Search Documents

By R. W. Raymond

THE specimen of anthracite which I exhibit is from the Ortiz Mine Grant, about fifteen miles southwest of Santa Fe. The beds belong to the lignitic formation of the Galisteo, which Hayden and

Jan 1, 1874

By Oliver C. Ralston, James Norman

DIATOMACEOUS earth occurs in deposits widely distributed throughout the nation. The chief producing areas are in the Western States, where many high-grade deposits are known. Eastern deposits of diatomite are unsatisfactory for many purposes either because of impurity or because of the extremely fine particle size. Eastern users of diatomite, on the whole, must pay for transportation of the material from the west coast. The freight rate is necessarily high because of the great bulk of the diatomite. A satisfactory process of purifying the diatomaceous earths of Maryland and Virginia, which are unsuited for wide use only because of impurities, should be of value to eastern users. In the past, benefication of diatomite by wet processes has been limited to classification or sedimentation for the removal of sand from diatoms. Calcination with salt is used to produce a white diatomite when iron is present in the impurities, and small amounts of clay are rendered inactive in the process. No treatment has been developed whereby a large proportion of clay can be removed from a low-grade diatomaceous earth to give a diatomite of very high purity. In August 1937 the Federal Bureau of Mines, in cooperation with Dr. R. C. Williams, of Baltimore, undertook the problem of purifying low-grade Maryland diatomite by froth flotation. Work was done at the Eastern Experiment Station, College Park. Unless otherwise stated, the crude diatomite used was from the Patuxent River deposits near Dunkirk. This material, consisting of roughly one-third each of clay, quartz sand and diatoms, was representative of the usual low-grade marine diatomite found in the Coastal Plain Miocene beds of Maryland and Virginia and sporadically in other Atlantic coast states. As received, it contained 50 to 60 per cent moisture and probably had been wet since its formation.

Jan 1, 1940

By E. L. Larison

DURING the early years of the present century a notable interest appeared in American industry in the matter of recovering and render-ing profitable byproducts of manufacturing operations. Among the byproducts of reduction of sulfide ores in many plants large amounts of sulfur dioxide gas were available. In certain instances the concentration of S02 in the gases evolved was, or could be made, sufficient to make them suitable for manufacturing sulfuric acid. At the Anaconda Reduction works such a condition existed. Large tonnages of copper concentrate were being roasted and the roaster gases were available and suitable as a source of sulfuric acid. Earlier work on a large scale at Martinez, Calif., and in the Ducktown region, Tennessee, had shown the feasibility of manufacturing sulfuric acid from the S02 contained in gases arising from the reduction of copper sulfide ores. In California and Tennessee the acid found a ready market in manufacture of fertilizers, while the situation regarding disposal of the sulfuric acid was quite different at Anaconda. No local use for acid existed, and a commodity of such low value could not stand freight charges to consuming centers. There was a very large accumulation of sand tailings from the gravity concentration mill below the plant at Anaconda. This material, made by the comparatively crude methods in use up to about 1915, contained about 13 lb. of copper per ton, largely as sulfide minerals. In 1912 serious research work toward recovery of this copper was instituted and after about two years of laboratory and pilot-plant development, a process for accomplishing it was perfected. This process involved roast-ing the sand tailings, leaching the roasted tailings with sulfuric acid, and throwing out the copper by passing the solutions over scrap iron. Under this plan each ton of sand required the introduction of about 70 lb. of 60° Be. sulfuric acid.

