Search Documents

By R. C. Gifkins, A. Gittins

A. Gittins and R. C. Gifkins (University of Mel-houvne)— Evidence from somewhat similar experiments to those described in this paper has led us to the conclusion that possibility 2) of the four listed on p. 319 is a description of what happens in grain boundary sliding. That is, sliding is limited by accommodation deformation, it being necessary to the Continuance of sliding that this accommodation should take place. An example of such accommodation, though probably not the most important, is fold formation at triple points. The evidence and arguments for this point of view are set out in Refs. 14 to 16. In particular, an experiment with a lead bicrys-tall5 seems to support point 2) rather than 3). In creep of this specimen it was found that at least 90 pct of the extension of a zone 0.3 mm wide at the boundary was supplied by sliding at the boundary. The sliding was localized in a region at the boundary very much smaller than 0.3 mm, in fact, in a region too narrow to resolve optically. In poly crystalline Specimens&apos; there appears to be a surface effect, as found by Rachinger," but it appears that this may not manifest itself at low strains. "Low strains" means <10 pct for a Pb-TI alloy, <2.5 pct for magnesium or "Magnox" A12 alloy, or <40 pct for a 0 brass. Up to this extension the sliding, measured by the mean vertical step at boundaries, is proportional to extension. We are able to say this with some confidence, since the error bars on our points are statistically derived. Our results would lead us to think that the error bars on other work, including that of Mullendore and Grant, are much too large at low strains to show this

Jan 1, 1963

By D. W. Fuerstenau

In 1940 Schuhmann1 showed that the size distribution of a comminuted material can be expressed by the following empirical relationship: y = 100 (|f [i] where y is the cumulative percentage of material finer than size x, k is a size modulus, and a is a distribution modulus which is constant for a given material and machine. During the past few years, considerable emphasis has been given to the investigation of the extent of size reduction resulting from the expenditure of mechanical energy in crushing and grinding. Recently Schuhmann&apos; presented a derivation of the energy-size reduction relationship by postulating that comminution in a device such as a ball mill can be considered to be the summation of many single comminution events, each of which yields a size distribution of particles following the Schuhmann size distribution equation. By grinding

Jan 1, 1961

Visitors frequently put the question to Kalgoorlie gold miners; "Why don&apos;t you concentrate your mining operations?" A mine may be drawing ore from over a hundred different working places which are spread out over several thousand feet of strike and on many different levels. The answer to this question is that "finished" can rarely be written for a section of the mine. The intricate web of mineralization in faults, shears and fractures is an endless puzzle, each solution opens up new avenues to be explored. After the last ore is taken from a stope, a program of drilling may continue for several weeks on different possibilities. Perhaps no ore is discovered and drilling is abandoned, but it is not unusual for another search to begin later in that same area on a new theory with successful results. Wherever a slightly richer mineralization is found, it is needed to "sweeten" the mill heads. Over seventy years ago gold was discovered in the dry wastes of Western Australia. Rich deposits of alluvial gold were found at first and as these were worked out they led to the discovery of the lode ores, which were leaner and harder to extract.

