Search Documents

By Milton Williams

It is generally recognized that fluid is lost from rotary drilling muds to permeable strata during normal drilling operations;1,2-3 but that this fluid is the filtrate from the mud, rather than the mud itself, has been shown by various workers.1,4,5 The presence of this filtrate in oil-bearing or gas-bearing strata is undesirable and harmful. The decreased permeability of the stratum to oil effected by the presence of water has been pointed out by several investigators,6,7 and since, in the production of the reservoir fluid, the greatest pressure drop occurs immediately adjacent to the borehole, it follows that infiltered water is particularly objectionable in this region. Again, this filtrate tends to make electrical logs less reliable, since oil in the proximity of the borehole is probably flushed out to an appreciable extent by the water.8 Observation of side wall cores may be misleading for the same reason. Drill-stem tests in low-pressure areas may be of doubtful value where no oil is recovered, unless sufficient time is allowed for production of water lost from the mud. The infiltered water may hinder drilling operations by softening shales and causing sloughing; the ['tight hole" occasioned by excessive deposition of filter cake in the hole is a common occurrence. The filter cake remaining on the face of the producing formation may itself sometimes be detrimental to production.9 In view of these implications of the importance of filtration of mud, an investigation was undertaken to determine the factors involved in the infiltration process, and to correlate these in such a manner that the values obtained in routine filter tests employing a conventional filter of the "wall-building tester" type,10 together with data on size of hole, drill pipe, and rate of mud circulation, could be used to estimate water loss and distance of penetration of the filtrate into strata. Quantitative relations of filter-cake permeability, filtrate viscosity, and rate of filtration have been developed for filtration in the simple laboratory filter.4a,11,12,13 It is obvious, however, that the conditions

Jan 1, 1940

By Douglas D. Donald

The New Jersey Zinc Co. successfully holed through a 2 1/2-mile haulage tunnel connecting its new Ivanhoe shaft with the Van Mater Shaft at Austinville, Va. This 8x 10-ft cross-section tunnel was driven from both ends and met at a point approximately a mile from one shaft and a mile and a half from the other. In order to make certain that the faces met accurately on line and grade it was necessary to refine conventional mine surveying practices. The mines that are serviced by these shafts are located in the southwestern part of Virginia approximately midway between Roanoke and Bristol at the west foot of the Blue Ridge. While the presence of lead-zinc sulfide ores has been known in this area for more than 200 years, it was in 1902 that New Jersey Zinc Co. acquired the Austinville property, which has been in constant operation since that time. About ten years ago the company undertook an extensive diamond drilling program at Ivanhoe several miles to the southwest. This program was successful in locating sufficient ore to justify the purchase of a number of the properties in this area and plans were made to develop the new orebodies. The discovery of this ore as well as substantial addi- tional reserves at Austinville resulted in a decision by the company to increase its daily milling capacity to 3000 tons, of which about 1000 tons would be supplied from the Ivanhoe mine. After careful consideration of all possible methods of transporting this volume of ore from Ivanhoe to the mill, it became evident that diesel locomotive haulage through a 2½-mile tunnel between the two mines would best suit prevailing conditions. Since the lowest operating level, known as the 1100 level, of each mine would be at approximately the same elevation, it was obvious that such a tunnel should be driven on this level. Not only would this tunnel facilitate feeding Ivanhoe ore into the underground crusher and skip loading installation at Austinville, but it would also open up a known orebody 5000 ft southwest of the Van Mater shaft. In addition it would provide a valuable diamond drilling base from which a large and a potentially favorable but untested block of ground might be explored. In order to hasten the completion of the tunnel, it was felt that it should be driven from both ends. ENGINEERING CONTROL PROCEDURES It was vital that the tunnel junction be made accurately on line and grade; thus it was felt that engineering control of an unusually high degree of reliability was required to prevent an accumulation

