Search Documents

By Luis E. Vallejo

Experimental and theoretical analyses are presented to study the mechanics of growth and interaction for three inclined left-stepping, three inclined right-stepping and two inclined non-stepping cracks in a brittle material subjected to uniaxial compression. It was found that the non-stepping cracks did not interact and they propagated individually in a direction parallel to the uniaxial compressive stress. The propagating cracks formed in regions where tensile stresses developed. The left-stepping cracks interacted and formed branching cracks as a result of failure in tension of the material between them. Also, they propagated from their tips in a direction parallel to the uniaxial compressive stress. The right stepping cracks did not interact, but extended themselves from their tips following a direction parallel to the uniaxial compressive stress. The extended cracks formed in areas of compressive stresses.

Jan 1, 1984

By F. E. Werner, B. L. Averbach, Morris Cohen

THAT bainite formed near the M, temperature bears a striking r esemblance to martensite tempered at the same temperature has been shown by the electron microscope.' By means of electron diffraction,' it has been established that carbide and cementite are present in bainite formed at 500°F (260°C); these carbides are also found in martensite tempered at 500°F (260°C).' The investigation reported here is concerned with an X-ray study of the matrix phases in lower bainite and tempered martensite. These phases have turned out to be dissimilar in structure; the matrix of bainite is body-centered-cubic while that of tempered martensite is body-centered-tetragonal. A vacuum-melted Fe-C alloy containing 1.43 pct C was studied. Specimens of 16 in. diam were sealed in evacuated silica tubing and austenitized at 2300°F (1260°C) for 24 hr. One specimen was quenched into a salt bath at 410°+7 °F (210°+4°C), held for 16 hr, and cooled to room temperature. The structure consisted of about 90 to 95 pct bainite, the re: mainder being martensite and retained austenite. A second specimen was quenched from the austen-itizing temperature into iced brine and then into liquid nitrogen. It consisted of about 90 pct martensite and 10 pct retained austenite. The latter specimen was tempered for 10 hr at 410°+2°F (210°+1°C). The specimens were then fractured along prior austenite grain boundaries (grain size about 2 mm diam) by light tapping with a hammer. Single aus-tenite grains, mostly transformed, were etched to about 0.5 mm diam and mounted in a Unicam single crystal goniometer, which allowed both rotation and oscillation of the sample. Lattice parameters were measured by the technique of Kurdjumov and Lyssak. This method takes advantage of the fact that martensite and lower bainite are related to austenite by the Kurdjumov-sachs orientation relationships Thus, the (002) and the (200) (020) reflections can be recorded separately, permitting the c and a parameters to be determined without interference from overlapping reflections. According to these findings, the matrix phase in bainite is body-centered-cubic and, within experimental error, has the same lattice parameter as ferrite (2.866A). On the other hand, martensite, tempered as above, retains some tetragonality, with a c/a ratio of 1.005t0.002. Most workers in the past have assumed that bainite is generated from austenite as a supersaturated phase, but the nature of this product has not been established. The question arises as to whether bainite initially has a tetragonal structure and then tempers to cubic, or if it forms directly as a cubic structure. If it forms with a tetragonal lattice, it might well be expected to temper to the cubic phase at about the same rate as tetragonal martensite. The martensitic specimen used here was given approximately the same tempering exposure, 10 hr at 410°F, as suffered by the greater part of the bainite during the isothermal transformation. About 50 pct bainite was formed in 6 hr at 410°F. On tempering at this temperature, martensite reduces its tetragonality within a few minutes to a value corresponding to 0.30 pct C.' Further decomposition proceeds slowly, and after 10 hr the c/a ratio is still appreciable, i.e., 1.005. Thus, even if the bainite were to form as a tetragonal phase with a tetragonality corresponding to only 0.30 pct C, which might be assumed to coexist with e carbide, it would not be expected to become cubic in this time. It seems very likely, therefore, that bainite forms irom austenite as a body-centered-cubic phase and does not pass through a tetragonal transition. The carbon content of the cubic phase has not been determined, but it could easily be as high as 0.1 pct, within the experimental uncertainty of the lattice-parameter measurements. It has been postulated that retained austenite decomposes on tempering into the same product as martensite tempered at the same temperature. There is now considerable doubt on this point. The isothermal transformation product of both primary and retained austenite at the temperature in question here is bainite," and the present findings show that bainite and tempered martensite do not have the same matrix. Acknowledgments The authors would like to acknowledge the financial support of the Instrumentation Laboratory, Massachusetts Institute of Technology, and the United States Air Force.

