Search Documents

By R. A. Ritter, J. P. Batycky

A numerical technique has been developed to permit estimating the pressure gradient associated with laminar flow of thixotropic liquids through long Pipelines. For this purpose the pipeline is divided into a number of radial and longitudinal increments within which rheological properties of the fluid may be considered as constant at any time. Then, provided only that the fluid flow curve is defined at every duration of shear, it is possible to predict the instantaneous pressure gradient at any cross-section along the pipeline for each desired flow rate and pipe size. The technique consists of an iterative integration of shear rate to establish the appropriate value of the wall shear stress at each location. Consistency of fluid in the increment is determined by the flow history of that increment, while the radial flow associated with variations in velocity profile is accounted for by adjusting the width and radial position of the increment. A number of pressure profiles, computed at each of several flow rates, provide a convenient basis for pipeline design and pump selection. INTRODUCTION In recent years considerable attention has been given to predicting pressure drop associated with the isothermal laminar flow of time-independent non-Newtonian fluids in pipes and annuli. 6,11,12 The approach generally has been to develop analytical relationships between flow rate and pressure drop based on simple constitutive models which hopefully provide an approximate description of the rheological properties of the fluid. Analytical solutions are highly desirable since the influence of all pertinent parameters can be readily determined. Unfortunately, however, this approach is restricted to simple flow geometries and- frequently leads to erroneous results due to inadequacies in the model. In certain cases a solution may be obtained through applying appropriate numerical techniques.l,14 For example, a digital computer program is available for predicting the velocity profile and pressure drop encountered by any Newtonian or time-independent non-Newtonian fluid flowing under laminar conditions in a cylindrical pipe or annulus.l In this paper the consistency behavior of the fluid need only be described in terms of basic rheological data. Analyzing flow systems involving fluids with time-dependent rheological characteristics is considerably more complicated since substantial changes in consistency may occur because of sustained shear action. This sensitivity to shear frequently persists for several hours. Consequently, variations in pressure drop and/or flow rate resulting from the aging process and addition of unsheared or partially sheared fluid to the system must be considered for purposes of pipeline design. This paper outlines a numerical method for predicting the transient and steady-state laminar flow behavior of a thixotropic liquid in a pipeline of arbitrary length (i.e., at a specified constant flow rate, the instantaneous pressure gradient may be determined at any time after start up and at any location along the pipeline). Several such pressure gradient profiles, computed at several flow rates, may be combined to produce a complete portrait of the system response. This flow portrait provides a reasonable basis for pipeline design and for selecting a suitable pump characteristic. TIME-DEPENDENT RHEOLOGICAL BEHAVIOR The most familiar time-dependent rheological properties are those exhibited by thixotropic liquids. Many of these materials, particularly thixotropic crude oils, generally display an apparent yield stress in that a finite pressure gradient is required to initiate flow. Then, under the influence of sustained shear at a constant shear rate, the consistency systematically decreases to some final limiting value. The shear stress obtained at

By C. S. Smith

QUANTITATIVE methods were used to good effect in the earliest days of metallography1-3 but they mysteriously passed into virtual disuse until the important paper4 by Howard and Cohen in 1947. Various devices for the measurements of integrated linear intercepts have been constructed, primarily by petrographers. The hydraulically operated stage designed by the writer5 was satisfactory, but prolonged use caused air bubbles to become entrapped, which introduced back-lash. A new stage has been constructed which avoids this defect and provides better integration when measuring directional structures. This utilizes a circular traverse, and integration is achieved by counting electrical pulses produced by a photocell and a light chopper.* The stage is shown diagramatically in Fig. 1 and in photograph, Fig. 2. It is of simple construction. Mounted on a plate with clamps to fit the stage of a standard metallurgical microscope is a worm and 100-tooth worm gear, the latter supporting the specimen to be measured. The worm is manually actuated by a knob which contains inside it three

Jan 1, 1961

Estimation of local recoveries is an important issue in a selective mining operation. Two techniques, probability kriging and multigaussian kriging, are applied to estimate local recoveries at Jerritt Canyon. The pros and cons of each method are discussed in light of the results. Both methods provide simple and satisfactory solutions to the problem of estimating local recoveries. Consequently, they can be useful tools to work with in a selective mining operation.

