Search Documents

By Edward Sampson, Allan B. Griggs

Surveying of many holes drilled by the U. S. Bureau of Mines in the Metaline district has shown surprising deviations. The holes start in the Ledbetter slate (Ordovician) and pass into the underlying gently dipping Metaline limestone (Cambrian) at varying depths, locally in excess of 1000 it. All holes start vertical, but one had deflected as much as 35° at a depth of only 300 it. One hole was found to be deflected 70' at a depth of 1000 ft. These deviations were not indicated to the drillers by any action of the rods or machines. Analysis of the survey data in the light of the observed geology indicates that the holes deviate most in the Ledbetter slate and scarcely at all in the Metaline limestone. The upper part of the "limestone'" in most holes is a massive rock strongly altered by hydrothermal action and essentially homogeneous. The slate is only obscurely bedded but has a cleavage, varying from slight to strong, which is unrelated to bedding. Drill holes have deflected to become nearly perpendicular to the cleavage. Several plans and cross sections are submitted showing the behavior of various holes. Introduction The Metaline district of northeastern Washington has received much attention recently and has promise of becoming even more important as a source of zinc than at present. Exploration has been conducted largely by deep diamond drilling, and in the course of this work it was found that holes became seriously deflected. This paper deals with the nature and causes of these deflections. The district lies along the Pend Oreille River in the northeastern corner of Washington, about loo miles north of Spokane, 9 miles from British Columbia, and 15 miles from Idaho. Three mines are now in operation and for a number of years have furnished a considerable production of zinc and lead. The ore contains zinc and lead in a ratio of about 31/2 to I, and occurs in the upper part of the Metaline limestone of Cambrian age, the upper member of which, where unaltered, is a rather pure limestone. This is overlain by Ledbetter slate of Ordovician age. Ore has formed by replacement of limestone, commonly 100 to 200 ft. below the slate, in areas of gentle dip, resulting in extensive tabular ore bodies. In and near ore, limestone has been intensely altered to granular dolomite and fine-grained quartz, which, where it predominates, forms "jasperoid." As part of their war program, the Geological survey and Bureau of Mines of the U. S. Department of Interior have been cooperating in an investigation of the district. The exploration by the Bureau of Mines in 1943 and 1944 was conducted largely by deep diamond drilling in which as much as 1000 ft. or more of Ledbetter slate was penetrated before the ore-bearing Metalin-2 limestone was reached. During the course of this drilling it was found that holes were seriously deflected while traversing the Ledbetter slate.

Jan 1, 1949

The only definite information available is for the years 1875, 1878, and 1879 and 1880. The total figures in Table 48 are estimated. [ ]

Jan 1, 1942

By S. Harries Daddow

THE INSUFFICIENCY OF PILLARS OF COAL FOR THE PURPOSES DESIGNED-THE FRUITFUL CAUSE OF DANGER, EXPENSE, AND WASTE-THE PROOF OF INSECURITY-SUBSTITUTE FOR PILLARS OF COAL-PILLARS AND PANELS COMPARED. PILLARS of coal, which are designed and left in our mines as the means of supporting the overlying strata of our coal-beds, and securing protection to the miner, are not only insufficient for these purposes, but the most objectionable means of providing the desired security to life and property. Though such pillars are left at a great sacrifice to the owners of collieries and mineral lands, loss to the resources of the commonwealth, and ultimate privation to the public, they defeat the very ends for which they are designed, and not only do not secure life and property, but are as fatal to the one as ruinous to the other. Propositions.-It is eminently desirable that the resources of the commonwealth-particularly our mineral wealth in anthracite coal, which is limited-should be carefully utilized and made available, not only to ourselves but our posterity. Yet, speaking as an anthracite miner, we are wasting our resources of coal with a recklessness which will bring ruin in the end, unless checked, not only to the iron manufacturing interests of the East, whose chief protection, in competition with the iron-masters of the interior, lies in a cheap and abundant supply of anthracite furnace fuel, but to the best interests of the State. It is, consequently, not only desirable, but necessary, that we should realize every ton of coal from each colliery, and every acre of coal area, in order that our resources may not be wasted at present, to breed want in the future, and to realize the greatest present benefit to the mine, the miner, and the public. It is not possible, however, to secure these ends, if we continue to leave, as we do at present, from one-third to one-half our resources in anthracite as pillars in our mines. But our sad bills of mortality, our abandoned collieries, and our yawning mountain-sides, present ample evidence that even this enormous waste of coal, though left for the purpose of protecting life and property, is as totally inade-

