Search Documents

By Jacob H. Masliyah

The dynamic simulation of a gravity separation vessel (a high throughput classifier) has been developed. The feed slurry was assumed to contain light (oil droplets) and heavy (mineral solids) particulates of various size. The feed slurry was characterized by the particle size distribution of both the light and the heavy particles. The equations describing the slip velocity for each specie and those defining the time variation of each specie concentration were solved implicitly using Runge-Kutta algorithm. The dynamic simulation was capable of predicting the movement of the froth layer and the density variation of the under- flow. Field data are in agreement with the simulation model and it is shown how this model could be used to develop a control strategy.

Jan 1, 1984

By R. F. Mehl, R. F. Bunshah

A fast amplifier technique has been developed for the measurement of the rate of propagation of martensite in an Fe-29.5 pct Ni alloy. The time of formation of one plate of martensite is 3x10 sec and the rate of propagation is 3300 ft per sec approximately. IT has been known for some time that the plate-like structural unit of martensite forms from austenite with great rapidity. Wiester1 and Hane-mann, Hofmann, and Wiester took motion-pictures of the transformation as it occurs in a 1.65 pct C steel; they demonstrated that a single plate formed fully in the time interval between successive frames, viz., 1/20 sec, thus setting an upper limit. Forster and Scheil,3 using an Fe-Ni alloy with 29 pct Ni, recorded the sonic characteristics of the process electrically, upon an oscillograph, setting the upper time limit at 0.002 sec. Forster and Scheil,~ measuring the change in electrical resistance in the same alloy upon a cardiograph, set a limit of 0.02 sec. Forster and Scheil5 later, employing the same alloy, improved their technique, reporting an upper limit of 7.10 sec. In studying signals of such short duration, it is an important question whether the frequency response of the electrical system used is high enough compared to frequency of the pulse measured, or, put differently, whether the system is able to reproduce without distortion the signal arising, in this case, from the formation of a single martensite plate. Forster and Scheil (referring only to their last paper) obtained signals of a frequency of 30 kilocycles (hereinafter kc); this was about the frequency response of the equipment used; thus, if the signal had a frequency higher than 30 kc, it would still appear as a signal of frequency 30 kc. All of these results thus provided upper limits only. Recent developments in electronics have made available equipment with very high frequency response, very high sweep-speeds, high gain, etc. The electrical characteristics of such equipment, used in the present study, are given in Table I. Such equipment offers obvious attraction in the study of the rate of propagation of a martensite structural unit—and perhaps of other structural alterations proceeding at a very high rate. This paper reports an attempt to develop a technique employing such equipment to measure the time of propagation of a martensite structural unit and the variation of this with temperature, with the mode of formation—athermal and isothermal—in both polycrystalline and single-crystal samples; and from such measurements to obtain the rate of propagation. As will be seen, the results obtained are useful theoretically. Materials All data presented here are for an Fe-Ni alloy of the following analysis: 29.5 pct Ni, 0.027 pct C, 0.135 pct Mn, 0.094 pct Si, balance Fe. There were several reasons for choosing this alloy: 1—it is substantially the one used by previous investigators; 2—it exhibits both the athermala and the isothermal' mode of formation of martensite, both studied in detail by Machlin and Cohen; 3—the subzero temperatures of transformation in this alloy are experimentally very convenient; 4—it exhibits the "burst phenomenon";" 5—the change in electrical resistance upon the formation of martensite, a decrease, is great, approximately 50 pct.' The polycrystalline specimens were in the form of wires of 0.025 in. diameter; the single crystals were 1x1/4x1/4 in. Experimental Methods Electrical Apparatus: Fig. 1 is a schematic drawing of the electrical circuit used. The principle used in these measurements is the same as that used by Forster and Scheil." A small direct current, about 1 to 2 amp, is passed through the sample. When a martensite plate forms, the resistance of the sample changes and a high frequency signal is generated. This signal is picked up by the probes attached to the sample, fed into the bank of amplifiers and thence to the vertical deflection plates of a cathode-ray oscilloscope. The signal itself triggers the oscilloscope trace which flashes across the tube face and is photographed by means of a 35 mm movie camera at the end of a light-tight hood. The camera has no shutter. As soon as the signal flashes

