Search Documents

Jan 1, 1939

By H. E. Stauss

THE short-time tensile-strength test, while it has not attained the practical importance of the creep test at elevated temperatures, has the advantage of being rapid and is satisfactory for determining relative strengths. For platinum and its alloys, which frequently are used at high temperatures under ill-defined conditions, the short-time test provides useful data that aid in the selection of the most promising alloy for each use. Measurements have been made upon 13 alloys, using wire 0.0031 in. in diameter, the choice of alloys and of wire size being determined by the requirements of a practical problem. Later the measurements were extended to higher temperatures by the use of heavier wire, 0.010 in, in diameter. APPARATUS The use of fine wire made the necessary equipment very simple, since no effort was made to measure the elongation. A small platinum-wound horizontal furnace was used, ½ in. in internal diameter by 1 ft. long, with the wire threaded through it. The wire, clamped at one end while the other ran over a ball-bearing pulley, of a total length of 29 in., was loaded directly by running sea sand into an attached basket, making the rate of loading and not of elongation constant. The sand flowed from a funnel, under a head of 3 in., into the basket. 3 in. below the orifice, at the rate of 170 grants per minute. Pulley friction and bending resist-ance of the wire as well as the force of impact of the sand could be neg-lected, being 3 grams and 0.5 grams, respectively. Furnace temperature .was uniform within ±5° C. over a length of 3 in., although a drift with time occurred, the largest amount being 20° C. No provision was necessary for a controlled atmosphere.

Jan 1, 1939

The following list contains the names of members of whose deaths notices have been printed in MINING AND METALLURGY during the year ending April 1, 1939. Biographical sketches published in MINING AND METALLURGY are indicated in the last two columns.

Jan 1, 1939

By Joseph M. Dawson

Although eight new fields were discovered along the south central fault-line district of Texas during 1938, only one can be considered as of major importance. and as a whole the year was one of no very great development. Several prospects, particularly two, were condemned through drilling, which had been considered important for probable Edwards limestone production. The oil produced was approximately the same as during 1937; namely, about 9 million harrels. This, of course, does not represent potential production but that allowed under proration. The year witnessed the very rapid decline of operations and interest in Austin chalk production. It has been found that only in rare instances mill chalk production pay for itself, because the wells decline extremely rapidly and the recovery per acre, formerly estimated at 2500 bbl., is now considered to he around 1000 barrels. There was an intent interest in the drilling arid producing of edge and abandoned properties in the three Edwards lime producing fields; namely, Luling, Salt Flat and Darst Creek. Many good wells were completed on properties formerly considered below the water level or produced beyond the economic limit The Edwards is penetrated only a few inches and a very small charge of acid is used. The results have been surprisingly

Jan 1, 1939

By A. J. M. Ross

BACKFILLING of stopes and other underground openings in the Homestake mine with sand tailings was undertaken primarily to reduce surface subsidence, which was wrecking much of the surface plant and a substantial part of the town, and to make possible maintenance of open-ings into the top of pillar stopes as mining progressed. The progress of this type of filling has been rapid and the results very satisfactory. Sand is now used in filling timbered stopes, shrinkage stopes, and abandoned drifts and crosscuts. A permanent pipe-line system for transporting sand tailings into the mine by gravity has been installed. The close filling of all stopes has resulted in important benefits other than the two major ones. The ore bodies in the Homestake mine occur as replacements in one distinctive layer of the metamorphosed pre-Cambrian sediments along a group of minor folds that together form a complex anticline that pitches at 35° to 40° to the southeast. The ore bodies are extraordinary for their magnitude. Widths of over 300 ft. have been mined and continuous ore has been followed for over 1200 ft. along the strike on some of the upper levels. Mining has been by shrinkage stoping with square-set mining of crowns and pillars. In the standard plan, shrinkage stopes 60 ft. in the direction of strike and the full width of the ore have been taken up to within 25 ft. of the level above. After filling, the crown has been mined by square-set methods, as have also the 40-ft. pillars between shrinkage stopes. In former days, when the supply of ore seemed inexhaustible, the mining of pillars was allowed to lag far behind because of the high cost. Many pillars were rather badly fractured on the level and in some places between levels. Coarse waste was used for backfilling all stopes, but in pillars it became increasingly difficult to maintain haulageways for the transporta-tion of this fill over the top of the stopes as mining progressed. The cost of maintaining these crosscuts was excessive and in many pillars prac-tically impossible. Therefore it became the practice to fill pillar stopes by tapping the back and sides of the stopes.