Jan 1, 1934

By R. V. Lundquist

Leaching manganese-bearing materials with NaOH to remove caustic-soluble silica has been demonstrated as a method for upgrading manganese. Those materials containing opaline varieties of silica respond most readily. Spent leach liquors are regenerated by treatment with lime to precipitate calcium silicate and to reactivate the NaOH for leaching. ALL of our larger domestic deposits of manganese are very low grade, but estimated tonnages in these deposits are large enough to constitute a potential strategic reserve of manganese for emergency periods, provided these ores can be upgraded sufficiently to meet industrial specifications. Many types of processes have been suggested for upgrading these ores, several have been studied in pilot plants, and a few have attained limited commercial production for special purposes. The hydrometallurgical process to be described below proposes a leaching operation for removing caustic-soluble silica and other gangue minerals and consequently upgrading a manganese ore or flotation concentrate to a commercially acceptable moduct. It is known that some forms of silica and some silicate minerals are soluble in NaOH solutions under suitable conditions. This new process proposes to use NaOH for removing the soluble materials from manganese ores or concentrates and, as a result, upgrade the manganese content. Since spent leach liquors are not efficient leaching agents the liquor must be treated with lime to precipitate calcium silicate and reactivate the NaOH. Experimental Procedure Manganese-ore samples ground to —35 mesh were leached in iron containers into which the ore sample and appropriate NaOH solutions were placed. Flotation concentrates were already ground to —200 mesh. The slurries were then placed on a hot plate or into a pressure digester and stirred continuously during the period of digestion. Where the- digestion was performed at atmospheric pressures, water lost by evaporation was replaced at regular intervals to maintain approximately a constant volume of slurry. In the pressure digester, volume changes were not controlled. After digestion, the slurry was allowed to cool enough for easy handling, but it was filtered hot, 50" to 70°C, on a Buechner filter. Filtration under these conditions was satisfactory. The resulting filter cake was washed and dried. In most instances, a single leach would not produce maximum extraction of silica from the ore sample; consequently, the dried tailing was treated again in the same manner with a fresh solution of NaOH to obtain an additional extraction of silica. This procedure was repeated a number of times to get the maximum extraction of silica. Usually three or at most four stages of leaching were adequate for this purpose. This leaching procedure was used for obtaining the data reported in this paper on the effects of NaOH concentration, pulp dilution, temperature, and time of digestion on the efficiency of extraction of silica from the ore sample. The experimental procedure does not match industrial methods. consequently tests for counter-current leaching were set up. Data from these tests are not yet complete, but in a qualitative way they indicate that thickeners between stages of leaching will be satisfactory and that the quantity of silica in a leach liquor moving forward to a new solid has only a minor effect on the quantity of silica extracted from the new solid. A pilot plant is now being designed for operation in the near future to test and evaluate the merits of this process.

Jan 1, 1954

By Samuel Wyer

THE art of natural-gas compressing is now over 25 years old, and has grown at practically the same rate as the increase in domestic natural-gas consumers. There are now over 200 natural-gas compressing stations in North America, aggregating more than 320,000 hp. of compressor capacity and representing a property value of more than $22,000,000, and compressing more than 85 per cent. of all the gas used. The age and magnitude of the art make it evident that the use of gas compressors is a recognized integral part and universal custom of the natural-gas business. The public also is not without its rights and vital interests in this problem. Approximately 1,700,000 domestic natural-gas consumers in North America are dependent upon gas compressors for their natural-gas service. That is, if the use of compressors were to be prohibited, the majority of these consumers would be unable to secure adequate natural-gas service. Each consumer represents between four and five persons, and it therefore follows that the comfort and well-being-as far as natural-gas service is concerned-of at least 8,000,000 persons would be affected if the use of natural-gas compressors should be prohibited. These 1,700,000 consumers have invested, in services, house piping, fixtures, and appliances, an average of about $90 each, or an aggregate of $153,000,000, which is much more than the companies' investment in gas compressors. Furthermore, in all cases where the rate paid by the consumers is fair to the gas company-considering the value of the service rendered by the gas company-the consumers are entitled to continued service and protection of the investment they have made on the faith that the gas service would be continued in the future.

Jan 2, 1916

By Thomas M. Barczak, Claude A. Goode

Principal criteria in the design and operation of longwall mining systems are examined. The decision to apply longwall mining is investigated from an economic viewpoint, and the impact of economics on system design are addressed. Geological considerations and requirements for effective long- wall mining are provided. Ground control factors determining panel design are outlined, as well as environmental considerations. Operational practices are discussed and alternatives recommended. The impact of face moves and the potential for mining wider webs are assessed. Constraints to production are identified and the potential for increasing production of longwall systems is established.