Jan 1, 1873

By S. J. Kidder

Application of shrinkage stoping methods, without filling, in the mining of large silver-gold orebodies in the Mogollon district, where the ore is hard and wall rocks stand well without timbering and where veins make little water. Vertical and inclined shafts in use with both surface and underground hoisting stations. Storage pockets used on main hoisting levels, with electric signals and telephones for communication. Power is generated by De La Vergne engines having a total sea-level rating of 1540 hp. On account of the remote location of the camp, transportation is an important item of expense, amounting in 1922 to $0.641 per ton of ore milled or $0.265 per ton-mile on all freight hauled. THE Mogollon mining district is in the southwestern part of New Mexico near the southern end of the Mogollon range, from which the district takes its name. The town of Mogollon is but 37 1/2 mi. in an air line northeast of Clifton, Ariz. The air-line distance from Silver City is 52 1/2 mi. and from Tyrone, 57 mi. Supplies are transported by motor truck from Silver City. The distance by road is 75 mi., half of which is an improved highway of modern construction. Transportation has always - been a large item of expense in carrying on operations in the district. Valuable ore is said to have been discovered in the Mogollon Mountains as early as 1870 but the first regular prospecting was carried on in 1875, by James C. Cooney, a sergeant from Fort Bayard. His discovery of rich silver-copper ores in the region of Mineral Creek led to the establishment of the Camp of Cooney. Remote from any settlements where there was a semblance of law and order, and harassed by the Apaches, development was slow and nearly 10 years elapsed before the village of Mogollon was established on Silver Creek. Prospecting in this section of the district had disclosed the outcrops of several promising veins containing silver-gold ores. Among the early claims located were the Last Chance, Top and Confidence, on what has proved to be the most productive vein in the district.

Jan 3, 1924

The following is an incomplete list of members and guests who called at Institute headquarters during the period Apr. 10, 1919, to May 10, 1919. Arthur K. Adams, Spencer, Mass. Ensign Floyd D. James, U. S. S. Fulton. W. T. Bates, New York City, N. Y. J. Harry Johns, Thorsden, Woking, A. D. Brokaw, Washington, D. C. England. E. H. Clausen, San Francisco, Calif. W. F. Jones, Rock Springs, Wyo. W. M. Corse, Mansfield, Ohio. E. L. Lasier, Washington, D. C. E. O. Daue, Philadelphia, Pa. John M. Lovejoy, New Rochelle, N. Y. G. D. Dub, Washington,, D. C. 2d Lieut. James F. Magee, Lancaster, S. B. Eaton, Dover, N. J. Pa., Sherman Eaton, Smethport, N. C. Ernest Marquardt, Casper, Wyo. J. A. Endweiss, La Jolla, Calif. Geo. B. Marshall, Abangarez, Costa Edgar W. Engle, North Chicago, Ill. Rica. 2d Lieut. Maxwell E. Erdofy, New York Benj. L. Miller, So. Bethlehem, Pa. City, N. Y. Major Desaix B. Myers, Camp Mills. Chas. A. Fellencer, Allentown, Pa. Edmund Newton, New York City, N. Y. Arthur Feust, Joplin, Mo. Seely B. Patterson, Jr., Allentown, Pa. Ensign Harold P. Ford, U. S. S. Radnor. Wm. R. Pearson, New York City, N. Y. A. D. R. Galloway, Accra, West Africa. Harold C. Price, Langeloth, Pa. R. C. Gosrow, Milwaukee, Wis. T. C. Roberts, East. Orange, N. J. C. A. Grabill, El Paso, Tex. P. H. Royster, Washington, D. C. Hobart A. Hanks, San Francisco, Calif. W. H. Staver, New York City, N. Y. John L. Henning, Lake Charles, La. N. L. Wimmler, Bangkok, Siam. 1st Lieut. J. Parke Hook, Philadelphia, Capt. Jay P. Wood, New York City, Pa. N. Y. An item in the May Bulletin made it appear that Frank W. DeWolf had just become connected with the State Geological Survey of Illinois. This was one of the inadvertences of war. Mr. De Wolf has been Director, or Chief, of the State Geological Survey for approximately ten years. Through the courtesy of the Governor of Illinois, lie was loaned to the Bureau of Mines for about seven months, after which period he resumed his former position.

