Search Documents

By N. W. Perry

Some months ago a gentleman gave me a handful of minerals which he had collected in an arroyo, or dry stream-bed, that ran through the town of Ramos, State of San Luis Potosi, Mexico, as a sample of the class of ore that might be expected in the mines of that section. I was, however, familiar with those mines and their ores, and cast the pebbles aside as of no interest. I afterwards returned to Mexico and took charge of two groups of mines, one in the State of Zacatecas, and the other in the town of Ramos, State of San Luis Potosi. While I was thus engaged, it was a very frequent occurrence for parties to bring me specimens of rock, ores, etc., for my opinion on them; and one day a man brought me a half-dozen or more small pieces of a very black shiny mineral, desiring to know what it was. I did not recognize it, and desired him to give me the specimens for analysis, which he promised to do in a day or two. He never did give them to me, for he lost them ; but he said there were plenty more where these came from—at Ramos—and he could get them at any time for me. I thought no more of the matter until after my return to this country, when, one day, in looking over some of my old " trash," I came across the specimens at first referred to as having been cast aside so carelessly. I noticed two distinct minerals among the pebbles : one being erubescite or tetrahedrite, the predominating mineral of the mines of Ramos, and the other a hard black shining mineral, the same that I had wished to analyze in Mexico. On testing for hardness I was surprised that it scratched topaz with some degree of ease, thus placing it above 8 in the scale of hardness. Trying it with a corundum, I sometimes succeeded in scratching it, but at other times it would scratch the corundum, and at still other times neither would produce the slightest effect on the other. Crystallized topaz would be ground to a powder in attempting to scratch the black mineral, without abrading it in the slightest. It must, therefore, be placed at 9 in the scale of hardness. It is of the deepest opaque black, not unlike pitch-blende in ap-

Jan 1, 1884

By Nicholas J. Grant, Oliver Preston

A series of dilute solid solutions of a1uminum and silicon in copper, in powder -form, were internally oxidized, compacted, and extruded, to produce Cu-A12O3 and Cu-SiO2 alloys with 0.1 to 12 vol pct of oxide. Room-temperature tensile tests, creep-rupture tests from 450oto 850°C. conductivity measurements, and recrys-tallzzation studies were made. Oxide particle size and interparticle spacings were determined in an effort to relate the structure to measured strength values by means of known dispersion strengthening theories. A new dispersion strengthening theory, based on the effect of the dispersed phase on the retention of strain energy from the deformation step, zs proposed for this type of alloy, THE study of dispersion strengthening is of partitular interest in high-temperature materials technology in view of the excellent creep-rupture Properties and thermal stability achieved with SAP.1-5 Considerable effort has been devoted to this study in recent years, and encouraging results have been obtained in a number of systems.6 In general, the most

Jan 1, 1962

By R. A. Swalin

IN this paper, the results of an investigation concerning the diffusion of three elements, magnesium, silicon, and molybdenum, in nickel are presented. The work represents a continuation of a diffusion program relating to solute diffusion in nickel. The program has the dual aim of obtaining useful diffusion data and of yielding insight into the factors governing solute diffusion in close-packed metals. The first paper of this series has been published earlier? In both investigations, in agreement with recent results from other laboratories, the activation energies for solute diffusion were found to be close but not identical to that of self-diffusion in the pure solvent in question. In order to obtain valid diffusion data, certain experimental pitfalls recognized only in recent years had to be avoided. Chief among these were the necessity for minimizing short-circuiting diffusion paths such as grain boundaries and the necessity for using low solute concentration gradients. In this series of investigations the following precautions were taken in an attempt to minimize such errors. 1) Samples with large grain sizes, 0.5 to 10 mm, were prepared. 2) The diffusion coefficients were measured at relatively high temperatures, since imperfections such as dislocations play a less important role at such temperatures than at lower temperatures. 3) Alloys containing less than 1 atomic pct were chosen for study. Experimental Work Materials—A diffusion couple technique was employed in the experimental investigation. Briefly, this technique consisted of the following. A diffusion couple was fabricated by placing a flat face of a cylindrically shaped alloy disk against a similar face of a pure nickel disk, and a bond was formed at an intermediate temperature under pressure. The diffusion couple thus fabricated was subjected to a diffusion anneal at higher temperatures for a measured period of time and then sectioned perpendicular to the direction of diffusion. After analyzing the sections for solute concentration the diffusion coefficient was determined from a probability, plot of concentration vs distance from the diffusion interface. Vacuum melted Mond nickel was used in the experimental program. The chemical analysis of this nickel is listed in Table I. Alloys used were prepared