Jan 10, 1964

By G. Derge, R. E. Grace

Diffusivity of bismuth in liquid Pb-Bi alloys has been measured by the capillary reservoir method as a function of temperature and composition. Fair agreement between theory and experiment is found for the measured diffusion coefficients and activation energies of diffusivity and viscosity in dilute lead alloys. The measured diffusion coefficients in the high bismuth alloys describe mass transport in special concentration gradients. THE study of diffusion in liquid metals has been restricted largely to the amalgams over small ranges of temperature and composition. In contrast to this, diffusion and transport of ions and molecules in aqueous and organic solvents have been studied extensively for the past 50 years. The general difficulty of measuring diffusion coefficients in both gases and liquids at high temperatures has been that of eliminating convection currents. Measuring techniques based on freezing and sectioning after the diffusion period1 are not particularly satisfactory because of the volume changes and segregation which occur during freezing. The most promising technique which is currently being developed for liquid metals is the capillary reservoir method. This eliminates convection currents from the diffusion zone and requires measurements only of the length and initial and final compositions of the alloy within the capillary. Anderson and Saddington&apos; have measured the diffusion coefficient of tungstate anions in aqueous Na,W04; Wane4&apos; and Hoffman- ave studied structure and self-diffusion in water and self-diffusion in mercury, respectively, by similar techniques. Selection of the Pb-Bi system for initial study was made for several reasons: I—It afforded a low temperature system for development of techniques which would be suitable for high temperature measurements in liquid iron. This research on diffusion in liquid iron is now in progress as a part of a general program on the rates and mechanisms of slag-metal reactions. 2—Activity data on liquid Pb-Bi alloys of all compositions are available from the emf meas- urements of Strickler and Seltz.9 3—Some data are available on the diffusion of bismuth into solid lead. The measurements on solid alloys were made by von Hevesy and Seith7 for the concentration range of 0 to 2 pct Bi. An appropriate solution to Fick&apos;s law (unsteady state) for the capillary reservoir has been found by considering the mass flow which passes through a unit area of surface on a slab of infinite thickness as a function of time. This is the first application of this solution to diffusion measurements, although a similar solution is available for identical boundary conditions.&apos; By analogy with heat conduction, the problem reduces to a perfectly insulated infinite slab at temperature C,, one surface of which is quenched to C, for all times, t. Heat is permitted to flow from quenched surface of the slab to an infinite supply of coolant at C.&apos; (see Appendix). For the corresponding solution for diffusion in liquids, these terms become Where Cu is the initial concentration of component A" in entire capillary at t - 0, C, is the final con- In this case. component A is bismuth, and C, = 0. centration of component A in entire capillary at t = t, C, is the concentration of component A in bath for all t, 1 is the length of the capillary in centimeters, t is the time of diffusion period in seconds, and D is the diffusion coefficient in square centimeters per second. By comparison with solutions to Fick&apos;s law used in the solid state, this solution for liquids is similar to the Grube solution for solids, where the change in D with chemical composition is not taken into consideration. Difficulty is to be expected if large concentration gradients are employed and if the concentration gradients extend over an appreciable length of the capillary.

Jan 1, 1956

SINCE you have asked me many times in particular how those mirrors are made that are commonly called spheres,* and even though I have told you at other times, I do not wish to omit writing of it here again in detail, so that you may have as complete information as I can give you, both in order to satisfy you fully and because it belongs among the subdivisions of the subject that I have proposed. Concerning this, I first tell you that it was an ancient discovery, and in those times as today was celebrated, and worthily so. For the effects these mirrors produce are miraculous things incomprehensible to me, and the more I think about it the more I am bedazzled with wonder, nor do I know how to explain by theory of perspective the causes demonstrated by their effects. Marvelous indeed is the beauty of their shining clearness, but much more so is the fact that (according to the shape that the craftsman has chosen to give them) they reflect back the shadow of the things

Jan 1, 1942

By George W. Hezzelwood

THE Balatoc mine, one of the Haussermann group,† is on the Island of Luzon, the largest of the Philippine group, about 260 km north of Manila, and 12 km from the city of Baguio The Baguio district is the most important gold-mining area of the Philippines, with 14 producing mines in 1939, milling 2,358,804 tons of ore, yielding [P]40,881,048, approximately 55 per cent of the total Philippine production of [P]74,131,216 PRODUCTION HISTORY The Balatoc mine began production In January 1929 with a 150-ton cyanide mill Increases in mill capacity have taken place as follows March, 1932, to 330 tons June, 1933, to 470 tons December, 1933, to ;15 tons July, 1934, to 700 tons December, 1934, to loon tons May, 193, to 1200 tons October, 1938, to 1300 tolls April, 1939, to 2000 tons January, 1941, to 2T50 tons Production during the period of expansion has steadily increased in total value in spite of the fact that grade of ore milled has dropped-from $31 06 in 1929 to $5 78 in1940 Annual reports give production as shown in Table I, the average value, being based on gold at the old price of $20 67 per ounce [ ] GEOLOGY The ore occurs in quartz-calcite veins that vary in width from narrow stringers to mineralized zones 40 to 30 ft wide Wall rocks consist largely of diorites, with some andesite, and a fragmental breccia called locally the "Balatoc plug " Texture of the ore varies widely in the different vents-from a soft, highly altered, gouge material filled with quartz fragments through a soft, unaltered quartz-calcite to a hard, massive quartz ore Three major vein systems have been extensively developed, and smaller amounts of work have been done on several others These veins strike east-west to N 60°, clipping south from 50° to 90°, and are essentially tension breaks between a series of faults or shears striking N 30°E to N 30°E and clipping southeast from 50° to 90° The shear veins and tension veins probably formed more or less simultaneously,