Jan 1, 1954

By L. E. Garner

Aggregate resources should be considered primary factors in urban development. Resource planning is essential because land values, previous construction, or zoning restrictions often preempt exploitation of aggregate deposits within an urban area. Sequential land use practices allow development of area prior to urban development population and aggregate consumption trends in Austin, TX, indicate that substantial quantities of reserves will be lost to future development. Aggregate materials are present in nearby areas. However, a comparison of transportation and reclamation costs indicates that reclaiming land after mineral extraction can be significantly cheaper than transporting materials longer distances.

Jan 1, 1982

By Lyndon L. Foley

The proper spacing of oil wells is a problem of vital importance to the oil industry. Conservation demands a maximum recovery, while economic considerations attach primary importance to profitable extraction of oil. Formulas have been evolved,1-4 which attempt to solve the spacing problem mathematically, using reservoir characteristics as factors. Comparisons have been made of fields producing from supposedly similar sands, which have been drilled to varying densitiesl5,6 and also of different leases in the same field. 5-8 Intermediate wells have been drilled in old, depleted fields to test the efficiency of drainage by the original operation.9-11 Intermediate wells have been drilled also to obtain cores of the depleted sand for analysis, from which to learn the degree of efficiency of extraction. The problem is being attacked by many students, and along several different lines. Unfortunately, the fields now depleted were produced generally without restriction, and conclusions drawn from them may not apply to fields operated under restricted production. Reservoir conditions in a restricted field, especially reservoir pressures and pressure gradients within the reservoir, are quite different from those in a field produced to capacity. Many people have held the idea that the closer the spacing, the greater the recovery. This general statement is not always true, as other factors than well spacing enter into the recovery problem. Cutler,5 who has been quoted frequently by advocates of close spacing, limited his conclusions to gas-drive fields, and to the particular fields and spac-ings that he investigated. Hill and Sutton7 analyzed four tracts in the Powell field; the tract most closely drilled had the third largest recovery per acre-foot, and the tract with the widest spacing had the second largest recovery per acre-foot. A search of the references to well spacing in the publications of the U. S. Bureau of Mines5,13-19 discloses repeated condemnations of the wastefulness of the practice of town-lot drilling.

Jan 1, 1938

R. W. NEWCOMB,* New York, N. Y. (written discussiont).-On page 1638 mention is made of a new -instrument with an exceptionally high resistance that has been developed by Charles Engelhard. All friction and wear of moving parts of the moving system has been elimi-nated by replacing the hardened steel pivots and jeweled bearings, commonly used on other instruments, by a double metallic filament, one at the top and One at the bottom, under slight tension. Any pos-sible distortion of the moving coil, because of tension, has been eliminated by introducing a solid spindle as the axis of the coil between the points on the coil where the metallic filament is attached. The filaments serve not only as a support for the moving coil; but also to lead in the current from the binding posts to the moving coil, and as a source of counter-torque; instruments so constructed, do not require leveling, and are mechanically very robust. The clock of the recorder serves only to drive the chart at its specified rate and -to operate a small contact-making device; i.e., there is no other mechanical load on the clockworks. The contact-making de-vice is so constructed that there is a quick-make, a quick-break, and a wiping effect while the contact is being made. Contact surfaces on this switch are of platinum platinum-iridium. The operation of this contact, which occurs once each minute, sends a current, from a 6-volt supply; through a solenoid magnet, which operates the depressor bar mechanism in the case of the single-record instrument; in the case of the multiple-record instrument, it operates the automatic switch and color-changing features, as well as the depressor bar.

