Search Documents

By Edwin C. Barringer

IRON and steel scrap has again become page one news, as it was during the war. To many this is anomalous because the common concept is that the theaters of war are literally paved with scrap as the by-product of war damage and abandoned materiel. To an extent this is true, the bottleneck being the ferreting out and transportation of this scrap. While you as consumers of the electric-furnace grades of scrap-the premium grades-are concerned primarily in only one segment of the scrap market, I believe you ill be interested in a general discussion of the market with subsequent funneling down to your specialty.

Jan 1, 1947

By S. S. Clarke

THE opening of zinc-lead ore bodies in the lower chert beds of the Tri-State district, locally called sheet-ground deposits, [ ] presented several new economic operating problems to be solved before the low-grade deposits could be mined profitably. Drilling was the first high-cost problem and loading and haulage difficulties followed. At this time, the sheet-ground mines are producing about 2000 tons per day. GEOLOGY The geology and ore deposits of the Tri-State district have been covered in detail by [ ] Fowler and Lyden.* Briefly, the sheet-

Jan 1, 1942

By John Primrose

Tube stills having demonstrated their usefulness for refining operations, the later developments in their design have been in the direction of improved thermal efficiency. The earlier designs operated with low furnace temperatures and large volumes of furnace gas because the fuel was burned with much excess air. It was quite possible to provide sufficient heating surface to lower the temperature of the flue gas to within 150" of the temperature of the inlet oil, or when inlet-oil tempera-tures were high to have the flue gas escape at 300" or 350" F. by using the heat remaining in the flue gas from the still to preheat the air supplied for combustion. But even so, the thermal efficiency was low because of the large quantity of air used for combustion. The large quantity of excess air was required to burn the fuel in the furnace at a temperature low enough to prevent overheating the furnace walls and overheating of the oil. Supplying heat to the tubes of the heating surface at a rate beyond the capabilities of the oil to absorb, except with a considerable difference between the temperature of the inside of the tube and oil passing through, would result in overheating the tubes and the oil in contact with them. For these reasons it was very necessary in the older types of tube stills to burn the fuel with large quantities of excess air, resulting in low thermal efficiency despite the low flue-gas temperature. Neglecting loss by radiation, the thermal efficiency could be improved only by burning the fuel with less excess air, but it was necessary to accomplish this without upsetting the furnace temperature conditions existing when large quantities of excess air were used. There are several methods of bringing this about, such as controlling the furnace temperature by returning a proportion of the flue gas to the furnace, or by exposing direct to the fire a heat-absorbing surface so located and proportioned that sufficient heat will be absorbed by radiation to prevent excessive furnace temperatures.

Jan 1, 1928

By E. H. Burdick

THE difficulties inherent in table concentration operations as applied to gold, silver, lead and zinc ores, are accentuated in the scheelite mill, which has a flowsheet that is similar in general principles. The narrow "spread" in the specific gravity between scheelite and the usual gangue in which it occurs often makes its clean separation extremely difficult and in some cases impracticable. The problem is further complicated by the extreme friability of the mineral and its inordinate tendency to "slime," particularly where fine grinding is necessary and wet grinding methods are employed. The physical aspect of the occurrence of scheelite in the ores, the kind and character of the rock in which the mineral is present, its hardness, friability and the specific gravity of its constituents, as well as like characteristics of the associated minerals-pyrite, pyrrhotite, sphalerite, and others, all have a bearing on the successful milling of crude ores and the production of a concentrate that is marketable with minimum price penalty or none at all. Most tungsten deposits are considered low grade when the limiting factor of low percentage recovery by gravity methods is borne in mind. The great majority of deposits developed or in process of development carry from 0.4 to 1.0 per cent tungstic oxide. Ore carrying I per cent is considered good grade; 0.7 to 0.8 per cent, fair, and below that figure, low grade. Steady mill feed averaging upward of 1.0 per cent W03 is exceptional. Inasmuch as buying specifications demand a 60 per cent W03 content, the mineral content of the ores as mined must be concentrated to at least that degree. A few companies have constructed chemical plants for the treatment of their complex concentrates and low-grade flotation product, but the smaller operator must rely on table concentration, borrowing the tools and to a large extent the methods of his predecessors in the gold, silver, lead and zinc mills. Whether these are the best tools and methods that can be devised is an open question. Except in rare instances, table concentration, however carefully conducted, does not yield a satisfactory final recovery of the mineral content in headings as indicated by chemical determinations of tungstic oxide content. A saving of 60 to 65 per cent is considered fair, and an average 80 per cent recovery, exceptional. Each scheelite ore body is a separate problem. Details of handling that give best results in one case may not be successfully operative at a property on the same contact zone and but a short distance removed. Supplementary treatment of tailings by flotation may be successful in producing a low-grade concentrate of around 15 per cent WO3, which is adapted to further treatment chemically at a given property and entirely unsuccessful at another. This problem constitutes another of the unanswered questions. The following paragraphs relate solely to the beneficiation of scheelite ores by table concentration and supplementary methods.

