Search Documents

By J. L. Huitt, J. L. Pekarek, D. K. Lowe

In a theoretical study of hydraulic jetting, the velocity of the abrasive material relative to the velocity of the fluid in the jet stream is analyzed as the jet stream moves through the convergent and straight sections of the nozzle and the region between the nozzle exit and target. The results revealed that the abrasive material exits from the jet nozzle at a lower velocity than the fluid. The exit pmticle velocity can be increased by increasing either the density of the fluid or the length of the nozzle, and/ or decreasing either the particle density or particle diameter. In the divergent jet stream, there exists a point after which the particle velocity exceeds that of the fluid. The relative velocities were considered in the derivation of an equation to predict cutting rate of a circumferential notch and maximum notch depth. Data of a general nature and data which substantiate the theoretical results were obtained experimentally. INTRODUCTION The use of a fluid containing an abrasive material has been an established technique for cleaning and cutting for many years. In the petroleum industry, the early effort to use this technique1 to perforate and/or to overcome wellbore damage met with only limited acceptance because of the short life of the jet nozzle. With the introduction of improved perforating techniques, and later, hydraulic fracturing, the use of hydraulic jetting as a well completion technique became even less appreciated. It was only in recent years that interest in hydraulic jetting was revived. Once this interest was revived, the results of surface tests stimulated the interest of the industry even more than the state of the technology probably warranted because many of the tests were not appropriate for down-hole conditions. However, because of the stimulated interest, the development of the jet nozzle progressed very rapidly to the point where the nozzle life was no longer a prob- lem. With this accomplished, the use of hydraulic jetting in well completion became an accepted practice in a short time. The purpose of this paper is to present a theoretical analysis of the hydraulic jet stream as it passes through the nozzle and travels to its target. With a better understanding of the jet stream and the effects of various parameters, the performance of the process can be predicted more accurately. Equations are presented for cutting rate as applied to circumferential wellbore notching that relate the jet stream make-up, notch configuration and formation material. Also, experimental data are presented on some factors pertinent to hydraulic notching that are not theoretically analyzed. RELATED STUDIES Most of the studiesl-5 reported in the recent literature have pertained to the more practical aspects of hydraulic jetting; i.e., the effects of certain parameters as interpreted from experimental results, and the application of hydraulic jetting in well completion. In reviewing the effects of various parameters, it is interesting to note the reported depths of penetration obtained under various imposed conditions. In general, the depths vary from a few inches to several feet; however, a depth of penetration of less than 6 in., as reported by Thompson,4 seems more realistic for the usual field practice of hydraulic jetting with sand in water for a period of 20 to 30 minutes. In addition to the practical aspects, the study of Brown and Loper5 included a theoretical approach to hydraulic jetting. Their study resulted in the development of a theoretical expression for the maximum depth of penetration if jetting were continued for an infinite time. An analysis of the equations presented reveals that the initial cutting rate is infinite. The equation expressing centerline velocity is that of Forstall and Gaylord,6 which is applicable for a jet stream exiting in a large stationary medium. Since practically all of the fluid pumped into a perforation (or cut) must flow back through the perforation prior to re-entering the wellbore, a description of the medium as finite and non-stationary seems more reasonable. Thus, in this

By W. Luyken

A NUMBER of articles have been published, notably those by R. S. Handy, R. T. Hancock and A. P. Watt in Engineering and Mining Journal, dealing with the calculations involved in ore dressing.. These publications demonstrate both, the importance of the subject and the lack of success in developing a generally recognized method for comparing enrichment effects. Considering that we may wish -to compare enrichment results on similar or dissimilar ores, that we may desire to make the comparison on the basis of either the absolute or the economical efficiency, and that the number of factors upon which the result depends is large, the question arises whether it is possible to set up a positive method for such calculations. In the following pages it is our aim to show that a sure, complete and successful way to overcome existing difficulties has been found. GRAPHICAL ANALYSIS OF ORE-DRESSING PROCESSES The following is from Truscott's Text Book of Ore Dressing (London, 1923) x = assay of ore treated (feed). y = assay value of the concentrate. z = assay value of the tailing. a = weight of feed. b = weight of concentrate. c = weight of tailing. C = fractional concentration = b/a= x-z/y-z (1) K = ratio of concentration = 1/C = a/b =y-z/x-z (2) R = fractional recovery = yb/xa = Cy/x. (3) 100R = percentage recovery. Copt = theoretically best concentration. 100 - Copt = waste in the feed.