Jan 1, 1959

By Robert H. Carpenter

Molybdenite mineralization occurs in the hood zone of the Questa mine aplite-porphyry intrusive, one of the three sil ica-rich intrusive5 occurring along the east-west trending Red River Trench that crosses the northerly trending Sangre de Cristo Mountains in north-central New Mexico. The Trench is located immediately north of the circular Gold Hill positive block between the Red River and Cabresto Creek drainages. The aplite-porphyry bodies intruded a mid-Tertiary volcanic section consisting of lower andesites, overlain by latites and rhyolites. They occur largely in the andesites and were emplaced mainly by metasomatism rather than by sloping. Hydrothermal alteration occurs both as blanket propylitization in the volcanics and sericitization and kaolinization in the porphyries and as halo-type alteration outward from veins and shear zones resulting in strong biotization in the volcanics and sericitization and kaolinization in the aplitic rocks. Mineralization consists of: ( 1) molybdenite- quartz veinlets; (2) banded molybdenite, quartz veins frequently with biotite and potash feldspar along the walls and occasionally with minor lead, zinc, and copper sulfides and with fluorite and carbonates when again reopened; ( 3) high grade molybdenite locally along shear zones; and ( 4) molybdenite paint along joint and fracture surfaces. The mineralization was associated with faulting that resulted from numerous periods of gravity adjustment along the Trench and was controlled by the major shear systems that trend northeast, east-west and north-south to northwest. Molybdenite has been well oxidized in nearsurface exposures to ferrimolybdite and the molybdenum-bearing ferric hydroxide, akaganeite. The oxidation of the abundant pyrite within the veins and shear zones and of the alteration pyrite in the volcanics resulted in a low pH environment under which the acid molybdate ion released by oxidation was fixed either in the ferrimolybdite or the akaganeite molecule in the veins and shear zones or in the soils. Little has been lost in the runoff.

Jan 1, 1968

By J. B. Clark

In 1933, R. paris1 published a phase diagram for the entire Mg-Ca-Zn system. He reported the existence of a ternary intermetallic phase, Mg5Zn5Ca2, which formed a quasi-binary with the magnesium solid solution. Since then, no extensive work has been reported on the system. Recently however, indications of the existence of a second ternary in-termetallic phase in equilibrium with the magnesium solid solution led to a reinvestigation of the solid phase equilibria involving the magnesium solid solution. The 335°C (635°F) isothermal section was chosen for study. Metallography and powder X-ray diffraction were selected as the best mutually corroborating methods for determining the solid phase constitution. Seventy-six alloys were prepared from singly sublimed (99.95 pct) magnesium, electrolytic (99.95 pct) zinc and USP calcium. The analyses of some of the alloys are shown in Fig. 1. The alloys were melted in a graphite crucible under a chloride flu and chill cast in a split graphite mold. Dif-fusion couples (see Fig. 2) were prepared by casting molten Mg-20 wt pct Zn alloy around a cylinder of Mg-30 wt pct Ca alloy. The alloy samples and the diffusion couples were sealed under argon in Pyrex vials and annealed in a furnace capable of controlling within 1/2°C of 335°C. At the conclusion of the anneal, the alloy samples were quenched in ice water and the diffusion couples were air cooled. Procedures standard for magnesium alloys were used for metallographic examination. Powder X-ray diffraction patterns were taken on a G. E. camera with a 14.32 cm dim using nickel-filtered copper radiation. The redetermined 335°C (635°) section of the Mg-Ca-Zn phase diagram is shown in Fig. 1. TWO ternary intermetallic phases, designated w and