Jan 1, 1982

By R. J. Hafsten, E. S. Davenport, R. A. Grange

THE influence of austenite grain size upon the hardenability of steel is now fairly well understood; for a given austenite, increasing the grain size increases the depth of hardening, and, since the latter is related to the fundamental transformation behavior of austenite, it follows that austenite decomposition must, in general, be retarded by increasing grain size. To date, very little quantitative information bearing directly on the effect of austenite grain size upon the progress and result of isothermal transformation has been published. Davenport and Bain,1 and Zimmerman, Aborn and Bain2 have shown that the transformation is definitely retarded in hypereutectoid plain carbon steels at temperatures near and above the upper region of rapid transformation (Ar') when the austenite grains are increased in size. More recently, Griffiths, Pfeil and Allen3 investigated the effect of a series of different heating (austenitizing) temperatures upon the progress of isothermal transformation at 1245°F. (675°C.) and 745°F. (395°C.) in a medium carbon, low-alloy steel; while they reported no measurements of the austenite grain size, their results suggest that increase in grain size retards austenite transformation at 1245°F. (675°C.), but has no appreciable effect at 745°F (395°C.). The present paper deals with the results of a study of the isothermal transformation of austenite in a single commercial alloy steel in which a fine-grained or a coarse-grained state was induced by appropriate selection of austenitizing temperature. The data are presented in the form of isothermal transformation diagrams, which clearly show that coarsening the grains lessens the rate of transformation of austenite to proeutectoid ferrite and pearlite-that is, at temperature levels above about 1000°F. (540°C.)-but is without significant effect at lower temperatures where the transformation product is bainite or martensite. It is to be presumed that the foregoing statement would be valid, at least in principle, for many other grades of steel; it confirms again that the mechanism of transformation to a pearlitic structure is fundamentally different from that to an acicular structure. A number of related observations were made, which seem to throw some light on the transformation process as it takes place in alloy steels, particularly at temperature levels in the vicinity of 1000°F. (540°C.), where the transition from lamellar to acicular structures occurs. These data are discussed briefly in the belief that they may lead to a clearer understanding of this aspect of the subject. MATERIAL AND EXPERIMENTAL PROCEDURE The material investigated was a commercial grade of S.A.E. 4140 steel, the composition of which was as follows: 0.37 per cent C, 0.77 per cent Mn, 0.98 per cent Cr and 0.21 per cent M0. It was hot-rolled to a 1 1/8-in. round bar and normalized by air-cooling from 1800°F. (980°C.).