Jan 1, 1929

By E. Stamboliadis

Dithiophosphates are reaction products of phosphorous pentasulfide with various organic compounds such as phenols, alcohols, mercaptans, dioalcohols, amines, and nitrides. The products with alcohols are commercially known as "aerofloats" and these are investigated in this presentation. It appears that the formation of insoluble metal dithio phosphates is responsible for their collecting properties with minerals." In this aspect they are very similar to xanthates.3 The solubility of metal dithiophosphates depends on the number of carbon atoms in the organic chain of the corresponding alcohol. An empirical mathematical model is presented here. It allows one to predict the number of carbon atoms necessary to ensure that a certain metal dithiophosphate will form at a selected pH value of the water solution. The Nature of Dithiophosphates Dithiophosphoric acid is the product of the reaction of phosphorus pentasulfide with an alcohol, as shown in the following equation: [P2S3 + 4 ROH - 2 (RO)2 PS2H + H2S (1)] where R stands for a hydrocarbon chain. The acid so produced can be neutralized by a base to produce the corresponding salt as shown in the following: [(RO), PS2H + NH- (RO)2 PS, NH,. (2)] In this aspect dithiophosphates are similar to xanthates, the only difference being the substitution of the tetravalent carbon atom in the xanthate polar group by a pentavalent phosphorus atom in the dithiophosphate group. This difference implies at least two characteristics: (1) that there are two hydrocarbon chains associated with the polar group so that an increase in the number of carbons of the single chain is expected to have a pronounced effect on the flotation properties, and (2) that the bond between the sulfur and the central atom is stronger than in the xanthate group. This probably leads to a decrease in both the polarizability of the electronic cloud of the sulfur and the interaction with cations.3 However, what is lost in the dithiophosphates by having a weak polar group can be gained by an increase in the number of carbons as will be seen later. Taking into account the size of the atoms involved in a dithiophosphate molecule, as listed in Table 1, It is possible to draw an approximate diagram of its structure as shown in [Fig. 1]. It is assumed here that the length of the single hydrocarbon chain is equal to that of the corresponding alcohol. Preparation and Purification Acid dithiophosphates can be prepared, as previously mentioned, in accordance with Eq. 1. The rate of this reaction is too slow at room temperature and can be improved by increasing the temperature to about 60° or 80°C7 or by evacuating the system. In our investigation evacuation was performed by a water aspiration pump. The dithiophosphoric acid so produced is liquid and dissolves in the alcohol. At the end of the reaction the product is filtered from the remaining P2S3; and dissolved in petroleum ether. By blowing anhydrous ammonia gas into the ether phase the ammonium salt forms as a white precipitate and can be sepa-

Jan 1, 1977

By C. R. Kuzell

INTRODUCTION KNOWLEDGE of the thermal capacity of gases is of great importance in making metallurgical calculations. The metallurgist is, frequently called upon to investigate and determine furnace efficiencies in which the heat carried into or out of the furnace by gases is a large item in the heat balance. Not only do such problems present themselves in the determination of furnace efficiency, but also in the study of the application of heat is accessory apparatus, such as stoves, regenerators, waste-heat boilers, driers,.etc. The thermal effect of the use of excess air in the combustion of fuel, the theoretical temperatures of combustion, the quantity of heat in hot blast at various temperatures, the effect of hot blast on furnace temperatures, are a few more examples of frequently occurring calorific problems involving gases. So many are the applications of the data on the heat capacity of gases that the subject merits careful study. The heat in a gas maybe due to its heat of combustion, if it is a combustible gas, and to its temperature. The latter is called its sensible heat and is the heat absorbed or evolved by a gas as its temperature is raised or lowered. The heat of combustion of gases is well established and is commonly known. The values can be found in almost any mcdern treatise on metallurgy. The sensible heat of gases has not been so well established because it is in most cases a function of the temperature, and the values of specific heats of gases over a wide range of temperatures have only recently been determined. It is the purpose of this paper to deal with the sensible heat of gases.

