Search Documents

By Allan Martin, R. A. Swalin

Diffusion rates of manganese, aluminum, titanium, and tungsten in nickel were measured at temperatures between 1100° and 1300°C. Activation energies, Q, and values of the frequency factor, Do, were calculated for each system. Values of Q were found to be within 15 pet of that for self-diffusion of nickel in agreement with present theories of diffusion. ONE of the most interesting problems in diffusion concerns factors governing the order of diffusion coefficients of various solutes in a common solvent metal at low solute concentrations. An early suggestion by Rhines and Mehl' was that diffusion coefficients might each approach that of the self-diffusion coefficient of the solvent itself. Later Thomas and Birchenall' pointed out correlations between the order of the diffusion coefficients and the freezing point depressions of the solvent by the various solutes. Other correlations have been sought. To settle this question it seems likely that much more data will be needed and, in particular, data collected at low solute concentrations. This type can be obtained by special analytical techniques as well as by use of radioactive tracers. The following study was made of diffusion of manganese, aluminum, titanium, and tungsten in a common solvent, nickel, at relatively low solute concentrations: 1—Production of alloys of nickel with manganese, aluminum, titanium. and tungsten at concentrations of the order of 1 atomic pet. 2—Use of pressure-welded diffusion couples in cylindrical form. 3—Diffusion anneals in the temperature range of 1100" to 1300°C. 4—Lathe sectioning of the diffused couples. 5—Spectrophotometric analyses of lathe turnings for the solute being studied. 6—Calculation of the diffusion coefficient for each of the solutes as a function of temperature. 7—Interpretation of results with current theories of diffusion. Experimental Work Materials—Two types of nickel were used in this research. The grade designated as Vacuum melted Mond nickel was used for all diffusion systems except the Mn-Ni system for which the Vacuum melted electrolytic nickel was used. Analyses of the two grades are given in Table I. The manganese used in making alloys was 99.9 + pet pure, aluminum 99.99 pet pure, titanium 99.9 pet pure, and tungsten of C.P. grade powder. Alloys used in this investigation were prepared by melting in vacuo or under a low pressure of argon. After melting, all heats except those of nickel-manganese were poured into a cylindrical copper mold 3 in. long and 1 in. ID. In the case of nickel-manganese, the alloys were solidified in the melting crucible. For nickel-aluminum heats alumina crucibles were used and for all other heats, zirconia crucibles.

Jan 1, 1957

By H. Landsberg

In a previous report1 it was pointed out that a successful attack on roof troubles has to be preceded by extensive scouting. As Lord Kelvin once said, scientific progress can be made only if accurate data are available: "unless you measure, you do not know." The Convergence Recorder For the observation of roof movements in mines the convergence recorder has shown that it will enable us to get some of the necessary information. Results with convergence recorders were first published by Winstanley and other English investigators for rapidly moving longwall faces. In their investigations the speed of work and the heavy overburden produced a considerable amount of absolute values of convergence in a short time. Under the conditions frequently encountered in our investigations in Central Pennsylvania, under shallow, overburden and in mines with slowly proceeding extraction, the movements observed were much less in absolute value, for an equal interval of time. This mas partly because the mines in which our studies were carried on frequently had idle days, sometimes four or five in succession. Therefore continuous records were not employed and a simple convergence gauge was built. In its first models, it consisted only of two telescoping tubes pressed against roof and floor by a coil spring. At the side of the lower tube a rule divided into 1/2-mm. divisions mas fixed and a knife-edge, which was attached to the upper tube, mas slid over the scale in case of convergence between roof and floor. While the larger motions could be read on this device, it seemed to be desirable to increase the accuracy by inserting between the two tubes a dial meter reading in 1/1000 in. Such a gauge was first built in April 1937 and installed for experimental purposes in a bituminous coal mine in Pennsylvania (Fig. I). It was read at least once daily, 24 hr. apart, and if feasible at shorter intervals. After several months of experience it can be said that this type of gauge answers the scientific as well as the practical needs. It is easier to handle than the recorder; no clock is used, there are no pen troubles. The price of

