Search Documents

By C. S. Barrett, D. B. Masson

Martensitic transformations have been found in AgCd both upon cold-working at room temperature and cooling to lower temperatures. The crystal structures of the transformation products were found to be close-packed hexagonal in the first case and or-thorhombic in the latter. The transformation characteristics also were studied. Similar treatment of AuZn alloys failed to yield any transformation. THE literature on martensitic transformations of body-centered cubic metals and alloys indicates widespread instability of this structure at low temperatures, a tendency which merits further study. The body-centered cubic ß-phase of CuZn, for example, when it contained less than 42 wt pct Zn, was found by Greninger and Mooradian' and others' to transform on cooling to subzero temperatures to a phase that was tentatively considered to be tetragonal. Further work by Massalski and Barrett" demonstrated that cold work at low temperatures causes a partial transformation of ß CuZn of higher Zn content. The structures of the strain-induced transformation products were found to be different from those induced by simple cooling. Another well-known martensitic transformation among body-centered cubic phases is that of ß AuCd, first studied with X-rays by Olander,' then very thoroughly by Chang and Read.5,6 Here again transformation was found to occur both as a result of cooling and of strain. The alkali metals Li and Na, as well as certain Li-Mg alloys, also undergo transformation from their normal body-centered cubic structure, both on cooling and on cold-working. The phase AgCd, the subject of the present report, should be expected to behave quite similarly to CuZn for a number of reasons. It is the chemical analogue of CuZn, silver being directly below copper and cadmium directly below zinc in the periodic table. The size factors (percent difference in size) of the atoms, possibly a consideration in the stability of the ß-phases, are +3.1 in AgCd and + 4.2 in CuZn. Likewise the relative electronegativities of the two pairs of metals are about the same, CuZn possessing an electronegativity difference of 1.0 and AgCd one of 0.8. These values are from a table of electronegativities given by Darken and Gurry." The phase diagrams of the two systems around 50 atomic percent are similar, both possessing a disordered body-centered cubic phase, ß, at high temperatures and an ordered bcc phase, ß, at room temperature; however, the ß and ß' phases of AgCd are separated by a hexagonal phase, [, stable in the range 220-440oC, which has no analogue in CuZn. There has been confusion in the literature as to the structures of the ß' and [-phases. The phase diagram in the ASM handbook'" has the structures of the two phases interchanged; however, Hansen" reports the correct relative positions and Muldawer" verified that ß', the low-temperature phase, is body-centered cubic. Work by the present authors also

Jan 1, 1959

By Ralph K. Foster

During five underground mine fires which occurred in Arizona during 1980 and 1981, sealing the fire area became necessary. To minimize leakage into the fire area, ventilation control measures were instituted to balance pressure across the bulkheads. Problems en- countered in sealing the fire areas and measures taken to improve these conditions are discussed. The routing of the ventilation and ventilation control to en- sure the workers' safety were also important considerations in reopening the mines. The use of continuous CO monitors is discussed. One important consideration was the condition of the fire, and chromatographic analysis was used to establish this. Graphs comparing the Trickett ratio, carbon monoxide, carbon dioxide, and oxygen concentrations are given. The Trickett ratio was useful but needed to be augmented by the comparison of CO, C02, and 02. Problems with getting good samples from sealed areas and recommended procedures that were developed during these fires are discussed.

Jan 1, 1982

As reported in Drift last month demolition of old buildings on the 47th St. site has been completed, and detailed plans and studies for the new structure are well underway. As this issue was being sent to press the $5 million industry- business phase of the fund campaign had passed the half- way mark toward its goal. Target date for the building program is 1960.