Jan 8, 1914

By Reginald S. Dean

THE commercial availability of electrolytic manganese has greatly changed the position of manganese as a nonferrous alloying metal. Manganese metal commercially available up to about ten years ago was reduced with either silicon or aluminum and contained substantial amounts of the oxides of these metals and other impurities. Manganese was accordingly not available as an alloy base and its addition to copper-base and nickel-base alloys was generally limited to a manganese content of a few per cent. Several special alloys like manganin contained up to 12 pct of manganese. A method for the production of electrolytic manganese was developed by the Bureau of Mines in 1936 and commercial production was begun in 1938. At the present time (June 1951), production is about 12 tons per day but appears likely to be substantially increased. Electrolytic manganese is deposited from an aqueous electrolyte containing manganese and ammonium sulphates and is marketed as cathode fragments about 1/8 in. thick. The impurities in its composition are as follows: iron, 0.0015 pct; copper, 0.001; arsenic, 0.0005; cobalt, 0.0025; lead, 0.0025; molybdenum, 0.001; sulfide sulfur, 0.017; sulfate sulfur, 0.014; insoluble, 0.002; carbon, 0.002; hydrogen, 0.015. These figures are from Bulletin 463, U. S. Bureau of Mines. From an alloying standpoint, the most important impurity is hydrogen. This can be removed by heating; 95 pct of the hydrogen can be removed in this way without introducing significant amounts of oxygen or nitrogen. Much of the commercial electrolytic manganese used in alloys is dehydrogenited by the producer, since the amount

Jan 1, 1953

By D. Turnbull, J. C. Fisher

ACCORDING to the "reaction-path" modell,2 of martensite nucleation, the shear angle of the embryonic martensite plate must be treated as a variable, and included in any calculation of nucleus critical size. Also, as can be deduced from this model, the interfacial free energy between austenite and martensite does not reach its final value until the shear is completed. It is zero for zero shear angle. However, in order to account for the kinetics of the martensite transformation, some sort of interfacial energy barrier appears to be necessary even with the reaction-path model, for otherwise the volume and the energy of formation of the critical size nucleus both collapse to zero.3 Cohen independently suggested that surface energy could be incorporated into the reaction-path model, with the overall free energy of a martensite embryo being a function of its volume and shear angle.' It is possible to estimate the energy associated with the formation of a critical-size martensite nucleus starting with the reaction-path model and including a surface free-energy barrier. As the dependence of interfacial free energy upon shear angle is unknown, a simple type of dependence will be assumed, with the belief that the true dependence would not lead to appreciably different results. Consider the work required to form a lenticular martensite plate with radius r, thickness t, and shear angle 8. There are three contributions; one being the interfacial free energy, one being the free energy change in the martensite plate, and one being the free energy increase in the surrounding austenite. The interfacial free energy u is assumed to depend upon the shear angle 0 according to the relationship s=s0(?/?0)n [1] where 8, is the equilibrium shear angle and n is an exponent that may lie in the range 0 n 2. The work required to form the interfaces of a martensite plate then is W. = 2pr² s0(?/?0)n [2] The free energy change per unit volume of martensite is composed of two parts, one the ordinary volume free energy ?f1. which is negative, and the other the elastic strain energy G?m²/2, where G is the shear modulus and 7, the shear strain relative to the martensite structure. This expression for the strain energy is valid only when the shear strain ym, is sufficiently small that the martensite is within its linear elastic range. There is no doubt that ym, lies beyond the linear elastic range for embryos that are considerably subcritical. However, for critical nuclei it will be shown that ym, is 1.5 pct or less, within the linear elastic range of martensite. For embryos of nearly critical size, then, the strain energy of the martensite is correctly given by G?m²/2. The shear strain in the martensite is ym, = 8, — 8, and the work required to form the strained martensite is Wm --= (pr²t/2) [?fv + G(?O - ?)²/2] [3] The free energy change in the austenite is entirely that due to elastic distortion. The elastic strain is not uniformly distributed in the austenite, being large near the martensite plate and small elsewhere. Approximately, however, the energy corresponds to a uniform shear strain ya= (?t/2)/r [4] throughout the volume 4pr³/3 surrounding the plate. The work required to strain the surrounding austenite then is Wa = (4pr³/3) (G?a²/2) = (G?²/6) prt² [51 For simplicity, the same shear modulus G is assumed for each structure. The total free energy for forming a plate then is W = W3 + Wm + Wa. = 2pr² s0 (?/p?0)n + (pr²t/2) [?fr+G(?0-?)²/2] + (G?²6) prt2 [6] This expression is correct for nuclei and for embryos of nearly critical size, where, as will be shown, the strain energy in the martensite is correctly given by the expression G (? — ?)². Having W as a function of r, t, and 8, as in Eq. 6, there is a saddle-point where W has a stationary value, W subsequently decreasing indefinitely as the nucleus volume increases along the reaction path. The stationary value of W is the energy of the critical nucleus. The critical nucleus has radius, thickness, and shear angle such that ?W/?r - awlat: = ?W/?p? = 0. Performing these differentiations and calculating the critical nucleus energy, W* = [8192p(G?/6)²;s/27 ?fv4] [7] where a= (?/?0)3n+1[l +G(8"-8)'/2af.]' [7a] and where 8 is to be determined from the equation (1 + 3n/4) + G8(6O - (9)/[Af. +G(6>o-6>)72] = 0 [8] For ?f, near —200 cal per mol or —10" ergs per cc, and 8, near 1/6, as for iron-base alloys, Eq. 8 gives ?0 - ? ~ - (4 + 3n) ?f1./4G0O [9] as the difference between the equilibrium shear angle and the actual shear angle for a critical nu-