Jan 1, 1941

By I. R. Kramer

The stress associated with the high-dislocation layer at the surface of deformed aluminum crystals was measured by progressively polishing the specimen and determining the change in the initial flow stress when the specimen was reloaded. This surface stress increased linearly with strain in the Stage II and Stage III region. The depth to which the high-dislocation layer extends was found to be 0.0025 in. The influence of the surface layer on Stage I is discussed and it is shown that Stage I ends when, on the secondary slip system, the difference between the applied stress and the opposing stress due to the surface layer is equal to the critical resolved shear stress. In previous papers'-3 it was shown that the surface exerts a pronounced effect on the plastic-flow characteristics of metals. For fcc metals it was possible to increase the extent and decrease the slope of Stages I and II and decrease the work-hardening coefficient of Stage II by removing the surface of the specimen continuously during the deformation process.2,3 More recently,L it was shown that the activation energy for plastic deformation and the activated volume were also influenced by the surface. These changes were related to the existence of a high concentration of dislocations in the region near the surface of the deformed specimen and it was concluded' that the effective stress, T, acting on a dislocation was T = Ta-Ti-Ts [1] where 7, is the applied shear stress, Tj is the internal stress, and TS is the stress associated with the surface region containing the high concentration of dislocations. From Eq. [I] it is seen that the effective stress, 7, acting on a dislocation is a function of 7,. Therefore 7, becomes important in any description of the work-hardened state. In this paper the value of 7, as a function of strain and its variation with depth are reported for aluminum single crystals. In particular, it will be shown that the end of Stage I occurs when the net stress, 7, on the secondary slip system is equal to the critical resolved shear stress. To measure Ts, single crystals of aluminum were deformed in tension to various strains, whereupon the load was removed and a known amount of metal was removed by electrolytic polishing. The differ- ence between the final flow stress before the specimen was unloaded and the initial flow stress upon reloading is designated as ?Tp and is the decrease in the stress due to the removal of the surface layer in whole or in part. The value for Tp is taken equal to -Ts. EXPERIMENT PROCEDURE The details of the tensile apparatus, method of electrolytic polishing, and crystal preparation were the same as those used previously,1"3 The single crystals were 1/8 by 1/8 in. in cross section with a 3-in. gage length. The initial purity of the aluminum was 99.997 pet. The specimens were held in vacuo at temperatures 50°C below their melting points for 16 hr and furnace-cooled. Just prior to the application of the tensile stress the specimens were electrolytically polished to remove 0.004 in. from the thickness. This latter operation was conducted after the specimen was placed in the tensile apparatus. The tensile tests were conducted at a strain rate, i, of 10"5 sec-' and a temperature of 3°C. The aluminum crystals used for the determination of 7, are designated A1-3-12 and A1-116. The orientation of the various crystals used throughout the investigation is shown in Fig. 1. The ?Tp values for specimens A1-3-12 as a function of Ax were determined mainly at four strain levels, i.e., ? = 0.0217, 0.0381, 0.0593, and 0.075, where Ax is one half of the total reduction of the thickness after polishing and ? is the re-

Jan 1, 1965

By R. W. Raymond

Edward Cooper was born in New York City, Oct. 26, 1824. His father, Peter Cooper, to say nothing of manifold reasoils for fame as an inventor and philanthropist, deserves to be remembered as a pioneer in the establishment .of public schools ; and it is not surprising that. he sent his son to one of the democratic institutions in which he was himself so ardently interested. From the public school Edward Cooper went to Columbia College, where he made the acquaintance of Abram S. Hewitt, who was first his tutor, afterwards his traveling companion, brother-in-law, business partner and life-long friend.' For twenty years I was the consulting engineer of the firm of Cooper & Hewitt, and also connected with the work of the Cooper Union, in which they were both deeply interested and faithfully active. On the basis of the intimate knowledge thus gained, I venture an estimate of Edward Cooper's character and career which, if not fully comprehensive, may facilitate a juster estimate than would be reached by the student of those data which the modesty of the man permitted to be placed upon public record.

Jan 1, 1907

Discussion of the paper of O. P. Hood, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October, 1914, pp. 2607 to 2611. R. V. Norris, Wilkes-Barre, Pa.-I have had a little experience with gasoline locomotives and I want to indorse very strongly Mr. Hood's point with regard to the danger of carbon monoxide poisoning. I think .the terrible danger is not fully realized. I was foolish enough some time ago, in investigating a gasoline locomotive, to attempt to walk out of the mine entry behind it, and for several days I felt very seriously the carbon monoxide effects. The use of gasoline locomotives ought to be confined to mine entries where there is a very large amount of air. One of the grave dangers is their great convenience and the temptation to run them into chambers for just a few moments to get a car or two. GEORGE S. RICE, Pittsburgh, Pa.-Apparently one of the great dangers is in the style of the gasoline engine. When my attention was. first directed to the type of gasoline locomotives which I saw in the foreign mines-France, Belgium, and Germany, I was most favorably impressed with them, and they have given no trouble on account of fumes, so far as I could learn. Large numbers of them were being used, but all were of small capacity, and of a kind in which the speed control is by a governor of the hit-or-miss type, the engine running continuously. Their power capacity was very low, if I remember correctly it was not over 4 or 5 h.p., but they were used under favorable conditions where the grades in the mines were slight, since the entries or tunnels bad a slight grade in favor of-the load, making about the same pull for the empties against the grade as for the load with the grade. I understand the hit-or-miss valve arrangement enables a setting that will give more perfect combustion than can be insured with the valve controlled by the operating man, as in the automobile type of valve and engine used in this country. Apparently the European type of locomotive does not have the capacity to permit use under the conditions existing in this country, where most of our entries or tunnels have variable grades and long heavy trips of mine cars are used.