Jan 5, 1958

By Alfonso Rizo-Patrón, A. M. Gaudin

PREVIOUS studies of activation in flotation have directed attention to the action of the activator on the mineral to be floated rather than to the relationship of the activator to the collector. The latter phase of the problem, however, seems to have definite scientific, if not also practical, interest. In the investigation reported in this paper, experiments were carried out, largely with quartz as subject, barium as activator, and oleate as collector. The results obtained indicate that a I : I ratio of collector ion to activator ion gives optimum results, and that a 2:I ratio almost fails to achieve activation and flotation. Yet, a 2:I ratio would have been expected on stoichiometric grounds, had the coating been a normal salt of the activator ion with the collector ion, since barium is a divalent cation and oleate a monovalent anion. To interpret and rationalize the observations, considerations of the crystal chemistry of quartz are helpful. The point of view to which these considerations lead may be of general applicability to systems involving suspensions of solids in liquids; they confirm that an adsorbed coating is inescapable. APPARATUS AND SUPPLIES The experimental work consisted in barium-ion abstraction tests, hydrogen-ion and hydroxyl-ion abstraction tests, flotation tests, and determinations of the surface of the crushed quartz. The flotation machine was built according to the design of D. W. McGlashan.* It consists of a drill press in which the bit has been replaced by a stainless-steel impellor surrounding a stainless-steel stator, as in the Fagergren laboratory machine. The air intake is controlled by a valve, and the cell consists of a beaker. The quartz was obtained from vein quartz stored in large chunks. It was first crushed to 20 mesh, then sized on a 28-mesh screen. The 20 to 28-mesh size alone was retained for use. This size was freed of coarse iron by passage through a Ball Norton magnetic separator, bleached with boiling hydrochloric acid to remove residual abraded iron, washed with distilled water until the washings were thoroughly free of ferrous, ferric, and excess hydrogen ion, and stored in covered Pyrex beakers under water until used. The barium was used as barium chloride, Baker's analyzed C. P. The oleate was used as sodium oleate. It was prepared from sodium hydroxide, Baker's analyzed C. P., and oleic acid purified by R. R. de Arellano3 in the laboratories at the Massachusetts Institute of Technology. The purification procedure was elaborated from the recent researches of Brown and Shinowara.2 It consisted in: (I) saponification of olive oil with potassium

Jan 1, 1942

By J. Richard Lucas

The coal industry, one of the great basic industries in the nation, plays a major role in the American economy. Coal is the principal fuel used in generating tremendous quantities of low-cost power so necessary to the nation. Two-thirds of the electrical energy and one-fourth of all energy consumed in the nation is produced from coal. Large-scale production of steel, cement, and chemicals is vitally dependent upon this natural resource. Because of extensive reserves and low mining cost, it is one of the few natural resources in which the United States is a significant exporter. During 1965 in excess of 500 million tons of coal were produced, almost 10% over the previous year; more than 50 million tons were shipped to foreign markets. The utility market gained approximately 8% during the year for a total of 242 million tons.

Jan 2, 1966

By Norman Pilling

The deleterious effect on the mechanical properties of copper, resulting from heating in contact with reducing gases, is well known, but the mechanism of the action does not appear to have been definitely established. The purpose of the present investigation was not to determine the exact variations in physical quality of commercial copper, with its various impurities, as dependent upon the composition of the gas, temperature of exposure, etc., but rather to study the nature of the action and the conditions under which it occurs. The physical result of the so-called "gassing." of copper has been generally described as the development of "brittleness." There appears to be a striking decrease in tensile strength, associated with a considerable loss of ductility, and a small copper strip or wire affected in this way can he snapped in two when bent. Larger articles may have an outer layer alone affected, which can be detached from the core by hammering or bending. Perhaps the earliest reference to this subject is that of Heyn1 in 1900, and among the later observers may be mentioned Archbutt,2 Bengough and Hill,3 Johnson,4 Mathewson and Thalheimer,5 and Ruder .6 Bengough and Hill, while working with arsenical copper, were the first to suggest the possibility of the formation of gases within the copper itself, while Ruder endeavored to explain the action by the reduction of the