Jan 1, 1942

By D. Harker, E. Epremian

The constitution of the nickel-tungsten system has been studied by a number of investigators, the most recent of which are Ellinger and Sykes.1 On the basis of metallography, electrical resistivity and hardness measurements and some X ray diffraction work, they constructed a consitution diagram (Fig 1). Ellinger and Sykes report a0 for the alpha face-centered cubic phase (nickel saturated with tungsten) as 3.66?.‡ The gamma phase (tungsten saturated with nickel) is given as body-centered cubic, but no value of a. is recorded. At 43 pct tungsten by weight (approximately 20 at. pct) a beta phase is reported, but structure and lattice parameter are not known. Primarily on the basis of metallographic evidence, they conclude that beta is a new phase and rule out the possibility of formation of a superlattice since they- observe a new phase in the microstructure. Grube and Schlecht2 report an ordering reaction in a system similar to the Ni-W (Ni-Mo) and Harker3 has shown that NirMo forms a superlattice upon the pre-existing face-centered cubic lattice of the alpha phase. Elliniger arid Sykes observed a change in the diffraction pattern of a 4.3 pct W alloy upon aging and attributed it to the formation of a new phase. Thus, there appears to be some question as to the character of the beta phase reported by Ellinger and Sykes. The purpose of the present work is to determine precisely the structure and nature of the beta phase in the Ni-w system of X ray diffraction methods. Experimental Procedure One inch diameter ingots of 43.66 pct, 40.15 pct and 34.06 pct .tungsten by weight (19.8, 17.6 and 14.1 at. pct respectively) were melted and cast under vacuum from electrolytic nickel and pure wire filament grade tungsten. The ingots were soaked for 16 hr at 1300°C in a hydrogen atmosphere furnace, then swaged at this temperature and finally drawn to 0.020 in. diam wire. Some of the bar stock was retained in 1/2 in. diam rod for hardness and metallographic studies. Wire samples for diffraction work were sealed in evacuated quartz tubes and subjected to the various solution and aging heat treatments in a hydrogen furnace. X ray photograms were taken in a Debeye-Slierrer camera using copper K radiation filtered by nickel foil. Results X RAY DIFFRACTION The lattice parameters of the alpha and gamma phases at saturation were determined by an X ray photogram of the 19.8 at. pct W alloy after solution heat treatment at a temperature well within the alpha-gamma range above the peritectoid temperature (17 hr at 1150°C—oil quenched). The alpha phase was found to be face-centeted cubic with a. of 3.594 ± 0.001?, while the gamma phase was determined as body-centered cubic with a. of 3.158 ± 0.001?. Exactly the same phases and parameters were ohtained with the 17.6 at. pct W alloy for the same solution heat treatment. Thorough analysis was made of an X ray photogram of a 19.8 at. pct alloy sample in the quenched and aged condition (solution treated 1T hr at

