Search Documents

Jan 1, 1944

1910, hundreds of thousands of dollars of work and equipment in a 1500-foot shaft, crosscuts and pumping had found only copper-lean pyrite in two cross- cuts, and nothing in a third. Going aimlessly along the third crosscut one day, after looking at the barren face I happened to notice a dark spot in the white limestone, near the floor on one side. I picked, and found it was a little triangle of rich chalcopyrite. Next day I took Bill Gohring, then mine superintendent, in to see it. He said nothing else had succeeded so we might as well try that. The new drift broke into a full face of high grade copper ore in the first round, and continued in rich ore for 2200 feel broken only by a couple of short stretches of lean pyrite. The earlier crosscuts had happened to cut these lean areas. Q: Was there any single thing that called your attention to that little dark spot in the side of the Briggs crosscut, rather than to any other discolored spot? Joralemon: Nothing very definite. Maybe luck, maybe that indefinable subconscious thinking that

Jan 9, 1964

By A. L. Field

Previous Publications THE first report on the slag viscosity work of the Bureau of Mines was made by one of the authors 1 in 1916. It was concerned chiefly with, the method of measurement. A paper 2 on this phase of the work was presented to the Institute in February, 1917, and a similar paper 3 was communicated to the Faraday Society. Purpose and Scope of the Slag Viscosity Tables Following the development of a suitable method, the next step in the investigation was the measurement of slag viscosity over a wide range of temperature and composition, and the arrangement of this experimental data in the form of tables for the use of the blast-furnace operator. It is believed that this information, if used intelligently, should help the operator to reduce losses in production caused by off-grade pig iron, to improve fuel economy, to promote operating efficiency, and to extend present-day practice to meet the increasing need of smelting lean and complex ores. In the experimental part of the work it was early observed that the temperature-viscosity relations of a slag were determined, for practical purposes, by the relative proportions of the three major constituents, lime (CaO), alumina (Al203), and silica (Si02), provided the percentage

Jan 12, 1917

Experimentation which measures differences in pressure across the interfaces of immiscible fluids in the interstitial spaces of porous media may be termed "capillary pressure experimentation". In the literature of petroleum technology since 1941 there have appeared twelve papers popularizing capillary pressure concepts and developing applications of these concepts for the solution of problems of practical reservoir engineering importance, such as the determination of connate water, fluid distribution. in transition zones, reservoir rock textural properties, and oil recovery from petroleum reservoirs.' Although a review of the literature would be justified at this time in order to reconcile the conflicting viewpoints which are contained in the cited papers, the object of this note will be of more limited scope. It is believed that the recent paper of Muskat alls sufficient attention to many of the uncertainties which arise upon examination of the published literature. such that until satisfactory counter-proposals can be made it will serve our purpose only to mention some other like uncertainties. This will emphasize further the need confronting petroleum technologists to re. consider and reformulate the application possibilities of capillary pressure experimentation. In particular, I sug- gest that we examine the thesis that capillary pressure experimentation as above defined can lead to measurements reflecting the recovery of oil from petroleum reservoirs, as was proposed first" by Amyx and Yuster" and was first reduced to practice by the experimentation of Welge. In fact. I shall deal exclusively with the Welge papers since it is the principle one on this subject which has appeared to date. I shall attempt to show that the possibility of describing oil recovery features in terms of capillary pressure phenomena has not been established entirely. The Welge paper was a pioneering effort to evaluate this recovery application possibility. P. P. Reichertz' comments on the Welge paper state that non-wetting phase discontinuities are developed occasionally in the Welge experiment, and restate Muskat's argument that discontinuous fluid elements (partially saturating the interstices of porous media which are elsewhere saturated with some other immiscible phase or phases) are not subject to the requirements of hydrostatic equilibrium. It is the purpose of my comment to show that it is unnecessary to make Reichertz' postulation regarding non-wetting phase discontinuities (however valid) when it is desired to criticize welge's theoretical treatment of his problem. It can be shown that Welge's method of measuring values for ''capillary pressure" is invalid in many instances of application, such that his reported curves of capillary pressure Versus fluid saturation often have no physical meaning, even throughout the interval of fluid saturation where it might be otherwise suspected that no phase discontinuities occur. By considering established principles of capillary pressure experimentation it can be shown that the pressure difference experimentally observed between wetting and non-wetting fluid Phases which are contained in external reservoirs will reflect on the capillary pressure difference at the interfaces of contact between these phases only when the following conditions are satisfied: (a) There shall be a balance between the opposing forces of gravity and capillarity, as obtains under conditions of hydrostatic equilibrium when the positions of the interfaces of contact become fixed in pore spaces of certain geometry (b) The wetting and non-wetting fluids within the interstitial spaces shall everywhere be continuous with the external wetting phase reservoir and the external non-wetting phase reservoir, respectively. It will become apparent immediately that in any instance when a greater pressure is recorded in the external wetting phase reservoir than in the external non-wetting phase reservoir, one may establish either that static equilibrium has not been attained or that discontinuities in one or more of the fluids have been developed. This is because the pressure otherwiee is always ereatest in the non-wetting phase at each static interstitial interface of contact with the wetting phase. such that the externally measured pressure in the non-wetting phase likewise must be greatest if the above conditions are to be satisfied.