Jan 1, 1954

By Waldemar Lindgren

CONTENTS. [ ] I.-CHARACTER OF THE DEPOSITS. 1. Principal Features. IN many schemes of classification and description the term contact-deposit has been somewhat loosely applied to all accumulations of useful minerals (other than those of unquestioned sedimentary origin) which are enclosed between two different rocks. As thus used, the term may include deposits of widely differing origin, and, unless qualified, is not in place in a genetic classification. The present paper deals with a special class of contact-deposits. In many geological provinces, granular igneous rocks, such as granite, diorite and syenite, have broken through and invaded sedimentary rocks. The molten magma may in part have reached the surface and there solidified with relative rapidity as a lava. The largest masses of it, however, did not reach the surface, but cooled very slowly at considerable depth under great pressure, and eventually consolidated into a rock of granitic texture. Uplifts and extensive erosion may have followed; and at the present day, in many places, thousands of feet of material have been removed, bringing to the surface the intrusive granular rocks and their once deep-seated contacts with the sedimentaries which they shattered at the time of in-

Jan 1, 1902

By E. S. Machlin

RECENTLY, there has been much activity in the field of nucleation of martensitic transformations.'- One of the problems in this field is the calculation of the rate of nucleation (number of plates nucleated per unit untransformed volume per unit time) in terms of observable parameters. Two such observable parameters are the fraction of the length of a straight line which corresponds to the portion of the total length of the line that lies in the martensitic phase and the number of plates intersected by this straight line per unit length of line. Because of the necessity of a valid answer to this problem, the following investigation was undertaken. Although this problem has been treated in the past, a derivation of the relation between the volume and linear fractions of martensite will be described to illustrate the method used in the succeeding analyses. It is assumed that the martensitic plates are in the form of a right circular cylinder having a small height relative to the radius of the base. The volume fraction of martensite is then: fr = lXNl,hjAl [1] where f, is the volume fraction of martensite, and Nij is the number of plates per unit total volume having the area Ai and the height hi. The linear fraction of martensite is obtained as follows. For the plates having the particular area A, and height h,, the fraction sin 0 dB* will have their cylinder axes between the angles 0 and 0 + d0 to the straight line along which the linear fraction of mar-

Jan 1, 1953

By J. M. Hartman

ONE of the most important subjects to the blast-furnace engineer is a thorough knowledge of the conditions affecting the temperature in the different portions of the furnace. All efforts to decrease the consumption of fuel and improve the working of the furnace must be based upon it, and I may, therefore, be permitted to place before you the results of my observations, and detail the conclusions to which they have led me. Tracing the thermic conditions from below upwards we have at the bottom of a blast furnace making No. 3 iron a temperature of 2900° F., which increases slightly to a point a little below the tuyeres. In the immediate vicinity of the tuyeres the temperature is somewhat lower, owing to the entering blast ; but a short distance above the tuyeres, where all the oxygen of the blast has been converted into carbonic acid, the highest temperature in the furnace must be attained. This carbonic acid is, however, almost as soon as formed, converted by the glowing coal into carbonic oxide, a process which absorbs heat, reduces the temperature, and provides the active agent for the reduction of the iron ores. In its ascent the hot carbonic oxide gradually parts with its heat, first melting the descending iron and earthy materials, which drop down to the hearth of the furnace. The limit of this zone of fusion is rather sharply defined, and the temperature above this zone suddenly decreases. In its further ascent the hot gas drives off the carbonic acid from the limestone, which causes a further absorption of heat, and finally the gas escapes at the top, at a temperature of about 250° F. if the furnace is working well. These changes of temperature 1 have attempted to represent graphically,

