Search Documents

By John L. Schroder

In selecting the best system of mining for a particular operation, many different factors must be considered. The system to be finally selected should be that which provides: 1) The highest possible degree of safety for mine personnel. 2) The lowest cost per ton of product. 3) The maximum coal production per man-shift. 4) The most suitable quality of final product, considering its intended use. 5) The maximum percent recovery of coal per acre of reserve consistent with cost and subsidence rights. 6) Consideration for the ecology of the area. Some of the important factors to be considered when choosing a method of mining are: 1) Amount of cover over the coal seam. 2) Type of the rock in the overburden. 3) Characteristics of the coal seam including: (a) the thickness of the coal seam; (b) the nature and location of any impurities or irregularities; (e) the dip (or pitch) of the coal seam; (d) the nature and direction of any definite cleavage ill the czoa1 seam; (e) the hardness of the coal; (f) the structural strength of the coal; and (g) the presence, anti amount, of explosive gas (methane). 4) Quantity of water likely to be encountered in the mining operation. 5) Nature and strength of the roof (top) over the coal seam. 6) Nature and strength of the floor (bottom) under the coal seam. 7) Any previous or concurrent mining in seams above or below the coal seam to be worked. Information on items 1-7 may be obtained in several ways. Topographical and geological reports and maps of the area are generally available

Jan 1, 1973

By Cleland N. Conwell

Reclaiming mined land in northern regions is less difficult than reclaiming semiarid lands. In 1972, the Usibelli coal mine near Healy, Alaska, initiated experimental plots to determine the proper grasses and amounts of fertilizer. The following spring, approximately 1600 acres of land disturbed by mining were seeded by low-flying aircraft. The reclamation project was evaluated by the State of Alaska and has been adjudged successful. The information gained is being used in reviewing prospecting permits and granting coal leases on state lands.

Jan 1, 1977

PROF RICHARD ÅKERMAN Stockholm, Sweden DR FRANK DAWSON ADAMS Montreal, Canada ANDREW CARNEGIR New York, N.Y. PROF HATON DE LA GOUPILLIERE Paris, France SIR ROBERT A. HADFEILD London, England HERBERT C. HOOVER Leoben, Austria JAMES FURMAN KEMP New York, N.Y. PROF HENRI LOUIS LE CHATELIER Paris France EZEQUIEL ORDONEZ Mexico City, Mexico ALEXANDRE, POURCEL Paris, France PROF RICHARD H, RICHARDS Boston Mass. JOHN E. STEAD Middlesborugh, England PROF DIMITRY CONSTANTIN TSCHERNOFF St Petersburg, Russia PROF TSUNASHIRO WADA Tokyo, Japan CHARLES D WALCOT Washingtion D.C.

Jan 1, 1923

For the year ending February, 1917 PRESIDENT L. D. RICKETTS,1. NEW YORK, N. Y. PAST PRESIDENTS BENJAMIN B. THAYER,1 NEW YORK, N. Y. WILLIAM L. SAUNDERS,2 : NEW YORK, N.Y. FIRST VICE-PRESIDENT SIDNEY J. JENNINGS,1 NEW YORK, N. Y. TREASURER GEORGE C. STONE,1 . NEW YORK, N.Y. SECRETARY EMERITUS ROSSITER W. RAYMOND, NEW YORK,. N. Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N.Y.

Jan 1, 1917

Fred D. DeVaney (Magnetic Roasting of Iron Ores, P. 1219) has presented several other AIME papers, all of them concerned with grinding and concentrating problems. He is chief metallurgist, Pickands Mather & Co., at Hibbing Minn., after working for the U. S. Bureau of Mines at Tuscaloosa, Ala., and Rolla, Mo., as a junior metallurgist and a metallurgist. DeVaney started as a research metallurgist with Pickands Mather in 1942. He set up the first laboratory in the Lake Superior district devoted to taconite concentra¬ [ ] tion, his major interest. He has been an AIME member since 1923, holding various offices, including the first presidency of the Minnesota Section. DeVaney has a Bachelor's in Mining, and Master of Science earned at the University of Alabama in 1924. He is a member of the Engineers Club of Northern Minnesota and plays golf for relaxation and enjoyment.