Jan 1, 1942

By O. D. Gonzalez

ThIS communication presents the results of a determination of the permeabilities of hydrogen and deuterium in a iron from 360° to 560°C. Recently Heu-mann and primas' have given values of the diffusivity and solubility in a iron of the two isotopes from which the permeability can be calculated. The work reported in the present communication, however, is a direct measurement of the rate of permeation of the isotopes through an identical iron specimen under the same conditions, so that systematic errors can be minimized in the calculation of the ratio of the permeabilities—the value which is usually of main importance in establishing limits for isotopic differences in diffusive processes. Experimentally the procedure used was the usual one: a steady-state flow of gas produced by a pressure difference across an iron membrane was observed as the pressure rise with time in a previously evacuated, calibrated volume connected to the outlet side of the membrane, while a constant pressure of gas was maintained on the opposite inlet side. The membrane was a cylindrical tube 9.38 cm long, 0.730 cm inside diam, 0.187 cm wall thickness, fabricated of 99.95 pct vacuum-melted National Research Corp. iron (less than 0.003 pct C). One end was sealed by a heliarc-welded iron (99.95 pctj lid of 0.147 cm thickness; the other end of the tube was welded to a 304 stainless-steel tube (0.318 cm ID and 0.318 cm wall) which connects to a vacuum system and to the calibrated volume including a dibutylphthalate manometer. The temperature of the iron membrane was maintained constant to ±0.l°C and was measured with an iron-constantan thermocouple which was calibrated against a standard Pt/Pt-Rh thermocouple: the temperature variation along the length of the membrane did not exceed ±0.5°C. Hydrogen was allowed to pass through the membrane assembly for 72 hr at 615°C before permeability measurements were begun. The system was tested at temperature before and after the experiments by a substitution of helium for hydrogen in the inlet side; under these conditions the pressure rise observed in the outlet side was negligible at all times. The gases used for the permeability measurements were 99.95 pct Matheson prepurified H2 and 99.7 pct D2 (0.3 pct HD) from the Isomet Corp. The gases were dried with liquid N2 before use. In Fig. 1 the logarithms of observed flows, jt, for a pressure difference of 73.4 cm Hg are plotted against T-1 Each point in Fig. 1 represents the slope determined by a least-square evaluation of a plot of the pressure in the outlet side of the membrane against time, including at least two separate sets of observations. Each point in the figure has an uncertainty of ±0.6 pct arising from the experimental uncertainty in the pressure and time measurements. The standard deviation of the observed pressures from the straight lines in all cases is less than the experimental precision of the measurements. The observed flow, jt, includes a small but not negligible flow through the stainless-steel connection.

Jan 1, 1968

Jan 1, 1921

By L. G. E. Bignell, E. A. Hanson, J. O. Lewis

There was a general upward trend of all petroleum activities in Oklahoma during 1933, especially in the last quarter, though the average price for crude oil for the year was below 1932 and overproduction in East Texas demoralized conditions for several months. As the Federal Agencies established under the National Industry Recovery Act began to function conditions in Oklahoma were visibly affected and production of "hot oil" from Oklahoma City field practically ceased. More oil wells were completed, six new fields discovered, extensive geophysical prospecting carried on in many parts of the state, and an increased amount of clean-out and reconditioning work done in older pools during the past year. To increase quantity and rate of recovery of oil many wells producing from limestone formations were treated with hydrochloric acid. The Oklahoma City field had a reported production of 66,984,570 bbl. of oil during 1933, or almost exactly twice the amount reported for 1932. Potential tests and other indicators show that the wells are rapidly approaching the stage where mechanical lift must be applied to all of them, including the wells in the Wilcox sand zone. The major pipe-line companies serving the oil fields of Oklahoma have been anxious to make connections to all wells during 1933 and have indicated a willingness to accept all oil available. The amount offered has been restricted by proration orders, but the state did produce 178,356,-449 bbl. during the year, an increase of about 18.6 per cent over 1932. This increase was practically all due to the greater demand for Oklahoma City oil, as all other pools of any importance showed loss in production or very small gains last year. The U. S. Bureau of Mines' laboratory reports the lubricating distillate content of Oklahoma City crude from Arbuckle and Lower Simpson formations about 17 per cent by volume. East Texas oil is reported to contain about 5.6 per cent lubricating distillates. The desire of the transportation companies to keep their equipment operating at maximum capacity and the need of some refineries for more