Jan 1, 1880

By B. Fernow

(Read at the Philadelphia Meeting, February, 1878.) THE question of preserving the forests in this country is an important one, not only to trades using wood but to the whole nation, and though agitated for many years has not received that general consideration which its broad bearing demands. Those who are interested in and working for reform in the treatment of American forests are looking to the government for help, suggesting the creation of a commission to study the conditions of forests at home and abroad, and hope that a sound system of managing the woodlands will be thereby inaugurated. This reform will cost time and money, all the more because the government can bring to bear upon private owners hardly any power but that of good example and encouragement. There is, however, another aspect of the question to which I wish to draw your attention, namely; the more economical use of the valuable material which our forests offer, a more careful and exhaustive utilization of its constituents in all cases where wood or its products are applied. The wasteful consumption of wood in the United States is in every way so enormous as to justify the statement that by merely adopting an economical husbandry in this particular the destruction of forests might be delayed for many years, while the neglect of this imperatively needed and immediately practicable reform deprives legislative remedies of much of their value. In this regard I wish to draw the attention of metallurgists, especially those who are interested in the manufacture of charcoal iron, to a more economical and profitable use of wood in iron manufacture. For thousands of years of human history wood was the main, nay, the only material used for fuel. Mineral coal came into use only in the fourteenth century, and it is only recently that it has largely displaced its less carbonaceous predecessor as fuel. The art of concentrating carbon in the form of charcoal for easier transportation and readier use in distant places was, according to Pliny, known to the ancients long before Christ, and was practiced in all countries, especially in connection with the iron- manufacture.

Jan 1, 1878

By J. H. Hamilton, J. R. Lewis, J. C. Nixon, C. L. Graverson

Recently there has been much speculation concerning the advantages of using oxygen enriched air or pure oxygen in pyrometallurgical processes. The advantage of using oxygen in the iron blast furnace and elsewhere in ferrous production metallurgy has been given careful consideration and, as a result, several experiments have been tried and a number of papers have recently appeared on this subject.1,2 The use of oxygen in nonferrous smelting likewise poses interesting problems, therefore any experimental data obtained in this area should likewise be of general interest.3 Ashcroft4 in 1933 claimed to have obtained improved results when copper concentrates were roasted in pure oxygen. However, his paper gives neither data nor experimental details. A few years ago a research program was started in this laboratory which had for its objective the determination of the mechanism of oxidation of metallic sulphides under varying conditions. To date we have studied the oxidation of galena,5 sphalerite, and chalcocite. It is a well known fact that copper sul-phde minerals are oxidized slowly by weathering agents, so that the sulphides of copper which find their way into a tailing pond are gradually changed into water-soluble and acid-soluble compounds. Commercially, the oxidation of copper sulphide minerals is accomplished by roasting them at elevated temperatures in air using a suitable (usually multiple hearth) roaster. Most copper smelters are equipped with such roasters. In this phase of the study we were especially interested in determining the effect of temperature on: (I) the air oxidation of chalcocite and (2) the oxidation of chalcocite using commercial oxygen. The amount of sulphur removed as sulphur dioxide, the percentages of water-soluble copper, and of acid-soluble copper were determined for the air oxidation tests. In the tests using commercial oxygen, the percentages of sulphur dioxide, water-soluble copper, acid-soluble copper, water-soluble sulphur and acid-soluble sulphur were determined. For these experiments the temperature was varied from 250 to 700°C. Experimental Preparalion of Chalcocite (Cu2S) Natural chalcocite is not pure, Minerals such as bornite, covellite, and chalcopy-rite may be present. It was decided, therefore, to prepare some chalcocite in our own laboratory. An intimate mixture of sulphur and hool divided metallic copper in the ratio of 4 g of copper to I g of sulphur was prepared. TO this was added a slight excess of

Jan 1, 1949

The phosphate pebble-bearing matrix in the Florida Phosphate Pebble Field has physical properties which make it readily adaptable to hydraulic transportation methods employing solids-handling pumps and pipelines. The abundance of water available, a practically flat terrain, low costs per ton-mile, and beneficiation of the matrix by agitation while being pumped have contributed to the popular choice of hydraulic transportation. Phosphate pebble mining in Florida, begun in the 1860's, first used high pressure water and solids-handling pumps for overburden removal about 1900. Removal of the average 25 ft of overburden was followed by hydraulic mining of the matrix, with 6-in. and 8-in. pumps handling 50 to 100 cu yds per hour being moved along the floor of the pit as they were advanced toward the face being undercut and slurried by hydraulic guns.

