Search Documents

By Jay R. Burns

Two magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or AM265 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains g per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,1,2 however, demonstrates that H and C alloys are replaced by A8 and AZ91, respectively. That is, A8 represents a magnesium alloy having superior toughness while AZ91 is suitable for high yield strength and pressure-tight applications. The basic difference between the American and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars.3 In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ91 alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. [ ] The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity5 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

By Stuart M. Buck

The term "splint" seems to have been adopted to describe the fracture of the hard bituminous coals of West Virginia. It is not a scientific name, but rather a trade term, and does not indicate a correspondence with English splint. At present it is a popular word, and is very loosely applied to coals of various qualities, in the desire & improve their sale. The Kanawha splint is distinguished by its hardness, dull lustre, coarse fibrous structure, its purity, and especially its resistance to atmospheric influence. It kindles very readily, burns with a bright flame, but does not cake, so that a lump when half consumed, may be broken by a slight blow in its plane of cleavage, though it will resist a strong blow in any other direction. I have seen pieces that have been exposed to frost and sun

Jan 1, 1882

By Bruno Nordberg

HOISTING is one of the earliest endeavors of man with machinery, for hoisting was probably used by the early Egyptians. Treadmills were used for general hoisting until early in the nineteenth century and it was a short step only to attach a Watt steam engine to the rope drum of a hoist. One of the earliest steam hoists was built for a coal mine at Frisne, near Valenciennes, France. It was a remarkable piece of engineering created by James Watt in 1811, using a wooden drum on a vertical shaft. This followed the crude hoist by Holtzhausen in 1803, which used a drum of wood on a horizontal shaft.1 In this country there were examples of crude mine hoists, which have been developed into the efficient machines in use today. African and Australian mines show examples of both extremes, and have an array of fine hoisting equipment exemplified in those built by British manufacturers. The influence of both English and American engineering in hoisting is interestingly evident in Canada. The information available to the writer does not reveal this to be true of South Africa, although American-built hoists have been furnished. Mining camps develop their own style of equipment, adapted to local conditions. For instance, the Butte mining district adheres to the straight drum with friction clutches, because of the great number of levels from which hoisting is done or to which men and material are lowered and the necessity for hoisting or lowering unbalanced. The north Michi-gan copper country uses both straight and cylindroconical drums and hoists continually in balance, so that the drums are not clutched to the main driving shaft. The Joplin mining district, Missouri, has its own peculiar small hoists. Other individual mines or localities in which a number of mines have been developed show individualisticc types of hoists, depending upon their particular problems. In each instance, however, the particular problem must be carefully analyzed, as conditions are seldom so near the same that a number of identical hoists can be used to advantage.

Jan 1, 1940

By Noel Stearn

OF THE many instruments devised for the measurement of magnetic anomalies, the ordinary dip needle, by virtue of its superior simplicity of construction, facility of manipulation, and definiteness of interpretation, seems to merit serious attention as the instrument most readily applicable to the detection of magnetic anomalies of the higher order of magnitude. , In spite of the fact that it has been used for many years for the discovery of iron ore in Europe and in the Lake Superior region of America, its capabilities as a geological instrument have not yet been thoroughly plumbed. The Wisconsin Geological Survey, under Dr. W. 0. Hotchkiss, E. F. Bean, and H. R. Aldrich, has been most thorough in developing the technique of the instrument, and the results it has obtained have aroused a general interest in a more widespread use of geomagnetics as an exploration method and the dip needle as a geological instrument. The simplicity of the instrument is an especial advantage, as it can be used by anyone, regardless of his technical training; but to insure useful results not only is a knowledge of the background of geomagnetics necessary but also an understanding of the principles of the instrument itself.