Jan 1, 1986

By T. P. Papazoglou, N. A. D. Parlee, W. C. Phelps

HE high vapor pressures of metals such as lead, calcium, lithium, bismuth, and magnesium at steel-making temperatures present experimental problems which have thus far rendered it almost impossible to obtain really reliable data for their solubilities in liquid iron. Many investigators have attempted to equilibrate liquid iron in the same crucible with the undissolved liquid phase of such volatile metals. The published results,l-6 although useful, are often questionable on the grounds of not being obtained under true equilibrium conditions. Such information is not always of practical value in any case since the equilibrium vapor pressure is often several atmospheres and steel is not currently made at these pressures. Solubility measurements at lower partial pressures (< 1 atm) appeared to be more practical and easier to make. These data could be used to calculate solubilities at other pressures where Henry&apos;s Law is obeyed, and to estimate solubilities under other conditions of temperature and pressure with useful accuracy. This note outlines the development of a general technique for the measurement of solubilities in systems of this kind. The method involves equilibration of the high-boiling metal at known temperatures with the vapors of a low-boiling metal at known partial pressures. Analyses of quenched samples provide vapor pressure-solubility data and make calculations of alloy thermodynamics possible. The principle involved is similar to the closed-system diffusion-transport method which is difficult to apply with most high-melting liquid metals like iron, due to closure problems. A two-zone horizontal (molybdenum wire element) tube furnace, Fig. 1, provides two constant-temperature zones in a reaction tuve (3/4 in. ID by 1 in. OD by 36 in.). A high-boiling metal sample, 9, introduced in the higher-temperature zone, is maintained at temperature T1, and a volatile metal sample, 7, in the lower-temperature zone, is held at T2. A stream of argon with 10 pct hydrogen is passed via flowmeters, 1, and mixing-drying towers, 2 and 3. through the reaction tube at a favorable flowrate and acts as a carrier gas which entrains vapor from the volatile liquid metal at a specific constant partial pressure. The gas mixture passes through a system of constrictions, 6 and 8, to the higher-temperature zone, establishes intimate contact with the high-boiling liquid sample, 9, and exits through a small condenser tube. The entire system is at (nearly) atmospheric pressure and the volume of carrier gas passed is measured with a wet gas meter. When the high-boiling sample attains equilibrium with the vapor phase, both samples are removed and quenched. Analysis of the high-boiling sample for solute content reveals its solubility for the low-boiling metal at a vapor pressure calculated from carrier-gas volume and either a) weight loss of volatile metal or 6) weight gain of high-boiling sample plus condenser (which collects the undissolved vapors). To test the capabilities of the method, liquid silver at 1403&apos;C was equilibrated with lead vapor at various partial pressures. The relatively simple Pb-Ag system was particularly suitable for uncovering experimental problems and providing the first step toward investigations with more volatile metals and more difficult combinations.

Jan 1, 1965

By Y. Dardel

Since the first determination of Dumas1 in 1880, many authors have tried to measure the solubility of hydrogen in solid aluminum, or at least the amount of dissolved gas in it. However, the interpretation of the results which have been obtained is still difficult. Sieverts? then Baukloh and Oesterlen,a during their gassing experiments could not determine any solubility of hydrogen in solid aluminum. On the other hand, Portevin, Chaudron and Moreq4 leaving the determination of the hydrogen solubility beyond the scope of their experiments, measured only the amount of gas that they could extract by high voltage positive ion bombardment and found up to 151 cm3 of gas per I00 g of metal. Winterhager,6 by repeated vacuum extraction during severe cold rolling, extracted up to 161 cm3 per 100 g. In both series of experiments, the extracted gas contained chiefly hydrogen with a small amount of nitrogen, carbon monoxide, carbon dioxide and methan. Later, Schmidt and von Schweinitze as well as Chaudron and Moreau7 showed the importance of the adsorbed layer of hydrogen, the extracted quantities being proportional to the surface and not to the weight of the sample, when its cleaning was not perfect. In earlier experiments, Steinhausers extracted from more massive samples nothing but a little amount (< 0. 5 cm3 per I00 g) of hydrogen, carbon monoxide and methane. Thus, according to these experiments the quantity of dissolved gas is probably very small and the effect of the surface could falsify the results of the extraction. However, owing to the care taken by Chaudron and his coworkers, it was clear that all the hydrogen extracted could not come from the superficial layer, or that the links which bound hydrogen to the surface were so strong that the usual method of cleaning could not destroy them. After the main parts of the experiments reported here had already been carried out, Eborall and Ransley9 published the results which they obtained with an analysor having an accuracy of 0.03 cm3 per I00 g, while that of the usual apparatus was only about 0.2 cm3 per I00 g. During all their experiments the adsorbed layer would have been a difficulty, for the value of the adsorbed hydrogen was approximately equal to that of the dissolved amount. Table i—Amount of Adsorbed and Dissolved Hydrogen (After Eborall and Ransley) Extraction Hz Adsorbed „ h2 dissolved Temperature Calculated Extraction OCcma 500 0.057 0.050 600 0.062 o.096 Since always keeping the same adsorbed layer is very difficult, an error in the correction for the adsorption can be made when using the apparatus of. Eborall and Ransley, as well as the earlier apparatus.