Jan 1, 1934

By C. van der Poel, R. L. Chuoke P. van Meurs

When an initially planar interface between two im-ttitcihle liquids is displaced at constant rate, U, nor-mat to the front, instability will occur for all rates greater than a critical rate. U, given by provided the Fourier decomposition of the spatial pertmrbcrtiott or deformation of the moving displacetment front contains modes with wavelengths. A, greater than a critical wavelength, given by tit there expressions, p, p and k, with the subscripts I and 2 distinguishing the two 1iquids under consideration, are density, viscosity and effective pemeability coefficients respectively; g is the absolute value of the acceleration due to gravity; and cos (zz') is the direction cosit7e between the vertical carlesian coordinate z' (positive upward) and the z coordinate norma1 to the initially plane macroscopic interface taken positive in the direction from Liquid I to Liquid 2. U is the average volumetric velocity (injected volume of liquid pet. unit time per unit of area normal to Z) and is positive for Liquid I displacing Liquid 2, negative for the reversc displacement and r2 is an effective inter-fucial tension (for displacements between parrallel plates, t0= s the ordinary bulk interfacial tension). further, there is a wavelength of maximum instability given by For natural perturbations, this wavelength will preclotninate and characterize the form of the instability as a quasi-sinusoidal deformation, i.e., viscous fitzgers of peak-to-peak separatiotr, A,,. Comparison of experitient with theory rei'eals tltat these considerations are recsonably valid for displacements in hoth parallel plate chantzels and nnconsoli-clutt'd glass ptnvder packs. These results are. tij particular interest for interpretation of data from laboratory experiments with regard to fielil applica/iotz.s. It is quite possible for A,, although st7zall relative to the large lateral dimension of the reservoir, to rxceed the greatr.st lateral extent of the lahoratory sample or model. If it does, frontal displace- ment occurs in the laboratory experiments, and oil INTRODUCTION Thc puposes of this paper are to present theoretical and experimental evidence for occurrence of macroscopic instabilities in displacement of one viscous fluid by another immiscible with it through a uniform porous medium and to compare available experimental data with some predictions of a theory of instability developed by the first author. The instabilities are referred to as macroscopic in the sense that spatially quasi-sinusoidal, growing fingers of the displacing liquid are formed, the width and peak-to-peak separation (wavelength) of which is large relative to a characteristic length of the particular permeable medium such as grain size. Visual models of two kinds have been used to obtain observations: displacement of oil by water-glycerine solutions through the flow channel formed by closely spaced parallel plates and displacement of oil by water with and without initial interstitial water through unconsolidated glass powder packs, employing the technique of matching indices of refraction. In all cases we have observed macroscopic instabilities or fingers under conditions predicted by the theory to be favorable for their occurrence. The phenomenon discussed here is not the production of streamers due to gross inhomogeneities such as permeability stratification of the porous medium. It is our object to show, on the contrary, that a quantitative prediction of finger spacing is possible in a porous medium known to be macroscopically homogeneous and isotropic throughout. The importance of the phenomenon in its influence on the configuration of oil and water with respect to oil production behavior was noted earlier by Engel-berts and Klinkenberg' who coined the term "viscous fingering". THEORY Necessary and Sufficient Conditions ior Instability anc Initial Kinematics There are several levels of increasing complexity in the theoretical description of instabiIity of fluid displacements in permeable media. Of these, the simplest description, ;tdapted to low permeability systems, is selected for presentation.' More inclusivc tlescriptions are reserved for separate publication.