Jan 1, 1962

By Jed H. Mosgrove

Ventilation is the method of producing, conducting, and distributing a constant current of fresh air through mine workings and returning the impure air to the outside atmosphere. Without ventilation no operations are possible in an underground mine. Therefore it is the most important single phase of mining, one on which everything else depends. A good ventilation system, therefore, must be correctly designed, properly conducted as the workings advance, and continually checked to make sure it is functioning correctly. Good air is essential for men to comfortably and safely perform their work. It is also essential to dilute, render harmless, and sweep the mine of any explosive fumes and the gases that are released in varying degrees by all coal seams and the rock strata in which they are contained. GENERAL The body of air that is being moved through the mine, known as the ventilating current, must have a definite way to enter and leave the mine. In other words, there must be a definite intake and return. The main consideration is to get the proper amount of good quality air to the working faces where it is needed. Inasmuch as the mine is divided into sections with interconnecting corridors, known as entries, it is necessary that there be a proper means of conducting the air to the proper points. As a simple explanation of a mine, consider a long tube and think of it in terms of a mine entry ill which the air must pass. The tube must have at least two openings before air can travel through it and this is the same for coal mine entries. The problem in ventilation is to find some means that will cause the air in the tube to flow from one end to the other. The only possible way to do this is to cause greater pressure at one end of the tube than at the other. Air at the end with the greatest pressure would then, of course, flow to the en which has the least pressure. Mine

Jan 1, 1973

By D. J. McAdam

As shown in three recent papers by the author,6,7,8 in two papers by McAdam and Mebs,9,10 and in a paper by McAdam, Mebs, and Geil,11 the technical cohesive strength of a metal, in any particular state as regards mechanical treatment and heat-treatment, cannot be represented by a single stress value, but must be represented by a diagram with the principal stresses? as coordinates. Each point on the boundary of such a diagram represents a technical cohesion limit. The technical cohesive strength thus comprises an infinite number of technical cohesion limits, each representing fracture under a specific stress combination. Moreover, neither the yield strengths nor the ultimate strength can be represented completely by a single stress value, but must be represented by a diagram with the principal stresses as coordinates. All combinations of the principal stresses may be classified in three groups as illustrated by Fig. I. Fig. Ia shows three typical stress combinations with no two principal stresses equal. The magnitude of each principal stress is indicated qualitatively by the length of the arrow. Arrows pointing away from the cube indicate tensile stresses; arrows pointing toward the cube indicate compressive stresses. Typical stress combinations with two principal stresses equal are illustrated in Figs. Ib and Ic. Such stress combinations would be produced by subjecting a cylinder to combinations of uniform axial and radial stresses. The uniform radial stress may be resolved into two equal principal stresses, with the mutually perpendicular directions rotatable around the axis of the cylinder. Fig. Ib shows stress combinations with S2 equal to Sa. The greatest principal stress is in the axial direction, and the stress combination tends to cause either absolute or relative increase in length.* Fig. Ia shows stress combinations with Ss equal to Sl. The greatest principal stress is in the radial direction, and the combination tends to cause either absolute or relative decrease in length. The complete representation of either technical cohesive strength, yield strength, or ultimate strength generally requires a three-dimensional diagram. When two of the principal stresses are kept equal, however, the strength of a metal may be represented by a two-dimensional diagram with the coordinates representing the axial and radial stresses.6-11 In this paper, attention will be confined almost entirely to stress combinations with two of the prin-

Jan 1, 1944

By O. B. Harden

In working out the geological structure of a complicated district, where the problems are difficult to solve by the ordinary methods in use, a model, upon which all the geological and topographical data may be put, will be found of great value, bringing, as it does, all the facts in their proper relationship at once under the eye. In the teaching of structural geology, also, a model is of great value, since the student can thus have before him, in miniature, a representation of the rocks, as he would see them in place. Topographical models may often be useful in suits at law for damages in railroad accidents, or for trespass against mining companies, etc., in order