Jan 1, 1949

By G. H. Tausch, T. A. Huber

Very encouraging progress has been made ill the develop-ment of the permanent-type well completion which decreases considerable the cost of completions and workovers and aid-in the acquisition of reliable reservoir information at low cost. Completion and remedial operations are performed with tool,; which pass through the well tubing. Perforating and plug-hack operations can be done with the tubing in place and do not require pipe-handling equipment. Because of the many advantages afforded by this method, development work is going forward in anticipation of ultimately being able 10 use it to perform all usual well completion and workover operations. Effort is also being directed to the development of a more permanent type of lift equipment suitable for use with the permanent-type well completion. INTRODUCTION The permanent-type well completion in one in which the tubing and well-head are set in place only once in the life of the well and the completion or remedial work is performed through the tubing with a tubing-type perforator. a retrievable tubing extension. and other wire-line tools. This new type completion has made possible the saving of one to two days&apos; rig time in the completion of each of several hundred wells During the last two years, and use of equipment developed for this type of completion has resulted in a 75 per cent reduction in cost. of certain types of workovers. In addition. the more reliable indication of the commercial value of a reservoir and the more accurate general reservoir information made Possible promise to be of even greater value in oil recovery than the reduction of costs for completions and workovers Recently. several well.. were worked over by using the retrievable tubing extension suspended on a swab line to plug back with cement and then perforating a higher producing interval with the tubing-type perforator, thus opening the way for complete through-the-tubing workovers which may be performed without pipe-handling equipment or mud. Those items attendant to the use of pipe-handling equipment and mud. such as hoard matting rig substructure. and pits. were also eliminated. There are indications that the elimination of drilling mud during completion and workover operations will frequently give increased well productivity, as plugging of the perforation. will not occur. It ii now possible to perforate selectively small sections of the producing interval and to test a well through these sections prior to perforating more interval. The perforating of additional interval will not entail the costly operations of killing the well and pulling tubing, nor will the old or the new perforations be plugged. The productivity of .mall sections of a reservoir and the actual gas-oil or oil-water contacts may now be determined economically under flowing condition.. Selective completions can be made in this manner to delay gas and water problems and bring about maximum oil recovery. At the present time, gas lift appears to offer the greatest potentialities for artificial lift in the permanent-type well com"letion since it can provide full-open tubing to accommodate the through-the-tubing tools and it may be ultimately developed into a fairly permanent type of lift. With precent-day pas-lift equipment. valve or mandrel failure necessitates occacio11al removal of the tubing. thereby reducing to some extent the permanence of the completion. New gas-lift valves are now

Jan 1, 1953

By J. Price Wetherill

The coal-seams that are worked vary from 3 1/2 to 100 feet in thickness, and occur at all angles of inclination, but are never flat for any great extent. They contain coal, slate, and an unsolidified coal, called dirt by the miners, in various proportions, a uniform seam of coal alone being rare. The upper walls are composed of conglomerate, sandstone, or slate; the first two hard and solid in texture, and withstanding the action of the atmosphere and moisture sufficiently well to offer but little trouble to the mining operations; while the latter crumbles rapidly, owing, in part, to the decomposition of iron pyrites which it contains in large quantities, and in part to its own friable character, and requires constant care to avoid accidents to the men working below it, and to prevent its mixing with the coal mined. The floors are composed of slate. As in all mining operations, the general system pursued is to reach with a permanent outlet such a point in the seam as will