By G. C. Stone

IN common with many members of the Institute, I was much interested in Mr. Kent's paper on " Manganese Determinations in Steel," * read at the Virginia meeting. Having recently had an opportunity to collect a similar series of results for spiegel, I venture to offer them to the Institute, hoping that they may also prove of interest. Sample No. 1 was taken at our works, where the spiegel was made,

Jan 1, 1883

By I. H. Pratt

The results of a study on the preparation of thin-film capacitor structures are discussed. The dietectric source material was quartz which was sputtered and deposited onto aluminum electrodes and counter-electroded to complete the metal-oxide-metal structures. This configuration was utilized to evaluate the dielectric, the device characteristics, and related process parameters. The effect of gas sputtering pressure, magnetic field strength, source-to-substrate distance, and power density on the rate of deposition is shown. Increased film thickness uniformity over a 3 by 3 in. area by optimum substrate positioning is indicated. Dielectric constant, dissipation factor, dielectric breakdown strength, insulation resistance, heat treatment, capacitance, and dissipation over the range 400 Hz to 5 MHz are reported. In the fabrication of silicon-integrated circuits, silicon dioxide has found use as a material suitable as a diffusion mask, for surface passivation of the silicon, and for protection of conductive films used for interconnections. Its use as a dielectric for thin-film capacitors in film hybrid circuits has been limited, to a degree, for lack of a compatible processing technique and because of its relatively low dielectric constant. With the recent advent of practical metal-oxide-semiconductor (MOS) field effect devices, the material is now being used to insulate the gate electrode from the conducting channel in the silicon. In this latter application, more stringent requirements have been imposed on .the oxide. A comprehensive resume of the use of silicon dioxide in integrated silicon device technology has been compiled including oxide film and bulk properties, method of oxide formations, and their applications.' A relatively new process to deposit SiO, and other dieIectrics is by rf sputtering, and the purpose of this paper is to describe the behavior of capacitors fabricated with a dielectric which has been sputtered from a quartz target and to indicate the relative effect of several of the process parameters on the film deposition. Work on rf sputtering of SiO2 and other dielectrics has been reported utilizing a triode type of sputtering system as described herein or a diode self-sustained glow discharge system. 2-8 SPUTTERING The process occurs during an electrical discharge in a gas plasma which provides the ions for acceleration to the target to produce the desired sputtering. The necessary plasma can be generated by a dc glow discharge through application of a high potential between two electrodes at approximately 2 to 10 x 10-2

Jan 1, 1969

By Roger A. Harris

INTRODUCTION The Kidd Creek Mine produces a total of 3.6 million tons annually. Geologically the orebody is complex, containing rich values of zinc, copper, silver and lead which are mined and milled as two separate "ore types". Production is mainly from highly mechanized sub-level open stopes of approximately 300,000 tons each. The Mine Engineering Department has developed, and now operates, a computer system that is the subject of this report. It was created specifically to aid the daily work of the mining engineer and has features that are new and possibly unique in the industry. DESIGN OBJECTIVES In 1971 a task force, set up to investigate the subject of computer assistance to mine engineering, specified four design requirements which it felt a successful application had to satisfy. They were:- 1) The computer had to offer a TOTAL SYSTEM that was fully integrated into the routine mine engineering function. 2) The computer had to be directly usable by the current engineering staff, the majority of which had received no formal training in computing.

Jan 1, 1977

By Chester A. Rowland, David M. Kjos

Mineral ore comminution is generally a feed preparation step for subsequent processing stages. Grinding, the fine product phase of comminution, requires a large capital investment and frequently is the area of maximum usage of power and wear resistant materials. Grinding is most frequently done in rotating drums utilizing loose grinding media, lifted by the rotation of the drum, to break the ores in various combinations of impact, attrition and abrasion to produce the specified product. Grinding media can be the ore itself (autogenous grinding - primary and secondary), natural or manufactured non- metallic media (pebble milling) or manufactured metallic media - steel rods, steel or iron balls. This chapter covers rod and ball mills which utilize manufactured metallic grinding media. Fig. 1 shows the cross section of an overflow rod mill, Fig. 2 an overflow ball mill, and Fig. 3 a diaphragm (grate) discharge ball mill.