Jan 1, 1957

By T. W. Lippert

In these opening remarks, I will endeavor to give a background of continuous casting of metals. Only passing attention will be given to the different processes to be described by the authors whose papers are on the program, as they are far more familiar than I am with their subject matter. Suffice to say that over the past several years the brass, copper, aluminum and magnesium industries have shifted practically completely from conventional static molds to continuous casting machines. The Aluminum Company of America alone has more than 60 continuous machines in operation. The product as continuously cast is superior metallurgically, less scrap loss is involved, costs are generally lower, and the equipment requires little floor space. A continuous machine, operating as it does with deadly constancy, is a ravenous consumer of molten metal, and in most plants one or two machines are well able to handle large banks of melting and refining furnaces. In steel, interest in continuous casting is today more serious than ever before in history, and there is every reason to believe that continuous machines may secure a minor place in the ferrous industry, particularly for tool and alloy analyses. In the past, steel has been commercially cast continuously, and today many tons of steel are being turned out in this manner. It has been said that the cradle of every science is surrounded by dead theorists— and certainly there are innumerable examples of this in the metals industries. An excellent illustration, for instance, is the continuous rolling of metal, a tantalizing objective that for decades on end exhausted . the efforts of a long line of famous, infamous and unknown inventors. Finally, in 1922, John B. Tytus, of the American Rolling Mill Co., brought forth what now seems such an obviously simple scheme— a concave roll face, each stand of progressivcly less concavity. And out of this one change in design sprang today's wide continuous mill rolling steel sheet Ioo in. wide at 2000 ft. per minute. Another excellent example is the con- . tinuous casting of liquid metal into an intermediate form, preferably one requiring little subsequent breakdown. First, the casting of liquid metal alone was fascinating enough. Then someone passed the cast metal directly into a rolling mill, and shortly thereafter this continuously rolled strip was passed directly into a stamping machine. This leitmotiv of a continuous flow of metal from the liquid phase to a consumer end product, fast and inexpensive, and all housed within a small space, was enough to drive some 200 or so inventors into frenzy over the past hundred years. All the ideas, however, like mayflies, had only their brief afternoon of existence. They were born and they died on paper, as constant exemplification of that great void that always exists between mental production and commercial production.

Jan 1, 1945

This is a brief account of the history of unit operation in the Salt Creek field, Wyoming, from the time of the agreement to prorate production in March, 1921, to the present. An attempt has been made to evaluate the savings in development and production costs resulting from the unit plans adopted. Summarized, these savings have amounted to $11,650,000. No effort has been made to estimate any increase in ultimate recovery, for it is believed that unit operation can be justified on saving in development and production costs alone. It would require nearly 20,000,000 barrels of additional oil to be produced in order to return the amount saved by not drilling unnecessary wells. Four horizons are affected by unit or near-unit programs, as follows: The principal operator is under contract with six companies to operate 10,400 acres. This includes all of the productive area of the First Wall