Jan 12, 1919

By J. Kinkead, R. M. Sherman, E. M. Frizzel

A recent research study performed under US Bureau of Mines Contract No. J0199088 "Modular Irrigation Equipment for Reclaimed Strip Mined Lands" investigated the feasibility of irrigation as a reclamation tool in the arid and semi-arid regions of the Western United States. Review of mined land characteristics, evaluation of irrigation systems, and assistance from the mining industry resulted in the design of two strategies for the implementation of reclamation irrigation using solid set systems. It is not the intent of this paper to suggest the generalizations made on the basis of a six state area can extend to the design of an irrigation system for a specific mine site. The purpose is to present two irrigation strategies that may be implemented with solid set irrigation in this six state area. The reader should note that the following is the result of research and, therefore, original concepts were presented. The ultimate validity of these concepts will be determined by future field tests.

Jan 1, 1983

By J. C. Wynn

This paper outlines research conducted by the US Geological Survey on the geophysical signatures of chromite. Results of the chromite study highlight the importance of a laboratory research Phase (petrophysical and petrographic studies) at the beginning of work on a new commodity; a realistic ore deposition model to serve as a conceptual framework, and the necessity to continually test, refine, and modify it during the study; and indirect geologic/geochemical indicators, secondary associations, and the use of multiple physical properties. The keystone to the success of the study is frequent and substantive dialogue among geologists, geophysicists, and geochemists.

Jan 1, 1984

By E. A. von Hahn, T. R. lngraham

Cementation rates ulere studied by rotating an elec-tropolished or etched copper strip in aqueous solutions, of either perchloric acid or alkaline cyanide, containing silver ions. The rates of cementation were more rapid in acidic media than in cyanide media. In both, the rates varied with the rate of rotation of the copper strip. The deposits formed in the acidic solutions were finely divided, loosely adhering powders. Those formed in the cyanide solutions were dense and adherent. The presence of the deposits influenced the cementation rates. In the acidic solutions the rate was enhanced, possibly because of the increased cathodic area. In the alkaline solutions the rates were decreased in the presence of the deposits. This has been attributed to restricting the diffusion of the copper ion from the rnetal outward into the bulk of the solution. In an earlier paper1 the authors described a kinetic study of the cementation of palladium on copper in perchloric acid solutions. That work indicated that there were two stages in the palladium cementation process. The first, more rapid stage was consistent with rate control by the diffusion of Pd11 ions to the copper surface and/or by chemical reaction at the surface. The second stage was consistent with rate control by the diffusion of copper ions from the copper surface, through the deposit, out into the main body of solution. The effect of the type of deposit on the rate of cementation is of particular interest because it may be one of the primary features involved when large quantities of metal are to be cemented from solution. No substantial investigations of the effect seem to have been made. Accordingly, an extension of the previous work was arranged to study the cementation of silver on copper. This system was selected because of the convenience of the analytical methods, the previously established technology with copper, and the fact that the system could be studied in both acidic and alkaline media. By selecting perchloric acid and alkaline cyanide solutions as the media, it was hoped that some assessment might be made of the effects, on cementation, of having the silver ion present in a virtually uncomplexed state and in a highly complexed state. EXPERIMENTAL The cementation rates were studied, as previously described,' by rotating a copper strip (1.0 by 23.2 cm) clamped to the peripheral surface of a lucite cylinder. The solutions were kept at constant temperatures (±0.05°C) under an atmosphere of purified nitrogen, and samples were taken periodically for analysis. The initial solution volume was 1000 ml and the sample volume 5 ml. The initial silver(1) ion concentrations were made low (0.5 to 1.0 x 10-4 moles per liter) to minimize the influence of the cemented deposit on rates. The solutions were prepared by dilution of suitable aliquots of silver perchlorate and silver cyanide stock solutions. Both stock solutions were prepared from purified silver powder (Johnson, Matthey, and Mallory Ltd.) with redistilled deoxygenated water, and they were kept under an atmosphere of purified nitrogen. To prepare the stock solutions, weighed amounts of silver powder were dissolved with nitric acid. For the AgC104 stock solution the silver nitrate solution was evaporated twice to near dryness with perchloric acid and then made up to volume: For the NaAg(cN)2 stock solution, the silver ions were precipitated with sodium hydroxide solution. The precipitate was filtered, washed thoroughly with redistilled water, dissolved with 1.1 times the required stoichiometric amount of sodium cyanide solution, and made up to volume. The small amounts of free perchloric acid and sodium cyanide present in the stock solutions were disregarded in the preparation of the solutions. The copper strips were cut accurately from 0.025-in. sheet (American Metal Climax OFHC brand) and annealed for 1.5 hr at 470°C in a stream of nitrogen. Analyses of the solution samples for silver and copper were done with a Techtron Model AA-3 atomic absorption spectrophotometer. Calibration standards of the same composition as the experimental solutions were prepared and analyzed simultaneously with the samples. No difficulty was experienced in the analyses, and the reproducibility was within 1 to 2 pct in both alkaline cyanide and perchloric acid solutions.