Jan 1, 1952

By Rodney P. Smith

The rate of motion of the boundary between a single-phase a-iron region and a two phase a-iron plus ?-iron, or a-iron plus cementite region has been measured on decarburization at several temperatures between 500" and 865°C. These data, together with data for the carbon content of a-iron at the boundary, yield the diffusivity of carbon in a-iron. The activation energy for carbon diffusion is 19.8 kcal per mole for the temperature range —50° to 150°C and increases to an average value of 23.0 kcaL per mole for the temperature range 727" to 865°C. AS part of an investigation of the diffusivity of carbon in iron using a steady-state method,' the diffusivity of carbon in a-iron was determined at the temperatures 802" and 851°C. The diffusion constant thus obtained was larger, by nearly a factor of two, than that predicted from the combined results of stanley2 and of Wert.3 It seemed desirable, therefore, to continue the investigation. Since the temperature range in which the steady-state method can be conveniently used is limited, we have chosen a decarburization method, based on the laws of diffusion in metal accompanied by a phase change.4,5 If the initial carbon content of the Fe-C alloy is such that two phases coexist at the decar-burizing temperature* and decarburization is car- ried out such that the surface is maintained at substantially zero wt pct. C, the carbon distribution after a time, t, will be as shown in Fig. 1. The boundary between the single-phase and two-phase regions moves from y = 0 to y = x in the time, t, where x is proportional4 to tl". If the initial carbon (content of the sample is Ci, and CB is

Jan 1, 1962

By J. P. Hirth, G. M. Pound

The flux of evaporation J from {loo) , {111), and (110) planes of silver single crystals and from poly crystalline specimens was measured at 744°C under a high vacuum using a time average weight loss method. The evaporation coefficient a was computed from the measured flux and vapor pressure data through the relationship J = aPe/21rmkT. The evaporation coefficients for the close packed planes and the poly crystalline specimens were found to be about 0.4 providing tentative confirmation of the theoretical limiting law for evaporation of metal crystals, a = 73(P/Pe) + % . The (110) planes faceted to form (111) planes, resulting in a greater evaporating area and larger a . The evaporation morphology of the plane surfaces and the surfaces of spherical single crystals is described in some detail. RECENTLY a detailed theoretical analysis of the mechanism and kinetics of metal crystal evaporation was made.1'2 A mechanism for vaporization involving the recession of monatomic ledges across a metal surface was deduced, and evaporation rate equations were derived by considering the dynamics of these ledges. In most metals, the process of evaporation is one of dissociation of atoms from ledges, surface diffusion, and desorption. The gross vaporization rate is controlled by the surface diffusion and desorption rates. It was shown that the monatomic ledges, under the action of surface diffusion gradients, tend to assume a terminal velocity and spacing. Further, it was shown that crystal edges and grain boundaries are a ready source for monatomic ledges. In the case of evaporation of large, perfect crystals with clean, low-index surfaces, the kinetic treatment1 leads to a limiting law for crystal evaporation: where J is the gross flux of vaporization, a is the evaporation coefficient, Pe the equilibrium vapor pressure, m the atomic mass, k Boltzmann's constant, T the absolute temperature, and P the actual pressure of vapor over the crystal surface. Imperfections such as grain boundaries, pores, cracks, and macroscopic steps should have the effect of causing positive departures from this limiting law. Such an imperfection is a source for monatomic ledges, which, near their origin, are closely spaced and thus give rise to higher evaporation rates there. However, under many experimental conditions,' this effect should be negligible due to the relatively low concentration of imperfections. In general, a more important cause of positive departure should be screw dislocations, and the effect of these has been considered in some detai1.2,3 Monatomic ledges emanate from points where the surface is intersected by a dislocation with a screw component normal to the surface. The dynamics of ledges arising from a screw dislocation are similar to those of ledges arising from a crystal edge. There is a perturbed region near the origin where the monatomic ledges are, under certain experimental conditions, closely spaced and the