Jan 1, 1930

By Joseph Hartshorne

This plant is situated in the borough of Pottstown, on the banks of the Schuylkill river, between the Philadelphia and Reading Railroad and the Schuylkill Division of the Pennsylvania Railroad, on a plot of about 125 acres, most of which is reserved for future extensions. About 45 acres are to be used for houses, 40 of which have already been built. The accompanying plan will give a clear idea of the general arrangement of the works. Beginning at the lower or eastern end, the first building is the basic-cinder grinding-plant. At present, it consists of a 2000 mm. Jenisch ball-mill (Kugelfallmühle) similar to those used so extensively for grinding basic cinder in Europe. It was built by Herman LÖhnert, of Bromberg. The mill is very simple in design, and efficient in execution. About 13 horse-power is required to run it, and the average output is 20,000 pounds in 10 hours. The best work we have done is 29,000 pounds in 10 hours, with perfectly dry cinder. From 95 to 98 per cent. of the product will pass through a sieve with 100 meshes to the inch, while from 70 to 75 per cent. will pass through a 150-mesh sieve. The mill has been in service since last March, part of the time on double-turn, and the renewals and repairs have been very slight. The product of the plant is sold as a fertilizer. It runs from 18 to 24 per cent. in phosphoric acid, about 14 of which is reverted. The merits of this fertilizer were explained by Mr. W. H. Morris, at the Baltimore meeting of February, 1892 (Trans., xxi., 232), and by Mr. W. B. Phillips, at the Birmingham meeting of 1888 (Trans., xvii., 84). The results obtained by its use in Europe, where over 600,000 tons were used last year, are well known. Near the cinder-grinding plant will be situated the new machineshop, which is now being erected. The next buildings contain the brick-making plant and ovens.

Jan 1, 1893

By H. Krueger, H. N. Hersh

USE of autoradiography in diffusion studies offers the advantage that no repeated sectioning is necessary and that the analyses are performed in a simple manner over the continuous range of penetration depths. As part of a program of solid-state physics, it was desired to develop the autoradio-graphic method' quantitatively for use in diffusion studies. Results are reported here for the self-diffusion of silver. Silver was chosen because the existing data are good enough to evaluate the technique." The silver used in this investigation was obtained in the form of ¼ in. diam rods of polycrystalline material, 99.99 pct purity. The radioactive silver, Ag110 (ß, y), was obtained as the nitrate and converted to the chloride for use in a standard cyanide plating bath. The diffusion specimens were 1/2 in. lengths of the rod. They were mounted in bake-lite and the exposed circular face carefully ground and polished. Prior to electrodepositing radioactive