Jan 1, 1928

By Harry P. McClintock, Alec M. Crowell

Production of oil and gas condensate from the 45 oil and gas fields of South Arkansas increased for the eighth consecutive year, the production for 1943 being 27,605,647 bbl. Six new pools were discovered during 1943, bringing the state's crude oil and condensate reserve to 475 million barrels, a net increase of 70 million barrels for the year. The gross increase in proven reserve was 98 million barrels, from which, of course, is subtracted production of approximately 28 million barrels to reach the net figure of 70 million barrels. There were 35 more wildcats in 1943 than in 1942, and 29 more wells were drilled in fields of the state. Sixteen companies operated exploratory crews during the year for a total of 677 crew weeks, divided as follows: 563 weeks seismograph, 111 weeks gravity and 3 weeks core drill. There was a decided increase in gravity work and a decrease in seismic work. The year started with 15 seismic crews and ended with 5 seismograph and z gravimeter crews. Geologically, it is interesting that the number of wells bottomed in Gulf, Comanche, and Jurassic strata were near equal for the year 1943. During 1942 Jurassic was much higher than the other two. However, Jurassic still led in wildcats for the year 1943. Abandoment of wells in the stripper areas of the state reached about the same figure for the year 1943 as for the year 1942; that is, 145 wells were permanently abandoned. However, 243 wells were drilled in 1943, as against 184 for the previous year. The completions for the year were divided into 103 dry holes, 137 oil and condensate wells and 3 dry gas wells. Among new developments perhaps the most significant was the pressure-main-tenance project for the Midway field of Lafayette County, which is utilizing fresh water as the maintenance medium. This is the first fresh-water pressure-maintenance operation during primary production of an oil field in the United States. The operator of the project, Barnsdall Oil Co., estimates that the ultimate recovery of oil from this field will be increased from 32.5 to 65 million barrels. The Midway pool is of the dissolved-gas type, but a similar project is getting underway for the Magnolia field, Columbia County, a pool of the gas-cap and water-drive type. Dual completion of wells, on concurrent production from two productive zones through a single well bore, became common practice in South Arkansas during the year. As the year ended, some 50 wells had been dually completed and it was estimated that the first 37 of these wells represented a saving of more than 2 1/4 million dollars and a saving in steel of 7000 tons. The majority of the wells dually completed were those reaching depths in the neighborhood of 9000 ft. below the surface and initially productive there. Selective completion at lesser depths in the same well bore proved mechanically feasible and economically sound. The year was marked by the successful completion and placing into operation of three large natural-gas desulphurization

Jan 1, 1944

By d&apos, D. L. Guernsey, J. C. Entremont, John Chipman

The reaction of aluminum with oxygen in liquid iron has been studied at 1740° and 1910°C. Interaction coefficients are very much smaller than those previously published. The equilibrium constant falls within the approximate range of earlier experiments and calculations. It is now well established that the "deoxidation constant" for aluminum in liquid steel at normal steelmaking temperatures is extremely srnall. Thus at 1600 the product [% Al] is of the order of 10- 14. At this temperature, therefore, great experimental difficulties are encountered in any attempt to obtain a direct measure of the constant. If the aluminum content of the metal is high enough to permit accurate analytical determination, that of the oxygen is too low. If the oxygen content is high, the aluminum is below the limits of detection. Our best values of the constant have come, therefore, from indirect calculations or by extrapolation downward from observations at higher temperatures.. For their studies in the range 1695° to 1866°C, Gokcen and chipman' restricted their aluminum concentrations to less than 0.06 pct. Oxygen analyses were made by the vacuum fusion method which appears to be dependable at these low aluminum concentrations. Experimental results, even at the highest temperature employed, are extremely sensitive to small errors in the analysis of either element. The slight change in the equilibrium constant with aluminum and oxygen concentration was utilized in the calculation of interaction coefficients expressing the effect of aluminum on the activity coefficient of oxygen and the reciprocal effect of oxygen on the activity coefficient of aluminum. The range of concentration, however, was so limited that only a rough value for the interaction coefficient could be obtained. This value was much more negative than that found for any other pair of reactants. In view of the very limited range of concentration employed, the reported values have always been regarded as very questionable. A redetermination was the object of the work reported here. EXPERIMENTAL METHOD At high aluminum concentrations, the vacuum fusion method is susceptible to grave error due to absorption of gas by aluminum distilled from the sample. Since it was desirable to extend the study to at least as much as 1 pct Al, another method for analysis was sought. In steels containing more than a few hundredths of a percent aluminum and no other deoxidizing element, it is safe to assume that

