Search Documents

By Howard Thompson, H. N. Hall, Frank Nuss

Removal of bit cuttings is an important function of drilling muds. In an effort to obtain better understanding of the factors influencing the removal of cuttings, an extensive series of laboratory tests were made in which slip velocities of various sizes and shapes of particles were measured in muds of different physical properties. Empirical equations were then derived from these experimental data. These equations show that slip velocity is dependent on cutting size and shape, mud flow constants, and flow state of the mud. Applicability of these equations for field use is demonstrated by comparing computed slip velocities with slip velocities obtained from field tests. Drilling muds have many functions, but perhaps the most important is the removal of bit cuttings from the well. In a 10,000-ft well, the weight of rock which is drilled and must be carried to the surface is over 150 tons. In addition to this, the mud must remove any sloughings from the well bore. Failure of the mud to promptly remove either bit cuttings or sloughs from the well bore causes re-drilling and excessive wear on bit teeth, slows down drilling rate thereby increasing well costs, and greatly increases possibilities for stuck drill pipe when circulation is stopped for any length of time. Drilling muds lift bit cuttings to the surface by means of the upward velocity of the drilling mud in the annulus. Because a density difference exists between the rock being drilled and the drilling mud, there is a difference between mud velocity and the rate of bit cutting travel, called the net rise velocity. To evaluate the ability of any type of drilling mud in respect to lifting cuttings, some method must be known for predicting the rate of fall of cuttings through mud traveling upwards in the annulus. Equations for the rate of fall of particles through a true fluid have been satisfactorily determined by several authors. 1-6 Since drilling muds are not true fluids, but obey the laws of Bing-ham,7 it should not be expected that equations for rate of fall of cuttings in a true fluid would be applicable to plastic fluids such as drilling muds. Several authors have attempted to compute cutting slip velocities in muds using a viscosity value obtained with a Stormer viscosimeter; however, unsatisfactory results were obtained. Pigott8 took cognizance of the phenomenon of variation of viscosity with velocity in laminar Row, and calculated laminar slip velocities using a variable viscosity with Stokes law, and turbulent slip velocities using Rittingers law. Drilling muds obey the laws of plastic flow which involve factors not affect-

Jan 1, 1950

By W. W. Wirth

RESEARCH looking toward the reduction of the cost of roof support by substitution of longer-life materials for wooden timber is fully justified by the fact that roof support is an important element of all production costs. Permanent or semipermanent roof support will reduce the expense of timber-maintenance crews during steady operations, but even more markedly during idle periods. The management, therefore, is faced with the important problem of timber renewals, which in times of regular operation are frequently obscured by more urgent problems of production. Increased use of timber in the Anthracite Region of Pennsylvania is caused mainly by increased percentage of coal obtained from robbing areas, which requires more timber for safety than develop-ment work, and maintenance of long haulageways through crushed ground despite the fact that less coal is transported over them. The timber reserve in the immediate vicinity of the mines has been depleted to such an extent that it is necessary to secure 70 per cent of the timber requirements from distant sources. Originally, mine timbering in this region was done by largely utilizing round props or legs with round collars. The whole cross section of the tree from which timber was cut was utilized by forming the joints between the legs and the collars with saw and adze, using plank or round saplings for lagging behind the legs and over the collars to prevent material falling between them. The Mine Inspectors' report of 1898 records an important digression from the use of round timber, when two tunnels at the Babylon colliery, near Pittston, Pa., were timbered with 12 by 12-in. square timber sets with mud sills, through quicksand for distances of 425 and 160 ft., respectively. The timbers were lagged with 3-in. plank to control sand.