Jan 1, 1938

By Frank G. Miller, Ralph A. Seban

Problems relating to thermal methods of oil recovery have been given increasing attention during the past year. The nature of the physical and chemical processes underlying thermal recovery are not yet well understood. The need for pertinent basic information is recognized generally. One of the processes involved is the transfer of heat by conduction in oil reservoir rocks containing moving reservoir fluids. This technical note deals with heat conduction in a laboratory sand column filled with a moving hydrocarbon and therefore should be contributory to the presently inadequate fund of knowledge on thc over-all subject. In an analysis of the flow of vaporiziny propane through a horizontal column of sand, one of the present author9 demonstrated correspondence between thc measured values of pressure along the length of the column and those predicted by a theory which postulated that the enthalpy of the propane was invariable along the length of the column. This postulate way implied as a deduction from the principle of conservation of energy but the details of the deduction were not given. The specific purpose of this technical note is the presentation of these details both as an adjunct to the earlier analysis and to supply some additional details on the processes involved in this type of flow. Results disclose that rates of heat transfer by conduction, in the direction of fluid motion, generally would be small for systems of the type studied. FUNDARIENrAI. ENERGY EiQUAI-[ON The principle of conservation of energy may be applied to a section of the porous material on the basis that heat transfer, like fluid flow, is possible in the x direction only. Transfer of heat in the y and z di'rections is prevented by suitable insulation or by taking the medium as infinite in directions perpendicular to the x axis. For steady state heat conduction and conditions of steady fluid flow the principle of conservation of energy specifies that any reduction in the enthalpy rate increases the flow of heat in the same proportion. Stated mathematically, dH KA 87 —- = - — - — U) * dx W dx........ Lvhere is the flow of heat in the positive x W dx direction. TEMPERATURE DISTRIBUTION IN DIRECTION OF FLOW The column of sand used in the previoi~sly described research is divisible into three different flow regimes. each of which may be analyzed independently. In the entrance region the liquid approaches the saturation state. A transition region is postulated following the transverse section at which the saturation state of the liquid is attained. In this transition region gas and liquid phases are both envisioned as present, with no vaporization occurring and with fluid movement restricted to the liquid. The upstream end of the exit region is at the transverse section of the column where the fraction of the pore space occupied by gas first becomes great enough for gas flow and where vaporization of the liquid begins. Fig. 1 indicates schematicaHy the thermodynamic processes undergone hv the fluid in the three flow regimes.