Jan 10, 1918

By R. E. Hurst, D. E. Ramsey, J. M. Moore

The "frac" method of well stimulation has been applied successfully to all producing formations in the Permian Basin area. During the five years since its development, many changes and improvements have been made in treating materials. procedures, and equipie11t. A number of fluid carrying agents, having different physica1 and chemical properties, have been developed to meet variorus well requirements. The current trend is toward larger gallonage treatments, employing higher injection rates. The use of "down-the-casing" techniques has greatly reduced high surface working pressures, attributable to friction losses resulting from injection throrugh tubing. Petrographic studies of various Permian Basin formations, coordinated with laboratory and well log data, have been found a valuable guide in planning frac treat111o1t.s. A knowledge of the extent (and orientation of naturally occurring fractures and planes of weakness in the formation, aid in predicting the ultimate drainage pattern resulting from the frac treatment. INTRODUCTION The South Permian Basin covers an area in Wcst Texas and New Mexico about onc-half the size of the state of Texas, This vast region has been called the "Permian Basin" for so long that the term will he used here. It includes an area south of the Matador Arch. approximately 250 miles wide and 300 miles long. Structural features of importance within the basin are the Northwest Shelf, Eastern Platform, Midland Basin, Central Basin Platform, and Delaware Basin. The principal producing formations include sand, limestone and dolo-mite, with lesser amounts of shale, anhydrite. chert. and various silicates. All of the producing formations in the Permian Basin have responded to some type of frac treatment. Essentially, a frac treatment may be defined as the injection, into a formation. of a fluid carrying agent containing a particulated solid (usually sand), for the purpose of increasing production. The application of this method of well stimulation to many differing Permian Basin reservoirs has necessitated numerous changes and improvements in carrying agents, solids, service equipment. well equipment. and treating techniques. CARRYING AGENTS A number of different types of fluid carrying agents have been developed since the introduction of the frac method of well stimulation. These agents have different physical and chemical properties, and in many cases the extent of production increase derived from the frac treatment depends on the choice of fluid carrier. Unfortunately, due to many different systems of nomenclature used in the oil field, these differences are not always recognized by the oil Operator. In general, carving agents may he divided into the following broad classi-

Jan 1, 1956

By Joseph P. Hodgson

JOSEPH P. HODGSON.-As to ".Safety First," I did not deal with that, but I will say that in 1913, the number of .men killed was nine, and that year the "safety first" program was commenced; the next year, 1914, the number was reduced to five. In 1915, I am pleased to say that the number was reduced to two in the Copper Queen's entire property, and we have none so far this year. THE CHAIRMAN (G. F. G. HERMAN, Bisbee, Ariz.).-I can say, further, that we have from eight to nineteen men per month incapacitated for more than 14 days. Those are classified in this State as serious accidents. The number of men injured has apparently increased, -but that is clue to our improved method of recording and classifying accidents, no matter how slight. C. W. GOODALE, Butte, Mont.-The importance of cooperation among the members of the staff of an industrial organization is well brought out by Mr..Hodgson's paper.

Jan 12, 1916

By George L. Reiter, George B. Clark

Commercial strip mining of coal was first begun in the state of Illinois in 1911.l The annual tonnage of coal produced from coal strip mines in the state was very small until 1924, when the strip mines shipped 1.68 pct of the total state shipping mine tonnage. Since then, strip mines have gradually come into their own by producing a sizable percentage of the coal produced in the state. Table 1 shows the coal tonnage shipped from both underground and strip coal mines in the state of Illinois for selected years. The table illustrates the major role that strip mines play in the state's coal industry. Today, strip mining is generally conducted in areas where the coal seams lie so close to the surface of earth that a stripping method of mining the coal seam is cheaper than an underground method. Strip mining not only recovers 100 pct of the coal deposit, but may also be used as a method of mining large acreages of coal abandoned by the closing of underground mines. Open cut or strip mining is a very highly mechanized method of producing coal and is carried on in three distinct and separate operations. The first of these is uncovering or exposing the coal seam so that the coal is made available for mining. The second operation is that of actually mining the coal. The third operation is the washing, crushing and grading of the coal according to the producer's market. Description of Shovel The Marion 5560 power shovel is used in the first of these three operations. The large electric-powered shovel works forward and back across the coal deposits, removing the overburden of dirt, rock, and clay in successive cuts of 30 to 60 ft deep and 40 to 80 ft wide. The shovel has a maximum cutting height of 95 ft, but around 60 ft is considered to be the maximum economical cutting height by the operators. The smaller the depth of cut, the more economically the shovel will operate until a minimum cut of 15 ft is reached, below which the efficiency decreases rapidly. The Marion shovel may be used in tandem stripping in excessive depths of overburden. The other type of excavating equipment used in the tandem team is generally a dragline with a long boom of about 180 ft. In tandem stripping, the dragline is used to remove the upper portion of the cut and to place it at a maximum dumping radius from the place of removal. The Marion 5560 power shovel is then used to remove the overburden left above the coal seam and to deposit it at the shovel's maximum dumping radius. The Marion 5560 power shovel is of gigantic proportions. It has a 102 ft 6 in. boom and 32 cu yd dipper and is

