Search Documents

By Rosa Palacios, Ángel Ríos, David Velazco

Antamina es un depósito polimetálico de cobre, zinc, plata, plomo, molibdeno y oro ubicado en el departamento de Ancash, Perú, sobre 4,000 m de elevación.Se han perforado más de un millón de metros de sondajes diamantinos, habiéndose identificado 179 variedades litológicas clasificadas según los componentes mineralógicos, tamaño de grano de los granates y grado de brechamiento. Al ser el logueo geológico una actividad subjetiva, basada en la experiencia y habilidad del geólogo, fue necesario establecer un mecanismo de control de calidad del logueo geológico basado en datos objetivos con la finalidad de identificar posibles errores en dicho proceso, para lo cual se evaluó el comportamiento de las diferentes unidades litológicas en relación con las 43 leyes reportadas en los análisis geoquímicos practicados a las muestras de sondajes.

Sep 30, 2022

By E. R. Cole

Laboratory heats of an 80 percent copper high-leaded tin-bronze alloy, similar to Brass and Bronze Ingot Institute (BBII) alloy 3A, were made with reduced tin content to determine whether an alloy comparable to BBII alloy 3A could be produced using less tin to aid in conserving this strategic metal. The tin content was lowered from 10 percent to 8 percent and 5 percent (nominal values), respectively, and the reduction in tin was offset by either increasing the lead content or adding zinc. Mechanical properties, machinability, and corrosion characteristics of the resultant alloys were investigated, and the mechanical properties were compared with BBII typical values and American Society for Testing Materials (ASTM) minimums for high-leaded tin-bronze alloy. Results indicate that the tin content of this alloy could be reduced approximately 1 percent (difference between the 8.4 percent actual tin composition obtained and the 9.3 percent BBII minimum) without seriously affecting the desired properties. Results also show the tin content could be reduced without significantly increasing the chances of rejects for mechanical property failures, which might result from normal variations in the casting process.

Jan 1, 1972

By H. G. Denkhaus

Comment on ?The evaluation of rock brittleness concept on rotary blast hole drills? in the Journal of SAIMM, vol 102. no. 1. pp. 61?66 Comment on ?Correlation of specific energy with rock brittleness concepts on rock cutting? in the Journal of SAIMM, vol 103. no. 3. pp. 163?171by R. Altindag Foreword Some thirty years ago it was almost customary that articles in South African technical and scientific journals were followed up by discussions in which the reader(s) expressed criticism and/or added to the information contained in the article. This custom has obviously died out, be it that the articles are nowadays of such a high standard that nothing can be added or be it that the receivers of the Journal suffer from an information inflation and do not read the articles anymore. I now have the temerity to offer a discussion to an article that recently appeared in the journal, namely ?The evaluation of rock brittleness concept on rotary blast hole drills? by R. Altindag (J.S. Afr. Inst. Min. Metall., vol, 102(2002), pp. 61?66.

Jan 1, 2003

By S. Sarac

In this study, a statistical model is suggested in order to determine the methane emission from a working seam. In the proposed method, methane concentrations which are systematically measured in return airway are the sample values, and the calculated statistical parameter is the upper confidence limit of the average of these values. At any given time, the probability of methane concentration in the return airflow to be lower than the calculated upper confidence limit value is 97.5%. The statistical method has been applied to the panel 206 of Armutcuk Mine, Turkish Hardcoal Enterprises. The calculated methane emission value for the considered shift was 15.18 m3/t.

Jan 1, 2003

By H. Do

In flotation, hydrophobic particles are selectively collected by air bubbles, and the bubble-particle aggregates enter the froth phase. However, less hydrophobic particles drop off from the froth phase, while more hydrophobic particles are recovered. Thus, the froth phase provides an important cleaning mechanism. In the present communication, the froth-phase recovery process has been modeled by considering particle retention times and the carrying capacities of bubbles. The model predictions are compared with the experimental data reported by Seaman et al. (2006). The results show that the froth-phase recovery varies with particle size, particle hydrophobicity, and bubble coarsening.