Jan 1, 1963

By Simon H. Ash

The coal-mining districts of Washington are mainly west of the Cascade Mountains; Fig. 1. The mines are on the foot hills of the slope, the lignite fields of Lewis and Thurston counties extending into the valleys west of the mountains. An exception is the Roslyn field, a small but important area on the eastern slope. If western Washington is divided into three areas from north to south, the bituminous coal fields and most of the active operations will be found largely in the middle area. The southern portion contains lignites over a large area. In the northern portion, mining is practically restricted to one mine, the Bellingham, which is working a subbituminous coal seam near the city of Bellingham. The degree of alteration that the coal of a particular field has undergone may be gaged roughly by the position of the field with reference to the Cascade Mountains. The lignites of Tenino, Tono, Mendota, and Castle Rock, on the railway line connecting Seattle and Portland, occur in a region of low relief, in which the Eocene coal measures have suffered only minor disturbances. Subbituminous coals occur in the foot hills, as at Renton, Newcastle, and Bellingham. Coalg high in fixed carbon are found nearer the mountains, where the measures have been sharply tilted and folded, as at Black Diamond and Carbonado. The two typical anthracite fields are located still higher, in the rugged mountains where outcrops appear both in deep gorges and on ridges at elevations approaching 5000 ft. At Carbonado is found the only semianthracitc seam worked on a commercial basis. The occurrence of this seam in a region of bituminous coal is due to the nearness of an igneous sill, which has changed its character from bituminous to semianthracite. Purpose of Paper On account of the various faults and dips and the varying nature of the wall rock, many difficulties are encountered in mining and winning the coal. The paper gives some of the methods used in mining and, in some detail, the conditions that affect the efficiency of these methods.

Jan 1, 1925

By Arthur C. Simmons

Production of oil within the state of Pennsylvania in 1940 was slightly more than the 1939 total, and this increase was due entirely to the new flush Music Mountain field south and west of the main Bradford pool. The influence and magnitude of Music Mountain production will be separately described, inasmuch as it is an important producing unit within the state. Production Bradford Field The production listed herein for Bradford field includes only the part of the field that is within the state of Pennsylvania. Approximately 4000 bbl. per day, or 10 per cent of the total Production of Bradford field comes from Cattaraugus County, New York, and should properly be attributed to production obtained within the New York state area, although locally and economically the Bradford field, situated both in New York State and Pennsylvania, is included as a single statistical unit. The 1940 average production in the Bradford field was 34,831 bbl. per day, as compared with a daily average in 1939 of 35,340 bbl., or a decrease from 1939 of 509 bbl. per day. The decrease in production from the Pennsylvania portion of the Bradford field would have been more pronounced if a portion of the crude from the Music Mountain field were not included with the statistics for Bradford field. The decline can be attributed largely to the fact that more properties of lower average recovery were being drilled in 1939 and 1940 than in previous years, and apparently a subnormal amount of drilling occurred in 1938 and 1939, when about 2100 wells were drilled each year. The full effect of the 1940 drilling is not felt immediately and undoubtedly will affect the producing period of 1941. It appears probable that the water-flood area in the Bradford field has reached a definite peak unless some unusual economic condition should cause abnormal prices and an excessive rate of development such as occurred in 1936 and 1937. Virtually all of the production in the Bradford field was obtained by water-flooding methods, as natural or stripper wells are uneconomical and air and gas repressuring have not proved so efficient as water-flooding as a secondary recovery method. Central and Southern Pennsylvania Central and southern Pennsylvania produced a total of 4,604,763 bbl. of oil during the calendar year of 1940; that is, an increase over the 1939 total of 166,728 bbl. The daily average production was 12,581 bbl., or an increase over 1939 of 422 bbl. per day. Table I includes the total oil production for the state of Pennsylvania for the years 1937 to 1940, inclusive, and the daily average for each of these years. It is impractical to make a complete subdivision by districts, consequently the only segregation is the production from the Bradford field (within the state of Penn-