Jan 6, 1919

By William B. Plank

Mineral engineering student enrollment in U. S. and Canadian schools for 1955-1956 is 11,408, an increase of 11 pct more than last year. The undergraduate and graduate engineering students in both countries number 251,765, or 13 pct more than last year. These figures have been released by the American Society for Engineering Education. The largest increase in the undergraduate mineral engineering group in the U. S. is in ceramic engineering, with 676 students, or 31 pct more than last year. The next largest increase is in mining which shows a gain of 13.5 pct, compared with a gain of 13.1 pct in the total undergraduate enrollment in all engineering schools approved by the Engineers' Council for Professional Development. This figure is 190,355, which approaches the prewar figure. Metallurgical undergraduates increased 13 pct; geological, 5 pct; and petroleum, 2.5 pct. This year the figures for geophysics are combined with those for geological engineering, making a total of 1610 undergraduates, of which the geophysicists comprise about one seventh.

Apr 1, 1956

By Ferit Gurses

Extensive coal and lignite deposits exist in Turkey. Bituminous coal is the nation's principal mineral resource; important not only as fuel for the industrial development of the country, but also as a means of obtaining foreign exchange. Of the electrical power generated during 1939, 82.8 per cent was derived from coal.' It is anticipated that the lignite deposits will be one of the major sources of power for the electrification of the country. Bituminous Coal The locations of the four principal bituminous-coal2 basins are indicated on Fig. 1. The Eregli-Zonguldak basin lies on the Black Sea northwest of Ankara; the Canakkale basin lies near the junction of the Dardannelles; the Trakya basin is in European Turkey northwest of the Bosphorus and the Erzurum basin lies far to the east. The Eregli-Zonguldak basin is the most important of the four. This coal basin was discovered in 1829 but did not arouse interest until 1848; up to 1865, its annual production had not exceeded 50,000 metric tons. In 1865, during the Sultanate, working of coal mines was started by the Navy department, and the annual production was 61,145 metric tons. In 1908, the Minister of Commerce and Agriculture was authorized to develop the whole coal basin. Production reached 264,397 metric tons in 1910, and during 1915-1922, preceding the revolution, the total produc- tion of the basin was' 2,676,043, or an average of 334,000 metric tons annually. The period of national revolution that followed was marked by a steady increase in coal production in Turkey, although world production decreased, because of the crisis of 1929-1932, about 52 per cent. ARea and Geology of the Coal Basin The geology of the Eregli-Zonguldak area is not yet completely known. The basin begins -at Gungazi, to the west of Eregli, and extends to Sogutozu, a distance of about 106 miles. The coal beds, however, appear only in places and the overlying Cretaceous strata hide them elsewhere. This area includes the most important centers, such as Kandilli, Alacaagzi, Teflenli, Kozlu, Gelik (see Fig. 2). The geological sequence of the district is correlated with the Cretaceous of the Balkans; which is, in turn, a prolongation of the Alpine zone. Geological surveys made by G. Ralli, R. Zeiller and P. Arni3 show that the Eregli-Zonguldak formations fall into three natural divisions. Series a, The Alacaagzi in the district of that name (Fig. 2), is of the Culm stage. The strata strike generally east-west and dip about 30" south. This series appears also around Kandilli and Camli, with a steeper angle of dip, but the deposits there lack regularity. The Alacaagzi stage appears also farther east, to the south of Kozlu and Gelik. The Alacaagzi series contains 15 seams of an average thickness of 2 ft. of good coal. Series b, the Kozlu, best represented in Zonguldak, Kilimli, Catalagzi, and between