Jan 1, 1956

By M. I. Jacobson, A. S. Yue, A. E. Vidoz, F. W. Crossman

An equation governing the concept of constitutional supercooling under the combined effect of concentration and temperature gradients was used to produce platelike Al-CuAl2 eutectic composites for mechanical properties studies. Compression specimens were prepared from a single-colony Al-CuA12 eutectic composite ingot, 2 in. in diam and 12 in. long. The specirrzens were cut such that the platelets were oriented parallel, 45 deg, and perpendicular to the compression direction. Since the ingot was of eutectic composition, The aluminum-rich matrix could dissolve 5. 7 wt pct Cu in solid solution, and therefore could be strengthened by precipitation hardening. Specimens were tested at room temperature and elevated temperatures in the unidirectionally solidified, solution-treated, and solution-treated plus aged conditions. The results were compared with those for the conventionally cast and extruded specimens. For the controlled material, the highest strengths were obtained with platelets oriented parallel to the compression axis. In the unidirectionally solidified condition, 0.2 pct offset yield strength was 32,000 psi; however, this was increased to 59,000 psi by solution treatment, and further increased to 90,500 psi by solution treatment and aging. The attainment of high compressive strengths in the Al-CuAl2 eutectic composites was interpreted in terms of the buckling of elastic CuAl2 platelets in the plastically deformed a aluminum matrix. SINCE the discovery of high-strength whiskers,' scientists and engineers have made significant progress toward incorporating these whiskers into metallic matrices, forming composites for basic studies and structural application. The general procedure is to produce the whiskers first and then to bind them together with a ductile matrix. The production of whisker-reinforced composites requires tedious handling techniques,, particularly when it is desired to align the whiskers unidirectionally. Furthermore, the interfacial bond between the whisker and the matrix is frequently poor3 so that the resulting composite has strengths lower than expected. These disadvantages are generally true for any metallic composite produced by physically mixing the components. It is possible to eliminate these shortcomings by growing whiskers directly in the matrix material by eutectic solidification.4-8 In eutectic solidification, the matrix phase and a whisker phase are grown approximately simultaneously from a liquid of the same overall composition at the eutectic temperature. If the solidification process is controlled by varying the freezing rate, the temperature gradient, and the impurity content, platelike or filamentlike whiskers are produced parallel to the growth direction. The morphology of the grown-in reinforcement, i.e.. plates or rods, generally depends on the volume fraction9 of the dispersed phase present in the eutectic mixture. Since the unidirectional eutectic solidification is a one-step process, i.e., the liquid-solid transformation process, an excellent interfacial bond between the matrix and whisker is obtained. An additional advantage is that no special handling technique for whiskers is needed. In recent years, many investigators10-13 have studied the effects of growth variables on the micromorpholo-gies of binary eutectic alloys produced by controlled solidification. The study of their mechanical properties was initiated by Kraft and coworkers14-16 who found that the strength of cast A1-CuA12 eutectic alloy can be increased threefold by unidirectional solidification. In the A1-AL3Ni system, a strength of 50,000 lb per sq in, was reported for the unidirectionally solidified eutectic alloy, a value five times higher than for conventionally cast material. Thus, the unidirectionally solidified eutectics can be used as fiber-reinforced composite materials. In this paper, we shall first use an equation17 as a guide for the production of eutectic composites in general and the Al-33 wt pct Cu eutectic in particular. Experimental data supporting the theoretical prediction are given. Second, the compressive properties of the grown A1-33 wt pct Cu eutectic were thoroughly investigated in terms of platelet orientations, thermo-mechanical treatment, and temperature. The experimental data are interpreted in terms of a buckling model of fibers in elastic fiber-plastic matrix metallic composites. EXPERIMENTAL PROCEDURE Crystal Growth. The following experimental procedure was adopted for the production of controlled microstructures in the A1-33 wt pct Cu eutectic alloy. The controlled solidification was accomplished with a movable resistance-wound radiation furnace. Fig. 1 is a schematic drawing of the solidification apparatus. A water-cooled chiller was placed into a degassed high-purity graphite crucible containing the charge. Rubber stoppers wrapped with aluminum foil were used to seal both ends of the quartz tube through which a dried argon atmosphere was passed under a slight positive pressure. At both ends of the quartz tube, radiation shields were used to minimize heat loss. The quartz tube was held in place by two steel clamps and the furnace was drawn vertically by means of a steel cable against the steel truss which permits the furnace to move without touching the tube. The drive mechanism consisted of two pulleys, a counter weight.

Jan 1, 1969

By George E. Aiken

Modern high speed bucket wheel excavators (BWEs) can dig materials which power shovels can't handle without blasting. Yet these machines are not used in any large, open pit ore mines in the United States. American mining has been slow to use the wheel's special capabilities of high production volume at low cost, due perhaps to a traditional familiarity with shovels and draglines and/or the lack of data of BWE operation, design and cost. Of course, shovels and draglines can not be replaced by BWEs in all cases, but under suitable conditions bucket wheels can out-perform other conventional excavators and simultaneously permit significant operating savings. The latter aspect will become increasingly important to American mining men because as more low to medium grade orebodies are found in regions of thick overburden, better and cheaper ways of uncovering them must be developed. Typical of such areas are the thick alluvial fans of the Southwest and the glacial drift areas in northern regions. Much of this material would handle well with a wheel excavator without blasting, although ripping might be necessary in some cases.