Jan 1, 1941

By P. A. Fisher, J. B. Wilson, D. J. Whitehead, C. J. P. Ball, A. C. Jessup

The properties of a new magnesium alloy ZT1 containing 3.0 pct Th, 2.5 pct Zn, 0.7 pct Zr are described. The alloy possesses good creep and fatigue resistance up to 650°F, is free from microporosity, and is readily sand-cast. ZT1 is shown to be superior to zinc-free Mg-Th-Zr alloys. THE advent of the jet engine created a demand for a light sand-casting alloy capable of being cast into large complex shapes and capable of resisting creep at temperatures up to 500°F. This demand has been largely met by alloys of the magnesium-cerium mischmetal-zirconium types, containing about 3 pct Ce mischmetal and 0.7 pct Zr, typified by Elektron magnesium alloys MCZ and ZREI, the latter alloy also having a zinc addition of 2.5 pct. These alloys utilize the valuable properties at elevated temperatures conferred by the addition of rare earth metals to magnesium, a fact which has been known for many years and discussed by several investigators.1-1 Murphy and Payne8 showed that the addition of the powerful grain-refining element zirconium to Mg-Ce mischmetal alloys produced alloys with attractive room temperature properties combined with good creep properties and castability. With the increasing power of modern jet engines the temperatures to which some of the magnesium parts are subject are likely to exceed the safe working range of the cerium-mischmetal-containing alloys, and at the beginning of the research considerable interest had been shown by aeroplane engine designers in a magnesium sand-casting alloy suitable for service at higher temperatures, e.g., 600°F and above. At an early stage in the development of this type of alloy a check on the fatigue properties at elevated temperatures indicated that, since the fatigue limit even at 108 eversals was appreciably higher than any permissible creep stress, the main emphasis of the research could be concentrated on creep behavior. The primary aim in developing the new alloy has therefore been to attain maximum creep resistance; but due consideration has also been given to other important properties such as castability, tensile strength, and cost. It is by now well established that it is not possible to correlate creep strength with other short time mechanical properties such as are obtained in tensile

Jan 1, 1954

By John V. Beall

As recently as 1964, the situation in the Australian iron ore industry was chiefly one of potential. The only producer was the Broken Hill Pty. (BHP). That company mined about 5 million tpy from deposits in the Middleback Range in South Australia and at Yampi Sound in Western Australia. No ore was exported from Australia. Now, just five years later, and after expenditures amounting to approximately one half billion dollars, BHP and seven new companies exported about 15 million tons (long tons) of iron ore and pellets as well as meeting Australia's own annual requirements of approximately 8.5 million tons of ore. Early this year, the volume of iron ore on order stood at 328 mil- lion tons to be delivered over a period of 15 years, but Cliffs Western negotiations for sale of Robe River iron ore have boosted the volume to the new high of 466 million tons. All of this has meant a great deal to Australia in terms of new income. In fiscal year 1967 (ending June 30, 1967) exports of iron ore amounted to $52 million; in 1968, $128 million and by 1'972 the Bureau of Mineral Resources expects the value of exports from iron ore to reach $242 million. In achieving the position of major- supplier of iron ore to the Japanese steelmakers, it was necessary to build a great many new facilities, mostly in Western Australia. Three railroads, 70 miles long, 182 miles and 265 miles were constructed. A new port was created at Dampier; Port Hedland was deepened and otherwise improved; both of these ports are in Western Australia. In Tasmania, Savage River developers built an offshore shiploading station that has received the recognition of engineers internationally. At least a half dozen new communities have been founded. The narrow gage railroad from Kalgoorlie to Perth and Freemantle was replaced with a standard gage line.