Jan 1, 1968

Map

Jan 1, 1937

By N. S. Keith

Some time ago, a firm engaged largely in the manufacture of copper sulphate, applied to me for information as to the practicability of obtaining the copper from their mother liquors by means of electricity ; having reference, more especially, to obtaining the electric current from some magneto-electric or dynamo-electric machine. The mother liquors were the result of several solutions of commercial scrap copper, containing impurities, the quantity of which

Jan 1, 1879

By P. Bolsaitis, L. Skolnick

Vapor pressures of silver over ternary alloys of six different copper to gold ratios have been measured by means of the Knudsen effusion technique. The data obtained in the temperature range of 1330° to 1375° have been used to estimate the integral excess free energies of the ternary alloys and the activities of copper and gold. The results compare favorably to the predictions based on the electron cell model of alloys recently formulated by the authors. THE orifice effusion method for measuring vapor pressures of materials in condensed phases was first introduced by knudsen, and has since been used extensively for the determination of thermodynamic properties of condensed phases. The basis of the measurement is the effusion, through a small orifice, of vapor in equilibrium with a condensed phase. Assuming free molecular flow into high vacuum, the vapor pressure, P (in mm Hg), of the effusing species is calculated from the following equation:' where w (g) is the weight of effusing species lost during a run, t (sec) the time length of the run, A, (sq cm) the area of the effusion orifice, T ("K) the temperature at which the run is conducted, M the molecular weight of the effusing species, and k the Clausing factor, a constant that corrects for deviations from free molecular flow caused by the finite thickness of the orifice walls.17 The determination of partial and integral thermodynamic variables from vapor pressure data of ternary alloys is possible only if the vapor pressures of all but one component are negligible or can be esti-

Jan 1, 1969

OF no less importance nor less terrifying to consider than the marvelous effects of guns are those produced with fire by powder in underground mines. These are truly not only similar to fearful natural earthquakes, but it can perhaps be said that these made by art surpass the wrath of the earth with greater effect. For if the latter shakes it happens that it causes the things on the surface to shake and sometimes to fall into ruins, but the former not only shakes but always functions and destroys-surely a marvelous effect which is almost incomprehensible, and if experience did not demonstrate it, it could scarcely be believed. Who would say that the mountains, things of such great hardness, would yield to men, easily opening their bowels? Likewise, one who had not seen it would say that it was impossible for men to have a way of administering at will fearful and destructive thunderbolts which are of such a kind that, although men make them, they cannot protect themselves against them; indeed they cannot call themselves safe from the evilness of gunpowder even in mountains composed of very hard stones or in budded structures. For, as is seen, there is no seemingly impregnable fortress that does not yield when guns are brought near it. If it happens, indeed, that guns can- not be brought near to some place because of the harshness of the site,