Jan 1, 1940

By Linn Bradley, W. W. Strong, H. D. Egbert

Marked differences of opinion have been expressed by engineers interested in cleaning iron blast-furnace gases for use in hot-blast stoves and under boilers, in reference to the advantages of a hot-dry method over a cold-wet method. One point at issue involves the sensible heat energy in the moisture contained in the gas. Some advocates of the cold-wet methods claim that the condensation and resultant removal of the greater portion of this contained moisture by wet scrubbing, spraying or similar methods, results in a saving of some of this sensible heat energy, by reason of the fact that water vapor has a high capacity for sensible heat energy and may carry from the exit of a hot-blast stove, for example, more heat units than are sacrificed or lost when the gas is cleaned by this cold-wet method. Other advantages claimed for the latter method are: That gas burns more readily when it is free from moisture in any form; that because gas is made denser by cooling and removing the moisture it has a higher calorific value than hot gas carrying moisture; and that higher flame temperatures are obtained when the gas is cleaned by the cold-wet method. A search through the available literature fails to disclose any extensive calculations or records of conditions obtained in practice, bearing upon these phases of gas cleaning. This paper deals with these problems from the standpoint of the economy of using a gas of higher flame temperatures, of improved stove design, and of economy in the gas-cleaning department. Calculations have been made which show that by cleaning the gases by a cold-wet method the sensible heat energy of the blast-furnace gases is greatly reduced; and, in general, this loss of heat energy is far greater than that lost from the stoves or boilers due to the sensible heat capacity of the water vapor if carried away by the exit gases. By making use of the

Jan 1, 1917

By F. J. Mehringer, C. W. MacGregor

VARIOUS investigations have been carried out to determine the effects of cold-rolling on the common physical properties as represented by the yield strength, tensile strength, percentage of elongation and ordinary reduction of area. Very little information is available in the literature with reference to the effects of cold-rolling on the true stress-strain properties. Since the ordinary physical properties base both the stresses and the strains on the original dimensions of the test piece, which are greatly changed during the test, they are essentially empirical values and do not represent physically either true stresses or true strains. Consequently, they do not give an accurate picture of the effects of different conditions, both mechanical and metallurgical, on the strength and ductility of the material. It is not, however, the purpose of this paper to review the various advantages accruing from the use of true stress and true strain values, since these have been shown elsewhere,1-12 but to utilize them in representing the various effects considered. The true stress S and true strain (e = q') values mentioned above for the tension test are defined by1 [ ] where P, A, Ao are the axial load, the instantaneous area and the original area of cross section, respectively. From simultaneous readings of the axial load and the dimension or dimensions determining the instantaneous area of cross section, the true stress-strain curve is constructed by using the relations given in Eq. I. It is then the object of this paper to discuss the general effects of cold-rolling on the true stress and strain values for a low-carbon steel together with the effects of age-hardening and directionality on these properties. PRELIMINARY INVESTIGATIONS The material considered throughout the paper is a low-carbon steel of the following chemical analysis: C, 019 per cent; S, 0. 118; P, 0.092; Mn, 0.85; Si, 0.01. The stock was received in bars, 7 by 3/4 in., and was first annealed for one hour at 1650°F. followed by a furnace cool. Photomicrographs of this material showed considerable directionality even in the annealed condition. In view of the possible effects of the nonhomogeneity and directionality in this material, it was considered important to investigate their influence on the true stress-strain diagrams. In addition, the effect of strain-aging in this steel was also made the subject of a preliminary study. Elect of Aging on True Stress-strain Properties Since a certain time element would elapse between the cold-rolling operation and the final tension tests, it was determined to investigate the aging character-

Jan 1, 1945

United Engineering Trustees, Inc. GEORGE A. EASLEY H. G. MOULTON A. L. QUENEAU The Engineering Foundation GEORGE D. BARRON E. DEGOLYER A. L. QUENEAU Engineering Societies Library Board H. K. MASTERS A. B. PARSONS, Ex-officio F. F. SHARPLESS H. H. SWEETSER ARTHUR L. WALKER