Jan 1, 1882

By C. A. O’Malley, F. W. Kinsey

This paper deals with an experimental study in the use of a preagglomerated burden as a means of increasing the production of sinter. The effect of a wide range of sinter burden was studied, including concentrates produced by a flotation process. Some of the important characteristics of a sinter bed are discussed along with the strength and reducibility of the sintered product. In recent years the use of sinter in blast furnaces has become increasingly important across the country—largely because of the demand for more hot iron from existing plant capacity and the increasing amount of fines in the burden materials available to the blast-furnace operator. In many instances, unfortunately, the demand for sinter has been so great that little time has been available to give the proper

Jan 1, 1960

By R. J. Lipp, I. Iwasaki, R. H. Heerema

The presence of calcium ion in iron ore pulps that are upgraded by selective desliming can result in indiscriminate flocculation of both iron oxide and siliceous gangue slimes. In order to overcome this adverse effect, deflocculation by three complexing agents, namely ethylenediaminetetzaacetate (EDTA), sodium tripolyphosphate (STPP), and sodium hexametaphosphate (SHMP), was investigated. The precipitates and complexes of these agents with calcium ion were characterized by potentiometric and conductometric titrations, and the surface properties of quartz and goethite were studied in the presence of calcium ion and of the complexing agents by means of streaming potential measurements and flotation tests. The results were then correlated with selective flocculation tests on an artificial mixture of quartz and goethite. EDTA markedly improved the selectivity of flocculation when added in near stoichiometric amounts, whereas STPP was less effective and SHMP was totally ineffective due to strong, indiscriminate dispersion. Remanent calcium polyphosphates on the goethite surface interfered with the adsorption of starch flocculant.

Jan 1, 1983

By F. A. Seward

A1though the expanding Eltran1 configuration has been used in induced polarization exploration for several years, there has been little application of this method to straight resistivity problems. A comparison of results of resistivity exploration by this technique versus those obtained from Wenner configuration surveys reveals a number of advantages in interpretative resolution as well as in field operation. The application of electrical resistivity to ground-water exploration is well known.= In the past a major portion of this work has been accomplished by use of one or more variations of a technique employing the Wenner3 electrode configuration. With the introduction of the frequency domain technique of induced polarization measurements, used primarily in the exploration for disseminated sulfide deposits, there arose the need for an electrode configuration by which potentials could be measured externally to the current electrode spread in order to minimize coupling between current sending and potential receiving circuits. It was also deemed desirable that the configuration would provide information laterally along profile as well as with depth. To reach these objectives the expanding dipole-dipole configuration (which probably first was used in the electrical transient method of exploration and from which the name 'Eltran' was derived) has been adapted to induced polarization exploration. The author has successfully applied the same techniques

Jan 1, 1963

There are two types of shovels currently used primarily as mining tools-the stripping shovel and the quarry-mine (Q-M) shovel. The two types have basically the same features, the main difference being in size. The stripping units are giant four-crawler shovels that operate by placing overburden alongside in a mined-out area. The Q-M units, on the other hand, are two-crawler shovels that usually load into trucks or trains. Powering Systems A typical stripping or Q-M shovel is fully electric, receiving power through a trailing cable that is connected to a large motor-generator set with multiple generators. In the full Ward-Leonard system, each generator furnishes d-c power to separate motors which drive the mechanisms for the principal motions of the shovel-hoist, crowd and swing.