Jan 1, 2008

This paper highlights the agricultural sector's primary concerns with mining in New Zealand: the information gap, land rehabilitation and compensation. It suggests how these issues can be resolved between the competing land uses in the interests of New Zealand.

Jan 1, 1981

By G. J. de Korte

Dense-medium beneficiation of fine (minus 0.5 mm) coal is not a new concept and has been used in South Africa previously. The dense-medium fine coal plant at Greenside Colliery operated for almost 18 years and, despite proving a difficult plant to operate, did succeed in producing a fine coal product with a low ash content of 7%. No other beneficiation process available could achieve this. Dense-medium beneficiation of fine coal was also used in other countries, of which the plants at Homer City in the USA and Curragh in Australia were the best known. The first application of dense-medium cleaning of fine coal was, however, at the Tertre plant in Belgium1. This plant was built in 1957. About nine years later, a second fine coal dense-medium plant was built at the Winterslag Mine, also in Belgium. According to reports, this plant operated satisfactorily for a period of some 17 years.

Jan 1, 2002

By Porter W. Shimer

(New York Meeting, February, 1912.) IT does not seem to be generally known that some American pig-irons contain notable amounts of vanadium, and while the present investigation is far from covering the whole range of irons, it is hoped that, at least, it may serve to call attention to the importance of looking for this element. The majority of the pig-irons investigated were made in the Lehigh Valley and neighboring furnaces, using more or less New Jersey magnetite in their mixtures. Many of these ores, and probably all of them, contain a little vanadium as well as titanium; the ore from one of the largest of these mines contains 0.05 per cent. of vanadium and 0.60 per cent. of titanium. Dr. Thomas M. Drown was the first to detect the presence. of vanadium in the incrustations 1 occurring on certain pig-irons, and he also found this element in a number of magnetites, but the methods for its accurate determination had not, at that time, been well worked out. In a general way, it may be said that the Lehigh Valley pig-irons contain from 0.02 to 0.05 per cent. of vanadium and from 0.10 to 0.20 per cent. of titanium. These elements follow the silicon; that is, the furnace-conditions which produce a high-silicon, low-sulphur iron will cause the maximum reduction of vanadium and titanium, and the lower grades of iron, with low silicon and high sulphur, have a lower content of these elements. The following analyses of irons made from the same mixture, but under varying furnace-conditions, show this very well Vanadium. Silicon. Sulphur. Per Cent. Per Cent. Per Cent. NO. 1 X, . . . 0.042 3.46 0.022 No. 2 plain, . . 0.038 2.26 0.041 Mottled, . . . 0.0'29 0.52 0.106 1 Robertson and Firmstone, Note Concerning Certain Incrustations on Pig Iron,Trans., xii., 641 (1883-84).

Aug 1, 1912

By D. O. Kennedy

"INTRODUCTION During the recent war attention was directed to prevent the destruction of American industries by sabotage. By Executive order of Lay 19, 1942, the Bureau of Mines was required to conduct investigations and make recommendations that would prevent loss of production of essential war minerals. The Health and Safety Branch of the Bureau of Lines was able to extend its activities with minimum loss of time to include security surveys of the important mineral facilities in the United States.A Mineral Production Security Division was established in the Health and Safety Branch with funds appropriated for that purpose by Congress in April 1942. From July 1942 to July 1945 engineers of this division, under the direction of D. Harrington, Chief, Health and Safety Branch, and J. J. Forbes, Chief, Mineral Production and Security Division, conducted investigations of 1,560 metallic and nonmetallic mines and associated facilities in accordance with the requirements of the Executive order.PURPOSEAn analysis of losses in the production of minerals shows that failure or destruction of equipment either from deliberate or accidental causes produces essentially the same result. Maximum production is insured by the prevention of subversive activities, fires, and industrial accidents."