Jan 1, 1944

By R. A. L. Black

Rock mechanics is a very new science. It has been accepted as a recognized discipline for some two decades, but it is only within the last five to ten years that it has been common to include the teaching of rock mechanics as a separate subject in undergraduate curricula at universities. Thus, few senior mining engineers practicing in industry, either men in charge of production or those engaged in mine planning and design, are familiar with the subject. That this unfamiliarity has continued so long is also due in part to the fact that the results of rock mechanics investigations have been published in a large number of different periodicals covering subjects ranging from experimental stress analysis to obscure branches of applied earth sciences. The first really useful textbook ' in the English language was published only in 1965, in Canada. It made available to students and to practicing engineers, for the first time in concise form, the essential body of accepted knowledge about rock mechanics and developed the theories on which it is based in a simple, clear and logical manner. Another factor which has resulted in rock mechanics science being slow to be accepted by the mining industry is that research work has often appeared to be esoteric and unpractical. Senior engineers have been reluctant to spend money on the application of new knowledge when the process of application seemed uncertain and ill-defined, and where the cost of field investigations (which is necessarily high) appeared to offer no certainty of economic reward. This is a reasonable attitude on the part of mining engineers; they are responsible to skeptical boards of directors whose chief concern is, very properly, the net return on capital invested. The application of rock mechanics science has not in the past,

Jan 1, 1968

By N. Brown, H. Green

The effect of quenching temperature and of aging temperature and time on compression stress-strain curves of ß brass was investigated. Age softening occurs at a rate which decreases with decrease of quenching temperature below the critical temperature for ordering. The activation energy for softening is 15,400 cal per mol. No matter how rapidly brass is quenched or what the temperature from which it is quenched, practically complete order is obtained at room temperature. It has been demonstrated that with respect to the specific heat,',' electrical resistivity," X-ray diffraction, and microstructure, the slowly cooled and rapidly quenched specimens are the same and that complete long range order exists in both cases. However, Smith" showed that the hardness of ß brass depended upon the cooling rate and the temperature from which brass is quenched. Smith showed that the hardness was a maximum for specimens quenched from about 445 °C and that the as-quenched structure softened at room temperature at a rate depending upon the temperature prior to quenching. This softening after quenching is in this paper referred to as age softening. The results of this investigation are qualitatively the same as the findings of Smith. However, a more detailed analysis of these phenomena has been possible since the stress-strain curve offers a more sensitive index of the state of the metal than hardness. It is the purpose of this paper to show how the mechanical properties are related to the ordering of ß brass. A 200-lb ingot made from electrolytic copper and electrolytic zinc was extruded to 1/2in. rod. Chemical analyses at frequent intervals along the rod showed that the alloy contained 51.5 pct Cu with the greatest impurity being iron, at 0.01 to 0.001 pct. To obtain a constant test material, the 1/2in. extruded rod was warm-rolled to % in. diameter at 200°C and then recrystallized to a grain size of 2.0 mm. The specimens for the compression test were % in. high and % in. in diameter. The specimen ends were polished on 600 metallographic paper and coated with Molykote for a lubricant. The compression rig consisted of an anvil resting on the machined table of the Baldwin Southwark testing machine and a plunger fixed to the movable cross