Jan 1, 1966

By Norbert R. Morgenstern

INTRODUCTION An understanding of the role of water in controlling the stability of rock masses is central for a rational approach to the subject. The presence of water can hinder mining opera- tions in two ways: 1. excessive discharge 2. excessive pressure It should be noted that if the rock mass is very tight, excessive pressures can exist without large discharges. Alternatively, if abundant water is available and the rock mass is open, then substantial discharges can occur under quite small pressures. The problems associated with excessive discharge are usually well understood by the mining engineer. Vehicle mobility is inhibited, some areas are flooded and hence become inaccessible; at best, a costly nuisance exists. The methods of solving these problems are also well-known to mining engineers. They generally involve tapping the source of the excessive discharge and channeling it away in such a manner that any hindrance to the mining operation is minimized. The effects of water pressure on the stability of rock masses are less obvious and the following will be devoted solely to this aspect of the problem. The manner in which water pressures enter into the consideration of stability is made clear by an understanding of the concept of effective stress. THE CONCEPT OF EFFECTIVE STRESS The simplest mechanical model for the problem of rock slope stability consists of a rough, rigid block sliding down an inclined plane under the influence of gravity. This is illustrated in [Fig. 1]. The down-slope component of the weight of the block tends to produce movement which is resisted by the shearing force generated by friction along the base of the block. The shear stress per unit area inducing movement is

Jan 1, 1971

By Charles Trotter

AN instrument has recently been developed for determining the inclination and azimuthal direction of boreholes. This instrument is known as the Tro-Pari Instrument and is the invention of C. Trotter and G. Pajari of Sudbury, Ontario. DESCRIPTION The instrument is characterized by a unit mounted in gimbals and provided with a clockwork mechanism to clamp a compass to indicate azimuthal direction and simultaneously to clamp the unit in its plumb position to indicate inclination (Fig I). By means of a timing ring suitably calibrated in 5-min divisions, the unit may be set to lock after a lapse of time sufficient to allow the placing of the instrument at the desired point in the drill hole where readings are to be taken. The maximum time lapse obtainable with the instrument designed for use in EX or AX size holes is 1 hr 30 min which is considered to be ample time to lower to the greatest depths that may be drilled with this size of equipment. Larger sizes could be developed for larger diameter holes such as BX and NX sizes or the larger oil-well sizes and a correspondingly greater time lapse could be provided for. Up to the present time only the EX-AX size has been built. OPERATION Assuming a borehole is to be surveyed at 1000-ft depth and assuming it will take 30 min to lower the instrument to this depth, the timing ring is rotated through seven divisions which represent a time lapse of 35 min (5-min leeway) and is then returned to its zero position. This operation imparts energy to a spring which drives the clockwork mechanism. Simultaneously the compass needle is freed to swing to its magnetic north-south position and the encased mechanism is freed to hang plumb within a semicircular portion of the frame which is graduated in degrees after the fashion of a protractor. This semicircular protractor portion has a V-shaped notch at each degree division of its inner periphery. The instrument, now in its free position, is inserted in a bronze container made to suit the size of hole to be surveyed (Fig 2). Soft rubber washers are provided within the container to prevent undue shock. The container is connected to the drill rods with three 5-ft lengths of brass or aluminum alloy rods separating it from the steel rods in order to prevent distortion of the magnetic field. The assembly is then lowered to the desired point where readings are to be taken and is allowed to remain at rest until a period of time has elapsed slightly in excess of the time for which the timing ring was set. In the example cited above, when the 35 min has elapsed the compass needle is locked in its north-south position and the protractor locking pin is extruded and locks in the V notch opposite its plumb position. The device may now be removed from the borehole and it will remain in this locked position in spite of jarring or shak-