Sep 1, 1946

By D. Stone

"The Beal Mountain mine near Anaconda, Montana, is an interesting case history of a mine that has continued operations despite several large pit wall failures over a period of approximately 10 years. The largest event involved some 3.9 million tons of rock that has moved steadily at a rate of about 0.05 ft/day since 1992. This paper documents the geotechnical instrumentation and monitoring programs implemented at Beal to provide the company with a comfortable baseline that supported ongoing operations. The success and failure of a variety of stabilization measures will be discussed, along with typical instrumentation responses for several significant events. The success of Beal Mountain serves as a good model for mines faced with serious geotechnical challenges."

Jan 1, 2002

By William D. Klopp, Joseph R. Stephens

Chromium alloys were coated with silicon, alumi-nuw, and boron by pack cementation. None of these simple coatings provided adequate nitridation/oxida-tion protection for a Cr -0.17pct Y alloy substrate as shown by a substantial Increase in the ductile -brittle transition temperature after air exposure for 100 hr at 2100°F. Iron-modified silicide coatings afforded good protection, holding the transition temperature of air-exposed specimens to 350° F compared to 200° F for uncoated unexposed specimens and 800°F for un-coated exposed specimens. Additional attractive cant-binations of modi-tying elements included Fe-mo, Fe-Mo-W, Fe-,Mo-W-Ti, and V-Mo-W-Ti. THE desirability of increased operating tempera-tures as a mcans of improving the performance of ad-vanced air breathing engines has resulted in emphasis on the development of materials with high operating temperature capabilities. Chromium, because of its relatively low density (7.19 g per cu cm), high melt-ing point (3410°F), and adequate strength upon alloy-ing, is a candidate material for turbine buckets and stator vanes of advanced air breathing engines. How-even, chromium is not without severe limitations, the major one being susceptibility to nitrogen embrittle-ment upon exposure to air at high temperatures.1,2 For example, a 25-hr air exposure of a Cr-5 pct W* * All compositions in wt pct. alloy at 2100°F produces a 600°F increase in the duc-tile-brittle transition temperature.' Although dilute alloying with such elements as yttrium, lanthanum, arid thorium3,4 or strong nitride formers5 has been shown capable of reducing nitrogen embrittlement, it is apparent that some additional form of surface protection, such as coatings or claddings, will be required for long time service in air breathing engines. Studies of aluiminide6 and silicide7 coatings and of nickel-base claddingsl on chromium alloys to date have suggested that these protection systems are inadequate. Of the aluminidc systems Studied,6 a simple aluminum and an Fe-Al coating on a Cr-5 pct W-0.1 pct Y alloy showed the lowest air exposure weight gains. However, the air exposures raised the ductile-brittle transition temperature of the coated specimens to above 1600°F from an initial level in unexposed specimens of about 500°F. A second in-vestigation for protection of Cr-5 pct W-0.1 pct Y employed gas pressure bonded alloy foils as protective claddings.1 An aluminized Ni-20 pct Cr-20 pct W alloy plus an unalloyed tungsten barrier layer gave the best performance with air exposure lives based on appearance and weight gains of over 600 hr at 2100°F. However, the bend ductile-brittle transition tempera-ture was increased to at least 1000°F after 100 hr at

Jan 1, 1970

By J. P. Josien, Didier C.

ABSTRACT: France now faces the closure of most of its mining sites. Surface instability risk may sometimes remain, especially where large underground voids exist. This paper illustrates the importance of failure mechanisms identification in order to define properly how to manage the residual risk. RESUME: La France fait aujourd’hui face à la fermeture de ses exploitations minières. Des risques d’instabilités de surface peuvent persister, notamment lorsque des vides résiduels existent au sein des travaux souterrains. L’article illustre l’importance que présente la nature des mécanismes de rupture potentiels dans le choix des mesures compensatoires à adopter pour gérer le risque résiduel à long terme. ZUSAMMENFASSUNG: In Frankreich stellt sich derzeit das Problem der definitiven Schliessung des meisten Bergwerke. In manchen fällen ist die Stabilität der Oberfläche nicht garantiert, speziell wenn unter Tage nicht verfüllte Hohlräume verblieben sind. Dieser Bericht zeigt die Wichtigkeit, bei der Auswahl geeigneter Langzeit-Risikomanagementmethoden, der verschiedenen Mechanismen mit denen ein eventueller Bruch an die Tagesoberfläche geraten kann.