Jan 1, 1939

By E. V. Foran

Among the many newer disclosures that have accompanied the petroleum industry's progressively deeper exploratory drilling is the increased frequency with which the operators are encountering reservoirs of which the products at the time of discovery exist wholly or predominantly in the gas phase. The popular term "distillate pool" is most often used within the industry when referring to this type of reservoir, and in this paper the term is used in that sense. These pools have been observed in many different surroundings. In some places the entire reservoir is filled with the wet gas containing its water-white condensible products in the gas phase but apparently with no dark oil or other hydrocarbon liquids in the reservoir. The 8200-ft. horizon in the Big Lake field in West Texas is a good example of this type. At other places the wet, or distillate-bearing, gas may form a large gas cap directly overlying and in contact with an extensive reserve of dark oil. Oklahoma City, Kettleman Hills, the 8500-ft. horizon in the Big Lake field, and many others are examples of this type. There are also many places in which the wet distillate-bearing gas fills nearly the entire reservoir space, while the dark oil occupies only a narrow, bandlike zone, which marks the boundary of the reservoir along its lowest productive contour. The heavier components of these deep pool gases are generally water white in color, a large portion of which are condensible in a conventional oil and gas separator, when operated under pressures of the order of 400 to 800 Ib. per sq. in. Although the water-white products recovered in the separator sometimes have end points of 650" F. and higher on standard Engler distillation, they occur only in the gas phase in the reservoir. It is entirely possible that even some small amounts of dark colored reservoir components may occur in the gas phase when the temperature is 300" F. and pressures exceed 6000 Ib. per sq. in. Close approaches to these conditions have been encountered in the deepest producing wells. The condensible content of the deep reservoir gases of the many pools that have been tested or produced to date shows a wide variation in both condensible content, per 1000 cu. ft. of gas, and physical character.

Jan 1, 1939

By Allen Garrison

IT is the purpose of this article to present. the results of an investiga-tion of certain clay and shale suspensions having viscosities that are materially influenced by fluid motion, and to discuss the bearing of these results, upon the choice of policy in the control of drilling fluids. A previous article described the design and the characteristics of an instru-ment adapted to measure the viscosity of plastic suspensions during continuous uniform motion and at a variety of speeds.1 It has long been recognized that the viscosity of a clay suspension depends on the past history of the fluid motion. Since an abundance of literature is available on this phenomenon,2 it is not necessary to describe it in more than general terms. It is usually observed that rapid motion reduces the viscosity of a clay suspension, and that some time is required for the viscosity to fall to its equilibrium value after the steady motion is started. On reducing the speed of motion to some lower value, the viscosity again rises, but it also requires some time to attain a steady viscosity value at the slower rate of motion. Thus clay suspensions are usually observed to be increasing in viscosity as time passes when the measurement has been immediately preceded by fluid motion that was more rapid than that employed in the measurement. And it is usually observed that the viscosity falls as time passes when the measurement has been preceded by more quiescent conditions. Reed,3 and Broughton and Hand4 have reported a condition of observa-tion of clay suspensions in which the viscosity was observed to fall during the first few moments of steady motion, and rise thereafter. The characteristics of the new instrument are particularly well adapted to studies of this kind. With it we have been able to observe all of the phenomena described above, and it is important to understand their nature because they all occur at some time during normal drill-

Jan 1, 1939

By T. B. Counselman

AFTER several years study, the Universal Atlas Cement Co. decided to rebuild its plant at Leeds, Alabama. The entire old plant, which was to operate during the new construction, was then to be scrapped with the exception of two kilns. The quarry was to be mechanized, new and larger kilns installed, with the most modern type of equipment all through the plant. Raw grinding operations at all of the Universal Atlas plants were dry. However, the dust hazard of this operation and the growing emphasis on occupational diseases made wet grinding attractive. Coal at Leeds is cheap, so that a slightly higher coal practice was unimportant. Power was cheap, so that waste-heat boilers were not desirable. Since new kilns were to be installed, these could be made long enough to make filters unnecessary. Wet raw grinding could be either the old practice of open-circuit compartment mills or closed-circuit grinding in accordance with metal-lurgical practice. The latter saved power and steel wear and saved initial investment. This had been demonstrated in cement plants. Also, the elimination of tramp oversize was a most important advantage. Ease of chemical control was another factor. Blending in the thickener, with elimination of slurry mixers had been found practicable. Therefore, if wet raw grinding were used at all, the advantages were clearly in favor of closed-circuit grinding. Detailed layouts of the most modern possible closed-circuit dry-grinding plant and of a closed-circuit wet-grinding plant were prepared, and careful estimates were made of initial invest-ment and operating costs. Full consideration of all the factors involved resulted in a decision to install wet closed-circuit grinding.

