Search Documents

By Klaus-Peter M. Hanke

INTRODUCTION In early 1979 Jim Walter Resources, Inc. (JWR) of Brookwood, Alabama approached TMCI Construction, Inc (TMCI) to make a proposal on a program that involved the sinking of up to 10 ventilation shafts of approximately 6.7 m (22 ft) diameter and ranging in depth from 500 to 700 m (1650 to 2300 ft) for the JWR coal mines in Alabama. At this time TMCI was already constructing the first spiral underground bunker (capacity 2000 tons) in North America for the JWR organization at their No. 4 mine in Alabama. The TMCI proposal was based on the use of the mos modern large diameter shaft boring machine rather than sinking the shafts using the conventional drill blast-muck technique. The proposal was made based o: the experiences by the parent company, Thyssen Schachtbau, which has been using this type of machin in Germany for shaft boring since 1971. As a result of the TMCI proposal JWR issued a purchase order to TMCI for the construction of four 6.7 m (22 ft) diameter, concrete lined, unfurnished ventilation shafts ranging in depth from 500 to 700 (1650 to 2300 ft). An order was thus placed with WIRTH Machinen- and Bohrgeraete Fabrik GmbH, in Germany for the manufacture of a model 650/850 E/Sch "Schachtbohrmaschine" (Vertical Shaft Borer = V-mole which arrived on site in Alabama in early 1981. The first V-mole GSB 450/500 was introduced in Germany in 1971 and was capable of enlarging in one step a pre-drilled 1.2 m (4 ft) pilot hole to 4.5 - 5.0 m (14.7 - 16.4 ft). This machine has sunk 9 staple shafts and deepened one surface shaft for a total of 2360 m (7740 ft) of shafts. On the last shaft boring operation in 1978 the machine was converted as an experiment to drill without a pilot hol using a hydraulic pumping system to remove the cutting debris. A second generation machine, the SB VI 500/650, was introduced in 1977 for enlarging the pilot hole to a range of 5.0 - 6.5 m (16.4 - 21.3 ft) diameter. This machine is still in operation and has already drilled well over 2000 m (6500 ft) of shaft. The third generation of V-mole, the SB VII 650/85( for diameters from 6.5 to 8.5 m (21.3 to 27.9 ft) was: commissioned in May 1980 and has been used for two surface shaft deepenings totalling 606 m (1990 ft) with another scheduled for 1982. The main advantages favouring the use of such V-moles were identified as: 1) A reduction in manpower to the crew required in a conventional shaft sinking operation. 2) A considerable reduction in time to complete a shaft compared to conventional techniques. 3) The use of the V-mole eliminates many of the hazards encountered in conventional sinking. Based on the successful performance of the first three V-moles in Germany, Thyssen Schachtbau decided to employ this principle abroad. In 1980 a second machine of the third generation was built and is now operated by TMCI Construction, Inc. in Alabama. The first shaft was completed at the end of 1981 and this paper describes the method of operation including some unique aspects not attempted on prior V-mole operations and some of the statistics arising out of the experiences during the first shaft boring operation. THE NO. 7 MINE FAN SHAFT SITE Jim Walter Resources, Inc. was formed in 1970 to exploit the coal field in Alabama on the southern tip of the Appalachian coal field. The coal reserves amount to around 650 million tons of mainly good quality coking coal of which about 350 million tons are to be extracted over the next 30 years. Shaft sinking and preparatory work began in 1972, and at present 6 mines are producing around 5.4 million t.p.a. Annual production is to expand to 10 million t.p.a. as soon as possible, and the ventilation shafts to be sunk by TMCI play a vital role towards attaining this goal. The first shaft site is located at the No.7 mine, near Brookwood, Alabama. The actual location of the shaft relative to the production shafts is shown on the mine plan (Fig. 1), which also shows the room-and-pillar extraction system used at present. The mine plan further shows the conveyor route used for the muck removal. The geological survey showed that the strata consisted of horizontal layers of mainly sandstone, sandy shale and shale interspersed with several coal seams. The seam being extracted at the No. 7 mine is a combined seam made up of the Blue Creek and Mary Lee seams at a depth of 513 m (1682 ft) and having an average seam thickness of about 2 m (6 ft). At the beginning of September 1980 the surface site preparation and pre-grouting work was completed by JWR, and TMCI was able to commence with Stage I of the shaft sinking program - the drilling of the pilot hole.