Jan 1, 1942

By H. M. Chance

Stretching from New York southwestwardly to Georgia is a great range of hills and mountains consisting of pre-Palæozoic schists, slates, .and gneissic and granitoid rocks, known locally by many different names; in Pennsylvania as the South mountains, the Berkshire or Durham and Reading hills, and in Virginia and farther south as the Blue ridge. To the northwest of this range lies the " Great Valley," underlain by Lower Silurian limestones, and known as the Lehigh valley, Cumberland valley, Shenandoah valley, valley of Eastern Tennessee and Georgia and by other local names, but all these are parts of one valley, geologically and geographically continuous from New Jersey to Georgia. Lying upon and along the northern flank of this range of mountains, and dipping northwestwardly under the limestone of the valley, is the Potsdam formation (Primal or No. 1 of the Pennsylvania Geological Survey), which consists of sandstone or conglomerate overlain by slates. The latter are sometimes arenaceous and occasionally are replaced in part by sandstone. This formation varies from a few feet to several hundred feet in thickness. At the outcrop the slates are completely decomposed, oxidized or disintegrated, forming a belt of clay several hundred feet wide occupying the interval between the outcroppings of the sandstone and limestone. This clay-belt includes a more or less continuous series of iron-ore (brown hematite) deposite, which have been, and still are, extensively worked. The belt is more or less continuously milleralized with iron throughout its length, and hundreds of large deposits of ore have been developed and worked, producing many millions of tons of ore.

Jan 1, 1909

By Walter R. Hibbard, Harold Margolin

DURING preliminary tests on the aging of a Cu-plus 5 pct Ag alloy,' a specimen which had been overaged 24 hr at 550°C was annealed in a nitrogen-hydrogen atmosphere first for 2 hr and then for an additional 28 hr at 600°C. After each anneal the specimen was cooled to room temperature in about ½ hr and X-ray photograms were made. The first film, Fig. la, revealed two sets of copper-base lines, one intense and corresponding to the parameter at 550°C, the other fainter and shifted away from the beam, corresponding to the larger parameter at 600°C (see arrows). The 30-hr film, Fig. lb, revealed the same two sets of copper-base lines with a reversal of intensity. In neither case do the copper lines form a broad band which would be indicative of a range of compositions. This phenomenon is thus a "discontinuous" type of solution. A similar phenomenon was observed in a Ag-rich Cu-Ag alloy.' Finlay and Hibbard9 have suggested that directional rather than random solution of precipitate occurs in some alloys. Conceivably, for Cu-Ag alloys, the matrix-transition-precipitate precipitation sequence is reversible for the re-solution of the precipitate caused by rapidly raising the annealing temperature of an overaged specimen. A copper-base transition structure supersaturated with solute might be formed around the precipitate as it dissolves, thus obviating the necessity for a gradually changing solute composition of the matrix. The solute atoms then might be transferred rapidly and locally from the transition to the matrix phase in the proper amount and at the proper location to obtain directly the new ex- panded solid solution. The theory implies a minimum of diEusion of solute in the matrix (i.e., no significant range of matrix composition) and possibly suggests that the composition of the transition structure will vary with the conditions of re-solution. A transition copper phase found in aged Cu-Ag alloys1 might fulfill this function. Evidence regarding this suggestion could be obtained in Cu-Ag alloys by overaging a specimen until no trace of the expanded copper lattice is present and then subjecting the specimen to a retrogression treatment. Re-appearance of the transition copper phase would confirm the theory. Additional details could be secured by varying both aging and retrogression temperatures. References 'H. Margolin and W. R. Hibbard, Jr.: Effect of Ternary Additions on the Age Hardening of a Copper-Silver Alloy. Trans. AIME (1951) 191, p. 174; Journal of Metals (Feb. 1951) TP 3002E. 2 W. Ageew, M. Hansen, and G. Sachs: Decomposition and Changes in Properties of Super-saturated Silver-Copper Alloys. Ztsch. Physik (1930) 66, p. 350. 3W. L. Finlay and W. R. Hibbard, Jr.: Some Effects of Applied Stresses on Precipitation Phenomena. Trans. AIME (1949) 180, p. 255; Metals Technology (Sept.