Jan 1, 1934

By R. W. Raymond

Since the foregoing paper (see p. 387) was printed, I have received the decision of Judge William E. Church, of the first District Court of Dakotah, in the case of Michael Duggan et al. v. John H. and Frank J. Dnvey (Silva Terra—Sitting Bull case), published in full in the Black Hills Weekly Pioneer of August 9th, 1584. The journal mentioned gives also several interlocutory decisions rendered in earlier stages of the case; but I shall quote here only so much of the final decision as bears upon the .construction of the Revised Statutes concerning the apex, the end-lines, and the extra-lateral mining right, together with a sufficient statement of the facts of the case to explain the scope of the decision. " This is an action in equity, brought in the first instance to restrain a threatened trespass by the defendants upon certain mining property in the possession of the plaintiffs, known as the ' Silver Terra' claim ; the allegation being that the defendants were about to enter, through underground workings, the ground of the plaintiffs, and remove therefrom valuable bodies of silver ore. " The answer of the defendants, admitting the acts constituting the alleged threatened trespass, further averred that they had, in fact, at the time complained of, reached and passed, in their underground workings, throngh and beyond the vertical side-line of the Silver Terra claim, and therenpon justified the acts complained of, and claimed the right to pursue their workings into and through the Silver Terra ground, by virtue of their alleged proprietorship of a vein, lode, or ledge of rock in place, hearing silver, having its top or apex within the lines of a certain other mining claim called the ' Sitting Bull,' of which they claim to be the owners, which vein, lode, or ledge extended in a continnons body of mineral-bearing rock from such top or apex to the ground in controversy, and constituted the body of ore in dispute; and that it was in the pursuit of this vein, lode, or ledge in its downward course that they had passed beyond the vertical side-lines of the Sitting Bull claim, and for some hundreds of feet beyond, into the ,ground in controversy " Subsequently, a supplemental complaint was filed, setting up the entry into plaintiffs' ground by the defendants, and their claim of right to do so, and asking fnrther relief by a decree restraining the assertion of such claim, and quieting the title of plaintiffs. "The case was tried before the court without a jnry..... " Custer hill, upon which these claims are located, is situated in the village of Galena, in Bare Butte mining district, in this county. The village lies at the base of the western slope of the hill, which presents a lateral face from south to north

Jan 1, 1884

By R. N. Kust, J. C. Agarwal, H. E. Barner, N. Beecher, D. S. Davies

Kennecott Copper Corp. has developed a new hydro-metallurgical process for extracting nickel, copper, cobalt and molybdenum from manganese nodules. This process (KCC Cuprion Process) utilizes a reduction leach operating at atmospheric pressure in the temperature range of 45 OC to 50°C and has been successfully demonstrated in a continuous pilot plant processing 350 kg/d of nodule ore. The chemistry, basic flowsheet and operating characteristics are presented and discussed.

Jan 1, 1980

By Karl L. Konnerth

THE rapidly increasing use of machinery for the mining of coal and operations incidental thereto has materially changed conditions from a safety standpoint. A few of the coal-producing states have recognized the need for specialized electrical equipment for use in mines and have introduced certain requirements in their State safety regulations, notably Pennsylvania. This paper discusses the principal problems involved in maintenance of such equipment. PERMISSIBLE: EQUIPMENT "Permissible" electrical equipment is equipment that has met certain prescribed standards for use in mines where hazardous conditions may occur and has been recommended by the U. S. Bureau of Mines. Such machinery is available on the market for most coal-mining operations--for instance, coal cutting, transportation, drilling, loading, working-place illumination, shot-firing and pumping. A notable exception is the trolley-reel gathering locomotive which, although its parts may be explosion-tested by the Bureau, has not been approved as permissible for the following reasons: I. The trailing cable is subjected to more severe service than on other equipment. 2. State regulations do not require that a working place be examined for methane before a locomotive enters it. 3. Even with two-conductor cable, imperfect or inadequate bonding may cause the emission of sparks at the wheels of the locomotive and at rail joints. 4. As the locomotive is equipped with a trolley pole, and as the trolley wire may be installed and used in unsafe territory in spite of rigid State regulations, a trolley-reel gathering locomotive is always a potential hazard. MAINTENANCE The proper procedure for maintenance of permissible equipment may be divided into three parts: (I) inspection, (2) actual maintenance and (3) changes or improvements to existing machines. To secure the fullest benefits through the use of permissible equipment it is necessary that all men involved understand the principles underlying the safety features of this equipment and realize the significance of defects, so that neglect and indifference in the maintenance thereof may be eliminated. Inspection From the standpoint of safety it is desirable no doubt to make a suitable inspection of permissible electrical equipment once a week, but the opening of every enclosed compartment at each inspection may do more harm than good. The openings to such compartments are closed with various types of covers very accurately machined, often made of the softer alloys to reduce weight, and fastened with a multitude of bolts, screws, washers, and other small parts. Frequent handling of these covers may cause sufficient damage to defeat their original purpose and intent.