Jan 1, 2003

By C. M. McKinney

This report contains Bureau of Mines routine analyses of 492 samples of crude petroleum from 470 United States oilfields, each of which produced 2,500 barrels a day or more during at least 1 of the years 1946-56. The fields are listed alphabetically by State and field names in table 1, with information on the geographical and geological sources of the samples. Table 2 summarizes the general characteristics of the crude oils and analytical and computed data determined from the analyses. A previous report 4 contains similar analyses of 283 important United States oilfields; some of them are repeated in this report. Many fields for which analyses previously were published are represented by new analyses, which include data not previously reported. Refractive index nu and specific dispersion, ng minus nD divided by the density, for some of the distillate fractions are included in the analyses of 316 of the crude-oil samples. This is the first Bureau of Mines report on analysis of crude oils to contain such data, and their use in calculating hydrocarbon-type composition of the fractions is explained.

Jan 1, 1957

By R. Dippenaar

Traditionally, iron ore has been reduced with coke in a blast furnace and the hot-metal product of the blast furnace containing carbon, manganese, silicon, sulphur and phosphorous, was subsequently refined in a steelmaking furnace. During iron making as well as during steelmaking, significant amounts of slag are produced. Two decades ago, more than 13 m tonne of blast furnace slag and 4 m tonne of steelmaking slag per annum were produced in the USA alone. It is, therefore, not surprising that many attempts have been made to re-use iron and steelmaking slags. However, these slags are not merely metallurgical waste products but, on the contrary, their compositions and physical properties are judiciously designed to optimize the operations in the respective metallurgical reactors. The variation in composition and properties of blast furnaces lags are largely determined by the gangue in the ore and ash in the coke and much progress has been made in the re-use of such slag. With respect to steelmaking slag, emphasis has in recent years been placed on hot-metal treatment before refining and ladle treatment after decarburization. The bulk removal of silicon, phosphorous and sulphur from the hot-metal product of the blast furnace by specially designed slags prior to refining in a basic oxygen furnace, has reduced tap-to-tap time, lowered cost and produced steel of much higher quality. The use of synthetic slags in ladle refining techniques subsequent to decarburization in the basic oxygen furnace has resulted in reduced hydrogen and nitrogen contents and reduced solute impurities. Moreover, inclusion shape and composition control, again by the use of specially designed slags has led to the achievement of much improved mechanical properties of the steel. In these revised process routes, slag of different compositions are produced in the variety of unit processes and hence the re-use of steelmaking slags has become much more complex. Clearly, a thorough understanding of the design and use of these different slags is a pre-requisite to the development of re-use strategies. Japanese steelmakers have spearheaded attempts to reduce slag volumes in the individual unit processes and to strive towards ‘slagless steelmaking’ by recycling slags internally. Steelmaking slag volumes have been reduced on commercial scale from about 140 kg/tonne steel to 60kg/tonne steel. Moreover, model predictions have shown that, in principle, all slag can be recycled and the phosphorous extracted to produce fertilizer. This development is of particular significance since the supply of low-phosphorous iron ores is diminishing at an ever increasing rate. Keywords: slag, environment, iron, steel,

Jan 1, 2004

In 1987 Wyoming became the largest coal producing state in the country. The state is known for its extensive coal resources and extremely thick coal seams. Wyoming's coal reserves total about 69.3 billion tons, or 14.2 percent of the U.S. coal reserve. Coal seams range generally from 10 to 80 feet in thickness, although one seam is 220 feet thick. The coal-bearing areas of Wyoming underlie approximately 41 percent of the state's total land area. Wyoming's coal ranges from lignite to high volatile bituminous. Most of the coal produced is subbituminous from the Powder River coal region near Gillette. The presence of coal in Wyoming was discovered before 1834 on the Belle Fourche River. The state's first mine opened in Carbon County in 1865, and with the completion of the trans- continental railroad, the demand for coal increased. Currently approximately 80 percent of Wyoming's coal production is shipped out-of-state to meet the growing demand for low- sulfur coal to fuel electric generating plants. Wyoming received conditional regulatory approval November 26, 1980. Its Abandoned Mine Land Program was approved February 14, 1983.

