Search Documents

By J. Gordon Parr, D. H. Polonis

IN a previous study of hypereutectoid Ti-Ni alloys' a substructure was observed in quenched powder specimens when the constitution was 100 pet retained ß body-centered-cubic phase. The alloy powders were quenched from 1000°C by a blast of helium gas and precautions already described were observed throughout the work, to minimize contamination. Ogden et al.2 have previously observed subboundaries in the ß phase of a Ti-Mn-N alloy; but this structure was attributed to nitrogen-rich a precipitation. The nitrogen content of the Ti-Ni alloys does not exceed 0.02 pet and the quenching rate was sufficiently rapid to suppress precipitation reactions. Since X-ray diffraction results have confirmed the absence of any second phase which might account for this phenomenon, it seems unlikely that this substructure is explicable in terms of nitrogen content. Fig. 1 shows the substructure in adjacent grains of 100 pet ß phase in a quenched 6 atomic pet Ni alloy. Fig. 2 shows adjacent ß grains in a similarly treated alloy; one grain contains marked intracrys-talline boundaries and the other is completely free from any substructure. The suberystals appear to have fairly regular shapes, suggesting a regular orientation relationship among them. Tempering the retained ß structure at temperatures below the eutectoid eliminates the substructure at an early stage of ß decomposition. At the present time it is possible only to guess at an explanation for this subboundary phenomenon, since very little work has been reported on substructures resulting from phase changes. It is believed that the present phenomenon is due to poly-gonization resulting from unrelieved stresses set up

Jan 1, 1957

By C. A. Kroetz, A. J. O’Neal

The Long Island Lighting Co. has operated an extensive monitoring system for over three years. Nearly 900,000 separate pieces of information have been recorded for a land area of some 600 sq miles, 15 miles north to south by 40 miles east to west. The data are composed of about a half million sulfur dioxide measurements at various locations, 290,000 of which were by the West-Gaeke method, about 160,000 pieces of weather data, and 220,000 measurements of sulfur dioxide as emitted from each of the power plant stacks on the system, all measured on an hourly basis and stored on computor cards and tapes. The computor has been programmed to collate stack emissions, weather information, and ground level sulfur dioxide measurements. The analysis shows that emissions from tall stacks do, indeed, contribute very little to ground level sulfur dioxide. For example, LILCO shows that its Northport plant contributes less than 2 ppb, hourly annual average. They also state that the plant converted to 100% natural gas or shut down, would reduce ground level sulfur dioxide by no more than 2 ppb.

Jan 1, 1973

By V. R. Garfias, A. C. Fernandez

Despite artificial curtailment in all the fields of Mexico during 1937, owing to strikes and other disturbances, the production of crude petroleum aggregated approximately 46,738,000 bbl., showing a substantial increase of about 5,571,000 bbl. over the preceding year. Most of this increase occurred in the Poza Rica area, where, although only two wells were completed during the year, production increased from 14,162,000 bbl. in 1936 to 18,634,000 in 1937. While production in the South fields (Golden Lane) remained practically stationary, the output in the heavy-oil district of the Northern fields showed an increase of 1,930,000 bbl., because production had been considerably curtailed during 1936. Production in the Isthmus of Tehuantepec decreased about 596,000 bbl., owing to labor disturbances. Crude run to stills in local refineries increased from 34,000,000 bbl. in 1936 to 36,650,000 in 1937. Exports of crude and refined products were approximately 22,700,000 bbl., or 500,000 bbl. less than in 1936. Domestic consumption, excluding ships bunkers, reached a total of 20,000,000 bbl., which shows a small increase of 200,000 bbl. over the. previous year. Domestic demand for gasoline is estimated at 3,400,000 bbl. for the year, which represents an increase of 500,000 bbl. over 1936. In all, 60 wells were completed in Mexico during 1937, as compared to 70 in 1936 and 74 in 1935. In proven areas 52 completions resulted in 25 producers and 27 failures. In the Northeastern area near the United States border, five gas wells were drilled, all of which were producers; one of them, in Camargo, came in with a daily production of 20,000,000 cu. ft. of gas. One well, resulting in a failure, was drilled in Las Uvas, Coahuila, and three wells were completed in Quebrache, to the southeast of the heavy-oil district, resulting in two small producers and one failure. TWO more wells drilled in San SebastiBn, east of the Golden Lane, were failures. Fields Northern Fields (Heavy-oil District).—A total of 11 producers and 22 failures was completed in the proven areas of the Northern fields, as compared to 16 producers and 25 failures in 1936. In the Altamira

