Search Documents

By H. Sevim, M. K. Mohanty, Y. P. Chugh

The economics of “Conventional” and “Advanced Fine Coal Cleaning” (AFCC) circuits for refuse pond reclamation as well as active mine/preparation plant applications have been evaluated. The benefits of innovative tailings management schemes on the profitability of mining enterprises have also been evaluated as a part of this study. Analyses have been conducted for scenarios involving generation of two different product qualities of 5.81%, a quality that was obtained during AFCC circuit operation at SIU, and a more typical 8% product ash. The inability of the conventional circuits to achieve profitability while producing the lower ash content product is revealed from this approach. The spiral-only circuit is unable to produce a 5.81% ash product. A different version of the same circuit involving spirals and column flotation produced the desired product quality but could not maintain profitability. The AFCC circuits on the other hand, achieve net present values greater than $6 million, with return on investment in excess of 50%, in the water-only as well as dense medium mode, with and without tailings management. Addition of tailings management system to any of the circuits is found to enhance the project economics. The comparison of water-only and dense-medium applications of the AFCC circuits indicate a better suitability of the dense-medium circuit for producing premium quality products. Application of AFCC circuits in active mines offer better economics compared to applications in refuse pond recovery operations. The superior project economics are a result of reduced overhead cost and use of existing material handling facilities. Sensitivity analysis reveals the significance of capacity utilization on project economics.

Jan 1, 2002

By V. Wetzig

In the past, various investigations have been carried out at the Hagerbach Experimental Gallery under accurately reproducible conditions, in order to determine the emissions emanating from blasting operations. Comparative investigations proved that the composition of the blast fumes is influenced by the choice of different explosives. It also emerged that the use of emulsion explosives leads to significantly lower concentrations of harmful substances in the blast fumes. Further investigations concerned the residues and reaction products from the explosive process which are left in the debris. Eluate tests on representative samples of debris were used to determine the concentrations of nitrate, nitrite and ammonium in the debris.

Jan 1, 2001

Microfluidic Solvent Extraction for Mineral Processing of Copper Leach Solutions

Sep 13, 2010

By Jaime Fernández Concha

El presente texto señala la ubicación, fisiografía, geología general y cubicación del depósito de Fierro del Cerro Tarpuy y Cerro Mirador ubicado en el departamento de Arequipa.

Jul 1, 1956

By W. H. Oppelt

Converting small-particle lignite to a stable, storable fuel of relatively high heating value was investigated. The fuel was prepared by thermal pretreatment of the lignite in an 8-inch i. d. rotary-drum retort, then the pretreated material was pelletized in an experimental 15-inch-i. d. rotary-drum pelletizer. Pelletizing tests were made with both starch and bituminous binders. During the first phase of the project, the quantity, composition, and heating value of products from the thermal processing of Kincaid lignite from Burke County, N. Dak., in an B-inch i. d. rotary-drum retort were investigated at a series of temperatures from 250° to 950° F. to establish optimum conditions for preparing feed material for pelletizing. To determine the response to thermal treatment of different lignites, 5 other lignites from Divide, McLean, Mercer, and Stark Counties, N. Dak., and 1 lignite from Saskatchewan, Canada, were processed at 700° F.

Jan 1, 1958

By Forrest T. Moyer

Frequency rates of injuries per million man-hours of exposure were improved during 1965 slightly to moderately over those of 1964 at metal mines, nonferrous reduction and refining plants, nonmetal mills, stone quarries and mills, sand and gravel operations, and slag operations. However, at metal mills and nonmetal mines the rates of occurrence of work injuries were less favorable. The severity rates of injuries during 1965 were better than in 1964 at metal mines and mills, stone quarries and mills, and slag operations. Conversely, severity rates were worse at nonferrous reduction and refining plants, nonmetal mines and mills, and sand and gravel operations.

