Search Documents

By G. C. Fryburg, H. M. Murphy

ThE rates of oxidation of metals are usually obtained by heating the metal specimens in furnaces. Such a procedure is satisfactory for most metals. However, there are several metals that oxidize according to the reaction.

Jan 1, 1959

By E. E. Mason

The Canadian National Railway system is completing construction of the first major tunnel in North America to use the coarse-aggregate (+ ½ -in.) shotcrete technique of primary support and lining. The tunnel was driven 29 X 20 ft in cross section, 10,760 ft long, passing under an industrial and residential area of Vancouver. With the exception of 1400 ft in soil (mainly impervious tills), the tunnel passes through a very young series of flat-lying sedimentary beds, to a large extent so incompletely consolidated as to fall apart on exposure. For a conventional steel-support system, it was estimated 8 WF, 28-lb steel should be used at 5-ft centers. Cost of erection including lagging would amount to $120 per linear ft of tunnel at 304 per lb. With 8-in. concrete cover on the steel, lining would cost $280 per linear ft at $82 per cu yd. Thus, minimum cost of support and lining would have amounted to $400 per linear ft. It is now estimated that at least 90% of the rock tunnel would have required support and 100 % required lining. Specified shotcrete support was 6 in. in the arch and 4 in. in the walls. Cost of this work was roughly $100 per linear ft. In addition, another $10-$12 per ft has been incurred in drainage and waterproofing wet areas and in measures to correct experimental and operational errors, thus finalizing the support as a lining (Fig. 1). The tunnel was driven three shifts five days weekly, no blasting being allowed by city ordinance between midnight and 7.00 a.m. A six-drill jumbo was used to drill a 10-ft round, 110 holes blasted three times daily. A 2-in. layer of shotcrete was applied to the newly blasted arch commencing within 45 min of blasting. This was done from a flying deck that extended over the muck pile from the jumbo (Fig. 2). Also during the mucking cycle, the preceding incomplete arch support was brought up to 6-in. specification. The walls were sprayed 4 in. thick during the drilling cycle (Fig. 3). The shotcrete machines and aggregate bins were mounted on the jumbo.

Jan 1, 1970

By Donald W. Scott, Adam Wesner

This paper describes the study of 23 nonmagnetic iron-formation samples from the Mesabi Range and shows the significance of their chemical, mineral, and physical properties in terms of their concentration. Data presented here resulted from a research project carried out from 1942 to 1952 by 10 major producers of iron ore, working in conjunction with Battelle Memorial Institute. THE inevitable depletion of Mesabi direct-shipping iron ores, hastened by recent wars, has increased the importance of developing methods to concentrate iron-formation materials. Many mining companies, independent research organizations, chemical companies, and equipment manufacturers are devoting attention to this important work. It is only natural that magnetic iron-formation materials have received major emphasis, since magnetic recovery methods apply and reserves of Mesabi magnetic taconites are large. However, the nonmagnetic* iron-formation materials are likewise believed to represent a large reserve and their study has not been neglected. tions over the years have shown that in addition to the unenriched taconite, which is dense and hard, and the direct-shipping ore, there are transition taconites grading into the friable wash, or intermediate ores. The transition taconites are less massive than the unaltered taconites and usually coarser-grained. This variation, coupled with the fact that there were no extensive drillings in the unaltered taconite, posed a most difficult problem of obtaining samples that would be representative of large tonnages of the fresh rock. The problem was increased by the tremendous extension of the nonmagnetic formation materials on the Mesabi and by the question of their accessibility to mining. A drilling program was evolved that would surmount these difficulties. Selection of samples was made by a committee representing producers in the area. The samples were procured from 1—taconite walls near bodies of stripping burden or wash ore and 2—from shafts in the process of being sunk through taconite for drainage or mining operations. Most of the samples were obtained from the cherty horizons because it became obvious early in the program that the slaty horizons represented an exceedingly difficult concentration problem, owing to the character of the gangue minerals and the fine grind required for liberation of the valuable minerals. More samples were procured from the lower cherty horizon than from the upper cherty because it was more accessible to mining. It is not known how well the samples selected represent the nonmagnetic iron-formation material. However, they were chosen by people Well acquainted with the geology of the Mesabi range and the mining problems involved. It is believed that they represent a fair cross-section of the types of materials that will be encountered. Table I gives data on the origin of the 23 samples and the horizon footages from which they were obtained. Samples 1 through 10, and 15 and 16