Jan 1, 1938

By Newell G. Alford

With the workable area of coal prospected and known as to workability and quantity and sampled and tested for desired quality comes the determination of the projection and method of working. The best method will be the one supplying the greatest degree of safety, the most merchantable product, the minimum average cost per ton with the largest yield of recoverable coal. Based on coal elevations, taken at the bottom of the seam on all known outcrop exposures, prospect openings or drill holes, coal contours are made on the map to be used in developing the mining plan. The contour interval should be as close as available information will permit. For general utility in layout of mining, haulage, drainage and ventilation, a map scale of 400 ft. per in. is preferable. In mountainous sections, location of the main out- crop opening or hoisting shaft is often limited by the available railroad route and amount of land level enough for a plant site. In level country, where a tipple and hoisting shaft may be placed at will, choice of the plant site should depend on the minimum average underground haul for the total coal to be worked to the new

Jan 1, 1932

By C. E. Meissner

THE need for a practical method of deciding upon new alloy steel analyses to widen its markets was the problem facing the Chrome Steel Works at the beginning of 1927. In addition to determining the physical properties of the alloys under consideration, it was necessary to test their value in service. Small melts of steel in a crucible, from which test specimens could be made, were insufficient to determine more than physical properties, therefore actual castings and ingots had to be made before the products could be placed in service. Furthermore, to save further experimental work, it was desirable that these heats should be made on a "pilot" basis; that is, actually duplicating regular open-hearth furnace practice. Therefore a one-ton (2000-lb.) acid open-hearth furnace was built. FURNACE DESIGN There are no special features in the design of this furnace. Standard acid open-hearth practice is followed, with the reproportioning of the dimensions necessitated by its small size; notably, a considerably increased length in proportion to width in order to get proper flame propagation. After the first heat was made it was found that the checkers were insufficient. The checker chambers were increased in size and the checker openings were made much smaller. The furnace was started late in March, 1927, and made 65 heats. Experimental work was then stopped until the data accumulated could be worked up and summarized. The run was resumed in November and the furnace is still operating, having made at this writing 60 additional heats. For the last series of runs, there was some rebuilding of both the furnace itself and the checkers. Slag pockets were added. Fig. 1 shows details of construction; Fig. 2, the, general appearance. All designing was done by the operating and engineering staff. Construction materials were those available around the plant. The reversing valve is a standard butterfly type taken from an old furnace.

Jan 1, 1928

By Richard Dunmore

Tests of the MRDE firedamp prediction method have been carried out in a number of longwall districts with different conditions. The method itself and its development have been described previously At many test sites the prediction has been good, i.e. the calculated gas emission levels have agreed with measured values, averaged over a period of many weeks, within a few percent. In other cases, where there have been larger discrepancies between calculation and measurement, investigations have shown that these may be attributed to particular conditions of mining or geology. Recognition of these conditions in advance of mining is clearly desirable to improve the accuracy of the initial prediction. It has been shown that variations in gas emission rates depend largely on coal production in terms of the weekly advance of the coal face. Although there appears to be a random element present, variations in gas emission levels calculated from changing face advances agree well with measurement. The accuracy of prediction therefore depends on how well face advance can be forecast and needs to be updated as the working proceeds in the light of the face performance actually achieved. Continuous monitoring of the mine environment provides the information necessary to compare actual gas emission with predicted levels, and computerised systems make it possible to carry this out in real time. Predictions can thus be adjusted to take account of emission levels measured in previous weeks These adjustments, whether they are made after the first few weeks or subsequently during the district life, would also be used to alert management to particular abnormalities or significant changes in gas emission.