Jan 1, 1958

By E. S. Wheeler

THE conversion plant of the Climax Molybdenum Co. is at Langeloth, Washington County, Pennsylvania, approximately 30 miles west of Pittsburgh. The molybdenite concentrates converted originate in the company's mine and mill at Climax, Colorado.1 They are delivered to the Langeloth plant by rail packed in 175-lb. bags. War production of concentrates at the mill started in 1918 but it was not until about 1920 that any peacetime uses of the metal began to develop. Early conversion of Climax concentrates was mainly into ferromolybden um, produced for the company by a custom smelter. CHRONOLOGY OF PLANT DEVELOPMENT In 1924 a small hand-rabbled roaster was built at Langeloth, the roasted concentrates being used principally in the production of calcium molybdate by a conventional wet method. The size of the original plant is indicated by the fact that during 1925 about 400,000 lb. of molybdenum was converted. In 1925-1926, a multiple-hearth roaster was erected (12-ft. o.d. 8-hearth Nichols-Herreshoff); also the first experimental ferromolybdenum was produced at Langeloth. At this time calcium molybdate was produced in the furnace by a process to be described. With continued interest in and increased use of molybdenum, it was necessary to arrange for enlargement of plant facilities. Although only one 12-hearth 16-ft. o.d. roaster was erected at this time (1929), plans were prepared for a duplicate unit, which was completed in 1935, giving a potential roasting capacity of some 16,000 lb. Mo per day under the then prevailing roasting practice. Shortly after this second unit had gone into production, increased demand overtaxed the plant, and as a result two 12-hearth 18-ft. o.d. roasters were placed in operation in 1936 and 1937. This gave the plant a potential roasting capacity of 40,000 to 50,000 lb. Mo per day, and necessitated major changes in auxiliary handling equipment as well as improved facilities for producing ferromolybdenum. Following the introduction (1938) of a new product-molybdic oxide briquets and because of the constantly growing demand for molybdenum, plant facilities were again enlarged in 1940 and 1941 by the erection of two 16-hearth 18-ft. o.d. roasters. These two new units, along with a change in roasting practice, brought the potential roasting capacity to 150,000 to 190,000 lb. Mo per day, based on about 15 lb. per sq. ft. of hearth area. Other departments of the plant have necessarily grown, until today the plant is modern throughout and completely mechanized, with equipment geared to produce marketable products as follows:

Jan 1, 1944

By M. J. Duggin

Evidence is produced below to show that the carbide "Mn,C," reported by Kw,and ersson' is really a mixture of two carbides. One is an Fe-Mn carbide which is probably isomorphous with hexagonal Mn15C4, reported by Bouchand and Pruchart.' The othev is a tetragonul Fe-Mn carbide with cell dzmensions close to those reported previously by the author3 for an Fe0.1Mno. carbide. IN a recent investigation several Fe-Mn carbide specimens, each weighing about 5 g, were prepared in a manner previously reported.3 Debye-Scherrer X-ray photographs were taken of at least two samples from different parts of each specimen using a 114.6-mm-diam camera. The exposure time was 2 hr using filtered chromium radiation, a tube voltage of 35 kv and a tube current of 10 ma. In the case of one specimen, which contained nominal weight percentages of iron, manganese, and carbon of 9.40, 84. 6,, and 6.0, respectively, duplicate chemical analyses indicated f1.2 and 5.5 wt pct C to be present in the two samples taken of the specimen: no graphitic carbon was detected. One powder-diffraction pattern of this specimen indicated the presence of the tetragons: carbide reported earlier,3 (a = 6.772A, c = 9.427A), plus cementite (O), plus an unknown structure. The second powder-