Jan 1, 1955

By G. St. J. Perrott

A study of certain fundamental characteristics of liquid-oxygen explosives has been made. A discussion is given of the factors affecting the life of the cartridge and the relation between explosive strength and oxygen content. The explosive properties of L.O.X. cartridges packed with a variety of lampblacks, gas blacks, and other materials have been experimentally determined by means of the ballistic pendulum, Bichel gage, and measurement of the rate of detonation. DURING the past year, the Bureau of Mines has carried on an investigation of liquid-oxygen explosives (L.O.X.) to supplement the work described in previous publications.' The present paper gives results of the first part of this work, which was a laboratory investigation of the properties of typical combustibles used in L.O.X., and the relation of these properties to the absorption and retention of oxygen by the explosives and their explosive characteristics. No attempt will be made to describe the development of liquid-oxygen explosives, because this phase of the subject has been well covered. The L.O.X. cartridge consists of a paper wrapper filled with an absorbent combustible material that is saturated with liquid oxygen by soaking it therein. After saturation, the cartridge is removed from the liquid and fired with fuse and cap, or electric detonator, in a manner

Jan 12, 1924

By N. P. Peterson

The Castle Dome copper deposit is of the porphyry type and occurs in a body of quartz monzonite intruded into the pre-Cambrian formations and possibly into the lower part of Paleozoic limestones. The hypogene sulphide minerals include pyrite, chalcopyrite, and a little molybdenite, sphalerite, and galena. Pyrite and chalcopyrite are disseminated or occur in small closely spaced veins. The hypogene mineralization shows distinct zoning in the distribution of pyrite and chalcopyrite, so that the mineralized area can be subdivided into pyritc and chalcopyrite zones. Supergene enrichment, though not extensive, played an important part in the formation of the ore body, the chalcopyritc zone being the pro-tore. Several thin, gently dipping, diabase sills occur in the mineralized area, and the copper content of the rock in and near these sills is substantially higher than average. The formation of the ore body was caused by the combined effects of three forces: I. Zoning of the hypogene mineralization, 2. Richer copper metallization associated with the diabase sills, and 3. Supergene enrichment. Introduction The Castle Dome copper deposit is about 5 miles west of Miami, Arizona, and about 3 miles west of the Miami-Inspiration ore body. The Castle Dome open-pit mine is on the south flank of Porphyry Mountain, a prominent landmark of the region. In 1941 the deposit was being explored by the Miami Copper Co., but the exploration program was cut short when the decision was made to develop the property as a war project. The Castle Dome Copper Co., Inc., was organized as a wholly owned subsidiary of the Miami Copper Co., and arrangements were made with Defense Plant Corp. for developing and equipping the mine and for construction of a concentrating plant. Construction and development work was begun in January 1942, and milling operations started June so, 1943. Since that date, the mine has been in continuous operation by the Castle Dome Copper Co, under a lease agreement with Defense Plant Corp. producing copper at an average rate of 4,000,000 lb per month. To January I, 1946 the total production amounted to 121,088,000 lb of copper,4,271 oz of gold, and 211,755 oz of silver. A detailed study of the copper deposit and the surrounding area was undertaken by the U. S. Geological Survey in June 1943. Other members of the Survey participating in the work were C. M. Gilbert, G. L. Quick, and J. P. Albers. The results of this work will be published as a comprehensive report by the Geological Survey. General Geology The Globe quadrangle, which includes the Castle Dome area, was studied by F. L. Ransome1 of the Geological Survey in 1901 and 1902. His maps and descriptions were