Jan 1, 1982

By Lo-Ching Chang, Kenneth M. Goldman

INTRODUCTION THE kinetics and mechanism of transfer of a constituent across a slag-metal interface are fundamentally important because many metallurgical processes involve the existence of a slag phase and a metal phase. Industrial processes seldom proceed to equilibrium, and information of the rates and modes of reactions are therefore often of greater practical importance than equilibrium data. A study of the kinetics of sulphur transfer across a slag-metal interface under reducing conditions will contribute a great deal toward a better understanding of desulphurization in the blast furnace process. The general principles existing in the transfer of a constituent, such as sulphur, across a slag-metal interface can be extended to similar transfer phenomena in other metallurgical processes. The present paper will demonstrate how such studies will lead to fruitful results from both the practical and theoretical standpoints. EXPERIMENTAL METHOD The apparatus used was simple. A graphite crucible 1 5/8-in. id, a wall 1/8-in. thick, and a depth of 4 in., was packed in an outer fused silica tube with powdered magnesia. The crucible assembly was rotated at a speed of 235 rpm inside an induction coil. A charge of 250 g of Armco ingot iron was introduced into the graphite crucible and melted by induction heating. The melt was held at a desired temperature [ ] for 3-5 min., after which 7.5 g of granular ferrous sulphide was added and the bath was held for another 3-5 min. A metal sample was then taken by means of a fused silica tube and a rubber suction bulb. Immediately after the metal sample was taken, 30 g of a prefused and crushed slag were introduced. The slag reached the temperature of the furnace in 1 to 1 1/ 2 min. Slag

Jan 1, 1948

By S. Webster, M. Karmis, C. Haycocks

Mining any seam can seriously affect subsequent operations in coal seams both above and below the one being mined. The effect is often detrimental to the recovery, cost and safety of mining the subsequent seams. This paper describes the ground control mechanisms involved in mining through a passive subsided zone or all actively subsiding trough. Data were extracted from case studies, primarily from the Appalachia region, for construction of empirical models to predict interaction problems that can occur in overlying seams. Inner-burden thickness, innerburden lithology, percentage extraction, lower seam height, time and overburden were analyzed to determine their effect on upper seam damage. Magnitude of upper seam subsidence was incorporated, together with a broad classification of rock types, to predict the type and range of damage that can occur in the upper seam. Results are summarized in graphically and nomogram form for use in. engineering design.

Jan 1, 1984

By H. D. Hoskold

It was not for the purpose of asserting any superior knowledge or authority, but simply of clearing up, in greater detail, some points casually mentioned in Mr. Scott's able paper, that the writer entered, some two years ago, into the discussion which that paper initiated. In such matters there is always room for differences of judgment, as well as for additional data, which may modify or complete the conclusions even of the best authorities. Those who are immersed in the duties of practical administration or work in the field, and who, being remote from the great scientific national libraries, are obliged to rely on their private collections, and to supplement them by their recollections of earlier studies, labor under special disadvantages in such a discussion; and it must be to the scientific and engineering world a matter for gratitude that Mr. Lyman has been willing to give the benefit of his advantages in this respect. Mr. Lyman would, however, doubtless at once disclaim the conclusion that his masterly summary constitutes " the last word " on this subject, and welcome further evidence, comment and criticism, such as the various contributors may continue to offer. This, therefore, is the motive, and must be the excuse, of the introduction by the writer of the following observations. The Miners' Dial.—Many years since, the writer employed a miners' dial, older in type than Fig. 12,* but without any attached spirit-level, made by Thomas Jones, a pupil of the great Ramsden. Jones was one of the old London makers and opticians, and enjoyed great reputation for accuracy in the con-