Jan 1, 1960

FOLLOWING the presentation at the annual meet-ing of the paper "Recent Developments in Classi-fication," by A. M. Gaudin and W. L. Remick, the discussion presented below took place: H. N. Spicer : I haven't been able to study this paper closely, but I would like to ask 'Mr. Remick something regarding the work done by the mechanical classifier. The screen test given here would appear to show that the classi-fier did very, very poor work. The 44 per cent efficiency calculated from this equation is much lower than any ordinary operation. Nothing is stated regarding the de-tails. of the operation, the slope of the classifier, the dilu-tion, the speed, and such other factors that influence results. I would also like to know something of the material that was worked. The Manhattan schist that I have seen them digging out of the subways is of a flaky nature, so that in any classifier, you might get the factor of fine flakes floating over. Was the same material used in the hydrotator test? The screen tests vary a whole lot. Mr. Remick: You will notice the Dorr classifier han-dled the circulating load. This classifier naturally was run in closed circuit. I should like to be pardoned for quoting from Mr. Bates' paper of last year on "Classifica-tion in the Witwatersrand Mills." In this report only two efficiencies were given for the so-called straight type Dorr classifier. One was 44.6 per cent and the other 61.6. I don't know whether or not an average should be taken for the proper performance. I assume that that test was performed under better conditions, yet the efficiencies av-eraged only 53.1 per cent. I am afraid I am taking the words out of Professor Taggart's mouth, but he has told me that the Dorr classi-fier at Columbia is not the proper size to work with the Hardinge mill with which it is connected. This indicates only the inadvisability of putting commercial sized mat chines in a school laboratory. You cannot, he says, get the proper tonnage from the Hardinge mill to work the Dorr classifier and get the best results. Mr. Bates' results show higher efficiency with the lower capacity. Now, on the other hand, I assume that the classifier described in Mr. Bates' paper was probably run at the proper capacity.. It is a rather puzzling question.

Jan 4, 1927

By Robert I. Jaffee, Walter L. Finlay

IN the broad survey of the nonferrous' metallic elements contained in this book, the reader may well be impressed by the wide range of property combinations offered by the many metals and alloys the metallurgist has prepared since before Kubla Khan. The diversity is great and the overlap is considerable. It is particularly surprising, then, to find the latest structural metal new- comer designated by such extravagant terms as "Cinderella Metal," "Wonder Metal," "Miracle Metal," "The Metal of Tomorrow," "Dream Metal or Nightmare?" and "The Middleweight Champion of the Structural Metals." Of these and others, the most appropriate designation for the metal involved, titanium, appears to be that of The Middleweight Champion. Its intermediate density of 4.5 and elastic modulus of 16 million is a unique combination between the lower density and modulus of magnesium and aluminum and the higher density and modulus of copper, nickel, and iron. It is light, strong, ductile, and corrosion resistant. A chemical neighbor in group IV of the Periodic Table, zirconium, is similar to titanium in many respects but is appreciably denser, 6.5 instead of 4.5, less stiff and relatively much less abundant. On the other hand, the resistance of zirconium to acids and alkalies is better than that of titanium. Also, compensating for its higher density, lower stiffness, and somewhat lower strength level compared with titanium, zirconium has much better permeability to slow neutrons and is much more suitable as a material of construction for nuclear reactors.

Jan 1, 1953

By H. G. Turner

The coals mined in the area known as the anthracite fields of Pennsylvania have always been recognized commercially as anthracites. In the literature, however, some of these anthracites have been called semi-anthracites by various writers. The coals mined in Sullivan County, especially those from the Bernice field, have been recognized commercially both as anthracites and semi-anthracites. In the literature they have almost always been referred to as typical semianthracites, although Franklin Platt,1 in his report to the Pennsylvania Geological Survey, uses the terms semibituminous, semianthracite, and anthracite in describing them. The purpose of this paper is to endeavor to dispel the confusion of names used to describe these coals and to supply further information that will permit a logical and definite classification. Most of the confusion of the past has been due to the impossibility of securing enough fresh face samples from which to draw sound conclusions; some of it was due, no doubt, to lack of standard methods of analysis, and of course, to the ever-present lack of definition of boundaries from the standpoint of classification. Map Showing Lines of Equal Volatile Matter and Lines of Equal Specific Gravity As a foundation for this work the writer constructed a map showing lines of equal volatile matter and lines of equal specific gravity throughout the anthracite and semianthracite regions. The points on these lines were determined from a study of analyses of 214 face samples from 28 mines and composite analyses from 18 different breakers. These samples were collected through the joint efforts of the U. S. Bureau of Mines and the Anthracite Institute. The Bureau of Mines standard method of sampling was used in all cases. All analyses were made by the Bureau of Mines and are used here with its permission. The