We are pleased to announce the appointment of Dr. Harrison W Craver, until recently librarian of the Carnegie Library in Pittsburgh, to be Director of the combined libraries of the American Society of Civil Engineers, the American Institute of Mining Engineers, The American Society of Mechanical Engineers, the American Institute of Electrical Engineers, and the United Engineering Society. DR. HARRISON W. CRAVER. Dr. Craver was born in Owaneco, Illinois, August 10, 1875. He was educated in the public schools of Carmi, Illinois, and Terre Haute, Indiana, and the Rose Polytechnic Institute, from which he was graduated in 1895, having specialized in industrial chemistry. The following year he spent in post-graduate chemical study with Dr. W. A. Noyes. In 1896 he became chemist to Kirkpatrick & Co., Limited, of Pittsburgh, and later to

Jan 5, 1917

By M. E. Grimes

A method of predicting uranium extraction rate in underground bacterial leaching of as-blasted ore has been developed. The method is based on the hypothesis that extraction is directly proportional to the volume of a piece of ore that is penetrated by the leaching agent, and that each piece of ore, regardless of size, has been penetrated radially from the external surface to the same depth at a given leaching time. Consequently, given an initial size and assay distribution, extraction should be predictable for a given penetration. Two laboratory bacterial leaching tests under simulated stope leaching conditions were carried out for a periods of 89 and 96 weeks. On completion, the residual ore was screened and analyzed. The information so obtained was employed to provide an elapsed time base for the penetration model, from which predictions of future extraction were made. The finding of solubilized uranium trapped within apparently sol id ore pieces was unexpected. However, it is not recoverable except after crushing, and hence does not affect calculations of underground leaching .

Jan 1, 1974

By Nichols J. Grant, Bill C. Geissen

In low temperature phase diagrams, liquidus curves below about 1500°C are relatively easily established, e.g., by thermal analysis or separation of coexisting solid and liquid phases, followed by chemical analysis. Experimental difficulties increase considerably at higher temperatures and in systems involving more reactive metals. Although there are now thermocouples available for use from 1600" to 2400°c, as summarized by Caldwell,&apos; the need for frequent calibration, aging, and contamination problems, and unavailability of suitable protection tubes has sharply limited their use at higher temperatures. Many of the high melt- ing metals are found to react with refractory oxides. TO avoid such problems, a frequently used procedure is the diffusion and saturation method, as described by Spedding et a1.&apos; for the system La-C. This technique involves the annealing of one metal or a suitable alloy in a crucible of the other element at a temperature above the melting point, followed by chemical analysis of the center of the melt, after equilibrium is established. Further, if an alloy system is to be investigated employing the electron microbeam probe, and calibration charts have been established, it may be possible to measure the alloy concentration at the center of a cored as-cast structure, and to conclude from this points on the liquidus curve in a manner similar to the one to be described. It is known that in phases with a broad homogeneity range the rapidly cooled, cored, as-cast structure of an alloy presents concentrations having different lattice constants; this spread of lattice constant values contributes to the broadened lines of a powder pattern for the as-cast condition. The region of the crystal which is first to solidify will then correspond to the edge of the lines if the change of the lattice parameters with concentration is monotonous. In the course of the determination of the Ta-Tr phase diagram,3 it became evident that such behavior made it possible to construct the

Jan 1, 1963

By John Jan

Iodine is a soft, lustrous, grayish-black non- metallic element with a density of 4.9. It is the least active of the four members of the halogen family. The other members are, in order of increasing activity, bromine, chlorine, and fluorine. Iodine is a solid at ordinary temperatures, while bromine is a liquid and chlorine and fluorine are gases. Iodine melts at 113°C and volatilizes at 184.4°C to a blue- violet gas with an irritating odor. It occurs in nature only as iodates and iodides or other combined forms. It was discovered by Bernard Courtois in France in 1811, who noticed its presence as an unknown substance in crude soda ash obtained from burning seaweed. Gay-Lussac recognized it as a new element and named it iode, from the Greek word "ioeides or iodes" for violet color (MacMillan, 1970). The world production is not known with any great certainty, but it is probably between 20 and 25 million lb per year, of which about 25% is consumed in the United States. Geology and Mineralogy Iodine compounds occur as a minor constituent as a mineral in the Chilean nitrate deposits and in solution in brines and sea- water. According to the U.S. Geological Survey, it is the 47th most abundant element in the earth&apos;s crust. The minerals lautarite, Ca (10,) (calcium iodate), and dietzeite, Ca, (10,) , (CrO,) , (calcium iodate-chromate) are found in Chilean nitrate deposits which are located in Antofagasta and Tarapach provinces on the eastern slope of the coast range in a desert area. Various brines contain iodine compounds. Seawater contains about 0.05 ppm of iodine and some seaweeds will extract and accumulate it up to 0.45% on a dry basis. Some coals in West Germany also contain iodine compounds. The known and potential sources of iodine reported in 1968 are given in [Table 1]. Iodine has been recovered from brines in Java, Indonesia, France, England, and the USSR. Iodine has also been recovered from seaweed in Ireland, Scotland, France, Japan, Norway, and the USSR. The indicated re- serves and future resources of iodine are large but have never been adequately measured. Analysis Iodine as the free element can be detected by the characteristic blue color it gives to a starch solution. Quantitatively it is determined as the free element by titration with standard thiosulfate solutions using starch as an indicator. Colorimetric methods are also applicable.