Jan 1, 1956

Jan 1, 1920

By K. H. Hiller

A rotational viscometer has been designed which perrnits the measurement of the rheological properties of drilling muds and other non-Newtonian fluids under conditions equivalent to those in a deep borehole (350F, 10,000 psi). The important mechanical features of this instrument are described, and its design criteria are discussed. The flow equations for the novel configuration of the viscometer are derived and the calibration procedures are described. The data and their interpretation, resulting from measurement of the flow properties and static gel strengths of homoionic montmorillonite suspensiom at high temperatures and pressures, are presented. Data are also presented for the flow behavier of typical drilling fluids at high temperatures and pressures. The pressure losses in the drill pipe and the annulus depend critically upon the flow parameters of the drilling fluid. This work demonstrates the need to measure these parameters under bottom-hole conditions in order to obtain a reliable estimate of the pressure losses in the mud system. INTRODUCTION The rheological properties of drilling fluids are affected by temperature and pressure, but the extent of these effects on the dynamic flow properties is not well known. Measurements of changes of the flow properties of clay-water drilling muds with temperature have been reported by Srini-Vasan and Gatlin.1 The temperatures reported did not exceed 200F, a limitation imposed by the apparatus used by these authors. The rheological properties of clay suspensions were measured at temperatures up to 100C by Gurdzhinian.' Neither the nature of the exchange ions in the clay suspensions nor the degree of purity were defined in his work, nor were the measurements extended to currently used drilling fluids. The lack of systematic measurements of dynamic flow properties at high temperatures and pressures seems the more surprising since during the last decade the importance of the control of the hydraulic properties of drilling fluids has come to be widely recognized. Very good mathematical treatments of the friction losses in drill pipe and annulus have been developed.3 4 These treatments are based on the assumption that drilling fluids behave as Bingham plastic fluids. Quite often this assumption is justified, while in other cases a power law equation pro- duces better fit than the Bingham model does. For convenience in applying viscometer data to pressure-drop calculations, the Bingham plastic flow equation is preferable and, therefore, has been applied to the data reported in this paper, although other equations may fit these data more accurately. In a Bingham plastic fluid the relationship between the shearing stress 7 and the rate of shear D is given by the following equation: where is the plastic viscosity and 4 the yield point. If 4 = 0, the equation for simple Newtonian flow, 7 = pD, is obtained. Two empirical constants are required for the description of laminar flow of a Bingham plastic fluid, and calculations of the flow behavior at high temperatures and pressures cannot be better than is permitted by the accuracy with which these constants are known. For this reason a high-pressure, high-temperature rhe-ometer has been designed to measure the plastic viscosity the yield point +, and the static gel strength S, at pressures up to 10,000 psi and temperatures up to 350F. The important features of its design will be described. The results of measurements on homoionic clay slurries will be discussed insofar as they are relevant to an understanding of the general flow behavior of clay-water drilling fluids. The results of measurements on some typical drilling fluids will be presented also, and their practical implications will be briefly discussed. DESCRIPTION OF EQUIPMENT MECHANICAL FEATURES A viscometer designed to measure the plastic viscosity, yield point and gel strength of non-Newtonian fluids must permit the measurement of the shearing stress t at any given rate of shear D. This is possible only if t and D are approximately uniform throughout the entire sheared sample. A Couette apparatus is the most convenient method of realizing this condition, as has been pointed out by Grodde." The "high-pressure, high-temperature rheometer" described in this paper is basically a rotational Couette viscometer that is immersed in a cell in which pressure and temperature can be controlled over the range of interest. Fig. 1 shows schematically the important features of the pressure cell and associated equipment. The heart of the instrument is the rotating cup. It is shown more clearly in Fie. 2. which revresents the lower one-third of the pressure cell (below the input drive shaft shown in Fig. 1), and it is shown in detail in Fig. 3. For measurements of dynamic flow properties, the rotating cup is driven by a 1/2-hp electric motor, which operates through a Vickers

[ ]

Jan 1, 1907

By John G. Bartram

The oil business has been relatively quiet in Wyoming during 1934. Only 34 producing wells were completed, 54 dry holes were drilled, and at the end of the year only 30 wells are listed as drilling. Wyoming still has a large reserve of production shut in, mostly in black oil or asphaltic base fields in the northwestern part of the state. The total oil production increased from 11,171,500 bbl. in 1933 to 12,539,470 in 1934, but light oil production continued to decline, and the increase was made by black oil fields. This is partly due to natural decline of light oil fields, especially Salt Creek, Big Muddy and Lost Soldier, but largely because of increased demands for road oil. The Rocky Mountain states spent much money to build and improve roads and a greater amount of road oil was used. The refining of black oil to manufacture road oil produced gasoline as a byproduct that slightly decreased the demand for light oil. The Oregon Basin and Frannie fields, in the Big Horn Basin, moved into second and third places in the list of producing fields in Wyoming because of their increased black oil production, and Big Muddy and Lost Soldier, light oil fields, dropped back. Wyoming stayed close to its allowed production, which was based on the needs of the refiners and purchasers. This activity in black oil resulted in a few more wells in the fields of the Big Horn Basin, but the greatest amount of drilling was in the shallow Osage field in eastern Wyoming. Osage supplies many little topping plants and at the close of 1934 there was not enough oil available there to supply all of them. In the Lost Soldier field and Salt Creek, one major company was rather active in a campaign to deepen, clean out and repair old wells to increase production, and the figures of that work are not included here. Of the light oil fields, Lance Creek promises to be most active during 1935, since the two wells in the recently discovered Sundance sand pool are producing and more wells will he drilled. With wildcatting almost at a standstill, two new oil fields were discovered in Wyoming in 1934. In Albany County, a 75-bbl. oil well was completed on Quealey dome in the Muddy sand (Upper Cretaceous)