Jan 1, 1954

By C. R. Sandberg, C. A. Connally, N. Stein

This paper describes the results of volumetric efficiency tests on oil well pumps handling gas oil mixtures. The work was performed in a large scale, above ground unit wherein test conditions could be accurately controlled and measured. The main variables studied were gas/oil ratio (including gas from solution and free gas mixed with oil), pump compression ratio, pump stroke length, pump speed, and clearance volume between the valves at their closest approach. Results are presented for two different pumps and for oils of two viscosities. Relatively small amounts of gas entering the pump resulted in large decreases in volumetric efficiency. Under conditions where the pump was operating at reduced efficiency because of the presence of gas, it was found that variation in the clearance volume between the standing and traveling valves had a considerable effect on pump efficiency level. This effect of the valve clearance volume was found to be significantly altered by the viscosity of the oil used in the tests. The effects on pump efficiency of the other variables studied were found to be relatively small over the range of conditions utilized. INTRODUCTION The production of oil by pumping is often hampered by low volumetric efficiency. A direct increase in lifting costs results from low volumetric efficiency. An indirect increase in lifting costs, probably greater than the direct increase, results from additional wear and tear on pumping equipment and from the down-time necessary for the repairs which can be traced to low-efficiency operation. Both increases in lifting costs tend to reduce economically recoverable oil. A number of different factors can contribute to low pump efficiency. A known basic cause of low efficiency is the presence of free gas in the pumped fluid. Pump volumetric efficiency is calculated only on the basis of liquid pumped and because any free gas pumped is discounted, this volume of free gas would represent a loss of pump efficiency. However, gas also causes a reduction in pump efficiency because it is a highly compressible fluid. It is known that pumps some- times "gas lock" because of excessive gas-to-liquid ratios in the pump barrel. Little is known of the role of gas compressibility in the intermediate case where the pump is operating at low efficiency. The opinion exists, however, that oil-well pumps tend to operate at higher efficiency with long stroke lengths at low speeds, but no quantitative studies of these pumping variables have been reported. It was believed that a much better understanding of the variables which control pump volumetric efficiency could be obtained and that possibly some suggestions as to the methods for increasing efficiency might be found from a study of the operation of pumps handling gas under closely controlled conditions. Previous investigators have studied the effects on pump efficiency of such factors as oil viscosity, oil temperature, slippage of oil. past pump plungers, pump submergence, valve size and spacing, pressure above pump plunger and fluid vapor pressure. However, none of these published investigations were conducted with pumps being subjected to large amounts of gas such as might be the case in a pumping well, nor did any of the investigations study the effect of variation in stroke length or pump speed. A large-scale teat unit was therefore constructed for studying the operation of pumps handling gas and for evaluating effects of such variables as pump stroke length and pump speed. PROCEDURE AND EQUIPMENT A schematic diagram of the pump testing equipment is given in Fig. 1. A 45-ft length of 6-in. casing is mounted vertically in a 65-ft tower. Sight ports are mounted in the casing at intervals near the location of the pump intake and the liquid level in the casing. These sight ports are fitted with Lucite windows sealed by neoprene "0" rings. The Lucite windows are machined to conform to the I.D. of the casing so that no obstruction to flow is present along the casing wall. The casing is fitted with a tubing head and 2-in. tubing is hung inside the casing. Pumps are seated in a shoe attached to the 2-in. tubing. A 1-in. polish rod is attacked directly to the pump without any intervening sucker rods. The top of the polish rod is attached to the weight carrier, which contains a number of weights to be used to force the polish rod in against tubing pressure on the down-stroke. This is necessary because a long string of sucker