Jan 1, 1992

By François Girard

La zone 1 de la mine Doyon (zone altérée), se situe à l?extrémité sud de la mine et est constituée d?une série de veines étroites à fort pendage et ayant des épontes de très faible résistance. Les épontes supérieure et inférieure ont des valeurs de RQD variant de 0 à 20 lors que les valeurs de RQD de la zone minéralisée se situent entre 20 et 40. Le minerai de la zone 1 s?étend sur environ 300 m de long et sur 900 m de profondeur avec des épaisseurs variant entre 2 et 15 m. Des méthodes de minage long-trous y sont utilisées avec des accès longitudinaux ou transverses selon l?épaisseur de la zone minéralisée. L?exploitation de la zone 1 a débuté en 1991 et plus de 1,7 millions de tonnes auront été extraites à la fin 2008. Plusieurs techniques y ont été testées que ce soit au niveau du développement ou du minage afin d?améliorer la sécurité des travailleurs, de réduire la dilution des chantiers et d?en augmenter la récupération. Différentes modifications ont été apportées aux dimensions et orientations des galeries, aux patrons de forage, aux techniques de sautages, au support de terrain, à la séquence de minage et aux méthodes de remblayage. Le texte suivant élabore sur plusieurs approches utilisées lors du minage de la zone 1.

Feb 1, 2008

Jan 1, 1969

Brunswick Mine employs an ore and waste pass system for material transfer. This paper reviews the evolution and performance ore pass systems at the mine. It presents the range of selected configurations, inclination, dimensions etc. Select case studies are used to address the influence of structure, stress and materials handling on the longevity of the employed ore passes.

Feb 1, 2008

By W. Z. Rogers

U.S. feldspar output sold or used in 2005 was an estimated 760 kt (838,000 st), valued at $44 million free-on-board plant. This was below the 2004 volume and was the second year of decline in a row. Output included flotation concentrates, feldspar content in feldspar-silica mixtures, potash feldspar and aplite. The strong housing market in the United States maintained demand for ceramic tiles, plumbing fixtures and fiberglass insulation requiring feldspar. Shipments of glass containers were about the same as in 2004. Imports of ceramic tiles and plumbing fixtures continued to increase, taking the place of U.S.-produced goods and the feldspar required to make them. For 2005, 80 percent of the ceramic tiles sold and 50 percent of the plumbing fixtures sold in the United States were imported. Since 2000, manufacturing plant closures in the plumbing fixtures industry have reduced the demand for feldspar and feldspar-silica mixtures by 100 kt (110,000 st). Increased demand from the ceramic tile industry has partially offset the lost volume.

Jan 1, 2006

By V. T. McLemore

In-situ leaching (ISL) operations have been proposed to recover uranium from sandstone-uranium deposits in NM. ISL (also known as in-situ recovery, solution mining, solution-leach mining, leach mining) consists of injecting a leaching solution into the mineralized zone through injection wells. The leach solution migrates through the formation, dissolves uranium and is recovered through production wells. The uranium is then precipitated through a conventional uranium recovery system. Several criteria must be met in order for in-situ leaching to be successful, most important is that the ore body must be amenable to chemical leaching. A number of ISL operations have been conducted in NM in the past (Mobil, Crownpoint; UNC-Teton, Section 23; Grace Nuclear, Hook?s Ranch, Seboyeta, Church Rock; Anaconda, Windwhip). Kerr-McGee (later Quivera Mining Co., Rio Algum) successfully produced uranium from mine-water recovery (recirculated mine water) from the Ambrosia Lake mines (mid-1960s to 2002). Despite some difficulties, ISL is a viable alternative to recovering uranium and could be utilized in the Grants district with proper aquifer characterization and monitoring.

Jan 1, 2009