Jan 1, 1934

By R. G. Ward, P. L. Sachdev

Using an improved maximum bubble pressure technique, the densities of iron silicates at 1400°C have been measured under nitrogen. At the wiistite composition the density has been measured by bubble-blowing experments with both argon and nitrogen and calculated from the measured volume of a known mass of melt under nitrogen. The densities under nitrogen are significantly different from those measured under argon for melts containing less than 28 wt pct SiO2. THE constitution of liquid slags is not well understood, largely because no single property or parameter can be measured which gives conclusive evi- dence of the types and packing of the ions present. Of the many property measurements which can provide information leading to a picture of the constitution of slags, density gives the most direct evidence and has been studied extensively. The work reported here is part of a program of study of densities in multicomponent melts in which the iron oxide-silica system is the solvent. These melts are important as they are fundamental to basic steelmaking, and they allow the study of basic silicate compositions which have hitherto been largely neglected. As considerable disparity exists

Jan 1, 1965

By J. J. Kramer, G. W. Wiener, K. Foster

The effects of the primary grain size and sheet thickness on the secondary growth rates of grains with (100) surface planes were studied in 3 pct Si-Fe sheets. This secondary grain growth was carried out under conditions in which the {100} plane had the lowest surface free energy. The value of the surface energy difference, between the (100) plane and the random matrix planes was found to he only about 3 pct of the grain boundary energy, indicating that most of the driving force for secondary growth is supplzed by grain boundary energy. A method for obtaining cube texture in 3 pct Si-Fe sheets by a secondary recrystallization process has been reported.' It has been demonstrated that a difference in surface free energy between the (100) plane and other planes is responsible for this growth, where the (100) plane has the lowest surface energy. A semiquantitative relation has been derived for secondary grain growth in sheets where primary grain growth has proceeded until the grains have grown through the sheet and the average grain diameter in the plane of the sheet is from one to two times the sheet thickness. Then, the linear growth rate, G, for the secondary grains can be given by where M is the grain boundary mobility, is the grain boundary free energy, is the average primary grain radius, A is the average difference in surface free energy between the (100) plane and planes of other orientations, t is the sheet thickness, and C is a term first proposed by zener6 which acts as a negative driving force, the effect of inclusions in holding up grain boundary motion. Since the problem of grain growth being discussed is under conditions where the matrix grain size is at least equal to the sheet thickness, the radius r is, of course, a function of the sheet thickness. The term B/r is the grain boundary driving force normally associated with inclusion inhibited or texture inhibited secondary recrystallization. Here, however, the term is modified to account for the fact that growth occurs in thin sheets. The term is the additional driving force available because of the difference in surface free energy. The purpose of the present work has been to evaluate the driving force terms of the growth equation by studying growth rates of (100) secondary grains as a function of sheet thickness and primary grain size. From these data it has been possible to determine the relative values of grain boundary energy, surface energy difference, and the inclusion term, C. EXPERIMENTAL PROCEDURE A 3 pct Si-Fe alloy was melted and cast under a helium atmosphere using electrolytic iron and a pure commercial grade of silicon as raw materials. The alloy was hot and cold rolled to a thickness of 0.6 mm, and samples approximately 5 in. long by 1 1/4 in. wide were cut from the cold-rolled sheets. Four different primary grain sizes were obtained

Jan 1, 1963

February 18th, 1873. THE Institute assembled in the Hall of the Boston Natural History Society on Tuesday evening. Dr. T. Sterry Hunt, of the Boston Institute of Technology, after a brief address of welcome to the Institute, read an introductory paper on the Geognostical History of the Metals. President Raymond responded to the welcome of Dr. Hunt. The following names were then presented to the Institute, with the recommendation of the Council, for election Adams, J. M., - Silver City, Idaho. Daggett, Ellsworth, - Salt Lake City, Utah. Geist, Alfred W., - Boston, Mass. Hays, Dr. S. Dana, - Boston, Mass. Heinrich, Oswald J., - Midlothian, Va. Johnson, J., - Braidwood, Ill. Leckie, Robert G., - Actonvale, Canada. Lyman, Edward, - Troy, N. Y. Maltby, William, - Braidwood, Ill. Nichols, Lyman, Jr., - Boston, Mass. Ordway, Prof. J. M., - Boston, Mass. Rand, Theodore D., - Philadelphia, Pa. Richards, Prof. Robert H., - Boston, Mass. Rockwell, Prof. Alfred P., - Boston, Mass. Roepper, Charles W., - Bethlehem, Pa. Schulz, A. von, - Central City, Colorado. Singer, William F., - Pittsburgh, Pa. Spillsbury, E. G., - New York. Wells, Calvin, - Pittsburgh, Pa. The session concluded with the reading and discussion of a paper, by Henry Engelmann, On the Mines and Ores of the Little Cottonwood Canyon, Utah. The second session was held on Wednesday morning, when the following papers were presented; On the Midlothian Coal Mines, by Oswald J. Heinrich. On the Probable Existence of Microscopic Diamonds in California, by Prof. Benjamin Silliman.