Jan 1, 1939

By T. B. Counselman

AFTER several years study, the Universal Atlas Cement Co. decided to rebuild its plant at Leeds, Alabama. The entire old plant, which was to operate during the new construction, was then to be scrapped with the exception of two kilns. The quarry was to be mechanized, new and larger kilns installed, with the most modern type of equipment all through the plant. Raw grinding operations at all of the Universal Atlas plants were dry. However, the dust hazard of this operation and the growing emphasis on occupational diseases made wet grinding attractive. Coal at Leeds is cheap, so that a slightly higher coal practice was unimportant. Power was cheap, so that waste-heat boilers were not desirable. Since new kilns were to be installed, these could be made long enough to make filters unnecessary. Wet raw grinding could be either the old practice of open-circuit compartment mills or closed-circuit grinding in accordance with metallurgical practice. The latter saved power and steel wear and saved initial investment. This had been demonstrated in cement plants. Also, the elimination of tramp oversize was a most important advantage. Ease of chemical control was another factor. Blending in the thickener, with elimination of slurry mixers had been found practicable. Therefore, if wet raw grinding were used at all, the advantages were clearly in favor of closed-circuit grinding. Detailed layouts of the most modern possible closed-circuit dry-grinding plant and of a closed-circuit wet-grinding plant were prepared, and careful estimates were made of initial investment and operating costs. Full consideration of all the factors involved resulted in a decision to install wet closed-circuit grinding. The capacity of the new kilns was established at 4000 bbl. per day. Two new kilns were installed, each with a capacity of 80 bbl. per hour. Since 625 lb. of raw material is required to make a barrel of finished cement, the capacity of the grinding plant for the new kilns had to average only 1250 tons per day. Sufficient additional grinding capacity had to be provided for the two remaining old kilns, or their possible replacement by a third new kiln. The grinding rate, therefore, was set at 90 tons per

Jan 1, 1939

Jan 1, 1939

By AIME AIME

JOHN HUNTER NEAD, chief metallurgist of the Inland Steel Co., Chairman of the Iron and Steel Division for 1939, a native of Missouri and graduate of the University of Michigan, first taught chemistry after graduating from college and then decided to follow the field of his college specialization and be a metallurgist. In succession he was associated with the H. H. Franklin Co., Syracuse, N. Y., the Watertown Arsenal, the Racine Steel Castings Co., and the Minneapolis Steel and Machinery Co. During the World War he held a commission as Captain in the Ordnance Department and served both overseas and on the technical staff in Washington. Returning to civilian life, Hunter Nead was research metallurgist and then chief metallurgist of the American Rolling Mill Co. from 1919 until 1931, when he went to his present position with Inland.

Jan 1, 1939

By C. M. White

CITIZENSHIP is a rather abstract subject on which a great deal could be said-a subject on which a great deal is said -and still one which too many of us seldom think about and seldom work at. Too many of us engineers and business men have but a vague idea of citizenship. We think that if we go to the polls on election day and obey the laws scrupulously, with the exception of an occasional traffic violation, we are pretty good citizens and are doing our duty by our city, state, and nation. But when you think it over, that's a very passive observance of the important right of counting oneself a citizen of a country. There is nothing very positive in that attitude. There is nothing that indicates that we have sufficient interest to really go out and do a job for the -welfare of our country, forgetting any personal advantages or inconveniences that might arise. In other words, this type of voting-on-election- day, law-abiding citizenship does not keep us awake a single minute; it does not take any particular thought or require the expenditure of any time or energy.

Jan 1, 1939

By Hans Lundberq

WHEN geophysical methods were first employed in the search for ore deposits and oil accumulations, it was hoped that they would provide a direct means of locating such concentrations. Magnetized needles were used long ago in prospecting for magnetic iron ore, and soon after the discovery of galvanism in about 1790 attempts were made to find concentrations of valuable minerals electrically. Evidence indicating that the early geophyeical instruments were regarded merely as improved divining or dowsing rods is to be seen in the names "mineral finders," "ore finders," etc., that were applied to them. Today, appellations of this kind raise serious doubts in informed minds as to the intelligence and integrity of individuals advocating the use of such euphemistically named methods or instruments, for experience and research have shown that, geophysical, it is never a question of directly locating a given mineral but merely of delimiting its possible occurrence.