Jan 10, 1967

By C. M. Moncrief

A bentonite-clay drilling mud when treated with tetrasodium pyroarsenate underwent substantially the same reduction in viscosity and water loss as when treated with the complex phosphates. The complex arsenate showed a slightly higher reversion after heating; the other arsenates showed poor viscosity-reducing properties. Introduction During the past 10 years the chemical control of drilling mud has become of major importance in affecting the successful drilling and working over of wells. The desired properties of drilling mud have been well established, and in obtaining these characteristics there has developed a large market for viscosity-reducing chemicals. Viscosity reduction produced by humic acid, tannic acid, sodium silicate, sodium tannate, Calgon, and the complex phosphates has been described by Loomis, Ford, and Fidiam.l The effects Of treatment with complex phosphates and ammonium PolyPhosPhates on the rheological properties of muds were investigated by Fancher2 and the alkali vanadates have been described by Williams.3 Laboratory Investigations It is the purpose of this paper to point out the effects of arsenates in controlling the viscosity and gelling characteristics of a drilling mud. Viscosities and gel strengths were measured at room temperatures with a Stormer viscosimeter calibrated in centipoises and operated at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester at a pressure of I00 lb. per sq. in. for 30 min. The hydrogen-ion concentration was measured with a glass electrode. The bentonite-clay suspensions were prepared in the laboratory and allowed to age several days before testing. Members of the Arsenic Group in the periodic Table include arsenic, antimony and bismuth, but this investigation was limited to arsenic. Phosphorus also occurs in Group V of the Periodic system and phosphorus and arsenic form many closely related compounds such as pH3 and AsH3, P2O5 and As2O5, H3PO4 and H3AS04 Samples of tetrasodium pyroarsenate were prepared by fusing c.p. disodium arsenate (Na2HA5O4.7H2O). According to Friend,' this re-forms the ortho-arsenate on dissolution in water. Sodium trihydrodiorthoarsenate was prepared as described by Mellor,5 from arsenic pen-toxide as follows: As2O5 + 3H20 -> 2H3AsO4 2H3AS04 + 3NaOH Na3H3(AsO4)2 .3H20 Sodium dihydrogen orthoarsenateWaHz-As04) was obtained by fusing together equivalent quantities of arsenious Oxide and sodium nitrate, dissolving the residue in water and allowing it to crystallize.

Jan 1, 1946

By F. V. Greene

This paper is based on my experience in the use of asphalt, for paving and other purposes, during the last ten years, part of the

Jan 1, 1889

By J. H. Klepinger, C. W. Goodale

I. Introduction....................567 II. Character oF the OrE................568 III. Old FluE System..................572 IV. Tests on Old FLUE System..............575 1. Aspiration Tests................. 575 2. Tests with Steel Settling Chamber........... 575 3. Test with Experimental Brick Flue........... 583 4. Testa on Blast Furnace Geses............. 591 V. Design of New FluE System.............. 597 VI. Main Dust Chamber................. 605 VII. Some DetailS of Construction ............. 609 VIII. THE Chimney.................... 616 IX. Operation of New FluE System............. 624 X. Temperatures and DraFTS............... 630 XI. Velocities and Volumes................ 632 XII. TeStS on the New FluE System............. 637 XIII. Conclusion..................... 643 I. Introduction. In the summer of 1909 the Boston & Montana reduction department of the Anaconda Copper Mining Co. completed a new flue system, at a cost of about $1,100,000, and as this includes the largest and highest chimney in the world, and some new features of flue construction, a description will be of interest. At the Spokane meeting of the Institute in September, 1909, a brief mention was made of this flue system, in discussing Mr. Brunton's presidential paper on the Progress of Metallurgy in the West, and a promise was given that when a long enough time had elapsed, so that operating results could be given, a paper would be offered. The smelting plant includes blast furnaces, MacDougall roasters, gas-fired reverberatories, and converters.

Jan 1, 1914

By James R. Cost

The increasing emphasis upon the use of refractory metals has resulted in a closer look at some of the properties of these materials. In the course of a study of the Nb-N system it became necessary to re-examine one such property, the spectral emissivity, e. Experiments were performed in order to determine e for solid niobium as a function of both temperature and nitrogen content. The results of these experiments, which indicate a small but significant correction to the spectral emissivity of pure niobium, are reported herein. In addition, data on the total emissivity, et, of niobium and the spectral emissivity of the nitride Nb2N are given. To this author's knowledge, neither of these emissivities are as yet reported in the literature. Previous studies of the spectral emissivity of niobium have been few. In 1915, Burgess and Waltenburgl obtained a value of 0.49. Whitney? in 1935, used a Mendenhall V to obtain the commonly accepted value of 0.374. A recent investigation of sintering of niobium graphically reported a value of about 0.36= using a solid block of the metal with a blackbody hole drilled into it. In the present experiment a method similar to that of Worthing4 was used. An 8-in. long and 3/16 in. diam hollow tube was formed from smooth surfaced 0.0013-