Jan 1, 1975

By F. O. Garrabrant, F. S. McNicholas, Robert Henderson, R. U. King

Several years ago, it was decided to experiment with the use of high-pressure water to bring in finger hangups and reduce the amount of secondary blasting necessary. It was argued that the velocity effect of the high-pressure water would bring down hangups without unduly wetting the ore. Water under a head of about 550 ft. was installed in certain slusher drifts. Ordinary ¾ in. water hose, with a nozzle opening of % in., was used, and water was impinged on the fines under a hangup. Results were excellent. About half the total number of hangups were brought in with high-pressure water without blasting and the cost of this part of the slushing operation was reduced about 50 per cent. Operations were speeded up, dust counts and safety hazards were reduced, and a more desirable working place was secured. The additional water added to the ore was under one per cent and caused no inconvenience in slushing, haulage, or crushing operations. Usually the ore would absorb all of the water, so that none of it would enter the loading drifts. The entire mine, developed by slusher drifts, is being equipped with high-pressure water. Heating Mine by Compressor Cooling Water Several years ago, the problem of heating certain sections of the mine during freezing weather became important. It was calculated that there was sufficient heat in the compressor cooling water to heat the incoming ventilating air current to above freezing, if such heat could be transferred from the water to the air. All schemes of radiation from pipe were rejected as too cumbersome, costly and impractical. It was thought that by spraying the heated water from the compressor cooling system into the incoming air, a satisfactory heat exchange could be accomplished. The only objection was that the sprayed water would freeze and might fill the air-intake drift. However, when water at about 75° to 80°F. was sprayed at the rate of 200 gal. per minute through a bank of sprays into the incoming and freezing air current, this air was thereby heated to above freezing; and although some ice was built up in the air drift, the amount was not objectionable. Occasionally the built-up ice was picked down into the outgoing water stream, which removed it. The entire south and westerly parts of the mine were prevented from freezing. Concreting for Hangups Considerable trouble was experienced in securing hangups of fine ore in slusher fingers that needed repairing. Regular methods of timbering were unsatisfactory. Now, a slab of concrete is poured over the top of the muck by Pumperete machine, almost filling a finger, which gives a satisfactory slab to work under for making the needed repairs. Derailers Some trouble has been caused by motor-men not observing safety lights and

Jan 1, 1946

By William E. Horst, John H. Bassarear

A technique is described which simplifies the standard procedure for measuring the Bond work index of a specific ore and illustrates how to overcome the strict requirements regarding feed size distribution normally encountered in operating plants. Actual results obtained from various process streams in a copper concentrator are presented and the grindability data are discussed in relation to the observed plant performance. This type of information can be used to gain a better understanding of plant behavior and to assist in the evaluation of plant modifications and process control studies.