Jan 1, 1939

By Ralph Hultgren

FEW phase diagrams of alloys composed of two transition metals have been adequately studied, probably because of the high melting points involved. Transition metals are the elements that have inner shells incompletely filled with electrons. They comprise groups IIIa to Villa of the periodic table, including more than half of all metals. We have chosen to study two systems whose comparatively low melting points allowed the alloys to be melted in a molybdenum resistance furnace. The nickel-palladium system proved to consist of a simple series of solid solutions, but iron-palladium manifested several remarkable features. The main characteristics of the latter diagram were decisively established, but lack of time prevented precise determination of phase boundaries. The gamma to alpha transformation in this system is unusual and warrants further study. Grigorjew1 determined the liquidus and solidus of the iron-palladium system by thermal methods. He found a minimum melting point, but no eutectic. He also found that palladium lowered the gamma to alpha and raised the gamma to delta transformation temperatures of iron, with a complete series of solid solutions existing between gamma iron and palladium. His measurements also indicated a compound or super-lattice near the composition FePd3. Jellinghaus2 found that annealing at 500° C. greatly increased the magnetic coercive force of an alloy of composition FePd. X-ray dif-fraction photographs showed that a tetragonal ordered phase had formed during the anneal.

Jan 1, 1939

By AIME AIME

Jan 1, 1939

By W. D. Haselton, J. B. Newsom

SAFER, cheaper, and faster sinking of mine openings seems to have been realized with the completion of a borehole 5 ½ ft. in diameter and 1208 ft. deep, in Minnesota, during 1938. Moreover, as the opening is to be used solely for ventilation, its circular cross section, smooth walls and freedom from fire hazard recommend it in comparison with the usual timbered shafts of rectilinear cross section. It should be pointed out that a drill hole sunk without the use of explosives frequently will stand open without support, whereas a shaft sunk by standard procedure using dynamite usually must be timbered because of the wall-shattering effect of explosives. The saving in maintenance resulting from the elimination of timber is obvious. The work was done by Pickands Mather & Co. at its Zenith mine, Ely, Minn. This company wanted a ventilation opening capable of delivering 50,000 cu. ft. of air per minute to the fourteenth level, 1200 ft. below the surface. While several general articles1-3 have described the method used, detailed time and performance records have not been presented before. Moreover, with a method as new as this, it is important to compare the results attained under widely varying conditions. Among the new conditions faced at Ely were some extremely hard rock, a series of vertical fractures, seepage water, and some long stretches of sound rock which, combined with excellent equipment, gave a chance to operate without unusual delays. Developments in boring large holes have generally taken the obvious course of increasing the size of the equipment, a line of attack that has resulted in putting down 3-ft. diameter holes at damsites for studying the foundations4 and in drilling ventilation openings between levels at Butte.5 Such drills operate from the collar of the hole, and the power from the drill is transmitted to the cutting tool through drill rods or pipes. In order to keep down the volume of rock that must be ground to sludge, the cores in large-diameter drilling are made as large in diameter as possible. Their large diameter increases their weight per foot of length, which

Jan 1, 1939

By O. M. Schaus

REDUCED activity of mining, because of the business recession, had the effect of lowering working time, hence of reducing exposure to accidents, so it is probable that 1938 will be found to have had a lesser number (both fatal and nonfatal) though the accident rate may remain about the same as in 1936 and 1937. During periods of re-employment, such as occurred during 1936, 1937, and 1938, the new men entering the industry are less experienced and not as well trained in accident prevention as are the older, more experienced men and are frequently subject to more accidents. This situation should tend to correct itself as the new employees be- come better trained.

Jan 1, 1939

By E. DeGolyer

PROSPECTING for new deposits is a part of the ordinary routine business of the petroleum industry to an extent that is not true for any other mineral industry. The health of the industry depends upon whether we are successful or unsuccessful. How many know what it costs to find oil today and what it has cost in the past? Very few, I will wager. The industry is not well informed upon this extremely important point. We cannot deal in averages for lack of information. Does it cost more or less than previously? Prospect wells are increasingly deeper and, since the introduction of the core drill, prospecting techniques have required increasingly expensive field oper-

Jan 1, 1939

By T. M. Girdler

IN THESE perilous days of world- wide uncertainty, this Institute and the profession represented by it take on new importance in the economic life of the nation. I have long been impressed by the fact that the objects of the A.I.M.E. are purely professional and scientific. The country has benefited from your honorable tradition of adherence to those objectives over a period of 68 years. The Institute's policy of refraining from controversial matters - has made possible the serious, balanced, and uncolored consideration of the particular problems that come before it.

Jan 1, 1939

By AIME AIME

The name and address of the school are given first, followed by the length of the regular undergraduate curriculum, the degree granted, types of courses giben, and the name of the man in charge. This covers only work for the first or Bachelor degree in each case. The following abbreviations are used: B. Bachelor Cer. Ceramic. E. Engineer or Engineering Eng. Engineering or Engineer Geol. Geologist, Geological, or Geology M. Mines or Mining Met. Metallurgy or Metallurgical Mng. Mining Pet. Petroleum Ref. Refining S. Science Tech. Technology or Technical

Jan 1, 1939