Jan 1, 1982

By R. E. Maringer, A. Schwope

IT has been recognized that oxygen in minute quantities is extremely detrimental to the room-temperature ductility of molybdenum. Early fracto-graphic studies' of the cast metal indicated that oxides are formed preferentially at the grain boundaries. Additional verification of this preferential segregation has been obtained from internal friction studies on poly crystalline molybdenum (average grain diameter varied from 0.039 to 0.065 mm) and from observations of the effect of oxygen on specimens of extremely large grain size. Specimens A, B, and C, of 0.040 in. diameter commercial molybdenum wire (Lot FW 13-40) were heat treated in the vacuum furnace described by Few and Manning according to the specifications given in Table I. Internal friction studies of these specimens were carried out using a low frequency (approximately 1 cycle per second) torsional pendulum completely enclosed in a vacuum tank. As the pressure of oxygen in the heat treating atmosphere changed, the portion of the internal friction vs temperature curves ascribed to grain boundary relaxation changed correspondingly, Fig. 1. The decrease in the damping capacity at high temperatures as the pressure of oxygen in the heat treating atmos-

Jan 1, 1955

[ ]

Jan 1, 1942

Jan 1, 1879

By Thomas D. West

The fact that iron expands when heated, until fusion takes place, and that molten iron is consequently less dense than solid iron of the same grade, is now universally admitted. It was proved by the extensive experiments of Mr. Thomas Wrightson, reported in the Jownal of the Iron and Steel Institute (1890, No. 1, p. 72, and 1891, No. 1, pp. 75, log), and, in a manner, is illustrated in heavy founding by the shrinkage 'of the molten metal, which must be " fed " in order to obtain solid castings. This decrease in volume requiring " feeding" while the metal is still liquid I call " shrinkage," applying the term " contraction" to the decrease in volume which takes place after solidification, while the iron is cooling to atmospheric temperature. The light-work founder, not having the opportunity to make heavy castings, in which shrinkage can be observed, is apt to confound the two; but they are in fact distinct, and are separated by an act of expanion, which takes place at the moment of solidification. The fact of this expansion was first practically demonstrated by Mr. John R. Whitney, of Philadelphia, Pa., whose experiments are recorded in the National Car and Locomotive Builder of May, 1889. Experiments recently made by the writer indicate that there is a constant relation between this expansion and the preceding shrinkage and forcibly demonstrate the necessity of " feeding " a casting to make its interior solid. This is a matter with which all makers and users of castings have experienced difficulty. The founder being heretofore unable to define correctly the principles involving the urgent necessity of " feeding " has failed to impress the moulder with its importance in making sound castings.