Jan 1, 1970

By R. J. Quigg, G. S. Doble

Commercial stress -relieved TD Nickel bar was shown to retain room- and elevated-temperature tensile strength after exposure up to 2501°F. Cold swaging increased both room -temperature and 2000°F tensile strength. After annealing at 2500°F the strengthening due to swaging was retained at 2000°F hilt eliminated at room temperature. Annealing produced changes in hardness and X-ray half peak width indicating the presence of recovery processes as 1071° as 1000°F but no recrystallization of swaged material was noted at any temperature. In contrast to swaging, rolling induced a recrystal-lized structure after annealing. The tensile strength of this recrystallized structure was comparable to the cold-worked condition. High-temperature tensile properties of as -received bar were highly anisotropic with the transverse tensile strength being one fifth the longitudinal value. The aniso-/ropy is affected by working direction and may he partially reversed by changing the direction of metal flow. The divergence in tensile strength, beginning above 550°F or- approximate one third the absolute melting point, is strain-rate dependent. T D Nickel is a commercial dispersion-hardened alloy containing 2 vol pct thoria. The dispersion, consisting of spherical particles 0.030 to 0.050 in diameter with an interparticle spacing of less than 1 is reported to maintain stable properties up to 2400°F.1 This stability of second phase results in maintenance of elevated-temperature strength at higher temperatures and longer times than normal nickel-base superalloys.2 The purpose of this paper is to describe the effect of various mechanical working operations on the strength and microstructural stability of TD Nickel bar. MATERIAL AND PROCEDURES All material used in this study was commercial TD Nickel bar. This material is produced by a chemical process which results in a nickel powder containing a dispersion of thoria particles. The powder is then pressed, sintered, extruded, and subsequently worked to bar stock. Three starting materials from three separate lots were used: as-extruded bar. 1-in.-diam stress-relieved bar, and 1/2-in.-diam stress-relieved bar. Since TD Nickel bar stock is cold-worked without a recrystalliza-tion anneal, the accumulated deformation or degree of cold work in these materials increases as the bar diameter decreases. Some of the 1/2-in.-diam bar was swaged to 1/4 in. diameter at room temperature in order to produce an as-worked condition for comparison with the stress-relieved stock. Tensile testing was performed on an Instron Tensile Tester at a constant crosshead speed of 0.020 in. per min. The 0.2 pct offset yield strength was measured from the load-crosshead movement plot. Specimen gage dimensions were 0.080 in. in diameter by 0.40 in. in length, producing a strain rate of approximately 0.050 min-1. Specimens were tested in air and heated within a resistance-wound furnace controlled to ±5°F. A 15-min soak at temperature was employed before testing. Samples were heat-treated in air and specimens machined after exposure with sufficient material removed to eliminate any surface contamination. X-ray line breadth was determined from a diffractometer scan of a transverse face of a bar using copper K, radiation. Metallographic preparation utilized standard mechanical polishing with Carapella's etch. Specimens for electron microscopy were electropolished in a 1:7 sulfuric/methaol solution and chromium-shadowed collodion replicas prepared. RESULTS AND DISCUSSION I) Effect of Elevated-Temperature Exposure on the properties of TD Nickel. The effect of various elevated-temperature exposures on the room-temperature tensile strength of TD Nickel is shown in Table I. In the unexposed condition the tensile strength, reduction in area, and hardness all increase with increasing accumulated deformation while the elongation decreases. After exposure at 2500°F the strength of all three materials decreases to about 65,000 psi and the elongations increase slightly. The apparent increase in strength of the 1-in. bar after a 2000°F treatment is probably experimental scatter. These results indicate that the room-temperature strengthening due to additional deformation is annealed out upon elevated-temperature exposure. In contrast to the room-temperature data, the 2000°F tensile strengths increase in order of increasing deformation even after exposure. Although some loss of strength occurs after exposure, much of the effect of working is still maintained at 2000°F. The room-temperature hardness after various

Jan 1, 1965

By J. L. Bruce

For a number of years, from an economic standpoint, the ventilation of the Colorado mine of the Davis-Daly Copper Co. has been a difficult problem. The development through the main hoisting shaft was pursued for a number of years and to a depth of about 2500 ft.( 762 m.)before large bodies of good commercial ore were opened up. This lack of early success in exploration restricted expenditures for ventilation, with the result that the present orebodies were opened up at a depth of 2500 ft., and in country rock f relatively high temperature, without adequate means f supplying the development faces and the stopes with cool or fresh air of low humidity and suitable velocity. During the progress of development, two or three connections were made at higher levels with the workings of adjoining operations, but these were of a makeshift and unsatisfactory character and afforded no means for carrying downcast air from the surface, in anything approaching a direct course, to the working faces. During the latter part of 1917, arrangements were made with. the Anaconda Copper Mining Co., whereby, during the year 1918 and the early part f the year 1919, a crosscut was driven eastwards on the 2500-ft. level of the Colorado shaft and connection was made by means f an up-raise of approximately 200 ft. to a crosscut driven westwards from the 2800-ft. level of the Belmont mine, this crosscut at the top of the raise being driven at Davis-Daly expense by the Anaconda Copper Mining Co. This connection, in conjunction with a No. 11 Sirocco fan installed near the Colorado shaft, provided the Colorado mine with a maximum of approximately 30,000 cu. ft. per min. of relatively fresh air, most of which came in a fairly direct route from the downcast Belmont shaft through the No. 11 fan to the 2500-ft. level stopes. After passing through these stopes and the stopes of overlying levels, it passed through the main crosscuts on higher levels back to the Colorado shaft, which provided the upcast for this current of air. The improvement

Jan 9, 1921

By Gordon B. French

Occidental's in situ retorting process for oil shale has many advantages over the conventional, underground mine and surface retort. Only a portion of the oil shale is mined and transported outside where it blends with the oil-shale talus found in the area. Spent shale is retained underground without surface disposal problems. The process consumes no water from outside sources. Noise and dust levels are kept at a minimum. As many of the facilities as possible are located underground. More oil is produced from a given area than conventional surface processing. Additional energy can be recovered by using conventional turbines to generate electrical power of magnitude of three to four times required by the operation.