Jan 1, 1902

By J. E. Neal, C. T. Naber, O&apos

Silicon thin films were deposited by electron beam evaporation in an ultrahigh vacuum onto (0001) and (1102) sapphire substrates. Attempts were made to correlate the structural properties of the deposited silicon films with the following: 1) substrate orientation, 2) substrate surface condition, 3) substrate temperature, and 4) deposition rate. The substrate temperatures were varied between 500° and 1000°C and the deposition rates were varied between approximately 50 and 700A per min. The following sapphire surface treatments were investigated: 1) annealing in the ultrahigh vacuum at 1200° C; 2) heating in a hydrogen atmosphere at about 1350°C; and 3) etching with silicon by evaporating silicon onto sapphire substrates heated to 1200° or 1300°C. Twinned silicon films were occasionally formed at substrate temperatures between the 800° and 1000°C on unprocessed mechanically polished substrates; however, the reproducibility and crystallinity of these films were generally poor. Single-crystal and twinned silicon films were formed at substrate temperatures between 700° and 1000°C on substrates which were silicon-etched at 1300°C prior to deposition. Fiber texture films were formed at substrate temperatures between 500° and 700°C. The (111) lattice plane of the silicon single-crystal films was parallel to the (0001) sapphire plane and the (100) silicon plane was parallel to the (1102) sapphire plane. TECHNIQUES are well-established for growing single-crystal silicon thin films on sapphire by chemical methods.'-* Vacuum epitaxial techniques have a number of advantages over chemical epitaxial techniques in the fabrication of thin film microcircuits.5 One of the most significant is that vacuum techniques are compatible with well-established procedures for forming vacuum-deposited thin-film resistors, capacitors, and interconnections. Salatna, Tucker, and young6 recently reported the formation of relatively poor crystalline-quality silicon films on sapphire by electron beam evaporation in a vacuum of about 7 x 10-7 Torr. The purpose of the investigation described here is to determine the relationships between the structural properties of silicon thin films deposited on sapphire substrates by electron beam evaporation in an ultra-high vacuum and the following: 1) substrate orientation; 2) substrate surface condition; 3) substrate temperature; and 4) deposition rate. The substrate temperatures were varied between 500° and 1000° C and the deposition rates were varied between approximately 50 and 700A per min. Two orientations of sapphire were used: (0001) and (1102). The thick-nesses of the films were between 8000 and 16,000A. The morphology and crystallinity of the deposited films and substrate surfaces were investigated by optical microscopy, electron microscopy, and electron diffraction. APPARATUS AND PROCEDURE A cross section of the ultrahigh-vacuum thin-film evaporator is shown in Fig. 1. The bell jar is stainless steel and copper gaskets are utilized at all seals. High vacuum is attained by a 6001iter per sec ion pump and a titanium sublimation pump. Sorption pumps are used to rough the system to a pressure of about 10 µ prior to starting the ion pump. Vacuums in the 10- 10 Torr range were attained after baking the system at about 250°C for 8 hr. Vacuums in the 10-8 to 10-9 Torr range were maintained during silicon evaporation. The silicon charges, which were cut from p-type single-crystal boules which had resistivities between 2000 and 4500 ohm-cm, were placed in the water-cooled copper crucible of a 180 deg bent-beam 5-kw electron beam evaporator. During evaporation, a molten zone was formed in the top center of the silicon charge, and the portion of the silicon charge in contact with the water-cooled crucible remained solid. The substrate heater, which has been described

Jan 1, 1969

By John R. Spencer

A capillary tube variable volume cell is described, which has operated satisfactorily over a range of 100°F and 3,500 psi to 550°F and 1,500 psi. The cell contents are entirely visible over the length of the capillary with the exception of a space at the top amounting to three per cent of the total volume. Observations on the critical behavior of simple systems have been greatly facilitated by the apparatus, it being possible to establish the critical conditions for a particular mixture in the course of a day's run. INTRODUCTION Many types of apparatus have been designed for obtaining data on the phase relationships of hydrocarbon systems. Such apparatus can in general be subdivided into two classifications; (l), indirect measurement of phase volume, and (2), direct visual observation of phase volume, each of which has outstanding advantages and disadvantages. Indirect measurement of phase volume requires the use of rather elaborate apparatus including internal probes in which are located the device for determining the locus of the interface between phases. Such equipment is by its very nature costly, and is complex from the standpoint of operating technique. Probing techniques can be used, however, over wide ranges of temperature and pressure with a high degree of reproducibility. Apparatus for visual observation of phase behavior obviously has the advantage of enabling the experimenter to see exactly what takes place, but because the material to be tested is contained in a cell constructed of both metal and glass, is limited severely as to the temperature range of operation. Furthermore. the maximum pressure usually is limited by the choice of material used for sealing the glass to the metal, and by the strength of the glass itself. In the interest of increased efficiency of observation, as much of the cell as possible should be visible to the eye. Glass capillary tubes have been used successfully but have always given difficulty at the metal-to-glass seal. An apparatus has been devised to overcome the problems of sealing and resistance to temperature effects that have heretofore been the limiting factor with glass apparatus in the observation of phase volumes at elevated temperature and pressure. APPARATUS The objective which dictated the general arrangement of the apparatus (Figs. 1 and 2) was simplicity of operation. The air bath, A, was constructed of an iron framework to which was attached approximately one inch of glass wool bats which were covered on the outside with "Masonite." A roughly octagonal center piece was installed to provide forced circulation of the air by the fan, B, past the heaters, D, cell, F, and thermoregulator, C, respectively. The entire top of the box is removable to facilitate charging of the cell and to permit easy maintenance. Two windows are provided before and behind the cell to allow the operator to observe the contents against the background fluorescent light, E. The heaters,