Jan 1, 1949

By C. H. Jr. Herty

THE elimination of metalloids in the open-hearth process depends on oxidation of the metal by diffusion of FeO from the slag (or absorption of FeO by the metal), with subsequent reaction between dissolved iron oxide and the metalloids carbon, manganese, phosphorus, and silicon. During an investigation on deoxidation with silicon, data on rate of oxidation of the metal were obtained, and these combined with certain other information, are presented here in an attempt to show the fundamental principles governing the diffusion of FeO from slag to metal. Inasmuch as the aim of the investigation was not a study of diffusion, certain data are lacking and it has been necessary to make assumptions on metal viscosity and effect of temperature on diffusion. These factors are known to exert a considerable effect on diffusional processes. Overoxidation, or supersaturation of the metal with iron oxide, is not taken up in this paper. Overoxidation has little effect on diffusion except under a few special conditions, and the discussion has therefore been limited to diffusional processes. Though the results given in this paper should be regarded as preliminary, certain of the conclusions drawn are definitely applicable to any steelmaking process.

Jan 1, 1929

By Arthur Taggart

THE major portion of the work described in this paper was performed by R. W. Young,+ a graduate student in the department of Mining and Metallurgy, Sheffield Scientific School, Yale University, working under a cooperative agreement between the Hardinge Conical Mill Co., the Sheffield Scientific School, and himself. Since this cooperative scheme is at present in effect in the case of a considerable number of other students in the department and since it is the hope of the school that the privilege thus extended may be utilized even more freely in the future by mining and manufacturing companies, it may not be amiss at this point to give a summary of the general plan. Briefly it is as follows: A graduate student, whose undergraduate work in this or other universities shows promise of ability to handle research work, is chosen by conference between the company and instructor involved. The aim of the company in the agreement then entered into is to obtain the solution of one or more of the technical problems with which it may be confronted, or, at the end of 1 or 2 years, to obtain as an employee a man especially trained in its work. As. a means to accomplish one or both of these ends, the company furnishes the machine, apparatus, or material to be tested and pays the student during his graduate work a small salary, usually just sufficient to cover his living expenses, tuition and fees. The aim of the student is special training along a line in which he is particularly interested, the attainment of his advanced degree, and the chance to show to his future employer ability to handle such problems as may be presented to him. In return for the financial aid which he receives he agrees to devote at least half of his working time to the special problem submitted by his company. The other half is devoted to study of the collateral subjects required by the department for the granting of the degree which the student seeks. The student further agrees to enter the employ of the company in question at a wage not greater than that paid in like positions to recent graduates not specially trained and to remain with his employer at such wage for at least 1 year. If the student is to obtain a degree, the special work forming the basis of his investigation must be such as will involve real research and not mere routine manipulation. The subject is chosen by conference between the three parties to the agreement. The work is carried on under the direct supervision of the instructor involved. The school furnishes the general laboratory and library equipment essential to the pursuit of any extended investigation, In

Jan 4, 1917

By E. H. Lovitt, A. C. Skerl

After nine years of continuous operation it is a good idea to take stock of the geological concepts that guide the working of a mine. This is a welcome opportunity to discuss the Lovitt gold mine, which has been a challenge in both the geological and operational fields. The occurrence belongs to the extensive group of epithermal gold-silver deposits once worked so vigorously in the western states, Hungary, and New Zealand and still producing in Central America and the Philippines. These deposits are characterized by a relatively shallow vertical range up to 2000 ft, and often much less, and by bonanza orebodies of even more limited range. The area in which they occur is frequently widespread, so that exploration must be directed along and across the strike of known favorable structures in search of repetitions.