Jan 1, 1949

By F. E. Buch

THE Smelter is designed for a production capacity of 10,000 short tons of blister copper per month, when operating on the present concentrate grade. The Smelter lay-out is shown in Fig I. The major units of equipment comprise two reverberatory furnaces, three 13 by 30 ft Peirce-Smith converters, two straight line casting machines, one being served by a 13 by 30 ft holding furnace and the other by a ladle tilting quadrant, two converter ,aisle cranes and two converter blowers. The plant is compact and the general arrangement of standard gauge railway tracks and conveyor belts provides for a smooth flow of incoming materials and metallurgical products. Concentrate is received by conveyor belts and fluxes in standard railway trucks. The local track system is covered by an electric trolley locomotive. The Smelter treats a wet (10 pct moisture) flotation concentrate containing approximately 53 pct total copper and 0.9 pct oxide copper. The predominating minerals are chalcocite, chalcopyrite and bornite accompanied by small quantities of malachite and cuprite. The gangue is highly siliceous and requires limerock as a flux. Metallurgy would be straightforward were it not for the necessity for eliminating k bismuth which occurs as an impurity in the ore along with the copper. Directly or indirectly most of the Smelter problems can be traced to the necessity for bismuth removal. Copper recovery, based on new copper treated, averages 97.5 pct. GENERAL DESCRIPTION Flotation concentrate, containing to pct moisture, is conveyed from the filter plant to the smelter storage bins by conveyor belts, the material being weighed in transit by a revolving drum type of weigh-hopper manufactured by Samuel Denison and Son, Ltd. The weigher consists of a steel drum with dished ends carried on a horizontal shaft and rotated by an 8 hp squirrel-cage motor through a worm and spur reduction gear. A feed mouth in the drum permits of filling and discharging. The whole unit is supported on a framework resting on weighing levers, which in turn connect to transfer levers, thence to an indicator of the steelyard type situated 16 ft from the centre line of the drum. The indicator is of the "Denison" patent equilibrium controlled ticket stamping type, insuring mistake-proof records by a combination of electrical and mechanical movements which prevent the operator from printing until the cover enclosing the steelyard is closed and until the poise-weights have been set correctly to the weight of the hopper and contents. The machine is capable of weighing 30 short tons at a time but the usual load is 28 tons. After obtaining the gross weight the drum is rotated and discharged into a receiving bin situated below it. The empty drum is weighed and the net weight re-

Jan 1, 1947

By Samuel S. Wyer

Magnitude and Econonmic Importance THE magnitude and economic importance of the problem of correctly valuing natural-gas leaseholds become evident when we consider that: (a) Natural gas is handled in 55 per cent. of the gas distributing plants in the United States. (b) Present known natural-gas acreage forms 47 per cent. of the total known mineral-land acreage in the United States. (c) Five acres of land are now required to protect and maintain continuous service to each of the 2,000,000 domestic natural-gas consumers in the United States. (d) The cost of acquiring and maintaining this acreage of an expendible resource represents a substantial part of the cost of the natural-gas service to the consumer. (e) "The right of a citizen by means of his ownership of or his mining leases on land to draw gas from beneath its surface is property and sometimes valuable property."1 A large number of other court decisions have established the basic legal principle that the right to drill for gas within a given area constitutes an interest in the land itself, and is necessarily an exclusive property right.

Jan 4, 1916

By J. Blodget Britton

DURING the last three or four years I have had occasion to examine, chemically, various samples of matter commonly called flue-dust or cinder, found deposited in the flues and hot-blast chambers and under the boilers of blast furnaces, and also in the flues and under the boilers of puddling and boiling furnaces. Recently several of these examinations were made quite in detail, and as the results reveal, I believe, information of no inconsiderable importance, I am induced to communicate them to this Institute. A sample of deposit obtained from the flues of one of the blast furnaces at the works of the Phoenix Iron Company, at Phoenixville, Pa., was found to have the composition given in Column I of the following table