Jan 1, 1977

By Frank L. Gaddy

Falls of roof account for over 50% of the fatalities that occur in coal mines in the US. Thus, roof control is one of the more important phases of underground mining. In reality, the control of roof influences the system of mining and is a major determinant of the width and spacing of working places, operations at the mining face, ventilation control, and surface subsidence. Frequently, the control of roof is the largest single cost item. Roof control is a never-ending task, not only at the working face and throughout sections where men are working, but along haulways and air- ways that must be maintained for the life of the mine. This is because roof, even the best of roof, slowly deteriorates, so it must be frequently examined, with corrective support applied when needed. As coal is excavated, stresses are set up in the roof because the previous equilibrium is upset, resulting in pressures that cause fractures and slight movements that are frequently hard to detect. Unless the immediate roof, in the excavated area, is given support by artificial means, it might fall or there might be a succession of falls, varying from a thin scale to several feet, depending on the nature of the top. Exceptions to this are those rare mines, or sections of mines, with hard, strong, nonweathering roof that requires no support. GENERAL CLASSIFICATION OF ROOF There are two broad types of roof as far as support is concerned: the immediate roof above the coal and the main roof. Artificial support for mining purposes is only concerned with the immediate roof as nothing except large blocks of solid coal, or massive concrete, will support the main roof. The immediate roof is generally a few feet thick but can vary from inches to 6.1 m (20 ft) or more. There are examples of where there is no immediate roof as the massive main roof lies directly on the coal

Jan 1, 1981

By F. A. Forward, A. H. Ross, J. Halpern

Application of the carbonate leaching process to carno-tite ores has often been limited by the difficulty of obtaining simultaneous high recoveries of uranium and vanadium. The chemical aspects of this problem are discussed and the effect of prior roasting procedures on this discovery is described. IN treating carnotite ores by carbonate leaching it is often necessary to subject the ore to a prior roast. Among the advantages that may result from roasting are: 1) improvement in settling and filtering characteristics of the ore; 2) destruction of carbonaceous impurities that would otherwise contaminate the leach solution and consume carbonate reagent; and 3) substantial increase in extraction of vanadium, which is usually low when the un-roasted ore is leached. Recovery of vanadium may be an important factor in processing carnotite ores, and the fact that vanadium is usually recovered in good yield by acid leaching has often been an economic advantage over results obtained with carbonate leaching. It has been found that response of an ore to carbonate leaching, following roasting, depends primarily on its composition and on the conditions of the prior roast treatment, particularly with regard to the roasting temperature, the atmosphere maintained above the charge during roasting and cooling, and the presence of certain reagents. These factors, especially the last, virtually determine the extractions of uranium and vanadium attainable by carbonate leaching, as well as the reagent consumption on leaching, whereas adjustment of the leaching conditions has only a limited influence. These variables were examined systematically to elucidate roasting and carbonate leaching of carnotite ores and to establish a treatment yielding high recoveries of both uranium and vanadium. Tests were conducted on samples of four different Colorado Plateau ores, described in Table I. Roasting Procedure: The roasting tests were conducted in an electrically heated furnace in which the temperature was controlled to ±15°C. The ore (usually a 500-g charge) was ground to —100 mesh, mixed with the desired reagent, and spread in a silica tray to a bed depth of about 1/2 in. During the roast the charge was rabbled at intervals of 15 min. To provide free access of air the furnace was usually ventilated; however, in a few experiments a controlled atmosphere such as carbon dioxide or hydrogen was maintained above the charge. Leaching Procedure: The pulp, generally comprising 500 g of ore and a 2000-cc solution containing 80 g per liter of Na2CO8 and 20 g per liter of NaHCO3, was agitated in an autoclave at 120°C, under 30 psi 02. Samples were withdrawn periodically, and the solution and ore residue were analyzed. Under the conditions employed, maximum attainable extractions were generally achieved in 4

Jan 1, 1959

By J. F. Enrietto

It is shown that one cannot approximate the broad internal friction Peaks observed in the Fe-Mn-N system as the sum of a number of subsidiary Peaks and still vetain the concept of a single relaxation time. Furthermore, the approximation of manganese affectirg only nearest neighbor interstitial sites is shown to be incompatible with the experimental results. The results of this experiment show that the influence of manganese in the ferrite lattice extends over 3 to 4 atomic distances. NUMEROUS experiments have shown that the presence of relatively small amounts of substitutional alloying elements can profoundly affect the profile of the damping spectrum in the vicinity of the Snoek peak in bee metals.1-7 Dijkstra and Sladekl observed this phenomenon in Fe-Mn-N alloys where it appeared as a broadening and shifting of the Snoek peak to higher temperatures. The authors interpreted this as being the result of a superposition of two damping maxima—the normal Snoek peak, located at its usual position and having a normal half-width, and an interaction peak having a normal half-width, but occurring at a somewhat higher temperature. They prclposed that the interaction peak was caused by nitrogen atoms jumping from Fe-Mn sites to Fe-Fe sites, the Fe-Mn interstitial sites having one manganese and one iron atom as nearest neighbors, and the Fe-Fe sites having two iron atoms as nearest neighbors. They further suggested that the Fe-Mn sites had a lower energy than the normal Fe-Fe sites because of the presence of the adjacent manganese atoms. From the relative heights of the two postulated damping peaks, the dif-