Jan 9, 1958

By W. H. Newhouse

DURING the past few years the writer has been impressed by the close relation of many epigenetic orebodies with anticlinal structures. In the literature on ore deposits there is occasional mention that an oreshoot or district is on an anticline, but in most of the descriptions no weight or significance is attached to the relation, and usually the fact is concealed in a mass of structural detail. A few writers have stressed the relationship in a few districts or on a certain type of deposit. Church, Spurr, Butler, Stahl and Schuette have called attention to certain features, but the general extent of such a correlation has not been made known in any publication that the author has seen. A recent article1 on the localization of ore deposits, by well-known geologists, does not consider this common association. The author has seen in the field a number of the structural features described, and in addition has made a fairly complete review of the literature. This paper presents enough of the examples found to show the frequency of the relation to anticlines, and since only a few deposits on synclines are known, all of these of any importance of which the writer knows are mentioned. With certain qualifications which are discussed later, epigenetic ore deposits of replacement or vein type are mostly found where local upwarps of the earth's crust have taken place. Where formations antedating the ore deposits are present in the proper attitude to demonstrate vertical warping (i. e., more or less horizontal beds) the structural feature on which a mineral district, or mineralized area is located is almost always anticlinal, or domelike in nature. Some or even most of the ore deposits in a given district may be on the flanks of the upwarp, but few major districts are located definitely on downwarped areas. Synclinal basins within certain limits of size appear to be unfavorable to the type of fracturing that admits ore-bearing solutions.

Jan 1, 1931

Striving to do a better job of ad- ministering the letter and spirit of the Federal Coal Mine Health and Safety Act of 1969, the Interior Department recently invited criticism-and got it. The criticisms were voiced on July 1 and 2 at the first of a series of public meetings being held by the Office of Hearings and Appeals at the Department's behest. Later meetings, at which all interested parties are invited to comment, are to be announced in the press and the Federal Register. Persons wishing to participate in the meetings should contact the Director, Office of Hearings and Appeals, 1015 Wilson Blvd., Arlington, Va. 22203. At the first Hearing, USBM Director Elburt F. Osborn outlined the progress his agency has made to date in implementing the law on three fronts: enforcement, education and research. Since the Health and Safety Act became law on December 30. 1969, he said, the Bureau's force of inspectors has grown from a mere 300 to almost 1100, while mine inspections have increased from 10,265 in 1970 to 11,021 for the first six months of 1971. On the educational front. Osborn said, the Bureau now has some 60 instructors who have trained about 50,000 miners in safety procedures since March 30. 1971. Classes at the new Federal Mine Safety Academy for both government and industry personnel begin on September 1, 1971. he added. Health and safety re- search, meanwhile, has been allot- ted $20.1 million for the 1971 Fiscal Year. Of this, $8.1 million is assigned to the Bureau and $12.3 million to contracts with universities and private companies. Admittedly, Osborn said, the mine fatality rate is still unacceptable, hut it was lower in the first half of 1971 than ever before---0.73 per million man hours and 0.31 per million tons of coal.

Jan 1, 1971

By C. P. Williams

THE lead-bearing area of Missouri has been subdivided, geographically, into the Southeastern, the Central, and the Southwestern