Jan 1, 1877

By Walter Miller

Any review of the engineering progress made in 1932 in the petroleum refining industry must necessarily be broad and general, improvements having been made in practically all major branches of this activity. Several factors contributed to an advancement on a wide front, much of it coming from those active in refining, considerable from those not, immediately in it but engaged in designing and installing equipment and maintaining large and capable staffs of experts in both engineering and development work. Another factor has been the ability of the refiner, because of less than capacity operation, to carry on experimental and development work in regular plant equipment. The movement to higher antiknock value gasoline has continued through 1932, and the average improvement of the more widely sold branded gasolines is from 3 to 4 points higher in the octane scale. A very great improvement was brought about during the year in the method of determining the octane number of gasoline. While the procedure and equipment for determining this value as developed by the Cooperative Fuel &search Steering Committee prior to 1932 had received fairly general acceptance, evidence that it did not always evaluate in a measure consistent with road performance quickly accumulated, and led to further effort to synchronize laboratory results with actual use. As the result of some really brilliant work on the part of the C.F.R. Committee and a large number of collaborators, it was found that a comparatively minor modification of the previously developed equipment and method gave surprisingly concordant results between laboratory tests and trial per-formance on the road. This method has been officially accepted by the Society of Automotive Engineers and the American Petroleum Institute, and will according to present plans go into general use on April 1, 1933. The American Society for Testing Materials has studied the method but at the time of writing this had not reached a final decision regarding it. Improved Volatility of Gasoline The most notable trend during the year, in addition to a very considerable increase in antiknock value referred to above, has been in the

Jan 1, 1933

By Irving Hale

The superiority of electric power for mining purposes was recognized in a general way as soon as the electric motor be-

Jan 1, 1897

By Gordon H. Chambers

MANGANESE ore is a true jack-of-all trades among industrial minerals, its only possible rival being iron ore. It is used in porcelain enamel, dry batteries, building brick, glazed pottery, floor tile, plastics, welding rods, chemicals, and varnish. You may be reading this through spectacles decolorized with manganese, and the light bulb above you contains some of this element. GEOLOGY Nearly all commercial manganese oxide deposits are of secondary origin; that is, they are concentrated by weathering from other manganese minerals more sparsely distributed in veins. The oxide minerals usually form irregular masses but in some places (Russia) they occur as beds of varying thickness and purity. Some manganese oxide bodies occur in soft gravel or clay formations but in other places the minerals are found in the form of veins and rounded nodules in limestone and other hard rocks. The geologic features of manganese deposits closely resemble those of iron deposits. Classification of the deposits is shown in the following table: I. Classification of manganese deposits based upon form of occurrence A. Stratiform masses 1. Oxides interlayered with sediments or layered volcanic or metamorphic rocks 2. Carbonates or silicates interlayered with sediments or layered volcanic or metamorphic rocks 3. Oxides, as surface bog deposits B. Veins and breccia filling 1. Oxides in larger part 2. Carbonates or silicates partly weathered to oxides C. Irregular masses 1. Oxides 2. Carbonates or silicates largely weathered to oxides D. Aggregates of small oxides in clay or weathered rocks 1. Mainly oxides E. Unclassified deposits II Classification of manganese deposits based upon mode of origin A. Hydrothermal deposits

Jan 1, 1949

By A. C. Watts

For several years, a mine in Colorado experienced considerable trouble from small fires caused by the blasting of coal. Although a well-known make of permissible powder was used, it was first thought that the powder ignited gas that might be present and that this, in turn, set fire to line brattices or to the coal. Experiments were, therefore, conducted with another make of powder, but the results convinced the superintendent of the mine, Robt. Williams, Jr., that the fires were not caused by the powder but by the high-voltage electric current used for detonating the shots. The mine "makes" gas very freely, giving off from three-fourths to one million cubic feet of methane every 24 hours. The coal is a good grade bituminous of a very free burning quality. Electric shot-firing from the outside, after all men and animals were outside, had been practiced for a number of years. The shooting circuit was connected with the main power circuit at the mouth of each entry. Shooting circuit switches were mounted in boxes, which were kept locked with the handle of the switch, in open position, showing through the bottom of the box. The door of the box could not be shut and locked when the shooting switch was closed. At the entrance to each room, or working place, a small switch, called the miner's switch, was placed on the shooting line. It was the duty of the miner, when entering his place at the beginning of the shift, to see that this switch was open and that it was kept open until he left the placc at the end of the shift to go out of the mine. Grounded return was used for main power lines. The current was 500 volts, direct current, with 100 to 300 amp. The nearest working face was 9600 ft, from the shot-firers' switch outside the mine and the most remote working face was 2½ miles. The various working faces were scattered over a wide area between these two points. A description of the main power line would be valueless; the conductors were of sufficient size, the drop in voltage being not more than