Jan 1, 1962

By W. E. Ruder

It has been pointed out by Stead1 that grains of considerable coarseness may be developed in steels containing from 3 to 5 per cent. of silicon, and in a previous paper2 the present author has shown that under the proper conditions of annealing single grains having an area of 50 sq. cm. may be obtained. It is the purpose of this paper to discuss in more detail the conditions promoting the growth of these grains, in the hope that the experiments described may throw some additional light upon the general problem of grain growth in metals. These silicon steels lend themselves particularly&apos; well to such experiments because of the ease with which the change in structure may be followed and because of the fact that the effect of the carbon present is largely obliterated by the high percentage of silicon. This forms a solid solution with the iron, which acts very much like a pure metal. This alloy has been found to have but one critical point, viz., Ar2. This point, determined by Roberts-Austen for Hadfield&apos;s 4 per cent. Si alloy, was found to lie at 703" C. Vigouroux3, in working with pure Fe-Si alloys, finds this point to rise from 750" C. for 0.5 per cent. Si to 860" for 6 per cent. alloy, with a flat region in the curve from 3 to 4 per cent. Si. No accurate determination of this point has been undertaken by the present author, but it has been roughly determined to lie between 730" and 750:. In the preliminary experiments, some of which have been described in a previous paper, it was found that practically all of these steels, when annealed to 1,200" C. or higher, showed grains of comparatively large size. These grains varied in size, however, from about 4 sq. mm. to 50 sq. cm. (see Figs. 1 and 2) under the same conditions of anneal, and it was for the purpose of determining the cause of this difference in size that the experiments herein described were undertaken. From a preliminary study of the chemical composition of the specimens

Jan 1, 1914

By F. J. Dunkerlery, V. Damiano, J. Fulton, F. Pledger

Grain-growth and recrystallization characteristics of a commercially pure zirconium prepared by the iodide process are reported. Grain growth from 640° to 800°C was continuous once initiated and obeyed D = kt". Recrystallization of zirconium occurred at temperatures of 450° to 550°C after deformations of 20 and 50 pct. Hardening from partially soluble inclusions prevented determination of the absolute rates of recrystallization, but the relative rates of recrystallization obtained are useful as a guide in fabrication practice. BASIC information needed as a guide in the hot and cold working and annealing of metals includes recrystallization and grain-growth data. A search of the literature revealed no such information for pure zirconium. This is a report of practical grain-growth and recrystallization results obtained for a commercial grade of pure zirconium on a project sponsored by the Office of Naval Research. In this work, isothermal grain-growth curves were obtained at five temperatures from 640" to 800°C inclusively; while recrystallization curves have been determined at 450°, 500°, and 550°C for the metal at the deformation levels of 20 and 50 pct. In addition to the usual variables of temperature, time, and deformation, distribution of the second phase found in all commercial grades of iodide zirconium is also treated as an important factor in these grain-growth and recrystallization studies. In conducting this work, two properties of zirconium were particularly pertinent in dictating experimental conditions. First, since zirconium undergoes a transformation from the a close-packed hexagonal form to the ß body-centered cubic form at 862°C, no recrystallization or grain-growth studies were made above 800°C. Second, because dissolved gases (oxygen, nitrogen and/or hydrogen) increase the hardness and lower the ductility of the solid metal, all annealing treatments in this investigation were carried out in vacuum or in a helium atmosphere. Materials and Methods The zirconium used in this investigation was prepared by the Foote Mineral Co. by deposition from its iodide. A spectrochemical analysis of the metal showed the following composition in weight pct: Hf, 2.1; Mg, 0.012; Fe, 0.035; Si, 0.095; Ti, 0.023; Al, 0.037; Mo, trace; Ni, trace; Cr, trace; Ca, 0.006. Conventional metallographic procedures involving hand polishing on wet metallographic papers, followed by final polishing on fine, levigated alumina on gamal cloth and a medium speed wheel were used throughout this investigation. Grain boundaries were revealed with modified Tucker&apos;s etch containing 20 parts glycerine, 2 parts hydrofluoric acid, and one part nitric acid. Grain-Growth Procedure: Three lots of zirconium, designated here as series A, B, and C were prepared for the grain-growth studies as follows: Series A was prepared by cold swaging the % in. as-deposited rod to a 3/16 in. final diameter, followed