Jan 1, 1962

By G. E. Erdman

Gouverneur Talc produces a dry mineral filler from the tremolite talc rocks located near Gouverneur, New York. The raw material for this rock powder is a silicate rock and dust is controlled by water sprays whenever it becomes a problem underground. In the milling operation, there are some nine baghouse-type dust collectors which are utilized for the control of dust created in the crushing and grinding process. These collectors have been installed over a period of years since 1947 and are assigned to specific areas where the particle sizing of the dust can be returned to the plant circuit or product involved at the point of collection. It has been found very advantageous to mount most of these collectors on the top of the mill building and packhouses where the return of the dust can be accomplished by a gravity feed. In the years of effort involved in efficient control of dust generated in the plant, many things have been learned in the construction of ducts for control valves. The company has found useful such things as grasshopper legs for interconnecting silos with similar products, the elimination of fiat dust ducts, cleaning cyclones for coarse dust or heavy loadings, refractory linings for cyclones and certain duct areas, and the avoidance of square intersections when diverting or combining ducts. Operating cost records indicate that collectors handling the finest dust have the least expense. Operating costs on high-temperature dusts generally run higher than other types of material collected. Experience further indicates that the multiple cyclone-type collectors can provide a low cost and efficient way of removing hot dusts from process air streams before the introduction of the material into a baghouse. High moisture conditions and cold northern climates have been found to combine and create conditions under which baghouses can not efficiently function as dust collectors. Gouverneur Talc feels that its several dust collection systems have been a considerable maintenance expense but well worth the cost when it came to safeguarding the employees' health and preventing air pollution.

Jan 1, 1974

By Ronald A. Murdock

INTRODUCTION Exxon's Highland Uranium Operations in eastern Wyoming consists of an open pit, an underground mine and a mill complex. The geology of the deposit is reviewed in this paper, and an overview of the mining operations at both the surface and underground mines is presented. Topics discussed include geology, stripping of overburden and mining of ore in the open pit, and underground development and stoping methods. GEOLOGY The Highland uranium deposit was discovered in 1968 by Exxon Minerals Company, U.S.A., in Converse County, Wyoming, 35 miles north of Douglas. The mine is located at an elevation of about 5,200 ft in a high-plains, sagebrush-covered prairie typical of eastern Wyoming. The deposit is near the southern edge of the Powder River Basin in the Paleocene Fort Union Formation. The Fort Union Formation consists of 1,900 to 3,200 ft of sandstone, siltstone, mudstone, claystone and coal beds. Siltstone, mudstone and claystone are collectively referred to as "shale" at Highland. There are many alternating layers of shale and sandstone in the Fort Union Formation; but in the Highland area, there are only three principal sandstones, known as the Highland Sand Group, which host the uranium. The combined sand thickness is about 150 ft.