Jan 1, 1953

For the first time in the history of shaft sinking, the concept of mid-shaft loading has been used. By making use of available hoisting capacity during drilling periods, development work on underground hoist chambers and ore-pass and ventilation by-pass systems at Vaal Reefs South gold mine is being done simultaneously with sinking. This factor, together with the unusual configuration and design of the twin-shaft system at Vaal Reefs South, and the use of raise borers in the installation of ore-pass and ventilation by-pass systems, will mean that the shaft will be commissioned at least a year earlier than would have been possible had conventional methods been used. The possibilities of mid-shaft loading in reducing the time normally taken by shaft service development were recognized by Anglo American Corp. consulting engineers and Shaft Sinkers Pty. Ltd., the company which is sinking both shafts at Vaal Reefs.

Jan 1, 1970

By Schneider, W. G.

IT is not my purpose to burden you with many statistics. The charts herewith should be considered merely as indicating the trend. I believe' that is what is really of interest to us. It is difficult, if not impossible to forecast with any assurance future developments, because of possible new mines, competitive materials, curtailment' or increase in the use of the metal in certain markets, and many other factors that have a vital bearing on any industry. Fig. 1 shows United States smeltet output of copper, starting with 1845. It is estimated that in 1928 the smelter output of copper will be about 1,010,000 tons. Between 1895 and 1905 it increased about 200,000 tons, and between 1905 and 1915 about 240,000 tons. Between 1915 and 1925 the increase was about 140,000 tons. This is an average increase over 30 years of about 190,00Q tons per ten-year period. At the present time the indications are that this demand for increased production will continue. As to whether or not we have the supplies or facilities to maintain this increase or a greater one, remains to be seen. Provided it is possible for United States smelters to increase their production, they should be producing at the rate of about 1,210,000 tons or more per year by 1935.

Jan 1, 1928

CHARLES KIRCHHOFF, Chairman. ALBERT SAUVEUR, Vice-Chairman. A. A. STEVENSON, Vice- Chairman. HERBERT M. BOYLSTON, Secretary, Abbot Bldg., Cambridge, Mass. John Birkinbine, J. Esrey Johnson, Jr., Felix A: Vogel, William H. Blauvelt, William Kelly, Leonard Waldo, James Gayley, Richard Moldenke, William R. Walker, Henry D. Hibbard, Joseph W. Richards, William R. Webster. Henry M. Howe, E. Gybbon Spilsbury, Frederick W. Wood. Robert W. Hunt, A. A. Stevenson is appointed an additional Vice-Chairman of the Committee. He will serve as Acting Chairman during the absence abroad of Professor Sauveur. For the meeting of the Institute which is to be held in New York City, Oct. 16 and 17, 1913, the following papers are now assured

Jan 7, 1913

By D. A. Dahlstrom

In the paper, a comparison was made between flowsheets using the screen bowl centrifuge and disc filters, respectively, as the primary dewatering device. The authors very effectively show that by raising feed temperature, mechanical dewatering is enhanced through reduced viscosity of the water. When a final coal moisture of 10% is required, the net effect of heating the feed is a reduction in thermal requirements because of the lower evaporated load on the dryer. The flowsheet comparison on this, however, was not completely correct. Disc filters do not generally utilize enhanced mechanical dewatering through increased temperature. Horizontal belt filters, through the optimal use of steam heating of the filter cake, have shown significant cost reductions over disc filters where steam is not used. In addition, the authors forgot to mention that there is a certain fraction of the feed that is so fine that it cannot be recovered by the centrifuge economically. That is the function of the filtration device shown in [Fig. 4]. In subbituminous pipeline coals, this fraction represents more than 10% of the feed. Even after flocculation and belt pressing, the moisture content in the fine fraction is 30%-40. Recent tests on a subbituminous pipeline coal slurry, compared an Eimco-Extractor horizontal belt filter with the screen bowl centrifuge flowsheet shown in [Fig. 4]. Mechanical dewatering was enhanced through the use of a steam dry zone after the initial dewatering zone. Vacuum pump horsepower was reduced by more than 50% through the use of condensers, and heat recovery was utilized to minimize thermal costs. Thermal drying to 10% moisture by weight was required in both flowsheets. The 0.5 wt% fines in the filtrate were flocculated and recycled to the filter, thus eliminating the belt press and solids mixers. When the three major operating costs (which normally account for 50%-75% of the coal operating costs) of steam, electricity, and flocculants at current prices were calculated, the flowsheets utilizing the Eimco-Extractor had cost savings vs the centrifuge flowsheet of 89c/t (81c per st) of surface dry coal. This advantage increases with increasing thermal and electricity prices. I congratulate the authors for the strides made with the screen bowl centrifuge. However, filtration flowsheets continue to be improved and their simplicity and low thermal and electrical requirements should not be so quickly dismissed.