Jan 1, 1950

By Enid C. Plante

This paper deals with the flotation of the mineral fluorite (calcium fluoride) and of two associated gangue minerals, calcite and quartz. The aim of the investigation was to produce "acid-grade" fluorite, which must contain less than one per cent of silica. Several reagents are used successfully in practice for floating fluorite from its ores. Oleic acid is the most widely used collector, usually at temperatures above 60°C, with sodium silicate as a dispersant for quartz and quebracho or tannin to depress calcite. Sulphides (e.g., galena) are often removed first by xanthate flotation. Many investigators23 report results in which more than 80 pct of the fluorite is recovered in a concentrate assaying 96 pct or more of fluorite and less than I pct of silica. This investigation was undertaken with the intention of floating the gangue, which is the minor constituent of the ore, from the fluorite. Hence emphasis was first placed on the cationic compounds that float quartz. No satisfactory separations were obtained in this way, and other reagents were investigated to discover whether these were more effective than oleic acid in floating fluorite from quartz in the usual way. The first part of the paper describes experiments with several long-chain collectors available commercially. Most of this work has been by captive-bubble and cylinder flotation tests, with some batch tests in a flotation machine. The second part describes the use of sodium cetyl sulphate as a collector for fluorite and includes laboratory tests and extension of the work to batch tests in the flotation machine. A method for determining the adsorption of sodium cetyl sulphate on fluorite has been developed and is described. Theory of Collection by Paraffin-chain Salts It may be assumed that these compounds are adsorbed at the mineral surface in one or more of three ways outlined by Kolthoff:12 1. Exchange adsorption between lattice ions in the mineral surface and collector ions in solution. Closely related is adsorption by the collecting mechanism postulated by Taggart,17 in which there is metathesis between the collector and the mineral cation or anion. 2. Exchange .adsorption between adsorbed gegen ions (p. 67, ref. 19) and collector ions in solution. 3. Adsorption of nonelectrolytes (polar-nonpolar) without displacement of adsorbed ions. With cationic collectors, inorganic cations in the solution (e.g., hydrogen ion) compete with the collector ions and therefore act as depressants, while inorganic anions have the same effect with anionic collectors. From this follows the general conclusion that ions of the same charge as

Jan 1, 1949

By R. V. Norris

IT was stated in a former paper1 that an intensive study of anthracite costs was being made by the engineers of the United States Fuel Administration. The results of this-study are now available and are offered as a supplement to the former paper. Anthracite costs as reported, for the 6-months period, December, 1917, to May, 1918, inclusive, as compiled by the Federal Trade Commission, were used as a base, and charts similar to those described in the-former paper were made for the standard white ash anthracite and for red ash and Lykens valley coals. ADJUSTMENTS The adjustments of cost from a reported to a price-fixing basis, as described for the bituminous methods, were applied but showed only minor adjustments as necessary. The great spread in anthracite prices on the varying sizes, which for the 6-mo. period under review ranged in average from $5.244 for nut to $2.074 for barley coal, makes the question of the percentage of sizes produced at the different collieries a vital one. The realization with the same prices for each size must be within very wide limits, when it is considered that the percentage of prepared coal reported from different collieries varied from over 80 per cent. to below 30 per. cent. for fresh-mined coal. Hence, as the spread in prices for the various sizes must be predicated on some percentage, it is essential to find some method of adjustment to allow for this variation. The logical method of adjustment is to calculate actual costs to costs as of the standard percentage of sizes, so that the margin between the adjusted costs and the average realization shall be the actual margin for each colliery between its actual costs and actual realization clue to its particular percentage of sizes. As a base for realization the actual percentage of sizes for fresh-mined coal for the 6-mo. period was adopted. This percentage is given in Table 1.