Jan 1, 1935

By Shun-ichi Satoh

THE electric arc welding of cast iron has been studied by Braune, Lamberton, Schimpke, Kenyon, Gale Manufacturing Co., Wedemeyer, Candy, Neese, Miller, Carter, American Welding Society, Namack, Lebrun, Achenbach, Jansson, Kochendörffer and others.1 The writer of this paper has been able to obtain a series of cast irons, from gray to white, without using cast-iron electrodes but by coating on wrought-iron bars mixtures of carborundum (SiC) and graphite (C). In this work, he has found the curious phenomenon of barium- carbonate.

Jan 1, 1929

By Frank Firmstone

IT is often desirable to obtain one or more accurate horizontal sections of a blast furnace after blowing out. Wishing to do this, last April, in the case of No. 4 furnace at Glendon, which had worn in a very remarkable manner, the method described below was employed, with very good results. A scaffold was fixed in the furnace, and on it was placed a drawing- board, covered with paper, the top of which was made level at exactly the height at which the section was to he taken. (Fig. 8.) The centre of the furnace (which had previously been found, and marked on a plank across the top) was laid off on it by dropping a plumb-bob from above, and a strong needle was driven into the board in the centre. By means of a straight-edge and two plumb- bobs, the line passing through the centres of the front and back arches was also drawn on the board. A pencil was fastened to a light wooden straight-edge at a known

Jan 1, 1875

By J. P. Dovel

Having been requested to prepare a paper referring especially to my patents as applied to blast furnaces, I shall confine my discussion to those improvements and inventions pertaining directly to the blast furnace itself, omitting a number of patents pertaining to blast furnace operations. I spent the early part of my life in the construction of blast furnaces, from rivet-heating to drafting and designing, much of the work relating to repairs and rebuilding. Later, as I became more interested in maintenance and operation of a group of blast furnaces, one fact especially made a lasting impression on me; namely, that a very expensive piece of equipment was very short lived, and the expense of replacement, relining, etc., in many instances consumed most of the profits made while in actual operation. As far back as 1910, I began to lay plans to build with a view to permanency and not merely for a blast, the common expression at that time, which really meant only one or two years in southern practice. Since we did not then blow so hard most failures occurred in the bosh and hearth. The failure of either generally meant a complete new lining, as the inwall did not look good enough to last another blast. At that time we were using two types of hearth, one of heavy steel plate protected by well and sprays on the outside, and one of heavy cast iron, made in sections and bound together with wrought-iron bands. The former type proved dangerous, for if the iron should come through, as it frequently did, it would cut away the steel plate, quickly turning large quantities of molten iron into the water, causing a severe explosion and costly repairs. The cast-iron type gave trouble also by the iron finding its way through the joints between the sections, which was not so serious, since the iron would not cut a way the heavy cast-iron sections very quickly, and generally caused only small damage, and repairs were easily made. Both types have been improved; the former by the introduction of cast-iron water-cooled plates, placed on the inside of the steel jacket. This has proved to be very good construction, but has no real claim to permanency. As the cast-iron plates cannot be replaced from the outside, the operator must assume that some time, at no late date, he must replace them from the inside, which will mean a blowing out of the furnace. The heavy cast-iron hearth has been improved by making the