Jan 1, 1977

By D. Gupta, S. Weinig

This investigation comprises the study of dislocation-oxygen interactions in a! titanium and its effect on the ductile to brittle transition in titanium. Internal friction techniques using a low-frequency lorsion pendulum were used to study the oxygen atom interactions with dislocations in "superpurity" titanium. A calculation of the interaction energy between an oxygen atom and a dislocation, based on the "breakaway" strain resulted in a value of 0.015 ev as compared to theoretical values of 0.022 and 0.035 ev for edge and screw dislocations, respectively. Both the saturation of the room temperature decrement and the transition from ductile to brittle behavior occurred at 1.5 at. pct 0. It was proposed that the embrittlement was due to oxygen atoms immobilizing the dislocations. It was possible to increase the ductility of the Ti-0 binary alloys by decreasing the oxygen pinning. The increase in uniform elongation was 30 pct for an increase in the preanneal temperature of 300°C. ThE room-temperature ductility of a titanium is significantly affected by interstitial solutes. Although oxygen has a solid solubility of 15.5 pct by weight, the room-temperature ductility extends only to 0.6 pct.' The ductility precipitously falls at this concentration and the fracture characteristics change from ductile to brittle.2 The small effective bulk composition of solute required to destroy the room-temperature ductility of the titanium must be indicative of an in-homogeneous distribution of solute atoms. Internal friction techniques were used in this investigation to

Jan 1, 1960

By T. M. Dr. Drown

(Read at the Philadelphia Meeting, February, 1878.) ZINC is, as is well known, very brittle at a temperature of about 210° C. (410° F.), and may then be readily pulverized in a mortar. By sifting it may be obtained of uniform grain. I have been accustomed to prepare products passing through 40, 60, and 80-mesh sieves, and also by bolting through a fine handkerchief. The principal analytical uses to which I have hitherto applied this material are to the reduction of iron directly from the ore by heating it with the pulverized zinc, and the reduction of ferric to ferrous compounds in solution. In the first case the pulverized ore, 0.5 gram or less, is intimately mixed with about ten times its weight of the pulverized zinc (the finer the zinc the better), in a porcelain crucible, and this mixture is covered with about the same amount of zinc. The crucible is then heated at the top of the flame of a Bunsen burner, at a dull red heat, for about ten minutes. The crucible should not be covered. When cool, the crucible, with its contents, is placed in a flask treated with hot dilute sulphuric acid, and brought quickly to a boil. The zinc and reduced iron are dissolved in a few minutes and the flask is then tightly corked and allowed to cool. When cool, the iron is directly titrated by potassium permanganate.

Jan 1, 1878

By P. Somasundaran, Y. H. C. Wang

A detailed study of carrier flotation of kaolin clay using calcite showed the major beneficiation mechanism to be enhanced aggregation between anatase and calcite under intense agitation conditions. To develop an understanding of this selective aggregation, surface charge characteristics of kaolinite, anatase, and calcite were studied under simulated flotation conditions. Zeta potential of all these minerals tended towards a constant negative value in oleate solutions under certain conditions possibly due to adsorption or precipitation of oleate on them. However, whereas the zeta potential of anatase in the oleate solutions was not influenced by the agitation level, that of kaolinite was found to be strongly dependent on the agitation intensity. The effect of oleate on zeta potential of kaolinite was reduced by an increase in agitation intensity. It is suggested that oleate is much more firmly bound to the surface of the anatase and that this preferential attachment is responsible for the enhanced selective aggregation of the anatase with calcite. Agitation level plays a major role in carrier flotation since intense agitation is considered to enhance both the chemisorption of oleate on anatase and preferential detachment of calcium oleate precipitate from the kaolinite surface, all of this producing a large difference in the surface Properties of anatase and kaolinite, and hence in their tendency to aggregate with calcite.

