5 per cent, with not more than 0.03 per cent carbon, over a temperature range extending beyond the transformation region; this low carbon content enables us to draw reasonably reliable conclusions as to the behavior of the carbon-free system. Moreover, the measure-ments serve to determine the beginning and the end of the alpha-gamma transformation; and they emphasize once more the fact that a transforma-tion temperature determined by any method in which the specimen is cooled at an appreciable rate is apt to be seriously in error, particularly if the metal contains a transformation-retarding element such as chro-mium or managanese. The lag, or undercooling, observed at the ? - a transformation is explained in terms of the influence of temperature on transformation velocity; the rather unusual shape of the ? loop is attributed to a change with temperature and with composition of the distribution of chromium between the alpha-iron and gamma-iron solid solutions. The exact composition of the alloys which were obtained through the courtesy of Dr. W. Rohn, of the Heraeus Vakuumschmelze A-G., is given in Table 1. Determinations of the linear thermal expansion and of transformation temperature were carried out in the vacuum dila-tometer previously described,1 using a rate of heating and of cooling of 3.0° to 3.5° per minute unless otherwise stated. Magnetic susceptibility, which was measured in studying the rate of transformation, was determined with a magnetic balance, which also has been described.2

Jan 1, 1935

By David C. Yang

INTRODUCTION Over the world, and especially in the United States, there is increasing dependence upon progressively lower grade ore deposits. These lower grade ores are frequently difficult or impossible to process due to complex mineral assemblages being very finely disseminated. Thus, many of the conventional mineral concentration methods are not applicable to these ores. For the last few decades, research in the more exotic mineral processing techniques has been conducted, both in universities and in governmental and industrial laboratories. Since its inception, the Institute of Mineral Research of Michigan Technological University (MTU) has devoted much of its attention to the problems of processing refractory, low grade ores. Recently a new flotation system was developed which shows promise of being applicable to a broad range of ore types. This process has been the subject of two allowed patent applications. This paper describes the details of such a flotation system which is potentially useful for treating ultrafine minerals. Some highlights of the testing program on a variety of iron ores and a group of lithium-bearing ores will be presented. EXPERIMENTAL PROCEDURES Both iron and lithium ore flotation treatments followed the same general procedures, with minor differences in pH and in reagent dosages. The method is rather simple, efficient and economical from the standpoint of recovery and the cost of reagents consumed.

Jan 1, 1979

By A. L. Mular

The flotability of crushed zinc oxide pellets which were doped to produce more n-type or less n-type (more p-type) properties was studied with a Halli-mond tube. Flotation data are presented to show that the pH at which 50% recovery occurs and the collector concentration for 50% recovery depends upon the concentration of doping agent added substitu-tionally for zinc in zinc oxide. The time of sintering of pellets has a slight effect on flotation behavior. A speculative model is proposed to explain the observed behavior in light of the fact that zinc oxide is a semiconductor and has a space charge region at the surface. Experimental verification is necessary before the proposed model can be established as correct. In recent years, the attachment of flotation reagents to minerals has been shown to depend upon the behavior of an electrical double layer which exists in the liquid near the mineral-liquid interface.' Thus, a mineral placed in water will undergo a surface re-arrangement, most likely be preferential dissociation of lattice atoms or by surface adsorp-tion-desorption reactions, to form a dissociation electrical double layer with the solution. Among the many factors which influence adsorption processes, the past history of the mineral itself is one of the most important. Because of trace impurities, minerals from different localities may exhibit marked differences in flotation behavior. This is not unexpected, since investigators who have studied the detailed structure of the double layer's3 have known for some time that the impurity content of many minerals may exert strong influence on double layer variables. For this reason, their studies were usually made with minerals of high purity. The precise relationship between impurities in a mineral and double layer parameters such as capacity and electrostatic potential has been obscure. However, impurities in a semiconductor type mineral which is in contact with a solution have been recently shown to produce changes in the properties of a space charge layer which extends into the bulk of the semiconductor to a distance of one micron or more.4 The double layer is influenced by the space charge layer, whose origin is best discussed in terms of the band theory of solids. A qualitative description of the behavior of impurities in the bulk of a semiconductor, from a chemical point of view, is useful at this point. Briefly, impurities or defects (lattice vacancies, interstitials, etc.) in semiconductors such as PbS, ZnS, FeS2, Cu2S, NiS, NiO, Fe2O3, ZnO, CdS, MnO2 and many others, behave somewhat like acids or bases in water. For example, water dissociates into hydrogen and hydroxyl ions according to