Jan 1, 1941

By Lauren A. Wright, A. E. J. Engel

Under the designations "industrial talc" and "soapstone" are included earth materials of widely different chemical and mineral compositions. Talc, the mineral, is a hydrous magnesium silicate, with a suggested theoretical formula H2Mg3(SiO3)4 or H2O.3MgO.4SiO2, which postulates 63.5 pct SiO2, 31.7 pct MgO, and 4.8 pct H20.18 Single grains or leaves of talc, however, seem to have variations in water content that range from 3.5 pct to more than 7 pct, as well as slight differences in the proportions of MgO and Si02.20 Most of the industrial talcs produced in the United States do not approach the composition given above (see Table 1), but are essen- [ ]

Jan 1, 1960

By W. H. Ode, W. A. Selvig

By plotting fixed carbon against British thermal units of coals free from mineral matter, and ranging in rank from anthracite to lignite, it is found that the coals of higher rank, from anthracite to the higher rank of the high-volatile bituminous coals, inclusive, can be separated into groups according to their degree of metamorphism by reference to their fixed carbon. Such charts show also that the coals lower in rank can be best separated into groups with respect to B.t.u., especially when plotted on the moist basis, that is, coal containing its natural bed moisture. A tentative scheme for coal classification was presented at the October, 1932, meeting of the Technical Committee on Scientific Classification, of the American Standards Association Sectional Committee on Coal Classification. This scheme was sponsored by Subcommittee IV on Tentative Classification of Coals, under the chairmanship of W. T. Thom, Jr. It proposed the grouping of coals according to rank by reference to fixed carbon and B.t.u., on the basis of coal containing its natural bed moisture but free from mineral matter. This scheme proposed classifying coals into four broad classes: (1) anthracitic, (2) bituminous, (3) subbituminous, (4) lignitic. The anthracitic class was divided into three groups designated as meta-anthracite, normal anthracite, and semianthracite. The bituminous class also was divided into three groups, low volatile, medium volatile, and high volatile. The high-volatile group was further subdivided into four subgroups according to moisture content, as fo1lows: (1) less than 5 per cent, (2) 5 to 10 per cent, (3) 10 to 15 per cent, and (4) 15 per cent and more. The subbituminous class was divided into two groups, group 1 including subbituminous coals having calorific values of 10,500 B.t.u. or more, and group 2 including those with less than 10,500 B.t.u. The lignitic class of coal was divided into two groups both below 8,000 B.t.u., the one group consisting of consolidated and the other of unconsolidated

Jan 1, 1934

By Zhu Weishen, Xu Dongjun

In the 1st part of this paper a comparassion of the different methods for determining the modules of elasticity and deformation of hard rock is made. It is found that the plate bearing method has a serious shortcoming. The slit flat-jack method seems to be a mare reasonable technique, which is recommended as a desirable method for in situ testing. In the 2nd part, a new test method to determine the properties of deformation and strength of weak plane in rock mass is recommended. Then the relation of weak plane character to the character of stress-strain curve, the relation of normal stress to the character of shear displacement curve and the yielding criterion of weak plane are discussed.

Jan 1, 1982

By Clarence P. Linville

A previous article1 by the authors contained a general description of the new roasting furnace herein described but it did not go into detail as to the metallurgical behavior or the results obtained. Believing that such information would be of great value, they have elaborated on the subject and have given many unpublished details. The furnace described applies the principle of roasting finely divided zinc-sulfide ores, now produced in large quantity by the flotation process, in gaseous suspension; that is, the ore particles are carried, in suspension, in a current of air and gaseous products of the roast. The relatively great fineness of flotation concentrate presents difficulties and problems of roasting in furnaces of the ordinary type; the fine ore is forwarded through the furnace in the form of a shallow bed and its very fineness leads to dense impervious bedding which prevents oxygen from reaching the interior of the bed, thus unduly lengthening the time of roasting and preventing the elimination of the last of the sulfur. The fineness of the concentrate, normally, should lead to a rapid and complete roast, for the speed of roasting is a function of the surface exposed to oxygen, which surface is greatest, per unit of weight, in very fine material. The difficulty in bed roasting is to get the oxygen to the particle. If the fine ore, during the roasting, could be freely suspended in oxidizing gases, full advantage could be taken of the great surface conferred by its fineness. This fundamental idea, of course, is not new, for the Stedtefelt furnace, familiar to the older metallurgists, is an example of it; but the manner in which this is accomplished may be new. The numerous efforts to roast in gaseous suspension show that the idea is attractive; in fact, an analysis would indicate that it is the most reason-