Jan 3, 1961

By John Birkinbine

This piece of Carpenter crucible steel has exhibited a tensile strength of 116,000 pounds per square inch, an elastic limit of 89,170 pounds, an elongation of 25 per cent., and a reduction in area of 42 per cent. The test-specimen had a length of 2 inches between fillets, and was an inch bar reduced to an area of 0.504 square inch. This unusual tensile strength was determined before the bar had been hardened so as to show the remarkably velvety fracture here exhibited; but a piece of the same, tested after hardening, is reported to have stood a stress of 214,000 pounds per square inch. Another test-piece is said to have shown 136,000 pounds tensile strength, 97,300 pounds elastic limit, 20 per cent. elongation in 2 inches, and 40 per cent. reduction of area. Mr. Carpenter claims that this steel, containing 2.27 per cent. chromium and 1.04 per cent. carbon, can be welded like iron, and has proved most desirable,for the highest class of die-steel.

Jan 1, 1895

By R. E. Somers

I. Introduction...........................604 1. Location, Topography, and Climate...............604 2. Scope of Work and Acknowledgments...............606 3. History and Mining......................606 11. General Geology.........................609 1. Introduction...........................609 2. Granite. :..........................610 3. Quartz Porphyry......................... 612 4. Monzonite........................... 614 5. Volcanic Breccia........,................ 618 6. Gravels............................. 619 111. Economic Geology......................... 619 1. Introduction........................... 619 2. Mineralogy........................... 619 3. Occurrence of the Ores...................... 622 4. Oxidation and Downward Enrichment............... 630 5. Rock Alteration........................639 6. Genesis of the Ores........................ 643 I. Introduction 1. Location, Topography, and Climate The Burro Mountains are located in the southwestern part of New Mexico, in Grant county. The group is made up of two distinct mountain masses, known as the Little Burros and the Big Burros, the former lying about 6 miles southwest of Silver City, and the latter about 9 miles farther in the same direction. They are separated by the valley of the Mangas River, a tributary of the Gila, and a stream only in name, except after a heavy downpour of rain. The Little Burros attain an elevation of 6,625 ft. above sea level, and the Big Burros 8,054 ft., with the surrounding country averaging about 6,000 ft. To the south of these mountains stretches the desert plain, while to the north are the more frequent elevations of the mountainous country.

Jan 1, 1916

By Pedro G. Salmon

The broad general distinction between primary and secondary batteries lies in the fact that in the former the current is produced by the consumption of one or both of the elements composing the cell, while in the latter the elements retain their form as such, and merely pass from one state of chemical combination to another. Much has been said in condemnation and but little in praise of storage-batteries; yet, notwithstanding the severe criticisms passed upon them, the skepticism with which electricians have viewed them, and the ignorance with which they have been handled, they continue to push their way into use. Their manufacture has now become a well-defined and established industry.

Jan 1, 1890

By R. J. Wensley

The use of small substations for the supplying of 275-volt energy to the locomotive and cutting machines in coal mines is a well-established practice. A few years ago, when labor costs were lower, these substations were located as near to the load as possible, and an operator was provided for each station. This practice has now become so expensive that substations are being located with reference to other mining machinery, such as hoists or pumps, so that one operator can look after both. Sometimes the substation is operated by one whose duties make him traverse quite a large area. In such cases the interruption of alternating-current supply may produce a long interruption in the direct current, as the station cannot resume service until this man reaches it. Such interruptions interfere seriously with production and may easily counterbalance the supposed saving gained by such operating methods. The grouping of substations for convenience in operating may also result in excessive copper loss and consequently poor trolley voltage, with its attendant evils of low locomotive speeds and increased locomotive motor maintenance. The speed of the coal-cutting machines will also be reduced. By relieving the substation of its burden of the operating labor cost, the most economical location, from an electrical standpoint, may be chosen. The matter of machine insurance should also be considered. If an attendant is caring for several kinds of equipment, he cannot watch the machine continually for signs of trouble; therefore, continued overload, phase failure, low alternating-current voltage, bearing trouble, etc. may result. Some partly automatic equipments have been installed; these have protection against low voltage, reverse current, and bearing trouble and are provided with automatic reclosing circuit breakers. This is a step in the right direction but it does not go far enough to give first-class machine insurance. The saving in maintenance costs is often the smallest item, when considering the automatic substation as machine insurance. When the coils in a machine are roasted out, due to continued overload or to opera-