Jan 1, 1927

By H. B. Goodrich

In considering historically oil development in Oklahoma, it must be recognized that basic evolutionary factors interlock and have an effect in common throughout the whole oil industry, regardless of locality or minor problems. Oklahoma, as the third in rank of oil-producing states (Texas being first and California second in production for 1929) has, like the rest, advanced to at least a partial recognition of the words, "Conservation," "Unitization," "Curtailment," "Prora-tion," and especially "Cooperation." Whether through altruism (of which there have been examples) or by exercise of good business common sense, Oklahoma operators realize that the oil business can run itself by cooperative action for the good of all. In this long-continued period of overproduction, Oklahoma has brought the advancing output down to limit of market requirements at least temporarily. Sources of Statistical Data For this paper, figures published by four recognized authorities were consulted. Between themselves these vary only a negligible per cent, in their totals. To be consistent, and on account of earlier availability the estimates published by the Oil and Gas Journal are mainly used herein, supplemented from other public and private sources. General Oil ProdCction in Oklahoma In 1927 Oklahoma's peak of all years was 276,022,024 barrels. In 1928 Oklahoma's total production was 247,500,851 barrels. In 1929 Oklahoma's total production was 252,229,474 barrels. The efforts of proration and curtailment programs on flush and semi-flush districts such as Greater Seminole, Oklahoma City, Logan County and others, with the natural decline of older pools, kept 1929 below 1927, but still the total was greater than in 1928. The total United States production for 1929 is herein taken as estiiated at 1,004,266,723 bbl.† Oklahoma produced 25.1 per cent. Of

Jan 1, 1930

By H. W. Hardinge

Disregarding for the present the economic side of a new device, let us turn to that feature of the conical pebble-mill which is of interest from a scientific point of view, and consider the device as a puzzle in which the theories of the cylindrical type of mill have been increased. Many articles have been written on the theory of the tube-mill, and explanations have been made which do not explain ; but these have evolved suggestions of practice which have resulted in changes in the tube as to length, diameter, feed, discharge, speed of rotation, rotation on hollow trunnions, rotation on rings, and changes in the operation as to quantity and size of pebbles, charge of load above or below the axis, crushing by causing the larger pieces of the material of the charge to act as grinders, whether crushing is abrasive or impactive, etc. The practical worker in crushing. is first interested in the endeavor to reach an econonlic means of accomplishing a desired end; but the improvements in crushing-practice have been largely left to the manufacturer of machinery, who, as a rule, has little, if any, knowledge of the specific requirements— such as granulation, sizing for concentration without pulverizing the metals, instead of pulverizing the rock or gangue; the metals being the more friable, while the rock is tough and not so easily disintegrated. A reversal of this practice is the aim of sliming direct for cyanidation or pulverizing for cement, etc. In the ordinary cylindrical mill, having a diameter of 4 or

Jan 1, 1909

By Waldemar Lindgren

I. INTRODUCTION AT the time of the discovery of America the old world had a scant supply-of the precious metals. Both the northern and the southern part of the new continent proved wonderfully rich in gold and silver and its treasures were eagerly looted; though the looting has lasted four centuries, the nines of its mountain chains are far from being exhausted. Even the later discoveries in Australasia and eastern Siberia could not rob the Western Hemisphere of its position as the greatest gold and silver producing region of the world, though finally the developments in a narrow and circumscribed area in South Africa wrested from the Americas their supremacy in the production of gold. Nevertheless the history of the two parts of the great western continent has been strikingly different. At first the Spaniards extracted vast treasures of silver from Mexico, Peru, and Bolivia, while Colombia and some placer deposits in Peru yielded a smaller quantity of gold. A couple of centuries later, a stream of gold began to flow from Brazil, the silver production from the countries mentioned above continuing strong in the meanwhile. Later on, the yield of South America diminished, but to offset this there began a wonderful series of discoveries in North America. The gold fields of California astonished the world; and when the cream of these had been skimmed off there began a no less amazing development of the Central Cordilleran gold and silver districts, which soon wade the United States the greatest producer of the precious metals. Aided by ever improving technique, extensive exploration, and a system of railroads, the yield was maintained and increased. Still later followed the discoveries of the gold fields of the arctic region and silenced those who had maintained that the zenith in gold production had passed. Recently the province of Ontario in eastern Canada