Jan 1, 1951

By George A. Roberts, Arthur H. Grobe

H. H. Hausner (Sylvania Electric Products Inc., Bayside, N. Y.)—I tested the 18-8 stainless steel powder described by Grobe and Roberts and the results were excellent. The powder was compacted and sintered in purified hydrogen to a very low density (approximately 20 pct and more porosity). Where the other powders show very little ductility when sintered to such a low density, the described stainless steel was surprisingly high in ductility. I would appreciate it if the authors could give us some data on a similar powder but without silicon and also data on 430 stainless steel powder. H. S. Kalish (Sylvania Electric Products lnc., Bay-side, N. Y.)—I should like to verify the excellent results obtained by Grobe and Roberts with their pre-alloyed stainless steel powder. It seems to me, however, that their data are conservative and that even better densities and higher tensile strength can be obtained with these powders by the selection of proper particle size fractions. The accompanying data were obtained by sintering compacts pressed from the powder made by Vanadium-Alloys Steel Co. to 0.8 in. in diam about % in. high in a cylindrical double action die without the use of lubricant. The compacts were sintered for 1 hr at 2370°F in hydrogen purified by passing it through a Deoxo unit (palladium catalyst) and a Lectrodryer. Even the density obtained using the as-received (—100 mesh) compacted at 40 tsi was quite high as was the hardness. This indicates that by increasing the sintering temperature slightly above 2350°F the coining and subsequent secondary sintering operation can be avoided. With the — 325 mesh fraction, however, very much higher density can be obtained and a high hardness. I have no tensile data to present, but I feel that it is not too optimistic to expect. that unusually high tensile strengths and good ductility can be obtained in this sintered material on the basis of the density and hardness data. The sintered stainless steel made by the above-described methods came out of the furnace very bright and clean. The purified hydrogen atmosphere is important in sintering stainless steel to reduce the oxide present in the powder. The result of such a sintering is good densification and good ductility of the sintered product. G. A. Roberts (authors' reply)—We are greatly indebted to Messrs. Hausner and Kalish for their discussions of our paper. Their encouraging remarks are greatly appreciated and their confirmatory data will do much to add to the value of the paper. At the present time it is impossible to provide complete data on a similar stainless steel powder without silicon, but we do know that, in general, the properties are slightly inferior. Data on such a powder and on other stainless steel types are to be published in the near future.

Jan 1, 1952

By Mitchell, Edmund I.

VARIOUS suggestions as to proper fees for engineering services have been put forth by individual practitioners and by the American Institute of Consulting Engineers, the Connecticut Society of Civil Engineers, the Iowa Engineering Society and the Mahoning Valley (Ohio) Engineers, for the guidance of both the engineer and his client. The American Institute of Architects also has a schedule of minimum charges (revised 1908). So far as can be determined, however, the four national societies representing civil, mining, mechanical and electrical engineering have never given consideration to this question. An examination of technical periodicals published during the past decade shows that these schedules make provision for three methods of charging; i.e., (A) a percentage of the cost of the completed project; (B) a per diem rate; and (C) a fixed sum. Suggested minimum charges are as follows:

Jan 1, 1921

By E. W. Davis

The: mysterious Lake Erie price for iron ore, established each spring, determines the maximum price that will be paid during the following season for ore of Mesabi Non-Bessemer base grade. This price is important to the ore producers, hut since most of the ore in the Lake Superior district is owned or controlled by consuming interests, the really important question to them is not the price of ore but how much it will cost them to mine and transport their season's requirements to their furnace plants. However, a few million tons are actually sold each year, and considerable quantities are traded for mixing purposes, and the negotiations lor these sales and trades usually begin with some reference to the Lake Erie price. There is no difficulty with the Lake Erie price itself or with the manner in which it is established, but the system prescribed for determining the values of ores that are not exactly base grade is incomplete. The Lake Erie price takes into consideration only the iron and phosphorus contained in the ore, but when the ore producer is negotiating a sale or trade, he is confronted by the fact that his ore must he studied and the price adjusted, not only on the basis of the iron and phosphorus analyses, as specified by the Lake Erie price, but also on the basis of silica! alumina, manganese, structure, etc. The vague and unsatisfactory methods used in making these adjustments bear some relation to the manner in which the ore is supposed to act in the blast furnace. The ore producer may not understand all of the idiosyncrasies of the blast furnace, but if the smelting-plant operators have a system more accurate than the Lake Erie price method for determining the relative values of different ores, why not pass this information on to the ore producers, so that they can make use of it and perhaps modify their practice in such a manner as to benefit both themselves and their customers? There is a lack of understanding and appreciation between these two groups that may, to some extent, be unavoidable, but in the interests of efficiency and conservation rules that are more accurate and complete than the Lake Erie price method in use at the present time should be established for the guidance of the ore producers. Recently a paper was read before the Eastern States Blast Furnace and Coke Oven Association, by Mr. G. W. Hewitt, Manager Production, Blast Furnace and Coke Oven Department, Wheeling Steel Corporation, in which he explained how his company determines the relative values of different grades of Non-Bessemer ore. This is a very important paper, perhaps not so much on account of the actual calculation methods described as because of the fact that premiums and penalties are shown on Non-Bessemer ores for silica, alumina, phosphorus, and manganese. As pointed out by Mr. Hewitt, the premium and penalty system described may not apply without adjustments to other smelting plants. However, if the various ore