Jan 6, 1969

Jan 1, 1907

By John T. Eash

During the course of the war the supply of tin in this country has steadily decreased and a continued effort has been made since the beginning of the emergency to use alloys that are either tin free or contain appreciably lower quantities of it. Even with the use of emergency materials, the tin supply has become particularly acute, and it is estimated that after recovery of the far eastern mines probably one to two years will be required before our normal annual supply is attained. One of the major tin-consuming fields is the bronze industry. Recommendations were made several years ago by the War Production Board toward the use of bronzes of lower tin content and manganese bronze and yellow brass for the customarily used tin-bronze alloys. The substitution of 88-5-5-2 copper-nickel-tin-zinc for composition G received considerable attention before the war, and consequently this alloy and modifications of it have been adopted for some current structural and pressure castings requiring high mechanical properties. Another of the commonly used bronzes is the 10 per cent tin 10 per cent lead copper alloy for heavy-duty bearings. It has been known for some time that about 2.5 per cent nickel could be substituted for an equal amount of tin with retention of equivalent casting and tensile properties; however, it was desirable that a still greater conservation of tin be made. Consequently the present paper deals with the development of an alloy of low tin content that could be used for bearings. Selection or Composition While the final criterion of the suitability of an alloy for a bearing must of course be determined by practical applications where all the ramifications of service conditions are encountered, certain short cuts in the initial selection of compositions are necessary to avoid an extensive and time-consuming investigation. The present program has been to match certain metallurgical properties of the 80-10-10 bronze that have been shown by previous investigations to be related to good bearing qualities. Such properties as microstruc-ture, hardness, compressive yield strength, ductility, and castability have been considered, and certain simple wear tests have been made. Of the readily assessed characteristics desired in a good bearing alloy, one can be certain that a uniform distribution of lead is required in a leaded bronze. It has generally been found that segregation of lead is one of the chief difficulties with this type of material. Tin has a powerful effect on lead distribution, and with 10 per cent present produces a random distribution of chunky particles, such as are shown in Fig' 1. I' In the tin bronze contains the hard alpha + delta

Jan 1, 1946

By F. A. Forward, A. H. Ross, J. Halpern

IN treating carnotite ores by carbonate leaching it is often necessary to subject the ore to a prior roast. Among the advantages that may result from roasting are: 1) improvement in settling and filtering characteristics of the ore; 2) destruction of carbonaceous impurities that would otherwise contaminate the leach solution and consume carbonate reagent; and 3) substantial increase in extraction of vanadium, which is usually low when the un-roasted ore is leached. Recovery of vanadium may be an important factor in processing carnotite ores, and the fact that vanadium is usually recovered in good yield by acid leaching has often been an economic advantage over results obtained with carbonate leaching. It has been found that response of an ore to carbonate leaching, following roasting, depends primarily on its composition and on the conditions of the prior roast treatment, particularly with regard to the roasting temperature, the atmosphere maintained above the charge during roasting and cooling, and the presence of certain reagents. These factors, especially the last, virtually determine the extractions of uranium and vanadium attainable by carbonate leaching, as well as the reagent consumption on leaching, whereas adjustment of the leaching conditions has only a limited influence. These variables were examined systematically to elucidate roasting and carbonate leaching of carnotite ores and to establish a treatment yielding high recoveries of both uranium and vanadium. Tests were conducted on samples of four different Colorado Plateau ores, described in Table I. Roasting Procedure: The roasting tests were conducted in an electrically heated furnace in which the temperature was controlled to +15oC. The ore (usually a 500-g charge) was ground to —100 mesh, mixed with the desired reagent, and spread in a silica tray to a bed depth of about 1/2 in. During the roast the charge was rabbled at intervals of 15 min. To provide free access of air the furnace was usually ventilated; however, in a few experiments a controlled atmosphere such as carbon dioxide or hydrogen was maintained above the charge. Leaching Procedure: The pulp, generally comprising 500 g of ore and a 2000-cc solution containing 80 g per liter of Na2CO3 and 20 g per liter of NaHCO3, was agitated in an autoclave at 120°C, under 30 psi O2. Samples were withdrawn periodically, and the solution and ore residue were analyzed. Under the conditions employed, maximum attainable extractions were generally achieved in 4

Jan 1, 1958

By Clifford C. Hanninen, Allan H. Caverson

Within the past nine years a means for measuring the distance between mine roof and floor was developed at the White Pine mine which yields relevant information utilized in the mining operation. The technique known as "convergence" is an efficient, low cost way for obtaining large quantities of data for predicting roof falls, caving activity and overall mine stability. Since 1964 the activity of convergence measurements has expanded to become a production tool found in all sections of the mine. The program involves four types of activity: 1) monthly measurements in areas known to be active and in sample blocks scattered throughout the mine for a long-term stability study; 2) semi- monthly measurements along vital travel roads, belt drifts and compressor sites; 3) weekly measurements in areas where men are working; 4) daily measurements in pillar-recovery and caving operations.