By G. K. Manning, E. R. Stein, E. E. Underwood

Columbium, carbon. and nickel additions were made to iron-base alloys with 20 pct CY. The effects on microstructure, precipitation-hardening characteristics, and High-temperature properties were investigated by means of metallographic, hot-hardness, and magnetic measurements. An austenitic alloy consistilzg of Fe-20Cr-14Ni-0.8C-2.5Cb had higher hot-lzaciness at 1700°F than the other alloys investigated. Its favorable standing is attributed to an enhanced interaction of Cb and Cr4C particles dispersed within a stable austenitic matrix. FOR the past 20 years, cobalt- and nickel-base alloys have been used for the more stringent high-temperature applications because of their excellent creep resistance. Although their performance is quite satisfactory, other base materials must be considered for large tonnage, low-cost applications such as for the automotive gas turbine. Iron-base alloys are also used extensively, but at somewhat lower temperatures, primarily because of the instability of particles or because precipitation occurs at relatively low temperatures. Since unusual stability has been reported for Fe-Cb and Cb-C compounds.1-3 it was hoped that effective amounts of these compounds could be taken into solution at temperatures just below the melting range, then precipitated upon reheating. Actually, strengthening was found to occur by both precipitation hardening in some alloys and by phase transformations in others. Among the alloys investigated, that with the best high-temperature properties owes its strengthening to a combination of carbide particle interaction and a relatively stable austenitic matrix. EXPERIMENTAL PROCEDURES Small preliminary melts of about 100 g were made in a vertical Glotube furnace, using alundum crucibles and an argon atmosphere. Alloys weighing 35 lb were melted in a basic-lined induction furnace, also under argon. The compositions of the alloys are given in Table I. The nickel-free alloys were usually ferritic, while those containing nickel were generally austenitic. Depending upon the particular heat treatments, or the combination of alloying elements, two-phase alloys of ferrite and austenite could be obtained. In the following text, however, the nickel-free or nickel-bearing alloys are referred to simply as either ferritic or austenitic alloys respectively. The small ingots were swaged at 2000°F, in steps, to rods of approximately 3/16-in. diam. The large ingots were forged at 2100°F to 1-in. sq bars. No difficulties were encountered in swaging or forging any of the alloys to as much as 90 pct reduction in area. For heat treating at temperatures above 2000°F, specimens were sealed in quartz tubes under a partial pressure of helium. No special precautions were found to be necessary at lower temperatures. Intermetallic compounds in the preliminary alloys were identified by means of X-ray diffraction measurements. Correlation of these results with micro-structural characteristics (such as color, shape, size, and location) of the compounds aided in their identification. Magnetic susceptibilities were also obtained at room temperature with a Magne Gage instrument after the various heat treatments. To