Jan 1, 1897

By L. O. Brockway, W. C. Bigelow, J. A. Amy

Specimens of Inconel-X alloy solution-treated at 2050°F and aged for periods of 1, 10, 100, and 1000 hr at 1200°, 1400°, and 1600°F have been examined by electron microscopy and by electron and X-ray diffraction. Four minor phases were identified: titanium nitride, niobium nitride, an M23C6 complex carbide, and the intermetallic ? phase. The two nitrides were found in all of the aged specimens and in the solution-treated alloy, the y' phase formed at all aging temperatures, while the M23C6 carbide formed only on aging at 1200° and 1400°F. Variations in the hardness, rupture strength, creep strength, and yield strength of the alloy have been shown to be related to variation in the size and distribution of the particles of the y' phase within the matrix grains of the alloy, with maximum values of these properties occurring when there is a maximum amount of the phase present and a fine state of dispersion of the particles prevails. THE nickel-chromium alloys containing titanium and aluminum are widely used in applications requiring high strength at elevated temperatures. Studies on relatively simple ternary and quaternary alloys'-4 have indicated that the favorable high-temperature properties of these alloys are related to the precipitation of an intermetallic ?'-phase having a structure based On that of the Ni3A1 phase of the nickel-aluminum system. The present investigation was undertaken to identify the minor phases and to study the microstructural changes occurring in one of the more complex commercial alloys as a result of aging in the service temperature range, with particular emphasis on investigating the role of the ?' -phase. The microstructural changes were studied by electron microscopy and the minor phases were identified by X-ray and electron diffraction. MATERIALS AND METHODS Inconel-X alloy was selected for this investigation because the previous studies of Frey, Freeman, and white6 provided extensive information on the variations in metallurgical properties of this alloy resulting from high-temperature aging treatments. Specimens aged 1, 10, 100, and 1000 hr at 1200°, 1400°, and 1600°F were made available for the present use. These were taken from 1-in. round-bar stock of a commercial heat having the following weight composition: 0.04 C, 0.56 Mn, 6.59 Fe, 0.007 S, 0.38 Si, 0.03 Cu, 73.22 Ni, 14.97 Cr, 0.78 Al, 2.38 Ti, and 1-02 Nb. They were solutjon-treated at 2050 for 4 hr and then water-quenched prior to aging. Powder X-ray diffraction patterns were obtained from insoluble minor phases which were separated from the alloys by digestion in the reagent of Mahla and Nielsen.6 Back-reflection patterns were obtained from electrolytically polished surfaces of the bulk search to detect the ?'-phase' Cu-K a radiation was used in both cases. In the electron-diffraction studies, the general method developed by Heidenreich, Sturkey, and

Jan 1, 1959

By J. Morgan Clements

The manufacture of coke in Peru, as practiced at the coalmines of the Quishuarcancha and Goyllarisquisca districts, is intermediate between the primitive coke-heap and the bee-hive oven. The method of coking is quite simple. In constructing the coal-heap, preparatory to burning, the ground is first leveled, and a simple stack of stone and clay is built, giving the bottom, to a height of 6 ft., approximately 6 ft. of external diameter. The size of the stack varies in different districts, but is generally 9 ft. high, and slightly smaller at the top than at the bottom. The walls of the heap are from 12 to 14 in. thick, which allows an inside diameter of from 3.75 to 4 ft. These walls are pierced at intervals by three or more tiers of openings or flues, connected with the central flue. The radial flues have a diameter of about 5 in. and are built with a gentle upward slope. The stack (shown in Fig. 1) is permanent; and in this respect the practice in Peru differs from other primitive practices in which nothing is permanent except the yard. Above the permanent 6-ft. portion of the stack there is added a cap of clay, about 3 ft. high, which contracts toward the top, where it has an inside diameter of about 2 ft. This clay cap is temporary, and frequently has to be renewed after each burning. Before charging the coal, there are first built, from the lowest tier of flues upon the ground, a number of temporary flues, leading from the central stack out to the edge of the coal-heap, and constructed of blocks of coal for the greater part of the distauce, the outer edge alone being of rough stoue. The coal is then piled up over these flues and around the stack to a height of about 6 ft. The bottom flues are the only ones that

Jan 1, 1905

For a nation whose mining industry has generally been floating through history in the shadows of major mining developments elsewhere in the world, Australia has in the decade of the Sixties made a convincing bid to be one of the world's great "store- houses" of minerals. In fact, at the rate things are developing Down Under and Out Back, what with professional prospecting teams crisscrossing the continent under the direction of professional exploration management, Australia may one day find itself as the world's greatest storehouse. Whereas Necessity may be the Mother of Invention, Consumption is surely the Mother of Exploration. At least this is true in Australia of today. First, the forecasted shortage of iron ore in the world led to the fabulous discoveries in the Pilbara district of Western Australia. Now, the demand for nickel has generated even more interest among mining companies in the vast, untapped potential of Australia.