Jan 1, 1965

By Stanley J. LeFond

Jan 1, 1985

By C. E. Berry

NATURAL stone or manufactured porcelain pebbles are used as the grinding elements in pebble mills and the mills are lined with stone or porcelain blocks. Steel balls usually form the grinding medium in ball mills, and the mills may he lined with steel. Pebble mills are used to avoid contamination by metal of the material being ground, to avoid rapid wear due to corrosion, and for other specialized reasons. Belgian silex (silica) blocks formerly were used widely for lining pebble mills, because of their good resistance to wear, light color, and low cost, but the importation of these blocks was suspended early in the war. The stocks of Belgian silex diminished so rapidly that it was found desirable to compare the properties of a number of domestic substitutes for use in critical operations. Accordingly, a study was made to determine the best substitutes for fine grinding of white pigment and for certain heavy-chemical process work such as the disintegration of phosphate rock in weak phosphoric acid solution. A comprehensive survey of substitute lining materials was not contemplated. It was stipulated at the beginning of the investigation that only materials on the market, available in large quantities, would be tested and that these should be reasonable substitutes from a wear-resistance viewpoint as determined from known physical characteristics. Marble and limestone, for example, could be eliminated immediately. Quartzite, granite and porcelain were selected as likely substitutes for Belgian silex and were subjected to quality tests. MATERIALS TESTED I. Belgian Silex.-Sample blocks of a standard grade were taken from crates in which they had been imported. The stone was light gray in color and contained inclusions of small clusters of quartz crystals as well as light colored portions that might be calcite. This was a siliceous rock which appeared to be of igneous origin. 2. Quartzite.-Samples of quartzite were obtained from a quarry in Minnesota. The blocks exhibited a crystalline fracture. The stone was pink in color and composed of fine quartz crystals bound together with a siliceous cement. 3. Granite A was a fine-grained granite quarried in South Carolina. 4. Granite B was coarse-grained granite quarried in South Carolina. 5. Granite C was a coarse-grained granite quarried in North Carolina. 6. Porcelain A.-Sample blocks of the pebble-mill lining material were obtained direct from the manufacturer. It was white in color and of lower specific gravity than the natural materials. It did not have a crystalline structure. 7. Porcelain B.-Sample pebble-mill lining blocks of the porcelain were received direct from the manufacturer. It was white

Jan 1, 1946

By Henry M. Howe

This paper is a discussion of the extremely valuable one of Mathewson and Phillips, The Recrystallization of Cold-Worked Alpha Brass on Annealing,1 which not only gives us a wealth of important data reached with great intelligence, but also shows both uncommon powers of imagination and a perfectly fair spirit. Let me try to analyze some of their results, and to enunciate some of the laws to which these results point. For brevity I refer to them as "The Authors." The page numbers in parentheses refer to their paper. 1. The Visible Aspects of Recrystallization.—Plastic deformation in a single direction, as in cold-rolling, draws the grains out in that direction, that is, inequiaxes them, without destroying their apparent individuality. Each grain seems to endure the drawing out without changing either its volume or its orientation materially, for the etching tint of each grain seems to be as uniform after as before the drawing out, save for the "etch bands,"2 shown in Figs. A to D of the Authors' Plate I. As the drawn-out metal is heated progressively, on reaching a certain "disintegration temperature" these old grains seem to break up, probably into submicroscopic fragments, and this apparent disintegration is followed by a coalescence of these fragments, so that their number decreases and their size increases, till they may become very much coarser than before the drawing out. Ruder3 coarsened the grains of silicon steel in this way till single grains reached an area of 50 cm. (7.75 sq. in.). The deformation itself probably breaks each grain up into many very small fragments, but the fact that each grain continues to have a uniform etching tint different from that of its neighbors indicates that these fragments retain the initial common orientation of the grain. The apparent disintegration which we observe, then, is rather an abandonment of community of orientation for individuality of orientation, by the fragments formed earlier during the deformation. Hence we

Jan 1, 1917

By S. M. Runke, R. G. Meara, O&apos

The Bureau of Mines has been charged by Congress to investigate processes for the production of alumina from low-grade bauxite, alunite, and clay. As one part of the program, an investigation of the application of ore-dressing methods to improve the grade of high-silica bauxite is in progress at the Mississippi Valley Experiment Station at Rolla, Mo. This paper summarizes data obtained so far and presents detailcd results of tests on four typical samples. Mineralogy of Batjxite The name bauxite originally was used to designate the dihydrous aluminum oxide (A1203.2HzO). The designation has been retained, although the existence of a specific mineral of such composition has been disproved. The term is now applied to ores of aluminum consisting of various mixtures of the minerals gibbsite (AlzOa.3H20), diaspore (A120a.H20), and boehmite (Alr-03.H20). The predominant hydrous aluminum oxide in most American bauxite, however, is gibbsite. In some instances bauxite may be amorphous mixtures of the hydrous aluminum oxides that approximate the composition of dihydrous aluminum oxide (A1203.2Hz0). The proposed name for this material is cliachite. Gibbsite and boehmite, the trihydrate and monohydrate, are soluble in a solution of sodium hydroxide at elevated temperature and pressure, whereas diaspore is practically insoluble. The solubility of these two minerals is the basis of the Bayer process of alumina extraction. All bauxites contain certain impurities, the commonest of which, in the order of their importance, are: silica, principally as a constituent of kaolinite, and to a lesser extent as quartz; iron, as hematite, limonite, and siderite; and titanium, as ilmenite, rutile and leucoxene. Minor impurities are zircon, cobalt and nickel. Bauxite is produced commercially in Arkansas, Alabama, Mississippi, Georgia and Tennessee, but the most important deposits in the United States are in Arkansas, in the vicinity of Little Rock. History of Batjxite Beneficiatjon The literature on bauxite beneficiation is limited, but the reports of Gandrud and DeVaneyl and Clemmer, Clemmons, and Stacy2 show the possibilities of flotation as a means of beneficiating bauxite. Their work has also developed reagent combinations that are satisfactory for flotation of gibbsite.

Jan 1, 1944

By David K. Hylbert

This study investigated roof falls in room-and-pillar drift coal mines in eastern Kentucky and utilized geologic methods for predicting roof conditions in advance of mining. In the Highsplint mine, the roof was classified in four categories or conditions: Condition A and B (Laminated Shale); Condition C (Rolling Sandstone with Shale in Pockets); and Condition D (Zone of Major Sandstone Roll(s)). Structure contour and isopach maps of the Darby coal bed and associated immediate roof rocks were wed to project axial trends of the sandstone roof. Trend mapping in the mine and on outcrop provided more detailed control for roof projections.

Jan 12, 1978