Jan 1, 1941

By A. Alonso, J. Daubenspeck

In the nickel extraction process at Nicaro, Cuba, dried and ground nickel bearing laterites are reduced at 1300-1400F in multiple-hearth furnaces. Nickel is leached from the reduced ore by aeration in an aqueous solution of ammonium carbonate. Nickel carbonate is precipitated from the liquor and calcined to yield nickel oxide. The following are the more important modifications of the Nicaro process since plant rehabilitation and expansion. Ten percent increase in tonnage was achieved without decreasing the fineness of the ore by minor mechanical modifications of the grinding plant. Another five percent increase in tonnage was attained by intentionally overloading the ore prepration and leaching circuits in an effort to control cobalt extraction. Modifications at the sintering plant allowed it to handle the entire output of the expanded plant. A fifty percent increase in leach liquor cooling facilities alone provided an increase in nickel production of five percent. Stronger fresh leach liquor for increased nickel washing efficiency was obtained through improved distribution of water to the ammonia absorption towers. Advantage was taken of the reduced calcine's capability to precipitate cobalt, and modifications in the leach liquor circulation provided controlled cobalt solubility with minimum harm to nickel extraction. Several process changes at the drying plant brought about a ten percent reduction in the fuel oil consumption at this pint. Controlled air addition to the reduction furnaces' upper hearths burned formerly wasted combustibles thereby reducing oil consumption by twenty percent. The nickel extraction process successfully emplayed on the extensive but lowgrade lateritic ores of Eastern Cuba at the U. S. Government owned Nicaro plant, has been previously described in various publications. The large mine and plant operated by the Nickel Processing Corporation, located on the northeastern shore of Oriente Province, have been recently expanded to a yearly capacity of about 50 million pounds of nickel. Essentially, the operation involves open pit mining of a limonite-serpentine ore mixture containing 1.3 to 1.4 percent nickel and 34 to 38 percent iron. The comparatively lumpy, wet (25 to 30 percent moisture) ore is first dried and ground prior to chemical treatment, to which the entire 7,000 tons per day feed must be subjected. In the initial chemical action the dried and ground ore is reduced with carbon manoxide and hydrogen at 1300-1400° in multiple-hearth furnaces. The resulting metallic nickel is selectively leached from the reduced calcine by aeration in an

Jan 1, 1961

By G. R. Fritterer

INVESTIGATORS in the field of temperature measurement have long sought a thermoelectric couple fulfilling the following requirements: 1. It should be useful up to and including high industrial tempera-tures; i. e., 1000° to 1800° C. 2. Its thermoelectric variation with temperature should be linear and be maintained after heating to high temperatures for long periods of time. 3. It should be reproducible; i. e., different couples of the same elements should have similar calibration curves. 4. Its thermoelectric power should be large so as to allow the industrial use of rugged recording instruments. 5. Chemical reactions with, and physical changes within the elements of the couple should not alter its calibration. No thermocouple proposed to date exhibits simultaneously all of these characteristics, whereas the couple about to be described fulfills all requirements to a satisfactory degree.

Jan 1, 1933

By John C. Holtz

Hostility is a characteristic of the environment in underground mines. Nature opposes man's efforts to remove mineral deposits, and this condition is recognized when mining is described as winning minerals from the earth. Evidence of this conflict is the action of natural forces to close excavated passageways. In many mines, this behavior of the surrounding environment is an ever-present and ever-changing problem despite much research and empirical study. Geological conditions change abruptly and may result in rock bursts, the inrush of water, or variations in rock hardness. Although aspects of these problems will become intensified as the rate of mining increases, they are not considered in this discussion. Emphasis herein will be on the changes in the atmospheric environment. Men underground work in an ever-changing, alien, ambient atmosphere. Many conditions are encountered that will affect their health and safety unless properly controlled. Potentially explosive gases are released from minerals as they are mined or enter from the surrounding earth. Some mining methods generate noxious gases. Natural processes and diesel equipment can steal life-sustaining oxygen. Airborne dust may cause lung diseases when breathed by miners in excessive amounts and by affecting visibility, introduce safety hazards. Deep mines pose heat problems that may be aggravated by high-speed mining. The deleterious effects caused by these changes, and their mitigation, are subjects of this discussion. THE UNDERGROUND ATMOSPHERE Health and safety problems from changes in the underground atmosphere have been apparent since the beginning of mining. Alleviation of these problems has been by ventilation with normal air from the earth's surface that flushes away the vitiated mine atmosphere. The objective is to provide atmospheric conditions essentially similar to those that man is accustomed to on the surface.