Jan 1, 1962

By G. D. Just

INTRODUCTION Large scale underground mining involves the bulk handling of fragmented material. The cost and efficiency of the mining systems is there- fore significantly influenced by material flow characteristics. Flow problems may occur in the form of ore pass blockages which interrupt the free flow at extraction openings. The costs of such delays can be readily assessed and compared to the costs incurred in reducing blockages by improved fragmentation or larger ore passes. In practice the problem is more complex than this statement suggests because it is generally un- economic to design for zero ore blockages. Another major flow problem occurs in the form of relative movement of ore and waste as the fragmented material is extracted. This produces waste dilution in the recovered ore and influences total ore recovery. This flow problem is much more complex than the ore block- age phenomena. Many questions concerning the precise flow characteristics remain unanswered because of the variability of size distributions, particle shapes, material properties and the total extraction layout and design. Model studies can provide a visual and quantitative illustration of probable flow characteristics but full scale data collection is necessary to evaluate the precision of such information. The methods and types of data obtained must be carefully selected to recover the maximum volume of useful information for operational control and future design. It is essential that honest precision levels are assigned to the data and any subsequent analyses. Grade control data may give misleading short term information on flow characteristics because of the difficulty in knowing the true grade of the mass of material before extraction commences. However, in the long term control of extraction grades is vital to the profitable operation of the mining system. The most efficient extraction design and operational schedule can only be determined after all of the facts and variables are known. This is usually only possible after the orebody has been completely extracted. However, if design and operational personnel have a full appreciation of the nature and variability of material flow under different conditions the best possible results should be achieved. The most significant features of material flow are out- lined in this paper in order to provide mine planning and mine management personnel with some of the necessary information relating to material flow. Available facts and reliable figures from selected publications are noted in association with unbiased and hopefully accurate opinions of the relevance of the data to mine design and mine system control. Possible future developments and profitable areas for research into material flow problems are also detailed. MATERIAL FLOW AND MINING METHODS The effects of material flow on the design and operation of an integrated underground ore handling system is one factor which is common to most mining methods. Analysis of the system as detailed by Just, 1980, permits the identification of unit process objectives. For example, a typical underground ore handling system as illustrated in Figure 1, involves the following unit operations:- (i) Gravity flow of ore in stope (ii) Ore extraction at base of stope (iii) Ore haulage on the production level (iv) Dumping of ore into ore pass system (v) Gravity flow of ore in the ore pass (vi) Underground crushing of ore (vii) Haulage of crushed ore to shaft (viii) Hoisting of ore to the surface. Average flow rates in each of these unit operations can be misleading due to variability in incremental capacity caused by flow blockages and machine delays. Thus to effectively analyse the probable performance of the system, it is necessary to have a measure of the flow loading and haulage rate variability. Mechanical equipment performance specifications can be used to provide such information for loading, haulage and crushing; however, in the case of the gravity flow of material field measurements are required to relate the probability of "hang-ups" to the degree of fragmentation. Factors affecting the frequency of flow stoppages are, size, distribution and cohesiveness of broken material and the geometry and size of the flow channel. Ore pass channel design is relatively simple since regular cross-sectional shapes are used

Jan 1, 1981

By Luis A. Fierino, M. Ashraf Mahtab

This paper reviews the background of, and solution techniques for, the major geomechanics problems affecting caving operations, including prediction of cavability, defining size distribution of or fragments, stability and support of production openings, and control of rock bursts and subsidence. Further research is also suggested in the solution of the various geomechanics problems.

Jan 1, 1984

By H. De Cizancourt

France.—Pechelbronn remains about the only producing field, 41 per cent of the 1937 output of 496,525 bbl. being mined by shaft and 59 per cent produced from pumping wells. At present Gabian has only a very small production. During 1937 there was no private undertaking for petroleum research. Only the Office National des Combustibles Liquides has done any drilling, unsuccessfully, at Pezenas and Frangy-Chilly. Algeria.—No new research has been made and Tliouanet, a small acreage pool that has been declining for several years, gave only 2193 bbl. in 1937. Morocco.—The SociCt6 Chhrifienne des Petroles continues active work. First tests of production made on the Jurassic structures of the Tselfat and Bou Draa must be mentioned for 1937. In connection with these tests, which have yielded 16,495 bbl., 14 new wells have been located

Jan 1, 1938

G. McMEANS*—This paper is a very good demonstration of the use of a new tool for the solution of industrial problems of a physical nature. To have solved this problem without the use of radioactive tracers would have required a far greater amount of investigation and work. The authors have described their work in such detail and in such a manner as to suggest the possibilities of the use of such tracer studies in the solution of many perplexing problems of industry. R. E. BREWER †—The authors are to be congratulated on this very excellent paper, which describes the results obtained by utilizing radioactive tracers in investigating the complicated reactions in the coking process. The paper has especial merit because the study was made under typical operating conditions in a commercial coke oven. Considering all the difficulties involved, the results obtained are excellent. My brief comments will relate primarily to the method used for determining the sulphur in the gas and to the value of the data obtained in stimulating further research. In discussing their results, the authors state (p. 17) that "Of the total sulphur charged to the oven in the coal 95 pct was accounted for in the coke and gas. Most of the sulphur unaccounted for is believed to have been lost in the gas, since the gas sampling system removed all the H2S but probably only part of the organic sulphur compounds present in the gas. Although sulphur in the acid-insoluble tar residue in the gas scrubbing bottles was determined and added to the total sulphur determination of each sample, it is doubtful whether an aliquot portion of tar for each sample was obtained." The reviewer believes that the authors might have obtained a better sulphur balance had they used an improved procedure for determining sulphur in the gas. The absorption train should have included a trap to remove the tar and am-moniacal liquor and a wash bottle containing 5 pct sulphuric acid to remove ammonia in the coke-oven gas before it entered the gas scrubbing bottles containing the ammoniacal cadmium chloride solution. Sulphur in the tar and