Jan 1, 1983

By Paul J. Sirkegian

A detail of the guide rollers is shown on Fig. I; and Fig. 2 shows a photograph of a guide roller that has been in service for several months on the haul-back cable. The former practice of supporting and guiding the haul-back cable on slusher hoists at Kimberly was accomplished by using the conventional type of snatch-block pulley, but it was found that an excessive amount of cable whipping and unreasonable wear on both rope and pulley resulted from this type of cable support. The guide, which is wholly made in the Corporation's shops, consists of two vertical and one horizontal roll assembled in a frame that is lagged to the cap timber in a slusher drift. In some slusher drifts more than one guide-roller assembly is used, depending upon the length of the drift. The installations usually are placed at 30-ft. intervals. We have found by actual experience that these rollers have increased the life of the haul-back cable approximately 200 per cent, as compared with the usage of the conventional sheave-block pulley. Cable Care The underground rigging crew and the slusher operators are trained in rope splicing. No cable clamps or knots are permitted on slusher cables and all cable "eyes" are spliced. The standard practice has been to use preformed cables of ?-in. diameter for haulage and ½-in. diameter for the haul back. The preformed cables have proved to be important factors for safety in use and speed in making splices. No external lubrication is used on the cables. It has been found that dry ropes have about 400 per cent longer life than those that were lubricated under these operating conditions. An accurate record is kept of all cable life and the tonnage moved by the slushers in each working place, and if the rope wear is excessive in any particular working place, an investigation is made to determine the reason. Wire-rope Sling for Snatch-block Anchor The rope sling is shown by Figs. 3 and 4. These slings support the snatch-block pulley for the haul-back rope. The standard practice at Kimberly is to use a roller-bearing snatch-block pulley 10 in. in diameter. The snatch-block housings are equipped with a clevis attachment in preference to swivel hooks, as it has been found that the more rigid clevis keeps the cable in better alignment. The snatch blocks are hung from the cable sling, which is wrapped around the posts of the drift sets as shown on Fig. 3. This method of anchoring the pulley provides better anchorage and flexibility than those of the rigid or spring-mounted types. When the slusher-drift headings are being advanced, the snatch blocks are hung from a "gin" pole ahead of the last set of timbers' An employee is assigned on each production shift to take care of the lubrication of all slusher hoists that are being used and he is provided with tools for minor repairs.

Jan 1, 1946

By C. F. Quest

THE steel industry has a definite need in its tonnage mills for a formula relating expected tensile strength to the analysis of the steel. The McWilliam-Barnes1 and other less comprehensive formulas are used for this purpose, but these formulas were designed for an analysis range that does not include the medium manganese and silicon-bearing steels. This type of steel is being produced to meet the demand for tensile strength slightly higher than that of ordinary structural steel but not high enough to justify expensive alloy steels. The purpose of this paper is to present a somewhat more compre-hensive formula based on data accumulated over a number of years by the Inland Steel Co., and to discuss the method followed in obtaining a formula to fit the data. The resultant formula admittedly is still weak in some respects, but for the expanded analysis range appears to be an improvement over the other formulas. It is hoped that with the collec-tion of more data and possible collaboration with other mills studying this problem it will be possible to work out a more nearly perfect formula. Several publications have been issued on this subject. In some, the equation type of relation was evolved while others made a combina-tion of tables and an equation. The latter include work by Campbell2,3 and Webster.4,5 Campbell classified the steels as acid and basic and applied a different formula to each. For basic steels, he used the equation: Tensile strength = 41500 + 770C + 1000P + yMn [1] y was a variable depending on the carbon and manganese content of the steel and was listed in tables, Webster investigated acid Bessemer steel and developed the equation Tensile strength = 38000 + 800C + xP + yMn [2]

Jan 1, 1940

By Henry N. McCarl

Lightweight aggregates include a variety of mineral and rock materials used to provide bulk in concrete building units (block), light- weight structural concrete, and precast concrete units, as plaster aggregate, insulating fill, and other structural and/or insulation purposes. They are distinguished from other mineral aggregate materials by their lighter unit weight- 80 to 100 pounds per cubic foot (pcf) or less for loosely packed lightweight aggregates as compared to 125 pcf or more for crushed stone, sand, gravel, air-cooled slag, and other more common mineral aggregates. The various lightweight aggregate materials may be classified into four groups as follows: 1) Natural Lightweight Aggregate Materials-prepared by crushing and sizing natural rock materials such as pumice, scoria, tuff, breccia, and volcanic cinders. 2) Manufactured Structural Lightweight Aggregates-prepared by pyroprocessing clay, shale, or slate in rotary kilns or on traveling grate sintering machines. 3) Byproduct Lightweight Aggregates-prepared by crushing and sizing foamed and granulated slag, cinders, and coke breeze. With the exception of processed slag, this group is becoming less important as time passes. 4) Manufactured Insulating Ultralight- weight Aggregates-prepared by pyroprocessing ground vermiculite or perlite. This chapter will focus on the use of natural lightweight aggregates and manufactured insulating ultralightweight aggregates, and both the production and use of manufactured structural lightweight aggregates with some comments on byproduct materials. Detailed discussion of the production and use of both expanded and air-cooled slag is presented in a separate chapter in the utilization section of this volume, and there are separate commodity chapters on vermiculite, perlite, pumice, and volcanic cinders. Discussion of the commodities covered elsewhere in the book will be limited to observations on their utilization and relation to other lightweight aggregate materials. All materials considered as lightweight aggregates are derived from some initial natural raw material. While historical definitions have included such organic materials as straw and peat as lightweight aggregates, the discussion in this chapter will restrict itself to lightweight aggregates derived from mineral or rock materials. Thus while the actual lightweight material in use may be a manufactured product, it is derived from an ore or raw material that is obviously a mineral resource. In this context, then, the reserves of raw materials for lightweight aggregate use may include iron ore and flux stone (the components of blast furnace slag) as well as coal (the raw material from which cinders are derived) as well as those clay, shale, and slate deposits that display the characteristics of bloating or controlled expansion when subjected to elevated temperatures (1600 to 2400°F.).