Jan 1, 1970

By Eric Jette

IN a recent article,1 the authors reported the results of an X-ray investigation on the range of solid solutions that occurs in the iron-oxygen system in the vicinity of the compound FeO, which frequently is called "Wüstite." The object of that investigation was primarily to study the unusual type of solid solution phenomena involved in this range. Briefly summarized the results were: 1. The NaCl type of lattice found by earlier workers was confirmed. 2. The lattice dimensions decrease rapidly with decrease in iron content. 3. No alloy that was a homogeneous single phase was ever found at compositions beyond 76.80 per cent Fe, while the theoretical iron content of FeO is 77.73 per cent Fe. 4. Measurements of the densities and lattice constants led to the conclusion that the form of substitution was complex, an FeO group being replaced by oxygen. Such a substitution, of course, is equivalent to removing an iron atom (or ion). The ideal unit cell of FeO can be con-sidered as containing four groups of FeO and, thus, when this type of substitution takes place, there remain in the unit cell three FeO groups and an oxygen, or a total of seven atoms with a gross formula of Fe304 instead of the original Fe404. 5. This was the only interpretation that would fit the experimental results and at the same time be consistent with (a) the previously deter-mined fact that the FeO lattice is ionic (i. e., consists of Fe++ and 0= ions) and (b) the chemical fact that as the oxygen content of the substance increases, ferrous iron becomes oxidized to ferric iron. The experimental results of this investigation are included in Fig. 1.

Jan 1, 1933

By R. Frenkel, O. D. Sherby, J. E. Dorn, J. Nadeau

A method is shown for the study of the creep rate dependence of metals on the applied stress under the condition of constant structure. The method was applied to pure aluminum and to dilute solid solution alloys of magnesium, copper, germanium, zinc, and silver in aluminum. A linear relationship was found to exist between the true stress and the logarithm of the creep rate. ALTHOUGH extensive creep data are now avail-Aable, the fundamentals of the creep phenomena are as yet only vaguely understood. Many attempts have been made to formulate theories for creep. Eut their agreement with fact has been disappointing. It appears that merely pyramiding more of the same type of data that is now available will not provide the essential aid toward formulating a better understanding of the complicated process of creep. Perhaps attempts to construct better models for the mechanism of creep might have to be tentatively abandoned until new types of definitive creep data are uncovered. The question therefore arises regarding what type of data might be needed to provide the essential knowledge for formulating better and more realistic theories of creep. Perhaps one source of the failure to uncover an adequate theory arises from the fact that practically all theories for creep and nearly all analyses of experimental data on creep disregard the well-known fact that the structure of metals changes during creep. For example, it is customary in evaluating the effect of stress on the creep rate to correlate the secondary creep rate with the applied stress. But, as has been demonstrated recently,' the structures obtained during secondary creep tend to exhibit deformation banding at high stresses and polygoniza- tion at the lower stresses. Consequently the stress-secondary creep rate relationships found in this way are not fundamental, inasmuch as they reveal not only the effect of stress but also the effect of differences in structure on the secondary creep rates. It is the purpose of the study reported here to isolate the effect of stress alone on the creep rate in an attempt to provide new data for possible formulation of a better theory of creep. In addition an attempt will also be made to ascertain how structure, temperature, and alloying might affect the stress-creep rate relationship. The procedure that was adopted was simple: A specimen was precrept at a given engineering stress U, (initial engineering stress during creep under constant load, namely the load divided by the initial area of the specimen) and temperature T to a selected engineering strain, e (engineering strain, namely, the instantaneous gage length minus the initial gage length divided by the initial gage length), at which time the true stress was reduced to some lower value of the true stress, ^ (the true instantaneous stress, namely, the load divided by the instantaneous area). The instantaneous true creep rate, i, (the true strain rate; with E, the true strain, namely, the natural logarithm of the instantaneous over the initial gage length) following reduction of the true stress to U, was then determined. Second, third, etc., tests were conducted under identical conditions except the stress was reduced to yet lower values, us, u,, yielding yet lower instantaneous creep rates, ;, and i,. Inasmuch as the precreep conditions were identical in each series of tests, the instantaneous structures obtained immediately after reducing the stress were presumed to be identical.

Jan 1, 1955

By William N. Matheson

The major consideration in any management and engineering decision is the economic evaluation of factors. The right decision is the best cost decision, provided of course that it is the safest. Changes, improvements, and advances in mining technology, as in any business, come about through the pressure of economics in combination with the inventiveness and engineering abilities of efficient mine operators. Without proper economic evaluation and an appreciation of profit and loss of an operation, advances in mining methods would come about at a slow pace, if at all.

Jan 4, 1959

By Samuel Hoyt

THIS paper gives a brief description of an investigation made several years ago on the diffusion of zinc into copper. The material for that study was furnished in the form of thin copper strips coated with zinc. The result was required rather quickly and at not too great an expense, and especially information was desired as to the rate at which zinc would diffuse from the zinc coating into the copper and the temperature at which the operation should be carried out. A study of the requirements of this problem indicated that the solution might be secured by means of six determinations. This is the smallest number that will give the information desired and, at the same time, furnish checks on the accuracy of the determinations which justify an abbreviated experimental program. This does not count a preliminary test which was designed to give some idea of the correct temperature to use. The minimum number of temperatures that can be used is two. Knowing the rates of diffusion of zinc into copper at two properly chosen temperatures, it is possible to calculate the rate for any other temperature, and also to check the accuracy of the determination by means of the heat of diffusion, which is calculated from the effect of temperature on the rate of diffusion. The minimum number of determinations at any one temperature is three. The amount of diffusion which occurs at a fixed temperature is definitely related to the time of diffusion, so that by determining the amount of diffusion for three different time intervals, this relationship may be established and possibly a check on the accuracy may be secured. This accounts for the six determinations or experiments, and suggests the logical plan of the work. The check used here is not generally applicable to diffusion phenomena, but it seems to hold closely enough for the limited amount of diffusion in this investigation to justify its use.