Jan 1, 1966

To the members of The South African Institute of Mining and Metallurgy We have audited the annual financial statements of The South African Institute of Mining and Metallurgy set out on pages 357 to 366 for the year ended 30 June 2002. These financial statements are the responsibility of the Institute?s Council. Our responsibility is to express an opinion on these financial statements based on our audit. Scope We have conducted our audit in accordance with statements of South African Auditing Standards. Those standards require that we plan and perform the audit to obtain reasonable assurance that the financial statements are free of material misstatement. An audit includes: ?examining, on a test basis, evidence supporting the amounts and disclosures in the financial statements, ?assessing the accounting principles used and significant estimates made by management, and ?evaluating the overall financial statement presentation. Audit opinion In our opinion, the financial statements fairly present, in all material respects, the financial position of the Institute at 30 June 2002 and the results of its operations and cash flows for the year then ended in accordance with South African Statements of Generally Accepted Accounting Practice. Auditors 26 July 2002 Council?s approval of the annual financial statements The annual financial statements for the year ended 30 June 2002 set out on page 357 to 366 wereapproved by the Council on 26 July 2002 and are signed on its behalf by:

Jan 1, 2002

By Karen C. Armfield, Gisele R. Passalacqua, Joanna Smith

When selecting a solution for improving resiliency at facilities, such as airports, utility and transit sites, there are many options to protect structures and equipment against potential flooding. Each case involves an evaluation of the several key factors such as: design flood parameters, the geography and geological conditions below the site, the facility, and the layout of buildings and equipment to be protected. Upon reviewing these conditions and conducting a cost analysis of various options, the most suitable approach to protecting a facility can be determined. This paper will compare the conditions at various New York City sites, and give detail to the solutions utilized at these sites to improve resiliency and protect each facility. Flood wall types varied as did the strategies for raising critical equipment, to meet the Federal Emergency Management Agency (FEMA) and American Society of Civil Engineers (ASCE) 7 guidelines. Due to granular soil conditions, some sites may experience soil seepage below the flood wall resulting in the need for underground cut off systems. The authors will also present detail regarding the solutions used to control seepage. Various cut off systems will be discussed such as grouting and sheeting, explaining the factors that may impact the choice of systems. Another consideration in flood resiliency is the potential for a buoyancy condition on basement slabs when localized flood barriers are employed on first floor doors and windows. The authors will discuss the potential impacts of this condition on facilities and methods to mitigate this issue. 1. INTRODUCTION New York City is an urban coastal Metropolis with varied geology and low land areas. This includes but is not limited to sandy soils at Coney Island and the John F. Kennedy Airport. Soft marshes are found near Flushing Queens and LaGuardia Airport. Heavy rains and coastal storms caused disruption to daily life and heavily affected the economy of this vibrant City. For instance, in lower Manhattan business was interrupted in the Financial District. Power outage was widespread; commuter trains and subways were stopped and put out of service. Additionally, numerous residential homes were damaged in Coastal Neighborhoods such as the Far Rockaways and Staten Island. 1.1. Superstorm Sandy Flood Statistics On October 29, 2012 Superstorm Sandy impacted numerous facilities in the New York City Metro area. The resulting damage cost New York City more than $42 billion in repair costs. $33 billion was allocated to repair housing and infrastructure, and $9 billion was allocated to protect transit systems1. One of the major issues that impacted the city in terms of its preparedness was the high flood surge. The surge surpassed the former base flood elevation and reached as high as 13.88 feet (above mean lower low water - MLLW) in Battery Park at 9:24pm that evening. Tottenville, Staten Island experienced more damage where the water was recorded at +16 (North America Vertical Datum of 1988 - NAVD88), which is equivalent to 18.7 feet above MLLW (see Fig. 1). Not only was the surge at record levels, the waves in New York Harbor were also at record level where some buoy stations recorded waves of up to 32.5 feet. The City released “A Stronger, More Resilient New York” in June 2013, a plan laid out to rebuild communities impacted by Sandy and improve the resiliency of the infrastructure and buildings in New York City. Figures below help to illustrate the extent of the inundation relative to the projects being discussed.