Jan 1, 1950

By E. R. Palowitch, P. H. Broussard

The United States aims to achieve some modicum of energy self-sufficiency through means such as conservation, increased domestic oil and gas production, substitution by the electric utilities of coal or coaloil mixtures for oil and gas, and development of a viable synthetic liquid fuels industry. Coal&apos;s role in attaining this goal will necessitate doubling coal production by the end of the 1980&apos;s. And if the United States does in fact become the World&apos;s Saudi Arabia of coal, the total annual production to meet these domestic needs and export markets could double again by the year 2,000. As only a small portion of our Nation&apos;s reserves are recoverable by state-of-the-art surface mining methods, most of the coal produced in the future will have to be mined underground (Averitt, 1975). But this projected increase in coal demand is occurring in the face of a decade of radically decreasing productivity. Specifically, average worker productivity in underground coal mines has decreased from 14.2 tonnes (metric tons) per workershift in 1969 to 7.2 tonnes per worker-shift in 1979; and 95 percent of coal produced underground during this period was produced by room-and-pillar methods (U.S. Dept. of Energy, 1980). Although there is no complete agreement on the impact of recent Federal legislation, there is strong correlation between the dramatic decrease in productivity in underground coal mining and the implementation of the recent Federal mine health and safety regulations (U.S. Congress, 1969). A review of the wide range of coal mining research, development, and demonstration projects currently being funded by the federal government and by industry gives little encouragement for increasing worker productivity on room-and-pillar sections underground in the immediate future (Palowitch, 1978). Conversely, the opportunities for increasing production/productivity underground with longwall methods appear somewhat more encouraging. Although at least one longwall face in the U.S. did produce more than one million tonnes of coal in a single year, the national two-shift average production from one hundred or so longwall faces is about 1,000 tonnes per day (Huwood-Irwin Co., 1978 and Consolidation Coal Company, 1976). Clearly, there exists some real opportunities for improvement. One of these opportunities is to automate the cutter-loader.

Jan 1, 1981

By R. J. Marcotte, C. T. Eddy, R. J. Smith

The objectives of the investigation herein reported were to determine: (I) the S-curves for certain selected cast steels, (2) whether or not the published S-curves for wrought steels are satisfactory for use on cast steels of similar composition, and (3) to prepare hardenability curves of the selected cast steels. In order to make the final comparisons between cast and wrought steel more completely tangible, it was deemed advisable not only to determine S-curves for the steels submitted in the cast condition but also to roll some of the cast-steel test bars and determine comparison S-curves on such wrought material. This procedure eliminates the composition variable and makes it possible to reveal the differences resulting from plastic deformation of the cast structure in addition to providing the comparison with published data on wrought steels. Cast Steels The cast steels selected for the preparation of S-curves, or time-temperature transformation curves, were similar to S.A.E. series 1030, 2330, 4130 and 4330. Of these the 1030 was supplied by The Crucible Steel Casting Co., Cleveland, Ohio, and the other three by The Sawbrook Steel Castings Co., Lockland, Ohio. The steels were furnished in the as-cast condition. The manufacturers supplied the chemical analyses and the properties that could be obtained in the heat-treated condition—all of which is summarized in Table I. The metallographic and dilatometric procedures and equipment were in general standard. The specific technique employed was described in a report of the Steel

Jan 1, 1945

By H. W. Seamon

THE data here given were obtained by 1500 tests made, by the United Verde Copper Co. to determine the most economical air pressure for the operation of hammer drills under the varying conditions of use, and to investigate the variation in drilling speed at different air pressures Twelve models of drills were used at gage pressures ranging from 40 to 130 lb. No effort was made to harmonize theory and practice; but rather to formulate empiric rules that would cover the. average variation of the results obtained. These rules on the performance of hammer drills, based on the air pressure as the main variable, however, are not necessarily of universal application, but they apparently satisfy the results obtained in this series of tests. The drilling conditions at this property vary widely; an average of twenty-one machine shifts to a 3-ft. (0.9-m.) round has been found necessary in some of the development work, while an, advance of 56. ft. has been made in seven shifts in the "oxide" ground. This range pre-eludes the adoption of one type of drill as a standard; consequently almost every kind of hammer drill sold in this country has been tested. At present, sixteen models are in use, of which two types of the heavy (150 to 160 lb.) mounted drills, one of the light mounted drill, one stoper, and two hand plugging drills are considered as standard.