Jan 1, 1978

[ ]

Jan 1, 1907

By W. J. Reagan

All of the material described in the following paper is within the following specifications: carbon, 0.50 to 0.85 per cent; phosphorus and sulfur, 0.04 per cent max.; manganese, 0.60 to 0.85 per cent; silicon, 0.20 to 0.30 per cent. Steels with much lower carbon contents can be handled in exactly the same manner. One of the first things necessary to basic open-hearth slag control is uniformity of charge, particularly as to the silicon content and the percentage of lime charged. Our past work has shown that the silicon content of the charge is more important than the carbon content in determining the carbon at which a heat will melt. We have found that by keeping the silicon content of the charge about 0.60 to 0.65 per cent, and with a lime charge of about 7 per cent (limestone equivalent), our heats melt sufficiently high in carbon to allow a moderate feed of ore and the slag will be of low iron oxide content. In making a heat of 0.75 carbon steel we endeavor to have the heat melt at about 1.20 per cent carbon. The iron oxide content of the finishing slag depends upon the final phosphorus desired; for a given ratio of lime-silica in the slag, the lower the phosphorus desired in the final steel, the higher the iron oxide content of the finishing slag must be. By reducing the lime charge to a minimum, the heats melt faster, and by keeping the silicon content at the desired figure the heats melt with a high SiO2 slag, which has been shown in previous work to give a low iron oxide slag. In most of our work, using a 180,000-lb. charge and with basic pig containing about 1.20 per cent silicon, we use a lime charge of 8500 lb. of limestone and 2000 lb. of burnt lime. The pig charge is about 48 per cent of cold pig, and the charge contains a large percentage of works scrap. This causes a heat to melt with about 1.20 to 1.30 per cent carbon, for a heat that will finish about 0.75 per cent carbon. This gives a heat that will need a feed of about 2000 lb. of ore, and also a slag with an FeO content of about 4 to 5 per cent at melting. The additional FeO obtained from the ore addition will bring the FeO in the slag at tapping to about 6 to 7 per cent. It is necessary to carry quite a fluid slag to prevent pickup of FeO, as a too heavy slag causes FeO to build up in it, giving a finishing slag with a greater FeO than is desired. By adjusting the lime charge of a basic open-hearth heat, a very sensitive adjustment of the slag may be obtained. The figures in Table 1

Jan 1, 1935

By D. S. Kingery, D. W. Mitchell

Experience in Europe indicates that the control of dust production and dissemination by water or foam systems is not successful except during undercutting. Cybulski, Dawes, and DeBraaf-respectively Director, Mines Research Establishment "Barbara", Katowice, Poland; Principal Scientific Officer, Safety in Mines Research Establishment, Sheffield, England: and Chief, Central Mines Research Establishment, Hoensbroek, Treebeek, The Netherlands-believe that wetted dust becomes readily dispersible and abatement measures should be considered only as a temporary means for reducing the health hazard. In an effort to reduce the health hazard, calcium chloride is used on the floor of main haulageways in Dutch mines and water infusion is practiced in Germany in mines where the coal is relatively porous. With respect to wet coal dust, the Belgians, British, Dutch, French, and Russians reportedly have accepted the results of research from the Polish and American experimental mines on the effectiveness of water as an inert in arresting explosion propagation. The Polish use the two test methods proposed by the U.S. Bureau of Mines for evaluation of the adequacy of wetness of mine dust; they require that water be added to the wet dust to maintain a minimum of 50% moisture by weight if dependence is placed on water alone.