Jan 1, 1877

By George R. Cowan

A number of studies hare been reported of the effects produced in metals subjected to deformation by shock waves with maximum pressures ranging from tens to hundreds of kilobars. On the basis of the equations for the flow of mass, momentum, and energy through a stationary shock front, the macroscopic stress-strain curve for the resulting shock deformation can be calculated within narrow limits from the experimentally determined Hugoniol curve. In relatively weak shocks which are preceded by an elastic wave, the stress rises above the clastic limit only as plastic deformation proceeds cold thus the shock has a long toe. In strong shocks that override the elastic wave a high stress is applied without prior plastic deformation. A more important effect of increasing the shock pressure is the generation of shear stresses, called supercrilical shear stresses, that exceed the strength of the perfect lattice. A change in the mechanism of deformation is expected to result from the onset of supercritical shear. The shock disordering of ordered Cu3Au in strong shocks appears to be an example of such a change. It is suggested that the formation of fine twins in copper and nickel and the formation of structures which enable visible twins to be formed in the rarefaction ware, observed in copper and presumably in disordered Cu3 Au, are related to the occurrence of supercritical shear in shock dcformation. In recent years several studies1,2 have been made of the changes in structural and mechanical properties of metals produced by the passage through the metals of strong shock-compression waves ranging from about 50 to 800 kbar pressure. Recent work involving dynamic measurements of the shock compression "Hugoniot" curves 3-8 of many metals has developed techniques and provided data required to obtain the shock pressure and the (transient! plastic deformation produced in the shock-conlpression experirnents.9 Shock deformation has been found to be much more effective than slow deformation in changing the mechanical properties of metals, when the two are compared on the basis of equal plasti strain, Holtzman and Cowan9 made quantitative estimates of the shearing stress occurring in a shock front in a metal by assuming that the shearing stress is similar to that occurring in a shock front in a viscous, heat-conducting fluid, with the addition of a yield stress. Taylor's solution9 for a weak shock was used to estimate pairs of values of shearing stress and thickness of the shock front obtained by assumed choices of the ratio of effective kinetic viscosity to thermal diffusivity. It was noted from these values that. unless the shock front is extremely thin. heat conduction has slight effect, and the shearing stress is nearly independent of the mechanism of deformation. This mechanism does, however, determine the thickness of the shock front and the rate of strain. Furthermore, since the maximum possible shearing stress occurring in shocks of moderate strength does not greatly exceed the shear stress occurring in conventional slow deformation, the mechanism of deformation is not expected to be qualitatively different. The greater effectiveness of shock deformation in changing the mechanical properties of metals can be attributed partly to the fact that dislocations, when driven by near-conventional stresses, cannot keep up with the shock front, thus necessitating a higher dislocation density than required for an equivalent slow strain. The fast uni-axial strain occurring in the thin shock front would also be expected to cause a larger number of dislocation intersections to occur. In the upper range of shock pressures that have been studied the estimated values of the shearing stress exceeded the estimated shear strength of a perfect crystal. Under these circumstances it is reasonable to expect that the mechanism of deformation might be considerably different from that involved in slow deformation. Except for the observation by smith1 of twins in shocked copper, the effects of shock waves on metals did not show any obvious or large changes in properties that would indicate the onset of a change in the mechanism of deformation. The recent investigation of the effect of shock waves on ordered and disordered specimens of Cu3Au by Beardmore, Holtzman, and ever" showed a spectacular decrease in the amount of long-range order retained by initially ordered Cu3Au when the shock pressure was raised from 290 to 370 kbar. Since Dr. Holtzman and I suspected that this behavior probably was due to the onset of a shearing stress in the shock front in Cu3Au which exceeded the limiting shear strength of the perfect crystal. it was considered appropriate to examine directly the shock-front equations for a solid. and to obtain a sound estimate of the shearing stress occurring in the front using equation of state data obtained from shock studies. In this paper an estimate is made of the

Jan 1, 1965

By F. Julius Fohs

WITH portions of two coal basins within its borders and a few scattered fields already developed, the question arises: What is the future of Ken-tucky as an oil-producing State? Is the long list of failures due to lack of 'commercial pools, or unintelligent prospecting? A study of its beds and irregularities of structure points not only to a large waste of development money on unpromising areas, but also to the presence of a few structures well worthy of development. The surface rocks of Kentucky show in succession more than 4,000 ft. of Paleozoic sediments and more than 2,000 ft. of Cretaceous, Tertiary, and more recent deposits. Folding and erosion have brought these beds to the surface, where they have been observed and studied: in detail by my associate, James H. Gardner, myself, and others. This has given opportunity to observe the beds offering suitable reservoirs and having the proper impermeable covering; also the mapping of outcrops and outcrop lines, taken in conjunction with available well records, indicates that certain areas are worth testing, and with even greater definiteness shows areas which should be excluded, as devoid of possibilities. West of the Tennessee River, Cretaceous, Tertiary, and Quaternary sediments occur so that all trace of ancient folding is obliterated, the sediments overlapping unconformably Mississippian rocks. This area embraces 2,000 square miles, or one-twentieth of the area of the State, the Paleozoic rocks covering the remainder. Since there is nothing upon which to base the location of tests for oil and gas in the Cretaceous-Tertiary beds of Kentucky, the Paleozoic area will be chiefly considered.

Jan 3, 1915

By A. L. Marshall, F. J. Norton

TO determine how rigorous a treatment was necessary completely to remove sorbed gases from molybdenum electrodes in vacuum tubes, the degassing process in high vacuum was studied in the temperature range 800° to 2300°C., and the gases analyzed. Some work was also done on the degassing of tungsten, nickel, and carbon. It was shown that the amount of gas is proportional to the mass of the sample and not to the surface area, indicating that the gas is distributed through the body of the metal. A study was made of the solubility of nitrogen in tungsten and molybdenum from 1200" to 2400" C., at equilibrium pressures from 0.01 to 760 millimeters.