Jan 1, 1921

By Arthur Philips

THE purpose of this paper is to present certain data and observations resulting from a series of experiments dealing with the heat treatment and microstructure of commercial white cast iron and its derivative, malleable iron. In planning the experimental work, particular pains were taken to secure for the tests white cast iron of "normal" composition; i.e., within the composition limits commonly prescribed by manufacturers of malleable castings. A review of the literature leads us to believe that much data of a fragmentary character treating of the graphitization of white cast iron have been of little value, mainly because of the diversity in chemical composition of the materials employed in the tests. Moreover, when feasible, annealing periods at least comparable to those of current practice have been adopted. We wish to acknowledge our indebtedness to the members of the research department of the Eastern Malleable Iron Co. for the white cast iron used in the tests and, particularly, for their active cooperation during the experimental stage of the work. In this paper the following subjects will be discussed in the order indicated: Data on the thermal critical points of white cast iron and malleable iron. Changes produced in tensile properties and microstructure of white cast iron by annealing at different temperatures within the range, 760 to 1100° C. Relation of thickness of wall section of hard iron to microstructure and tensile properties of malleable iron obtained under normal annealing conditions. Notes on mechanics of graphitization of normal white cast iron as observed in specimens quenched after various periods of anneal at approximately 800° C.

Jan 1, 1922

By Russell Spry, Paul Schutz

The property of Pioneer Gold Mines of B.C. Limited is in the Lillooet mining district of British Columbia. It is on Cadwalleder Creek, 54 miles distant by motor road from Shalalth, a station on the Pacific Great Eastern Railway. Interests identified with the present company installed a small amalgamation plant on the property in 1924, consisting of a jaw crusher, Bryan mill and amalgamation plates, in which 75 per cent extraction was made on mill feed averaging 1.0 oz. gold per ton, the tailing being stacked for future treatment. That plant was operated until 1928, when the present company was formed and a 100-ton continuous counter current decantation cyanide plant was built. A second unit, having a nominal capacity of 200 tons daily, was added in 1932 and put into operation during September of that year. When handling ore comparatively free from slow-settling material, the combined capacity of the two units is 400 tons, the original plant now handling about 140 tons maximum. Production to date, from Pioneer, has been about $6,500,000, the present monthly production being better than $250,000 from about 370 tons ore daily, the recovery being 97 per cent. During the fiscal year ending March 31, 1934, a total of 112,936 tons ore and old amalgamation tailing was milled, the mill feed averaging 0.7670 oz. gold and the recovery amounting to 0.7422 oz. gold per ton, or 96.77 per cent. Milling costs, including refining and mint charges, during this period, amounted to $1.45 per ton of ore. Since the building of the first unit of the cyanide plant in 1928, direct cyanidation has been employed, no attempt being made to remove coarse gold from the circuit, other than that cleaned up from the grinding mills during relining and from the classifiers, as occasions permit. In the hope of still further increasing recovery, researches are going forward at this time with the view to removing some of the sulfides after primary grinding, the expectation being that selective treatment of this more refractory portion of the ore may hold economic possibilities.

Jan 1, 1935

By H. W. III Straley

SOME ten years ago the writer1 made a survey of college catalogues to determine what sort of training geologists were receiving in basic sciences. In the light of this compilation and subsequent experience, he made the statement at the 1939 meeting of the Institute that apparently only in schools offering a curriculum in geological engineering or in the geological option of mining engineering curricula could geologists hope to receive the training advocated by Hubbert.2 In the former study, schools of engineering were excluded because the preparation was known beforehand. The present study aims to consider engineering schools in an effort to determine not only what basic studies are required but what use is made of them in geological courses of the third and fourth years. The present study combined the method of consulting catalogues with a questionnaire. Letters were mailed to officials responsible for supervision of mineral industries curricula requesting information on: (I) the extent to which the engineering preparation of the first two years is actually used in the work of the last two; (2) the extent to which the engineering of the last two years is used in courses in geological engineering or geology; and (3) whether geologists or geological engineers teach descriptively or analytically. Both methods of securing information are open to criticism; the former on the basis of the incomplete information supplied by university catalogues concerning prerequisites and curricula and the latter on the ground that the questions may be phrased poorly or given insufficient consideration by replying officials. Fifty-six questionnaires were mailed and 39 (70 per cent) replies were received. Of the replies, 6 (11.3 per cent) were from colleges of liberal arts unconnected with engineering schools, 11 (20 per cent) were from schools having curricula in geological engineering and 22 (39 per cent) were from departments of mining engineering. The number of replies and their distribution were satisfactory in spite of the receipt of only six from liberal arts colleges. It should be understood that the universities of which the catalogues were examined were not necessarily the same in both compilations. No departments that are admittedly or known to be acting solely as service departments were recorded in the second study. Table I shows that all professional schools require mathematics through calculus, whereas only 7 per cent of the liberal arts curricula expect the same level of preparation; only 73 per cent require trigonometry and 40 per cent college algebra. The proportion of geological engineering curricula requiring differential equations is higher than mining. All of the engineering schools require general and analytical chemistry, whereas only 77 per cent of liberal arts curricula require general and 18 per cent analytical. Twenty-two per cent of the mining and 40 per cent of the geological engineering