Jan 7, 1964

By B. M. Larsen

ATTEMPTING to review the fundamental aspects of segregation in steel ingots of all types in a paper of reasonable length, we encounter two difficulties: (I) the fact that a large number of different physical and chemical effects are involved, and (2) rather incomplete and confusing evidence on certain aspects of detail and mechanism in the freezing process in which the segregation effect is involved. The best solution seemed to be to link together most of the underlying factors into a simplified theoretical picture that appears to the writer to explain most of the observed data, in the hope that this will serve as a reasonably good target for discussion and criticism. Segregation effects, especially in steel ingots or castings, are often divided into " microscopic " and " macroscopic," depending on whether the variations in concentration of solutes? or dissolved elements in the iron occur as: (I) a periodic variation over the small distances between the nuclei and the surfaces of the primary grains, or (2) as a larger scale effect involving concentration gradients over distances of the order of several inches, more or less. The reason for this somewhat artificial division is, of course, that it is only the macroscopic scale effect that has much practical importance. About the only effect of practical importance that results from microscopic segregation is the banded structure often left in rolled sections, and even this is relatively harmless in most cases. However, the causes of microscopic segregation also underly the larger scale effect, so we must first consider matters such as the formation and growth of crystal nuclei, selective freezing and diffusion, and others that are fundamental to all segregation effects. UNDERCOOLING AND NUCLEI FORMATION It is probable that although the degree of undercooling is small in iron, as in metals in general, a certain amount of it takes place, and also that the number of crystal nuclei increases very rapidly with increased undercooling below the liquidus tempera¬ture. In practical terms this means that the nuclei number increases very rapidly with increased cooling or freezing rate, thus being dependent on the rate of heat flow out from the zone of crystallization. TEMPERATURE GRADIENTS AND HEAT DISSIPATION DURING FREEZING Each pound of steel evolves about 100 B.t.u. when freezing. In addition to this, the temperature gradient in the solidified portion (required to dissipate the heat as freezing progresses into the axis) necessitates a loss of heat required to cool the solid metal below its freezing range, which is equivalent to an amount of not so much less in magnitude. In a 5-ton ingot, the total would include about one million B.t.u. for freezing alone and about 0.4 to 0.5 million B.t.u. for the gradient, up to the end of the freezing period: Thus the rate of freezing depends primarily on the rate of heat dissipation. In the ordinary ingot shapes, the axial rate of growth of the solid

Jan 1, 1944

Jan 1, 1938

By G. R. Belton, Y. K. Rao

A galvanic cell, using liquid MgCl2 or MgC12-CaC12 mixtures as the electrolyte, has been used to determine activities in Mg-A1 liquid alloys between 700' and 880°C. The incovporation of a chlorine electrode in the cell also allowed measurements to be made of the standard free energy of formation of MgCl2(l). The results are shown to be in good agreement with thermo-chetrlical values from the literature, and this is taken as evidence that the small, known solubility of magnesium in iMgCl2 introduces no significant error in galcanic cell measurements. Within experimental error, the activity coefficients and relative partial molar enthalpies at 800°C are shown to be represented by the following "subregular" solution equations: logy~~ =-0.68(1 -xMgj3 log yAL =-1.02(1 - XMf + 0.68(1 - XMf H.M = -4400(1 - %)3 / cal Mg 7Ag' HZ =-6600(1 - xA1)' + 4400(1 - XMf cal SCHNEIDER and toll' have used a transpiration technique to measure the vapor pressures of magnesium over Mg-A1 alloys between 544" and 594°C. amsstad,' however, has since suggested that the extrapolation to zero flow rate, used by these authors in interpreting their apparent pressure vs flow rate data, gives unreliable results. Rogers, Tomlinson, and Richardson,3 in interpreting the results of solution equilibria between Mg-A1 alloys and liquid MgC12, also considered the measurements of Schneider and Stoll to be unreliable and preferred to derive activities for the alloys from the earlier boiling point determinations of ~eit~ebel~ and the partial molar heats recommended by Kubaschewski and ~atterall.~ These latter heats were based substantially on the early calorimetric work of Kawa-kami but, unfortunately, his work on other systems has sometimes been found to be inaccurate.7 Rogers et al., in the above-mentioned paper,3 tentatively concluded that the most likely species responsible for the limited solubility (0.3 mole pct at 800°C) of magnesium in MgC12 were Mg° (neutral) and Mg2++. Two more recent studies8,9 have supported Mg2++ as the soluble species. In the present study, activities in Mg-A1 alloys have been determined by means of a galvanic cell involving liquid MgCl2 or MgC12CaCl, mixtures as the electrolyte. Since the reactive nature of magnesium precluded simple Faraday yield experiments, a chlorine electrode was incorporated in the cell in order that the performance of the cell could be checked by measurements of the heat and free energy of formation of MgC12. This procedure was considered necessary since it has been suggested1' that the solubility of a metal in a molten salt might introduce electronic conductivity; also, previous determinations of the standard electrode potential for MgC12 differed by as much as 70 mv11-13 EXPERIMENTAL Materials. Analyses of the materials used in preparing the alloys and the electrolyte mixtures are presented in Table I. The alloys were prepared by induction melting weighed amounts of the metals in a graphite crucible held under an argon atmosphere. Pure anhydrous magnesium chloride was prepared by heating the mixture MgCl, . 6H20 +NH4C1(1:1) to 650°C, followed by melting under dry argon. The melting point of the dry MgC12 was found by differential thermal analysis to be 714.8oC, which compares well with the accepted value of 714C.14 This agreement was taken to be an indication of the high purity of the dried salt. Table I. Compositions of Materials, wt pn Impurity Mg Al MgCI2 CaCI, Ba - - 0.005 Ca - - 0.010 Cu 0.02 0.02 Fe - 0.10 0.001 0.010 Pb 0.01 - 0.001 0.005 Mn 0.15 0.001 Si - 0.10 Sr - - 0.005 MBSO* - 0.040 ARGON TUNGSTEN CHLORINE LEAD—411 11 II ALUMINA 'A I / ave GRAPHITE on irA~_ ( ^"l ROD MAGNESIUM S>ILICA~^ /, OR ALLOY-. I /A] ___________ -«^- _ ELECTROLYTE I y FRITTED DISCS Fig. l—Arrangement of chlorine and metal electrodes in electrolytic cell.