Jan 1, 2018

By O. M. McRae

The Courtland-Gleeson area is in Cochise County about 15 miles east of Tombstone in southeastern Arizona. Rocks exposed in the area range in age from Pre-cambrian to Quaternary. The Precambrian is repre-sented by the Pinal schist. Paleozoic rocks include the Cambrian Bolsa quartzite and Abrigo limestone, Mississippian Escabrosa limestone, and the Permo-Carboniferous Naco Group limestones. Rocks believed to be of Triassic and/or Jurassic age include the Copper Belle monzonite porphyry, Turquoise granite, and Gleeson quartz monzonite. The Cretaceous is represented by andesitic volcanics and various sedimentary rocks. Tertiary rocks include the intrusive and extrusive Sugarloaf quartz latite porphyry and numerous dikes of various rock types. Quaternary conglomerates cover the northern and eastern part of the area. The geologic structure is extremely complex. All rocks as old as early Tertiary have been involved in either tilting, normal faulting, high angle reverse faulting, imbricate thrusting or folding and overfold-ing. Major deformation was initiated during the first half of the Tertiary. Northeast-southwest compres-sional forces caused thrust plates containing lower Paleozoic rocks to override Cretaceous rocks. Subsequently, two large slide blocks of lower Paleozoic rocks, acting under the influence of gravity, moved eastward. The imbricate structure and the gravity slide blocks were then broken by late Tertiary normal faults. INTRODUCTION The Courtland-Gleeson area, or Turquoise Mining District, has long been recognized as an area of extreme structural complexity. Gilluly 2 referred to the entire district as a "gigantic thrust breccia". In 1962, Bear Creek Mining Company completed a two year program of detailed geologic mapping supported by exploration drilling. The purpose of this paper is to present some of the results of this investigation and to provide a structural interpretation based on these results. The geologic map that accompanies this report is generalized and shows only the major and significant features. The area was initially mapped on aerial photographs on a scale of 1 in. equals approximately 500 ft. These data were transferred to a planimetric base using a vertical sketch master. LOCATION The Courtland-Gleeson area is in central Cochise County, about fifteen miles east of Tombstone, and about twenty-two miles northeast of Bisbee in southeastern Arizona (Fig. 1). The area is readily accessible over graded gravel roads from both Tombstone and Elfrida. GENERAL GEOLOGY Rocks exposed in the area range in age from Pre-cambrian to Quaternary. wilson3 and Gilluly2 have published very detailed descriptions of the principal rock units exposed in the area. Only a summary description is provided in Table I. A great number of previously unmapped narrow Tertiary dikes and small irregular masses of hornblende andesite porphyry, lamprophyre, and aplite intrude the Gleeson quartz monzonite in the western part of the map area. The scale of the map prohibits showing them. The aplite dikes are related to, and bear the same structural relationships as, the Sugarloaf quartz latite dikes found in this area. For that reason, and because both the hornblende andesite porphyry and the lamprophyre are post-mineral and post-thrusting, their omission from the map is not considered significant. Because so many of the contacts in the district are fault contacts, because bedding faults appear to be prevalent but are difficult to recognize and map, and because igneous intrusions are so common throughout the sedimentary section, it is virtually impossible to measure an exact total thickness of any of the sedimentary rock units. Nevertheless, neither the field mapping program nor the diamond drilling provided any basis for suspecting that the thicknesses of the sedimentary units are significantly greater or less than what might be inferred from surrounding districts.

Jan 1, 1967

By Ramón Estrella

El presente texto describe el "Smooth Blasting", como un método de voladura controlada que posibilita la superficie de corte lisa y evita el agrietamiento excesivo de la roca. Entre los objetivos principales del método tenemos: el aprovechar la misma roca como pared directa del pique y así desarrollar el empotramiento de puntales de pino, eliminando los cuadros convencionales. Asimismo, genera una superficie lisa de la roca residual que desaparece la rotura y aprovecha las condiciones de la roca existente de la zona.