Jan 1, 1983

By Oswald J. Heinrich

(Read at the Amenia Meeting, October, 1877.) THE deposit of rock salt along the shores of Lake Huron, in Canada, has been brought before the public during the last six months, in consequence of the developments made by the diamond drill at Goderich. It is likely to be of more than common interest in the future, since now actual operations have been commenced to exploit the deposit and work it by regular mining. The methods of mining rock salt being but little known in this country, it may be of interest to make a few general remarks in regard to them before entering, upon the description of this new mining enterprise. According to the conditions under which salt is found in nature, various methods have been resorted to, in course of time, to make it available for the human race. They consist in : A. Natural or solar evaporation. B. Artificial evaporation, either exclusively or in connection with the former. C. Mining the rock salt in its natural state, and converting it to a marketable product, if need be, by simply pulverizing it. Without going into the details of the various methods of making salt available in an economical point of view, dependent on its degree of purity, or on various local influences, we cannot refrain from. alluding to the general principles which influence the mining and manufacturing of salt in countries where they have been carried on for hundreds of years. ECONOMICAL CONDITIONS FOR SUCCESS. Salt being one of the articles of prime necessity, and one universally distributed throughout nature, it must always be sold at a comparatively low price. It would even be quoted in the market at prices far below those now ruling, if it were not for the high duties generally imposed upon it, for purposes of state revenues. But looking closer into the subject, it will be found that this duty is probably one of the least oppressive, although in some countries it exceeds sixfold the cost of profitable production. To produce the article at the lowest possible cost requires, therefore, a

Jan 1, 1878

By J. T. Shimmin

THE past twenty-five years has been a period of unparalleled improvement in all lines of mining and metallurgical equipment, but probably none has undergone greater refinement and development than the vacuum filter. Beginning a quarter of a century ago, there has been steady advancement in the art of vacu-um filtration until today its use has become virtually standard practice for dewatering throughout the entire metallurgical industry as well as in important parts of the chemical and industrial processing fields. The credit for the first successful application of vacuum filtration 'at the Consolidated Mercury mines in Utah in 1902 undoubtedly belongs to George Moore. There, it is said, his filter reduced the loss of gold in the slime and sand from $1.25 to 40c. per ton. Successful applications were subsequently made by Mr. Moore at the Liberty Bell mines, Telluride, Colo., the Lundberg, Dorr &Wilson mill at Terry, S. D., and elsewhere. E. L. Oliver is generally credited with, having done the most to work out the necessary continuity of op-eration exemplified in the well-known continuous vacu-um filter which bears his name. Others made improve-ments also, but in my opinion all the new ideas advanced in recent years are modifications of the fundamental principles originated by the two pioneers, Moore and Oliver. Considerable interest has been shown recently in the new type of continuous internal-type vacuum filter which is associated with my own name1. In response to frequent inquiries regarding it and the steps which led up to its invention, I am giving herewith a brief account of the early history of this development and some of the more important installations which have been made during the last year or so. A. M. Nicholas (now deceased), an Australian engi-neer, conceived the idea, several years ago, of manu-facturing a continuous vacuum filter with the filter medium applied upon the inside of the drum, as con-trasted with existing drum filters in which the medium is applied externally. Nicholas recognized that a ma-chine of this type would be simpler than one with a tank and would overcome some of the difficulties en-countered with tank filters on certain classes of pulps, and he appreciated the value of having filtration take place in the same direction as the gravitational settle-ment of the solid particles in the pulp, the pulp being retained within the drum instead of being held against the outside surface. The ease of starting up after a shut down was likewise realized by Nicholas. It was tried in the United States, but was not entirely success-ful primarily due to mechanical defects.

Jan 5, 1928

By G. Rinelli, A. M. Marabini

Flotation of rutile with N-benzoyl-N-phenyl-hydroxyhmine (N-BPHA) has been investkated. Initially, floatability tests were performed in a Hallimond tube. The results indicated that rutile was floatable at pH 2-4 with N-BPHA concentration between 2 x 10-3 mol/L and 2 x 10-2 mol/L. Selectivity against hematite was recognized when operating at pH values below 2. Following the hypothesis of the formation of a surface chelate between N-BPHA and titanium ion, this compound was precipitated from a solution of Ti (SO4)2 to which N-BPHA was added. I. R. spectrometry of the rutile before and after treatment with N-BPHA solution confirmed the presence of this compound on the rutile surface. Adsorption isotherm and kinetics were determined by analyzing N-BPHA in solution with an U. V. technique. A hypothesis on the way N-BPHA is adsorbed on rutile is presented.

Jan 1, 1984