Jan 1, 1941

Jan 1, 1908

By Robert L. Akright

LOCATION AND HISTORY The Candelaria silver mine is located in an arid, isolated desert setting in Sections 3 and 4, T.3N., R.35E., and Section 33, T.4N., R.35E., Mineral County, Nevada (Fig. 1). Silver was discovered in 1863 by Mexican explorers, and high grade silver veins were mined from the early 1870s through the 1880s. Essentially all mining had ended by 1890. The veins were mined by underground methods typical of the period. As is the case in many mining districts, Candelaria was studied and explored by a number of companies. All these efforts were terminated short of mine development because of low silver prices and difficult metallurgy. On March 1, 1976, Occidental Minerals (Oxymin) entered into a Limited Partnership agreement, known as Candelaria Partners, as General Partner with Congdon and Carey Ltd. No. 4. Prior to the agreement, Congdon and Carey had acquired the candelaria properties as part of a bullish silver program and did considerable exploration which indicated the possibility of a large reserve of shallow silver mineralization. GEOLOGY AND ORE DEPOSITS Silver and gold mineralization in the Candelaria district occurs in high-grade fissure veins with silver values ranging from 0.6 to 7.8 kg/t (20 to 250 oz per st). These veins, combined with the low grade disseminated mineralization in the intervening material between the veins, form Manto- like deposits 15 to 46 m (50 to 150 ft) thick. Three such deposits are found in the Candelaria district: the Lucky Hill, Mount Diablo, and Northern Belle deposits (Figs. 2 and 3). The average ore grade of the Lucky Hill and Mount Diablo [ ]

Jan 1, 1985

By Floyd Kelley

THERE is an ever-increasing demand for furnaces with controlled atmosphere, due to the large quantities of steel being used in the automotive industry, such as the .high-chromium stainless irons, the 18 Cr, 8 Ni stainless iron and low-carbon steel sheets. The difficulties involved in the annealing of such materials, if they are to be kept absolutely free from oxidation, are many. It is possible to bright-anneal these steels in small laboratory hydrogen furnaces, using specially purified hydrogen and taking some additional precautions. In the first place, the insulation, usually of alumina or magnesia, holds small amounts of water vapor, which it is almost impossible to remove completely. Secondly, there is always condensation of water vapor in the cooling chambers of such furnaces, and with the continuous circulation of the hydrogen gas in the furnace, the water vapor is carried from the cooling chamber back into the heating chamber. This water vapor oxidizes the charge. Lastly, the supply of moisture is made sure by the diffusion of small amounts of air from the atmosphere into the furnace against the pressure of the hydrogen. The oxygen combines with the hydrogen and forms more water. Under such conditions there is, little gained by using specially purified gas, because it becomes contaminated after reaching the furnace.

Jan 1, 1931

By R. W. H. Atcherson

BLAST-FURNACE flue dust is one of the most troublesome operating factors in the iron and steel industry. It is usually involved in all the unpleasant phases of blast-furnace operations. It adds to our aggravations until we are willing to spend large sums of money to keep it out of our stoves and boilers acid more money to handle it again and again on one scheme or another to induce the furnaces to retain it without bad after effects. Several successful operators claim that it is useless to recharge raw flue dust because the furnace would never have blown it out if it had been suitable material for blast-furnace consumption. Most of us who have made persistent efforts to return raw flue dust to the furnaces have decided that it is very often false economy to do so. Yet some remarkable results have been attained at the Ohio Works of the Carnegie Steel Co. through recharging raw dust. The plant comprises six modern blast furnaces. Up to 1909, about 300,000 tons of flue dust had accumulated in stock piles. During the last 10 years, there have been recharged into these furnaces all of the flue dust recovered from the furnace operations, the entire stock pile of flue dust, and nearly 80,000 tons of dust shipped from other furnaces of the Carnegie Steel Co. The results obtained are shown in Table 1.