Jan 1, 1928

By G. H. Shefelbine

DISCOVERED during the time of the Spaniards, the Namiquipa silver-lead-zinc mines in Chihuahua, Mexico, remained idle until 1916, when mining claims were first denounced. About 1922 a Japanese company, the Santo Domingo Mining Co., was formed to mine the oxide silver ore. The company built a 75-tpd cyanide plant and mined in the area for a number of years. Because of an error in surveying in one of the company's mines situated in another district, mining was carried over into a claim owned by General Marcel Caraveo, at that time governor of Chihuahua. Santo Domingo Mining Co. lost the resulting lawsuit and consequently had no capital to continue operating at Namiquipa. Later, Ray Brown and Eugenio Caballero formed a company to operate the mine, shipping crude ore to the American Smelting and Refining Co. smelter at Avalos, Chihuahua. The cyanide plant was changed to flotation with a capacity of 75 tons per 24 hr. In 1936 the property was again closed owing to labor trouble, a drop in the price of silver, and increased water in the mine.

Jan 10, 1957

By E. P. Chartkoff, W. P. Sykes

In 1926 one of the authors published researches on the determination and description of the iron-tungsten and iron-molybdenum systems,' including the equilibrium diagrams. In 1929, further work was carried on, including the examination by X-rays, which is recorded here. Meas-urements were made of changes in lattice parameters in the solid solutions. Precipitation from the solid solution and the accompanying changes in hardness were studied as well as the formation of the intermetallic com-pound phases upon sintering a mixture of metal powders. Materials All the specimens were prepared from the same quality of metals and by the same methods as were described in the determination of the constitutional diagrams. The metal powders as mixed and pressed were sintered or fused in a hydrogen atmosphere and subsequently treated as indicated in the titles of the figures. The formation of the iron-rich solutlon in the solid was accomplished by sintering in hydrogen for a period of 20 to 30 hr. at a temperature 25' to 50' C. below the melting point of the eutectic. The tungsten-rich and molybdenum-rich solid solutions of iron were prepared by adding the iron as a solution of iron ammonium oxalate to the oxide of tungsten or molybdenum, followed by a hydrogen reduction. This method results in a homogeneous alloy after sintering the pressed metal powder for 20 to 30 hr. at a temperature slightly below that of the peritectic reaction in the system involved. For X-ray examination the specimens were variously prepared, depending on the nature of the sample and what it was desired to show. For example, the iron containing tungsten or molybdenum in solid solution was cut with a file, the chips were put through bolting cloth, and this powder of filings formed the specimens for comparative study. The