Jan 1, 1952

By C. M. Young

THIS is an attempt to bring together some of the knowledge of the .coal-forming conditions obtaining during the Pennsylvanian period in the Western Interior Coal Province, to sketch briefly the present extent and character of the coals produced, and to show the beginning of cor-relation of beds over wide areas. Coals of later age than the Pennsyl-vanian are not included and, for reasons that will appear later, little attempt is made to cover the districts of eastern Oklahoma and western Arkansas, and northern Texas is omitted entirely. GEOLOGICAL CONDITIONS The conditions that made possible the formation of large coal beds in the United States were most favorable in the Pennsylvanian period, formerly known as the Upper Carboniferous. The geological conditions can be determined from the records, but not the reasons for them. Preceding the Pennsylvanian was the Mississippian, formerly known as the lower Carboniferous and still later as the sub-Carboniferous. Dur-ing this time, large bodies of limestone were deposited and at the close f the Mississippian they were warped upward and for along period were eroded. Then there began a period of subsidence, more or less inter-rupted at times, during which the Pennsylvanian strata were deposited (see table on page 2). " These consist of sandstones, limestones and shales, with occasional coal beds: At the beginning of the Pennsylvanian there was subsidence, which allowed the sea to extend over the eroded Mississippian surface to the north and east, extending over eastern and central Texas, a large part of Oklahoma, with a projection into Arkansas, over Kansas and part of Nebraska, all the northern and western part of Missouri, a large part of Iowa except a strip in the north, most of Illinois, practically all of Ken-tucky, northern Tennessee, most of Indiana, all of the eastern part of Ohio, practically all of West Virginia, western Maryland, the west end of Virginia, and a large part of Pennsylvania. The Ozarks were already

Jan 1, 1935

By John L. P. Campbell, Warren J. Jackson

Automatic recording of the radioactivity of the earth's formations provides a log of relative intensities that, if properly interpreted, can be applied to oil-field engineering. Production, engineering, and geological departments regard the radioactivity log as a forward step in the securing of more conclusive information for successful well completions. Explanations of the technique, together with some of the problems to which radioactivity logging have been applied, are presented in this paper. Introduction Those responsible for the completion of new oil and gas wells, or with planning workover operations on old wells, have followed closely the development of radioactivity well logging because they are interested in reducing the number of unknowns that usually are present in such work. Many operators have made use of the log, or are acquainted with at least one of the applications, but it is unlikely that any one operator is familiar with all of the many applications that are possible. The purpose of this paper is to present a representative example of each of the many applications, wherever the information has been released by an operator, and to illustrate by hypothetical examples other applications, releases for which have not been given. In this way, it is hoped that a better understanding of the scope of this new engineering tool may be obtained. Athough the literature contains many references that describe in detail the theory, development, and application of radioactivity well logging, a brief discussion of the technique may be helpful to those who are investigating the subject for the first time, All rocks contain radioactive material in varying concentrations. In general, shales contain relatively more radioactive material than sandstones or limestones. These radioactive materials disintegrate with time into other materials of lower atomic weight, and in that process of disintegration the rocks are emitting many rays, the most penetrating of which is the gamma ray. The intensity of emission of the gamma ray is proportional to the quantities of radioactive materials present. A higher rate of emission would be observed, therefore, opposite a shale than opposite a sandstone or limestone. Since measurable intensities of gamma rays are capable of penetrating as many as five concentric strings of casing, and as the gamma-ray intensity is relative to the formations, the measurements of variations in gamma-ray intensities offer a means of identifying cased-off formations in their proper stratigraphic sequence. TEe Gamma-ray Curve The measurement of gamma-ray intensi ties is accomplished by means of an ioniza-tion chamber that consists of a heavy cylinder, about 3 ft. long, that contains two insulated electrodes and is Med with an inert gas under high pressure. Under normal conditions no current will flow through the gas when an electrical potential is set up between the electrodes, but when