Jan 1, 1925

By J. F. Blandy

In October last, I was call upon to examine a copper deposit in the South Mountain, near the Pennsylvania and Maryland boundary. The specimens shown me contained oxides and carbonates with native copper, and were similar to some that had been described to me some years ago as existing at the Luray Gap in Virginia. An examination of Rogers's Report on the Geology of Pennsylvania, led me to expect to see his so-called "Primal Formation," such as exists throughout the southeastern district of the State. I was therefore much surprised on arriving at the summit of the Western Maryland Railroad to find myself on familiar ground. Instead of the "Primal" as I had known it in Southeastern Pennsylvania, I soon decided that the rocks were identical with the ('Lake Superior Copper Formation." My visit was unfortunately a short one, —part of two days, and in that time I had to pass over a good many miles,—but I saw sufficient to convince me that instead of the Lake Superior Copper Formation being a local geological feature, it would have to be considered as a widely extended series of rocks. I was unable to even approximately estimate the thickness either of the trap zone or other members, schists and slates, of the series. In an article on the Copper 'Range of Michigan, prepared by C. P. Williams and myself in 1862, and published. in vol. xxxiv of the American Journal of Arts and Sciences, we endeavored to divide that range into zones, according to the character of the traps. The limited nature of the explorations at that time made this work very imperfect. Subsequent explorations have confirmed my notes then

Jan 1, 1879

By Thomas H. Leggett

In speaking of the mining and economic conditions prevailing at the present time on the Rand, it is not my intention to go into the details of the mining practice, since this has been already well described both in the Transactions' and elsewhere,2 but rather to take a more comprehensive view of the industry and its surroundings as a whole, marking its general development and the lines of its future progress. In a paper entitled Deep-Level Shafts on the Witwaters-rand, with Remarks on a Method of Working the Greatest Number of Deep-Level Mines with the Fewest Possible Shafts,' presented to this Institute in August, 1900, I drew attention to the great cost of sinking the very deep vertical shafts that were then being seriously proposed as necessary for the development of the deeper areas, pointing out the strong advisability of working this ground by means of inclines to be sunk from the existing shafts of from 3,000 to 4,000 ft. in vertical depth. In this paper it is stated (p. 975): '" In short, practice upon the Rand now tends towards fewer vertical shafts and more underground inclines, especially for the very deep mining about to be undertaken." In consequence, the 6,000-ft. vertical shafts, at one time so much discuesed, have never been started, and they do not now seem likely ever to be. The necessity of placing all deep shafts further apart in order to make them control and exhaust larger areas was also dwelt upon. This economy wae vitally necessary for both

Jan 1, 1909

By Howard S. Bryant

The state of Kansas in 1931 continued to hold fourth place on the list of oil-producing states, despite the fact that low prices for crude oil curtailed drilling to just one-half the amount done in 1930, which itself was the lowest in the preceding 10 years. The estimated crude oil production for 1931, according to sources available to the writer, will approximate 37,037,000 bbl., the lowest since 1925. Thus Kansas produced one-eighth less oil this year than it did last year when it produced 42,729,085 barrels. This year's development was characterized by a very small amount of wildcat drilling; however, large new areas were semiproven for oil production, and several thousands of acres were added to the actually proved areas in western Kansas, so that the state now has larger proven areas of oil reserves than at any time in its history since the heyday of the famous El Dorado pool. The general prospects for oil production in the near future are indeed promising for central western Kansas, where drilling costs are moderate and depths are relatively shallow compared to the remaining unexplored parts of the northern Mid-Continent area. Probably the greatest singular achievement in the state for 1931 was the development of its natural gas reserves. This development took place principally in two spots, McPherson County in central Kansas, and Stevens and Morton counties in southwestern Kansas, and it is a matter of record that more than one and one-half billion cubic feet of open-flow capacity per day were added to reserves, nearly twice the amount developed in 1930, previously the largest amount in the history of gas development in Kansas. Gas pipe lines already built and now building are in position to deliver natural gas by one system to Chicago, Ill., by another to Indianapolis, Ind., from whence lines already lead practically to the Atlantic seaboard, and to other cities large and small located west, northwest, north and northeast of Kansas. Table 2 shows all well completions for 1931 in a form to compare with the results of previous years.