Jan 1, 1930

By C. P. Lawhon, J. P. Simpson, W. M. Evans

Data obtained under controlled test conditions using a microbit drilling machine showed that oil emulsified in water muds may either increase or decrease the drilling rate, depending upon drilling conditions. A low-viscosity oil such as diesel fuel can give drilling rates in limestone almost equal to that of water. Data obtained for water emulsified in oil muds showed little decrease in the drilling rate in water-saturated cores as the water percentage of the mud was increased above the 5- to 10-percent range. Changes in drilling rate were found to be dependent upon the oil or water concentration of the mud and upon the type of formation drilled. Changes in static filtration on paper (API filtrate) did not correlate with filtration while the mud was circulated across rock. INTRODUCTION Oil additions to water muds have been reported to increase drilling rates, provide hole stability and improve filtration control. Eckel' showed that water-base emulsion muds used in the West Texas area increased drilling rate with increasing oil concentration up to 15 percent oil by volume, but drilling rate decreased at a concentration of 20 percent by volume. Based on laboratory tests using water muds to drill shale, Cunningham and Goins' reported that drilling rates increased and tendency for the bit to ballup decreased with the addition of oil. Percentage increase in drilling rate varied with the particular formation. They showed oil additions to improve drilling rates ap proximately 75 percent in Vicksburg shale and as much as 150 percent in Miocene shale. Each investigation showed an optimum oil content for the particular formation. Most data that indicated improved filtration control due to oil additions were based on static API Eltrates through paper rather than dynamic filtration through permeable rocks. Some types of dynamic test give a better representation of filtration down-hole while drilling and might be more likely to show some correlation with drilling rate. Static filtration would be important, of course, in relation to hole stability and formation damage. This laboratory's drilling tests, conducted on water-raturated Berea sandstone, indicated that improvements in drilling rate were not evident with increasing oil concentration in water-base muds. Investigation also showed similarity between oil-emulsion (water-in-oil) muds and water-emulsion (oil-in-water) muds while drilling these formations. In Lueders limestone high concentration of water-in-oil muds and high concentration of oil-in-water muds provided the same relative drilling rates. In Berea sandstone there was a large reduction in relative drilling rate with both the oil and water muds that contained low percentages of emulsified fluid. Dynamic filtration rates of water muds on rock did not always decrease with increasing oil percentages even though the static API filtration rates on paper did decrease. Data observed in laboratory drilling of limestone and sandstone indicate that improvements in field drilling operations when water- or oil-emulsion muds are wed may not be the result of increased drilling rates but of improved hole conditions. In some cases, actual drilling rates might be slower but improved hole conditions will result in less total time on the hole. DEFINITIONS Mud pressure—Pressure of drilling fluid as measured after leaving the drilling chamber. This is considered as the approximate mud pressure just past the bit and at the face of the formation. Terrastatic pressure—Pressure representing weight of overburden. Formation pressure—Pressure of formation fluid as measured at outlet of drilling chamber. This is considered as approximate pressure of fluid in the pores of the formation. Differential pressure—Difference between the mud pressure and formation pressure. Relative drilling rate, percent—Drilling rate with experimental fluid divided by drilling rate with water times 100 equals percent. LABORATORY EQUiPMENT AND TESTING PROCEDURES The drilling equipment has been described in previous publications The microbit drill is a closed system (capacity, approximately 7 gal) that can be pressurized to 15.000 psi and heated to 500F. Main components are a drilling chamber, filter-heater, rotary-drive and variable-speed cir-

By Heribert Wiedemeier, Ali Khan

The tetnperature-conposition phase diagram of the syste,n MnS-CdS has been investigated over a range fro)n 600° to 1000° C. The small degree of solid solution on the MnS rich slde cornpared to the large CdS rich single-plzase region could be esplained by the difference in strzrctures of the cotnponents and the relative sizes of the metal ions. The change in lattice parameter as a function of cot)zposition is linear atzd jollous Vegavd's rule within experittzental limits of error. Mns and CdS have gained considerable attention in recent years because of their interesting solid state properties. In order to investigate such properties and thermodynamic quantities of mixed compositions of transition metal chalcogenides, it is necessary to establish their phase diagrams. Two earlier publications are concerned with the MnS-CdS system. Schnaase' found complete miscibility when MnS and CdS were co-precipitated in aqueous solutions at room temperature. However, there is evidence that the mixed crystals were not stable over the entire range of composition. roger's' investigation of the ternary system ZnS-CdS-MnS at 900" C indicates a solution of 48 mole pct MnS in CdS. During the course of this work which covers a temperature range from 600" to 100O° C, emphasis has been placed on the use of high-purity materials and well-defined modifications of starting products. EXPERIMENTAL Starting Materials. The stable green modification of MnS with NaCl structure was prepared by direct fusion of the elements and by chemical transport reaction. Stoichiometric amounts of manganese of 99.99+ pct purity and of sulfur of 99.999 pct purity from Gallard-Schlesinger Corp. were sealed in an evacuated quartz tube at a pressure of 10"5 mm Hg and annealed for 48 to 60 hr at 800°C. The quartz tubes used throughout this work were outgassed under high vacuum at a temperature of 90OU to 1000° C for 12 to 18 hr. For the synthesis of MnS by chemical transport3 stoichiometric ratios of elemental manganese and sulfur and small amounts of iodine were sealed under vacuum in a quartz tube, which was placed in the temperature gradient, 900/800-C, of a two zone furnace. Single crystals of MnS in form of platelets and octahedra were deposited at the cooler end of the tube. The manganese content was determined by EDTA titratin. A typical result of several analyses was 63.05 pct Mn which agreed well with the computed value, 63.14 pct. Commercially available CdS of 99.9+ pct purity, a mixture of the cubic and hexagonal forms, was converted into the hexagonal high-temperature modification by annealing CdS under vacuum in quartz tubes at 700° C for about 36 hr. As a second method, cadmium sulfide was transported in a temperature gradient, 70O° /650" C, with in vacuo sublimed iodine from the hot to the cooler zone of the tube. Large sized crystals in form of hexagonal columns and some platelets were obtained. An average result of the cadmium analysis by EDTA titration4 was 77.93 pct in good agreement with the computed value, 77.81 pct. Only the NaCl modification of MnS and the wurtzite modification of CdS were used for the solid solutions. Preparation of Solid Solutions. Finely powdered MnS and CdS samples were thoroughly mixed in molar ratios and compressed into pellets of about 6 mm diam and 2 mm in height at a pressure of approximately 13,500 atm.

Jan 1, 1969