Jan 4, 1916

By J. Randel Hill

The 64th Texas Legislature passed the "Texas Surface Mining and Reclamation Act," Chapter 131, Texas Natural Resources Code (subsequently referred to as "the Act"), at a point in time when little surface mining had taken place within the state. Thus, enactment of regulatory control governing mining operations in our state has, for the most part, preceded widespread, intensive mining activity. I should point out that the statute applies only to the extraction of coal, lignite, uranium and uranium ore. A recent opinion rendered by the Attorney General's office has stated that extraction of the named elements, when it occurs incidental to the extraction of other materials, e.g., clay, is not not an activity subject to the Act. An important theme of the Act, frequently overlooked in other environmentally oriented legislation, is recognition of the Act's affect on the mining industry. The Act states that "the extraction of minerals by surface mining operations is a basic and essential activity making an important contribution to the economic well-being of the state and nation" and, in reference to reclamation being accomplished contemporaneously with mining, provides a recognition that "the extraction of minerals by responsible mining operations is an essential and beneficial economic activity." This legislative recognition is, of course balanced against the need for proper mined land reclamation, the rights of surface owners, the need to guard against unreasonable degradation to land and water resources and numerous other actions or events that the Legislature wanted protected. Another rather pervasive general theme that is established in the Act is the concept that the agency is entitled to obtain whatever information, or take whatever action, that appears reasonably necessary to effectuate the purposes of the Act. This concept, coupled with the detailed requirements placed on mining operations in the portions of the Act dealing with Permit Applications, Reclamation Plan and Reclamation Standards, easily insures that surface mining activities can and will be regulated to the extent necessary. Section 131.102(b)(2) is probably the most relevant provision in the Act which deals with the preclusion of mined lands becoming waste lands. This portion of the Act states that the surface mining operator shall: ". . . restore the land affected to the same or a substantially beneficial condition. ." In this language the Legislature had made it abundantly clear that the abandoned or orphaned lands found in some of the Eastern states, will not be tolerated in this State, and provided the Commission with a degree of latitude to determine what condition would be appropriate in each individual mining situation. I bring this area of the Act to your attention because it is the area which has received the most inquiries and concern by operators, i.e. what does "substantially beneficial" constitute? The Commission's staff has spent a considerable amount of time wrestling with the statutory language "substantially beneficial" to determine the legislative intent and provide operators with guidance of what they can expect. In this regard, the most definitive criteria in our opinion lies in the Act's legislative hsitory. The Legislature had before it basically three reclamation standards namely: House Bill 656, considered to provide the most stringent reclamation standard and identical to Senate Bill 66; House Bill 1717 which was supported by industry spokesmen and was considered to contain the least stringent reclamation standard; and Senate Bill 55 which was adopted by the Legislature. During the Bill's initial hearing before the House Environmental Affairs Committee, the House sponsor of the Senate Bill 55, which was the Bill eventually adopted, made the following statement: (I am quoting verbatim from the Committee's transcript although substituting the speaker's reference to the authors names with the Bill's numbers.) "An example of the differing approaches of the four bills can be seen in the area of reclamation standards and this is critical. House Bill 656, talking about restoring the surface of the land, House Bill 656 has this statement: 'At least fully capable of supporting the use to which it was capable of supporting prior to any mining or any higher or better use.' In other words you have to restore it to the level it was prior to the mining. Senate Bill 55: 'Restore the land to the same or substantially beneficial use.' Substantially beneficial use. (Emphasis his) House Bill 1717 says: 'Restore insofar as practical to appropriate beneficial post-mining use.' So that House Bill 1717 said to, 'restore insofar as practical to appropriate beneficial use. I think that's too weak, whereas I think the House Bill 656 that would call you to restore it to at least the use it had prior to the mining may also be too tight the other way. I think the Senate Bill 55 approach is down the middle of the road which says that you do restore it to the 'same or substantially beneficial use,' is a proper way to go there." Therefore, the conclusion that we have drawn from the legislative history of the bill is that the extent of reclamation required by "substantially beneficial" may be something other than the use it was prior to