Jan 1, 1950

By William H. Emmons

Jan 1, 1912

By H. I. Aaronson

Isothermally formed plates of proeutectoid a, lengthen at approximately the rates predicted by the Zener-Hillert equation, indicating that their lengthening kinetics are controlled by the volume diffusion of chromium in the ß matrix. Solution annealing treatments in the vicinity of the transus introduce a second mode of transformation, in which the lengthening rate is at least 1.8 x 104 faster than predicted by this equation. Little or no volume diffusion appears to accompany the latter transformation. The Presence of oxygen is evidently a Prerequisite for the occurrence of this reaction. X HE effects of thermal history prior to the initiation of transformations which proceed by nucleation and diffusional growth are currently evoking considerable interest. The rate of nucleation (but not the rates of growth) of pearlitel and of bainite,2 and the over-all rates of aging reactions in Al-cu3 and Al-si4 alloys have been shown to be appreciably dependent upon thermal history in the solid-solution region"' or in the two-phase region prior to the onset of pre~ipitation.3,4 In none of these reactions, however, was the transformation mechanism changed by variations in the temperature-time path used to reach the reaction temperature. Preliminary experiments reported by M. K. McQuillan5,8 and a systematic investigation by Farrar and Margolin7 have disclosed that the transformation behavior of hypoeutectoid Ti-Cr alloys is considerably more sensitive to thermal history. Qualitative evidence strongly suggests that not only the rate of nucleation but also the rate of growth and even the mechanism of the ß — a reaction can undergo remarkable changes when a solution annealing treatment in the vicinity of the ß/a +ß, or transus temperature, is interposed between a high-temperature solution anneal (conventionallq at 1000°C) and the isothermal reaction treatment. The present investigation was undertaken in an attempt to ascertain the nature and origin of these effects. Study of the changes in the kinetics and morphology of the ß - a, reaction produced by varialtions in thermal history was the primary means employed for this purpose. EXPERIMENTAL PROCEDURE The compositions of the alloys used in this in~esti~ation are given in Table I. These alloys were homogenized for 5 days at 1050° C in evacuated (2 x 10 -5 mm of Hg), zirconium-gettered fused quartz capsules. The capsules themselves were enclosed in a porcelain chamber evacuated with a mechanical pump during the homogenization anneals. Upon completion of homogenization, the alloys were cooled to room temperature and then reheated to 550°C for 3 1/2 days in order to transform the alloys to a finely divided mixture of a and TiCr2, and thus provide an approximately constant initial mi-crostructure. Individual specimens were sealed in evacuated and internally gettered Vycor capsules and heat treated as previously described.8,9 EXPERIMENTAL RESULTS Ti-10.64 Pet Cr. This investigation was largely performed on the 0.64 pet Cr alloy. The "base"

Jan 1, 1962

By Theodore Barry

The task of developing controls in the mining and manufacturing industries to give them a tighter grip on operating costs has afforded this author an interesting vantage point for observing certain practices common to both industries. Of course, each of these industries has problems unique to itself, but all industries have many common problems. After all, every industry is a business and every business is concerned with the task of producing its wares as profitably as possible. While many differences between businesses in different industries are known, the author is convinced through experience that the mining industry has much more in common with the manufacturing industry than is generally acknowledged. Four principal questions come to mind in the comparison of mining with manufacturing: How different are the management control methods in these two worlds? How do both industries go about the task of controlling costs? How does the mining industry compare in terms of the effectiveness of its workers? And perhaps most important, what can the mining industry learn from what the manufacturing industry is doing?