Jan 4, 1915

By Richard H. Bube

Photoelectronic radiation detectors may be conveniently classified as homogeneous intrinsic, homogeneom extrinsic, or junction type. Highly photosensitive homogeneous intrinsic photodetectors may be prepared from a number of different II-VI, III-V, or IV materials. Such materials require the presence of specific imperfections that can act as sensitizing centers to provide long majority carrier lifetime. Homogeneous extrinsic photodetectors are of interest primarity for infrared detection, and consist principully of germaniuim and silicon with suitable inpurities. A vaviety of junction photodetectors exist, with silicon us the most common material for them all. The following extrema in performance are found: 1) highest photoconductivity gain in homogeneous intrinsic photodetectors; 2) smallest response time (highest frequency response) in p-i-n junctions; 3) largest gain-bandwidth product in avalanche diodes. ALTHOUGH the total number of materials exhibiting photoconductivity effects is very large, only a relatively few of these have appropriate properties for a practical photoelectronic radiation detector. In fact if one surveys the commercial detectors currently available, one finds that the field is dominated by some ten or fewer materials. These are summarized in Table 1 in terms of the other important variable in detector fabrication, the structure of the material, i.e., whether the material is used as a single crystal or in polycrystalline form, and whether the material is used as a homogeneous detector or whether the detector depends upon the existence of a junction or barrier in the material. The principal wavelength range for each type of material is also shown, together with an indication of the utilization of intrinsic or extrinsic excitation. For the purposes of the present comparison of various detectors, it will be convenient to discuss two main topics: homogeneous photodetectors and junction photodetectors. The performance of a photoelectronic radiation detector is measured in terms of two parameters: the photoconductivity gain, and the response time of the detector. A convenient figure-of-merit is given by the ratio of gain to response time, often called the gain-bandwidth product. The photoconductivity gain is a device parameter since it varies in many cases with the applied voltage and the detector geometry, and should be distinguished from the actual photosensitivity of the material involved. This photosensitivity can be conveniently given as the product of free carrier lifetime and mobility in the material. The photoconductivity gain is defined as the number of charge carriers which pass between the electrodes per second for each photon absorbed per second, where G is the photoconductivity gain, is the pho-tocurrent in amperes, e is the electronic charge in coulombs, and F is the total number of electron-hole pairs created in the photo conductor per second by the absorption of light. The gain may also be expressed as the ratio of the lifetime of a free carrier to the transit time for that carrier, i.e., the time required for the carrier to move between the electrodes. For a material in which one-carrier conductivity dominates, where T is the lifetime of a free carrier, ttr is the transit time for this carrier, p is the carrier mobil-ity, V is the applied voltage, and L is the electrode spacing. From Eq. [2] it follows that the photoconductivity gain is proportional to the photosensitivity of the material (tP), the proportionality constant being The photosensitivity of a material, and hence the photoconductivity gain of a device utilizing the material, depends on the lifetime of the free carriers as a critical parameter. In a homogeneous material this lifetime is determined by the nature of imperfections in the material, and in an inhomogeneous material the lifetime is determined by the specific junction structure. The speed of response, the other basic photodetec-tor parameter, is determined by factors quite similar to those important for photoconductivity gain. Imperfections are of primary importance in homogeneous materials, and the structure of the junction is a determining factor in junction devices. For infrared detectors it has become common to define another quantity designed to indicate directly how effective the detector is in distinguishing between a small photoconductivity signal and random noise due to the detector and its environment. The detectivity D* is given by