Jan 5, 1973

SECTION I PAGE PAGE Bulletin Wanted v Northwest Mining Convention St. Louis Meeting v (Columbia Section) xvi Proceedings of the Meeting of Affiliated Student Societies... xvii the Board of Directors vii Harrison W. Craver, New Li-¬ John Fritz Medal viii brary Director xviii Herbert C. Hoover, Food. Con Library xx troller viii Pamphlets for Sale xxii President's Prize ix Membership xxxvi Emmons Memorial Fellowship. x Biographical Notice of Her¬ Meetings of Various Societies. x Mann A: Keller : lviii Personal xi Institute Committees lix Employment xii Officers and Directors lxvi Local Section News xiii

Jan 5, 1917

By H. W. Norman

DURING the first few years of the new atomic age the Colorado Plateau was the focal point of uranium exploration. There was little incentive to expend time and effort in an area so far removed from the known deposits as the Pacific Northwest, and there were too few local prospectors to cover the vast territory involved. In 1949 the AEC established an exploration office in Spokane to evaluate the uranium potential of the northwestern states. Interesting occurrences were found in the Coeur d'Alene district in Idaho and in the Boulder Batholith of central Montana, but the AEC discontinued the Spokane office in 1952, and for the next two years prospecting in the area was negligible. In April 1954 John and James LeBret, prospecting on the Spokane Indian Reservation with an ultra violet lamp, located an occurrence of the fluorescent uranium mineral autunite. This discovery was not announced until the following September, after a lease had been granted by the Spokane tribe. Exploratory drilling carried on by the AEC throughout the winter verified the existence of a commercial orebody. This property, the Midnite mine, has since developed the largest known ore reserve in the district.

Jan 6, 1957

By C. A. Allen

For over three years we have been endeavoring to reduce the number of fatalitics and minor accidents in Utah. The physical condition of the FIG: 1.—Number kiLlEd per million short tons of coal produced in ColoraI)o, New Mexico, utah, Wyoming, and bituminous mines of the United States 1014 to 1920. mines, concentrators, and smelters is good, yet the number of accidents,