Jan 1, 1933

An old philosopher once said, "God grant me the serenity to accept those things I cannot change, the courage to change those which I can, and the wisdom to know the difference." It is time to take stock of how the human race has progressed-whether the trend now points toward greater evils or finer things. It is time that we stop fooling ourselves and put into effect a program of "real" conservation. By this it is not meant that we limit our concept to planting new forests, preserving wild life or preventing soil erosion, but rather taking stock of the expectancy of our resources, expanding human resourcefulness and effecting careful utilization and replacing of, or producing substitutes for, material resources. Man is still dependent upon energy and matter in certain usable forms, despite the fact that energy is inherent in all matter. Until such progress is made that the energy contained in all matter can be controlled, man must continue to utilize the common fuels. Advancement of research in atomic energy has cast a gleam of hope for future use of the tremendous energy contained in the atom. Use of atomic power for industrial pursuits would open up limitless resources of power. This energy, of course, is a two-edged sword, since man's progress and his means of destruction have always evolved parallel to each other. Thus it is estab-

Jan 1, 1950

By E. E. McGinley, L. D. Woodworth

DURING the past several years has occurred what, in the light of future events, may aptly be called the rebirth of the acid Bessemer process. The increased attention given to the technical and metallurgical details involved in the production of Bessemer steels has been exceedingly fruitful, and indicates the value of further research and plant development. In times like these, when the steelmaking capacity of the country is operating at a maximum rate to supply materials for the national defense program, it behooves the Bessemer operator not only to strive to increase production but also to maintain a high standard of quality. The opportunity is ripe, it seems, to recapture fields of application once considered the birthright of Bessemer steels, but supplanted in recent years by open-hearth grades. This involves cooperation all along the line, from the blast-furnace operator to the metallurgical contact man and salesman. The metallurgist's part in this program involves the study of the many steelmaking variables and the measures necessary to ensure constancy in the finished product. It is equally important that the knowledge gained be disseminated widely to ensure the wise application of Bessemer steels in new fields. The merits of Bessemer steels for certain work are well understood. The combined properties of good weldability, machinability and stiffness are unique and fully explain the strong entrenchment of Bessemer steels in certain fields; e.g., skelp for small butt-weld conduit, screw steels machined in automatics, and certain tinplate applications. It is the purpose of this paper to review briefly the physical properties of Bessemer steels as contrasted with those of open-hearth steels, to discuss control measures now employed in the making of Bessemer steel, and to consider the advantages derived from the use of these control measures. PHYSICAL PROPERTIES OF BESSEMER VS. OPEN-HEARTH STEELS A number of Bessemer blows and open-hearth heats were tested for tensile strength, ductility and impact strength. The steels selected were confined to sections from ¾ to 1 ¼ -in. diameter, inclusive, and the carbon content covered was sufficient to yield parallel ranges in ultimate strength for the comparison. Other factors, such as the extent of deoxidation of the steel and variations in chemistry, were kept as comparable as possible. Machined test pieces of 0.505-in. diameter with an 8-in. gauge length were pulled. The data obtained are shown in Fig. 1, ultimate strength being plotted against carbon content. This graph shows that for equivalent carbon content Bessemer steel has on the average 15,000 lb. per sq. in. greater tensile strength and, conversely, for the same tensile strength Bessemer steel requires on the average 0.14 per cent less carbon. The average phosphorus content for the Bessemer steel was 0.090 per cent,

Jan 1, 1941

By Warren K. Kourt

Many important discoveries of mineral deposits have been made as a result of routine exploration for oil and gas. Through the presentation of three hypothetical case histories, including cost data, the author shows how mineral evaluation can be performed during routine petroleum drilling operations and how mining companies and oil companies or oil operators can cooperate in such endeavors.

Jan 1, 1972

By Frederick Prime

IN this supplementary list no titles to which an * is prefixed have been seen by the compiler; and he will be most thankful to have any omissions or inaccuracies in the list sent to him to be published as a second supplement in the next volume of the Transactions. The author is indebted to Messrs. Robert Clarke, of Cincinnati ; Thomas Macfarland, of Towanda; Professor F. W. Simouds, of Chapel Hill; and Professor J. J. Stevenson, of New York, for valuable assistance. CEDAR POINT IRON COMPANY, BALTIMORE, July 31st, 1880. ALABAMA. Geological Survey of Alabama. Report of Progress for 1877 and 1878 ; by Eugene A. Smith, State Geologist. Montgomery, 1879. 8vo., 139 pp., and 4 maps.