Jan 1, 1947

By George R. Elliott

Methods are presented for measuring and comparing "degree" of water drive, and for observing the control that rate of withdrawal exerts over decline of reservoir pressure. Degree of water drive is studied from pressure-production curves of 10 reservoirs; the method used to present these comparatively is to convert cumulative oil production from barrels to percentage of ultimate. Degree of water drive is also represented by a "water-encroachment factor," representing barrels of water influx per pound-month per acre-foot of oil reservoir. Pressure-production curves for the water-drive reservoirs after a period of declining pressure show a diminishing angle of slope, in some cases to the point where pressure ceases to decline or where it even increases; the shapes of these curves are in marked contrast to the dissolved-gas type of curve, which shows a general trend toward zero pressure at ultimate oil recovery. Yearly rate of oil production in percentage of ultimate oil recovery is correlated with pressure decline. The correct rate of production of oil with its associated gas and water sustains pressure in reservoirs having a high water-encroachment factor. For reservoirs having a low water-encroachment factor, it is necessary to inject the produced water and even inject large volumes of water from an outside source. The discussion of the actual reservoirs is preceded by a general review and is followed by a substantial bibliography. It is now generally accepted that water drive is capable of yielding 60 to 80 per cent of the original oil in place in most reservoirs, as compared with 20 to 40 per cent for dissolved-gas drive. There is no need to question the importance of controlling a reservoir in order to take advantage of such an efficient mechanism. What is a water-drive reservoir? Oil reservoirs usually combine two or more of the four basic mechanisms: dissolved-gas drive, gas-cap drive, water drive, gravity drainage. A water-drive reservoir is one in which water advances to take the place of the oil and gas produced. When the oil withdrawal rate is sufficiently low, the water will tend to maintain pressure. The maximum effectiveness is attained when the water follows the oil withdrawal so closely that little or no decline in pressure occurs. Oil in its underground reservoir is associated with water. This water is significant in the production of the oil according to the source of supply and the permeability of the surrounding formation. As oil is produced and the pressure is lowered, water can move in to replace the oil. With adequate supply and sufficient permeability, actual movement takes place on an extensive scale. The first movement of water takes place by expansion of the water and its associated fluids. While this expansion is of little importance in some fields, in others it is sufficient to supply all of the energy required for the production of oil. When a pressure differential has been established

Jan 1, 1946

EXECUTIVE COMMITTEES OF LOCAL SECTIONS New York LOUIS D. HUNTOON, Chairman. ARTHUR S. DWIGHT, Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. E. MALTBY SHIPP. Treasurer. GEORGE F. KUNZ, W. De L. BENEDICT. Boston ROBERT H. RICHARDS, Chairman. ALBERT SAUVEUR, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. TIMOTHY W. SPRAGUE. HENRY A. WENTWORTH. Columbia F. A. THOMSON, Chairman. GEORGE W. RODDEWIG, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer. P. O. Drawer 2154, Spokane, Wash. R. S. McCAFFERY. S. H. RICHARDSON.

Jan 5, 1914

By Shiou-Chuan Sun

THERE are several postulations for the mechanism of slime-coating. Ince1 proposed the electrostatic hypothesis, del Giudice2 suggested the chemical theory; Bankoff3 reported that slime-coating is inhibited whenever the surfaces of the slime particles are ionized sufficiently for Brownian movement to occur, and is facilitated when they are not. These postulations were examined by experiments involving the Burton tube, the cataphoretic cell, and slime-coating. The techniques involved will be described elsewhere in this paper. The electrostatic hypothesis, supported by migration experiments in a Burton tube, was abandoned by del Giudice.2 Experiments of mineral migration in a Burton tube, after the idea of Ince with modification, indicated that this apparatus was inefficient for accurate observation. A cataphoretic cell was constructed. The experimental data, as shown in this paper, enable the correlation and advancing of this hypothesis. Del Giudice's chemical hypothesis considered that slime particles are attached to the galena surfaces by a cement formed as the result of a metathetical reaction between the sulphide and the slime particles. Applying this hypothesis, the calcite slime particles were cemented to the galena surface by the formation of a cementing lead carbonate. In a similar way, lead silicate was considered as the cement of quartz slime coating on galena. Experiments verifying this hypothesis were carried out according to the following procedure: Fresh mineral particles selected from the central part of the broken lumps and examined first under a microscope for ascertaining a clean surface were placed in a small beaker (1.5-in. dia. by 2.5 in. deep) half filled with one kind of slime pulp. The dilution of all slime pulp was 4: 1 and the particle size of slime was minus 400-mesh. After agitation for 5 min. the specimen was removed by a sharp-end tong and washed gently three times in three separate distilled water baths. It was dried before a small electrical fan and examined immediately under a microscope. A photograph was made of the observation. With reference to the published solubilities,4 several of these experiments, which contradict the chemical hypothesis, are listed as following: I. The coating of fluorite slime on the galena surface was light but the coating of galena slime on the fluorite surface was heavy. In a similar way, the coating of quartz slime on the galena was fairly light, but the coating of galena slime on the quartz particle was heavy. According to the chemical hypothesis, using the same constituents and regardless of which is the slime, the density of the coating should be expected to be the same. This, however, as shown above, is not true. Moreover, fluorite (CaF2), having a solubility of 16 mg.[4a] per liter of water, should not be