Jan 10, 1968

By A. B. Kinzel

PRECISE knowledge regarding the effect of heat treatment on the properties of steel has made possible the detailed specifications and instructions covering optimum heat-treating temperatures and practices that are in current use. A distinct contrast is presented by the metallurgical treatment of steel adjacent to a fusion weld, as such steel is subjected to each temperature from room temperature to fusion temperature, and cooled at a rate that is not generally controllable but is predetermined by the nature of the assembly to be welded, the kind of welding used, and the surrounding conditions. This is true regardless of the type of fusion welding: oxyacetylene, electric arc, thermit or flash resistance. Therefore it seemed desirable to investigate the effect of this metallurgical treatment on the characteristics of carbon steels commonly used for welding, by a detailed study of metal subjected to each temperature range; i.e., each heat-affected zone. Oxyacetylene welding was chosen for the investigation because of the experimental facility of accurately segregating and studying each temperature zone. The nature of the zones produced by other types of welding is the sane. The difference is primarily a matter of dimensions of each of the temperature zones involved. The advantages and disadvantages of the extent of the zone are of prime moment, and are discussed after the presentation of the detailed zone study. No mention is made of the fused metal proper, as this has been the subject of much published research and the nature of the solidified metal is fairly well known. GENERAL METHOD The scheme of procedure in the work herein reported involved the testing of the metal of each temperature zone adjacent to the weld in so

Jan 1, 1935

By Albert Hayes

FOUR mines at Wabana, on Bell Island in Concep-tion Bay, Newfoundland, produced 1,209,777 tons of ore in 1927, and it is expected that the produc-tion will be larger in 1928. The ore is a stratified oolitic hematite of sedimentary origin. Three workable beds and many thin beds occur in a thickness of 400 ft. of interbedded sandstones and shales. It is not profitable under present conditions to mine extensively in ore beds less than 4 ft. thick. The iron ore beds outcrop on the small island and are inclined northward more steeply, than the slope of the ocean bottom. The mine work-ings follow the bedded ore below the sea bottom, No. 3 Mine extending about 2 miles north of the island. At this point there is a cover of 1500 ft. of rock and 600 ft. of ocean water. It is impracticable to operate drills in the ocean to prove the extent of the submarine orebody in advance, and diamond drilling from the mine workings is the only method of exploration. Bell Island has been settled for a long time and a monument at Cupids, near Brigus at the head of Conception Bay, commemor-ates the tercentenary of a settlement there in 1611 by Captain Guy of England. was one of the chief ports of Newfoundland for deep sea fishing and doubtless many a captain wondered about the red rocks as he sailed past. The famous geologist, J. B. Jukes, records seeing a bright red sandstone 8 ft. thick on the northwest side of Bell Island during a visit in 1842, but he evident ly did not try to land on that rocky coast to get a sample. The iron ore is plainly visible in the high cliffs along the coast of the island, as bright brown layers interbedded with gray and white sandstones and dark shales. The heavy red rock was used by the fisher-men as anchor weights for fish nets and small boats, but its real value, so the story goes, was discovered by a merchant in Saint John,

Jan 8, 1928

By M. N. Shetty, A. C. D. Chaklader

RECENTLY, it has been demonstrated that a considerable densification and interparticle bonding can be achieved if a pressure is applied to a powder compact while the material of the compact is undergoing either a decomposition reaction' or a polymorphic transformation.' The term "reactive hot pressing" has been coined to identify this process in which a phase change is combined with pressure to achieve interparticle bonding. This process is based on a principle which postulates that there is an enhanced reactivity and mobility of the molecular species at the phase-transformation temperature and this effect is utilized for interparticle bonding in powder compacts. This note summarizes the results obtained in an attempt to utilize this technique to produce ceramic-metal composites. In this case, a decomposition reaction of a compound (which after decomposition yielded an oxide) was used to achieve interparticle bonding in ceramic-metal composites. The reactive hot pressing was carried out in a Phillips induction heating unit, using either a graphite or a high-temperature steel die which functioned as both the susceptor and the hot-pressing component. The die was heated to the desired temperature in a helium atmosphere. All cermets produced by this technique were based on alumina as the ceramic phase. Different metal phases such as iron, copper, and chromium were used to study the effect of varying the metal phase on the properties of the composite. a Mono-hydrate (Boehmite) was mixed with different proportions of metal powders (-325 mesh) in dry condition in a mortar and pestle. No special precautions were taken for proper mixing. The mixtures were then compacted into a cylindrical form having an approximate dimension of 1 cm in diameter and 1 cm in height. For this compaction an ordinary