Jan 1, 1970

By James G. Crawford

Correlation Of water with its reservoir zone or formation has been one of the applications of oil-field water analysis of greatest direct value to the petroleum engineer. The water in each producing zone tends to have diagnostic characteristics by which it can be distinguished from every other water above or below that zone in that immediate vicinity. Representative analyses of oil-field waters from producing oil and gas fields in the Rocky Mountain region are included, and the diagnostic characteristics are discussed briefly. It is concluded that the generally dilute nature of Rocky Mountain oilfield waters is a result of dilution by meteoric waters, and that there is no relationship between presence or absence of commercial oil and the character of water in a structure. Introduction The study of waters associated With oil and gas began more than 50 years ago and has been well recognized by operators, engineers, and geologists for about 30 years. It appears unnecessary at this time to recite the history of oil-field water analysis; suffice to say that it has proved its worth many times to the production engineer suddenly confronted with water problems in producing oil and gas wells. Chemists and geologists have studied the possible origin of these waters and as Yet the subject is unsolved in many important phases. There are both local and regional problems connected with the explanation of concentrations and character- istics peculiar to each field, each subsurface zone and each province. Criteria useful in postulating the Occurrence of oil Or gas in One province completely fail when applied to another, and data carefully prepared and analyzed from one field may be actually misleading when applied to another. Correlation of water with its reservoir zone or formation has been one of the applications of oil-field water analysis of greatest direct value to the engineer. The concentrations and characteristics of the waters are essential to the engineers and geologists making interpretations of electric logs in this region. The behavior of water under conditions of reservoir temperature and pressure is dependent to a great degree upon its concentration and characteristics, and thus important to the reservoir engineer. With the advent of secondary recovery methods in the Rocky Mountain region the characteristics and treatment of water will become increasingly important. Premises upon which Correlation Is Based A brief review of the geochemical history of oil-field waters will suffice to present the premises upon which correlations of the waters are based. Sedimentary rocks which are now stratified were first sediments in seas, lakes and streams. These sediments were filled interstitially with connate water. With burial the sediments were compressed arid consolidated, integrated and indurated into bed rock and much of the connate water was dispelled. Following the formation of bed rock the strata were sub-

Jan 1, 1949

By Richard W. Lodge

Mr. H. R. Batcheller, of the class of 1894, Massachusetts Institute of Technology, while experimenting with chlorine gas on a certain lot of roasted concentrates, met with the following difficulties: 1. A poor extraction of the gold. 2. A very large consumption of chlorine gas. 3. Inability to precipitate all of the gold from the solutioil containing the AuC1,. 4. The bullion obtained was very base. These difficulties were the same whether the chlorine was generated from H2SO47 MnO29 and salt, or whether H2SO, and bleaching powder were used. They may be accounted for partly by the presence of some arsenic left in the roasted ore, and partly by the presence of copper in the solution containing the AuCI3. It was therefore suggested to try the effect of bromine on a similar lot of ore. The use of this element is, of course, nothing new, but in the following experiments it seemed to present many advantages over chlorine. The material worked upon consisted of some concentrates containing 2.31 ounces of gold per ton, and 34.26 per cent. of arsenic, which would correspoild to about 74.4 per cent. Of

Jan 1, 1896