Jan 11, 1962

By J. Moore, D. Gault, R. V. Lugn

Impact of small projectiles with velocities between 0.9 and 7.3 km per sec on basalt produce craters chiefly by the ejection of fragments. Weight-size distributions of the ejecta are linear for part of the size range of the fragments. Cumulative weight-size distributions of the ejecta from different craters vary because of erratic formation of large fragments and a large percentage of ejecta below 0.1 mm. In the range of velocities studied, the crater depth is approximately proportional to the 0.75 power of velocity of the projectile. This relationship may represent a transition regime between the fluid impact regime and the undeformed projectile impact regime. The volumes per unit of projectile energy of the craters produced are comparable to those reported for lower speed projectile impact and drill bits. An experimental investigation of projectile impact on rock is being conducted jointly by the Ames Research Center of the National Aeronautics and Space Administration and the U.S. Geological Survey. Projectiles are launched with light-gas guns at the Ballistics Range of the Ames Research Center. The craters and ejecta produced in these experiments are being studied by the U.S. Geological Survey. Steel, aluminum and polyethylene projectiles weighing from 0.25 to 0.015 g were accelerated to velocities of 0.88 km per sec (2,900 fps) to 7.3 km per sec (24,000 fps) with a light-gas gun, using hydrogen as the propellant medium. Projectiles impacted the targets normal to plane rock surfaces in an atmosphere of air with a nominal pressure of 25 to 50 mm of mercury. The metal projectiles were mounted in supporting four-piece nylon sabots, which guided the projectiles down the launching tube. After launch, aerodynamic drag acted to separate the sabots from the projectiles. Impact velocities were determined with time measurements and spark photographs of the projectiles in flight. Ejecta were collected in lucite and aluminum containers placed around the target block. A small hole in the containers permitted projectile entry. Impact of projectiles of the size employed produced craters in the rock targets chiefly by ejection of fragments. The craters are small, roughly conical depressions with crushed and intensely fractured rock at the bottoms of the depressions. The ejecta are composed of pieces of the projectile and rock fragments ranging in size from a few tenths of a micron or less to several centimeters in maximum dimension. In this paper, the structural features of the craters, the weight-size distributions of the recovered ejecta, and crater depth and crater volume relationships are described. DESCRIPTION OF CRATERS Typical craters (Fig. 1) produced by experimental projectile impact in basalt are shallow, wide base

Jan 1, 1963

By M. K. Foster

Ten horizontal retort zinc blocks of a modified Hegeler design are in operation at Nueva Rosita, Coahuila, Mexico, and produce approximately 170 t of spelter daily, or 62 000 t/year. A block consists of two furnaces of 448 retorts each, making 8960 retorts as the plant complement. Each furnace block is fired with natural gas and air maintaining the combustion mixture in the furnace always slightly reducing. No attempt to recover energy through waste heat boilers is made. The spelter moves to market by rail and truck either in palletized bundles weighing approximately 1060 kg, as loose slabs weighing 26.5 kg each, or as 1088 kg ingots. At present 46% of the metal is exported and 54% is consumed domestically in Mexico. The present day trend toward equalized or alloyed spelter, as well as special shaped castings results in sales of 35% of the entire plant's production. Sulfuric acid is also produced by the Contact Process using vanadium pentoxide as the catalyst. The plant is basically a Monsanto contact system, producing approximately 68 t of 100% sulfuric acid daily. Both 98.5% sulfuric acid and 20% oleum are available. All of the acid made is consumed in Mexico. Shipments are made in 26,900 dm3 tank cars.

Jan 1, 1970