Jan 1, 1965

By Robert H. Richards

THE Institute of Mining Engineers has shown so much interest in the educational problem of profitably combining theory and practice, that it seems especially appropriate to lay before its members the methods and aims of the mining laboratory of which I have charge, and in which one form of combination of hand with head work is now being tried. If anything may be contributed toward the solution of this problem by the discussion which follows, my purpose mill be attained. Whether it was wise or not to establish a mining school so far from the principal mining centres, does not now enter into the question. Given, a mining school already begun, how shall it be made most efficient in developing engineers who are trained to think for themselves as well as versed in the works of others ? This is the question with which we have had to deal. In considering the bearing of this laboratory work upon the students' preparation, it will be convenient to take it up under five different heads: 1. The methods and aims of the laboratory. 2. The advantage to students of having a part, at least, of their practical work in the curriculum of their school. 3. The advantage to be derived by mine; and works. 4. Degree of accuracy which may be attained in working ores on a small scale. 5. Reslts of work in the laboratory. 1. The Methods and Aims of the Laboratory.—During the May meeting of 1873, held in Boston, I had the privilege of reading before you a paper stating the plan; and aims of this laboratory. Since that time me have been constantly following out those plans, and are more than ever convineed that me are working in the right direction. We do not feel that the time we have spent has been in any sense thrown away. Perhaps the aims of the laboratory can be most clearly shown by illustration. Many young engineers have school thinking that they know everything. They go to the works, and expect to teach the superintendent something and the men a good deal, regardless of the fact that it is this spirit that has prejudiced workmen against schoolmen. They are often more trouble than they

Jan 1, 1879

By Ta M. Li

This article draws freely on the experiences of the engineering and operating staff of P.T. Inco and its parent firm Inco Ltd. In addition, information was derived from papers presented during the recent International Laterite Symposium, held in conjunction with the 1979 AIME Annual Meeting, New Orleans, La., February 19-21. The author wishes to acknowledge all contributors and, in particular, Roy Aitken, president and managing director, P. T. Inco.

Jan 7, 1979

Executive-A. R. Ledoux, chairman. Membership-J. V. W. REYNDERS, chairman. Finance-J. V. N. Dorr, chairman. Library-E. GYBBON SPILSBURY, chairman. Papers and Publications--BRADLEY STOUGHTON, chairman. Nominations-Pope YEATMAN, chairman.

Jan 11, 1919

By P. W. George

THE rapid increase in cost of discovering new orebodies by churn drilling in the Tri-State district has led to some attempts to lessen the expense by using geophysical methods. Electrical prospecting was tried three or four years ago, but no successful results were recorded. In 1926, the Federal Mining and Smelting Co. engaged the North American Exploration Co., of Houston, Texas, to make some tests with the torsion, balance. At first, it was thought that the most favorable conditions for discovery of ore deposits with the torsion balance would be in locations where the ore was known to occur at rather shallow depths, FIG. 1.-CROSS-SECTION OF DUENWEG LEASE. therefore the first trial was made at Duenweg, east of Joplin, where some zinc ore had been developed at a depth of 130 ft. The gravity gradients at 61 stations on a tract of about seventeen acres indicated plainly one large zone of maximum gravity and a smaller narrow zone of minimum gravity. Fourteen churn-drill holes, half of which struck .ore, show that all the ore found was located outside the zones of maximum and minimum gravity. In the zone of maximum, gravity the limestone beds were closest to the surface, and the first chert beds encountered were at the greatest depth. The results (shown in Table 1) indicated that the gravity of the limestone was greater than the gravity of the fractured chert together with its orebodies, and probably also greater than the bouldery soil and clay on top of the limestone. A cross-section of the Duenweg lease is shown in Fig. 1.

Jan 1, 1928