Jan 1, 1923

By E. S. Bumps, H. D. Kessler, M. Hansen

The titanium-rich end of the Ti-AI phase diagram has been determined to the compound TiAI3 (62.7 pct Al), thus joining the aluminum-rich portion previously investigated by others and completing the diagram. Micrographic analysis and X-ray diffraction were the chief methods used to determine the phase relationships. THE Ti-Al phase diagram has been investigated as part of a program on titanium phase diagrams for the Wright Air Development Center. Included in the available information concerning the phase relationships in titanium-rich Ti-A1 alloys is a brief statement by Brown' that: "aluminum raises the transformation temperature to 1000°C (183Z°F)." This observation is interesting in that it is the first example of a metallic alloying component raising the transformation temperature of titanium, and consequently widening the field of the a solid solution. Busch and Freyer' presented resistivity data which indicated the formation of titanium-rich solid solutions of 1 and 3 pct A1 alloys prepared by powder metallurgy methods. Duweza found that there is only one other intermediate phase other than the known compound TiA1, (62.7 pct Al). This phase, designated as y, is of variable composition; its crystal structure is of the AuCu type and is therefore based on the composition TiAl (36.02 pct Al). Earlier work on the constitution of the aluminum-rich alloys has been reviewed by Hansen, and need not be discussed here. The tetragonal crystal lattice of TiAl,, as found by Fink, Van Horn, and Budge," was confirmed by Brauer." Recently, Schubert7 has reported that TiA1, is homogeneous within a limited composition range; however, the solubility limits were not given. The Ti-A1 phase diagram as presented in. this paper was determined by micrographic analysis of alloys containing from 1 to 62 pct Al, annealed at and quenched from temperatures between 700" and 1400°C. The phases and phase ranges investigated extend to the compound TiA1, (62.7 pct Al) to join the aluminum-rich end of the system determined by other investigators, thus completing the diagram. Methods of Investigation Preparation of Alloys: Iodide titanium, 99.9+ pct pure, obtained from the New Jersey Zinc Co., and high-purity (99.99+ pct) aluminum sheet from the Aluminum Co. of America were used to make up alloy ingots weighing 10 to 20 g. Detailed descriptions of melting techniques have been presented previously for work on the Ti-Mo and Ti-Cb> nd Ti-Si" phase diagrams. Briefly, the melting practice consisted of arc melting an accurately weighed charge in a copper block crucible insert in a non-consumable tungsten electrode furnace, under helium at atmospheric pressure. All ingots were carefully weighed after melting to detect possible losses. Comparison of weight before and after melting showed no appreciable weight changes. Also, chemical analyses were in close agreement with nominal compositions, Table I. The diagram as presented is, therefore, based on nominal compositions. Alloys were prepared having the following nominal aluminum contents: 1 ... 36 (1 pct increments), 38, 40, 41, 42.5, 44, 45, 46, 47.5, 49 . . . 64 (1 pct increments), 67, 70, 80, and 90. Ingots with up to 14 pct A1 were cold-pressed various amounts in order to increase the rate of attaining equilibrium structures on heat treatment. The amount of cold deformation that could be applied decreased with increasing aluminum content, until alloys containing 12 pct A1 or more cracked after only a few percent deformation. Annealing Treatments: Samples annealed at temperatures of 700" to 1000°C were sealed in

Jan 1, 1953

By M. E. Shank, J. Wulff

In view of the current interest in magnetic materials having rectangular hysteresis loops, as for example those obtained with the grain oriented 50 nickel 50 iron alloys,t we wish to call attention again to the results obtainable with the perminvar (Co-Ni-Fe) alloys heat treated in a magnetic field. Data taken from direct current measurements made prior to and during World War II give the typical values shown below for two of the perrninvar alloys. Fig 1 and 2 show- the hysteresis loops for these samples. The first sample above consisted of small rings punched from 0.014 in. sheet stock. These rings were heat treated at 1000°C for one hour in a hydrogen atmosphere and then cooled with the furnace to 750°C at which point they were subjected to a magnetic field of 15 oersteds maintained during cooling to room telmperature. The molybdenum perminvar sample consisted of a spirally wound core of 0.001 in. tape. The heat treatment was the same except that box annealing methods were used and no hydrogen atmosphere was employed. Even better properties might be expected using hydrogen. The heat treating temperatures and cooling rates are not critical. Rectangular hysteresis loops produced in other perminvar alloys by heat treatment in a magnetic field were described earlier.',? Properties similar to those described above are realized in perminvars manufactured by conventional methods. Drastic cold working which in practice limits the final thickness and is gen- erally expensive may thus be avoided. This information may be of interest to those concerned with magnetic alloys and the development of contact rectifiers, magnetic amplifiers and so on.

Jan 1, 1950

As it is the plan of the War Department to return 400,000 soldiers a month during the next four months, Colonel Arthur Woods, Special Assistant Secretary f War, has requested the Engineering Societies to assist the Government by soliciting their members to advise the respective societies, at the earliest possible moment, f any place where companies can employ returned soldiers. This request applies not only to the professional men who are returning but also to the miners, mechanics and other skilled labor among the enlisted men. Army discipline has not only made these men think more quickly but also more willing and obedient workers. The whole training has been conducive to regular habits and clean living steadying these men and fitting them to meet emergencies more quickly and has instilled more loyalty to their superiors and to their jobs. Further, the military instruction they have received has increased the men's powers f concentration. The War Department cannot too strongly bring before the employers of skilled labor the fact that the employment f discharged soldiers will be advantageous to the employer and economically beneficial to the country. The following is a list of the vocations of the men who are now returning:

Jan 6, 1919