Jan 1, 1952

By Alex McCoy

SAMPLING of the fluid from oil wells for percentages of oil, emulsified oil, and water during the last two years has brought out some interesting facts concerning oil-water emulsion. This result led to a laboratory investigation of emulsion, which substantiated the conclusions made from the field observations. The purpose of this paper is to present the information collected, the laboratory experiments, and our interpretation of the same. In order to define emulsified oil exactly, give its synthesis and origin, and to show how and when it is formed in the wells, the work was necessarily divided into two separate lines-laboratory work and field observations. It is hoped that this study may lead to a discussion of such points so that the petroleum engineer, geologist, or technologist may be benefited by its practical bearing on oil-field management. Special credit is due Mr. Everett Carpenter, chief geologist of the Empire Gas & Fuel Co., for his assistance and cooperation in this work. LABORATORY INVESTIGATIONS ON EMULSIFIED OIL Laboratory investigations were conducted in an attempt to learn the composition and some of the properties of emulsified oil, or B. S., as it is more commonly called, also to demonstrate, by laboratory methods, how B. S. may be formed under conditions similar to those existing at the time a well is being pumped, and how it may be broken down. Literature bearing on this subject is widely scattered and very limited in scope. Bacon and Hamor define B. S., or bottom settlings, as "earthy matter, inert organic matter, or, in the case of Pennsylvanian petroleum, an emulsion of paraffin wax and water, which accompanies crude oil." In this discussion we will limit the term B. S. to that heavy,

Jan 8, 1919

By Frank Foote, E. R. Jette

In recent years the constitution of the high-silver aluminum-silver alloys has been extensively investigated. Hansenl has reviewed the literature to 1935. More recently, Obinata and Hagiya,2 Hofmann and Volk,3 Taziri4 and Tishchenko5 have confirmed the general features of the phase diagram in the region around 25 atomic per cent aluminum. In this paper we present the results of high-precision measurements of lattice constants of the silver-rich alpha solid solution in the homogeneous range and the neighboring two-phase regions. These results are used to establish the nature of the solid solution, the identity of directly measured densities with those calculated from lattice constants and the homogeneity limits of the alpha solid solution with respect to three different neighboring phases. A study of the earlier investigations indicated that the last two subjects in particular required new and accurate data. Experimental Procedure Preparation of the Alloys.—The alloys were made from high-purity silver and aluminum. The silver was "Proof Silver," 99.999 per cent pure, supplied by the U. S. Metals Refining Co. The aluminum was 99.97 per cent pure (contained Si, 0.009 per cent; Fe, 0.0016 per cent; Cu, 0.004 per cent) and was supplied by the Aluminum Company of America. The lattice constants of these two materials have been reported by Jette and Foote.6 Weighed amounts of the two metals were placed in alundum crucibles and melted in vacuo in a high-frequency induction furnace. The melts were allowed to cool in the crucible, the ingots thus obtained weighed about 10 grams. These ingots were then filed clean, hamered, again cleaned and given a homogenizing anneal in vacuo of from 6 to 15 days at temperatures ranging from 500" to 695°C. The ingots were air-cooled from the annealing temperature. Lattice-constant Measurements.—Carefully prepared filings for X-ray analysis were sealed into evacuated quartz or Pyrex tubes and annealed for various periods of time at suitable temperatures. The furnaces used were vertical, rapid-quenching furnaces, the samples being quenched by crushing the sample tube under water by means of a heavy plunger. The general X-ray technique has been previously described6 The cameras were of the symmetrical, back-reflection, focussing type. Ka, radiation from a cobait-nickel alloy target was used. The wave-length values were taken from the second edition of Siegbaum&apos;s book.7 A correction for the index of refraction was applied and the lattice constants were calculated by the method of Cohen.8, 6 The lattice constants were calculated to a common temperature of 25°C., using the value of the linear expansion coefficient of pure silver as 18.9 X 10-6. Presumably the expansion coefficient for

Jan 1, 1941