Jan 2, 1919

By E. E. Roecker, J. F. K. Brown

For three years The Hudson Coal Co. has used egg anthracite instead of coke in its foundry cupola. It has long passed the stage of being told it cannot be done—the metal would be cold, of poor quality, or the speed of operation would be low. From observation, from use and from test. we know that our metal is about average; the cast iron invokes no adverse comment from the machine shop and the speed suits our foundry requirements. We have there-iore resolved into practice anthracite combustion processes in an industrial furnace formerly using coke, under conditions suitable to our needs. When it comes to translating what we know into use in another cupola, however, where operating conditions may be different, or to explaining why, with seemingly the same conditions in our own cupola, we have attained sometimes a temperature of 2800° in the metal and at another time 2600°, or a speed of 5 tons per hour against 2 35 tons per hour, we cannot do it. We cannot do this because there seems to be an unbridged gap between laboratory ideas on combustion and practical ideas on com-bustiqn, which we have been unable to cross in terms understandable to us as practical consumers. This gap or bridge centers around the problem of how combustion actually takes place; and we believe it is controlled by two factors: (I) the character of the surface of the fuel and (2) the space provided and needed within which the oxygen of the air is allowed to or can act on that surface. It has long been contended on behalf of coke that porosity is an important factor in combustion, although, admittedly, there are two schools of opposing thought on this question, as revealed in technical literature. It has been understood generally that a light, porous coke is the best metallurgical fuel because there are more square inches of carbon exposed to the blast of air, therefore more useful carbon-dioxide reactions can take place in the given space between the entrance of the air and the point where useful work is done. It is now our general idea that the heavier and the harder the coal, the better the metallurgical fuel, provided the surface of that fuel is suitable for fast reaction with the oxygen. Time and Space A cupola is loaded in layers of fuel and iron. The horizontal line where the first charge of iron rests on the coal is the top of the bed coal. With us that is 22 in., usually, above the tuyeres where the air enters. This means 600 lb. of coal. Every subsequent coal layer is 100 to 125 lb. of coal, and that 100 to 125 lb. of coal melts 1000 lb. of iron at around 2700° in the ladle. This quantity of coal represents a 3-in. layer spread across the cupola. The question arises: If this 3 in. of coal will melt 1000 lb. of metal, why was it necessary to use 600 lb., or 22 in., of coal beneath and between the first charge of iron and the air entrance?

Jan 1, 1944

By Benjamin C. Craft

Operations on the Louisiana Gulf Coast during 1936 resulted in the discovery of five new fields and the proving of flank production or new sands on 12 of the older fields. This district gained the rank as the outstanding deep-drilling region of the world. At the close of the year. 10 wells had been drilled beyond 10.000 ft. One of the most important

Jan 1, 1937

By E. Gaujot

IN connection with the question of coal waste and economy in mining, we would call the attention of those interested to an apparatus invented by M. Dernencourt, Superintendent of the Anzin Division of the Anzin Coal Company, North of France. This apparatus is known in France and Belgium under the name of prop screw-jack (vis botte), and has been used with good results in the above-named countries for some years past. M. Ponson gives, in his " Trait6 de I'exploitation des Mines," a description of it (page 533), but as the description given is old, the work not widely known in this country, and as some valuable improvements have been made since, I thought it might be useful to give a description of it, having seen it in 'operation in 1867, while in Europe to attend the great Exposition, and on a scientific tour to the mining districts of France, Germany, Belgium, and Italy. The prop screw-jack is composed of the following pieces : I. The body or column B, Fig. 4 [Plate (I)], of oak or yellow pine, sawed square, the bark taken off, and any length, proportionate to the vein. The smallest are 10 inches diameter at the base, and 9 inches at the top, the height being from 12 to 15 inches less than the size of the vein. In the axis of this column, and at the top end, is a cylindrical opening or hole, C, 22 inches diameter, 10 inches deep, for the screw, S. II. Two wrought-iron rings, R R, to strengthen the two extremities of the column ; the rings must be put on hot. III. A cast,-iron washer, E, with hole in centre a little larger than the screw, to be put on the top of the column, and on which the nut is to rest; the top side of this washer must be faced on the lathe, also the bottom of the nut, to prevent friction. IV. The screw, S, having a total length of 12 inches and a diameter of 24 inches (for very high veins this diameter may be increased to 3 inches), and has on its top a wrought-iron plate, T,