Jan 1, 1968

By Bayard Morrow

THE copper-bearing ores concentrated at the Anaconda plant of the Anaconda Copper Mining Co. are principally a mixture of copper and iron sulfides associated in a gangue consisting of quartz, lightly altered granite and feldspars, with sphalerite and galena and more rarely barite and hubnerite as accessory minerals. The predominant sulfide is pyrite. The copper minerals present are: chalcocite, bornite (Erubescite), enargite, chalcopyrite, covellite, tetrahedrite and some tennantite. Normal concentrator practice removes a slime prior to ball-mill grinding. The deslimed ore is ground to approximately 10 per cent plus 65 mesh for flotation. Two selective flotation circuits are used, one for deslimed ore and one for slime. The metallurgical results obtained are shown in Table 1.

Jan 1, 1933

AT THE beginning of February the British Government announced acceptance of the American terms for funding the war debt, the main features-being as follows: Interest rate of 3 per cent. for the first 10 years and then 3 ½ per cent. up to the final extinguishment of the debt at the end of 62 years. The interest from the time since the loans were made to the actual beginning of the funding arrangement to be recomputed at 4 1/4 per cent. instead of the 5 per cent. rate now in effect. Congress ratified the contract respecting the British debt. The ship subsidy bill was relegated to the rear, which is indeed an end to the project. The natural consequence of this will be a liquidation of the Govern-ment's shipping business. The joint committee on the reorganization of Govern-ment departments made its report to the President. In general this seems to offer a well-considered plan for the coordination of Government service. The pro-posals respecting the bureaus that are particularly associated with the mining industry may be subject to criticism. According to the committee's plan, the Geological Survey remains in the Department of the Interior, but the Bureau of Mines and the compilation of the statistics of mineral production are transferred to the Department of Commerce. The Lausanne conference among the European powers came to an end early in February, without any treaty having been signed, owing to the refusal of the Turks to accept the ultimatum of the Allies. Theoreti-cally this left conditions in a state-of war between the Allies and Turkey. However, no actual movements have resulted. The French and Belgians continued to hold the Ruhr district of Westphalia, extending their lines and administration of the region. The Germans adhered to the policy of passive resistance. In the Parliament of Great Britain the French and Belgian policy was plainly declared to be unwise and dangerous. French and Belgian industries, moreover, were troubled by strikes among their own coal miners for higher wages. The Poles and Lithuanians engaged in border war-fare;. the civil war in Ireland continued. The rest of the world was quiet insofar as military operations are concerned.

Jan 2, 1923

By Toyohiko Hirota, Fukuo Itoh

Oil and natural gas aside, sea floor mineral resources currently being exploited in Japan are offshore sand and gravel and deep-sea manganese nodules. The mining of sand and gravel has already started. With regard to manganese nodules, the geophysical investigation and the study of the mining method are also underway. This report outlines the activity of a few Japanese firms, the Deep Ocean Minerals Association formed by some 30 private firms, Government agencies, a public corporation and two government research institutes. Researches on new exploration instruments, properties of deep-sea sediments and the mining method currently conducted by the National Research Institute for Pollution and Resources are described in detail.