Jan 2, 1920

By Charles S. Barrett, Robert F. Mehl

The system cadmium-mercury has attracted much attention, chiefly because of its importance in the study of electrochemical standard cells. The constitutional diagram, as it is accepted today, is essentially that developed by Bijl l (Fig. 1), though there has been a great amount of work done on the system by other workers.2 A year ago the senior author published a paper on the crystal structure of the system, in which were described determinations of crystal structure

Jan 1, 1930

By A. E. Dwight, A. F. Berndt

ThE published U-Ru equilibrium diagram indicates the existence of six intermetallic compounds in this system.&apos; The structure of only two of the compounds, u2Ru2,3 and URU3,4 have been identified. This communication reports on the crystal structure and density of Uau3, which is formed by a peritectoid transformation at 1025° ± 5°C: U3Ru4 + U3Ru5 = U2Ru3. An alloy with the stoichiometric formula U2Ru3 was prepared by arc melting electrolytic uranium and ruthenium of 99.9 pct purity on a water-cooled copper hearth under an argon atmosphere. After homo-genization at 1000°C for 3 days, a metallographic examination revealed that the peritectoid transformation was complete and less than 5 pct of a second phase was present. A powdered sample, obtained by crushing the brittle compound, was annealed for 1 hr at 1000°C and air-cooled. Debye-Scherrer patterns were obtained with filtered CrKa, FeKa, CoKa, or CuKa radiation. The X-ray patterns of U2Ru3 weFe indexed as an fcc structure with a. = 12.895 0.00lA. The unit-cell constant and its standard deviation were calculated by a computer program described by Mueller, Heaton, and Miller.5 The density, measured by an immersion method, was 14.45 g cm-3. A calculated density of 14.48 g cm-3 was obtained on the assumption that twenty-four formula units (120 atoms) comprise a unit cell. The space group is either oh7 Fd3m, or the less symmetric, T4h, Fd3, since reflections indexed as hk0 with h + k + 4n are absent. All values of h2 + k2 + 12 permitted by both space groups are listed in Table I together with dc, do, and I. values. The calculated d spacings were obtained by the computer program of Mueller, Meyer, and simonsen.6 The observed d spacings above 0.77A were obtained from X-ray" patterns prepared with CuKa radiation, above 0.90A with CoKa radiaaion, above 0.98A with FeKa radiation, and above 1.16A with CrKa radiation. An attempt was made to identify the crystal structure of U2Ru3 by comparison with published data on other A2B3 compounds. A recent compilation7 of intermetallic compounds lists thirty-two structure types with the A2B3 stoichiometry. Only two of the structure types are fcc and they are Sb2O3(r), senarmontite, with 16 Sb2O3 per unit cell, and In2Te3 for which several structures have been proposed.8 However, the two cases cited do not have twenty-four formula units in the unit cell. We therefore, cannot identify UPRU3 with any of the other known A2B3 compounds. Ternary alloys were made in which 5 at. pct Os, Rh, or A1 were substituted for 5 pct of the Ru in U2Ru3. The osmium substitution increased the unit cell constant to 12.899 * .001A, which is to be expected since the atomic volume of osmium is slightly larger than

Jan 1, 1969

By W. Petruk, R. S. Boorman, R. Gilders

Approximately 33% of the silver in the Zn-Pb-Cu-Ag ore of Brunswick Mining and Smelting Corporation Limited is lost to the tailings and an additional 11% to the zinc concentrate for which no payment is received. 38% to 44% of this lost silver is carried by tetrahedrite, 28% by galena and 28% to 34% by a third silver carrier. The silver minerals acanthite and pyrargyrite have been identified in mill products and hence these are suggested as the principal third silver carrier(s) accounting for 13 to 20% of the silver in Brunswick ore. About 24% of this third silver carrier assemblage is lost to the zinc concentrate and 52% to concentrator tailings.

Jan 1, 1984