By Grover R. Castle

INTRODUCTION Banks are being asked to assume more and more of the project risk in connection with project financings and, as a result, they are seeking to become more sophisticated in the way that they approach these kinds of financings. For example, a large number of banks that are active with the mining companies have established mining groups which typically will include mining engineers, economists, and bankers, in order to specialize their service to the mining industry. These banks have geared up these special service staffs so that they will be better equipped in their lending activities to analyze, measure and evaluate the project risk. The hope is that a team of these specialists will be able to predict the potential success or failure of these new "green fields" mining ventures that the banks are asked to finance. This paper shall focus on this subject and try to determine just how successful these specialists can hope to become as they analyze these various projects that are brought to them for financing. The approach that shall be taken in this paper shall be to examine how successful the mining companies themselves have been in the past with this same problem. These mining companies should be the most sophisticated in their approach to the analysis of the potential for success of a new mine because they have had the most experience in evaluating these projects. After all, who knows more about developing a mine than the companies that have developed similar mines in the past? For the purposes of this paper, the writer has selected a sample of 18 mines that have been developed over the years and measured the actual performance of each of these sample ventures against the original projections. All of these cases have involved the development of large projects where the sponsors or partners in the venture are substantial and sophisticated companies and where the feasibility studies have been prepared by engineering firms that are considered very professional in the industry or alternatively where the feasibility has been done by a comparable in-house staff. The sample cases have been chosen from a period which starts in 1965 and continues through 1981 with the cases distributed over that period as indicated below: [ ] Fourteen of the projects are open pit mines, three are underground mines and one mine starts on the surface and gradually goes underground. Seven of the mines are in the the far east with the remaining three in either South or Central America. The following four specific questions were examined for each project:

Jan 1, 1985

By Nathaniel Arbiter

THE separation of minerals by flotation can be regarded as a rate process, with the extraction of any one mineral determined by its flotation rate, and the grade of concentrate by the relative rates for all the minerals. So regarded, the significant variables for the process are those that control the rates. These variables are of two types, the first describing the ore and its physical and chemical treatment prior to flotation and the second characterizing the separation process in the cells. This paper will examine the variation in rates for a group of separations, will show that a simple rate law appears to govern, and will consider the relation of the control variables to the rates. The use of rate constants for evaluation of performance and efficiency will be discussed. Flotation involves the selective levitation of mineral and its transfer from cell to launder. The flotation rate is the rate of this transfer. It may be defined by the slope of a recovery-time curve for any cell in a bank, or at any time in batch operation. The objective in flotation rate study is an equation expressing the rate in terms of some measurable property of the pulp. This can be either the concentration of floatable mineral in weight per unit volume1,2 or a relative concentration, which will be a function of the recovery." A rate equation for an actual flotation pulp will contain at least two constants, both to be determined from the data. One of these, the initial concentration or proportion of floatable mineral, is not necessarily equal to the feed assay because of nonfloatable oversize or locked particles." The other, a rate constant, is a measure of proportionality between the rate and the pulp property on which the rate depends. The value of the rate constant will be determined by the values of all variables which control the process and will be changed by significant changes in any of them. It is, therefore, a direct measure of performance. Where recovery or grade change continuously with flotation time, the rate constant will be independent of time and will characterize the entire course of the separation. Development of Rate Equations Rate equations can be developed either by analysis of the mechanism of the process or by direct fitting of equations to recovery-time data. Sutherland's attempt by the first method' suggests that the effect of particle size variation on the rate complicates the derivation of a simple equation applicable to an ore pulp. A further problem with an ore is the concentrate grade requirement, which usually involves a variable rate of froth removal. Thus the final rate for any cell may depend on the froth character and froth height, as well as on the pulp composition. This does not imply that each cell cannot reach a steady state2 in which the rate will depend ultimately on pulp composition. The second method is the fitting of rate equations consistent with the necessary boundary conditions* to experimental recovery-time curves. On the assumption that under constant operating conditions the flotation rate is proportional to the actual or relative concentration of floatable mineral in the pulp, a generalized rate equation may be expressed as follows: Rate = Kcn [I] where K is the rate constant, c is some measure of the quantity of floatable mineral in the pulp at time t, and n is a positive number. In previous rate studies, the value of n has been taken as 1, either by direct assumption," or as a result of the hypothesis that bubble-particle collision is rate determining.' A first order equation results, which after integration in terms of cumulative recovery R, leads to Loge A/A-R = Kt [2] The quantity A is the maximum possible recovery with prolonged time under the conditions used. No conclusive proof for the validity of this equation in flotation has been advanced. The evidence cited in its support consists entirely in the demonstration that it appears to apply to a limited number of recovery-time curves."' It will be shown subsequently that this procedure is not sufficient to establish the order of a flotation rate equation. The possibility that the equation may be of higher order therefore requires examination. If, in particular, the exponent in eq 1 is assumed to be 2, then after integration there results R = A2Kt/1 + AKt [3] with K again a rate constant and A the maximum proportion of recoverable mineral. Eq 3 may be