Jan 1, 1943

Jan 1, 1940

By V. K. Grotzky, F. J. Fraikor

A number of investigators have noted the importance of various precipitation reactions on the properties of commercial-purity beryllium.1-5 Carrabine, for example, has demonstrated the interaction of iron and aluminum on the mechanical properties of hot-pressed polycrystalline beryllium.6 He considered the determining factor on elevated-temperature properties to be a reversible AlFeBe, precipitation reaction which could be directly related to the Fe/Al impurity ratio of the beryllium. Any aluminum in excess of the stoichio-metric amount required to form A1FeBe4 was presumed to remain primarily in the grain boundaries. We have observed, by transmission electron microscopy, such a grain boundary effect after various heat treatments of beryllium sheet. The starting material in this investigation was bare-rolled beryllium ingot sheet (0.001 to 0.005 in. thick), in contrast to the hot-pressed powder utilized by Carra-bine. It should be noted from the ingot sheet analysis shown in Table I that the Fe/Al weight ratio was near unity which would provide some free aluminum although the total aluminum and iron content was still small. Fig. l(a) shows some aluminum or aluminum-rich precipitates in the grain boundaries of a beryllium foil which had been quenched from 1200°C into brine at -TPC. Similar grain boundary precipitates were found, particularly at grain boundary intersections, in other samples quenched from 1100° and 1000°C. The length of annealing time at these elevated temperatures did not appear to substantially alter the amount of grain boundary precipitates, thus attesting to their relative insolubility. No matrix precipitates were observed other than the normal BeO and Be2C inclusions. A microprobe analysis of the larger precipitates at

Jan 1, 1968

By W. A. McCurdy, Joseph W. Leonard, T. S. Spicer

INTRODUCTION by T. S. SPICER and J. W. LEONARD Utilization from the Point of View of the Preparation Engineer The primary interest of the coal preparation engineer is process design, operation and maintenance to produce an acceptable product which can be sold at the greatest possible profit. Because of these interests, attention to the unrealized potential value of coal is sometimes neglected. The intent of this chapter is to alert the preparation engineer to the utilization possibilities of both the product as well as the tributary coal flow moving through a modem coal preparation plant. Thus, coal types having similar physical and chemical properties tend to become increasingly concentrated according to size, specific gravity and/or surface chemistry. The basis for any unrealized potential derives directly from the coal seam itself. Most coal seams consist of coal bands and benches which are sandwiched together in layers and which visually differ from each other by physical structure and luster. Randomly selected physical and chemical ranges determined from layers of coal in a single seam can easily differ by as much as 30 Hardgrove grindability indices, 0.30 of a specific gravity point, 20 percentage points of ash, six percentage points of dry volatile matter and 10 percentage points of total sulfur.1 Similar wide variations exist for calorific value, seam moisture content and undoubtedly, for any other conceivable coal test parameter which might be used for comparative purposes. These observations all point to the long established fact that coal is not homogeneous as conventional analytical methods might tend to indicate, but is instead a highly heterogeneous substance. Since both coal and associated minerals entering a preparation plant are highly heterogeneous, a multi-product potential beginning with certain flotation cell concentrates and ending with plant refuse may exist. Such a potential can and to a limited extent is achieved at some operations by drawing off coal according to size, specific gravity and/or surface chemistry differences from individual coal cleaning processes. Such a sequenced draw-off of coal of increasing ash increments could yield, among other products, chemical coals, coking coals, coals for pulverized fuel boilers, cyclone boiler coals, coals for cement plants, limestone, shale and clay. Basis for Coal Evaluation and Selection Despite the known heterogeneity of coal, the final analysis of a given coal product is customarily reported as a single average since coal has always