Jan 1, 1946

By J. C. Bayles

It is seldom the privilege of one who contributes to the Transactions of a technical society, to describe a new industry in which, by processes employed for the first time, are attained results of conspicuous value. There are but few such patches of virgin soil worth the tilling, within the area circumscribed by the industries which have experienced a regular and uniform development. New and startling methods in production are often announced as about to be introduced; but, as a rule, they take their place among the " large desires with most uncertain issues," or give new significance to the historic words of an eminent statesman concerning " the bright beginnings and the bitter end of a halcyon and vociferous proceeding." In this paper I shall have the pleasure of briefly describing a new industry which has been established without announcement or proclamation — the manufacture of serviceable pressure pipes of great strength, from strips of steel or iron wound spirally, heated only along the overlapping edges, welded by hammering and finished into tubes of uniform diameter, and of such length as mag be found convenient in handling and transportation. As such tubes are now manufactured on a considerable scale, in a range of sizes which will soon include everything between 4 inches and 30 inches, and as much larger as may be needed, both process and product are likely to be of interest to engineers in all departments of professional work. The raw material of the industry is the ordinary sheet-iron or steel of commerce, of such lengths and widths as it is convenient to roll. The range of the ganges of the metal which can be employed has riot yet been determined. The lightest metal thus far successfully made into pipe is No. 29 iron, and the heaviest a steel gauging somewhere between 12 and 14. Heavier machines are now building which will bend steel .165 of an inch in thickness, or No. 8 of' the Birmingham gauge. Probably No. 20 or No. 22 will be the lightest used in making commercial pipes; hut the experiment with No. 29 was interesting as showing the readiness with which the flame can be controlled. To get a welding heat with such thin

Jan 1, 1888

By E. M. Wise

THE properties required of gold alloys for jewelry are not well standardized, due in part to problems peculiar to certain branches of the jewelry industry, in part to the individual preference of the fabricator and to his willingness to cope with certain difficulties in manufacture, which arise with the use of certain alloys. GENERAL REQUIREMENTS In general, the properties desired may be classed as follows: 1. Color should conform to the dictates of good taste and smart style. 2. Corrosion resistance and tarnish resistance should be good. This is to a considerable extent determined by the carat. Resistance to such corrosive agents as mercuric chloride as well as certain depilatories is unreasonable to expect and difficult to meet. 3. Strength and hardness must be adequate to maintain the delicate contours of finely modeled jewelry. 4. Wear resistance must be great enough to resist abnormal wear, such as is encountered by a wedding ring in a lifetime of wear. 5. Ductility must be sufficient to permit the fabrication of drawn shells, tubes and difficult shapes. Material having a yield point of not less than 60,000 lb. per sq. in., an ultimate strength of 100,000 lb. per sq. in., and an elongation of 40 per cent. is desirable. 6. Melting point should be between 800° and 1200° C.

Jan 1, 1928

Jan 1, 1942

By C. K. Leith

ManGanese is one of the minerals which is principally consumed in countries other than origin. Nearly 85 per cent. of the world's production is used by the United States, England, Germany and France, and roughly a third of the total is used by the United States alone. On the other hand, over 85 per cent. of the world production comes from Brazil, Russia, India, the Gold Coast of Africa and the Sinai Peninsula. It follows from this fact that practically all manganese moves across international boundaries in raw or alloy form, and much the larger part of this inovement is for considerable distances and is occan bornc. There is no indication that any one of the principal consuming countries can develop even approximately adequate supplies of its own. Under abnormal war conditions, with high prices and changes in metallurgical methods, only 35 per cent. of the needs of the United States was met from local sources, and under our recent tariff only 11 per cent. There are thousands of manganese deposits scattered about the world, but only a very few which can figure largely in supplying requirements on a modern scale. The known reserves, together with highly probable extensions and explorations now under way, indicate no shortage from a world standpoint for many deeades to come. The production and marketing of manganese is going steadily into fewer and stronger hands. The steel industry uses over 90 per cent. of all the manganese mined and is acquiring control of a considerable part of the production in all of the principal fields—the Germans in Nikopol, the English in India and Gold Coast, the Americans in Georgia, India, Gold Coast and Brazil. Some of the controlling companies arc of international scope. Concentration of commercial control is a notable tendency. A natural consequence is the growing uneasiness of smaller consumers the world over about their ultimate supplies and desire to know more definitely how and where manganese supplies will be controlled in the future. The sources of supply are few cnough to warrant the belief that more or less monopolistic elements of control arc not impossible.

Jan 1, 1927