Jan 1, 1873

By Michael J. Messel

THE critical shortage of asbestos fiber in the world today brings to the foreground the question of locating and developing new deposits. The object of this paper is to discuss some of the more important factors which should be considered in the examination and valuation of a new asbestos enterprise. Some of the more important uses of asbestos fiber are for textiles, heat insulators, building materials, filters and a series of other uses. The properties of this mineral, such as fibrous structure, color, strength, silkiness and flexibility, coupled with resistance to fire, certain chemical action and decay make its application unique for certain industrial uses which consume over 500,000 tons annually. These same unique properties which make this mineral so valuable also make a deposit one of the most difficult to appraise accurately, because of the many undeterminable and varying factors which must be considered before a deposit can properly be termed commercial. The majority of the asbestos fiber today, having the above mentioned properties, is sold by grades which are based on fiber length. Present day fiber prices vary over a wide range from $800 to $225 for crude fibers and $300 to $20.00 per ton for milled grades. For valuation purposes a careful study should be made of existing fiber prices and markets. EXAMINATION OF DEPOSITS In carrying out prospecting and examination of a deposit, considerable caution is required to get the necessary information in the form that will have the most value for the final determination. There are two main classes of asbestos fibers, chrysotile and the amphiboles, the chrysotile being, by far, the most important both in abundance and uses. This paper will stress mainly chrysotile deposits, however, the amphiboles have many important uses, especially amosite and crocidalite. Their valuation presents special problems as other factors may be involved, especially as they are not graded according to any well defined and adopted standard but usually according to the use for which they are being supplied. Most chrysotile deposits occur in two main types of rock, (I) mainly in basic igneous, such as dunite and peridotite, (2) to a lesser extent in sedimentary rocks, such as dolomite and limestone. All of these require a certain degree of metamorphism to be favorable to asbestos formation. Approximately 90 pct of the asbestos deposits are derived from serpentinization of dunite or peridotite, whereby the magnesiumsilicate olivine was altered to hydrous magnesium-silicate serpentine. Under certain favorable geological conditions, this serpentine takes a fibrous form having a definite crystal structure, probably due to molecular rearrangement, and is known as chrysotile. The fiber veins are usually ir-

Jan 1, 1947

By Wm. Hamilton Merritt

IN this paper, which I have the honor to submit to the Institute, it is my intention to treat especially of that part of the North Staffordshire field which converges to a long tongue in the neighborhood of Congleton, and which includes the villages of New Chapel, Ford Green, Norton, Biddulph, Bradley Green, Gillow Heath, and the immediate vicinity. My object is not so much to give a minute description of the geology or systems of mining and smelting, as by a general review, some idea of the extraordinary facilities for the production of excellent iron, which have enabled this district to maintain its position more successfully than any of its rivals against the late depression in trade. The North Staffordshire coal field has the Cheshire and Lancashire fields some thirty-five miles to the north, those of Derbyshire and Nottinghamshire forty miles to the east, those of South Staffordshire and Shropshire, about thirty miles to the south, and the Denbighshire and Flintshire fields some forty miles to the west. It is highly probable that the coal continues under the new red sandstone to the Western and Southern fields as the dips on both sides, and absence of large faults, make it impossible to come to any other conclusion. In a section of this coal field, from Chatterly to Whitfield, thirty-two workable seams of coal are shown, of an aggregate thickness of 130 feet, varying from 2 feet 6 inches to 7 feet, and thirteen seams of ironstone, 24 feet, averaging from 2 to 4 feet. All of these seams have been minutely described in a paper by Mr. Charles J. Homer, read in 1875 before the British Iron and Steel Institute. In the northern part, to which I especially wish to direct your attention, the beds lie in a V-shaped basin, the underlying millstone grit and Yoredale rocks rising and forming escarpments on either side of the valley containing the coal. Throughout this district, at the outcrop of the coal, there are indications of old workings. A shaft 4 to 5 feet in diameter reaches the coal at about 14 yards from the surface, and from it the coal has