Jan 1, 1975

Jan 1, 1914

By D. E. Menzie, D. L. Dauben

This paper discusses the physical parameters involved in the slow flow of high molecular weight polymer solutions in porous media. The interacting effects of polymer properties and porous media properties on flow performance are considered. Experiments were conducted with the polyethylene oxides, with molecular weights ranging from 200,000 to over 5,000,000. Frontal advance velocities ranged from I to 30 ft/day. The porous matrix consisted of a flow cell packed with glass beads. Polymer solutions were characterized by viscosity and normal stress measurements. Under certain conditions, unexpectedly high flow resistance was observed. This behavior was observed to be a function of flow rate, pore size, polymer molecular weight and concentration. The polymer solutions exhibit "dilatant" flow behavior in porour media in contrast with the pseudo-plastic behavior in simple flow systems. A theoretical ex-planation of such behavior is presented. INTRODUCTION The use of polymers in the injected water of a waterflood increases oil displacement efficiency by reducing the mobility (k,/pu) of the driving phase. A reduced driving phase mobility results in improvements in the areal sweep efficiency and in the vertical coverage in stratified reservoirs. This mobility reduction may be achieved by a permeability reduction, a viscosity increase or by a combination of the two. Early attempts at increasing the injected water viscosity were not successful because of the poor economics involved. The use of such materials as glycerin, sugar or glycols to increase water viscosity was not economically feasible. Attempts in using certain naturally occurring polymers were not too successful because of the high polymer losses to the rock. A high molecular weight, partially hydrolyzed polyacry-lamide was introduced 3 years ago as a waterflood additive.',' Initial work by Pye' indicated that the presence of these polymers in dilute concentrations decreases the water mobility 5 to 20 times more than would be expected from measurements of the solution viscosity. Such an effect would be of obvious economic value since only a small polymer concentration would be required to accomplish a large reduction in water mobility. This research was designed to study the basic flow mech anisms of polymer solutions in porous media. The interacting effects of polymer properties and porous media properties on flow performance are considered. This study indicates some of the conditions under which these interactions can lead to significant mobility effects. is valid only for Newtonian fluids. For polymer solutions and other non-Newtonian fluids the equation must be modified to consider that viscosity is a variable quantity. Modification of the Darcy equation to include non-Newtonian effects has been the subject of several recent investigations."" The modifications generally adopt a rheological model. such as an Ellis or Dower law model. to Dorous media by defining some characteristic channel radius. Most of these studies showed the porous media flow behavior to be predictable from viscometric data. Investigations involving the flow of high molecular weight polyacrylamide solutions through cores have generally encountered the high flow resistances reported previously by Pye. This high flow resistance has generally been attributed to an in-depth permeability reduction, as evidenced by a reduced permeability to water which has displaced polymer solution from the porous media. Marshall and Metzner" report high flow resistances, which they attribute to viscoelastic effects. In this paper, the effects of polymer molecular weight, pore size, flow rate and concentration are considered. The polymers used are the polyethylene oxides known as Poly-ox. This class of polymers was used because of its availability in a wide range of molecular weights and because of its known ability to propagate well through porous media. THEORY PHYSICAL PROPERTIES OF POLYMER SOLUTIONS The polymer molecule dissolves in water by means of hydrogen bonding, but retains some of its own structural identity while in solution. Nonionic polymers, such as polyethylene oxide, are generally considered to have a random coiling configration. This type of molecule has the ability to "sequester" or hold a large volume of solvent within its coils in a manner similar to that of a sponge. The random coil is easily deformed and under an applied stress