Jan 1, 1979

By H. Foster Bain

Probably no more significant change has come into the lives of men in the past two hundred years than their shift from major dependence on plants and animals to major dependence on minerals. From the dawn of history, nay from long before that dawn, food and clothing had been man's main concern. The wandering of the tribes in pastoral ages was in search of grass for their cattle; the patient work of the "man with the hoe" has ever been to supply food for himself and family and if he accomplished so much he had little strength, energy, or ambition for other things. The great civilizations of the past arose in the fertile valleys where food supply was abundant or on shores where by grace of the wind and primitive wooden ships food could, if needed, be imported. Provision for the "seven lean years" by storing the abundance of the seven fat years was long held up as the highest example of statesmanship and the ambitions of the Roman populace did not go beyond bread and circuses, the former the product of a plant and the latter involving essentially contests of men and other animals. Through all those centuries of want, misery, and warfare it was, for example, an axiom that "an army fights oh its belly." Now an army rides to the battle line in trucks; its members stand up and fight with tons and tons of metal and other minerals. Food supply is assumed, and rightly so, for in this modern world of ours shortage of food is chargeable at once to poor organization or deficiency of transport. The areas in which famines occur are those in which the one or the other

Jan 1, 1932

By D. U. Deere, F. D. Patton

Introduction A close relationship exists between the geologic investigation and the stability analysis of the slopes of an open pit mine. One significant result of this relationship is that the stability analysis is no better than the assessment of pertinent geologic factors that enter into the analysis. In some slope stability problems the engineering solution becomes obvious once the geologic framework is established. In other cases, establishing the geologic framework is only the first stage in the process of analysis. However, even in these cases the geology should not be neglected once the analysis is made. The geology should be periodically reviewed when new slopes are excavated. This will help ensure that the basic assumptions for the analysis have not changed and will permit changes when new conditions are encountered. In recent years improved methods of stability analysis have been accompanied by advances in laboratory testing techniques and new knowledge of the shear strength of rock discontinuities. At the same time there have been improvements in field geological descriptions. As more experience is gained in analyzing and predicting the stability of rock slopes, the importance of certain geologic factors has become more apparent. Some of these factors were described in a paper given at the Open Pit Mining Symposium in Johannesburg, South Africa in September 1970 (I). This paper includes many of the points covered at that meeting but with additional emphasis on the significance of the major geologic structures. Other papers given at the South African symposium also considered geological and hydrogeological factors in slope stability analysis (2) (3) (4) (5) (6). This paper first describes the approach to a slope stability problem including assessment of the relative roles of field geology studies, laboratory testing, stability analyses, and continued slope monitoring studies. Next, is described a framework which has been found useful for classifying or separating the several types of slope stability problems encountered in open pit mines. The principal geologic factors in slope stability problems in rock are discussed and brief comments are made on how these factors distinguish stability problems in rock slopes from those normally encountered in soil slopes. The over-riding control of major geologic structures, especially faults, in most slope stability problems is emphasized. In this regard the relative importance of statistical studies is contrasted with knowledge of the positions of key structural

Jan 1, 1971

By D. D. Lambert, E. C. Simmons

Rare earth element (REE) analyses of cumulus plagioclase from the PGE ore zone of the Stillwater Complex indicate that pressure fluctuations in the magma chamber acting on a single magma cannot be responsible for features such as the reappearance of Mg-rich olivine on the liquidus. The data are more consistent with a model involving multiple injection and mixing of geochemically distinct magmas. The PGE-bearing sulfides of the J-M Reef are associated with such a reappearance of olivine, indicating that the unusual location of the ore zone may be related to the addition of new magma, compositionally distinct from magmas that produced cumulates in the Ultra- mafic zone of the complex.

Jan 1, 1984

Only the coal of the Sunnyside district in Carbon county is coked. Two companies, the Utah Fuel Company and the Columbia Steel Corporation, operating adjoining mines at Sunnyside and Columbia, produce coke. The Utah Fuel Company has 81 9 beehive coke ovens at Sunnyside. Only 350 ovens are being operated at the present time, largely because the smelters which had been using Sunnyside coke changed their equipment from blast furnaces to reverberatory furnaces

Jan 1, 1925