Jan 1, 1922

ENROLLMENT of both undergraduate and graduate mineral engineering students rose approximately 11.8 pct over last year to a total of 12,830. Leading again in the enrollment climb was ceramic engineering which increased by about 21 pct. Approximated increases in enrollment of the other mineral engineering categories, in order, were: metallurgical 17.7 pct; petroleum 13.3 pct; geological and geophysical 3.3 pct: and mining proper, the lowest with 2.9 pct. Total ECPD school enrollment climbed to 242,405 -just below the 1947 peak, but 14.4 pct higher than 1955. Engineering enrollments have shown a general increase since 1951, and freshmen enrollments have climbed steadily since 1950.

Jan 5, 1957

By Donald M. Liddell

From a commercial standpoint, the only beryllium mineral warranting attention is beryl, 3Be.Al2O3.6SiO2, which is of fairly widespread occurrence. The chief deposits are in Brazil, Argentina, India, Canada and Portugal. When pure this contains about 14 per cent of beryllium oxide. The mineral richest in beryllium is phenacite, (BeO)2SiO2, or beryllium orth-osilicate, which contains 45.55 per cent beryllium oxide when pure, and if anyone is ever fortunate enough to discover a large deposit of it, it will revolutionize beryllium metallurgy. Gadoljnite, zBe0.Fe0.2Yz0~.zSi0~, is also often referred to as a beryllium mineral, though the occurrences are comparatively scant and it is of more interest as a source of yttrium than it is of beryllium. There has been a good deal of talk recently regarding some occurrences of helvite in the United States. Helvite is a complex manganese-iron beryllium silicate and, apart from difficulties that would arise in its treatment because of its compo-sition, the beryllium content of the known deposits is not high. Early Metallurgy The elemcnt beryllium was first isolated by L. N. Vauquelin in 1797.~ He crushed and heated beryl, having the idea that this heating made it more readily amenable to attack by chemicals, and then mixed the mineral with three times its weight of caustic potash and fused the mixture. The melt after cooling was dissolved in hydrochloric acid: dehydrated, and again taken up with hydrochloric acid and filtered to separate the silica. The filtrate was treated with an excess of potassium carbonate and the precipitate after draining was leached with a solution of caustic potash, which dissolved the alumina. The undissolved material was, in Vauquelin's own words, "une terre nouvelle." He dissolved the precipitate with nitric acid and evaporated it to dryness, took up with hydrochloric acid and threw the iron out with potassium hydrosulphide, though he found that to make a complete separation of the iron involved a second treatment. The solution, after throwing out of the iron, had a pronounced sweet taste, and though Vauquelin always speaks of working on "terre du beril" he suggests that the new element should be known as "glucine" (glucinum) from the Greek word for sweet, because of this outstanding property. Vauquelin did considerable work on the comparison of aluminum and beryllium, working out a separation of most of the aluminum based on its precipitation as alum. His work is reviewed at some length, since ordinarily his procedure is incorrectly stated. It will also be recognized by those who have studied beryllium metallurgy that a good many technicians have followed his ideas since, including preheating the beryl before treatment. The fusion with

Jan 1, 1944

By J. Gordon Parr, D. H. Polonis

RYSTALLOGRAPHIC relationships between martensitic a' (close-packed-hexagonal) and retained fi (body-centered-cubic) have been studied in binary alloys of titanium with manganese, molyb- denum, chromium, and iron.'" In these investigations, the habit planes of the martensitic phase were determined, as well as the orientation relationships between martensitic and parent phases. In each alloy

Jan 1, 1957

By Walter Crafts, C. M. Offenhauer

In a previous study of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is 2 more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about I to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, I per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to I-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudo-martensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously1 that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943