By R. Al-Hussainy, P. B. Crawford, H. J. Ramey

The effect of variations of pressure-dependent viscosity and gas law deviation factor on the flow of real gases through porous media has been considered. A rigorous gas flow equation was developed which is a second order, non-linear partial differential equation with variable coeficients. This equation was reduced by a change of variable to a form similar to the diffusivity equation, but with potential-dependent diffusivity. The change of variable can be used as a new pseudo-pressure for gas flow which replaces pressure or pressure-squared as currently applied to gas flow. Substitution of the real gas pseudo-pressure has a nrtmber of important consequences. First, second degree pressure gradient terms which have commonly been neglected under the assumption that the pressure gradient is small everywhere in the flow system, are rigorously handled. Omission of second degree terms leads to verious errors in estimated pressure distributions for tight formations. Second, flow equations in terms of the real gas pseudo-pressure do not contain viscosity or gas law deviation factors, and thus avoid the need for selection of an average pressure to evaluate physical properties. Third, the real gas pseudo-pressure can be determined numerically in term of pseudo-reduced pressures and temperatures from existing physical property correlations to provide generally useful information. The real gas pseudo-pressure was determined by numerical integration and is presented in both tabular and graphical form in this paper. Finally, production of real gas can be correlated in terms of the real gas pseudo-pressure and shown to be similar to liquid flow as described by diffusivity equation solutions. Applications of the real gas pseudo-pressnre to radial flow systems under transient, steady-state or approximate pseudo-steady-state injection or production have been considered. Superposition of the linearized real gas flow solutions to generate variable rate performance was investigated and found satisfactory. This provides justification for pressure build-up testing. It is believed that the concept of the real gas pseudo-pressure will lead to improved interpretation of results of current gas well testing procedures, both steady and unsteady-state in nature, and improved forecasting of gas production. INTRODUCTION In recent years a considerable effort has been directed to the theory of isothermal flow of gases through porous media. The present state of knowledge is far from being fully developed. The difficulty lies in the non-linearity of partial differential equations which describe both real and ideal gas flow. Solutions which are available are approximate analytical solutions, graphical solutions, analogue solutions and numerical solutions. The earliest attempt to solve this problem involved the method of successions of steady states proposed by Muskat.' Approximate analytical solutions' were obtained by linearizing the flow equation for ideal gas to yield a diffusivity-type equation. Such solutions, though widely used and easy to apply to engineering problems, are of limited value bemuse of idealized assumptions and restrictions imposed upon the flow equation. The validity of linearized equations and the conditions under which their solutions apply have not been fully discussed in the literature. Approximate solutions are those of Heatherington et al.. MacRobertsl and Janicek and Katz.' A graphical solution of the linearized equation was given by Cornell and Katz. Also, by using the mean value of the time derivative in the flow equation, Rowan and Clegg' gave several simple approximate solutions. All the solutions were obtained assuming small pressure gradients and constant gas properties. Variation of gas properties with pressure has been neglected because of analytic difficulties. even in approximate analytic solutions. Green and Wilts8 used an electrical network for simulating one-dimensional flow of an ideal gas. Numerical methods using finite difference equations and digital computing techniques have been used extensively for solving both ideal and real gas equations. Aronofsky and Jenkins"I " and Bruce et al.11 gave numerical solutions for linear and radial gas flow. Douglas et al." gave a solution for a square drainage area. Aronofsky 13 included the effect of slippage on ideal gas flow. The most important contribution to the theory of flow of ideal gases through porous media was the conclusion reached by Aronofsky and Jenkins" that solutions for the liquid flow case'" could be used to generate approximate solutions for constant rate production of ideal gases. An equation describing the flow of real gases has been solved for special cases by a number of investigators using numerical methods. Aronofsky and Ferris 10 onsidered linear flow, while Aronofsky and Porter 17 considered radial gas flow. Gas properties were permitted to vary as linear functions of pressure. Recently, CarteP 18 proposed an empirical correlation by which gas well behavior can be estimated from solutions of the diffusivity equation using instantaneour values of pressure-dependent gas