Jan 1, 1880

By B. Silliman

The experiments detailed by Dr. Hunt,* having demonstrated the fact that the copper contained in the "clay ore" of Jones's Mine, was rendered completely soluble in the bath of ferrous chloride, used in the Hunt and Douglas process, after heating in contact with carbonaceous matter in a close vessel, I set myself to devise a form of muffle furnace adapted to the treatment of large quantities of these and similar ores by a continuous process. The result is shown in the diagrams on Plate X, reduced from the working drawings, after which this furnace was built early in 1876, at Phœnixville, by the Chemical Copper Company on their works at this place. The peculiar character of this ore determined the form, dimensions, and position, with reference to charging and discharging of these muffles. The ore arrived from the mine with from 20 to 25 per cent. of moisture, and when dried at 21o F., or more slowly at lower temperature, it falls to a light incoherent powder, with occasional lumps of undecomposed rock. In this condition it is readily mingled with coal-dust or any like reducing agent, and requires no other preparation for the muffle than the use of the shovel, to mix it well with the reducing agent. As it is a remarkably good non-conductor of heat, it was obvious that the mass, to be heated through in a reasonable time, must not be too thick, while the weight of the mass must be sustained in a way to avoid undue strain upon the walls of the muffle. These walls must be as thin as practicable, to favor the more rapid transmission of heat, and must, therefore, be so constructed as to admit of being stayed on the sides at frequent intervals to resist the lateral thrust of the very mobile mass of pulverulent ore, which, for obvious reasons, must be charged at the top and drawn from the bottom of each chamber. These considerations led to the form adopted, viz., two vertical muffles, standing upon very strong bridge tiles, seen in longitudinal section, on the line E, F, and in plan in Fig. 3, on the same plane. (Plate X.) The vertical section of the muffle is seen in Fig. 4, drawn in the plane G, H, of the longitudinal section, Fig. 6, which is the key to all sections. The walls of the muffles are built of the best firebrick, very care-

Jan 1, 1884

By B. Etkin, A. A. Haasz

The Infrasizer Mk III, developed at the University of Toronto, is capable of sizing particles of a few pm to hundreds of pm according to particle terminal velocity, which is a function of particle density, size and shape. The factors limiting the performance of the Infrasizer Mk III have been presented and analyzed. It has been established theoretically and experimentally that the device has excellent potential as a laboratory instrument. The principle is applicable to a continuous production classifier, a prototype of which is now under development.

Jan 1, 1980

By H. E. Rowen

As high grade iron ore deposits dwindle and costs rise, sintering becomes more and more important. The steel industry is now faced with beneficiation problems once peculiar to nonferrous work. Succeeding articles describe recent advances in this field. Here is presented the first chapter of a history still being written. SINTERING, for the purpose of this discussion, is defined as the art of burning a solid fuel with 90 to 95 pct ash content. Considering problems of combustion involved in keeping a home furnace burning properly with 12 to 20 pct ash in the fuel, it is evident that combustion represented by the definition has to be right or nothing is going to happen. Our forefathers discovered that many ores containing metals essential to the steadily rising standards of living were associated with elements such as sulfur and arsenic, which had to be removed before refining. This they did by utilizing the solid fuels they had available-the sulfur or other readily combustible components-to create roasting heat. One of the early methods is demonstrated in an old woodcut of the roast heap, Fig. 2. Ore was broken into chunks, piled on an ignition layer of solid fuel-logs in this case-and then. ignited. The sulfide ores roasted as the sulfur burned out. As shown in the background, the countryside was rapidly denuded of all vegetation by the great quantities of SO2 and other liberated gases.

Jan 1, 1961

By R. Neilson Clark

THE discovery of a thin pay streak, yielding carbonates of copper, native silver, and perhaps chloride of silver, was made on the 9th of April, 1874, within the trachytic belt which forms part of the Sierra Mojada. The discoverer named it the Humboldt Mine. On the 2d of May, 1874, another discovery was made, in a northwest direction from the Humboldt, at about five hundred feet distant, this was named the Pocahontas Mine. After some exploration these two discoveries were proven to be on the same vein. To the southeast of the Humboldt a claim had already been taken up, called the Virginia; and to the northwest of the Pocahontas, one called the Southeast Leviathan. On these last two this same vein has been found and worked. This paper will therefore treat of the Humboldt-Pocahontas vein, as worked on these four claims, to wit: beginning at the northwest, the Southeast Leviathan, the Pocahontas, the Humboldt, and the Virginia claims. Since the spring of 1874, there has been sunk on this vein a total of twenty-seven hundred and fourteen feet of

Jan 1, 1879