Jan 1, 1984

US 4,181,520 - Direct reduction of iron oxide ore to sponge iron in a rotary kiln. Ore is fed into the kiln along with coal briquettes and passed through a preheating zone and then a reducing zone countercurrent to the flow of a kiln atmosphere which includes air or other oxygen-containing gas. The agglomerated coal is heated at such a rate that it disintegrates into fine particles in the preheating zone. The coal is largely recovered for reuse, while reduction is effected with a reducing flame rather than the coal. G. Reuter and W. Schnabel, assigned to Metallgesellschaft AG. Jan. 1, 1980. 6 pp. (75-36). Filed- 10-19-78 (952,870). Priority: West Germany, 1-14-75 (2,501,182). Same: British 1,532,969, dated Nov 22, 1978.

Jan 1, 1982

By H. E. Rorschach

Activity in Oklahoma fields declined in 1938 from the banner year of 1937. During the year, 1768 wells were completed as compared to 2632 completed during the year 1937. The following tabulation sets out details regarding the wells completed during the year: These computations do not take into account the wells drilled for repres-sure and salt-water disposal, and other nonexploratory wells. Purchasers' reports filed with the Corporation Commission of the State of Oklahoma show a total of 168,789,229 bbl. of oil purchased from Oklahoma leases in 1938, or a daily average of 462,436, a decrease of about 25 per cent from the year 1937. The outstanding operation of the year was the further development of the Ramsey pool, in western Payne County, the producing horizon being classified as the Wilcox. This pool was discovered on the last day in the year 1937, by the Mid-Continent Petroleum Corporation drilling on a unitized block in see. 18, T. 18 N., R. 2 E. The map in Fig. 1 shows the development at the end of the year 1938. An important discovery of the year was the Champlin Refining Company's No. 1 Boehm, in Garfield County, sec. 4-24N-8W., the producing horizon being the second Wilcox found at a depth of approximately 6700 ft. This pool was assigned the name of Hillsdale. Some of the offsets to this discovery well had not come up to expectations at the end of the year, but the discovery seems to be important as indicating that the Wilcox sand is productive in the Anadarko Basin area, providing that the right structural conditions are present.

Jan 1, 1939

By J. R. Sturgul, J. C. Wynn

Computers and computer applications in geophysics are fairly recent innovations. The area of data handling is one that has found many immediate applications. Initially, the use of computers involved in almost all cases, a batch-input arrangement requiring a trip to the local computer center, a wait and another trip. Even though the computer worked at incredible speeds, the time-delays, in case an error in the input data developed, often could be several days. Use of computers in mining exploration by medium-sized or small-sized companies and contractors has been almost non-existent beyond simple data reduction work. The principle J. R. Sturgul, SME member, and J. C. Wynn, both affiliated with the Dept. of Geosciences, University of Arizona, Tucson, presented this paper at the Eleventh International Symposium on Computer Applications in the Minerals Industry, reasons appear to be the time factor and the inconvenience of the frequent trips involved. With the advent of time sharing systems, whereby a company need only have access to a terminal, the main objections can be overcome. An Apparent Solution An apparent solution to the time and distance inconveniences which would permit more extensive use of computers in geophysical exploration, is to buy or lease/purchase a medium-sized computer and install it in or near one's office. This is a formidable proposition in terms of cost and programming time on both respects, but several mining companies of larger size have already gone this route. In most cases, the computers have been expensive devices with a limited memory or core size. For routine data handling this memory size is not restrictive; however, for many geophysical applications such as three-dimensional modeling this can be critical.