Jan 1, 1952

By Gerhard Derge

The extension of metallurgical control of steelmaking processes has always made it desirable to have some quick method for determining the oxygen content of molten steel. To meet the practical demands of the steel industry, this method must also be simple enough so that the sampling can be done by the regular furnace crew. This requirement was kept in mind continually in the work to be described. An oxygen value is required for proper control, whether it be of a rimming steel or of a fully killed steel. However, two factors have discouraged the development of such direct methods: i. The reaction C + FeO Fe + CO is rapid enough to make the correct sampling Of the bath a difficult problem. The most generally accepted means of circumventing this difficulty have been the aluminum-killed bomb test of McCutcheon and Rautiol and the aluminum-killed spoon test of Herty.2 The theory of these tests is that all of the oxygen in the iron is converted to Al2O3, which can then be determined by chemical methods. Even when simplified so that the analysis is made by a measurement of turbidity, this method is too slow to be used in routine control. Furthermore, the results obtained have never been entirely satisfactory, and some of the reasons for this will be discussed later in this paper. z. The ordinary chemical methods of analysis for oxygen in steel are not reliable. The only analysis that seems to possess sufficient dependability to be of value is vacuum fusion,3 and the apparatus and technique developed for this have been too complex and slow for routine work. Indirect Methods Indirect methods of estimating the oxygen have been resorted to in mill practice. Generally these depend upon the chemical equilibria involved. The oxygen in the bath is related to other components in the slag or metal that can be analyzed the readily. These methods have many difficulties in common. Steelmaking processes involve a complicated set of interrelated reactions, all of which tend to approach equilibrium at varying rates. The degree to which any particular equilibrium is approached is not well established. Moreover, a proper use of theoretical equilibrium constants requires a more extensive knowledge of the activities of the con- than we now have. This is well illustrated by the irregularities observed when trying to determine the oxygen in the metal by its ratio to the iron oxide in the slag. Equiliblium relations may be used mole readily if they are evaluated by plant experience, but the extent of approach to equilibrium remains an undetermined variable and lack of an entirely satisfactory mean, of determining oxygen for the calibration is felt keenly, For example, the statistical analysis of the relation between carbon and oxygen4.6 illustrates that even iia a single plant wide variations exist under llormal conditions of operation. Never. theless, this is one of the best methods now

Jan 1, 1943

By W. Joseph Schlitt, Kenneth J. Richards, John D. Prater

Kennecott Minerals Company has developed a leach-hydrolysis route for treating flue dusts from copper smelters The flue dusts are acid leached in an oxygen atmosphere to solubilize copper and fix the arsenic, antimony, and bismuth as stable compounds Copper is recovered by cementation with Iron and the barren solution is recycled Molybdenum and other values may be recovered by modification of the basic flow sheet Results of bench scale and pilot plant tests are discussed in terms of the effect of operating parameters.

Jan 1, 1981

By F. B. Plummer

THE physical properties of oil-producing sands, such as grain size, porosity, and permeability, are becoming more and more important in petroleum production engineering as oil fields are being repressured and rejuvenated. A number of excellent papers have been published recently on all three of these properties. Faucher, Lewis and Barnes1 give a com-plete survey of the work done through 1932 and contribute also much information on sands that they themselves have examined. Muskat and Botset,2 Wykoff, Botset, Muskat and Reed,3 Hurst,4 and Muskat5 have contributed a great deal to the theory and actual measurement of flow of liquids and gases through porous media. Muskat and Botset have measured the permeabilities of different sands with gases and liquids. They find that the radial is always slightly under the linear permeability. However, in most of the previous experiments small samples of the sand were used, and the method of production of fluid or gas through the sands has not been very close to actual oil-field conditions. In addition, so far as the authors are aware, no measurements of linear and radial permeabilities have been made simultaneously under exactly the same conditions. The multiple permeability apparatus described here is a part of the equipment being acquired by this laboratory for thorough investigation of the physical properties of producing sands. It possesses certain advantages for comparative studies of liquid flow. Additional data and descriptions of other instruments will follow in papers to be written later on. The essential features of the permeability apparatus are as follows:

Jan 1, 1934

By Kung-Ping Wang

This is the second installment of two-part article on the Far East. The mineral situation in Hong Kong, Indo-China, Thailand, Burma, Malaya, Indonesia, the Philippines, and British Borneo is covered.

Jan 12, 1951