Jan 1, 1880

By G. D. Coe, R. G. Meara, O&apos

PRIor to the World War most of the barite used in the United States for manufacturing lithopone and barium chemicals was imported. Germany, by virtue of an abundance of high-grade ore and low labor costs, was in a position to dominate the world market. With the cessation of imports and with the war demand for barium chemicals, the barium chemical industry and the mining of barite became well established in the United States. This industry has continued to expand because of the increasing use of lithopone. In 1914 the sales of domestic crude barite was 52,919 tons and in 1934 it was 209,850 tons. Barite deposits of economic importance occur in at least 20 states, but the principal producers in 1934 were Missouri, Georgia, Tennessee, South Carolina, Virginia, California and Arizona. The main mining centers are located near the crude barite markets of the three principal marketing districts—the Pacific Coast, the Midwestern area, and the Eastern area. The Pacific Coast is supplied entirely by California, Nevada, and Arizona. The Midwestern area uses most of the Missouri crude and a small amount from the southern states. The eastern market is the chief competitive area. Practically all of the imported crude is marketed there; also the bulk of the southern crude and ground barite. In addition, this area absorbs a small part of the Missouri crude and 80 per cent of the ground barite. Besides the advantage of low delivered costs and purity of product, the imported barite has commanded a price differential because it is soft rather than hard, like many of the domestic ores. The inherent physical properties of the southern ores remain, but the purity can be controlled to a great extent by beneficiation. Simple washing or gravity concentration has sufficed in the past, but in many cases a more efficient process now becomes imperative to remove impurities not amenable to these methods. Certain deposits now being opened are of lower grade and require more precise milling conditions. In some ores, the kind of impurities has changed as the mining advanced.

Jan 1, 1938

E. G. WOODRUFF, Houston, Tex. (communication to the Secretary*). -Mr. Matteson has presented to us an idea worthy of our careful consideration. We have real troubles in the petroleum industry and as the supply of crude is exhausted our problems become more complicated and more numerous. Therefore, we who are engaged in field work are forced to consider all possible means which promise assistance in the location of prospective pools and the economic development of pools already located. In our country we are accustomed to turn to the. Government for relief in all our troubles. Do we want an Oil and Gas Bureau doctoring us? Will such a bureau do us practical good? The principal point Mr. Matteson suggests is that such a bureau should he authorized to receive and file all well logs. In analyzing such function, I am led to the following conclusions: If well logs are simply to be filed they would be useless. If they are to be filed and the files opened to the public, what benefit will be derived and can such action be taken justly? There is no doubt that if the record of all wells drilled in the United States were available the petroleum industry would be saved an immense amount of needless expense. Accumulating conditions would be better understood and prospecting more intelligently directed. Our other consideration is: can the oil companies be required to open well records to the public justly? I think all will agree that if any one should have the advantage of a well record it should be the company that drilled the well. If the oil companies are forced to file such record and open the files to the public, the company drilling the well cannot derive the exclusive benefit from the money expended. Would it be just for a small company to be compelled to reveal its records of a well it had recently completed, to its strong competitor who holds near or even adjacent leases? Would it have been just to the successful companies, in the Gulf Coast country to have been forced to display their hard-earned knowledge of 15 years to the host of younger competitors who have recently flocked to the Gulf Coast attracted by the success of those who have labored so long and learned of the conditions controlling the fields through the hazards of the industry.

Jan 10, 1917

By Noel F. Boyd

Coal can be liquefied and gasified by several methods, all of which are being investigated and evaluated because each has its own advantages and disadvantages in terms of capital costs, end-products, and extent of required gas clean-up. Since coal conversion requires coal preheating to some extent, all these schemes begin with a coal-preparation step in a pressurized and heated reactor vessel where, in most cases, some additive or catalyst is usually injected. Extracting hydrogenated fuels from coal is not really a new science. Many people still recall the old "coal oil" that fired the lamps of stoves of rural America until the 1920's; the coal oil was produced by a basic Fischer- Tropsch method which has since been further developed to synthesize liquid fuels in the form of 86 to 90-octane gasoline and diesel fuel.

Jan 9, 1974