Jan 1, 1976

By C. S. Barrett, A. Smigelskas

There have been no publications of the deformation and recrystallization orientations of the metal beryllium, yet pronounced textures would certainly be anticipated since it is close-packed hexagonal in structure. Having an axial ratio approximately that of magnesium, beryllium probably deforms by nearly the same slip and twinning mechanisms that operate in magnesium, and the textures are likely to be similar or but slightly different from the magnesium textures. In the tests reported below this is found to be the case; the textures are found to differ from those of magnesium only in the details of the scatter from the average orientation. This report covers not only samples rolled at room temperature, but some rolled at elevated temperatures. Since magnesium has been suspected by some investigators of altering its crystallo-graphic deformation mechanism at elevated temperatures, it was considered possible that beryllium might do so and alter its textures accordingly. No pronounced alterations were found, however. Unfortunately, the theory of deformation textures is not in a state of development that permits one to deduce the deformation mechanism from a knowledge of the textures, which means that the similarity of textures at different rolling temperatures, reported here, cannot be taken as definite evidence that the deformation mechanism is actually the same at all temperatures. The general similarity of the deformation textures of magnesium and beryllium also extend to the recrystallization textures of the two metals, judging by the pole figures for recrystallized sheet presented in this report. Samples were prepared in the form of composite sheets made up of small pieces stacked in a pile. Each piece was trimmed with scissors so that an edge was parallel to the rolling direction, dipped in paraffin, and assembled into the pack by aligning it under the cross hair of a microscope. As the desired orientation was obtained on each piece it was secured in place by touching with a hot wire to melt the paraffin. A stack of ten or fifteen pieces was built up in this way, then trimmed to the shape of a T; the portion to be X rayed was then etched to the shape of a wire about 0.045 in. diam with 6N HCl. This method of shaping the sample is a modification of that used by Bakarian on magnesium.' The absorption of the rays in the sample was so slight that it caused no difficulty in interpreting the films. Exposures were made with a 0.030 in. diam pinhole, using molybdenum radiation (40 kv, 25 ma, Type A film at 5 cm, 2 to 3 hr exposures). With the recrystallized specimens it was found necessary to oscillate the specimen so as to reduce the spottiness of the lines. A range of oscillation of 5" was SUB- cient to produce reasonably satisfactory patterns, though the quality was somewhat inferior to that of the deformation texture patterns, and only two degrees of intensity were read from the arcs on the films. Typical photo-grams for each of the deformation textures and the recrystallization texture are assembled in Fig 1. The pole figures were plotted in the usual way with the intensity of the various portions of the diffraction rings estimated by eye. Seven to nine films were made of each sample and each was carefully read in plotting the pole figures. Typical series included exposures with the beam normal to the rolling direction and at 11, 26, 41, 56 and 71" to the cross direction, plus two exposures with the beam normal to the cross direction, and at 11 and 79" respectively to the rolling direction. The rolling was in each case considered sufficient to develop the final texture: the reduction by cold rolling was 84 pct (from 0.0045 to 0.0007 in. thickness), following prior hot rolling in longitudinal and transverse directions and recrystallization; the reduction by hot rolling at 800°C was 90 pct (0.010 to 0.001 in.), following similar prior treatment; the reduction by rolling at 350°C was 88 pct (from 0.005 to 0.0006 in.) after similar prior treatment. The recrystallization texture was determined on a sample rolled at 350" to a reduction of 88 pct (0.0165 to 0.002 in.) after similar prior treatment, then mounted between steel strips to keep it flat and annealed at 700" in an atmosphere of argon. Discussion of Results The results of the X ray determinations are assembled in the pole figures of Fig 2, 3, 4 and 5 for rolling at

Jan 1, 1950

[Separates of all the Technical Publications published in 1928 are available at Institute headquarters. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found either in the TRANSACTIONS or in the special volumes issued by the Institute.; METAL MINING TECH- NICAL TRANS. PUBLI- TITLE AUTHOR MEETING VOLUME CATION AND PAGE* No. 50 The Eötvös Torsion Balance D. C. Barton New York Method of Mapping Geologic Feb., 1928 Structure 52 A Cartographic Correction for the C. A. Heiland New York Eötvös Torsion Balance Feb., 1928 61 Liquid-oxygen Blasting at Chuqui- H. C. Schultz, New York camata, Chile F. K. Middleton Hunter Feb., 1928 76, 108, 123 64 Working Methods of Practical Geo- Hans Haalck New York physics Feb., 1928 65 Experiments with Eötvös Torsion P. W. George New York Balance in the Tri-State Zinc and Feb., 1928 Lead District 74 Gravity Surveying in Great Britain H. Shaw New York Feb., 1928 75 The Computation of Eötvös Gravity E. Lancaster-Jones New York Effects Feb., 1928 82 Earth-resistivity Measurements in W. O. Hotchkiss, New York the Lake Superior Copper Country W. J. Rooney, Feb., 1928 James Fisher 83 Mining Methods and Records at the Roy W. Moore New York 76, 56, 90 United Eastern Mine Feb., 1928 98 Recent Results in Electrical Pros- Hans Lundberg New York specting for Ore Feb., 1928 101 Relation between the Oxygen Bal- G. St. J. Perrott, New York ance and Propulsive Strength of N. A. Tolch, Feb., 1928 Eight Gelatin Dynamites J. E. Crawshaw 102 Effect of Oxygen Balance of Gelatin G. W. Jones, New York Dynamites on the Gaseous Prod- G. St. J. Perrott Feb., 1928 ucts of Detonation 108 The Financial Report of a Min- Henry B. Fernald New York ing Company-Its Content and Feb., 1928 Meaning 116 What Duty to Support the Surface R. G. Bosworth New York Does a Subsurface Owner Owe? Feb., 1927 136 Comparison of Branch Raise and C. A. Mitke Los Angeles 76, 93, 103 Combined Shrinkage and Caving Sept., 1928 Methods 141 A Mining Company Balance Sheet G. F. Wolff New York Feb., 1928