Jan 1, 1967

By Rossiter W. Raymond

THE lead-mining industry of Missouri, as of other parts of the Mississippi basin, appears to have been paralyzed by the shock of competition with the mines of the States and Territories further west. It is difficult for establishments working galena ores, too poor in silver to pay for extracting it, to compete with the producers of the argentiferous carbonates of Utah and Colorado, who look upon their lead as a byproduct of little value, and are satisfied if it pays the charges of transportation, or the loss in smelting for silver. But simultaneously with this depression in the lead-mining of the Mississippi States, the development of new zinc deposits has caused a notable revival in the mining of zinc ores. There has recently been a sudden and strong rise in the price of spelter, which, though probably to a large extent temporary in character, has given important encouragement to prospectors and miners. Apart from the general recovery of business in the United States from the prostration of the past six years, the cause of the advance in spelter has been the falling off in production, resulting from the shutting down of several leading Western works,-the Martindale and Carondelet works, at St. Louis, and the Consolidated Company in Kansas. At the same time, the principal works at La Salle, Ill., were undergoing repairs, and produced less than usual, while the sheet-mill of Matthieson & Hegeler, at that place, was running as usual; so that this concern, ordinarily a large producer, entered the already depleted market as a buyer. These causes are in their nature transitory, and it is quite likely that spelter will be superabundant in a few months. Having lately received from a well-informed Missouri corres¬pondent some samples of the zinc ores and a general account of the ore deposits of Southwest Missouri, I have thought that it might interest the Institute to examine these specimens, and to hear such brief statements concerning the region as I am able, upon good authority, though without the aid of any personal investigation on the spot, to give. The zinc-bearing territory in Southwest Missouri appears to be very extensive; that is to say, zinc ores have been mined during the last year at various points throughout a district extending from the eastern edge of Kansas, west of Joplin, to a line some 50 miles east

Jan 1, 1880

By C. S. Herzig

In the Engineering and Mining Journal of Jan. 27, 1900, there appeared an article by Fred T. Greene, describing a method of measuring stopes by the use of strings, a clinometer and a tape. In the early part of 1899 I had occasion to use a somewhat similar method, for the purpose of accurately ascertaining the volume of a very irregular drift connecting two mines. This drift was an important factor in a lawsuit for $150,000, in which it was necessary to determine accurately the volume originally occupied by the material extracted from the drift. While it is unnecessary to give all details of the controversy, some explanation of the conditions is required for a clear understanding of the following description. This drift was started by the a E." Co. from its workings, in about 7 ft. of ore, and headed toward the " G " property, the plan being to extract all the ore between foot- and hanging-walls, but to take out nothing but ore. As the " G." workings were approached; the ore-body became very irregular and much thinner. It was, however, very closely followed, and where the drift broke through into the " G." workings, the hole was only 11 inches high by 14 inches wide, or just about the size of a man-hole in a boiler.. Thus, this connection-drift tapered sharply; and the very irregular foot-wall sloped toward the " G." workings, and entered them at a place where the stope was only about 3 ft. high, and the ground had already commenced to cave. It may be added that the ore-body was a nearly flat deposit of lead carbonate in limestone, the ore and gangue being quite soft. I was called upon by the " G." people to make the survey

Jan 1, 1901

By Robert W. Hunt

THE memorable features of American history have been making fast during the last century, and notably so since 1860; and they are by no means confined to political or to any one branch of scientific development. Of all the industrial arts, none show a greater change or a mightier progress than the Bessemer manufacture. And this year, while we are celebrating the first centennial of our national life, we can also celebrate the first decennial of American Bessemer practice. While not forgetting or undervaluing what has been done in other countries, I have thought that a brief history of the introduction and development of the Pneumatic or Bessemer process in America would be of interest. In 1863 the Kelly Pneumatic Process Company was formed and an arrangement entered into with William Kelly, who had taken out letters-patent of the United States, Nos. 16,444 ; 17,628, re¬issued as 505; 18,910, dated January 10th, 1857 ; June 23d, 1857; November 3d, 1857; and December 22d, 1857, respectively. This association was composed of the Cambria Iron Company, E. B. Ward, Park Brothers & Co., Lyon, Shorb & Co., Z. S. Durfee, and, later, Chouteau, Harrison & Valle joined the combination. Not satisfied with possessing the control of the Kelly patent, they sent Mr. Z. S. Durfee to England, to secure for this country Mushet's patent on recarburization, No. 17,389, dated May 26th, 1857, the same having been taken out in England on September 22d, 1856. In this Mr. Durfee was successful. Previous to the application of William Kelly for a patent, Henry Bessemer, of England, had taken out patents dated February 12th, 1856, and August 25th, 1856, in this country. Kelly claimed priority in the discovery of the principles of the process, and the Patent-office allowed his claim by granting him his patents. In the autumn of 1862 Mr. Alexander L. Holley, while in England, was impressed with the importance of Mr. Bessemer's inven¬tion, and so fully foresaw its future, that, upon his return to the United States, he induced Messrs. John A. Griswold and John F. Winslow, of Troy, New York, to join him in endeavoring to possess Bessemer's American patents. Mr. Holley returned to England in

Jan 1, 1877