Jan 1, 1932

By Olav Dalen

A HUNDRED years have passed since Wöhler made the first few particles of aluminum by decompos-ing aluminum chloride with potassium. In 1854 Deville used sodium to decompose the double chloride of aluminum and sodium, but even various subsequent improvements of the process, especially by Castner, did not sufficiently decrease the cost of the metal to bring it into general use. In 1862 Monckton proposed to reduce Al O? with carbon by the aid of the electric current, but the efforts of the Cowles brothers to do so were not successful and in 1884 they turned to making aluminum alloys by electrolysis. At about the same time Hall in America and Heroult in France success-fully worked out the technology of dissolving A12O3 in fused cryolite and electrolyzing the bath. It is hard to realize that forty years ago the annual production of aluminum was only 30 to 40 tons per year and the price of the metal thirty times what it is today. Great strides in decreasing the cost of production, improving the quality of the metal, and increasing the output have been made in the lifetime of middle-aged men. The large consumption of electrical energy in the form of direct current makes it necessary to locate aluminum-producing plants near waterfalls, to avoid transmission losses. Norway with its abundant water-falls is therefore a logical place for the development of aluminum production, even though it is necessary to import the bauxite, which is the raw material of the process. It was foreigners who first started the aluminum in-dustry of Norway and the first two plants were built by the British Aluminium Co. in 1906 to 1908; one at Vigeland near Kristiansand, and the other at Stavan-gerfjord in Nordfjord. These two plants are still oper-ating and producing over 3000 tons a year. When the plant at Vigeland is enlarged the production of the company will be more than 4000 tons a year.

Jan 11, 1927

I HAVE striven to demonstrate to you as well as possible the method of bringing the metals of your ores to their ultimate perfection. But one cannot always do with gold that is found in the ores what is done with the other metals, for gold is not always accompanied by fine silver nor is it

Jan 1, 1942

By K. D. McBean, W. H. Hannay, B. A. Stimmel

The electrolytic plant at Trail, B. C., was erected by the Consolidated Mining and Smelting Company of Canada, Ltd., for the treatment of zinc ores and concentrates, particularly those of the Sullivan mine at Kimberley, B. C. It began operations in 1916 at a rated capacity of 60 tons of cathodes per day, which has been steadily increased to the present production of 400 tons per day. The Sullivan has furnished the greater part of the zinc so far produced, although notable tonnages of customs zinc concentrates have been treated. The maximum yearly tonnage of customs concentrates, 25,000 tons, was treated in 1926. Practically no customs concentrates hale been treated since 1929. The total bar zinc production to the close of 1935 was 1,092,782 tons. The zinc mineral in the Sullivan ore is marmatite of somewhat variable composition, ranging between 6ZnS.FeS and 8 ZnS.FeS. Practically all the zinc ores tributary to this plant are marmatites; and the iron content of the zinc mineral varies considerably. The formation of zinc ferrite during roasting is now a matter of common knowledge, so the possible extraction from any zinc concentrate is largely a function of the iron content; the progress made in concentration is reflected directly in zinc-plant recovery. The Trail plant operafes on the low-acid system, as do all the other major plants on this continent at present operating, except the electrolytic plant of the Sullivan Mining Co. at Kellogg, Idaho. The new Magdeburg plant, in Germany, occupies an intermediate position between high and low acid. Plant operation at Trail will be treated in this paper under five main sections: roasting, leaching and purification, electrolysis, cadmium recovery and melting. The oxide section of the plant, treating zinc fume from re-treatment of lead blast-furnace slag, is practically a separate zinc plant; this is necessary because of the presence of fluorine in the smelter zinc fume. Cadmium is recovered electrolytically from the purification residues of both the sulphide and oxide leaching plants.

Jan 1, 1937

Jan 1, 1949

By Jerry A. Selvaggi, Richard B. Jacob

The High Gradient Magnetic Separator (HGMS), also known as the High Gradient Magnetic Filter (HGMF), is an effective device utilized in magnetic separation. This method of separation is gaining popularity in the separation of submicron material containing feebly magnetics. The most common use of this type of separator is in the removal of iron stained particles to improve the brightness of kaolin clay. Potential areas for use of this magnet include: (1) desulfurization of coal (2) the clean-up of mill effluent (3) removal of fine particulate matter from municipal and indus¬trial waste (4) desulfurization of oil Design, operation, and applications of this separator are further dis¬cussed in papers by R. R. Oder (1975), and R. R. Oder and B. I. Horst (1975). This device is a system composed of an iron enclosure of high per¬mability material housing a set of electrical coils, a canister en¬closing a magnetic matrix (stainless steel wool), an electric power supply and a hydraulic system to maintain specified operating tempera¬ture conditions. See Figure 1.

Jan 1, 1984