Jan 1, 1927

By T. G. Fulmor, William Wraith

What impelled The Anaconda Company to dismantle and move a concentrator 25 miles that was already operating at a rate of 35,000 ton per day? The answer to that question takes in almost exactly 49 years and perhaps 10 complete cycles of the metallurgical wheel in the Anaconda, Mont., mill. One could say with truth that the move is a logical next-step in the development of metallurgy in The Anaconda Co. In the old concentrator at Anaconda, the background story is unfolded: - Gravity separation by jigs, later supplemented with gravity tables, 1905. - Separate sand and slime froth flotation, 1915. - Acid bulk froth flotation, 1917. - Bulk alkaline flotation, 1926. - Alkaline flotation of total ore without sand- slime separation due to change in ore type. 1939.

Jan 5, 1964

By W. H. Coghill, A. M. Gow, M. Guggenheim, A. B. Campbell

The object of this paper is to discuss the fundamental principles of ball milling and to present some observations which have been made in laboratory and plant investigations. The discussion will be limited to wet grinding of ores in cylindrical mills, but doubtless many of the principles involved will be equally applicable in the other fields of fine grinding in which mills of the same type are used. In the concentrators of the United States there are about 650 ball, rod, or pebble mills, operating or ready to operate, and these have about 100,000 connected horsepower. For grinding in cement plants there is about three times this connected horsepower, and other industries have an unestimated amount, all used for the general type of grinding that is to be discussed here. It is true that these figures do not represent stupendous amounts of power, but when one considers that ball milling is often the ((bottle neck" in a concentrator and that it often accounts for the largest single item in the cost sheet, the importance of a comprehensive understanding of the principles of ball milling can be appreciated. Much of the past literature devoted to the subject has been concerned with the Kick-Rittinger dispute over evaluating grinding, or with dissertations on ball paths and the closely allied impact versus attrition hypotheses, or with the exclusive consideration of certain specific variables, such as mill speed or circulating load, irrespective of the other factors in operation. Such subjects may be dismissed with but little discussion in what may be called, by comparison, a new philosophy in the study of ball milling. Briefly, this '(new philosophy" consists of using power as an index of the mill operation, and investigating grinding from the standpoint of set and induced varisbles, with emphasis on the latter.

Jan 1, 1935

By C. Grua, M. Gottlieb, E. M. Wewerka

The Purpose of this paper is to present an overview of research underway at the Los Alamos Scientific Laboratory to investigate some of the more attractive options for controlling trace element contamination of coal refuse drainages. * The control methods under consideration include chemical and physical methods to immobilize or remove undesirable contaminants prior to refuse disposal, the treatment of refuse disposal sites with attenuating agents to prevent the discharge of contaminated water, and the direct treatment of refuse drainage as it emerges from the refuse disposal site. The results from these laboratory studies suggest that many of these techniques are technically feasible for controlling trace element contamination of refuse dump drainage.

Jan 1, 1982