Jan 1, 1968

By W. J. Keep

Some explanation of methods of testing will be given before presenting the record of a series of physical tests of aluminum, other metals and alloys. I. The Methods Employed and Meaning of Diagrams. The test-bars used, 12 inches long and 4 inch square, are cast in green sand, with chills bedded in such a way that the ends of the bar run against them. By splitting the ends of the bar the depth of chill can be measured. The chills being held in the mould 121/8 inches apart, the space between the end of the bar and the face of the chill, after both are alike cold, is the amount of shrinkage, and is recorded in thousandths of an inch per foot.

Jan 1, 1890

By Thomas M. Drown, P. W. Shimer

In a communication to this Institute at the Baltimore meeting, February, 1879,* on the "Determination of Silicon in Pig Iron and Steel," the method recommended was the treatment of the metal with nitric acid until action had ceased, and then evaporating with sulphuric acid until the nitric acid was nearly or quite driven off. After filtration of the siliceous and carbonaceous residue, and washing with hot water and hydrochloric acid, a silica was obtained, on ignition, which was quite pore. Since this paper was read before the Institute, we have had large experience with the method, and

Jan 1, 1880

By W. M. Johns

The word "Flatland" should read "Flathead" in the title of the paper by Willis M. Johns on page 184 of the June 1962 issue. The correct title is "Belt Series in Lincoln and Southwest Flathead Counties, Montana." In the same paper, reference 12 on page 191, the publication is Bulletin 12, Montana Bureau of Mines and Geology, rather than Bulletin 17.

Jan 1, 1962

By William Clark

A bean placed at the bottom of tubing in flowing wells is not a new idea. In fact, a device which in effect was a bottom bean was patented prior to 1890 by John D. Rockefeller. Because of the limited use of the bottom bean, prior to 1922, when it was installed in a few wells in the Santa Fe Springs field, California, the knowledge of the results of its operation is very meager. Since then various oil operators have experimented with bottom beans, but most of the records of the results obtained by their use are unavailable. For the past year or two, more attention has been directed to this method of producing wells; the theory and best means of application have been studied, and accurate records maintained. In theory, the use of bottom beans in flowing or gas-lift wells should secure certain advantageous results. With the exception of flow friction of the tubing and flow lines, there is no back-pressure held on the rising column of fluid. Thus severe beaning is possible with no danger of killing the well by too heavy a fluid column, a condition that often exists when a surface bean is used. The whole energy of the gas expanding to atmospheric pressure is utilized to lift the fluid in the well. The same effect is obtained when flowing a well through open tubing or casing. In using a surface bean this energy of expanding gas is wasted into the flow lines beyond the bean, because the fluid has reached the surface by the time the restriction is reached and the work of the gas performed. The bottom bean affords an efficient use of the expanding force of gas, utilizing less gas to raise the same amount of oil, hence allowing for lower gas-oil ratios. The flow restriction being at the entrance to the flow string, a more uniform mixture of gas and oil enters the tubing and a steadier backpressure is held on the well. The uniform mixture and high velocity attained while flowing through the bean, which is above the critical velocity required to suspend a spray condition of gas and oil, prevent slippage of gas, surging and heading with its resultant strain on the casing. The advantageous conditions allow positive control of production in gas-lift wells within limits set by the bean size and amount of input gas; and probably help to prevent sanding up of a well and the coning

Jan 1, 1931