Nov 8, 1984

By Michael Allen, Paul Worsey

In underground blasting, the pull of the initial cut is the limiting factor for the success of the rest of the round. By improving the pull of the first cut, a critical step is made towards improving the entire round. This project attempted to optimize a burn cut’s effective pull by varying the depths of the relief holes in the burn. The effect of varying the depths of the relief holes was investigated, including depths longer than that of the cut’s charged holes. The overall objective was to consistently achieve greater pull than in a standard burn, using an identical amount of explosives. Increased pull results in savings of both time and cost in underground heading advance.

Jan 1, 2015

By T. A. Sullivan

The processing of sweated aluminum electronic scrap was investigated to develop methods for recovering the aluminum and concentrating the other metals, including copper, lead, gold, and silver, into a product that can be separated by known methods. Two molten-salt electrorefining processes were developed and tested. The first process utilized a three-layer refining cell with a BaCI2-NaF-AIF3 electrolyte, which operated at 750° to 850° C. The second process used an all-chloride electrolyte of NaCI-KCI-AICI3 at 750° to 800° C, with separate anode and cathode compartments. High-quality aluminum was recovered that averaged 99.8-percent pure in the three-layer cell and 99.6-percent pure in the compartment cell. Over 94 percent of the aluminum was recovered with cathode current efficiencies of approximately 90 percent in both methods. The copper, lead, tin, silver, gold, and other metals were concentrated threefold in an anode product. Separation of lead and part of the tin by liquation from this product seemed feasible. The anode product was smelted to prepare a 96-percent copper bullion that contained 690 ounces of silver and 65 ounces of gold per ton, with 98 percent recovery of these values.

Jan 1, 1972

ALAN W. CZARNOWSKY RMCMI PRESIDENT 1988-1989 on behalf of the RMCMI Board of Directors and Officers of The Rocky Mountain Coal Mining Institute cordially invites you and your family to attend the 85th Regular Meeting and Convention to be held June 25, 26 and 27, 1989 at Tamarron Durango, Colorado

Jan 1, 1988

By Hossein Aminian, Daniel Hodouin, Claude Bazin, Claude Jacob

"Solvent extraction followed by electrowinning (SXEW) is an economical option for the processing of low grade and oxidized copper ore. Phenomenological models were developed to simulate the copper solvent extraction and the electrowinning processes. The two models were linked together to make a SX/EW simulator. The simulator is used to predict the operation of the mines Gaspe pilot plant put in operation in 1996. Results confirm the potential of the simulation that would subsequently be used for student training, process optimization and to assess the performances of control strategies.INTRODUCTIONSolvent extraction followed by electrowinning (SXEW) has become in the last two decades a key process for the recovery of copper from solution obtained by leaching low grade copper ore. Several operations have been commissioned in North and South Americas in the last decade (Arbiter, 1994). In Canada, Gibraltar Mine (Scott, 1991) operates a SX plant followed by electrowinning (EW) to produce copper cathode from leached low-grade ore dumps. From 1996 to 1997 Mines Gaspe operated a pilot plant to test the economical feasibility of leaching an oxidized copper ore, followed by solvent extraction and electrowinning of copper. Despite copper SX/EW processes have the reputation of being low cost operations, plant engineers should always look at way to make the plant more efficient. Process models provide an economic platform to learn, control and ultimately optimize the operation of a plant.Several models have been independently proposed to simulate the SX process (Cadman and Hsu, 1970; Medina Gomez, 1980; Wilkinson and Ingham, 1983; Garcia et al., 1988; Aminian et al., 1997) and the EW process (Bryson, 1981; Barton and Scott, 1992; Barton and Scott, 1993). However few papers, if any, deal with the integration of the two process models into a single simulator of a SX-EW plant. This paper describes the development of an integrated simulator for the SX-EW process and shows some steady-state simulation runs of an actual SX-EW pilot plant. The paper consists of four sections. The first section shows the general layout and principles of operation of a SX-EW plant.The second section describes the SX model while the third section deals with the process model used for the copper electrowinning process. The last section shows how the two process models are linked to simulate the operation of the Gaspe pilot plant."