Jan 10, 1973

By George M. Humphrey

It is indeed a pleasure for me to have this opportunity to discuss with you a subject which I find infinitely interesting and intriguing - namely, world-wide iron ore supply and demand. We will be examining the following: (i) current iron ore production and requirements; (ii) the major ore producing countries; (iii) the seaborne iron ore trade; (iv) ore grades or types; and (v) future requirements. For those who may not be familiar with the iron ore mining industry, it may be useful to know at the outset that our industry has been plagued with overcapacity for the past seven years. The optimism which prompted substantial expansion of productive capacity in the early to mid-1970's has unfortunately proved to have been unfounded. I shall begin by describing where we are today as well as a little about how we got there. In the latter regard, it's not so much that historical knowledge will solve any of the industry's problems or provide clairvoyance with regard to the future. Rather it's a feeling on my part that some knowledge of the past will provide a useful perspective capable of enhancing our analysis of future trends. At the time of writing, the most recent year for which we have definitive world-wide iron ore production and consumption statistics is 1980. In that year the world consumed approximately 859 million metric tons of iron ore to produce approximately 510 million metric tons of primary iron consisting of 502 million tons of pig iron and 8 million tons of sponge iron. Crude steel production for the same period attained a level of 719 million metric tons. Because it is possible in today's world to produce steel without consuming iron ore simply by melting scrap, the key statistic insofar as iron ore demand is concerned is primary iron production. In 1980 the ratio of iron ore consumption to primary iron production was 1.68:1.00. The comparable ratio over the past seven years has varied from 1.63 to 1.87 and averaged 1.72:1.00. All the same, as a practical matter crude steel production and iron ore consumption tend to parallel one another closely, and for the time being a good rule of thumb is that to produce an average ton of crude steel requires 1.20 tons of iron ore. Let's turn our attention now to the regions where the 859 million tons of iron ore necessary to support 1980 world-wide iron and steel production were produced. Not surprisingly, most of the ore was produced in the same region where it was smelted. In round numbers 65% of the world's iron ore production is currently consumed in the same general region as it is produced, while 35% enters the seaborne trade and is transported in ocean vessels to a more remote consuming area. Approximately 85% of the world's seaborne iron ore trade is directed to the Western European and Japanese markets, both of which are almost entirely dependent on off-shore sources for their mammoth iron ore requirements. The following tabulation lists, in order, the twelve leading iron ore producing countries in 1980 as well as their percentages of total and free-world production; in addition their export potentials are presented. As a group these countries accounted in that year for 89% of world-wide production which stood at 871 million tons. Leading World Iron Ore Producing Countries [ ] One will first note that world iron ore production is dominated by the top four producers - namely, the U.S.S.R., Brazil, Australia and the U.S.A. - which together accounted for nearly 60% of total 1980 production. Of these four major producers the U.S.A. and the U.S.S.R. produce almost exclusively for consumption in their own regions, whereas Australia and Brazil produce primarily for the seaborne export trade. In fact Australia and Brazil accounted for about 50% of all seaborne iron ore trade in 1980! It is also interesting to note that Australia, Brazil, the U.S.A. and Canada accounted for nearly 60% of free world iron ore production in 1980. Once again the importance of Australia and Brazil shows itself, with their share alone of free world production reaching 35%. As has already been noted, a significant 35% of the world's iron ore production in the year 1980 was

Jan 1, 1982

Jan 1, 1882