Jan 1, 1999

Roles of Mineral Impurities and Sulfur in the Leaching Behaviour of Pre-Reduced Ilmenite Ores

Sep 13, 2010

By Tom Barry, Kameron Ray, Dr. Gavin Yuill

Imerys Talc, Yellowstone Mine in Montana faces significant geotechnical challenges such as poor wall quality and local instabilities. These instabilities are driven primarily by the characteristics of the rock mass, but are aggravated by drilling and blasting operations.

Jan 1, 2016

H. DEAN JACOT RMCMI PRESIDENT 1987-1988 on behalf of The RMCMI Board of Directors and Officers The Rocky Mountain Coal Mining Institute cordially invites you and your family to attend the 84th Regular Meeting and Convention to be held June 26, 27 and 28, 1988 at Beaver Run Resort Breckenridge, Colorado

Jan 1, 1987

By Gilmar Guzmán Salvador

El proyecto Gold Mill ha permitido a la Minera Yanacocha SRL incorporar durante la vida del proyecto un porcentaje del mineral oxidado y transicional. En este proceso, la composición de la solución rica generada en el circuito de lixiviación del Gol Mill ha causado alteraciones en la planta de adsorción con carbón activado CIC LQ por las concentraciones altas de plata y cobre en solución. En este sentido, para contrarrestar estos efectos negativos se incorporó al circuito el proceso SART (Sulfidization, Acidification, Recycle and Thickening). Por ello, el presente trabajo señala el proceso del SART y su influencia en el proceso de la minera Yanacocha, donde se busca remover los valores metálicos que puedan impactar en la planta de adsorción de oro con carbón activado y así recuperar eficientemente cianuro producto de la disociación del cianuro WAD presente en la solución rica de cianuración que ingresa a la planta SART.

Sep 14, 2009

By D. M. Mubita

Dilution reduction is one of the areas that offer metal mines an opportunity to increase revenue and reduce costs, resulting in enhanced profits. Effective dilution control programmes require interaction on a multi-disciplinary level. This paper outlines recent initiatives undertaken at Konkola Mine to reduce dilution and increase revenue. The increase in revenue arising from reduced dilution and high factors between in situ and delivered to mill grades were quantified and amount to close to U$ 1.0 million per one per cent improvement in grade factor at a 75c/lb copper price. Sources of dilution from open and in?stope mining methods practised at the mine were identified and a multi-disciplinary dilution control forum set up to control these. Among the major achievements were the introduction of low dilution in-stope mining methods; the introduction of Gemcom geological and mining planning software to replace traditional pencil and paper methods, leading to better in situ estimation and production planning; enhanced control in open stopes through dilution awareness among mining production personnel; location of critical secondary development ends in correct positions; enhanced blast hole control; tracking of development waste by metal tracers and monthly tally; implementation of a cavity monitoring system to check over-breaks in open stopes; and setting up of a stope history database. The results from the cavity monitoring system showed that stopes with over-breaks of 5 metres or less could be controlled to break along the hangingwall contact.

Jan 1, 2005

By Claudio Olalla

This paper relates to the foundation of a steel structure located at the San Martin de la Vega (Madrid) amusement park. The structure has more than 100 supports with various loading conditions, including important horizontal and uplift forces. Additionally, the settlement tolerances are very strict. A massive gypsum formation with interbedded clay layers and random solution great voids at various levels constitute the soil. The foundation design has been conditioned large enough these difficulties (load conditions and soil problems). The piling machine used was powerful to drill through the soft rock (UCS up to 11Mpa). The integrity of each pile had to be guaranteed by continuous recording of drilling and concrete pouring parameters. In order to fulfil all those conditions, a STARSOL type-piling rig was used. More than 4500 meters of piles were performed. The diameters of the piles were 450 and 550-mm and their depths varies from 6 to 23 meters. All piles were reinforced over their full length.

Jan 1, 2002